mtd: st_spi_fsm: Supply the N25Qxxx specific read configurations
The N25Qxxx Serial Flash devices required different sequence configurations depending on whether they're running in 24bit (3Byte) or 32bit (4Byte) mode. We provide those here. Acked-by Angus Clark <angus.clark@st.com> Signed-off-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Brian Norris <computersforpeace@gmail.com>
This commit is contained in:
Lee Jones
Brian Norris
Родитель
a37b2f5aee
Коммит
e85a619676
|
|
@ -200,6 +200,53 @@
|
||||||
|
|
||||||
#define STFSM_MAX_WAIT_SEQ_MS 1000 /* FSM execution time */
|
#define STFSM_MAX_WAIT_SEQ_MS 1000 /* FSM execution time */
|
||||||
|
|
||||||
|
/* Flash Commands */
|
||||||
|
#define FLASH_CMD_WREN 0x06
|
||||||
|
#define FLASH_CMD_WRDI 0x04
|
||||||
|
#define FLASH_CMD_RDID 0x9f
|
||||||
|
#define FLASH_CMD_RDSR 0x05
|
||||||
|
#define FLASH_CMD_RDSR2 0x35
|
||||||
|
#define FLASH_CMD_WRSR 0x01
|
||||||
|
#define FLASH_CMD_SE_4K 0x20
|
||||||
|
#define FLASH_CMD_SE_32K 0x52
|
||||||
|
#define FLASH_CMD_SE 0xd8
|
||||||
|
#define FLASH_CMD_CHIPERASE 0xc7
|
||||||
|
#define FLASH_CMD_WRVCR 0x81
|
||||||
|
#define FLASH_CMD_RDVCR 0x85
|
||||||
|
|
||||||
|
#define FLASH_CMD_READ 0x03 /* READ */
|
||||||
|
#define FLASH_CMD_READ_FAST 0x0b /* FAST READ */
|
||||||
|
#define FLASH_CMD_READ_1_1_2 0x3b /* DUAL OUTPUT READ */
|
||||||
|
#define FLASH_CMD_READ_1_2_2 0xbb /* DUAL I/O READ */
|
||||||
|
#define FLASH_CMD_READ_1_1_4 0x6b /* QUAD OUTPUT READ */
|
||||||
|
#define FLASH_CMD_READ_1_4_4 0xeb /* QUAD I/O READ */
|
||||||
|
|
||||||
|
#define FLASH_CMD_WRITE 0x02 /* PAGE PROGRAM */
|
||||||
|
#define FLASH_CMD_WRITE_1_1_2 0xa2 /* DUAL INPUT PROGRAM */
|
||||||
|
#define FLASH_CMD_WRITE_1_2_2 0xd2 /* DUAL INPUT EXT PROGRAM */
|
||||||
|
#define FLASH_CMD_WRITE_1_1_4 0x32 /* QUAD INPUT PROGRAM */
|
||||||
|
#define FLASH_CMD_WRITE_1_4_4 0x12 /* QUAD INPUT EXT PROGRAM */
|
||||||
|
|
||||||
|
#define FLASH_CMD_EN4B_ADDR 0xb7 /* Enter 4-byte address mode */
|
||||||
|
#define FLASH_CMD_EX4B_ADDR 0xe9 /* Exit 4-byte address mode */
|
||||||
|
|
||||||
|
/* READ commands with 32-bit addressing (N25Q256 and S25FLxxxS) */
|
||||||
|
#define FLASH_CMD_READ4 0x13
|
||||||
|
#define FLASH_CMD_READ4_FAST 0x0c
|
||||||
|
#define FLASH_CMD_READ4_1_1_2 0x3c
|
||||||
|
#define FLASH_CMD_READ4_1_2_2 0xbc
|
||||||
|
#define FLASH_CMD_READ4_1_1_4 0x6c
|
||||||
|
#define FLASH_CMD_READ4_1_4_4 0xec
|
||||||
|
|
||||||
|
/*
|
||||||
|
* Flags to tweak operation of default read/write/erase routines
|
||||||
|
*/
|
||||||
|
#define CFG_READ_TOGGLE_32BIT_ADDR 0x00000001
|
||||||
|
#define CFG_WRITE_TOGGLE_32BIT_ADDR 0x00000002
|
||||||
|
#define CFG_WRITE_EX_32BIT_ADDR_DELAY 0x00000004
|
||||||
|
#define CFG_ERASESEC_TOGGLE_32BIT_ADDR 0x00000008
|
||||||
|
#define CFG_S25FL_CHECK_ERROR_FLAGS 0x00000010
|
||||||
|
|
||||||
struct stfsm {
|
struct stfsm {
|
||||||
struct device *dev;
|
struct device *dev;
|
||||||
void __iomem *base;
|
void __iomem *base;
|
||||||
|
|
@ -208,6 +255,7 @@ struct stfsm {
|
||||||
struct mutex lock;
|
struct mutex lock;
|
||||||
struct flash_info *info;
|
struct flash_info *info;
|
||||||
|
|
||||||
|
uint32_t configuration;
|
||||||
uint32_t fifo_dir_delay;
|
uint32_t fifo_dir_delay;
|
||||||
bool booted_from_spi;
|
bool booted_from_spi;
|
||||||
bool reset_signal;
|
bool reset_signal;
|
||||||
|
|
@ -402,6 +450,49 @@ static struct seq_rw_config default_write_configs[] = {
|
||||||
{0x00, 0, 0, 0, 0, 0x00, 0, 0},
|
{0x00, 0, 0, 0, 0, 0x00, 0, 0},
|
||||||
};
|
};
|
||||||
|
|
||||||
|
/*
|
||||||
|
* [N25Qxxx] Configuration
|
||||||
|
*/
|
||||||
|
#define N25Q_VCR_DUMMY_CYCLES(x) (((x) & 0xf) << 4)
|
||||||
|
#define N25Q_VCR_XIP_DISABLED ((uint8_t)0x1 << 3)
|
||||||
|
#define N25Q_VCR_WRAP_CONT 0x3
|
||||||
|
|
||||||
|
/* N25Q 3-byte Address READ configurations
|
||||||
|
* - 'FAST' variants configured for 8 dummy cycles.
