media: dt-bindings: ov5675: document YAML binding

This patch adds documentation of device tree in YAML schema for the
OV5675 CMOS image sensor from Omnivision.

Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

Documentation/devicetree/bindings/media/i2c/ovti,ov5675.yaml

@@ -0,0 +1,122 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+# Copyright (c) 2022 Theobroma Systems Design und Consulting GmbH
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/media/i2c/ovti,ov5675.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Omnivision OV5675 CMOS Sensor
+
+maintainers:
+  - Quentin Schulz <quentin.schulz@theobroma-systems.com>
+
+allOf:
+  - $ref: /schemas/media/video-interface-devices.yaml#
+
+description: |
+  The Omnivision OV5675 is a high performance, 1/5-inch, 5 megapixel, CMOS
+  image sensor that delivers 2592x1944 at 30fps. It provides full-frame,
+  sub-sampled, and windowed 10-bit MIPI images in various formats via the
+  Serial Camera Control Bus (SCCB) interface.
+
+  This chip is programmable through I2C and two-wire SCCB. The sensor output
+  is available via CSI-2 serial data output (up to 2-lane).
+
+properties:
+  compatible:
+    const: ovti,ov5675
+
+  reg:
+    maxItems: 1
+
+  clocks:
+    description:
+      System input clock (aka XVCLK). From 6 to 27 MHz.
+    maxItems: 1
+
+  dovdd-supply:
+    description:
+      Digital I/O voltage supply, 1.8 volts.
+
+  avdd-supply:
+    description:
+      Analog voltage supply, 2.8 volts.
+
+  dvdd-supply:
+    description:
+      Digital core voltage supply, 1.2 volts.
+
+  reset-gpios:
+    description:
+      The phandle and specifier for the GPIO that controls sensor reset.
+      This corresponds to the hardware pin XSHUTDN which is physically
+      active low.
+    maxItems: 1
+
+  port:
+    $ref: /schemas/graph.yaml#/$defs/port-base
+    additionalProperties: false
+
+    properties:
+      endpoint:
+        $ref: /schemas/media/video-interfaces.yaml#
+        unevaluatedProperties: false
+
+        properties:
+          data-lanes:
+            minItems: 1
+            maxItems: 2
+
+          # Supports max data transfer of 900 Mbps per lane
+          link-frequencies: true
+
+required:
+  - compatible
+  - reg
+  - clocks
+  - dovdd-supply
+  - avdd-supply
+  - dvdd-supply
+  - port
+
+unevaluatedProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/clock/px30-cru.h>
+    #include <dt-bindings/gpio/gpio.h>
+    #include <dt-bindings/pinctrl/rockchip.h>
+
+    i2c {
+        #address-cells = <1>;
+        #size-cells = <0>;
+
+        ov5675: camera@36 {
+            compatible = "ovti,ov5675";
+            reg = <0x36>;
+
+            reset-gpios = <&gpio2 RK_PB1 GPIO_ACTIVE_LOW>;
+            pinctrl-names = "default";
+            pinctrl-0 = <&cif_clkout_m0>;
+
+            clocks = <&cru SCLK_CIF_OUT>;
+            assigned-clocks = <&cru SCLK_CIF_OUT>;
+            assigned-clock-rates = <19200000>;
+
+            avdd-supply = <&vcc_1v8>;
+            dvdd-supply = <&vcc_1v2>;
+            dovdd-supply = <&vcc_2v8>;
+
+            rotation = <90>;
+            orientation = <0>;
+
+            port {
+                ucam_out: endpoint {
+                    remote-endpoint = <&mipi_in_ucam>;
+                    data-lanes = <1 2>;
+                    link-frequencies = /bits/ 64 <450000000>;
+                };
+            };
+        };
+    };
+...

MAINTAINERS

@@ -15467,6 +15467,7 @@ M:	Shawn Tu <shawnx.tu@intel.com>
 L:	linux-media@vger.kernel.org
 S:	Maintained
 T:	git git://linuxtv.org/media_tree.git
+F:	Documentation/devicetree/bindings/media/i2c/ovti,ov5675.yaml
 F:	drivers/media/i2c/ov5675.c
 
 OMNIVISION OV5693 SENSOR DRIVER