net: stmmac:sti: Add STi SOC glue driver.
STi series SOCs have a glue layer on top of the synopsis gmac IP, this glue layer needs to be configured before the gmac driver starts using the IP. This patch adds a support to this glue layer which is configured via stmmac setup, init, exit callbacks. Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com> Signed-off-by: David S. Miller <davem@davemloft.net>
This commit is contained in:
Srinivas Kandagatla
David S. Miller
Родитель
c7966b525f
Коммит
d15891ca1f
|
|
@ -0,0 +1,58 @@
|
|||
STMicroelectronics SoC DWMAC glue layer controller
|
||||
|
||||
The device node has following properties.
|
||||
|
||||
Required properties:
|
||||
- compatible : Can be "st,stih415-dwmac", "st,stih416-dwmac" or
|
||||
"st,stid127-dwmac".
|
||||
- reg : Offset of the glue configuration register map in system
|
||||
configuration regmap pointed by st,syscon property and size.
|
||||
|
||||
- reg-names : Should be "sti-ethconf".
|
||||
|
||||
- st,syscon : Should be phandle to system configuration node which
|
||||
encompases this glue registers.
|
||||
|
||||
- st,tx-retime-src: On STi Parts for Giga bit speeds, 125Mhz clocks can be
|
||||
wired up in from different sources. One via TXCLK pin and other via CLK_125
|
||||
pin. This wiring is totally board dependent. However the retiming glue
|
||||
logic should be configured accordingly. Possible values for this property
|
||||
|
||||
"txclk" - if 125Mhz clock is wired up via txclk line.
|
||||
"clk_125" - if 125Mhz clock is wired up via clk_125 line.
|
||||
|
||||
This property is only valid for Giga bit setup( GMII, RGMII), and it is
|
||||
un-used for non-giga bit (MII and RMII) setups. Also note that internal
|
||||
clockgen can not generate stable 125Mhz clock.
|
||||
|
||||
- st,ext-phyclk: This boolean property indicates who is generating the clock
|
||||
for tx and rx. This property is only valid for RMII case where the clock can
|
||||
be generated from the MAC or PHY.
|
||||
|
||||
- clock-names: should be "sti-ethclk".
|
||||
- clocks: Should point to ethernet clockgen which can generate phyclk.
|
||||
|
||||
|
||||
Example:
|
||||
|
||||
ethernet0: dwmac@fe810000 {
|
||||
device_type = "network";
|
||||
compatible = "st,stih416-dwmac", "snps,dwmac", "snps,dwmac-3.710";
|
||||
reg = <0xfe810000 0x8000>, <0x8bc 0x4>;
|
||||
reg-names = "stmmaceth", "sti-ethconf";
|
||||
interrupts = <0 133 0>, <0 134 0>, <0 135 0>;
|
||||
interrupt-names = "macirq", "eth_wake_irq", "eth_lpi";
|
||||
phy-mode = "mii";
|
||||
|
||||
st,syscon = <&syscfg_rear>;
|
||||
|
||||
snps,pbl = <32>;
|
||||
snps,mixed-burst;
|
||||
|
||||
resets = <&softreset STIH416_ETH0_SOFTRESET>;
|
||||
reset-names = "stmmaceth";
|
||||
pinctrl-0 = <&pinctrl_mii0>;
|
||||
pinctrl-names = "default";
|
||||
clocks = <&CLK_S_GMAC0_PHY>;
|
||||
clock-names = "stmmaceth";
|
||||
};
|
||||
|
|
@ -37,6 +37,17 @@ config DWMAC_SUNXI
|
|||
stmmac device driver. This driver is used for A20/A31
|
||||
GMAC ethernet controller.
|
||||
|
||||
config DWMAC_STI
|
||||
bool "STi GMAC support"
|
||||
depends on STMMAC_PLATFORM && ARCH_STI
|
||||
default y
|
||||
---help---
|
||||
Support for ethernet controller on STi SOCs.
|
||||
|
||||
This selects STi SoC glue layer support for the stmmac
|
||||
device driver. This driver is used on for the STi series
|
||||
SOCs GMAC ethernet controller.
