ARM: BCM5301X: Add DT for Meraki MR32
add support for the Cisco Meraki MR32.
This is a dual-band enterprise class 802.11ac access point.
The unit was donated by Chris Blake. Thank you!
SoC: Broadcom BCM53016A1 (1 GHz, 2 cores)
RAM: 128 MiB
NAND: 128 MiB Spansion S34ML01G2 (~114 MiB useable)
ETH: 1GBit Ethernet Port - PoE
WIFI1: Broadcom BCM43520 an+ac (2x2:2 - id: 0x4352)
WIFI2: Broadcom BCM43520 bgn (2x2:2 - id: 0x4352)
WIFI3: Broadcom BCM43428 abgn (1x1:1 - id: 43428)
BLE: Broadcom BCM20732 (ttyS1)
LEDS: 1 x Programmable RGB Status LED (driven by a PWM)
1 x White LED (GPIO)
1 x Orange LED Fault Indicator (GPIO)
2 x LAN Activity / Speed LEDs (On the RJ45 Port)
BUTTON: one Reset button
MISC: AT24C64 8KiB EEPROM (i2c - stores Ethernet MAC)
ina219 hardware monitor (i2c)
Kensington Lock
SERIAL:
WARNING: The serial port needs a TTL/RS-232 3V3 level converter!
The Serial setting is 115200-8-N-1. The board has a populated
right angle 1x4 0.1" pinheader.
The pinout is: VCC, RX, TX, GND.
Odd stuff:
- uart0 clock frequency is 62.5 MHz.
- The LEDs are labeled as SYS-LED1 through SYS-LED3
because of the silkscreen on the PCB.
- the original u-boot has been compiled with most functions
and commands disabled. The u-boot env isn't setup properly
either and as a result, the bcm47xxpart probing is not
working. Hence, the nand partitions are specified through a
"fixed-partition" binding.
- The "WICED SMART(TM)" Bluetooth LE 4.0 BCM20732 chip is
connected to uart2 of the SoC. The BCM20732 does not
provide a HCI. So the linux' bluetooth stack is useless.
The mock-up node with the compatible binding and
enable-gpios property is provided solely as documentation.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
This commit is contained in:
Christian Lamparter
Florian Fainelli
Родитель
c4cd6fcae4
Коммит
ec88a9c344
|
|
@ -127,6 +127,7 @@ dtb-$(CONFIG_ARCH_BCM_5301X) += \
|
|||
bcm47094-luxul-xwr-3150-v1.dtb \
|
||||
bcm47094-netgear-r8500.dtb \
|
||||
bcm47094-phicomm-k3.dtb \
|
||||
bcm53016-meraki-mr32.dtb \
|
||||
bcm94708.dtb \
|
||||
bcm94709.dtb \
|
||||
bcm953012er.dtb \
|
||||
|
|
|
|||
|
|
@ -0,0 +1,197 @@
|
|||
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
||||
/*
|
||||
* Broadcom BCM470X / BCM5301X ARM platform code.
|
||||
* DTS for Meraki MR32 / Codename: Espresso
|
||||
*
|
||||
* Copyright (C) 2018-2020 Christian Lamparter <chunkeey@gmail.com>
|
||||
*/
|
||||
|
||||
/dts-v1/;
|
||||
|
||||
#include "bcm4708.dtsi"
|
||||
#include "bcm5301x-nand-cs0-bch8.dtsi"
|
||||
#include <dt-bindings/leds/common.h>
|
||||
|
||||
/ {
|
||||
compatible = "meraki,mr32", "brcm,brcm53016", "brcm,bcm4708";
|
||||
model = "Meraki MR32";
|
||||
|
||||
chosen {
|
||||
bootargs = " console=ttyS0,115200n8 earlycon";
|
||||
};
|
||||
|
||||
memory {
|
||||
reg = <0x00000000 0x08000000>;
|
||||
device_type = "memory";
|
||||
};
|
||||
|
||||
aliases {
|
||||
serial1 = &uart2;
|
||||
};
|
||||
|
||||
leds {
|
||||
compatible = "gpio-leds";
|
||||
|
||||
sysled3 {
|
||||
function = LED_FUNCTION_FAULT;
|
||||
color = <LED_COLOR_ID_AMBER>;
|
||||
gpios = <&chipcommon 18 GPIO_ACTIVE_LOW>;
|
||||
panic-indicator;
|
||||
};
|
||||
sysled2 {
|
||||
function = LED_FUNCTION_INDICATOR;
|
||||
color = <LED_COLOR_ID_WHITE>;
|
||||
gpios = <&chipcommon 19 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
};
|
||||
|
||||
keys {
|
||||
compatible = "gpio-keys";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
|
||||
restart {
