microsoft
/
WSL2-Linux-Kernel
зеркало из https://github.com/microsoft/WSL2-Linux-Kernel.git
1
0
Форкнуть 0
Код Задачи Пакеты Проекты Релизы Вики Активность

Merge branch 'e1000-fixes' of git://198.78.49.142/~jbrandeb/linux-2.6

This commit is contained in:
Jeff Garzik 2006-03-21 16:40:51 -05:00
Родитель 0b5bf225c0 55be062d2d
Коммит ca94f26d2b
3 изменённых файлов: 493 добавлений и 283 удалений
Показать статистику Скачать Patch файл Скачать Diff файл Показать все файлы Свернуть все файлы

158
Documentation/networking/e100.txt
Просмотреть файл

@ -1,16 +1,17 @@
Linux* Base Driver for the Intel(R) PRO/100 Family of Adapters
==============================================================
November 17, 2004
November 15, 2005
Contents
========
- In This Release
- Identifying Your Adapter
- Building and Installation
- Driver Configuration Parameters
- Additional Configurations
- Known Issues
- Support
@ -18,18 +19,30 @@ In This Release
===============
This file describes the Linux* Base Driver for the Intel(R) PRO/100 Family of
Adapters, version 3.3.x. This driver supports 2.4.x and 2.6.x kernels.
Adapters. This driver includes support for Itanium(R)2-based systems.
For questions related to hardware requirements, refer to the documentation
supplied with your Intel PRO/100 adapter.
The following features are now available in supported kernels:
- Native VLANs
- Channel Bonding (teaming)
- SNMP
Channel Bonding documentation can be found in the Linux kernel source:
/Documentation/networking/bonding.txt
Identifying Your Adapter
========================
For more information on how to identify your adapter, go to the Adapter &
For more information on how to identify your adapter, go to the Adapter &
Driver ID Guide at:
http://support.intel.com/support/network/adapter/pro100/21397.htm
For the latest Intel network drivers for Linux, refer to the following
website. In the search field, enter your adapter name or type, or use the
For the latest Intel network drivers for Linux, refer to the following
website. In the search field, enter your adapter name or type, or use the
networking link on the left to search for your adapter:
http://downloadfinder.intel.com/scripts-df/support_intel.asp
@ -40,73 +53,75 @@ Driver Configuration Parameters
The default value for each parameter is generally the recommended setting,
unless otherwise noted.
Rx Descriptors: Number of receive descriptors. A receive descriptor is a data
structure that describes a receive buffer and its attributes to the network
controller. The data in the descriptor is used by the controller to write
data from the controller to host memory. In the 3.0.x driver the valid
range for this parameter is 64-256. The default value is 64. This parameter
can be changed using the command
Rx Descriptors: Number of receive descriptors. A receive descriptor is a data
structure that describes a receive buffer and its attributes to the network
controller. The data in the descriptor is used by the controller to write
data from the controller to host memory. In the 3.x.x driver the valid range
for this parameter is 64-256. The default value is 64. This parameter can be
changed using the command:
ethtool -G eth? rx n, where n is the number of desired rx descriptors.
Tx Descriptors: Number of transmit descriptors. A transmit descriptor is a
data structure that describes a transmit buffer and its attributes to the
network controller. The data in the descriptor is used by the controller to
read data from the host memory to the controller. In the 3.0.x driver the
valid range for this parameter is 64-256. The default value is 64. This
parameter can be changed using the command
Tx Descriptors: Number of transmit descriptors. A transmit descriptor is a data
structure that describes a transmit buffer and its attributes to the network
controller. The data in the descriptor is used by the controller to read
data from the host memory to the controller. In the 3.x.x driver the valid
range for this parameter is 64-256. The default value is 64. This parameter
can be changed using the command:
ethtool -G eth? tx n, where n is the number of desired tx descriptors.
Speed/Duplex: The driver auto-negotiates the link speed and duplex settings by
default. Ethtool can be used as follows to force speed/duplex.
Speed/Duplex: The driver auto-negotiates the link speed and duplex settings by
default. Ethtool can be used as follows to force speed/duplex.
ethtool -s eth? autoneg off speed {10|100} duplex {full|half}
NOTE: setting the speed/duplex to incorrect values will cause the link to
fail.
Event Log Message Level: The driver uses the message level flag to log events
to syslog. The message level can be set at driver load time. It can also be
set using the command
Event Log Message Level: The driver uses the message level flag to log events
to syslog. The message level can be set at driver load time. It can also be
set using the command:
ethtool -s eth? msglvl n
Additional Configurations
=========================
Configuring the Driver on Different Distributions
-------------------------------------------------
Configuring a network driver to load properly when the system is started is
distribution dependent. Typically, the configuration process involves adding
an alias line to /etc/modules.conf as well as editing other system startup
scripts and/or configuration files. Many popular Linux distributions ship
with tools to make these changes for you. To learn the proper way to
configure a network device for your system, refer to your distribution
documentation. If during this process you are asked for the driver or module
name, the name for the Linux Base Driver for the Intel PRO/100 Family of
Adapters is e100.