|
||||
|
||||
config STMMAC_PCI
|
||||
bool "STMMAC PCI bus support"
|
||||
depends on STMMAC_ETH && PCI
|
||||
|
|
|
|||
|
|
@ -2,6 +2,7 @@ obj-$(CONFIG_STMMAC_ETH) += stmmac.o
|
|||
stmmac-$(CONFIG_STMMAC_PLATFORM) += stmmac_platform.o
|
||||
stmmac-$(CONFIG_STMMAC_PCI) += stmmac_pci.o
|
||||
stmmac-$(CONFIG_DWMAC_SUNXI) += dwmac-sunxi.o
|
||||
stmmac-$(CONFIG_DWMAC_STI) += dwmac-sti.o
|
||||
stmmac-objs:= stmmac_main.o stmmac_ethtool.o stmmac_mdio.o ring_mode.o \
|
||||
chain_mode.o dwmac_lib.o dwmac1000_core.o dwmac1000_dma.o \
|
||||
dwmac100_core.o dwmac100_dma.o enh_desc.o norm_desc.o \
|
||||
|
|
|
|||
|
|
@ -0,0 +1,330 @@
|
|||
/**
|
||||
* dwmac-sti.c - STMicroelectronics DWMAC Specific Glue layer
|
||||
*
|
||||
* Copyright (C) 2003-2014 STMicroelectronics (R&D) Limited
|
||||
* Author: Srinivas Kandagatla <srinivas.kandagatla@st.com>
|
||||
*
|
||||
*
|
||||
* This program is free software; you can redistribute it and/or modify
|
||||
* it under the terms of the GNU General Public License as published by
|
||||
* the Free Software Foundation; either version 2 of the License, or
|
||||
* (at your option) any later version.
|
||||
*/
|
||||
|
||||
#include <linux/kernel.h>
|
||||
#include <linux/slab.h>
|
||||
#include <linux/platform_device.h>
|
||||
#include <linux/stmmac.h>
|
||||
#include <linux/phy.h>
|
||||
#include <linux/mfd/syscon.h>
|
||||
#include <linux/regmap.h>
|
||||
#include <linux/clk.h>
|
||||
#include <linux/of.h>
|
||||
#include <linux/of_net.h>
|
||||
|
||||
/**
|
||||
* STi GMAC glue logic.
|
||||
* --------------------
|
||||
*
|
||||
* _
|
||||
* | \
|
||||
* --------|0 \ ETH_SEL_INTERNAL_NOTEXT_PHYCLK
|
||||
* phyclk | |___________________________________________
|
||||
* | | | (phyclk-in)
|
||||
* --------|1 / |
|
||||
* int-clk |_ / |
|
||||
* | _
|
||||
* | | \
|
||||
* |_______|1 \ ETH_SEL_TX_RETIME_CLK
|
||||
* | |___________________________
|
||||
* | | (tx-retime-clk)
|
||||
* _______|0 /
|
||||
* | |_ /
|
||||
* _ |
|
||||
* | \ |
|
||||
* --------|0 \ |
|
||||
* clk_125 | |__|
|
||||
* | | ETH_SEL_TXCLK_NOT_CLK125
|
||||
* --------|1 /
|
||||
* txclk |_ /
|
||||
*
|
||||
*
|
||||
* ETH_SEL_INTERNAL_NOTEXT_PHYCLK is valid only for RMII where PHY can
|
||||
* generate 50MHz clock or MAC can generate it.
|
||||
* This bit is configured by "st,ext-phyclk" property.
|
||||
*
|
||||
* ETH_SEL_TXCLK_NOT_CLK125 is only valid for gigabit modes, where the 125Mhz
|
||||
* clock either comes from clk-125 pin or txclk pin. This configuration is
|
||||
* totally driven by the board wiring. This bit is configured by
|
||||
* "st,tx-retime-src" property.
|
||||
*
|
||||
* TXCLK configuration is different for different phy interface modes
|
||||
* and changes according to link speed in modes like RGMII.
|
||||
*
|
||||
* Below table summarizes the clock requirement and clock sources for
|
||||
* supported phy interface modes with link speeds.
|
||||
* ________________________________________________
|
||||
*| PHY_MODE | 1000 Mbit Link | 100 Mbit Link |
|
||||
* ------------------------------------------------
|
||||
*| MII | n/a | 25Mhz |
|
||||
*| | | txclk |
|
||||
* ------------------------------------------------
|
||||
*| GMII | 125Mhz | 25Mhz |
|
||||
*| | clk-125/txclk | txclk |
|
||||
* ------------------------------------------------
|
||||
*| RGMII | 125Mhz | 25Mhz |
|
||||
*| | clk-125/txclk | clkgen |
|
||||
* ------------------------------------------------
|
||||
*| RMII | n/a | 25Mhz |
|
||||
*| | |clkgen/phyclk-in |
|
||||
* ------------------------------------------------
|
||||
*
|
||||
* TX lines are always retimed with a clk, which can vary depending
|
||||
* on the board configuration. Below is the table of these bits
|
||||
* in eth configuration register depending on source of retime clk.
