atl1c: update PHY reset related routine
Many magic data are re-configured for PHY during its reset operation based on chip type to get better compability and stability. REG_PHY_CTRL register may be configured by BIOS before enter OS. so, the driver can't directly write to it without any Read-Op. this change also affect suspend and phy_disable routines. PHY debug ports and extension registers are refined as well. Signed-off-by: xiong <xiong@qca.qualcomm.com> Tested-by: Liu David <dwliu@qca.qualcomm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
This commit is contained in:
Huang, Xiong
David S. Miller
Родитель
7c6c44f064
Коммит
ce5b972bc8
|
|
@ -457,6 +457,32 @@ int atl1c_write_phy_ext(struct atl1c_hw *hw, u8 dev_addr,
|
|||
return atl1c_write_phy_core(hw, true, dev_addr, reg_addr, phy_data);
|
||||
}
|
||||
|
||||
int atl1c_read_phy_dbg(struct atl1c_hw *hw, u16 reg_addr, u16 *phy_data)
|
||||
{
|
||||
int err;
|
||||
|
||||
err = atl1c_write_phy_reg(hw, MII_DBG_ADDR, reg_addr);
|
||||
if (unlikely(err))
|
||||
return err;
|
||||
else
|
||||
err = atl1c_read_phy_reg(hw, MII_DBG_DATA, phy_data);
|
||||
|
||||
return err;
|
||||
}
|
||||
|
||||
int atl1c_write_phy_dbg(struct atl1c_hw *hw, u16 reg_addr, u16 phy_data)
|
||||
{
|
||||
int err;
|
||||
|
||||
err = atl1c_write_phy_reg(hw, MII_DBG_ADDR, reg_addr);
|
||||
if (unlikely(err))
|
||||
return err;
|
||||
else
|
||||
err = atl1c_write_phy_reg(hw, MII_DBG_DATA, phy_data);
|
||||
|
||||
return err;
|
||||
}
|
||||
|
||||
/*
|
||||
* Configures PHY autoneg and flow control advertisement settings
|
||||
*
|
||||
|
|
@ -499,119 +525,107 @@ static int atl1c_phy_setup_adv(struct atl1c_hw *hw)
|
|||
|
||||
void atl1c_phy_disable(struct atl1c_hw *hw)
|
||||
{
|
||||
AT_WRITE_REGW(hw, REG_GPHY_CTRL,
|
||||
GPHY_CTRL_PW_WOL_DIS | GPHY_CTRL_EXT_RESET);
|
||||
u32 phy_ctrl_data;
|
||||
|
||||
AT_READ_REG(hw, REG_GPHY_CTRL, &phy_ctrl_data);
|
||||
phy_ctrl_data &= ~(GPHY_CTRL_EXT_RESET | GPHY_CTRL_CLS);
|
||||
phy_ctrl_data |= GPHY_CTRL_SEL_ANA_RST | GPHY_CTRL_HIB_PULSE |
|
||||
GPHY_CTRL_HIB_EN | GPHY_CTRL_PHY_IDDQ |
|
||||
GPHY_CTRL_PWDOWN_HW;
|
||||
AT_WRITE_REGW(hw, REG_GPHY_CTRL, phy_ctrl_data);
|
||||
}
|
||||
|
||||
static void atl1c_phy_magic_data(struct atl1c_hw *hw)
|
||||
{
|
||||
u16 data;
|
||||
|
||||
data = ANA_LOOP_SEL_10BT | ANA_EN_MASK_TB | ANA_EN_10BT_IDLE |
|
||||
((1 & ANA_INTERVAL_SEL_TIMER_MASK) <<
|
||||
ANA_INTERVAL_SEL_TIMER_SHIFT);
|
||||
|
||||
atl1c_write_phy_reg(hw, MII_DBG_ADDR, MII_ANA_CTRL_18);
|
||||
atl1c_write_phy_reg(hw, MII_DBG_DATA, data);
|
||||
|
||||
data = (2 & ANA_SERDES_CDR_BW_MASK) | ANA_MS_PAD_DBG |
|
||||
ANA_SERDES_EN_DEEM | ANA_SERDES_SEL_HSP | ANA_SERDES_EN_PLL |
|
||||
ANA_SERDES_EN_LCKDT;
|
||||
|
||||
atl1c_write_phy_reg(hw, MII_DBG_ADDR, MII_ANA_CTRL_5);
|
||||
atl1c_write_phy_reg(hw, MII_DBG_DATA, data);
|
||||
|
||||
data = (44 & ANA_LONG_CABLE_TH_100_MASK) |
|
||||
((33 & ANA_SHORT_CABLE_TH_100_MASK) <<
|
||||
ANA_SHORT_CABLE_TH_100_SHIFT) | ANA_BP_BAD_LINK_ACCUM |
|
||||
ANA_BP_SMALL_BW;
|
||||
|
||||
atl1c_write_phy_reg(hw, MII_DBG_ADDR, MII_ANA_CTRL_54);
|
||||
atl1c_write_phy_reg(hw, MII_DBG_DATA, data);
|
||||
|
||||
data = (11 & ANA_IECHO_ADJ_MASK) | ((11 & ANA_IECHO_ADJ_MASK) <<
|
||||
ANA_IECHO_ADJ_2_SHIFT) | ((8 & ANA_IECHO_ADJ_MASK) <<
|
||||
ANA_IECHO_ADJ_1_SHIFT) | ((8 & ANA_IECHO_ADJ_MASK) <<
|
||||
ANA_IECHO_ADJ_0_SHIFT);
|
||||
|
||||
atl1c_write_phy_reg(hw, MII_DBG_ADDR, MII_ANA_CTRL_4);
|
||||
atl1c_write_phy_reg(hw, MII_DBG_DATA, data);
|
||||
|
||||
data = ANA_RESTART_CAL | ((7 & ANA_MANUL_SWICH_ON_MASK) <<
|
||||
ANA_MANUL_SWICH_ON_SHIFT) | ANA_MAN_ENABLE |
|
||||