|
||||
label = "Reset";
|
||||
linux,code = <KEY_RESTART>;
|
||||
gpios = <&chipcommon 21 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
};
|
||||
|
||||
pwm-leds {
|
||||
compatible = "pwm-leds";
|
||||
|
||||
red {
|
||||
/* SYS-LED 1 - Tricolor */
|
||||
function = LED_FUNCTION_INDICATOR;
|
||||
color = <LED_COLOR_ID_RED>;
|
||||
pwms = <&pwm 0 50000 0>;
|
||||
max-brightness = <255>;
|
||||
};
|
||||
|
||||
green {
|
||||
/* SYS-LED 1 - Tricolor */
|
||||
function = LED_FUNCTION_POWER;
|
||||
color = <LED_COLOR_ID_GREEN>;
|
||||
pwms = <&pwm 1 50000 0>;
|
||||
max-brightness = <255>;
|
||||
};
|
||||
|
||||
blue {
|
||||
/* SYS-LED 1 - Tricolor */
|
||||
function = LED_FUNCTION_INDICATOR;
|
||||
color = <LED_COLOR_ID_BLUE>;
|
||||
pwms = <&pwm 2 50000 0>;
|
||||
max-brightness = <255>;
|
||||
};
|
||||
};
|
||||
|
||||
i2c {
|
||||
/*
|
||||
* The platform provided I2C does not budge.
|
||||
* This is a replacement until I can figure
|
||||
* out what are the missing bits...
|
||||
*/
|
||||
|
||||
compatible = "i2c-gpio";
|
||||
sda-gpios = <&chipcommon 5 GPIO_ACTIVE_HIGH>;
|
||||
scl-gpios = <&chipcommon 4 GPIO_ACTIVE_HIGH>;
|
||||
i2c-gpio,delay-us = <10>; /* close to 100 kHz */
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
|
||||
current_sense: ina219@45 {
|
||||
compatible = "ti,ina219";
|
||||
reg = <0x45>;
|
||||
shunt-resistor = <60000>; /* = 60 mOhms */
|
||||
};
|
||||
|
||||
eeprom: eeprom@50 {
|
||||
compatible = "atmel,24c64";
|
||||
reg = <0x50>;
|
||||
pagesize = <32>;
|
||||
read-only;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&uart0 {
|
||||
clock-frequency = <62500000>;
|
||||
/delete-property/ clocks;
|
||||
};
|
||||
|
||||
&uart1 {
|
||||
status = "disabled";
|
||||
};
|
||||
|
||||
&uart2 {
|
||||
status = "okay";
|
||||
/*
|
||||
* bluetooth-le {
|
||||
* compatible = "brcm,bcm20732";
|
||||
* enable-gpios = <&chipcommon 20 GPIO_ACTIVE_HIGH>;
|
||||
*};
|
||||
*/
|
||||
};
|
||||
|
||||
&gmac1 {
|
||||
status = "disabled";
|
||||
};
|
||||
&gmac2 {
|
||||
status = "disabled";
|
||||
};
|
||||
&gmac3 {
|
||||
status = "disabled";
|
||||
};
|
||||
|
||||
&pwm {
|
||||
status = "okay";
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&pinmux_pwm>;
|
||||
};
|
||||
|
||||
&nandcs {
|
||||
nand-ecc-algo = "hw";
|
||||
|
||||
partitions {
|
||||
/*
|
||||
* The partition autodetection does not work for this device.
|
||||
* It will only detect the "nvram" partition with an incorrect size.
|
||||
* [ 1.721667] 1 bcm47xxpart partitions found on MTD device brcmnand.0
|
||||
* [ 1.727962] Creating 1 MTD partitions on "brcmnand.0":
|
||||
* [ 1.733117] 0x000000400000-0x000008000000 : "nvram"
|
||||
*/
|
||||
|
||||
compatible = "fixed-partitions";
|
||||
#address-cells = <0x1>;
|
||||
#size-cells = <0x1>;
|
||||
|
||||
partition0@0 {
|
||||
label = "u-boot";
|
||||
reg = <0x0 0x100000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition1@100000 {
|
||||
label = "bootkernel1";
|
||||
reg = <0x100000 0x300000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition2@400000 {
|
||||
label = "nvram";
|
||||
reg = <0x400000 0x100000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition3@500000 {
|
||||
label = "bootkernel2";
|
||||
reg = <0x500000 0x300000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition4@800000 {
|
||||
label = "ubi";
|
||||
reg = <0x800000 0x7780000>;
|
||||
};
|
||||
};
|
||||
};
|
||||
Загрузка…
Ссылка в новой задаче