Configuring a network driver to load properly when the system is started is
distribution dependent. Typically, the configuration process involves adding
an alias line to /etc/modules.conf or /etc/modprobe.conf as well as editing
other system startup scripts and/or configuration files. Many popular Linux
distributions ship with tools to make these changes for you. To learn the
proper way to configure a network device for your system, refer to your
distribution documentation. If during this process you are asked for the
driver or module name, the name for the Linux Base Driver for the Intel
PRO/100 Family of Adapters is e100.
As an example, if you install the e100 driver for two PRO/100 adapters
(eth0 and eth1), add the following to modules.conf:
As an example, if you install the e100 driver for two PRO/100 adapters
(eth0 and eth1), add the following to modules.conf or modprobe.conf:
alias eth0 e100
alias eth1 e100
Viewing Link Messages
---------------------
In order to see link messages and other Intel driver information on your
console, you must set the dmesg level up to six. This can be done by
entering the following on the command line before loading the e100 driver:
In order to see link messages and other Intel driver information on your
console, you must set the dmesg level up to six. This can be done by
entering the following on the command line before loading the e100 driver:
dmesg -n 8
If you wish to see all messages issued by the driver, including debug
If you wish to see all messages issued by the driver, including debug
messages, set the dmesg level to eight.
NOTE: This setting is not saved across reboots.
Ethtool
-------
@ -114,29 +129,27 @@ Additional Configurations
diagnostics, as well as displaying statistical information. Ethtool
version 1.6 or later is required for this functionality.
The latest release of ethtool can be found at:
http://sf.net/projects/gkernel.
The latest release of ethtool can be found from
http://sourceforge.net/projects/gkernel.
NOTE: This driver uses mii support from the kernel. As a result, when
there is no link, ethtool will report speed/duplex to be 10/half.
NOTE: Ethtool 1.6 only supports a limited set of ethtool options. Support
for a more complete ethtool feature set can be enabled by upgrading
ethtool to ethtool-1.8.1.
NOTE: Ethtool 1.6 only supports a limited set of ethtool options. Support
for a more complete ethtool feature set can be enabled by upgrading
ethtool to ethtool-1.8.1.
Enabling Wake on LAN* (WoL)
---------------------------
WoL is provided through the Ethtool* utility. Ethtool is included with Red
Hat* 8.0. For other Linux distributions, download and install Ethtool from
the following website: http://sourceforge.net/projects/gkernel.
WoL is provided through the Ethtool* utility. Ethtool is included with Red
Hat* 8.0. For other Linux distributions, download and install Ethtool from
the following website: http://sourceforge.net/projects/gkernel.
For instructions on enabling WoL with Ethtool, refer to the Ethtool man
page.
For instructions on enabling WoL with Ethtool, refer to the Ethtool man page.
WoL will be enabled on the system during the next shut down or reboot. For
this driver version, in order to enable WoL, the e100 driver must be
this driver version, in order to enable WoL, the e100 driver must be
loaded when shutting down or rebooting the system.
NAPI
----
@ -144,6 +157,25 @@ Additional Configurations
See www.cyberus.ca/~hadi/usenix-paper.tgz for more information on NAPI.
Multiple Interfaces on Same Ethernet Broadcast Network
------------------------------------------------------
Due to the default ARP behavior on Linux, it is not possible to have
one system on two IP networks in the same Ethernet broadcast domain
(non-partitioned switch) behave as expected. All Ethernet interfaces
will respond to IP traffic for any IP address assigned to the system.
This results in unbalanced receive traffic.
If you have multiple interfaces in a server, either turn on ARP
filtering by
(1) entering: echo 1 > /proc/sys/net/ipv4/conf/all/arp_filter
(this only works if your kernel's version is higher than 2.4.5), or
(2) installing the interfaces in separate broadcast domains (either
in different switches or in a switch partitioned to VLANs).
Support
=======
@ -151,20 +183,24 @@ For general information, go to the Intel support website at:
http://support.intel.com
or the Intel Wired Networking project hosted by Sourceforge at:
http://sourceforge.net/projects/e1000
If an issue is identified with the released source code on the supported
kernel with a supported adapter, email the specific information related to
the issue to linux.nics@intel.com.
kernel with a supported adapter, email the specific information related to the
issue to e1000-devel@lists.sourceforge.net.
License
=======
This software program is released under the terms of a license agreement
between you ('Licensee') and Intel. Do not use or load this software or any
associated materials (collectively, the 'Software') until you have carefully
read the full terms and conditions of the LICENSE located in this software
package. By loading or using the Software, you agree to the terms of this
Agreement. If you do not agree with the terms of this Agreement, do not
install or use the Software.
This software program is released under the terms of a license agreement
between you ('Licensee') and Intel. Do not use or load this software or any
associated materials (collectively, the 'Software') until you have carefully
read the full terms and conditions of the file COPYING located in this software
package. By loading or using the Software, you agree to the terms of this
Agreement. If you do not agree with the terms of this Agreement, do not install
or use the Software.
* Other names and brands may be claimed as the property of others.

602
Documentation/networking/e1000.txt
Просмотреть файл

@ -1,7 +1,7 @@
Linux* Base Driver for the Intel(R) PRO/1000 Family of Adapters
===============================================================
November 17, 2004
November 15, 2005
Contents
@ -20,254 +20,316 @@ In This Release
===============
This file describes the Linux* Base Driver for the Intel(R) PRO/1000 Family
of Adapters, version 5.x.x.
of Adapters. This driver includes support for Itanium(R)2-based systems.