ANA_SEL_HSP | ANA_EN_HB | ANA_OEN_125M;
|
||||
|
||||
atl1c_write_phy_reg(hw, MII_DBG_ADDR, MII_ANA_CTRL_0);
|
||||
atl1c_write_phy_reg(hw, MII_DBG_DATA, data);
|
||||
|
||||
if (hw->ctrl_flags & ATL1C_HIB_DISABLE) {
|
||||
atl1c_write_phy_reg(hw, MII_DBG_ADDR, MII_ANA_CTRL_41);
|
||||
if (atl1c_read_phy_reg(hw, MII_DBG_DATA, &data) != 0)
|
||||
return;
|
||||
data &= ~ANA_TOP_PS_EN;
|
||||
atl1c_write_phy_reg(hw, MII_DBG_DATA, data);
|
||||
|
||||
atl1c_write_phy_reg(hw, MII_DBG_ADDR, MII_ANA_CTRL_11);
|
||||
if (atl1c_read_phy_reg(hw, MII_DBG_DATA, &data) != 0)
|
||||
return;
|
||||
data &= ~ANA_PS_HIB_EN;
|
||||
atl1c_write_phy_reg(hw, MII_DBG_DATA, data);
|
||||
}
|
||||
}
|
||||
|
||||
int atl1c_phy_reset(struct atl1c_hw *hw)
|
||||
{
|
||||
struct atl1c_adapter *adapter = hw->adapter;
|
||||
struct pci_dev *pdev = adapter->pdev;
|
||||
u16 phy_data;
|
||||
u32 phy_ctrl_data = GPHY_CTRL_DEFAULT;
|
||||
u32 mii_ier_data = IER_LINK_UP | IER_LINK_DOWN;
|
||||
u32 phy_ctrl_data, lpi_ctrl;
|
||||
int err;
|
||||
|
||||
if (hw->ctrl_flags & ATL1C_HIB_DISABLE)
|
||||
phy_ctrl_data &= ~GPHY_CTRL_HIB_EN;
|
||||
|
||||
/* reset PHY core */
|
||||
AT_READ_REG(hw, REG_GPHY_CTRL, &phy_ctrl_data);
|
||||
phy_ctrl_data &= ~(GPHY_CTRL_EXT_RESET | GPHY_CTRL_PHY_IDDQ |
|
||||
GPHY_CTRL_GATE_25M_EN | GPHY_CTRL_PWDOWN_HW | GPHY_CTRL_CLS);
|
||||
phy_ctrl_data |= GPHY_CTRL_SEL_ANA_RST;
|
||||
if (!(hw->ctrl_flags & ATL1C_HIB_DISABLE))
|
||||
phy_ctrl_data |= (GPHY_CTRL_HIB_EN | GPHY_CTRL_HIB_PULSE);
|
||||
else
|
||||
phy_ctrl_data &= ~(GPHY_CTRL_HIB_EN | GPHY_CTRL_HIB_PULSE);
|
||||
AT_WRITE_REG(hw, REG_GPHY_CTRL, phy_ctrl_data);
|
||||
AT_WRITE_FLUSH(hw);
|
||||
msleep(40);
|
||||
phy_ctrl_data |= GPHY_CTRL_EXT_RESET;
|
||||
AT_WRITE_REG(hw, REG_GPHY_CTRL, phy_ctrl_data);
|
||||
udelay(10);
|
||||
AT_WRITE_REG(hw, REG_GPHY_CTRL, phy_ctrl_data | GPHY_CTRL_EXT_RESET);
|
||||
AT_WRITE_FLUSH(hw);
|
||||
msleep(10);
|
||||
udelay(10 * GPHY_CTRL_EXT_RST_TO); /* delay 800us */
|
||||
|
||||
/* switch clock */
|
||||
if (hw->nic_type == athr_l2c_b) {
|
||||
atl1c_write_phy_reg(hw, MII_DBG_ADDR, 0x0A);
|
||||
atl1c_read_phy_reg(hw, MII_DBG_DATA, &phy_data);
|
||||
atl1c_write_phy_reg(hw, MII_DBG_DATA, phy_data & 0xDFFF);
|
||||
atl1c_read_phy_dbg(hw, MIIDBG_CFGLPSPD, &phy_data);
|
||||
atl1c_write_phy_dbg(hw, MIIDBG_CFGLPSPD,
|
||||
phy_data & ~CFGLPSPD_RSTCNT_CLK125SW);
|
||||
}
|
||||
|
||||
if (hw->nic_type == athr_l2c_b ||
|
||||
hw->nic_type == athr_l2c_b2 ||
|
||||
hw->nic_type == athr_l1d ||
|
||||
hw->nic_type == athr_l1d_2) {
|
||||
atl1c_write_phy_reg(hw, MII_DBG_ADDR, 0x3B);
|
||||
atl1c_read_phy_reg(hw, MII_DBG_DATA, &phy_data);
|
||||
atl1c_write_phy_reg(hw, MII_DBG_DATA, phy_data & 0xFFF7);
|
||||
msleep(20);
|
||||
/* tx-half amplitude issue fix */
|
||||
if (hw->nic_type == athr_l2c_b || hw->nic_type == athr_l2c_b2) {
|
||||
atl1c_read_phy_dbg(hw, MIIDBG_CABLE1TH_DET, &phy_data);
|
||||
phy_data |= CABLE1TH_DET_EN;
|
||||
atl1c_write_phy_dbg(hw, MIIDBG_CABLE1TH_DET, phy_data);
|
||||
}
|
||||
if (hw->nic_type == athr_l1d) {
|
||||
atl1c_write_phy_reg(hw, MII_DBG_ADDR, 0x29);
|
||||
atl1c_write_phy_reg(hw, MII_DBG_DATA, 0x929D);
|
||||
|
||||
/* clear bit3 of dbgport 3B to lower voltage */
|
||||
if (!(hw->ctrl_flags & ATL1C_HIB_DISABLE)) {
|
||||
if (hw->nic_type == athr_l2c_b || hw->nic_type == athr_l2c_b2) {
|
||||
atl1c_read_phy_dbg(hw, MIIDBG_VOLT_CTRL, &phy_data);
|
||||
phy_data &= ~VOLT_CTRL_SWLOWEST;
|
||||
atl1c_write_phy_dbg(hw, MIIDBG_VOLT_CTRL, phy_data);
|
||||
}
|
||||
/* power saving config */
|
||||
phy_data =
|
||||
hw->nic_type == athr_l1d || hw->nic_type == athr_l1d_2 ?
