Merge branch 'ib-extcon-drm-dt-v4.17' into extcon-next

Documentation/devicetree/bindings/connector/samsung,usb-connector-11pin.txt

@@ -0,0 +1,49 @@
+Samsung micro-USB 11-pin connector
+==================================
+
+Samsung micro-USB 11-pin connector is an extension of micro-USB connector.
+It is present in multiple Samsung mobile devices.
+It has additional pins to route MHL traffic simultanously with USB.
+
+The bindings are superset of usb-connector bindings for micro-USB connector[1].
+
+Required properties:
+- compatible: must be: "samsung,usb-connector-11pin", "usb-b-connector",
+- type: must be "micro".
+
+Required nodes:
+- any data bus to the connector should be modeled using the OF graph bindings
+  specified in bindings/graph.txt, unless the bus is between parent node and
+  the connector. Since single connector can have multpile data buses every bus
+  has assigned OF graph port number as follows:
+    0: High Speed (HS),
+    3: Mobile High-Definition Link (MHL), specific to 11-pin Samsung micro-USB.
+
+[1]: bindings/connector/usb-connector.txt
+
+Example
+-------
+
+Micro-USB connector with HS lines routed via controller (MUIC) and MHL lines
+connected to HDMI-MHL bridge (sii8620):
+
+muic-max77843@66 {
+	...
+	usb_con: connector {
+		compatible = "samsung,usb-connector-11pin", "usb-b-connector";
+		label = "micro-USB";
+		type = "micro";
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@3 {
+				reg = <3>;
+				usb_con_mhl: endpoint {
+					remote-endpoint = <&sii8620_mhl>;
+				};
+			};
+		};
+	};
+};

Documentation/devicetree/bindings/connector/usb-connector.txt

@@ -0,0 +1,75 @@
+USB Connector
+=============
+
+USB connector node represents physical USB connector. It should be
+a child of USB interface controller.
+
+Required properties:
+- compatible: describes type of the connector, must be one of:
+    "usb-a-connector",
+    "usb-b-connector",
+    "usb-c-connector".
+
+Optional properties:
+- label: symbolic name for the connector,
+- type: size of the connector, should be specified in case of USB-A, USB-B
+  non-fullsize connectors: "mini", "micro".
+
+Required nodes:
+- any data bus to the connector should be modeled using the OF graph bindings
+  specified in bindings/graph.txt, unless the bus is between parent node and
+  the connector. Since single connector can have multpile data buses every bus
+  has assigned OF graph port number as follows:
+    0: High Speed (HS), present in all connectors,
+    1: Super Speed (SS), present in SS capable connectors,
+    2: Sideband use (SBU), present in USB-C.
+
+Examples
+--------
+
+1. Micro-USB connector with HS lines routed via controller (MUIC):
+
+muic-max77843@66 {
+	...
+	usb_con: connector {
+		compatible = "usb-b-connector";
+		label = "micro-USB";
+		type = "micro";
+	};
+};
+
+2. USB-C connector attached to CC controller (s2mm005), HS lines routed
+to companion PMIC (max77865), SS lines to USB3 PHY and SBU to DisplayPort.
+DisplayPort video lines are routed to the connector via SS mux in USB3 PHY.
+
+ccic: s2mm005@33 {
+	...
+	usb_con: connector {
+		compatible = "usb-c-connector";
+		label = "USB-C";
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				reg = <0>;
+				usb_con_hs: endpoint {
+					remote-endpoint = <&max77865_usbc_hs>;
+				};
+			};
+			port@1 {
+				reg = <1>;
+				usb_con_ss: endpoint {
+					remote-endpoint = <&usbdrd_phy_ss>;
+				};
+			};
+			port@2 {
+				reg = <2>;
+				usb_con_sbu: endpoint {
+					remote-endpoint = <&dp_aux>;
+				};
+			};
+		};
+	};
+};

drivers/extcon/extcon.c

@@ -1336,6 +1336,28 @@ void extcon_dev_unregister(struct extcon_dev *edev)
 EXPORT_SYMBOL_GPL(extcon_dev_unregister);
 