For questions related to hardware requirements, refer to the documentation
supplied with your Intel PRO/1000 adapter. All hardware requirements listed
For questions related to hardware requirements, refer to the documentation
supplied with your Intel PRO/1000 adapter. All hardware requirements listed
apply to use with Linux.
Native VLANs are now available with supported kernels.
The following features are now available in supported kernels:
- Native VLANs
- Channel Bonding (teaming)
- SNMP
Channel Bonding documentation can be found in the Linux kernel source:
/Documentation/networking/bonding.txt
The driver information previously displayed in the /proc filesystem is not
supported in this release. Alternatively, you can use ethtool (version 1.6
or later), lspci, and ifconfig to obtain the same information.
Instructions on updating ethtool can be found in the section "Additional
Configurations" later in this document.
Identifying Your Adapter
========================
For more information on how to identify your adapter, go to the Adapter &
For more information on how to identify your adapter, go to the Adapter &
Driver ID Guide at:
http://support.intel.com/support/network/adapter/pro100/21397.htm
For the latest Intel network drivers for Linux, refer to the following
website. In the search field, enter your adapter name or type, or use the
For the latest Intel network drivers for Linux, refer to the following
website. In the search field, enter your adapter name or type, or use the
networking link on the left to search for your adapter:
http://downloadfinder.intel.com/scripts-df/support_intel.asp
Command Line Parameters
=======================
If the driver is built as a module, the following optional parameters are
used by entering them on the command line with the modprobe or insmod command
using this syntax:
Command Line Parameters =======================
If the driver is built as a module, the following optional parameters
are used by entering them on the command line with the modprobe or insmod
command using this syntax:
modprobe e1000 [<option>=<VAL1>,<VAL2>,...]
insmod e1000 [<option>=<VAL1>,<VAL2>,...]
insmod e1000 [<option>=<VAL1>,<VAL2>,...]
For example, with two PRO/1000 PCI adapters, entering:
insmod e1000 TxDescriptors=80,128
loads the e1000 driver with 80 TX descriptors for the first adapter and 128 TX
descriptors for the second adapter.
loads the e1000 driver with 80 TX descriptors for the first adapter and 128
TX descriptors for the second adapter.
The default value for each parameter is generally the recommended setting,
unless otherwise noted. Also, if the driver is statically built into the
kernel, the driver is loaded with the default values for all the parameters.
Ethtool can be used to change some of the parameters at runtime.
unless otherwise noted.
NOTES: For more information about the AutoNeg, Duplex, and Speed
parameters, see the "Speed and Duplex Configuration" section in
this document.
NOTES: For more information about the AutoNeg, Duplex, and Speed
parameters, see the "Speed and Duplex Configuration" section in
this document.
For more information about the InterruptThrottleRate, RxIntDelay,
TxIntDelay, RxAbsIntDelay, and TxAbsIntDelay parameters, see the
application note at:
http://www.intel.com/design/network/applnots/ap450.htm
For more information about the InterruptThrottleRate,
RxIntDelay, TxIntDelay, RxAbsIntDelay, and TxAbsIntDelay
parameters, see the application note at:
http://www.intel.com/design/network/applnots/ap450.htm
A descriptor describes a data buffer and attributes related to the
data buffer. This information is accessed by the hardware.
A descriptor describes a data buffer and attributes related to
the data buffer. This information is accessed by the hardware.
AutoNeg (adapters using copper connections only)
Valid Range: 0x01-0x0F, 0x20-0x2F
AutoNeg
-------
(Supported only on adapters with copper connections)
Valid Range: 0x01-0x0F, 0x20-0x2F
Default Value: 0x2F
This parameter is a bit mask that specifies which speed and duplex
settings the board advertises. When this parameter is used, the Speed and
Duplex parameters must not be specified.
NOTE: Refer to the Speed and Duplex section of this readme for more
information on the AutoNeg parameter.
Duplex (adapters using copper connections only)
Valid Range: 0-2 (0=auto-negotiate, 1=half, 2=full)
This parameter is a bit mask that specifies which speed and duplex
settings the board advertises. When this parameter is used, the Speed
and Duplex parameters must not be specified.
NOTE: Refer to the Speed and Duplex section of this readme for more
information on the AutoNeg parameter.
Duplex
------
(Supported only on adapters with copper connections)
Valid Range: 0-2 (0=auto-negotiate, 1=half, 2=full)
Default Value: 0
Defines the direction in which data is allowed to flow. Can be either one
or two-directional. If both Duplex and the link partner are set to auto-
negotiate, the board auto-detects the correct duplex. If the link partner
is forced (either full or half), Duplex defaults to half-duplex.
Defines the direction in which data is allowed to flow. Can be either
one or two-directional. If both Duplex and the link partner are set to
auto-negotiate, the board auto-detects the correct duplex. If the link
partner is forced (either full or half), Duplex defaults to half-duplex.
FlowControl
Valid Range: 0-3 (0=none, 1=Rx only, 2=Tx only, 3=Rx&Tx)
Default: Read flow control settings from the EEPROM
This parameter controls the automatic generation(Tx) and response(Rx) to
Ethernet PAUSE frames.