|
||||
L1D_LEGCYPS_DEF : L1C_LEGCYPS_DEF;
|
||||
atl1c_write_phy_dbg(hw, MIIDBG_LEGCYPS, phy_data);
|
||||
/* hib */
|
||||
atl1c_write_phy_dbg(hw, MIIDBG_SYSMODCTRL,
|
||||
SYSMODCTRL_IECHOADJ_DEF);
|
||||
} else {
|
||||
/* disable pws */
|
||||
atl1c_read_phy_dbg(hw, MIIDBG_LEGCYPS, &phy_data);
|
||||
atl1c_write_phy_dbg(hw, MIIDBG_LEGCYPS,
|
||||
phy_data & ~LEGCYPS_EN);
|
||||
/* disable hibernate */
|
||||
atl1c_read_phy_dbg(hw, MIIDBG_HIBNEG, &phy_data);
|
||||
atl1c_write_phy_dbg(hw, MIIDBG_HIBNEG,
|
||||
phy_data & HIBNEG_PSHIB_EN);
|
||||
}
|
||||
if (hw->nic_type == athr_l1c || hw->nic_type == athr_l2c_b2
|
||||
|| hw->nic_type == athr_l2c) {
|
||||
atl1c_write_phy_reg(hw, MII_DBG_ADDR, 0x29);
|
||||
atl1c_write_phy_reg(hw, MII_DBG_DATA, 0xB6DD);
|
||||
/* disable AZ(EEE) by default */
|
||||
if (hw->nic_type == athr_l1d || hw->nic_type == athr_l1d_2 ||
|
||||
hw->nic_type == athr_l2c_b2) {
|
||||
AT_READ_REG(hw, REG_LPI_CTRL, &lpi_ctrl);
|
||||
AT_WRITE_REG(hw, REG_LPI_CTRL, lpi_ctrl & ~LPI_CTRL_EN);
|
||||
atl1c_write_phy_ext(hw, MIIEXT_ANEG, MIIEXT_LOCAL_EEEADV, 0);
|
||||
atl1c_write_phy_ext(hw, MIIEXT_PCS, MIIEXT_CLDCTRL3,
|
||||
L2CB_CLDCTRL3);
|
||||
}
|
||||
err = atl1c_write_phy_reg(hw, MII_IER, mii_ier_data);
|
||||
|
||||
/* other debug port to set */
|
||||
atl1c_write_phy_dbg(hw, MIIDBG_ANACTRL, ANACTRL_DEF);
|
||||
atl1c_write_phy_dbg(hw, MIIDBG_SRDSYSMOD, SRDSYSMOD_DEF);
|
||||
atl1c_write_phy_dbg(hw, MIIDBG_TST10BTCFG, TST10BTCFG_DEF);
|
||||
/* UNH-IOL test issue, set bit7 */
|
||||
atl1c_write_phy_dbg(hw, MIIDBG_TST100BTCFG,
|
||||
TST100BTCFG_DEF | TST100BTCFG_LITCH_EN);
|
||||
|
||||
/* set phy interrupt mask */
|
||||
phy_data = IER_LINK_UP | IER_LINK_DOWN;
|
||||
err = atl1c_write_phy_reg(hw, MII_IER, phy_data);
|
||||
if (err) {
|
||||
if (netif_msg_hw(adapter))
|
||||
dev_err(&pdev->dev,
|
||||
"Error enable PHY linkChange Interrupt\n");
|
||||
return err;
|
||||
}
|
||||
if (!(hw->ctrl_flags & ATL1C_FPGA_VERSION))
|
||||
atl1c_phy_magic_data(hw);
|
||||
return 0;
|
||||
}
|
||||
|
||||
|
|
|
|||
|
|
@ -60,6 +60,9 @@ int atl1c_read_phy_ext(struct atl1c_hw *hw, u8 dev_addr,
|
|||
u16 reg_addr, u16 *phy_data);
|
||||
int atl1c_write_phy_ext(struct atl1c_hw *hw, u8 dev_addr,
|
||||
u16 reg_addr, u16 phy_data);
|
||||
int atl1c_read_phy_dbg(struct atl1c_hw *hw, u16 reg_addr, u16 *phy_data);
|
||||
int atl1c_write_phy_dbg(struct atl1c_hw *hw, u16 reg_addr, u16 phy_data);
|
||||
|
||||
/* register definition */
|
||||
#define REG_DEVICE_CAP 0x5C
|
||||
#define DEVICE_CAP_MAX_PAYLOAD_MASK 0x7
|
||||
|
|
@ -222,41 +225,32 @@ int atl1c_write_phy_ext(struct atl1c_hw *hw, u8 dev_addr,
|
|||
#define IRQ_MODRT_RX_TIMER_SHIFT 16
|
||||
|
||||
#define REG_GPHY_CTRL 0x140C
|
||||
#define GPHY_CTRL_EXT_RESET 0x1
|
||||
#define GPHY_CTRL_RTL_MODE 0x2
|
||||
#define GPHY_CTRL_LED_MODE 0x4
|
||||
#define GPHY_CTRL_ANEG_NOW 0x8
|
||||
#define GPHY_CTRL_REV_ANEG 0x10
|
||||
#define GPHY_CTRL_GATE_25M_EN 0x20
|
||||
#define GPHY_CTRL_LPW_EXIT 0x40
|
||||
#define GPHY_CTRL_PHY_IDDQ 0x80
|
||||
#define GPHY_CTRL_PHY_IDDQ_DIS 0x100
