hwmon: add Corsair PSU HID controller driver

The Corsair digital power supplies of the series RMi, HXi and AXi include
a small micro-controller with a lot of sensors attached. The sensors can
be accessed by an USB connector from the outside.

This micro-controller provides the data by a simple proprietary USB HID
protocol. The data consist of temperatures, current and voltage levels,
power usage, uptimes, fan speed and some more. It is also possible to
configure the PSU (fan mode, mono/multi-rail, over current protection).

This driver provides access to the sensors/statistics of the RMi and HXi
series power supplies. It does not support configuring these devices,
because there would be many ways to misconfigure or even damage the PSU.

This patch adds:
- hwmon driver corsair-psu
- hwmon documentation
- updates MAINTAINERS

Signed-off-by: Wilken Gottwalt <wilken.gottwalt@posteo.net>
Link: https://lore.kernel.org/r/20201027131710.GA253280@monster.powergraphx.local
Signed-off-by: Guenter Roeck <linux@roeck-us.net>

Documentation/hwmon/corsair-psu.rst

@@ -0,0 +1,82 @@
+.. SPDX-License-Identifier: GPL-2.0-or-later
+
+Kernel driver corsair-psu
+=========================
+
+Supported devices:
+
+* Corsair Power Supplies
+
+  Corsair HX550i
+
+  Corsair HX650i
+
+  Corsair HX750i
+
+  Corsair HX850i
+
+  Corsair HX1000i
+
+  Corsair HX1200i
+
+  Corsair RM550i
+
+  Corsair RM650i
+
+  Corsair RM750i
+
+  Corsair RM850i
+
+  Corsair RM1000i
+
+Author: Wilken Gottwalt
+
+Description
+-----------
+
+This driver implements the sysfs interface for the Corsair PSUs with a HID protocol
+interface of the HXi and RMi series.
+These power supplies provide access to a micro-controller with 2 attached
+temperature sensors, 1 fan rpm sensor, 4 sensors for volt levels, 4 sensors for
+power usage and 4 sensors for current levels and addtional non-sensor information
+like uptimes.
+
+Sysfs entries
+-------------
+
+=======================	========================================================
+curr1_input		Total current usage
+curr2_input		Current on the 12v psu rail
+curr3_input		Current on the 5v psu rail
+curr4_input		Current on the 3.3v psu rail
+fan1_input		RPM of psu fan
+in0_input		Voltage of the psu ac input
+in1_input		Voltage of the 12v psu rail
+in2_input		Voltage of the 5v psu rail
+in3_input		Voltage of the 3.3 psu rail
+power1_input		Total power usage
+power2_input		Power usage of the 12v psu rail
+power3_input		Power usage of the 5v psu rail
+power4_input		Power usage of the 3.3v psu rail
+temp1_input		Temperature of the psu vrm component
+temp2_input		Temperature of the psu case
+=======================	========================================================
+
+Usage Notes
+-----------
+
+It is an USB HID device, so it is auto-detected and supports hot-swapping.
+
+Flickering values in the rail voltage levels can be an indicator for a failing
+PSU. The driver also provides some additional useful values via debugfs, which
+do not fit into the hwmon class.
+
+Debugfs entries
+---------------
+
+=======================	========================================================
+uptime			Current uptime of the psu
+uptime_total		Total uptime of the psu
+vendor			Vendor name of the psu
+product			Product name of the psu
+=======================	========================================================

Documentation/hwmon/index.rst

@@ -49,6 +49,7 @@ Hardware Monitoring Kernel Drivers
    bt1-pvt
    coretemp
    corsair-cpro
+   corsair-psu
    da9052
    da9055
    dell-smm-hwmon

MAINTAINERS

@@ -4485,6 +4485,13 @@ L:	linux-hwmon@vger.kernel.org
 S:	Maintained
 F:	drivers/hwmon/corsair-cpro.c
 
