Merge 3.10-rc3 into char-misc-next

We want the changes in here.

Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Documentation/devicetree/bindings/net/macb.txt

@@ -4,7 +4,7 @@ Required properties:
 - compatible: Should be "cdns,[<chip>-]{macb|gem}"
   Use "cdns,at91sam9260-macb" Atmel at91sam9260 and at91sam9263 SoCs.
   Use "cdns,at32ap7000-macb" for other 10/100 usage or use the generic form: "cdns,macb".
-  Use "cnds,pc302-gem" for Picochip picoXcell pc302 and later devices based on
+  Use "cdns,pc302-gem" for Picochip picoXcell pc302 and later devices based on
   the Cadence GEM, or the generic form: "cdns,gem".
 - reg: Address and length of the register set for the device
 - interrupts: Should contain macb interrupt

Documentation/devicetree/bindings/video/simple-framebuffer.txt

@@ -0,0 +1,25 @@
+Simple Framebuffer
+
+A simple frame-buffer describes a raw memory region that may be rendered to,
+with the assumption that the display hardware has already been set up to scan
+out from that buffer.
+
+Required properties:
+- compatible: "simple-framebuffer"
+- reg: Should contain the location and size of the framebuffer memory.
+- width: The width of the framebuffer in pixels.
+- height: The height of the framebuffer in pixels.
+- stride: The number of bytes in each line of the framebuffer.
+- format: The format of the framebuffer surface. Valid values are:
+  - r5g6b5 (16-bit pixels, d[15:11]=r, d[10:5]=g, d[4:0]=b).
+
+Example:
+
+	framebuffer {
+		compatible = "simple-framebuffer";
+		reg = <0x1d385000 (1600 * 1200 * 2)>;
+		width = <1600>;
+		height = <1200>;
+		stride = <(1600 * 2)>;
+		format = "r5g6b5";
+	};

Documentation/devicetree/usage-model.txt

@@ -191,9 +191,11 @@ Linux it will look something like this:
 	};
 
 The bootargs property contains the kernel arguments, and the initrd-*
-properties define the address and size of an initrd blob.  The
-chosen node may also optionally contain an arbitrary number of
-additional properties for platform-specific configuration data.
+properties define the address and size of an initrd blob.  Note that
+initrd-end is the first address after the initrd image, so this doesn't
+match the usual semantic of struct resource.  The chosen node may also
+optionally contain an arbitrary number of additional properties for
+platform-specific configuration data.
 
 During early boot, the architecture setup code calls of_scan_flat_dt()
 several times with different helper callbacks to parse device tree

Documentation/kernel-parameters.txt

@@ -3005,6 +3005,27 @@ bytes respectively. Such letter suffixes can also be entirely omitted.
 			Force threading of all interrupt handlers except those
 			marked explicitly IRQF_NO_THREAD.
 
+	tmem		[KNL,XEN]
+			Enable the Transcendent memory driver if built-in.
+
+	tmem.cleancache=0|1 [KNL, XEN]
+			Default is on (1). Disable the usage of the cleancache
+			API to send anonymous pages to the hypervisor.
+
+	tmem.frontswap=0|1 [KNL, XEN]
+			Default is on (1). Disable the usage of the frontswap
+			API to send swap pages to the hypervisor. If disabled
+			the selfballooning and selfshrinking are force disabled.
+
+	tmem.selfballooning=0|1 [KNL, XEN]
+			Default is on (1). Disable the driving of swap pages
+			to the hypervisor.
+
+	tmem.selfshrinking=0|1 [KNL, XEN]
+			Default is on (1). Partial swapoff that immediately
+			transfers pages from Xen hypervisor back to the
+			kernel based on different criteria.
+
 	topology=	[S390]
 			Format: {off | on}
 			Specify if the kernel should make use of the cpu