|
||||
#define GPHY_CTRL_GIGA_DIS 0x200
|
||||
#define GPHY_CTRL_HIB_EN 0x400
|
||||
#define GPHY_CTRL_HIB_PULSE 0x800
|
||||
#define GPHY_CTRL_SEL_ANA_RST 0x1000
|
||||
#define GPHY_CTRL_PHY_PLL_ON 0x2000
|
||||
#define GPHY_CTRL_PWDOWN_HW 0x4000
|
||||
#define GPHY_CTRL_PHY_PLL_BYPASS 0x8000
|
||||
|
||||
#define GPHY_CTRL_DEFAULT ( \
|
||||
GPHY_CTRL_SEL_ANA_RST |\
|
||||
GPHY_CTRL_HIB_PULSE |\
|
||||
GPHY_CTRL_HIB_EN)
|
||||
|
||||
#define GPHY_CTRL_PW_WOL_DIS ( \
|
||||
GPHY_CTRL_SEL_ANA_RST |\
|
||||
GPHY_CTRL_HIB_PULSE |\
|
||||
GPHY_CTRL_HIB_EN |\
|
||||
GPHY_CTRL_PWDOWN_HW |\
|
||||
GPHY_CTRL_PHY_IDDQ)
|
||||
|
||||
#define GPHY_CTRL_POWER_SAVING ( \
|
||||
GPHY_CTRL_SEL_ANA_RST |\
|
||||
GPHY_CTRL_HIB_EN |\
|
||||
GPHY_CTRL_HIB_PULSE |\
|
||||
GPHY_CTRL_PWDOWN_HW |\
|
||||
GPHY_CTRL_PHY_IDDQ)
|
||||
#define GPHY_CTRL_ADDR_MASK 0x1FUL
|
||||
#define GPHY_CTRL_ADDR_SHIFT 19
|
||||
#define GPHY_CTRL_BP_VLTGSW BIT(18)
|
||||
#define GPHY_CTRL_100AB_EN BIT(17)
|
||||
#define GPHY_CTRL_10AB_EN BIT(16)
|
||||
#define GPHY_CTRL_PHY_PLL_BYPASS BIT(15)
|
||||
#define GPHY_CTRL_PWDOWN_HW BIT(14) /* affect MAC&PHY, to low pw */
|
||||
#define GPHY_CTRL_PHY_PLL_ON BIT(13) /* 1:pll always on, 0:can sw */
|
||||
#define GPHY_CTRL_SEL_ANA_RST BIT(12)
|
||||
#define GPHY_CTRL_HIB_PULSE BIT(11)
|
||||
#define GPHY_CTRL_HIB_EN BIT(10)
|
||||
#define GPHY_CTRL_GIGA_DIS BIT(9)
|
||||
#define GPHY_CTRL_PHY_IDDQ_DIS BIT(8) /* pw on RST */
|
||||
#define GPHY_CTRL_PHY_IDDQ BIT(7) /* bit8 affect bit7 while rb */
|
||||
#define GPHY_CTRL_LPW_EXIT BIT(6)
|
||||
#define GPHY_CTRL_GATE_25M_EN BIT(5)
|
||||
#define GPHY_CTRL_REV_ANEG BIT(4)
|
||||
#define GPHY_CTRL_ANEG_NOW BIT(3)
|
||||
#define GPHY_CTRL_LED_MODE BIT(2)
|
||||
#define GPHY_CTRL_RTL_MODE BIT(1)
|
||||
#define GPHY_CTRL_EXT_RESET BIT(0) /* 1:out of DSP RST status */
|
||||
#define GPHY_CTRL_EXT_RST_TO 80 /* 800us atmost */
|
||||
#define GPHY_CTRL_CLS (\
|
||||
GPHY_CTRL_LED_MODE |\
|
||||
GPHY_CTRL_100AB_EN |\
|
||||
GPHY_CTRL_PHY_PLL_ON)
|
||||
|
||||
/* Block IDLE Status Register */
|
||||
#define REG_IDLE_STATUS 0x1410
|
||||
|
|
@ -350,6 +344,26 @@ int atl1c_write_phy_ext(struct atl1c_hw *hw, u8 dev_addr,
|
|||
#define SERDES_LOCK_DETECT_EN BIT(1)
|
||||
#define SERDES_LOCK_DETECT BIT(0)
|
||||
|
||||
#define REG_LPI_DECISN_TIMER 0x143C
|
||||
#define L2CB_LPI_DESISN_TIMER 0x7D00
|
||||
|
||||
#define REG_LPI_CTRL 0x1440
|
||||
#define LPI_CTRL_CHK_DA BIT(31)
|
||||
#define LPI_CTRL_ENH_TO_MASK 0x1FFFUL
|
||||
#define LPI_CTRL_ENH_TO_SHIFT 12
|
||||
#define LPI_CTRL_ENH_TH_MASK 0x1FUL
|
||||
#define LPI_CTRL_ENH_TH_SHIFT 6
|
||||
#define LPI_CTRL_ENH_EN BIT(5)
|
||||
#define LPI_CTRL_CHK_RX BIT(4)
|
||||
#define LPI_CTRL_CHK_STATE BIT(3)
|
||||
#define LPI_CTRL_GMII BIT(2)
|
||||
#define LPI_CTRL_TO_PHY BIT(1)
|
||||
#define LPI_CTRL_EN BIT(0)
|
||||
|
||||
#define REG_LPI_WAIT 0x1444
|
||||
#define LPI_WAIT_TIMER_MASK 0xFFFFUL
|
||||
#define LPI_WAIT_TIMER_SHIFT 0
|
||||
|
||||
/* MAC Control Register */
|
||||
#define REG_MAC_CTRL 0x1480
|
||||