+CORSAIR-PSU HARDWARE MONITOR DRIVER
+M:	Wilken Gottwalt <wilken.gottwalt@posteo.net>
+L:	linux-hwmon@vger.kernel.org
+S:	Maintained
+F:	Documentation/hwmon/corsair-psu.rst
+F:	drivers/hwmon/corsair-psu.c
+
 COSA/SRP SYNC SERIAL DRIVER
 M:	Jan "Yenya" Kasprzak <kas@fi.muni.cz>
 S:	Maintained

drivers/hwmon/Kconfig

@@ -449,6 +449,19 @@ config SENSORS_CORSAIR_CPRO
 	  This driver can also be built as a module. If so, the module
 	  will be called corsair-cpro.
 
+config SENSORS_CORSAIR_PSU
+	tristate "Corsair PSU HID controller"
+	depends on HID
+	help
+	  If you say yes here you get support for Corsair PSUs with a HID
+	  interface.
+	  Currently this driver supports the (RM/HX)550i, (RM/HX)650i,
+	  (RM/HX)750i, (RM/HX)850i, (RM/HX)1000i and HX1200i power supplies
+	  by Corsair.
+
+	  This driver can also be built as a module. If so, the module
+	  will be called corsair-psu.
+
 config SENSORS_DRIVETEMP
 	tristate "Hard disk drives with temperature sensors"
 	depends on SCSI && ATA

drivers/hwmon/Makefile

@@ -57,6 +57,7 @@ obj-$(CONFIG_SENSORS_AXI_FAN_CONTROL) += axi-fan-control.o
 obj-$(CONFIG_SENSORS_BT1_PVT)	+= bt1-pvt.o
 obj-$(CONFIG_SENSORS_CORETEMP)	+= coretemp.o
 obj-$(CONFIG_SENSORS_CORSAIR_CPRO) += corsair-cpro.o
+obj-$(CONFIG_SENSORS_CORSAIR_PSU) += corsair-psu.o
 obj-$(CONFIG_SENSORS_DA9052_ADC)+= da9052-hwmon.o
 obj-$(CONFIG_SENSORS_DA9055)+= da9055-hwmon.o
 obj-$(CONFIG_SENSORS_DELL_SMM)	+= dell-smm-hwmon.o