----------
Valid Range: 0-3 (0=none, 1=Rx only, 2=Tx only, 3=Rx&Tx)
Default Value: Reads flow control settings from the EEPROM
This parameter controls the automatic generation(Tx) and response(Rx)
to Ethernet PAUSE frames.
InterruptThrottleRate
Valid Range: 100-100000 (0=off, 1=dynamic)
---------------------
(not supported on Intel 82542, 82543 or 82544-based adapters)
Valid Range: 100-100000 (0=off, 1=dynamic)
Default Value: 8000
This value represents the maximum number of interrupts per second the
controller generates. InterruptThrottleRate is another setting used in
interrupt moderation. Dynamic mode uses a heuristic algorithm to adjust
InterruptThrottleRate based on the current traffic load.
Un-supported Adapters: InterruptThrottleRate is NOT supported by 82542, 82543
or 82544-based adapters.
NOTE: InterruptThrottleRate takes precedence over the TxAbsIntDelay and
RxAbsIntDelay parameters. In other words, minimizing the receive
and/or transmit absolute delays does not force the controller to
generate more interrupts than what the Interrupt Throttle Rate
allows.
CAUTION: If you are using the Intel PRO/1000 CT Network Connection
(controller 82547), setting InterruptThrottleRate to a value
greater than 75,000, may hang (stop transmitting) adapters under
certain network conditions. If this occurs a NETDEV WATCHDOG
message is logged in the system event log. In addition, the
controller is automatically reset, restoring the network
connection. To eliminate the potential for the hang, ensure
that InterruptThrottleRate is set no greater than 75,000 and is
not set to 0.
NOTE: When e1000 is loaded with default settings and multiple adapters are
in use simultaneously, the CPU utilization may increase non-linearly.
In order to limit the CPU utilization without impacting the overall
throughput, we recommend that you load the driver as follows:
This value represents the maximum number of interrupts per second the
controller generates. InterruptThrottleRate is another setting used in
interrupt moderation. Dynamic mode uses a heuristic algorithm to adjust
InterruptThrottleRate based on the current traffic load.
insmod e1000.o InterruptThrottleRate=3000,3000,3000
NOTE: InterruptThrottleRate takes precedence over the TxAbsIntDelay and
RxAbsIntDelay parameters. In other words, minimizing the receive
and/or transmit absolute delays does not force the controller to
generate more interrupts than what the Interrupt Throttle Rate
allows.
CAUTION: If you are using the Intel PRO/1000 CT Network Connection
(controller 82547), setting InterruptThrottleRate to a value
greater than 75,000, may hang (stop transmitting) adapters
under certain network conditions. If this occurs a NETDEV
WATCHDOG message is logged in the system event log. In
addition, the controller is automatically reset, restoring
the network connection. To eliminate the potential for the
hang, ensure that InterruptThrottleRate is set no greater
than 75,000 and is not set to 0.
NOTE: When e1000 is loaded with default settings and multiple adapters
are in use simultaneously, the CPU utilization may increase non-
linearly. In order to limit the CPU utilization without impacting
the overall throughput, we recommend that you load the driver as
follows:
insmod e1000.o InterruptThrottleRate=3000,3000,3000
This sets the InterruptThrottleRate to 3000 interrupts/sec for
the first, second, and third instances of the driver. The range
of 2000 to 3000 interrupts per second works on a majority of
systems and is a good starting point, but the optimal value will
be platform-specific. If CPU utilization is not a concern, use
RX_POLLING (NAPI) and default driver settings.
This sets the InterruptThrottleRate to 3000 interrupts/sec for the
first, second, and third instances of the driver. The range of 2000 to
3000 interrupts per second works on a majority of systems and is a
good starting point, but the optimal value will be platform-specific.
If CPU utilization is not a concern, use RX_POLLING (NAPI) and default
driver settings.
RxDescriptors
Valid Range: 80-256 for 82542 and 82543-based adapters
80-4096 for all other supported adapters
-------------
Valid Range: 80-256 for 82542 and 82543-based adapters
80-4096 for all other supported adapters
Default Value: 256
This value is the number of receive descriptors allocated by the driver.
Increasing this value allows the driver to buffer more incoming packets.
Each descriptor is 16 bytes. A receive buffer is allocated for each
descriptor and can either be 2048 or 4096 bytes long, depending on the MTU
setting. An incoming packet can span one or more receive descriptors.
The maximum MTU size is 16110.
This value specifies the number of receive descriptors allocated by the
driver. Increasing this value allows the driver to buffer more incoming
packets. Each descriptor is 16 bytes. A receive buffer is also
allocated for each descriptor and is 2048.
NOTE: MTU designates the frame size. It only needs to be set for Jumbo
Frames.
NOTE: Depending on the available system resources, the request for a
higher number of receive descriptors may be denied. In this case,
use a lower number.
RxIntDelay
Valid Range: 0-65535 (0=off)
----------
Valid Range: 0-65535 (0=off)
Default Value: 0
This value delays the generation of receive interrupts in units of 1.024
microseconds. Receive interrupt reduction can improve CPU efficiency if
properly tuned for specific network traffic. Increasing this value adds
extra latency to frame reception and can end up decreasing the throughput
of TCP traffic. If the system is reporting dropped receives, this value
may be set too high, causing the driver to run out of available receive
descriptors.