#define MAC_CTRL_TX_EN 0x1
|
||||
|
|
@ -813,73 +827,188 @@ int atl1c_write_phy_ext(struct atl1c_hw *hw, u8 dev_addr,
|
|||
#define MII_DBG_ADDR 0x1D
|
||||
#define MII_DBG_DATA 0x1E
|
||||
|
||||
#define MII_ANA_CTRL_0 0x0
|
||||
#define ANA_RESTART_CAL 0x0001
|
||||
#define ANA_MANUL_SWICH_ON_SHIFT 0x1
|
||||
#define ANA_MANUL_SWICH_ON_MASK 0xF
|
||||
#define ANA_MAN_ENABLE 0x0020
|
||||
#define ANA_SEL_HSP 0x0040
|
||||
#define ANA_EN_HB 0x0080
|
||||
#define ANA_EN_HBIAS 0x0100
|
||||
#define ANA_OEN_125M 0x0200
|
||||
#define ANA_EN_LCKDT 0x0400
|
||||
#define ANA_LCKDT_PHY 0x0800
|
||||
#define ANA_AFE_MODE 0x1000
|
||||
#define ANA_VCO_SLOW 0x2000
|
||||
#define ANA_VCO_FAST 0x4000
|
||||
#define ANA_SEL_CLK125M_DSP 0x8000
|
||||
/***************************** debug port *************************************/
|
||||
|
||||
#define MII_ANA_CTRL_4 0x4
|
||||
#define ANA_IECHO_ADJ_MASK 0xF
|
||||
#define ANA_IECHO_ADJ_3_SHIFT 0
|
||||
#define ANA_IECHO_ADJ_2_SHIFT 4
|
||||
#define ANA_IECHO_ADJ_1_SHIFT 8
|
||||
#define ANA_IECHO_ADJ_0_SHIFT 12
|
||||
#define MIIDBG_ANACTRL 0x00
|
||||
#define ANACTRL_CLK125M_DELAY_EN 0x8000
|
||||
#define ANACTRL_VCO_FAST 0x4000
|
||||
#define ANACTRL_VCO_SLOW 0x2000
|
||||
#define ANACTRL_AFE_MODE_EN 0x1000
|
||||
#define ANACTRL_LCKDET_PHY 0x800
|
||||
#define ANACTRL_LCKDET_EN 0x400
|
||||
#define ANACTRL_OEN_125M 0x200
|
||||
#define ANACTRL_HBIAS_EN 0x100
|
||||
#define ANACTRL_HB_EN 0x80
|
||||
#define ANACTRL_SEL_HSP 0x40
|
||||
#define ANACTRL_CLASSA_EN 0x20
|
||||
#define ANACTRL_MANUSWON_SWR_MASK 3U
|
||||
#define ANACTRL_MANUSWON_SWR_SHIFT 2
|
||||
#define ANACTRL_MANUSWON_SWR_2V 0
|
||||
#define ANACTRL_MANUSWON_SWR_1P9V 1
|
||||
#define ANACTRL_MANUSWON_SWR_1P8V 2
|
||||
#define ANACTRL_MANUSWON_SWR_1P7V 3
|
||||
#define ANACTRL_MANUSWON_BW3_4M 0x2
|
||||
#define ANACTRL_RESTART_CAL 0x1
|
||||
#define ANACTRL_DEF 0x02EF
|
||||
|
||||
#define MII_ANA_CTRL_5 0x5
|
||||
#define ANA_SERDES_CDR_BW_SHIFT 0
|
||||
#define ANA_SERDES_CDR_BW_MASK 0x3
|
||||
#define ANA_MS_PAD_DBG 0x0004
|
||||
#define ANA_SPEEDUP_DBG 0x0008
|
||||
#define ANA_SERDES_TH_LOS_SHIFT 4
|
||||
#define ANA_SERDES_TH_LOS_MASK 0x3
|
||||
#define ANA_SERDES_EN_DEEM 0x0040
|
||||
#define ANA_SERDES_TXELECIDLE 0x0080
|
||||
#define ANA_SERDES_BEACON 0x0100
|
||||
#define ANA_SERDES_HALFTXDR 0x0200
|
||||
#define ANA_SERDES_SEL_HSP 0x0400
|
||||
#define ANA_SERDES_EN_PLL 0x0800
|
||||
#define ANA_SERDES_EN 0x1000
|
||||
#define ANA_SERDES_EN_LCKDT 0x2000
|
||||
#define MIIDBG_SYSMODCTRL 0x04
|
||||
#define SYSMODCTRL_IECHOADJ_PFMH_PHY 0x8000
|
||||
#define SYSMODCTRL_IECHOADJ_BIASGEN 0x4000
|
||||
#define SYSMODCTRL_IECHOADJ_PFML_PHY 0x2000
|
||||
#define SYSMODCTRL_IECHOADJ_PS_MASK 3U
|
||||
#define SYSMODCTRL_IECHOADJ_PS_SHIFT 10
|
||||
#define SYSMODCTRL_IECHOADJ_PS_40 3
|
||||
#define SYSMODCTRL_IECHOADJ_PS_20 2
|
||||
#define SYSMODCTRL_IECHOADJ_PS_0 1
|
||||
#define SYSMODCTRL_IECHOADJ_10BT_100MV 0x40 /* 1:100mv, 0:200mv */
|
||||
#define SYSMODCTRL_IECHOADJ_HLFAP_MASK 3U
|
||||
#define SYSMODCTRL_IECHOADJ_HLFAP_SHIFT 4