 #ifdef CONFIG_OF
+
+/*
+ * extcon_find_edev_by_node - Find the extcon device from devicetree.
+ * @node	: OF node identifying edev
+ *
+ * Return the pointer of extcon device if success or ERR_PTR(err) if fail.
+ */
+struct extcon_dev *extcon_find_edev_by_node(struct device_node *node)
+{
+	struct extcon_dev *edev;
+
+	mutex_lock(&extcon_dev_list_lock);
+	list_for_each_entry(edev, &extcon_dev_list, entry)
+		if (edev->dev.parent && edev->dev.parent->of_node == node)
+			goto out;
+	edev = ERR_PTR(-EPROBE_DEFER);
+out:
+	mutex_unlock(&extcon_dev_list_lock);
+
+	return edev;
+}
+
 /*
  * extcon_get_edev_by_phandle - Get the extcon device from devicetree.
  * @dev		: the instance to the given device
@@ -1363,25 +1385,27 @@ struct extcon_dev *extcon_get_edev_by_phandle(struct device *dev, int index)
 		return ERR_PTR(-ENODEV);
 	}
 
-	mutex_lock(&extcon_dev_list_lock);
-	list_for_each_entry(edev, &extcon_dev_list, entry) {
-		if (edev->dev.parent && edev->dev.parent->of_node == node) {
-			mutex_unlock(&extcon_dev_list_lock);
-			of_node_put(node);
-			return edev;
-		}
-	}
-	mutex_unlock(&extcon_dev_list_lock);
+	edev = extcon_find_edev_by_node(node);
 	of_node_put(node);
 
-	return ERR_PTR(-EPROBE_DEFER);
+	return edev;
 }
+
 #else
+
+struct extcon_dev *extcon_find_edev_by_node(struct device_node *node)
+{
+	return ERR_PTR(-ENOSYS);
+}
+
 struct extcon_dev *extcon_get_edev_by_phandle(struct device *dev, int index)
 {
 	return ERR_PTR(-ENOSYS);
 }
+
 #endif /* CONFIG_OF */
+
+EXPORT_SYMBOL_GPL(extcon_find_edev_by_node);
 EXPORT_SYMBOL_GPL(extcon_get_edev_by_phandle);
 
 /**

drivers/gpu/drm/bridge/sil-sii8620.c

@@ -17,6 +17,7 @@
 
 #include <linux/clk.h>
 #include <linux/delay.h>
+#include <linux/extcon.h>
 #include <linux/gpio/consumer.h>
 #include <linux/i2c.h>
 #include <linux/interrupt.h>
@@ -25,6 +26,7 @@
 #include <linux/list.h>
 #include <linux/module.h>
 #include <linux/mutex.h>
+#include <linux/of_graph.h>
 #include <linux/regulator/consumer.h>
 #include <linux/slab.h>
 
@@ -81,6 +83,10 @@ struct sii8620 {
 	struct edid *edid;
 	unsigned int gen2_write_burst:1;
 	enum sii8620_mt_state mt_state;
+	struct extcon_dev *extcon;
+	struct notifier_block extcon_nb;
+	struct work_struct extcon_wq;
+	int cable_state;
 	struct list_head mt_queue;
 	struct {
 		int r_size;
@@ -2170,6 +2176,77 @@ static void sii8620_init_rcp_input_dev(struct sii8620 *ctx)
 	ctx->rc_dev = rc_dev;
 }
 