drivers/hwmon/corsair-psu.c

@@ -0,0 +1,605 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * corsair-psu.c - Linux driver for Corsair power supplies with HID sensors interface
+ * Copyright (C) 2020 Wilken Gottwalt <wilken.gottwalt@posteo.net>
+ */
+
+#include <linux/completion.h>
+#include <linux/debugfs.h>
+#include <linux/errno.h>
+#include <linux/hid.h>
+#include <linux/hwmon.h>
+#include <linux/hwmon-sysfs.h>
+#include <linux/jiffies.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/mutex.h>
+#include <linux/slab.h>
+#include <linux/types.h>
+
+/*
+ * Corsair protocol for PSUs
+ *
+ * message size = 64 bytes (request and response, little endian)
+ * request:
+ *	[length][command][param0][param1][paramX]...
+ * reply:
+ *	[echo of length][echo of command][data0][data1][dataX]...
+ *
+ *	- commands are byte sized opcodes
+ *	- length is the sum of all bytes of the commands/params
+ *	- the micro-controller of most of these PSUs support concatenation in the request and reply,
+ *	  but it is better to not rely on this (it is also hard to parse)
+ *	- the driver uses raw events to be accessible from userspace (though this is not really
+ *	  supported, it is just there for convenience, may be removed in the future)
+ *	- a reply always start with the length and command in the same order the request used it
+ *	- length of the reply data is specific to the command used
+ *	- some of the commands work on a rail and can be switched to a specific rail (0 = 12v,
+ *	  1 = 5v, 2 = 3.3v)
+ *	- the format of the init command 0xFE is swapped length/command bytes
+ *	- parameter bytes amount and values are specific to the command (rail setting is the only
+ *	  for now that uses non-zero values)
+ *	- there are much more commands, especially for configuring the device, but they are not
+ *	  supported because a wrong command/length can lockup the micro-controller
+ *	- the driver supports debugfs for values not fitting into the hwmon class
+ *	- not every device class (HXi, RMi or AXi) supports all commands
+ *	- it is a pure sensors reading driver (will not support configuring)
+ */
+
+#define DRIVER_NAME		"corsair-psu"
+
+#define REPLY_SIZE		16 /* max length of a reply to a single command */
+#define CMD_BUFFER_SIZE		64
+#define CMD_TIMEOUT_MS		250
+#define SECONDS_PER_HOUR	(60 * 60)
+#define SECONDS_PER_DAY		(SECONDS_PER_HOUR * 24)
+
+#define PSU_CMD_SELECT_RAIL	0x00 /* expects length 2 */
+#define PSU_CMD_IN_VOLTS	0x88 /* the rest of the commands expect length 3 */
+#define PSU_CMD_IN_AMPS		0x89
+#define PSU_CMD_RAIL_OUT_VOLTS	0x8B
+#define PSU_CMD_RAIL_AMPS	0x8C
+#define PSU_CMD_TEMP0		0x8D
+#define PSU_CMD_TEMP1		0x8E
+#define PSU_CMD_FAN		0x90
+#define PSU_CMD_RAIL_WATTS	0x96
+#define PSU_CMD_VEND_STR	0x99
+#define PSU_CMD_PROD_STR	0x9A
+#define PSU_CMD_TOTAL_WATTS	0xEE
+#define PSU_CMD_TOTAL_UPTIME	0xD1