Documentation/kernel-per-CPU-kthreads.txt

@@ -0,0 +1,202 @@
+REDUCING OS JITTER DUE TO PER-CPU KTHREADS
+
+This document lists per-CPU kthreads in the Linux kernel and presents
+options to control their OS jitter.  Note that non-per-CPU kthreads are
+not listed here.  To reduce OS jitter from non-per-CPU kthreads, bind
+them to a "housekeeping" CPU dedicated to such work.
+
+
+REFERENCES
+
+o	Documentation/IRQ-affinity.txt:  Binding interrupts to sets of CPUs.
+
+o	Documentation/cgroups:  Using cgroups to bind tasks to sets of CPUs.
+
+o	man taskset:  Using the taskset command to bind tasks to sets
+	of CPUs.
+
+o	man sched_setaffinity:  Using the sched_setaffinity() system
+	call to bind tasks to sets of CPUs.
+
+o	/sys/devices/system/cpu/cpuN/online:  Control CPU N's hotplug state,
+	writing "0" to offline and "1" to online.
+
+o	In order to locate kernel-generated OS jitter on CPU N:
+
+		cd /sys/kernel/debug/tracing
+		echo 1 > max_graph_depth # Increase the "1" for more detail
+		echo function_graph > current_tracer
+		# run workload
+		cat per_cpu/cpuN/trace
+
+
+KTHREADS
+
+Name: ehca_comp/%u
+Purpose: Periodically process Infiniband-related work.
+To reduce its OS jitter, do any of the following:
+1.	Don't use eHCA Infiniband hardware, instead choosing hardware
+	that does not require per-CPU kthreads.  This will prevent these
+	kthreads from being created in the first place.  (This will
+	work for most people, as this hardware, though important, is
+	relatively old and is produced in relatively low unit volumes.)
+2.	Do all eHCA-Infiniband-related work on other CPUs, including
+	interrupts.
+3.	Rework the eHCA driver so that its per-CPU kthreads are
+	provisioned only on selected CPUs.
+
+
+Name: irq/%d-%s
+Purpose: Handle threaded interrupts.
+To reduce its OS jitter, do the following:
+1.	Use irq affinity to force the irq threads to execute on
+	some other CPU.
+
+Name: kcmtpd_ctr_%d
+Purpose: Handle Bluetooth work.
+To reduce its OS jitter, do one of the following:
+1.	Don't use Bluetooth, in which case these kthreads won't be
+	created in the first place.
+2.	Use irq affinity to force Bluetooth-related interrupts to
+	occur on some other CPU and furthermore initiate all
+	Bluetooth activity on some other CPU.
+
+Name: ksoftirqd/%u
+Purpose: Execute softirq handlers when threaded or when under heavy load.
+To reduce its OS jitter, each softirq vector must be handled
+separately as follows:
+TIMER_SOFTIRQ:  Do all of the following:
+1.	To the extent possible, keep the CPU out of the kernel when it
+	is non-idle, for example, by avoiding system calls and by forcing
+	both kernel threads and interrupts to execute elsewhere.
+2.	Build with CONFIG_HOTPLUG_CPU=y.  After boot completes, force
+	the CPU offline, then bring it back online.  This forces
+	recurring timers to migrate elsewhere.	If you are concerned
+	with multiple CPUs, force them all offline before bringing the
+	first one back online.  Once you have onlined the CPUs in question,
+	do not offline any other CPUs, because doing so could force the
+	timer back onto one of the CPUs in question.
+NET_TX_SOFTIRQ and NET_RX_SOFTIRQ:  Do all of the following:
+1.	Force networking interrupts onto other CPUs.
+2.	Initiate any network I/O on other CPUs.
+3.	Once your application has started, prevent CPU-hotplug operations
+	from being initiated from tasks that might run on the CPU to
+	be de-jittered.  (It is OK to force this CPU offline and then
+	bring it back online before you start your application.)
+BLOCK_SOFTIRQ:  Do all of the following:
+1.	Force block-device interrupts onto some other CPU.
+2.	Initiate any block I/O on other CPUs.
+3.	Once your application has started, prevent CPU-hotplug operations
+	from being initiated from tasks that might run on the CPU to
+	be de-jittered.  (It is OK to force this CPU offline and then
+	bring it back online before you start your application.)
+BLOCK_IOPOLL_SOFTIRQ:  Do all of the following:
+1.	Force block-device interrupts onto some other CPU.
+2.	Initiate any block I/O and block-I/O polling on other CPUs.
+3.	Once your application has started, prevent CPU-hotplug operations
+	from being initiated from tasks that might run on the CPU to
+	be de-jittered.  (It is OK to force this CPU offline and then
+	bring it back online before you start your application.)
+TASKLET_SOFTIRQ: Do one or more of the following:
+1.	Avoid use of drivers that use tasklets.  (Such drivers will contain
+	calls to things like tasklet_schedule().)
+2.	Convert all drivers that you must use from tasklets to workqueues.
+3.	Force interrupts for drivers using tasklets onto other CPUs,
+	and also do I/O involving these drivers on other CPUs.
+SCHED_SOFTIRQ: Do all of the following:
+1.	Avoid sending scheduler IPIs to the CPU to be de-jittered,
+	for example, ensure that at most one runnable kthread is present
+	on that CPU.  If a thread that expects to run on the de-jittered
+	CPU awakens, the scheduler will send an IPI that can result in
+	a subsequent SCHED_SOFTIRQ.
+2.	Build with CONFIG_RCU_NOCB_CPU=y, CONFIG_RCU_NOCB_CPU_ALL=y,
+	CONFIG_NO_HZ_FULL=y, and, in addition, ensure that the CPU
+	to be de-jittered is marked as an adaptive-ticks CPU using the
+	"nohz_full=" boot parameter.  This reduces the number of
+	scheduler-clock interrupts that the de-jittered CPU receives,
+	minimizing its chances of being selected to do the load balancing
+	work that runs in SCHED_SOFTIRQ context.
+3.	To the extent possible, keep the CPU out of the kernel when it
+	is non-idle, for example, by avoiding system calls and by
+	forcing both kernel threads and interrupts to execute elsewhere.
+	This further reduces the number of scheduler-clock interrupts
+	received by the de-jittered CPU.
+HRTIMER_SOFTIRQ:  Do all of the following:
+1.	To the extent possible, keep the CPU out of the kernel when it
+	is non-idle.  For example, avoid system calls and force both
+	kernel threads and interrupts to execute elsewhere.
+2.	Build with CONFIG_HOTPLUG_CPU=y.  Once boot completes, force the
+	CPU offline, then bring it back online.  This forces recurring
+	timers to migrate elsewhere.  If you are concerned with multiple
+	CPUs, force them all offline before bringing the first one
+	back online.  Once you have onlined the CPUs in question, do not
+	offline any other CPUs, because doing so could force the timer
+	back onto one of the CPUs in question.
+RCU_SOFTIRQ:  Do at least one of the following:
+1.	Offload callbacks and keep the CPU in either dyntick-idle or
+	adaptive-ticks state by doing all of the following:
+	a.	Build with CONFIG_RCU_NOCB_CPU=y, CONFIG_RCU_NOCB_CPU_ALL=y,
+		CONFIG_NO_HZ_FULL=y, and, in addition ensure that the CPU
+		to be de-jittered is marked as an adaptive-ticks CPU using
+		the "nohz_full=" boot parameter.  Bind the rcuo kthreads
+		to housekeeping CPUs, which can tolerate OS jitter.
+	b.	To the extent possible, keep the CPU out of the kernel
+		when it is non-idle, for example, by avoiding system
+		calls and by forcing both kernel threads and interrupts
+		to execute elsewhere.
+2.	Enable RCU to do its processing remotely via dyntick-idle by
+	doing all of the following:
+	a.	Build with CONFIG_NO_HZ=y and CONFIG_RCU_FAST_NO_HZ=y.
+	b.	Ensure that the CPU goes idle frequently, allowing other
+		CPUs to detect that it has passed through an RCU quiescent
+		state.	If the kernel is built with CONFIG_NO_HZ_FULL=y,
+		userspace execution also allows other CPUs to detect that
+		the CPU in question has passed through a quiescent state.
+	c.	To the extent possible, keep the CPU out of the kernel
+		when it is non-idle, for example, by avoiding system
+		calls and by forcing both kernel threads and interrupts
+		to execute elsewhere.
+
+Name: rcuc/%u
+Purpose: Execute RCU callbacks in CONFIG_RCU_BOOST=y kernels.
+To reduce its OS jitter, do at least one of the following:
+1.	Build the kernel with CONFIG_PREEMPT=n.  This prevents these
+	kthreads from being created in the first place, and also obviates
+	the need for RCU priority boosting.  This approach is feasible
+	for workloads that do not require high degrees of responsiveness.
+2.	Build the kernel with CONFIG_RCU_BOOST=n.  This prevents these
+	kthreads from being created in the first place.  This approach
+	is feasible only if your workload never requires RCU priority
+	boosting, for example, if you ensure frequent idle time on all
+	CPUs that might execute within the kernel.
+3.	Build with CONFIG_RCU_NOCB_CPU=y and CONFIG_RCU_NOCB_CPU_ALL=y,
+	which offloads all RCU callbacks to kthreads that can be moved
+	off of CPUs susceptible to OS jitter.  This approach prevents the
+	rcuc/%u kthreads from having any work to do, so that they are
+	never awakened.
+4.	Ensure that the CPU never enters the kernel, and, in particular,
+	avoid initiating any CPU hotplug operations on this CPU.  This is
+	another way of preventing any callbacks from being queued on the
+	CPU, again preventing the rcuc/%u kthreads from having any work
+	to do.
+
+Name: rcuob/%d, rcuop/%d, and rcuos/%d
+Purpose: Offload RCU callbacks from the corresponding CPU.
+To reduce its OS jitter, do at least one of the following:
+1.	Use affinity, cgroups, or other mechanism to force these kthreads
+	to execute on some other CPU.
+2.	Build with CONFIG_RCU_NOCB_CPUS=n, which will prevent these
+	kthreads from being created in the first place.  However, please
+	note that this will not eliminate OS jitter, but will instead
+	shift it to RCU_SOFTIRQ.
+
+Name: watchdog/%u
+Purpose: Detect software lockups on each CPU.
+To reduce its OS jitter, do at least one of the following:
+1.	Build with CONFIG_LOCKUP_DETECTOR=n, which will prevent these
+	kthreads from being created in the first place.
+2.	Echo a zero to /proc/sys/kernel/watchdog to disable the
+	watchdog timer.
+3.	Echo a large number of /proc/sys/kernel/watchdog_thresh in
+	order to reduce the frequency of OS jitter due to the watchdog
+	timer down to a level that is acceptable for your workload.

