i.MX fixes for 5.11, round 2:

- Fix pcf2127 reset for imx7d-flex-concentrator board.
 - Fix i.MX6 suspend with Thumb-2 kernel.
 - Fix ethernet-phy address issue on imx6qdl-sr-som board.
 - Fix GPIO3 `gpio-ranges` on i.MX8MP.
 - Select SOC_BUS for IMX_SCU driver to fix build issue.
 -----BEGIN PGP SIGNATURE-----
 
 iQFIBAABCgAyFiEEFmJXigPl4LoGSz08UFdYWoewfM4FAmAGo5MUHHNoYXduZ3Vv
 QGtlcm5lbC5vcmcACgkQUFdYWoewfM7Djgf/aNtJzzfv0Rl18nUFcXwpC4IZ6zKK
 OENtqHqsCTLKIP4KfAyk20XhkqoWH3+fkUdgdSe7IpqM7CvYBGJNSdwe5JbpfJKp
 4n6DYEQERnNQAq9pNiZFKc4+0NDtD46wurEh7CLmzZrReKCLiLnElbNWa0wSdpcE
 pOgaPDsAGd5sYG6iSxr38Wdx18F4DllI3oOABuZbXhVjUqe8yTUt7OUrVa/9fBQS
 VC9hGn0HlPVPfPwUMn/jbYJmew6CWOFnLRB7zlBoPG345b9ggScyUKCARRFSj0a8
 c7/NwnPM/tbHF8Moiay1lZTfeLfQLFvfEW0H5+RGddXZzdI8OnVkTdGyfg==
 =IxBF
 -----END PGP SIGNATURE-----

Merge tag 'imx-fixes-5.11-2' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into arm/fixes

i.MX fixes for 5.11, round 2:

- Fix pcf2127 reset for imx7d-flex-concentrator board.
- Fix i.MX6 suspend with Thumb-2 kernel.
- Fix ethernet-phy address issue on imx6qdl-sr-som board.
- Fix GPIO3 `gpio-ranges` on i.MX8MP.
- Select SOC_BUS for IMX_SCU driver to fix build issue.

* tag 'imx-fixes-5.11-2' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
  firmware: imx: select SOC_BUS to fix firmware build
  arm64: dts: imx8mp: Correct the gpio ranges of gpio3
  ARM: dts: imx6qdl-sr-som: fix some cubox-i platforms
  ARM: imx: build suspend-imx6.S with arm instruction set
  ARM: dts: imx7d-flex-concentrator: fix pcf2127 reset

Link: https://lore.kernel.org/r/20210119091949.GD4356@dragon
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

arch/arm/boot/dts/imx6qdl-sr-som.dtsi

@@ -53,7 +53,6 @@
 &fec {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_microsom_enet_ar8035>;
-	phy-handle = <&phy>;
 	phy-mode = "rgmii-id";
 	phy-reset-duration = <2>;
 	phy-reset-gpios = <&gpio4 15 GPIO_ACTIVE_LOW>;
@@ -63,10 +62,19 @@
 		#address-cells = <1>;
 		#size-cells = <0>;
 
-		phy: ethernet-phy@0 {
+		/*
+		 * The PHY can appear at either address 0 or 4 due to the
+		 * configuration (LED) pin not being pulled sufficiently.
+		 */
+		ethernet-phy@0 {
 			reg = <0>;
 			qca,clk-out-frequency = <125000000>;
 		};
+
+		ethernet-phy@4 {
+			reg = <4>;
+			qca,clk-out-frequency = <125000000>;
+		};
 	};
 };
 

arch/arm/boot/dts/imx7d-flex-concentrator.dts

@@ -115,6 +115,7 @@
 		compatible = "nxp,pcf2127";
 		reg = <0>;
 		spi-max-frequency = <2000000>;
+		reset-source;
 	};
 };
 

arch/arm/mach-imx/suspend-imx6.S

@@ -67,6 +67,7 @@
 #define MX6Q_CCM_CCR	0x0
 
 	.align 3
+	.arm
 
 	.macro  sync_l2_cache
 

arch/arm64/boot/dts/freescale/imx8mp.dtsi

@@ -266,7 +266,7 @@
 				#gpio-cells = <2>;
 				interrupt-controller;
 				#interrupt-cells = <2>;
-				gpio-ranges = <&iomuxc 0 56 26>, <&iomuxc 0 144 4>;
+				gpio-ranges = <&iomuxc 0 56 26>, <&iomuxc 26 144 4>;
 			};
 
 			gpio4: gpio@30230000 {

drivers/firmware/imx/Kconfig

@@ -13,6 +13,7 @@ config IMX_DSP
 config IMX_SCU
 	bool "IMX SCU Protocol driver"
 	depends on IMX_MBOX
+	select SOC_BUS
 	help
 	  The System Controller Firmware (SCFW) is a low-level system function
 	  which runs on a dedicated Cortex-M core to provide power, clock, and