+static void sii8620_cable_out(struct sii8620 *ctx)
+{
+	disable_irq(to_i2c_client(ctx->dev)->irq);
+	sii8620_hw_off(ctx);
+}
+
+static void sii8620_extcon_work(struct work_struct *work)
+{
+	struct sii8620 *ctx =
+		container_of(work, struct sii8620, extcon_wq);
+	int state = extcon_get_state(ctx->extcon, EXTCON_DISP_MHL);
+
+	if (state == ctx->cable_state)
+		return;
+
+	ctx->cable_state = state;
+
+	if (state > 0)
+		sii8620_cable_in(ctx);
+	else
+		sii8620_cable_out(ctx);
+}
+
+static int sii8620_extcon_notifier(struct notifier_block *self,
+			unsigned long event, void *ptr)
+{
+	struct sii8620 *ctx =
+		container_of(self, struct sii8620, extcon_nb);
+
+	schedule_work(&ctx->extcon_wq);
+
+	return NOTIFY_DONE;
+}
+
+static int sii8620_extcon_init(struct sii8620 *ctx)
+{
+	struct extcon_dev *edev;
+	struct device_node *musb, *muic;
+	int ret;
+
+	/* get micro-USB connector node */
+	musb = of_graph_get_remote_node(ctx->dev->of_node, 1, -1);
+	/* next get micro-USB Interface Controller node */
+	muic = of_get_next_parent(musb);
+
+	if (!muic) {
+		dev_info(ctx->dev, "no extcon found, switching to 'always on' mode\n");
+		return 0;
+	}
+
+	edev = extcon_find_edev_by_node(muic);
+	of_node_put(muic);
+	if (IS_ERR(edev)) {
+		if (PTR_ERR(edev) == -EPROBE_DEFER)
+			return -EPROBE_DEFER;
+		dev_err(ctx->dev, "Invalid or missing extcon\n");
+		return PTR_ERR(edev);
+	}
+
+	ctx->extcon = edev;
+	ctx->extcon_nb.notifier_call = sii8620_extcon_notifier;
+	INIT_WORK(&ctx->extcon_wq, sii8620_extcon_work);
+	ret = extcon_register_notifier(edev, EXTCON_DISP_MHL, &ctx->extcon_nb);
+	if (ret) {
+		dev_err(ctx->dev, "failed to register notifier for MHL\n");
+		return ret;
+	}
+
+	return 0;
+}
+
 static inline struct sii8620 *bridge_to_sii8620(struct drm_bridge *bridge)
 {
 	return container_of(bridge, struct sii8620, bridge);
@@ -2302,13 +2379,20 @@ static int sii8620_probe(struct i2c_client *client,
 	if (ret)
 		return ret;
 
+	ret = sii8620_extcon_init(ctx);
+	if (ret < 0) {
+		dev_err(ctx->dev, "failed to initialize EXTCON\n");
+		return ret;
+	}
+
 	i2c_set_clientdata(client, ctx);
 
 	ctx->bridge.funcs = &sii8620_bridge_funcs;
 	ctx->bridge.of_node = dev->of_node;
 	drm_bridge_add(&ctx->bridge);
 
-	sii8620_cable_in(ctx);
+	if (!ctx->extcon)
+		sii8620_cable_in(ctx);
 
 	return 0;
 }
@@ -2317,8 +2401,15 @@ static int sii8620_remove(struct i2c_client *client)
 {
 	struct sii8620 *ctx = i2c_get_clientdata(client);
 
-	disable_irq(to_i2c_client(ctx->dev)->irq);
-	sii8620_hw_off(ctx);
+	if (ctx->extcon) {
+		extcon_unregister_notifier(ctx->extcon, EXTCON_DISP_MHL,
+					   &ctx->extcon_nb);
+		flush_work(&ctx->extcon_wq);
+		if (ctx->cable_state > 0)
+			sii8620_cable_out(ctx);
+	} else {
+		sii8620_cable_out(ctx);
+	}
 	drm_bridge_remove(&ctx->bridge);
 
 	return 0;

include/linux/extcon.h

@@ -230,6 +230,7 @@ extern void devm_extcon_unregister_notifier_all(struct device *dev,
  * Following APIs get the extcon_dev from devicetree or by through extcon name.
  */
 extern struct extcon_dev *extcon_get_extcon_dev(const char *extcon_name);
+extern struct extcon_dev *extcon_find_edev_by_node(struct device_node *node);
 extern struct extcon_dev *extcon_get_edev_by_phandle(struct device *dev,
 						     int index);
 
@@ -283,6 +284,11 @@ static inline struct extcon_dev *extcon_get_extcon_dev(const char *extcon_name)
 	return ERR_PTR(-ENODEV);
 }
 
+static inline struct extcon_dev *extcon_find_edev_by_node(struct device_node *node)
+{
+	return ERR_PTR(-ENODEV);
+}
+
 static inline struct extcon_dev *extcon_get_edev_by_phandle(struct device *dev,
 				int index)
 {