Documentation/power/devices.txt

@@ -268,7 +268,7 @@ situations.
 System Power Management Phases
 ------------------------------
 Suspending or resuming the system is done in several phases.  Different phases
-are used for standby or memory sleep states ("suspend-to-RAM") and the
+are used for freeze, standby, and memory sleep states ("suspend-to-RAM") and the
 hibernation state ("suspend-to-disk").  Each phase involves executing callbacks
 for every device before the next phase begins.  Not all busses or classes
 support all these callbacks and not all drivers use all the callbacks.  The
@@ -309,7 +309,8 @@ execute the corresponding method from dev->driver->pm instead if there is one.
 
 Entering System Suspend
 -----------------------
-When the system goes into the standby or memory sleep state, the phases are:
+When the system goes into the freeze, standby or memory sleep state,
+the phases are:
 
 		prepare, suspend, suspend_late, suspend_noirq.
 
@@ -368,7 +369,7 @@ the devices that were suspended.
 
 Leaving System Suspend
 ----------------------
-When resuming from standby or memory sleep, the phases are:
+When resuming from freeze, standby or memory sleep, the phases are:
 
 		resume_noirq, resume_early, resume, complete.
 
@@ -433,8 +434,8 @@ the system log.
 
 Entering Hibernation
 --------------------
-Hibernating the system is more complicated than putting it into the standby or
-memory sleep state, because it involves creating and saving a system image.
+Hibernating the system is more complicated than putting it into the other
+sleep states, because it involves creating and saving a system image.
 Therefore there are more phases for hibernation, with a different set of
 callbacks.  These phases always run after tasks have been frozen and memory has
 been freed.
@@ -485,8 +486,8 @@ image forms an atomic snapshot of the system state.
 
 At this point the system image is saved, and the devices then need to be
 prepared for the upcoming system shutdown.  This is much like suspending them
-before putting the system into the standby or memory sleep state, and the phases
-are similar.
+before putting the system into the freeze, standby or memory sleep state,
+and the phases are similar.
 
     9.	The prepare phase is discussed above.
 

Documentation/power/interface.txt

@@ -7,8 +7,8 @@ running. The interface exists in /sys/power/ directory (assuming sysfs
 is mounted at /sys). 
 
 /sys/power/state controls system power state. Reading from this file
-returns what states are supported, which is hard-coded to 'standby'
-(Power-On Suspend), 'mem' (Suspend-to-RAM), and 'disk'
+returns what states are supported, which is hard-coded to 'freeze',
+'standby' (Power-On Suspend), 'mem' (Suspend-to-RAM), and 'disk'
 (Suspend-to-Disk). 
 