+#define PSU_CMD_UPTIME		0xD2
+#define PSU_CMD_INIT		0xFE
+
+#define L_IN_VOLTS		"v_in"
+#define L_OUT_VOLTS_12V		"v_out +12v"
+#define L_OUT_VOLTS_5V		"v_out +5v"
+#define L_OUT_VOLTS_3_3V	"v_out +3.3v"
+#define L_IN_AMPS		"curr in"
+#define L_AMPS_12V		"curr +12v"
+#define L_AMPS_5V		"curr +5v"
+#define L_AMPS_3_3V		"curr +3.3v"
+#define L_FAN			"psu fan"
+#define L_TEMP0			"vrm temp"
+#define L_TEMP1			"case temp"
+#define L_WATTS			"power total"
+#define L_WATTS_12V		"power +12v"
+#define L_WATTS_5V		"power +5v"
+#define L_WATTS_3_3V		"power +3.3v"
+
+static const char *const label_watts[] = {
+	L_WATTS,
+	L_WATTS_12V,
+	L_WATTS_5V,
+	L_WATTS_3_3V
+};
+
+static const char *const label_volts[] = {
+	L_IN_VOLTS,
+	L_OUT_VOLTS_12V,
+	L_OUT_VOLTS_5V,
+	L_OUT_VOLTS_3_3V
+};
+
+static const char *const label_amps[] = {
+	L_IN_AMPS,
+	L_AMPS_12V,
+	L_AMPS_5V,
+	L_AMPS_3_3V
+};
+
+struct corsairpsu_data {
+	struct hid_device *hdev;
+	struct device *hwmon_dev;
+	struct dentry *debugfs;
+	struct completion wait_completion;
+	struct mutex lock; /* for locking access to cmd_buffer */
+	u8 *cmd_buffer;
+	char vendor[REPLY_SIZE];
+	char product[REPLY_SIZE];
+};
+
+/* some values are SMBus LINEAR11 data which need a conversion */
+static int corsairpsu_linear11_to_int(const int val)
+{
+	int exp = (val & 0xFFFF) >> 0x0B;
+	int mant = val & 0x7FF;
+	int i;
+
+	if (exp > 0x0F)
+		exp -= 0x20;
+	if (mant > 0x3FF)
+		mant -= 0x800;
+	if ((mant & 0x01) == 1)
+		++mant;
+	if (exp < 0) {
+		for (i = 0; i < -exp; ++i)
+			mant /= 2;
+	} else {
+		for (i = 0; i < exp; ++i)
+			mant *= 2;
+	}
+
+	return mant;
+}
+
+static int corsairpsu_usb_cmd(struct corsairpsu_data *priv, u8 p0, u8 p1, u8 p2, void *data)
+{
+	unsigned long time;
+	int ret;
+
+	memset(priv->cmd_buffer, 0, CMD_BUFFER_SIZE);
+	priv->cmd_buffer[0] = p0;
+	priv->cmd_buffer[1] = p1;
+	priv->cmd_buffer[2] = p2;
+
+	reinit_completion(&priv->wait_completion);
+
+	ret = hid_hw_output_report(priv->hdev, priv->cmd_buffer, CMD_BUFFER_SIZE);
+	if (ret < 0)
+		return ret;
+
+	time = wait_for_completion_timeout(&priv->wait_completion,
+					   msecs_to_jiffies(CMD_TIMEOUT_MS));
+	if (!time)
+		return -ETIMEDOUT;
+
+	/*
+	 * at the start of the reply is an echo of the send command/length in the same order it
+	 * was send, not every command is supported on every device class, if a command is not
+	 * supported, the length value in the reply is okay, but the command value is set to 0
+	 */
+	if (p0 != priv->cmd_buffer[0] || p1 != priv->cmd_buffer[1])
+		return -EOPNOTSUPP;
+
+	if (data)
+		memcpy(data, priv->cmd_buffer + 2, REPLY_SIZE);
+
+	return 0;
+}
+
+static int corsairpsu_init(struct corsairpsu_data *priv)
+{
+	/*
+	 * PSU_CMD_INIT uses swapped length/command and expects 2 parameter bytes, this command
+	 * actually generates a reply, but we don't need it
+	 */
+	return corsairpsu_usb_cmd(priv, PSU_CMD_INIT, 3, 0, NULL);