|
||||
*
|
||||
*---------------------------------------------------------------
|
||||
* src | tx_rt_clk | int_not_ext_phyclk | txclk_n_clk125|
|
||||
*---------------------------------------------------------------
|
||||
* txclk | 0 | n/a | 1 |
|
||||
*---------------------------------------------------------------
|
||||
* ck_125| 0 | n/a | 0 |
|
||||
*---------------------------------------------------------------
|
||||
* phyclk| 1 | 0 | n/a |
|
||||
*---------------------------------------------------------------
|
||||
* clkgen| 1 | 1 | n/a |
|
||||
*---------------------------------------------------------------
|
||||
*/
|
||||
|
||||
/* Register definition */
|
||||
|
||||
/* 3 bits [8:6]
|
||||
* [6:6] ETH_SEL_TXCLK_NOT_CLK125
|
||||
* [7:7] ETH_SEL_INTERNAL_NOTEXT_PHYCLK
|
||||
* [8:8] ETH_SEL_TX_RETIME_CLK
|
||||
*
|
||||
*/
|
||||
|
||||
#define TX_RETIME_SRC_MASK GENMASK(8, 6)
|
||||
#define ETH_SEL_TX_RETIME_CLK BIT(8)
|
||||
#define ETH_SEL_INTERNAL_NOTEXT_PHYCLK BIT(7)
|
||||
#define ETH_SEL_TXCLK_NOT_CLK125 BIT(6)
|
||||
|
||||
#define ENMII_MASK GENMASK(5, 5)
|
||||
#define ENMII BIT(5)
|
||||
|
||||
/**
|
||||
* 3 bits [4:2]
|
||||
* 000-GMII/MII
|
||||
* 001-RGMII
|
||||
* 010-SGMII
|
||||
* 100-RMII
|
||||
*/
|
||||
#define MII_PHY_SEL_MASK GENMASK(4, 2)
|
||||
#define ETH_PHY_SEL_RMII BIT(4)
|
||||
#define ETH_PHY_SEL_SGMII BIT(3)
|
||||
#define ETH_PHY_SEL_RGMII BIT(2)
|
||||
#define ETH_PHY_SEL_GMII 0x0
|
||||
#define ETH_PHY_SEL_MII 0x0
|
||||
|
||||
#define IS_PHY_IF_MODE_RGMII(iface) (iface == PHY_INTERFACE_MODE_RGMII || \
|
||||
iface == PHY_INTERFACE_MODE_RGMII_ID || \
|
||||
iface == PHY_INTERFACE_MODE_RGMII_RXID || \
|
||||
iface == PHY_INTERFACE_MODE_RGMII_TXID)
|
||||
|
||||
#define IS_PHY_IF_MODE_GBIT(iface) (IS_PHY_IF_MODE_RGMII(iface) || \
|
||||
iface == PHY_INTERFACE_MODE_GMII)
|
||||
|
||||
struct sti_dwmac {
|
||||
int interface;
|
||||
bool ext_phyclk;
|
||||
bool is_tx_retime_src_clk_125;
|
||||
struct clk *clk;
|
||||
int reg;
|
||||
struct device *dev;
|
||||
struct regmap *regmap;
|
||||
};
|
||||
|
||||
static u32 phy_intf_sels[] = {
|
||||
[PHY_INTERFACE_MODE_MII] = ETH_PHY_SEL_MII,
|
||||
[PHY_INTERFACE_MODE_GMII] = ETH_PHY_SEL_GMII,
|
||||
[PHY_INTERFACE_MODE_RGMII] = ETH_PHY_SEL_RGMII,
|
||||
[PHY_INTERFACE_MODE_RGMII_ID] = ETH_PHY_SEL_RGMII,
|
||||
[PHY_INTERFACE_MODE_SGMII] = ETH_PHY_SEL_SGMII,
|
||||
[PHY_INTERFACE_MODE_RMII] = ETH_PHY_SEL_RMII,
|
||||
};
|
||||
|
||||
enum {
|
||||
TX_RETIME_SRC_NA = 0,
|
||||
TX_RETIME_SRC_TXCLK = 1,
|
||||
TX_RETIME_SRC_CLK_125,
|
||||
TX_RETIME_SRC_PHYCLK,
|
||||
TX_RETIME_SRC_CLKGEN,
|
||||
};
|
||||
|
||||
static const char *const tx_retime_srcs[] = {
|
||||
[TX_RETIME_SRC_NA] = "",
|
||||
[TX_RETIME_SRC_TXCLK] = "txclk",
|
||||
[TX_RETIME_SRC_CLK_125] = "clk_125",
|
||||