 Writing to this file one of those strings causes the system to

Documentation/power/notifiers.txt

@@ -15,8 +15,10 @@ A suspend/hibernation notifier may be used for this purpose.
 The subsystems or drivers having such needs can register suspend notifiers that
 will be called upon the following events by the PM core:
 
-PM_HIBERNATION_PREPARE	The system is going to hibernate or suspend, tasks will
-			be frozen immediately.
+PM_HIBERNATION_PREPARE	The system is going to hibernate, tasks will be frozen
+			immediately. This is different from PM_SUSPEND_PREPARE
+			below because here we do additional work between notifiers
+			and drivers freezing.
 
 PM_POST_HIBERNATION	The system memory state has been restored from a
 			hibernation image or an error occurred during

Documentation/power/states.txt

@@ -2,12 +2,26 @@
 System Power Management States
 
 
-The kernel supports three power management states generically, though
-each is dependent on platform support code to implement the low-level
-details for each state. This file describes each state, what they are
+The kernel supports four power management states generically, though
+one is generic and the other three are dependent on platform support
+code to implement the low-level details for each state.
+This file describes each state, what they are
 commonly called, what ACPI state they map to, and what string to write
 to /sys/power/state to enter that state
 
+state:		Freeze / Low-Power Idle
+ACPI state:	S0
+String:		"freeze"
+
+This state is a generic, pure software, light-weight, low-power state.
+It allows more energy to be saved relative to idle by freezing user
+space and putting all I/O devices into low-power states (possibly
+lower-power than available at run time), such that the processors can
+spend more time in their idle states.
+This state can be used for platforms without Standby/Suspend-to-RAM
+support, or it can be used in addition to Suspend-to-RAM (memory sleep)
+to provide reduced resume latency.
+
 
 State:		Standby / Power-On Suspend
 ACPI State:	S1
@@ -22,9 +36,6 @@ We try to put devices in a low-power state equivalent to D1, which
 also offers low power savings, but low resume latency. Not all devices
 support D1, and those that don't are left on. 
 
-A transition from Standby to the On state should take about 1-2
-seconds. 
-
 
 State:		Suspend-to-RAM
 ACPI State:	S3
@@ -42,9 +53,6 @@ transition back to the On state.
 For at least ACPI, STR requires some minimal boot-strapping code to
 resume the system from STR. This may be true on other platforms. 
 
-A transition from Suspend-to-RAM to the On state should take about
-3-5 seconds. 
-
 
 State:		Suspend-to-disk
 ACPI State:	S4
@@ -74,7 +82,3 @@ low-power state (like ACPI S4), or it may simply power down. Powering
 down offers greater savings, and allows this mechanism to work on any
 system. However, entering a real low-power state allows the user to
 trigger wake up events (e.g. pressing a key or opening a laptop lid).
-
-A transition from Suspend-to-Disk to the On state should take about 30
-seconds, though it's typically a bit more with the current
-implementation. 

Documentation/rapidio/rapidio.txt

@@ -79,20 +79,63 @@ master port that is used to communicate with devices within the network.
 In order to initialize the RapidIO subsystem, a platform must initialize and
 register at least one master port within the RapidIO network. To register mport
 within the subsystem controller driver initialization code calls function
-rio_register_mport() for each available master port. After all active master
-ports are registered with a RapidIO subsystem, the rio_init_mports() routine
-is called to perform enumeration and discovery.
+rio_register_mport() for each available master port.
 
-In the current PowerPC-based implementation a subsys_initcall() is specified to
-perform controller initialization and mport registration. At the end it directly
-calls rio_init_mports() to execute RapidIO enumeration and discovery.
+RapidIO subsystem uses subsys_initcall() or device_initcall() to perform
+controller initialization (depending on controller device type).
+
+After all active master ports are registered with a RapidIO subsystem,
+an enumeration and/or discovery routine may be called automatically or
+by user-space command.
 
 4. Enumeration and Discovery
 ----------------------------
 
-When rio_init_mports() is called it scans a list of registered master ports and
-calls an enumeration or discovery routine depending on the configured role of a
-master port: host or agent.
+4.1 Overview
+------------
+
+RapidIO subsystem configuration options allow users to specify enumeration and
+discovery methods as statically linked components or loadable modules.
+An enumeration/discovery method implementation and available input parameters
+define how any given method can be attached to available RapidIO mports:
+simply to all available mports OR individually to the specified mport device.
+
+Depending on selected enumeration/discovery build configuration, there are
+several methods to initiate an enumeration and/or discovery process:
+
+  (a) Statically linked enumeration and discovery process can be started
+  automatically during kernel initialization time using corresponding module
+  parameters. This was the original method used since introduction of RapidIO
+  subsystem. Now this method relies on enumerator module parameter which is
+  'rio-scan.scan' for existing basic enumeration/discovery method.
+  When automatic start of enumeration/discovery is used a user has to ensure
+  that all discovering endpoints are started before the enumerating endpoint
+  and are waiting for enumeration to be completed.
+  Configuration option CONFIG_RAPIDIO_DISC_TIMEOUT defines time that discovering
+  endpoint waits for enumeration to be completed. If the specified timeout
+  expires the discovery process is terminated without obtaining RapidIO network
+  information. NOTE: a timed out discovery process may be restarted later using
+  a user-space command as it is described later if the given endpoint was
+  enumerated successfully.
+
+  (b) Statically linked enumeration and discovery process can be started by
+  a command from user space. This initiation method provides more flexibility
+  for a system startup compared to the option (a) above. After all participating
+  endpoints have been successfully booted, an enumeration process shall be
+  started first by issuing a user-space command, after an enumeration is
+  completed a discovery process can be started on all remaining endpoints.
+
+  (c) Modular enumeration and discovery process can be started by a command from
+  user space. After an enumeration/discovery module is loaded, a network scan
+  process can be started by issuing a user-space command.
+  Similar to the option (b) above, an enumerator has to be started first.
+
+  (d) Modular enumeration and discovery process can be started by a module
+  initialization routine. In this case an enumerating module shall be loaded
+  first.
+
+When a network scan process is started it calls an enumeration or discovery
+routine depending on the configured role of a master port: host or agent.
 