CAUTION: When setting RxIntDelay to a value other than 0, adapters may
hang (stop transmitting) under certain network conditions. If
this occurs a NETDEV WATCHDOG message is logged in the system
event log. In addition, the controller is automatically reset,
restoring the network connection. To eliminate the potential for
the hang ensure that RxIntDelay is set to 0.
This value delays the generation of receive interrupts in units of 1.024
microseconds. Receive interrupt reduction can improve CPU efficiency if
properly tuned for specific network traffic. Increasing this value adds
extra latency to frame reception and can end up decreasing the throughput
of TCP traffic. If the system is reporting dropped receives, this value
may be set too high, causing the driver to run out of available receive
descriptors.
RxAbsIntDelay (82540, 82545 and later adapters only)
Valid Range: 0-65535 (0=off)
CAUTION: When setting RxIntDelay to a value other than 0, adapters may
hang (stop transmitting) under certain network conditions. If
this occurs a NETDEV WATCHDOG message is logged in the system
event log. In addition, the controller is automatically reset,
restoring the network connection. To eliminate the potential
for the hang ensure that RxIntDelay is set to 0.
RxAbsIntDelay
-------------
(This parameter is supported only on 82540, 82545 and later adapters.)
Valid Range: 0-65535 (0=off)
Default Value: 128
This value, in units of 1.024 microseconds, limits the delay in which a
receive interrupt is generated. Useful only if RxIntDelay is non-zero,
this value ensures that an interrupt is generated after the initial
packet is received within the set amount of time. Proper tuning,
along with RxIntDelay, may improve traffic throughput in specific network
conditions.
Speed (adapters using copper connections only)
This value, in units of 1.024 microseconds, limits the delay in which a
receive interrupt is generated. Useful only if RxIntDelay is non-zero,
this value ensures that an interrupt is generated after the initial
packet is received within the set amount of time. Proper tuning,
along with RxIntDelay, may improve traffic throughput in specific network
conditions.
Speed
-----
(This parameter is supported only on adapters with copper connections.)
Valid Settings: 0, 10, 100, 1000
Default Value: 0 (auto-negotiate at all supported speeds)
Speed forces the line speed to the specified value in megabits per second
(Mbps). If this parameter is not specified or is set to 0 and the link
partner is set to auto-negotiate, the board will auto-detect the correct
speed. Duplex should also be set when Speed is set to either 10 or 100.
Default Value: 0 (auto-negotiate at all supported speeds)
Speed forces the line speed to the specified value in megabits per second
(Mbps). If this parameter is not specified or is set to 0 and the link
partner is set to auto-negotiate, the board will auto-detect the correct
speed. Duplex should also be set when Speed is set to either 10 or 100.
TxDescriptors
Valid Range: 80-256 for 82542 and 82543-based adapters
80-4096 for all other supported adapters
-------------
Valid Range: 80-256 for 82542 and 82543-based adapters
80-4096 for all other supported adapters
Default Value: 256
This value is the number of transmit descriptors allocated by the driver.
Increasing this value allows the driver to queue more transmits. Each
descriptor is 16 bytes.
NOTE: Depending on the available system resources, the request for a
higher number of transmit descriptors may be denied. In this case,
use a lower number.
This value is the number of transmit descriptors allocated by the driver.
Increasing this value allows the driver to queue more transmits. Each
descriptor is 16 bytes.
NOTE: Depending on the available system resources, the request for a
higher number of transmit descriptors may be denied. In this case,
use a lower number.
TxIntDelay
Valid Range: 0-65535 (0=off)
----------
Valid Range: 0-65535 (0=off)
Default Value: 64
This value delays the generation of transmit interrupts in units of
1.024 microseconds. Transmit interrupt reduction can improve CPU
efficiency if properly tuned for specific network traffic. If the
system is reporting dropped transmits, this value may be set too high
causing the driver to run out of available transmit descriptors.
TxAbsIntDelay (82540, 82545 and later adapters only)
Valid Range: 0-65535 (0=off)
This value delays the generation of transmit interrupts in units of
1.024 microseconds. Transmit interrupt reduction can improve CPU
efficiency if properly tuned for specific network traffic. If the
system is reporting dropped transmits, this value may be set too high
causing the driver to run out of available transmit descriptors.
TxAbsIntDelay
-------------
(This parameter is supported only on 82540, 82545 and later adapters.)
Valid Range: 0-65535 (0=off)
Default Value: 64
This value, in units of 1.024 microseconds, limits the delay in which a
transmit interrupt is generated. Useful only if TxIntDelay is non-zero,
this value ensures that an interrupt is generated after the initial
packet is sent on the wire within the set amount of time. Proper tuning,
along with TxIntDelay, may improve traffic throughput in specific
network conditions.
XsumRX (not available on the 82542-based adapter)
Valid Range: 0-1
This value, in units of 1.024 microseconds, limits the delay in which a
transmit interrupt is generated. Useful only if TxIntDelay is non-zero,
this value ensures that an interrupt is generated after the initial
packet is sent on the wire within the set amount of time. Proper tuning,
along with TxIntDelay, may improve traffic throughput in specific
network conditions.