|
||||
#define SYSMODCTRL_IECHOADJ_VDFULBW 0x8
|
||||
#define SYSMODCTRL_IECHOADJ_VDBIASHLF 0x4
|
||||
#define SYSMODCTRL_IECHOADJ_VDAMPHLF 0x2
|
||||
#define SYSMODCTRL_IECHOADJ_VDLANSW 0x1
|
||||
#define SYSMODCTRL_IECHOADJ_DEF 0x88BB /* ???? */
|
||||
|
||||
#define MII_ANA_CTRL_11 0xB
|
||||
#define ANA_PS_HIB_EN 0x8000
|
||||
/* for l1d & l2cb */
|
||||
#define SYSMODCTRL_IECHOADJ_CUR_ADD 0x8000
|
||||
#define SYSMODCTRL_IECHOADJ_CUR_MASK 7U
|
||||
#define SYSMODCTRL_IECHOADJ_CUR_SHIFT 12
|
||||
#define SYSMODCTRL_IECHOADJ_VOL_MASK 0xFU
|
||||
#define SYSMODCTRL_IECHOADJ_VOL_SHIFT 8
|
||||
#define SYSMODCTRL_IECHOADJ_VOL_17ALL 3
|
||||
#define SYSMODCTRL_IECHOADJ_VOL_100M15 1
|
||||
#define SYSMODCTRL_IECHOADJ_VOL_10M17 0
|
||||
#define SYSMODCTRL_IECHOADJ_BIAS1_MASK 0xFU
|
||||
#define SYSMODCTRL_IECHOADJ_BIAS1_SHIFT 4
|
||||
#define SYSMODCTRL_IECHOADJ_BIAS2_MASK 0xFU
|
||||
#define SYSMODCTRL_IECHOADJ_BIAS2_SHIFT 0
|
||||
#define L1D_SYSMODCTRL_IECHOADJ_DEF 0x4FBB
|
||||
|
||||
#define MII_ANA_CTRL_18 0x12
|
||||
#define ANA_TEST_MODE_10BT_01SHIFT 0
|
||||
#define ANA_TEST_MODE_10BT_01MASK 0x3
|
||||
#define ANA_LOOP_SEL_10BT 0x0004
|
||||
#define ANA_RGMII_MODE_SW 0x0008
|
||||
#define ANA_EN_LONGECABLE 0x0010
|
||||
#define ANA_TEST_MODE_10BT_2 0x0020
|
||||
#define ANA_EN_10BT_IDLE 0x0400
|
||||
#define ANA_EN_MASK_TB 0x0800
|
||||
#define ANA_TRIGGER_SEL_TIMER_SHIFT 12
|
||||
#define ANA_TRIGGER_SEL_TIMER_MASK 0x3
|
||||
#define ANA_INTERVAL_SEL_TIMER_SHIFT 14
|
||||
#define ANA_INTERVAL_SEL_TIMER_MASK 0x3
|
||||
#define MIIDBG_SRDSYSMOD 0x05
|
||||
#define SRDSYSMOD_LCKDET_EN 0x2000
|
||||
#define SRDSYSMOD_PLL_EN 0x800
|
||||
#define SRDSYSMOD_SEL_HSP 0x400
|
||||
#define SRDSYSMOD_HLFTXDR 0x200
|
||||
#define SRDSYSMOD_TXCLK_DELAY_EN 0x100
|
||||
#define SRDSYSMOD_TXELECIDLE 0x80
|
||||
#define SRDSYSMOD_DEEMP_EN 0x40
|
||||
#define SRDSYSMOD_MS_PAD 0x4
|
||||
#define SRDSYSMOD_CDR_ADC_VLTG 0x2
|
||||
#define SRDSYSMOD_CDR_DAC_1MA 0x1
|
||||
#define SRDSYSMOD_DEF 0x2C46
|
||||
|
||||
#define MII_ANA_CTRL_41 0x29
|
||||
#define ANA_TOP_PS_EN 0x8000
|
||||
#define MIIDBG_CFGLPSPD 0x0A
|
||||
#define CFGLPSPD_RSTCNT_MASK 3U
|
||||
#define CFGLPSPD_RSTCNT_SHIFT 14
|
||||
#define CFGLPSPD_RSTCNT_CLK125SW 0x2000
|
||||
|
||||
#define MII_ANA_CTRL_54 0x36
|
||||
#define ANA_LONG_CABLE_TH_100_SHIFT 0
|
||||
#define ANA_LONG_CABLE_TH_100_MASK 0x3F
|
||||
#define ANA_DESERVED 0x0040
|
||||
#define ANA_EN_LIT_CH 0x0080
|
||||
#define ANA_SHORT_CABLE_TH_100_SHIFT 8
|
||||
#define ANA_SHORT_CABLE_TH_100_MASK 0x3F
|
||||
#define ANA_BP_BAD_LINK_ACCUM 0x4000
|
||||
#define ANA_BP_SMALL_BW 0x8000
|
||||
#define MIIDBG_HIBNEG 0x0B
|
||||
#define HIBNEG_PSHIB_EN 0x8000
|
||||
#define HIBNEG_WAKE_BOTH 0x4000
|
||||
#define HIBNEG_ONOFF_ANACHG_SUDEN 0x2000
|
||||
#define HIBNEG_HIB_PULSE 0x1000
|
||||
#define HIBNEG_GATE_25M_EN 0x800
|
||||
#define HIBNEG_RST_80U 0x400
|
||||
#define HIBNEG_RST_TIMER_MASK 3U
|
||||
#define HIBNEG_RST_TIMER_SHIFT 8
|
||||
#define HIBNEG_GTX_CLK_DELAY_MASK 3U
|
||||
#define HIBNEG_GTX_CLK_DELAY_SHIFT 5