+}
+
+static int corsairpsu_fwinfo(struct corsairpsu_data *priv)
+{
+	int ret;
+
+	ret = corsairpsu_usb_cmd(priv, 3, PSU_CMD_VEND_STR, 0, priv->vendor);
+	if (ret < 0)
+		return ret;
+
+	ret = corsairpsu_usb_cmd(priv, 3, PSU_CMD_PROD_STR, 0, priv->product);
+	if (ret < 0)
+		return ret;
+
+	return 0;
+}
+
+static int corsairpsu_request(struct corsairpsu_data *priv, u8 cmd, u8 rail, void *data)
+{
+	int ret;
+
+	mutex_lock(&priv->lock);
+	switch (cmd) {
+	case PSU_CMD_RAIL_OUT_VOLTS:
+	case PSU_CMD_RAIL_AMPS:
+	case PSU_CMD_RAIL_WATTS:
+		ret = corsairpsu_usb_cmd(priv, 2, PSU_CMD_SELECT_RAIL, rail, NULL);
+		if (ret < 0)
+			goto cmd_fail;
+		break;
+	default:
+		break;
+	}
+
+	ret = corsairpsu_usb_cmd(priv, 3, cmd, 0, data);
+
+cmd_fail:
+	mutex_unlock(&priv->lock);
+	return ret;
+}
+
+static int corsairpsu_get_value(struct corsairpsu_data *priv, u8 cmd, u8 rail, long *val)
+{
+	u8 data[REPLY_SIZE];
+	long tmp;
+	int ret;
+
+	ret = corsairpsu_request(priv, cmd, rail, data);
+	if (ret < 0)
+		return ret;
+
+	/*
+	 * the biggest value here comes from the uptime command and to exceed MAXINT total uptime
+	 * needs to be about 68 years, the rest are u16 values and the biggest value coming out of
+	 * the LINEAR11 conversion are the watts values which are about 1200 for the strongest psu
+	 * supported (HX1200i)
+	 */
+	tmp = (data[3] << 24) + (data[2] << 16) + (data[1] << 8) + data[0];
+	switch (cmd) {
+	case PSU_CMD_IN_VOLTS:
+	case PSU_CMD_IN_AMPS:
+	case PSU_CMD_RAIL_OUT_VOLTS:
+	case PSU_CMD_RAIL_AMPS:
+	case PSU_CMD_TEMP0:
+	case PSU_CMD_TEMP1:
+		*val = corsairpsu_linear11_to_int(tmp & 0xFFFF) * 1000;
+		break;
+	case PSU_CMD_FAN:
+		/*
+		 * this value is best guess, so the calculated value could be wrong, it is hard
+		 * to ge the fan to spin in these semi-passive power supplies, which need a
+		 * quite high load to do so
+		 */
+		*val = ((tmp & 0xFF) << 8) + ((tmp >> 8) & 0xFF);
+		break;
+	case PSU_CMD_RAIL_WATTS:
+	case PSU_CMD_TOTAL_WATTS:
+		*val = corsairpsu_linear11_to_int(tmp & 0xFFFF) * 1000000;
+		break;
+	case PSU_CMD_TOTAL_UPTIME:
+	case PSU_CMD_UPTIME:
+		*val = tmp;
+		break;
+	default:
+		ret = -EOPNOTSUPP;
+		break;
+	}
+
+	return ret;
+}
+
+static umode_t corsairpsu_hwmon_ops_is_visible(const void *data, enum hwmon_sensor_types type,
+					       u32 attr, int channel)
+{
+	if (type == hwmon_temp && (attr == hwmon_temp_input || attr == hwmon_temp_label))
+		return 0444;
+	else if (type == hwmon_fan && (attr == hwmon_fan_input || attr == hwmon_fan_label))
+		return 0444;
+	else if (type == hwmon_power && (attr == hwmon_power_input || attr == hwmon_power_label))
+		return 0444;
+	else if (type == hwmon_in && (attr == hwmon_in_input || attr == hwmon_in_label))
+		return 0444;
+	else if (type == hwmon_curr && (attr == hwmon_curr_input || attr == hwmon_curr_label))
+		return 0444;
+