|
||||||
|
*
|
||||||
|
* Note, the number of dummy cycles used for 'FAST' READ operations is
|
||||||
|
* configurable and would normally be tuned according to the READ command and
|
||||||
|
* operating frequency. However, this applies universally to all 'FAST' READ
|
||||||
|
* commands, including those used by the SPIBoot controller, and remains in
|
||||||
|
* force until the device is power-cycled. Since the SPIBoot controller is
|
||||||
|
* hard-wired to use 8 dummy cycles, we must configure the device to also use 8
|
||||||
|
* cycles.
|
||||||
|
*/
|
||||||
|
static struct seq_rw_config n25q_read3_configs[] = {
|
||||||
|
{FLASH_FLAG_READ_1_4_4, FLASH_CMD_READ_1_4_4, 0, 4, 4, 0x00, 0, 8},
|
||||||
|
{FLASH_FLAG_READ_1_1_4, FLASH_CMD_READ_1_1_4, 0, 1, 4, 0x00, 0, 8},
|
||||||
|
{FLASH_FLAG_READ_1_2_2, FLASH_CMD_READ_1_2_2, 0, 2, 2, 0x00, 0, 8},
|
||||||
|
{FLASH_FLAG_READ_1_1_2, FLASH_CMD_READ_1_1_2, 0, 1, 2, 0x00, 0, 8},
|
||||||
|
{FLASH_FLAG_READ_FAST, FLASH_CMD_READ_FAST, 0, 1, 1, 0x00, 0, 8},
|
||||||
|
{FLASH_FLAG_READ_WRITE, FLASH_CMD_READ, 0, 1, 1, 0x00, 0, 0},
|
||||||
|
{0x00, 0, 0, 0, 0, 0x00, 0, 0},
|
||||||
|
};
|
||||||
|
|
||||||
|
/* N25Q 4-byte Address READ configurations
|
||||||
|
* - use special 4-byte address READ commands (reduces overheads, and
|
||||||
|
* reduces risk of hitting watchdog reset issues).
|
||||||
|
* - 'FAST' variants configured for 8 dummy cycles (see note above.)
|
||||||
|
*/
|
||||||
|
static struct seq_rw_config n25q_read4_configs[] = {
|
||||||
|
{FLASH_FLAG_READ_1_4_4, FLASH_CMD_READ4_1_4_4, 0, 4, 4, 0x00, 0, 8},
|
||||||
|
{FLASH_FLAG_READ_1_1_4, FLASH_CMD_READ4_1_1_4, 0, 1, 4, 0x00, 0, 8},
|
||||||
|
{FLASH_FLAG_READ_1_2_2, FLASH_CMD_READ4_1_2_2, 0, 2, 2, 0x00, 0, 8},
|
||||||
|
{FLASH_FLAG_READ_1_1_2, FLASH_CMD_READ4_1_1_2, 0, 1, 2, 0x00, 0, 8},
|
||||||
|
{FLASH_FLAG_READ_FAST, FLASH_CMD_READ4_FAST, 0, 1, 1, 0x00, 0, 8},
|
||||||
|
{FLASH_FLAG_READ_WRITE, FLASH_CMD_READ4, 0, 1, 1, 0x00, 0, 0},
|
||||||
|
{0x00, 0, 0, 0, 0, 0x00, 0, 0},
|
||||||
|
};
|
||||||
|
|
||||||
static struct stfsm_seq stfsm_seq_en_32bit_addr;/* Dynamically populated */
|
static struct stfsm_seq stfsm_seq_en_32bit_addr;/* Dynamically populated */
|
||||||
|
|
||||||
static struct stfsm_seq stfsm_seq_read_jedec = {
|
static struct stfsm_seq stfsm_seq_read_jedec = {
|
||||||
|
|
|
||||||
Загрузка…
Ссылка в новой задаче