|
||||
#define HIBNEG_BYPSS_BRKTIMER 0x10
|
||||
#define HIBNEG_DEF 0xBC40
|
||||
|
||||
#define MIIDBG_TST10BTCFG 0x12
|
||||
#define TST10BTCFG_INTV_TIMER_MASK 3U
|
||||
#define TST10BTCFG_INTV_TIMER_SHIFT 14
|
||||
#define TST10BTCFG_TRIGER_TIMER_MASK 3U
|
||||
#define TST10BTCFG_TRIGER_TIMER_SHIFT 12
|
||||
#define TST10BTCFG_DIV_MAN_MLT3_EN 0x800
|
||||
#define TST10BTCFG_OFF_DAC_IDLE 0x400
|
||||
#define TST10BTCFG_LPBK_DEEP 0x4 /* 1:deep,0:shallow */
|
||||
#define TST10BTCFG_DEF 0x4C04
|
||||
|
||||
#define MIIDBG_AZ_ANADECT 0x15
|
||||
#define AZ_ANADECT_10BTRX_TH 0x8000
|
||||
#define AZ_ANADECT_BOTH_01CHNL 0x4000
|
||||
#define AZ_ANADECT_INTV_MASK 0x3FU
|
||||
#define AZ_ANADECT_INTV_SHIFT 8
|
||||
#define AZ_ANADECT_THRESH_MASK 0xFU
|
||||
#define AZ_ANADECT_THRESH_SHIFT 4
|
||||
#define AZ_ANADECT_CHNL_MASK 0xFU
|
||||
#define AZ_ANADECT_CHNL_SHIFT 0
|
||||
#define AZ_ANADECT_DEF 0x3220
|
||||
#define AZ_ANADECT_LONG 0xb210
|
||||
|
||||
#define MIIDBG_MSE16DB 0x18 /* l1d */
|
||||
#define L1D_MSE16DB_UP 0x05EA
|
||||
#define L1D_MSE16DB_DOWN 0x02EA
|
||||
|
||||
#define MIIDBG_LEGCYPS 0x29
|
||||
#define LEGCYPS_EN 0x8000
|
||||
#define LEGCYPS_DAC_AMP1000_MASK 7U
|
||||
#define LEGCYPS_DAC_AMP1000_SHIFT 12
|
||||
#define LEGCYPS_DAC_AMP100_MASK 7U
|
||||
#define LEGCYPS_DAC_AMP100_SHIFT 9
|
||||
#define LEGCYPS_DAC_AMP10_MASK 7U
|
||||
#define LEGCYPS_DAC_AMP10_SHIFT 6
|
||||
#define LEGCYPS_UNPLUG_TIMER_MASK 7U
|
||||
#define LEGCYPS_UNPLUG_TIMER_SHIFT 3
|
||||
#define LEGCYPS_UNPLUG_DECT_EN 0x4
|
||||
#define LEGCYPS_ECNC_PS_EN 0x1
|
||||
#define L1D_LEGCYPS_DEF 0x129D
|
||||
#define L1C_LEGCYPS_DEF 0x36DD
|
||||
|
||||
#define MIIDBG_TST100BTCFG 0x36
|
||||
#define TST100BTCFG_NORMAL_BW_EN 0x8000
|
||||
#define TST100BTCFG_BADLNK_BYPASS 0x4000
|
||||
#define TST100BTCFG_SHORTCABL_TH_MASK 0x3FU
|
||||
#define TST100BTCFG_SHORTCABL_TH_SHIFT 8
|
||||
#define TST100BTCFG_LITCH_EN 0x80
|
||||
#define TST100BTCFG_VLT_SW 0x40
|
||||
#define TST100BTCFG_LONGCABL_TH_MASK 0x3FU
|
||||
#define TST100BTCFG_LONGCABL_TH_SHIFT 0
|
||||
#define TST100BTCFG_DEF 0xE12C
|
||||
|
||||
#define MIIDBG_VOLT_CTRL 0x3B /* only for l2cb 1 & 2 */
|
||||
#define VOLT_CTRL_CABLE1TH_MASK 0x1FFU
|
||||
#define VOLT_CTRL_CABLE1TH_SHIFT 7
|
||||
#define VOLT_CTRL_AMPCTRL_MASK 3U
|
||||
#define VOLT_CTRL_AMPCTRL_SHIFT 5
|
||||
#define VOLT_CTRL_SW_BYPASS 0x10
|
||||
#define VOLT_CTRL_SWLOWEST 0x8
|
||||
#define VOLT_CTRL_DACAMP10_MASK 7U
|
||||
#define VOLT_CTRL_DACAMP10_SHIFT 0
|
||||
|
||||
#define MIIDBG_CABLE1TH_DET 0x3E
|
||||
#define CABLE1TH_DET_EN 0x8000
|
||||
|
||||
|
||||
/******* dev 3 *********/
|
||||
#define MIIEXT_PCS 3
|
||||
|
||||
#define MIIEXT_CLDCTRL3 0x8003
|
||||
#define CLDCTRL3_BP_CABLE1TH_DET_GT 0x8000
|
||||
#define CLDCTRL3_AZ_DISAMP 0x1000
|
||||
#define L2CB_CLDCTRL3 0x4D19
|
||||
#define L1D_CLDCTRL3 0xDD19
|
||||
|
||||
#define MIIEXT_CLDCTRL6 0x8006
|
||||
#define CLDCTRL6_CAB_LEN_MASK 0x1FFU
|
||||
#define CLDCTRL6_CAB_LEN_SHIFT 0
|
||||
#define CLDCTRL6_CAB_LEN_SHORT 0x50
|
||||
|
||||