 Enumeration is performed by a master port if it is configured as a host port by
 assigning a host device ID greater than or equal to zero. A host device ID is
@@ -104,8 +147,58 @@ for it.
 The enumeration and discovery routines use RapidIO maintenance transactions
 to access the configuration space of devices.
 
-The enumeration process is implemented according to the enumeration algorithm
-outlined in the RapidIO Interconnect Specification: Annex I [1].
+4.2 Automatic Start of Enumeration and Discovery
+------------------------------------------------
+
+Automatic enumeration/discovery start method is applicable only to built-in
+enumeration/discovery RapidIO configuration selection. To enable automatic
+enumeration/discovery start by existing basic enumerator method set use boot
+command line parameter "rio-scan.scan=1".
+
+This configuration requires synchronized start of all RapidIO endpoints that
+form a network which will be enumerated/discovered. Discovering endpoints have
+to be started before an enumeration starts to ensure that all RapidIO
+controllers have been initialized and are ready to be discovered. Configuration
+parameter CONFIG_RAPIDIO_DISC_TIMEOUT defines time (in seconds) which
+a discovering endpoint will wait for enumeration to be completed.
+
+When automatic enumeration/discovery start is selected, basic method's
+initialization routine calls rio_init_mports() to perform enumeration or
+discovery for all known mport devices.
+
+Depending on RapidIO network size and configuration this automatic
+enumeration/discovery start method may be difficult to use due to the
+requirement for synchronized start of all endpoints.
+
+4.3 User-space Start of Enumeration and Discovery
+-------------------------------------------------
+
+User-space start of enumeration and discovery can be used with built-in and
+modular build configurations. For user-space controlled start RapidIO subsystem
+creates the sysfs write-only attribute file '/sys/bus/rapidio/scan'. To initiate
+an enumeration or discovery process on specific mport device, a user needs to
+write mport_ID (not RapidIO destination ID) into that file. The mport_ID is a
+sequential number (0 ... RIO_MAX_MPORTS) assigned during mport device
+registration. For example for machine with single RapidIO controller, mport_ID
+for that controller always will be 0.
+
+To initiate RapidIO enumeration/discovery on all available mports a user may
+write '-1' (or RIO_MPORT_ANY) into the scan attribute file.
+
+4.4 Basic Enumeration Method
+----------------------------
+
+This is an original enumeration/discovery method which is available since
+first release of RapidIO subsystem code. The enumeration process is
+implemented according to the enumeration algorithm outlined in the RapidIO
+Interconnect Specification: Annex I [1].
+
+This method can be configured as statically linked or loadable module.
+The method's single parameter "scan" allows to trigger the enumeration/discovery
+process from module initialization routine.
+
+This enumeration/discovery method can be started only once and does not support
+unloading if it is built as a module.
 
 The enumeration process traverses the network using a recursive depth-first
 algorithm. When a new device is found, the enumerator takes ownership of that
@@ -160,6 +253,19 @@ time period. If this wait time period expires before enumeration is completed,
 an agent skips RapidIO discovery and continues with remaining kernel
 initialization.
 
+4.5 Adding New Enumeration/Discovery Method
+-------------------------------------------
+
+RapidIO subsystem code organization allows addition of new enumeration/discovery
+methods as new configuration options without significant impact to to the core
+RapidIO code.
+
+A new enumeration/discovery method has to be attached to one or more mport
+devices before an enumeration/discovery process can be started. Normally,
+method's module initialization routine calls rio_register_scan() to attach
+an enumerator to a specified mport device (or devices). The basic enumerator
+implementation demonstrates this process.
+
 5. References
 -------------
 

Documentation/rapidio/sysfs.txt

@@ -88,3 +88,20 @@ that exports additional attributes.
 
 IDT_GEN2:
  errlog - reads contents of device error log until it is empty.
+
+
+5. RapidIO Bus Attributes
+-------------------------
+
+RapidIO bus subdirectory /sys/bus/rapidio implements the following bus-specific
+attribute:
+
+  scan - allows to trigger enumeration discovery process from user space. This
+	 is a write-only attribute. To initiate an enumeration or discovery
+	 process on specific mport device, a user needs to write mport_ID (not
+	 RapidIO destination ID) into this file. The mport_ID is a sequential
+	 number (0 ... RIO_MAX_MPORTS) assigned to the mport device.
+	 For example, for a machine with a single RapidIO controller, mport_ID
+	 for that controller always will be 0.
+	 To initiate RapidIO enumeration/discovery on all available mports
+	 a user must write '-1' (or RIO_MPORT_ANY) into this attribute file.

MAINTAINERS

@@ -3865,9 +3865,16 @@ M:	K. Y. Srinivasan <kys@microsoft.com>
 M:	Haiyang Zhang <haiyangz@microsoft.com>
 L:	devel@linuxdriverproject.org
 S:	Maintained
-F:	drivers/hv/
+F:	arch/x86/include/asm/mshyperv.h
+F:	arch/x86/include/uapi/asm/hyperv.h
+F:	arch/x86/kernel/cpu/mshyperv.c
 F:	drivers/hid/hid-hyperv.c
+F:	drivers/hv/
 F:	drivers/net/hyperv/
+F:	drivers/scsi/storvsc_drv.c
+F:	drivers/video/hyperv_fb.c
+F:	include/linux/hyperv.h
+F:	tools/hv/
 
 I2C OVER PARALLEL PORT
 M:	Jean Delvare <khali@linux-fr.org>
@@ -4641,12 +4648,13 @@ F:	include/linux/sunrpc/
 F:	include/uapi/linux/sunrpc/
 