XsumRX
------
(This parameter is NOT supported on the 82542-based adapter.)
Valid Range: 0-1
Default Value: 1
A value of '1' indicates that the driver should enable IP checksum
offload for received packets (both UDP and TCP) to the adapter hardware.
A value of '1' indicates that the driver should enable IP checksum
offload for received packets (both UDP and TCP) to the adapter hardware.
Speed and Duplex Configuration
==============================
Three keywords are used to control the speed and duplex configuration. These
keywords are Speed, Duplex, and AutoNeg.
Three keywords are used to control the speed and duplex configuration.
These keywords are Speed, Duplex, and AutoNeg.
If the board uses a fiber interface, these keywords are ignored, and the
If the board uses a fiber interface, these keywords are ignored, and the
fiber interface board only links at 1000 Mbps full-duplex.
For copper-based boards, the keywords interact as follows:
The default operation is auto-negotiate. The board advertises all supported
speed and duplex combinations, and it links at the highest common speed and
duplex mode IF the link partner is set to auto-negotiate.
The default operation is auto-negotiate. The board advertises all
supported speed and duplex combinations, and it links at the highest
common speed and duplex mode IF the link partner is set to auto-negotiate.
If Speed = 1000, limited auto-negotiation is enabled and only 1000 Mbps is
advertised (The 1000BaseT spec requires auto-negotiation.)
If Speed = 1000, limited auto-negotiation is enabled and only 1000 Mbps
is advertised (The 1000BaseT spec requires auto-negotiation.)
If Speed = 10 or 100, then both Speed and Duplex should be set. Auto-
negotiation is disabled, and the AutoNeg parameter is ignored. Partner SHOULD
also be forced.
negotiation is disabled, and the AutoNeg parameter is ignored. Partner
SHOULD also be forced.
The AutoNeg parameter is used when more control is required over the auto-
negotiation process. When this parameter is used, Speed and Duplex parameters
must not be specified. The following table describes supported values for the
AutoNeg parameter:
The AutoNeg parameter is used when more control is required over the
auto-negotiation process. It should be used when you wish to control which
speed and duplex combinations are advertised during the auto-negotiation
process.
Speed (Mbps) 1000 100 100 10 10
Duplex Full Full Half Full Half
Value (in base 16) 0x20 0x08 0x04 0x02 0x01
The parameter may be specified as either a decimal or hexidecimal value as
determined by the bitmap below.
Example: insmod e1000 AutoNeg=0x03, loads e1000 and specifies (10 full duplex,
10 half duplex) for negotiation with the peer.
Bit position 7 6 5 4 3 2 1 0
Decimal Value 128 64 32 16 8 4 2 1
Hex value 80 40 20 10 8 4 2 1
Speed (Mbps) N/A N/A 1000 N/A 100 100 10 10
Duplex Full Full Half Full Half
Note that setting AutoNeg does not guarantee that the board will link at the
highest specified speed or duplex mode, but the board will link at the
highest possible speed/duplex of the link partner IF the link partner is also
set to auto-negotiate. If the link partner is forced speed/duplex, the
adapter MUST be forced to the same speed/duplex.
Some examples of using AutoNeg:
modprobe e1000 AutoNeg=0x01 (Restricts autonegotiation to 10 Half)
modprobe e1000 AutoNeg=1 (Same as above)
modprobe e1000 AutoNeg=0x02 (Restricts autonegotiation to 10 Full)
modprobe e1000 AutoNeg=0x03 (Restricts autonegotiation to 10 Half or 10 Full)
modprobe e1000 AutoNeg=0x04 (Restricts autonegotiation to 100 Half)
modprobe e1000 AutoNeg=0x05 (Restricts autonegotiation to 10 Half or 100
Half)
modprobe e1000 AutoNeg=0x020 (Restricts autonegotiation to 1000 Full)
modprobe e1000 AutoNeg=32 (Same as above)
Note that when this parameter is used, Speed and Duplex must not be specified.
If the link partner is forced to a specific speed and duplex, then this
parameter should not be used. Instead, use the Speed and Duplex parameters
previously mentioned to force the adapter to the same speed and duplex.
Additional Configurations
@ -276,19 +338,19 @@ Additional Configurations
Configuring the Driver on Different Distributions
-------------------------------------------------
Configuring a network driver to load properly when the system is started is
distribution dependent. Typically, the configuration process involves adding
an alias line to /etc/modules.conf as well as editing other system startup
scripts and/or configuration files. Many popular Linux distributions ship
with tools to make these changes for you. To learn the proper way to
configure a network device for your system, refer to your distribution
documentation. If during this process you are asked for the driver or module
name, the name for the Linux Base Driver for the Intel PRO/1000 Family of
Adapters is e1000.
Configuring a network driver to load properly when the system is started
is distribution dependent. Typically, the configuration process involves
adding an alias line to /etc/modules.conf or /etc/modprobe.conf as well
as editing other system startup scripts and/or configuration files. Many
popular Linux distributions ship with tools to make these changes for you.
To learn the proper way to configure a network device for your system,
refer to your distribution documentation. If during this process you are
asked for the driver or module name, the name for the Linux Base Driver
for the Intel PRO/1000 Family of Adapters is e1000.