+	return 0;
+}
+
+static int corsairpsu_hwmon_ops_read(struct device *dev, enum hwmon_sensor_types type, u32 attr,
+				     int channel, long *val)
+{
+	struct corsairpsu_data *priv = dev_get_drvdata(dev);
+	int ret;
+
+	if (type == hwmon_temp && attr == hwmon_temp_input && channel < 2) {
+		ret = corsairpsu_get_value(priv, channel ? PSU_CMD_TEMP1 : PSU_CMD_TEMP0, channel,
+					   val);
+	} else if (type == hwmon_fan && attr == hwmon_fan_input) {
+		ret = corsairpsu_get_value(priv, PSU_CMD_FAN, 0, val);
+	} else if (type == hwmon_power && attr == hwmon_power_input) {
+		switch (channel) {
+		case 0:
+			ret = corsairpsu_get_value(priv, PSU_CMD_TOTAL_WATTS, 0, val);
+			break;
+		case 1 ... 3:
+			ret = corsairpsu_get_value(priv, PSU_CMD_RAIL_WATTS, channel - 1, val);
+			break;
+		default:
+			return -EOPNOTSUPP;
+		}
+	} else if (type == hwmon_in && attr == hwmon_in_input) {
+		switch (channel) {
+		case 0:
+			ret = corsairpsu_get_value(priv, PSU_CMD_IN_VOLTS, 0, val);
+			break;
+		case 1 ... 3:
+			ret = corsairpsu_get_value(priv, PSU_CMD_RAIL_OUT_VOLTS, channel - 1, val);
+			break;
+		default:
+			return -EOPNOTSUPP;
+		}
+	} else if (type == hwmon_curr && attr == hwmon_curr_input) {
+		switch (channel) {
+		case 0:
+			ret = corsairpsu_get_value(priv, PSU_CMD_IN_AMPS, 0, val);
+			break;
+		case 1 ... 3:
+			ret = corsairpsu_get_value(priv, PSU_CMD_RAIL_AMPS, channel - 1, val);
+			break;
+		default:
+			return -EOPNOTSUPP;
+		}
+	} else {
+		return -EOPNOTSUPP;
+	}
+
+	if (ret < 0)
+		return ret;
+
+	return 0;
+}
+
+static int corsairpsu_hwmon_ops_read_string(struct device *dev, enum hwmon_sensor_types type,
+					    u32 attr, int channel, const char **str)
+{
+	if (type == hwmon_temp && attr == hwmon_temp_label) {
+		*str = channel ? L_TEMP1 : L_TEMP0;
+		return 0;
+	} else if (type == hwmon_fan && attr == hwmon_fan_label) {
+		*str = L_FAN;
+		return 0;
+	} else if (type == hwmon_power && attr == hwmon_power_label && channel < 4) {
+		*str = label_watts[channel];
+		return 0;
+	} else if (type == hwmon_in && attr == hwmon_in_label && channel < 4) {
+		*str = label_volts[channel];
+		return 0;
+	} else if (type == hwmon_curr && attr == hwmon_curr_label && channel < 4) {
+		*str = label_amps[channel];
+		return 0;
+	}
+
+	return -EOPNOTSUPP;
+}
+
+static const struct hwmon_ops corsairpsu_hwmon_ops = {
+	.is_visible	= corsairpsu_hwmon_ops_is_visible,
+	.read		= corsairpsu_hwmon_ops_read,
+	.read_string	= corsairpsu_hwmon_ops_read_string,
+};
+
+static const struct hwmon_channel_info *corsairpsu_info[] = {
+	HWMON_CHANNEL_INFO(chip,
+			   HWMON_C_REGISTER_TZ),
+	HWMON_CHANNEL_INFO(temp,
+			   HWMON_T_INPUT | HWMON_T_LABEL,
+			   HWMON_T_INPUT | HWMON_T_LABEL),
+	HWMON_CHANNEL_INFO(fan,
+			   HWMON_F_INPUT | HWMON_F_LABEL),
+	HWMON_CHANNEL_INFO(power,
+			   HWMON_P_INPUT | HWMON_P_LABEL,
+			   HWMON_P_INPUT | HWMON_P_LABEL,
