Merge branch 'topic/stm32' into for-linus

Documentation/devicetree/bindings/dma/stm32-dma.txt

@@ -0,0 +1,82 @@
+* STMicroelectronics STM32 DMA controller
+
+The STM32 DMA is a general-purpose direct memory access controller capable of
+supporting 8 independent DMA channels. Each channel can have up to 8 requests.
+
+Required properties:
+- compatible: Should be "st,stm32-dma"
+- reg: Should contain DMA registers location and length. This should include
+  all of the per-channel registers.
+- interrupts: Should contain all of the per-channel DMA interrupts in
+  ascending order with respect to the DMA channel index.
+- clocks: Should contain the input clock of the DMA instance.
+- #dma-cells : Must be <4>. See DMA client paragraph for more details.
+
+Optional properties:
+- resets: Reference to a reset controller asserting the DMA controller
+- st,mem2mem: boolean; if defined, it indicates that the controller supports
+  memory-to-memory transfer
+
+Example:
+
+	dma2: dma-controller@40026400 {
+		compatible = "st,stm32-dma";
+		reg = <0x40026400 0x400>;
+		interrupts = <56>,
+			     <57>,
+			     <58>,
+			     <59>,
+			     <60>,
+			     <68>,
+			     <69>,
+			     <70>;
+		clocks = <&clk_hclk>;
+		#dma-cells = <4>;
+		st,mem2mem;
+		resets = <&rcc 150>;
+	};
+
+* DMA client
+
+DMA clients connected to the STM32 DMA controller must use the format
+described in the dma.txt file, using a five-cell specifier for each
+channel: a phandle plus four integer cells.
+The four cells in order are:
+
+1. The channel id
+2. The request line number
+3. A 32bit mask specifying the DMA channel configuration which are device
+   dependent:
+  -bit 9: Peripheral Increment Address
+	0x0: no address increment between transfers
+	0x1: increment address between transfers
+ -bit 10: Memory Increment Address
+	0x0: no address increment between transfers
+	0x1: increment address between transfers
+ -bit 15: Peripheral Increment Offset Size
+	0x0: offset size is linked to the peripheral bus width
+	0x1: offset size is fixed to 4 (32-bit alignment)
+ -bit 16-17: Priority level
+	0x0: low
+	0x1: medium
+	0x2: high
+	0x3: very high
+5. A 32bit mask specifying the DMA FIFO threshold configuration which are device
+   dependent:
+ -bit 0-1: Fifo threshold
+	0x0: 1/4 full FIFO
+	0x1: 1/2 full FIFO
+	0x2: 3/4 full FIFO
+	0x3: full FIFO
+
+Example:
+
+	usart1: serial@40011000 {
+		compatible = "st,stm32-usart", "st,stm32-uart";
+		reg = <0x40011000 0x400>;
+		interrupts = <37>;
+		clocks = <&clk_pclk2>;
+		dmas = <&dma2 2 4 0x10400 0x3>,
+		       <&dma2 7 5 0x10200 0x3>;
+		dma-names = "rx", "tx";
+	};

arch/arm/configs/stm32_defconfig

@@ -54,6 +54,8 @@ CONFIG_NEW_LEDS=y
 CONFIG_LEDS_CLASS=y
 CONFIG_LEDS_TRIGGERS=y
 CONFIG_LEDS_TRIGGER_HEARTBEAT=y
+CONFIG_DMADEVICES=y
+CONFIG_STM32_DMA=y
 # CONFIG_FILE_LOCKING is not set
 # CONFIG_DNOTIFY is not set
 # CONFIG_INOTIFY_USER is not set

drivers/dma/Kconfig

@@ -431,6 +431,18 @@ config STE_DMA40
 	help
 	  Support for ST-Ericsson DMA40 controller
 
+config STM32_DMA
+	bool "STMicroelectronics STM32 DMA support"
+	depends on ARCH_STM32
+	select DMA_ENGINE
+	select DMA_OF
+	select DMA_VIRTUAL_CHANNELS
+	help
+	  Enable support for the on-chip DMA controller on STMicroelectronics
+	  STM32 MCUs.
+	  If you have a board based on such a MCU and wish to use DMA say Y or M
+	  here.
+
 config S3C24XX_DMAC
 	tristate "Samsung S3C24XX DMA support"
 	depends on ARCH_S3C24XX

drivers/dma/Makefile

@@ -56,6 +56,7 @@ obj-$(CONFIG_QCOM_BAM_DMA) += qcom_bam_dma.o
 obj-$(CONFIG_RENESAS_DMA) += sh/
 obj-$(CONFIG_SIRF_DMA) += sirf-dma.o
 obj-$(CONFIG_STE_DMA40) += ste_dma40.o ste_dma40_ll.o
+obj-$(CONFIG_STM32_DMA) += stm32-dma.o
 obj-$(CONFIG_S3C24XX_DMAC) += s3c24xx-dma.o
 obj-$(CONFIG_TXX9_DMAC) += txx9dmac.o
 obj-$(CONFIG_TEGRA20_APB_DMA) += tegra20-apb-dma.o