 KERNEL VIRTUAL MACHINE (KVM)
-M:	Marcelo Tosatti <mtosatti@redhat.com>
 M:	Gleb Natapov <gleb@redhat.com>
+M:	Paolo Bonzini <pbonzini@redhat.com>
 L:	kvm@vger.kernel.org
-W:	http://kvm.qumranet.com
+W:	http://linux-kvm.org
 S:	Supported
-F:	Documentation/*/kvm.txt
+F:	Documentation/*/kvm*.txt
+F:	Documentation/virtual/kvm/
 F:	arch/*/kvm/
 F:	arch/*/include/asm/kvm*
 F:	include/linux/kvm*
@@ -4976,6 +4984,13 @@ S:	Maintained
 F:	Documentation/hwmon/lm90
 F:	drivers/hwmon/lm90.c
 
+LM95234 HARDWARE MONITOR DRIVER
+M:	Guenter Roeck <linux@roeck-us.net>
+L:	lm-sensors@lm-sensors.org
+S:	Maintained
+F:	Documentation/hwmon/lm95234
+F:	drivers/hwmon/lm95234.c
+
 LME2510 MEDIA DRIVER
 M:	Malcolm Priestley <tvboxspy@gmail.com>
 L:	linux-media@vger.kernel.org
@@ -5509,18 +5524,18 @@ F:	Documentation/networking/s2io.txt
 F:	Documentation/networking/vxge.txt
 F:	drivers/net/ethernet/neterion/
 
-NETFILTER/IPTABLES/IPCHAINS
-P:	Harald Welte
-P:	Jozsef Kadlecsik
+NETFILTER/IPTABLES
 M:	Pablo Neira Ayuso <pablo@netfilter.org>
 M:	Patrick McHardy <kaber@trash.net>
+M:	Jozsef Kadlecsik <kadlec@blackhole.kfki.hu>
 L:	netfilter-devel@vger.kernel.org
 L:	netfilter@vger.kernel.org
 L:	coreteam@netfilter.org
 W:	http://www.netfilter.org/
 W:	http://www.iptables.org/
-T:	git git://1984.lsi.us.es/nf
-T:	git git://1984.lsi.us.es/nf-next
+Q:	http://patchwork.ozlabs.org/project/netfilter-devel/list/
+T:	git git://git.kernel.org/pub/scm/linux/kernel/git/pablo/nf.git
+T:	git git://git.kernel.org/pub/scm/linux/kernel/git/pablo/nf-next.git
 S:	Supported
 F:	include/linux/netfilter*
 F:	include/linux/netfilter/
@@ -6069,6 +6084,7 @@ L:	linux-parisc@vger.kernel.org
 W:	http://www.parisc-linux.org/
 Q:	http://patchwork.kernel.org/project/linux-parisc/list/
 T:	git git://git.kernel.org/pub/scm/linux/kernel/git/jejb/parisc-2.6.git
+T:	git git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux.git
 S:	Maintained
 F:	arch/parisc/
 F:	drivers/parisc/
@@ -7854,7 +7870,7 @@ L:	linux-scsi@vger.kernel.org
 L:	target-devel@vger.kernel.org
 L:	http://groups.google.com/group/linux-iscsi-target-dev
 W:	http://www.linux-iscsi.org
-T:	git git://git.kernel.org/pub/scm/linux/kernel/git/nab/lio-core.git master
+T:	git git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending.git master
 S:	Supported
 F:	drivers/target/
 F:	include/target/
@@ -8182,6 +8198,13 @@ F:	drivers/mmc/host/sh_mobile_sdhi.c
 F:	include/linux/mmc/tmio.h
 F:	include/linux/mmc/sh_mobile_sdhi.h
 
+TMP401 HARDWARE MONITOR DRIVER
+M:	Guenter Roeck <linux@roeck-us.net>
+L:	lm-sensors@lm-sensors.org
+S:	Maintained
+F:	Documentation/hwmon/tmp401
+F:	drivers/hwmon/tmp401.c
+
 TMPFS (SHMEM FILESYSTEM)
 M:	Hugh Dickins <hughd@google.com>
 L:	linux-mm@kvack.org

Makefile

@@ -1,7 +1,7 @@
 VERSION = 3
 PATCHLEVEL = 10
 SUBLEVEL = 0
-EXTRAVERSION = -rc1
+EXTRAVERSION = -rc3
 NAME = Unicycling Gorilla
 
 # *DOCUMENTATION*

arch/Kconfig

@@ -213,6 +213,9 @@ config USE_GENERIC_SMP_HELPERS
 config GENERIC_SMP_IDLE_THREAD
        bool
 
+config GENERIC_IDLE_POLL_SETUP
+       bool
+
 # Select if arch init_task initializer is different to init/init_task.c
 config ARCH_INIT_TASK
        bool

arch/arc/boot/dts/abilis_tb100_dvk.dts

@@ -37,7 +37,7 @@
 
 	soc100 {
 		uart@FF100000 {
-			pinctrl-names = "abilis,simple-default";
+			pinctrl-names = "default";
 			pinctrl-0 = <&pctl_uart0>;
 		};
 		ethernet@FE100000 {

arch/arc/boot/dts/abilis_tb101_dvk.dts

@@ -37,7 +37,7 @@
 
 	soc100 {
 		uart@FF100000 {
-			pinctrl-names = "abilis,simple-default";
+			pinctrl-names = "default";
 			pinctrl-0 = <&pctl_uart0>;
 		};
 		ethernet@FE100000 {

arch/arc/boot/dts/abilis_tb10x.dtsi

@@ -88,8 +88,7 @@
 		};
 
 		uart@FF100000 {
-			compatible = "snps,dw-apb-uart",
-					"abilis,simple-pinctrl";
+			compatible = "snps,dw-apb-uart";
 			reg = <0xFF100000 0x100>;
 			clock-frequency = <166666666>;
 			interrupts = <25 1>;
@@ -184,8 +183,7 @@
 			#address-cells = <1>;
 			#size-cells = <0>;
 			cell-index = <1>;
-			compatible = "abilis,tb100-spi",
-					"abilis,simple-pinctrl";
+			compatible = "abilis,tb100-spi";
 			num-cs = <2>;
 			reg = <0xFE011000 0x20>;
 			interrupt-parent = <&tb10x_ictl>;

arch/arc/include/asm/cacheflush.h

@@ -93,14 +93,16 @@ static inline int cache_is_vipt_aliasing(void)
 #endif
 }
 
-#define CACHE_COLOR(addr)	(((unsigned long)(addr) >> (PAGE_SHIFT)) & 3)
+#define CACHE_COLOR(addr)	(((unsigned long)(addr) >> (PAGE_SHIFT)) & 1)
 
