clk: clk-si544: Implement small frequency change support

The Si544 supports changing frequencies "on the fly" when the change is
less than 950 ppm from the current center frequency. The driver now
uses the small adjustment routine for implementing this.

Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
This commit is contained in:
Mike Looijmans 2019-05-07 15:51:10 +02:00 коммит произвёл Stephen Boyd
Родитель a188339ca5
Коммит dc59c13375
1 изменённых файлов: 93 добавлений и 11 удалений

Просмотреть файл

@ -7,6 +7,7 @@
#include <linux/clk-provider.h>
#include <linux/delay.h>
#include <linux/math64.h>
#include <linux/module.h>
#include <linux/i2c.h>
#include <linux/regmap.h>
@ -50,6 +51,11 @@
/* Lowest frequency synthesizeable using only the HS divider */
#define MIN_HSDIV_FREQ (FVCO_MIN / HS_DIV_MAX)
/* Range and interpretation of the adjustment value */
#define DELTA_M_MAX 8161512
#define DELTA_M_FRAC_NUM 19
#define DELTA_M_FRAC_DEN 20000
enum si544_speed_grade {
si544a,
si544b,
@ -71,12 +77,14 @@ struct clk_si544 {
* @hs_div: 1st divider, 5..2046, must be even when >33
* @ls_div_bits: 2nd divider, as 2^x, range 0..5
* If ls_div_bits is non-zero, hs_div must be even
* @delta_m: Frequency shift for small -950..+950 ppm changes, 24 bit
*/
struct clk_si544_muldiv {
u32 fb_div_frac;
u16 fb_div_int;
u16 hs_div;
u8 ls_div_bits;
s32 delta_m;
};
/* Enables or disables the output driver */
@ -134,9 +142,30 @@ static int si544_get_muldiv(struct clk_si544 *data,
settings->fb_div_int = reg[4] | (reg[5] & 0x07) << 8;
settings->fb_div_frac = reg[0] | reg[1] << 8 | reg[2] << 16 |
reg[3] << 24;
err = regmap_bulk_read(data->regmap, SI544_REG_ADPLL_DELTA_M0, reg, 3);
if (err)
return err;
/* Interpret as 24-bit signed number */
settings->delta_m = reg[0] << 8 | reg[1] << 16 | reg[2] << 24;
settings->delta_m >>= 8;
return 0;
}
static int si544_set_delta_m(struct clk_si544 *data, s32 delta_m)
{
u8 reg[3];
reg[0] = delta_m;
reg[1] = delta_m >> 8;
reg[2] = delta_m >> 16;
return regmap_bulk_write(data->regmap, SI544_REG_ADPLL_DELTA_M0,
reg, 3);
}
static int si544_set_muldiv(struct clk_si544 *data,
struct clk_si544_muldiv *settings)
{
@ -238,11 +267,15 @@ static int si544_calc_muldiv(struct clk_si544_muldiv *settings,
do_div(vco, FXO);
settings->fb_div_frac = vco;
/* Reset the frequency adjustment */
settings->delta_m = 0;
return 0;
}
/* Calculate resulting frequency given the register settings */
static unsigned long si544_calc_rate(struct clk_si544_muldiv *settings)
static unsigned long si544_calc_center_rate(
const struct clk_si544_muldiv *settings)
{
u32 d = settings->hs_div * BIT(settings->ls_div_bits);
u64 vco;
@ -261,6 +294,25 @@ static unsigned long si544_calc_rate(struct clk_si544_muldiv *settings)
return vco;
}
static unsigned long si544_calc_rate(const struct clk_si544_muldiv *settings)
{
unsigned long rate = si544_calc_center_rate(settings);
s64 delta = (s64)rate * (DELTA_M_FRAC_NUM * settings->delta_m);
/*
* The clock adjustment is much smaller than 1 Hz, round to the
* nearest multiple. Apparently div64_s64 rounds towards zero, hence
* check the sign and adjust into the proper direction.
*/
if (settings->delta_m < 0)
delta -= ((s64)DELTA_M_MAX * DELTA_M_FRAC_DEN) / 2;
else
delta += ((s64)DELTA_M_MAX * DELTA_M_FRAC_DEN) / 2;
delta = div64_s64(delta, ((s64)DELTA_M_MAX * DELTA_M_FRAC_DEN));
return rate + delta;
}
static unsigned long si544_recalc_rate(struct clk_hw *hw,
unsigned long parent_rate)
{
@ -279,33 +331,60 @@ static long si544_round_rate(struct clk_hw *hw, unsigned long rate,
unsigned long *parent_rate)
{
struct clk_si544 *data = to_clk_si544(hw);
struct clk_si544_muldiv settings;
int err;
if (!is_valid_frequency(data, rate))
return -EINVAL;
err = si544_calc_muldiv(&settings, rate);
if (err)
return err;
return si544_calc_rate(&settings);
/* The accuracy is less than 1 Hz, so any rate is possible */
return rate;
}
/* Calculates the maximum "small" change, 950 * rate / 1000000 */
static unsigned long si544_max_delta(unsigned long rate)
{
u64 num = rate;
num *= DELTA_M_FRAC_NUM;
do_div(num, DELTA_M_FRAC_DEN);
return num;
}
static s32 si544_calc_delta(s32 delta, s32 max_delta)
{
s64 n = (s64)delta * DELTA_M_MAX;
return div_s64(n, max_delta);
}
/*
* Update output frequency for "big" frequency changes
*/
static int si544_set_rate(struct clk_hw *hw, unsigned long rate,
unsigned long parent_rate)
{
struct clk_si544 *data = to_clk_si544(hw);
struct clk_si544_muldiv settings;
unsigned long center;
long max_delta;
long delta;
unsigned int old_oe_state;
int err;
if (!is_valid_frequency(data, rate))
return -EINVAL;
/* Try using the frequency adjustment feature for a <= 950ppm change */
err = si544_get_muldiv(data, &settings);
if (err)
return err;
center = si544_calc_center_rate(&settings);
max_delta = si544_max_delta(center);
delta = rate - center;
if (abs(delta) <= max_delta)
return si544_set_delta_m(data,
si544_calc_delta(delta, max_delta));
/* Too big for the delta adjustment, need to reprogram */
err = si544_calc_muldiv(&settings, rate);
if (err)
return err;
@ -321,6 +400,9 @@ static int si544_set_rate(struct clk_hw *hw, unsigned long rate,
if (err < 0)
return err;
err = si544_set_delta_m(data, settings.delta_m);
if (err < 0)
return err;
err = si544_set_muldiv(data, &settings);
if (err < 0)