/********* dev 7 **********/
|
||||
#define MIIEXT_ANEG 7
|
||||
|
||||
#define MIIEXT_LOCAL_EEEADV 0x3C
|
||||
#define LOCAL_EEEADV_1000BT 0x4
|
||||
#define LOCAL_EEEADV_100BT 0x2
|
||||
|
||||
#define MIIEXT_REMOTE_EEEADV 0x3D
|
||||
#define REMOTE_EEEADV_1000BT 0x4
|
||||
#define REMOTE_EEEADV_100BT 0x2
|
||||
|
||||
#define MIIEXT_EEE_ANEG 0x8000
|
||||
#define EEE_ANEG_1000M 0x4
|
||||
#define EEE_ANEG_100M 0x2
|
||||
|
||||
#endif /*_ATL1C_HW_H_*/
|
||||
|
|
|
|||
|
|
@ -2314,6 +2314,7 @@ static int atl1c_suspend(struct device *dev)
|
|||
u32 wol_ctrl_data = 0;
|
||||
u16 mii_intr_status_data = 0;
|
||||
u32 wufc = adapter->wol;
|
||||
u32 phy_ctrl_data;
|
||||
|
||||
atl1c_disable_l0s_l1(hw);
|
||||
if (netif_running(netdev)) {
|
||||
|
|
@ -2328,6 +2329,7 @@ static int atl1c_suspend(struct device *dev)
|
|||
|
||||
AT_READ_REG(hw, REG_MASTER_CTRL, &master_ctrl_data);
|
||||
AT_READ_REG(hw, REG_MAC_CTRL, &mac_ctrl_data);
|
||||
AT_READ_REG(hw, REG_GPHY_CTRL, &phy_ctrl_data);
|
||||
|
||||
master_ctrl_data &= ~MASTER_CTRL_CLK_SEL_DIS;
|
||||
mac_ctrl_data &= ~(MAC_CTRL_PRMLEN_MASK << MAC_CTRL_PRMLEN_SHIFT);
|
||||
|
|
@ -2336,9 +2338,13 @@ static int atl1c_suspend(struct device *dev)
|
|||
MAC_CTRL_PRMLEN_SHIFT);
|
||||
mac_ctrl_data &= ~(MAC_CTRL_SPEED_MASK << MAC_CTRL_SPEED_SHIFT);
|
||||
mac_ctrl_data &= ~MAC_CTRL_DUPLX;
|
||||
phy_ctrl_data &= ~(GPHY_CTRL_EXT_RESET | GPHY_CTRL_CLS);
|
||||
phy_ctrl_data |= GPHY_CTRL_SEL_ANA_RST | GPHY_CTRL_HIB_PULSE |
|
||||
GPHY_CTRL_HIB_EN;
|
||||
|
||||
if (wufc) {
|
||||
mac_ctrl_data |= MAC_CTRL_RX_EN;
|
||||
phy_ctrl_data |= GPHY_CTRL_EXT_RESET;
|
||||
if (adapter->link_speed == SPEED_1000 ||
|
||||
adapter->link_speed == SPEED_0) {
|
||||
mac_ctrl_data |= atl1c_mac_speed_1000 <<
|
||||
|
|
@ -2381,23 +2387,20 @@ static int atl1c_suspend(struct device *dev)
|
|||
dev_dbg(&pdev->dev,
|
||||
"%s: suspend MAC=0x%x\n",
|
||||
atl1c_driver_name, mac_ctrl_data);
|
||||
AT_WRITE_REG(hw, REG_MASTER_CTRL, master_ctrl_data);
|
||||
AT_WRITE_REG(hw, REG_WOL_CTRL, wol_ctrl_data);
|
||||
AT_WRITE_REG(hw, REG_MAC_CTRL, mac_ctrl_data);
|
||||
|
||||
AT_WRITE_REG(hw, REG_GPHY_CTRL, GPHY_CTRL_DEFAULT |
|
||||
GPHY_CTRL_EXT_RESET);
|
||||
} else {
|
||||
AT_WRITE_REG(hw, REG_GPHY_CTRL, GPHY_CTRL_POWER_SAVING);
|
||||
master_ctrl_data |= MASTER_CTRL_CLK_SEL_DIS;
|
||||
mac_ctrl_data |= atl1c_mac_speed_10_100 << MAC_CTRL_SPEED_SHIFT;
|
||||
mac_ctrl_data |= MAC_CTRL_DUPLX;
|
||||
AT_WRITE_REG(hw, REG_MASTER_CTRL, master_ctrl_data);
|
||||
AT_WRITE_REG(hw, REG_MAC_CTRL, mac_ctrl_data);
|
||||
AT_WRITE_REG(hw, REG_WOL_CTRL, 0);
|
||||
phy_ctrl_data |= GPHY_CTRL_PHY_IDDQ | GPHY_CTRL_PWDOWN_HW;
|
||||
wol_ctrl_data = 0;
|
||||
hw->phy_configured = false; /* re-init PHY when resume */
|
||||
}
|
||||
|
||||
AT_WRITE_REG(hw, REG_MASTER_CTRL, master_ctrl_data);
|
||||
AT_WRITE_REG(hw, REG_MAC_CTRL, mac_ctrl_data);
|
||||
AT_WRITE_REG(hw, REG_GPHY_CTRL, phy_ctrl_data);
|
||||
AT_WRITE_REG(hw, REG_WOL_CTRL, wol_ctrl_data);
|
||||
|
||||
return 0;
|
||||
}
|
||||
|
||||
|
|
|
|||
Загрузка…
Ссылка в новой задаче