 /*
  * checks if two addresses (after page aligning) index into same cache set
  */
 #define addr_not_cache_congruent(addr1, addr2)				\
+({									\
 	cache_is_vipt_aliasing() ? 					\
-		(CACHE_COLOR(addr1) != CACHE_COLOR(addr2)) : 0		\
+		(CACHE_COLOR(addr1) != CACHE_COLOR(addr2)) : 0;		\
+})
 
 #define copy_to_user_page(vma, page, vaddr, dst, src, len)		\
 do {									\

arch/arc/include/asm/page.h

@@ -19,13 +19,6 @@
 #define clear_page(paddr)		memset((paddr), 0, PAGE_SIZE)
 #define copy_page(to, from)		memcpy((to), (from), PAGE_SIZE)
 
-#ifndef CONFIG_ARC_CACHE_VIPT_ALIASING
-
-#define clear_user_page(addr, vaddr, pg)	clear_page(addr)
-#define copy_user_page(vto, vfrom, vaddr, pg)	copy_page(vto, vfrom)
-
-#else	/* VIPT aliasing dcache */
-
 struct vm_area_struct;
 struct page;
 
@@ -35,8 +28,6 @@ void copy_user_highpage(struct page *to, struct page *from,
 			unsigned long u_vaddr, struct vm_area_struct *vma);
 void clear_user_page(void *to, unsigned long u_vaddr, struct page *page);
 
-#endif	/* CONFIG_ARC_CACHE_VIPT_ALIASING */
-
 #undef STRICT_MM_TYPECHECKS
 
 #ifdef STRICT_MM_TYPECHECKS

arch/arc/include/asm/pgtable.h

@@ -57,9 +57,9 @@
 
 #define _PAGE_ACCESSED      (1<<1)	/* Page is accessed (S) */
 #define _PAGE_CACHEABLE     (1<<2)	/* Page is cached (H) */
-#define _PAGE_EXECUTE       (1<<3)	/* Page has user execute perm (H) */
-#define _PAGE_WRITE         (1<<4)	/* Page has user write perm (H) */
-#define _PAGE_READ          (1<<5)	/* Page has user read perm (H) */
+#define _PAGE_U_EXECUTE     (1<<3)	/* Page has user execute perm (H) */
+#define _PAGE_U_WRITE       (1<<4)	/* Page has user write perm (H) */
+#define _PAGE_U_READ        (1<<5)	/* Page has user read perm (H) */
 #define _PAGE_K_EXECUTE     (1<<6)	/* Page has kernel execute perm (H) */
 #define _PAGE_K_WRITE       (1<<7)	/* Page has kernel write perm (H) */
 #define _PAGE_K_READ        (1<<8)	/* Page has kernel perm (H) */
@@ -72,9 +72,9 @@
 
 /* PD1 */
 #define _PAGE_CACHEABLE     (1<<0)	/* Page is cached (H) */
-#define _PAGE_EXECUTE       (1<<1)	/* Page has user execute perm (H) */
-#define _PAGE_WRITE         (1<<2)	/* Page has user write perm (H) */
-#define _PAGE_READ          (1<<3)	/* Page has user read perm (H) */
+#define _PAGE_U_EXECUTE     (1<<1)	/* Page has user execute perm (H) */
+#define _PAGE_U_WRITE       (1<<2)	/* Page has user write perm (H) */
+#define _PAGE_U_READ        (1<<3)	/* Page has user read perm (H) */
 #define _PAGE_K_EXECUTE     (1<<4)	/* Page has kernel execute perm (H) */
 #define _PAGE_K_WRITE       (1<<5)	/* Page has kernel write perm (H) */
 #define _PAGE_K_READ        (1<<6)	/* Page has kernel perm (H) */
@@ -93,7 +93,8 @@
 #endif
 
 /* Kernel allowed all permissions for all pages */
-#define _K_PAGE_PERMS  (_PAGE_K_EXECUTE | _PAGE_K_WRITE | _PAGE_K_READ)
+#define _K_PAGE_PERMS  (_PAGE_K_EXECUTE | _PAGE_K_WRITE | _PAGE_K_READ | \
+			_PAGE_GLOBAL | _PAGE_PRESENT)
 
 #ifdef CONFIG_ARC_CACHE_PAGES
 #define _PAGE_DEF_CACHEABLE _PAGE_CACHEABLE
@@ -106,7 +107,11 @@
  * -by default cached, unless config otherwise
  * -present in memory
  */
-#define ___DEF (_PAGE_PRESENT | _K_PAGE_PERMS | _PAGE_DEF_CACHEABLE)
+#define ___DEF (_PAGE_PRESENT | _PAGE_DEF_CACHEABLE)
+
+#define _PAGE_READ	(_PAGE_U_READ    | _PAGE_K_READ)
+#define _PAGE_WRITE	(_PAGE_U_WRITE   | _PAGE_K_WRITE)
+#define _PAGE_EXECUTE	(_PAGE_U_EXECUTE | _PAGE_K_EXECUTE)
 
