ipv4/icmp: l3mdev: Perform icmp error route lookup on source device routing table (v2)
As per RFC792, ICMP errors should be sent to the source host. However, in configurations with Virtual Routing and Forwarding tables, looking up which routing table to use is currently done by using the destination net_device. commit9d1a6c4ea4
("net: icmp_route_lookup should use rt dev to determine L3 domain") changes the interface passed to l3mdev_master_ifindex() and inet_addr_type_dev_table() from skb_in->dev to skb_dst(skb_in)->dev. This effectively uses the destination device rather than the source device for choosing which routing table should be used to lookup where to send the ICMP error. Therefore, if the source and destination interfaces are within separate VRFs, or one in the global routing table and the other in a VRF, looking up the source host in the destination interface's routing table will fail if the destination interface's routing table contains no route to the source host. One observable effect of this issue is that traceroute does not work in the following cases: - Route leaking between global routing table and VRF - Route leaking between VRFs Preferably use the source device routing table when sending ICMP error messages. If no source device is set, fall-back on the destination device routing table. Else, use the main routing table (index 0). [ It has been pointed out that a similar issue may exist with ICMP errors triggered when forwarding between network namespaces. It would be worthwhile to investigate, but is outside of the scope of this investigation. ] [ It has also been pointed out that a similar issue exists with unreachable / fragmentation needed messages, which can be triggered by changing the MTU of eth1 in r1 to 1400 and running: ip netns exec h1 ping -s 1450 -Mdo -c1 172.16.2.2 Some investigation points to raw_icmp_error() and raw_err() as being involved in this last scenario. The focus of this patch is TTL expired ICMP messages, which go through icmp_route_lookup. Investigation of failure modes related to raw_icmp_error() is beyond this investigation's scope. ] Fixes:9d1a6c4ea4
("net: icmp_route_lookup should use rt dev to determine L3 domain") Link: https://tools.ietf.org/html/rfc792 Signed-off-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com> Reviewed-by: David Ahern <dsahern@gmail.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This commit is contained in:
Родитель
1e40d75ef9
Коммит
e1e84eb58e
|
@ -457,6 +457,23 @@ out_bh_enable:
|
|||
local_bh_enable();
|
||||
}
|
||||
|
||||
/*
|
||||
* The device used for looking up which routing table to use for sending an ICMP
|
||||
* error is preferably the source whenever it is set, which should ensure the
|
||||
* icmp error can be sent to the source host, else lookup using the routing
|
||||
* table of the destination device, else use the main routing table (index 0).
|
||||
*/
|
||||
static struct net_device *icmp_get_route_lookup_dev(struct sk_buff *skb)
|
||||
{
|
||||
struct net_device *route_lookup_dev = NULL;
|
||||
|
||||
if (skb->dev)
|
||||
route_lookup_dev = skb->dev;
|
||||
else if (skb_dst(skb))
|
||||
route_lookup_dev = skb_dst(skb)->dev;
|
||||
return route_lookup_dev;
|
||||
}
|
||||
|
||||
static struct rtable *icmp_route_lookup(struct net *net,
|
||||
struct flowi4 *fl4,
|
||||
struct sk_buff *skb_in,
|
||||
|
@ -465,6 +482,7 @@ static struct rtable *icmp_route_lookup(struct net *net,
|
|||
int type, int code,
|
||||
struct icmp_bxm *param)
|
||||
{
|
||||
struct net_device *route_lookup_dev;
|
||||
struct rtable *rt, *rt2;
|
||||
struct flowi4 fl4_dec;
|
||||
int err;
|
||||
|
@ -479,7 +497,8 @@ static struct rtable *icmp_route_lookup(struct net *net,
|
|||
fl4->flowi4_proto = IPPROTO_ICMP;
|
||||
fl4->fl4_icmp_type = type;
|
||||
fl4->fl4_icmp_code = code;
|
||||
fl4->flowi4_oif = l3mdev_master_ifindex(skb_dst(skb_in)->dev);
|
||||
route_lookup_dev = icmp_get_route_lookup_dev(skb_in);
|
||||
fl4->flowi4_oif = l3mdev_master_ifindex(route_lookup_dev);
|
||||
|
||||
security_skb_classify_flow(skb_in, flowi4_to_flowi(fl4));
|
||||
rt = ip_route_output_key_hash(net, fl4, skb_in);
|
||||
|
@ -503,7 +522,7 @@ static struct rtable *icmp_route_lookup(struct net *net,
|
|||
if (err)
|
||||
goto relookup_failed;
|
||||
|
||||
if (inet_addr_type_dev_table(net, skb_dst(skb_in)->dev,
|
||||
if (inet_addr_type_dev_table(net, route_lookup_dev,
|
||||
fl4_dec.saddr) == RTN_LOCAL) {
|
||||
rt2 = __ip_route_output_key(net, &fl4_dec);
|
||||
if (IS_ERR(rt2))
|
||||
|
|
Загрузка…
Ссылка в новой задаче