[TX_RETIME_SRC_PHYCLK] = "phyclk",
|
||||
[TX_RETIME_SRC_CLKGEN] = "clkgen",
|
||||
};
|
||||
|
||||
static u32 tx_retime_val[] = {
|
||||
[TX_RETIME_SRC_TXCLK] = ETH_SEL_TXCLK_NOT_CLK125,
|
||||
[TX_RETIME_SRC_CLK_125] = 0x0,
|
||||
[TX_RETIME_SRC_PHYCLK] = ETH_SEL_TX_RETIME_CLK,
|
||||
[TX_RETIME_SRC_CLKGEN] = ETH_SEL_TX_RETIME_CLK |
|
||||
ETH_SEL_INTERNAL_NOTEXT_PHYCLK,
|
||||
};
|
||||
|
||||
static void setup_retime_src(struct sti_dwmac *dwmac, u32 spd)
|
||||
{
|
||||
u32 src = 0, freq = 0;
|
||||
|
||||
if (spd == SPEED_100) {
|
||||
if (dwmac->interface == PHY_INTERFACE_MODE_MII ||
|
||||
dwmac->interface == PHY_INTERFACE_MODE_GMII) {
|
||||
src = TX_RETIME_SRC_TXCLK;
|
||||
} else if (dwmac->interface == PHY_INTERFACE_MODE_RMII) {
|
||||
if (dwmac->ext_phyclk) {
|
||||
src = TX_RETIME_SRC_PHYCLK;
|
||||
} else {
|
||||
src = TX_RETIME_SRC_CLKGEN;
|
||||
freq = 50000000;
|
||||
}
|
||||
|
||||
} else if (IS_PHY_IF_MODE_RGMII(dwmac->interface)) {
|
||||
src = TX_RETIME_SRC_CLKGEN;
|
||||
freq = 25000000;
|
||||
}
|
||||
|
||||
if (src == TX_RETIME_SRC_CLKGEN && dwmac->clk)
|
||||
clk_set_rate(dwmac->clk, freq);
|
||||
|
||||
} else if (spd == SPEED_1000) {
|
||||
if (dwmac->is_tx_retime_src_clk_125)
|
||||
src = TX_RETIME_SRC_CLK_125;
|
||||
else
|
||||
src = TX_RETIME_SRC_TXCLK;
|
||||
}
|
||||
|
||||
regmap_update_bits(dwmac->regmap, dwmac->reg,
|
||||
TX_RETIME_SRC_MASK, tx_retime_val[src]);
|
||||
}
|
||||
|
||||
static void sti_dwmac_exit(struct platform_device *pdev, void *priv)
|
||||
{
|
||||
struct sti_dwmac *dwmac = priv;
|
||||
|
||||
if (dwmac->clk)
|
||||
clk_disable_unprepare(dwmac->clk);
|
||||
}
|
||||
|
||||
static void sti_fix_mac_speed(void *priv, unsigned int spd)
|
||||
{
|
||||
struct sti_dwmac *dwmac = priv;
|
||||
|
||||
setup_retime_src(dwmac, spd);
|
||||
|
||||
return;
|
||||
}
|
||||
|
||||
static int sti_dwmac_parse_data(struct sti_dwmac *dwmac,
|
||||
struct platform_device *pdev)
|
||||
{
|
||||
struct resource *res;
|
||||
struct device *dev = &pdev->dev;
|
||||
struct device_node *np = dev->of_node;
|
||||
struct regmap *regmap;
|
||||
int err;
|
||||
|
||||
if (!np)
|
||||
return -EINVAL;
|
||||
|
||||
res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "sti-ethconf");
|
||||
if (!res)
|
||||
return -ENODATA;
|
||||
|
||||
regmap = syscon_regmap_lookup_by_phandle(np, "st,syscon");
|
||||
if (IS_ERR(regmap))
|
||||
return PTR_ERR(regmap);
|
||||
|
||||
dwmac->dev = dev;
|
||||
dwmac->interface = of_get_phy_mode(np);
|
||||
dwmac->regmap = regmap;
|
||||
dwmac->reg = res->start;
|
||||
dwmac->ext_phyclk = of_property_read_bool(np, "st,ext-phyclk");
|
||||
dwmac->is_tx_retime_src_clk_125 = false;
|
||||
|
||||
if (IS_PHY_IF_MODE_GBIT(dwmac->interface)) {
|
||||
const char *rs;
|
||||
|
||||
err = of_property_read_string(np, "st,tx-retime-src", &rs);