+			   HWMON_P_INPUT | HWMON_P_LABEL,
+			   HWMON_P_INPUT | HWMON_P_LABEL),
+	HWMON_CHANNEL_INFO(in,
+			   HWMON_I_INPUT | HWMON_I_LABEL,
+			   HWMON_I_INPUT | HWMON_I_LABEL,
+			   HWMON_I_INPUT | HWMON_I_LABEL,
+			   HWMON_I_INPUT | HWMON_I_LABEL),
+	HWMON_CHANNEL_INFO(curr,
+			   HWMON_C_INPUT | HWMON_C_LABEL,
+			   HWMON_C_INPUT | HWMON_C_LABEL,
+			   HWMON_C_INPUT | HWMON_C_LABEL,
+			   HWMON_C_INPUT | HWMON_C_LABEL),
+	NULL
+};
+
+static const struct hwmon_chip_info corsairpsu_chip_info = {
+	.ops	= &corsairpsu_hwmon_ops,
+	.info	= corsairpsu_info,
+};
+
+#ifdef CONFIG_DEBUG_FS
+
+static void print_uptime(struct seq_file *seqf, u8 cmd)
+{
+	struct corsairpsu_data *priv = seqf->private;
+	long val;
+	int ret;
+
+	ret = corsairpsu_get_value(priv, cmd, 0, &val);
+	if (ret < 0) {
+		seq_puts(seqf, "N/A\n");
+		return;
+	}
+
+	if (val > SECONDS_PER_DAY) {
+		seq_printf(seqf, "%ld day(s), %02ld:%02ld:%02ld\n", val / SECONDS_PER_DAY,
+			   val % SECONDS_PER_DAY / SECONDS_PER_HOUR, val % SECONDS_PER_HOUR / 60,
+			   val % 60);
+		return;
+	}
+
+	seq_printf(seqf, "%02ld:%02ld:%02ld\n", val % SECONDS_PER_DAY / SECONDS_PER_HOUR,
+		   val % SECONDS_PER_HOUR / 60, val % 60);
+}
+
+static int uptime_show(struct seq_file *seqf, void *unused)
+{
+	print_uptime(seqf, PSU_CMD_UPTIME);
+
+	return 0;
+}
+DEFINE_SHOW_ATTRIBUTE(uptime);
+
+static int uptime_total_show(struct seq_file *seqf, void *unused)
+{
+	print_uptime(seqf, PSU_CMD_TOTAL_UPTIME);
+
+	return 0;
+}
+DEFINE_SHOW_ATTRIBUTE(uptime_total);
+
+static int vendor_show(struct seq_file *seqf, void *unused)
+{
+	struct corsairpsu_data *priv = seqf->private;
+
+	seq_printf(seqf, "%s\n", priv->vendor);
+
+	return 0;
+}
+DEFINE_SHOW_ATTRIBUTE(vendor);
+
+static int product_show(struct seq_file *seqf, void *unused)
+{
+	struct corsairpsu_data *priv = seqf->private;
+
+	seq_printf(seqf, "%s\n", priv->product);
+
+	return 0;
+}
+DEFINE_SHOW_ATTRIBUTE(product);
+
+static void corsairpsu_debugfs_init(struct corsairpsu_data *priv)
+{
+	char name[32];
+
+	scnprintf(name, sizeof(name), "%s-%s", DRIVER_NAME, dev_name(&priv->hdev->dev));
+
+	priv->debugfs = debugfs_create_dir(name, NULL);
+	debugfs_create_file("uptime", 0444, priv->debugfs, priv, &uptime_fops);
+	debugfs_create_file("uptime_total", 0444, priv->debugfs, priv, &uptime_total_fops);
+	debugfs_create_file("vendor", 0444, priv->debugfs, priv, &vendor_fops);
+	debugfs_create_file("product", 0444, priv->debugfs, priv, &product_fops);
+}
+
+#else
+
+static void corsairpsu_debugfs_init(struct corsairpsu_data *priv)
+{
+}
+
+#endif
+
+static int corsairpsu_probe(struct hid_device *hdev, const struct hid_device_id *id)
+{
+	struct corsairpsu_data *priv;
+	int ret;
+
+	priv = devm_kzalloc(&hdev->dev, sizeof(struct corsairpsu_data), GFP_KERNEL);
+	if (!priv)
+		return -ENOMEM;
+
+	priv->cmd_buffer = devm_kmalloc(&hdev->dev, CMD_BUFFER_SIZE, GFP_KERNEL);