As an example, if you install the e1000 driver for two PRO/1000 adapters
(eth0 and eth1) and set the speed and duplex to 10full and 100half, add the
following to modules.conf:
As an example, if you install the e1000 driver for two PRO/1000 adapters
(eth0 and eth1) and set the speed and duplex to 10full and 100half, add
the following to modules.conf or or modprobe.conf:
alias eth0 e1000
alias eth1 e1000
@ -297,9 +359,9 @@ Additional Configurations
Viewing Link Messages
---------------------
Link messages will not be displayed to the console if the distribution is
restricting system messages. In order to see network driver link messages on
your console, set dmesg to eight by entering the following:
Link messages will not be displayed to the console if the distribution is
restricting system messages. In order to see network driver link messages
on your console, set dmesg to eight by entering the following:
dmesg -n 8
@ -308,22 +370,42 @@ Additional Configurations
Jumbo Frames
------------
The driver supports Jumbo Frames for all adapters except 82542-based
adapters. Jumbo Frames support is enabled by changing the MTU to a value
larger than the default of 1500. Use the ifconfig command to increase the
MTU size. For example:
The driver supports Jumbo Frames for all adapters except 82542 and
82573-based adapters. Jumbo Frames support is enabled by changing the
MTU to a value larger than the default of 1500. Use the ifconfig command
to increase the MTU size. For example:
ifconfig ethx mtu 9000 up
ifconfig eth<x> mtu 9000 up
The maximum MTU setting for Jumbo Frames is 16110. This value coincides
with the maximum Jumbo Frames size of 16128.
This setting is not saved across reboots. It can be made permanent if
you add:
NOTE: Jumbo Frames are supported at 1000 Mbps only. Using Jumbo Frames at
10 or 100 Mbps may result in poor performance or loss of link.
MTU=9000
to the file /etc/sysconfig/network-scripts/ifcfg-eth<x>. This example
applies to the Red Hat distributions; other distributions may store this
setting in a different location.
Notes:
- To enable Jumbo Frames, increase the MTU size on the interface beyond
1500.
- The maximum MTU setting for Jumbo Frames is 16110. This value coincides
with the maximum Jumbo Frames size of 16128.
- Using Jumbo Frames at 10 or 100 Mbps may result in poor performance or
loss of link.
- Some Intel gigabit adapters that support Jumbo Frames have a frame size
limit of 9238 bytes, with a corresponding MTU size limit of 9216 bytes.
The adapters with this limitation are based on the Intel 82571EB and
82572EI controllers, which correspond to these product names:
Intel® PRO/1000 PT Dual Port Server Adapter
Intel® PRO/1000 PF Dual Port Server Adapter
Intel® PRO/1000 PT Server Adapter
Intel® PRO/1000 PT Desktop Adapter
Intel® PRO/1000 PF Server Adapter
- The Intel PRO/1000 PM Network Connection does not support jumbo frames.
NOTE: MTU designates the frame size. To enable Jumbo Frames, increase the
MTU size on the interface beyond 1500.
Ethtool
-------
@ -333,32 +415,41 @@ Additional Configurations
version 1.6 or later is required for this functionality.
The latest release of ethtool can be found from
http://sf.net/projects/gkernel.
http://sourceforge.net/projects/gkernel.
NOTE: Ethtool 1.6 only supports a limited set of ethtool options. Support
for a more complete ethtool feature set can be enabled by upgrading
ethtool to ethtool-1.8.1.
NOTE: Ethtool 1.6 only supports a limited set of ethtool options. Support
for a more complete ethtool feature set can be enabled by upgrading
ethtool to ethtool-1.8.1.
Enabling Wake on LAN* (WoL)
---------------------------
WoL is configured through the Ethtool* utility. Ethtool is included with
all versions of Red Hat after Red Hat 7.2. For other Linux distributions,
download and install Ethtool from the following website:
all versions of Red Hat after Red Hat 7.2. For other Linux distributions,
download and install Ethtool from the following website:
http://sourceforge.net/projects/gkernel.
For instructions on enabling WoL with Ethtool, refer to the website listed
For instructions on enabling WoL with Ethtool, refer to the website listed
above.
WoL will be enabled on the system during the next shut down or reboot.
For this driver version, in order to enable WoL, the e1000 driver must be
WoL will be enabled on the system during the next shut down or reboot.
For this driver version, in order to enable WoL, the e1000 driver must be
loaded when shutting down or rebooting the system.
NAPI
----
NAPI (Rx polling mode) is supported in the e1000 driver. NAPI is enabled
or disabled based on the configuration of the kernel.
or disabled based on the configuration of the kernel. To override
the default, use the following compile-time flags.
To enable NAPI, compile the driver module, passing in a configuration option:
make CFLAGS_EXTRA=-DE1000_NAPI install
To disable NAPI, compile the driver module, passing in a configuration option:
make CFLAGS_EXTRA=-DE1000_NO_NAPI install
See www.cyberus.ca/~hadi/usenix-paper.tgz for more information on NAPI.
@ -369,10 +460,85 @@ Known Issues
Jumbo Frames System Requirement
-------------------------------
Memory allocation failures have been observed on Linux systems with 64 MB
of RAM or less that are running Jumbo Frames. If you are using Jumbo Frames,
your system may require more than the advertised minimum requirement of 64 MB
of system memory.