|
||||
if (err < 0) {
|
||||
dev_err(dev, "st,tx-retime-src not specified\n");
|
||||
return err;
|
||||
}
|
||||
|
||||
if (!strcasecmp(rs, "clk_125"))
|
||||
dwmac->is_tx_retime_src_clk_125 = true;
|
||||
}
|
||||
|
||||
dwmac->clk = devm_clk_get(dev, "sti-ethclk");
|
||||
|
||||
if (IS_ERR(dwmac->clk))
|
||||
dwmac->clk = NULL;
|
||||
|
||||
return 0;
|
||||
}
|
||||
|
||||
static int sti_dwmac_init(struct platform_device *pdev, void *priv)
|
||||
{
|
||||
struct sti_dwmac *dwmac = priv;
|
||||
struct regmap *regmap = dwmac->regmap;
|
||||
int iface = dwmac->interface;
|
||||
u32 reg = dwmac->reg;
|
||||
u32 val, spd;
|
||||
|
||||
if (dwmac->clk)
|
||||
clk_prepare_enable(dwmac->clk);
|
||||
|
||||
regmap_update_bits(regmap, reg, MII_PHY_SEL_MASK, phy_intf_sels[iface]);
|
||||
|
||||
val = (iface == PHY_INTERFACE_MODE_REVMII) ? 0 : ENMII;
|
||||
regmap_update_bits(regmap, reg, ENMII_MASK, val);
|
||||
|
||||
if (IS_PHY_IF_MODE_GBIT(iface))
|
||||
spd = SPEED_1000;
|
||||
else
|
||||
spd = SPEED_100;
|
||||
|
||||
setup_retime_src(dwmac, spd);
|
||||
|
||||
return 0;
|
||||
}
|
||||
|
||||
static void *sti_dwmac_setup(struct platform_device *pdev)
|
||||
{
|
||||
struct sti_dwmac *dwmac;
|
||||
int ret;
|
||||
|
||||
dwmac = devm_kzalloc(&pdev->dev, sizeof(*dwmac), GFP_KERNEL);
|
||||
if (!dwmac)
|
||||
return ERR_PTR(-ENOMEM);
|
||||
|
||||
ret = sti_dwmac_parse_data(dwmac, pdev);
|
||||
if (ret) {
|
||||
dev_err(&pdev->dev, "Unable to parse OF data\n");
|
||||
return ERR_PTR(ret);
|
||||
}
|
||||
|
||||
return dwmac;
|
||||
}
|
||||
|
||||
const struct stmmac_of_data sti_gmac_data = {
|
||||
.fix_mac_speed = sti_fix_mac_speed,
|
||||
.setup = sti_dwmac_setup,
|
||||
.init = sti_dwmac_init,
|
||||
.exit = sti_dwmac_exit,
|
||||
};
|
||||
|
|
@ -133,6 +133,9 @@ bool stmmac_eee_init(struct stmmac_priv *priv);
|
|||
#ifdef CONFIG_DWMAC_SUNXI
|
||||
extern const struct stmmac_of_data sun7i_gmac_data;
|
||||
#endif
|
||||
#ifdef CONFIG_DWMAC_STI
|
||||
extern const struct stmmac_of_data sti_gmac_data;
|
||||
#endif
|
||||
extern struct platform_driver stmmac_pltfr_driver;
|
||||
static inline int stmmac_register_platform(void)
|
||||
{
|
||||
|
|
|
|||
|
|
@ -32,6 +32,11 @@
|
|||
static const struct of_device_id stmmac_dt_ids[] = {
|
||||
#ifdef CONFIG_DWMAC_SUNXI
|
||||
{ .compatible = "allwinner,sun7i-a20-gmac", .data = &sun7i_gmac_data},
|
||||
#endif
|
||||
#ifdef CONFIG_DWMAC_STI
|
||||
{ .compatible = "st,stih415-dwmac", .data = &sti_gmac_data},
|
||||
{ .compatible = "st,stih416-dwmac", .data = &sti_gmac_data},
|
||||
{ .compatible = "st,stih127-dwmac", .data = &sti_gmac_data},
|
||||
#endif
|
||||
/* SoC specific glue layers should come before generic bindings */
|
||||
{ .compatible = "st,spear600-gmac"},
|
||||
|
|
|
|||
Загрузка…
Ссылка в новой задаче