+	if (!priv->cmd_buffer)
+		return -ENOMEM;
+
+	ret = hid_parse(hdev);
+	if (ret)
+		return ret;
+
+	ret = hid_hw_start(hdev, HID_CONNECT_HIDRAW);
+	if (ret)
+		return ret;
+
+	ret = hid_hw_open(hdev);
+	if (ret)
+		goto fail_and_stop;
+
+	priv->hdev = hdev;
+	hid_set_drvdata(hdev, priv);
+	mutex_init(&priv->lock);
+	init_completion(&priv->wait_completion);
+
+	hid_device_io_start(hdev);
+
+	ret = corsairpsu_init(priv);
+	if (ret < 0) {
+		dev_err(&hdev->dev, "unable to initialize device (%d)\n", ret);
+		goto fail_and_stop;
+	}
+
+	ret = corsairpsu_fwinfo(priv);
+	if (ret < 0) {
+		dev_err(&hdev->dev, "unable to query firmware (%d)\n", ret);
+		goto fail_and_stop;
+	}
+
+	priv->hwmon_dev = hwmon_device_register_with_info(&hdev->dev, "corsairpsu", priv,
+							  &corsairpsu_chip_info, 0);
+
+	if (IS_ERR(priv->hwmon_dev)) {
+		ret = PTR_ERR(priv->hwmon_dev);
+		goto fail_and_close;
+	}
+
+	corsairpsu_debugfs_init(priv);
+
+	return 0;
+
+fail_and_close:
+	hid_hw_close(hdev);
+fail_and_stop:
+	hid_hw_stop(hdev);
+	return ret;
+}
+
+static void corsairpsu_remove(struct hid_device *hdev)
+{
+	struct corsairpsu_data *priv = hid_get_drvdata(hdev);
+
+	debugfs_remove_recursive(priv->debugfs);
+	hwmon_device_unregister(priv->hwmon_dev);
+	hid_hw_close(hdev);
+	hid_hw_stop(hdev);
+}
+
+static int corsairpsu_raw_event(struct hid_device *hdev, struct hid_report *report, u8 *data,
+				int size)
+{
+	struct corsairpsu_data *priv = hid_get_drvdata(hdev);
+
+	if (completion_done(&priv->wait_completion))
+		return 0;
+
+	memcpy(priv->cmd_buffer, data, min(CMD_BUFFER_SIZE, size));
+	complete(&priv->wait_completion);
+
+	return 0;
+}
+
+static const struct hid_device_id corsairpsu_idtable[] = {
+	{ HID_USB_DEVICE(0x1b1c, 0x1c03) }, /* Corsair HX550i */
+	{ HID_USB_DEVICE(0x1b1c, 0x1c04) }, /* Corsair HX650i */
+	{ HID_USB_DEVICE(0x1b1c, 0x1c05) }, /* Corsair HX750i */
+	{ HID_USB_DEVICE(0x1b1c, 0x1c06) }, /* Corsair HX850i */
+	{ HID_USB_DEVICE(0x1b1c, 0x1c07) }, /* Corsair HX1000i */
+	{ HID_USB_DEVICE(0x1b1c, 0x1c08) }, /* Corsair HX1200i */
+	{ HID_USB_DEVICE(0x1b1c, 0x1c09) }, /* Corsair RM550i */
+	{ HID_USB_DEVICE(0x1b1c, 0x1c0a) }, /* Corsair RM650i */
+	{ HID_USB_DEVICE(0x1b1c, 0x1c0b) }, /* Corsair RM750i */
+	{ HID_USB_DEVICE(0x1b1c, 0x1c0c) }, /* Corsair RM850i */
+	{ HID_USB_DEVICE(0x1b1c, 0x1c0d) }, /* Corsair RM1000i */
+	{ },
+};
+MODULE_DEVICE_TABLE(hid, corsairpsu_idtable);
+
+static struct hid_driver corsairpsu_driver = {
+	.name		= DRIVER_NAME,
+	.id_table	= corsairpsu_idtable,
+	.probe		= corsairpsu_probe,
+	.remove		= corsairpsu_remove,
+	.raw_event	= corsairpsu_raw_event,
+};
+module_hid_driver(corsairpsu_driver);
+
+MODULE_LICENSE("GPL");
+MODULE_AUTHOR("Wilken Gottwalt <wilken.gottwalt@posteo.net>");
+MODULE_DESCRIPTION("Linux driver for Corsair power supplies with HID sensors interface");