Memory allocation failures have been observed on Linux systems with 64 MB
of RAM or less that are running Jumbo Frames. If you are using Jumbo
Frames, your system may require more than the advertised minimum
requirement of 64 MB of system memory.
Performance Degradation with Jumbo Frames
-----------------------------------------
Degradation in throughput performance may be observed in some Jumbo frames
environments. If this is observed, increasing the application's socket
buffer size and/or increasing the /proc/sys/net/ipv4/tcp_*mem entry values
may help. See the specific application manual and
/usr/src/linux*/Documentation/
networking/ip-sysctl.txt for more details.
Jumbo frames on Foundry BigIron 8000 switch
-------------------------------------------
There is a known issue using Jumbo frames when connected to a Foundry
BigIron 8000 switch. This is a 3rd party limitation. If you experience
loss of packets, lower the MTU size.
Multiple Interfaces on Same Ethernet Broadcast Network
------------------------------------------------------
Due to the default ARP behavior on Linux, it is not possible to have
one system on two IP networks in the same Ethernet broadcast domain
(non-partitioned switch) behave as expected. All Ethernet interfaces
will respond to IP traffic for any IP address assigned to the system.
This results in unbalanced receive traffic.
If you have multiple interfaces in a server, either turn on ARP
filtering by entering:
echo 1 > /proc/sys/net/ipv4/conf/all/arp_filter
(this only works if your kernel's version is higher than 2.4.5),
NOTE: This setting is not saved across reboots. The configuration
change can be made permanent by adding the line:
net.ipv4.conf.all.arp_filter = 1
to the file /etc/sysctl.conf
or,
install the interfaces in separate broadcast domains (either in
different switches or in a switch partitioned to VLANs).
82541/82547 can't link or are slow to link with some link partners
-----------------------------------------------------------------
There is a known compatibility issue with 82541/82547 and some
low-end switches where the link will not be established, or will
be slow to establish. In particular, these switches are known to
be incompatible with 82541/82547:
Planex FXG-08TE
I-O Data ETG-SH8
To workaround this issue, the driver can be compiled with an override
of the PHY's master/slave setting. Forcing master or forcing slave
mode will improve time-to-link.
# make EXTRA_CFLAGS=-DE1000_MASTER_SLAVE=<n>
Where <n> is:
0 = Hardware default
1 = Master mode
2 = Slave mode
3 = Auto master/slave
Disable rx flow control with ethtool
------------------------------------
In order to disable receive flow control using ethtool, you must turn
off auto-negotiation on the same command line.
For example:
ethtool -A eth? autoneg off rx off
Support
@ -382,20 +548,24 @@ For general information, go to the Intel support website at:
http://support.intel.com
or the Intel Wired Networking project hosted by Sourceforge at:
http://sourceforge.net/projects/e1000
If an issue is identified with the released source code on the supported
kernel with a supported adapter, email the specific information related to
the issue to linux.nics@intel.com.
kernel with a supported adapter, email the specific information related
to the issue to e1000-devel@lists.sourceforge.net
License
=======
This software program is released under the terms of a license agreement
between you ('Licensee') and Intel. Do not use or load this software or any
associated materials (collectively, the 'Software') until you have carefully
read the full terms and conditions of the LICENSE located in this software
package. By loading or using the Software, you agree to the terms of this
Agreement. If you do not agree with the terms of this Agreement, do not
This software program is released under the terms of a license agreement
between you ('Licensee') and Intel. Do not use or load this software or any
associated materials (collectively, the 'Software') until you have carefully
read the full terms and conditions of the file COPYING located in this software
package. By loading or using the Software, you agree to the terms of this
Agreement. If you do not agree with the terms of this Agreement, do not
install or use the Software.
* Other names and brands may be claimed as the property of others.

16
MAINTAINERS
Просмотреть файл

@ -1349,10 +1349,10 @@ S: Maintained
INTEL PRO/100 ETHERNET SUPPORT
P: John Ronciak
M: john.ronciak@intel.com
P: Ganesh Venkatesan
M: ganesh.venkatesan@intel.com
P: Jesse Brandeburg
M: jesse.brandeburg@intel.com
P: Jeff Kirsher
M: jeffrey.t.kirsher@intel.com
W: http://sourceforge.net/projects/e1000/
S: Supported
@ -1361,18 +1361,22 @@ P: Jeb Cramer
M: cramerj@intel.com
P: John Ronciak
M: john.ronciak@intel.com
P: Ganesh Venkatesan
M: ganesh.venkatesan@intel.com
P: Jesse Brandeburg
M: jesse.brandeburg@intel.com
P: Jeff Kirsher
M: jeffrey.t.kirsher@intel.com
W: http://sourceforge.net/projects/e1000/
S: Supported
INTEL PRO/10GbE SUPPORT
P: Jeff Kirsher
M: jeffrey.t.kirsher@intel.com
P: Ayyappan Veeraiyan
M: ayyappan.veeraiyan@intel.com
P: Ganesh Venkatesan
M: ganesh.venkatesan@intel.com
P: John Ronciak
M: john.ronciak@intel.com
P: Jesse Brandeburg
M: jesse.brandeburg@intel.com
W: http://sourceforge.net/projects/e1000/
S: Supported