 /* Set of bits not changed in pte_modify */
 #define _PAGE_CHG_MASK	(PAGE_MASK | _PAGE_ACCESSED | _PAGE_MODIFIED)
@@ -125,11 +130,10 @@
  * kernel vaddr space - visible in all addr spaces, but kernel mode only
  * Thus Global, all-kernel-access, no-user-access, cached
  */
-#define PAGE_KERNEL          __pgprot(___DEF | _PAGE_GLOBAL)
+#define PAGE_KERNEL          __pgprot(_K_PAGE_PERMS | _PAGE_DEF_CACHEABLE)
 
 /* ioremap */
-#define PAGE_KERNEL_NO_CACHE __pgprot(_PAGE_PRESENT | _K_PAGE_PERMS | \
-						     _PAGE_GLOBAL)
+#define PAGE_KERNEL_NO_CACHE __pgprot(_K_PAGE_PERMS)
 
 /**************************************************************************
  * Mapping of vm_flags (Generic VM) to PTE flags (arch specific)

arch/arc/include/asm/tlb.h

@@ -16,7 +16,7 @@
 /* Masks for actual TLB "PD"s */
 #define PTE_BITS_IN_PD0	(_PAGE_GLOBAL | _PAGE_PRESENT)
 #define PTE_BITS_IN_PD1	(PAGE_MASK | _PAGE_CACHEABLE | \
-			 _PAGE_EXECUTE | _PAGE_WRITE | _PAGE_READ | \
+			 _PAGE_U_EXECUTE | _PAGE_U_WRITE | _PAGE_U_READ | \
 			 _PAGE_K_EXECUTE | _PAGE_K_WRITE | _PAGE_K_READ)
 
 #ifndef __ASSEMBLY__

arch/arc/mm/cache_arc700.c

@@ -610,7 +610,7 @@ void __sync_icache_dcache(unsigned long paddr, unsigned long vaddr, int len)
 
 	local_irq_save(flags);
 	__ic_line_inv_vaddr(paddr, vaddr, len);
-	__dc_line_op(paddr, vaddr, len, OP_FLUSH);
+	__dc_line_op(paddr, vaddr, len, OP_FLUSH_N_INV);
 	local_irq_restore(flags);
 }
 
@@ -676,6 +676,17 @@ void flush_cache_range(struct vm_area_struct *vma, unsigned long start,
 	flush_cache_all();
 }
 
+void flush_anon_page(struct vm_area_struct *vma, struct page *page,
+		     unsigned long u_vaddr)
+{
+	/* TBD: do we really need to clear the kernel mapping */
+	__flush_dcache_page(page_address(page), u_vaddr);
+	__flush_dcache_page(page_address(page), page_address(page));
+
+}
+
+#endif
+
 void copy_user_highpage(struct page *to, struct page *from,
 	unsigned long u_vaddr, struct vm_area_struct *vma)
 {
@@ -725,16 +736,6 @@ void clear_user_page(void *to, unsigned long u_vaddr, struct page *page)
 	set_bit(PG_arch_1, &page->flags);
 }
 
-void flush_anon_page(struct vm_area_struct *vma, struct page *page,
-		     unsigned long u_vaddr)
-{
-	/* TBD: do we really need to clear the kernel mapping */
-	__flush_dcache_page(page_address(page), u_vaddr);
-	__flush_dcache_page(page_address(page), page_address(page));
-
-}
-
-#endif
 
 /**********************************************************************
  * Explicit Cache flush request from user space via syscall

arch/arc/mm/tlb.c

@@ -444,7 +444,8 @@ void update_mmu_cache(struct vm_area_struct *vma, unsigned long vaddr_unaligned,
 	 *	       so userspace sees the right data.
 	 *  (Avoids the flush for Non-exec + congruent mapping case)
 	 */
-	if (vma->vm_flags & VM_EXEC || addr_not_cache_congruent(paddr, vaddr)) {
+	if ((vma->vm_flags & VM_EXEC) ||
+	     addr_not_cache_congruent(paddr, vaddr)) {
 		struct page *page = pfn_to_page(pte_pfn(*ptep));
 
 		int dirty = test_and_clear_bit(PG_arch_1, &page->flags);

arch/arc/mm/tlbex.S

@@ -277,7 +277,7 @@ ARC_ENTRY EV_TLBMissI
 	;----------------------------------------------------------------
 	; VERIFY_PTE: Check if PTE permissions approp for executing code
 	cmp_s   r2, VMALLOC_START
-	mov.lo  r2, (_PAGE_PRESENT | _PAGE_READ | _PAGE_EXECUTE)
+	mov.lo  r2, (_PAGE_PRESENT | _PAGE_U_READ | _PAGE_U_EXECUTE)
 	mov.hs  r2, (_PAGE_PRESENT | _PAGE_K_READ | _PAGE_K_EXECUTE)
 
 	and     r3, r0, r2  ; Mask out NON Flag bits from PTE
@@ -320,9 +320,9 @@ ARC_ENTRY EV_TLBMissD
 	mov_s   r2, 0
 	lr      r3, [ecr]
 	btst_s  r3, ECR_C_BIT_DTLB_LD_MISS	; Read Access
-	or.nz   r2, r2, _PAGE_READ      	; chk for Read flag in PTE
+	or.nz   r2, r2, _PAGE_U_READ      	; chk for Read flag in PTE
 	btst_s  r3, ECR_C_BIT_DTLB_ST_MISS	; Write Access
-	or.nz   r2, r2, _PAGE_WRITE     	; chk for Write flag in PTE
+	or.nz   r2, r2, _PAGE_U_WRITE     	; chk for Write flag in PTE
 	; Above laddering takes care of XCHG access
 	;   which is both Read and Write
 

arch/arc/plat-tb10x/tb10x.c

@@ -34,31 +34,6 @@ static void __init tb10x_platform_init(void)
 	of_platform_populate(NULL, of_default_bus_match_table, NULL, NULL);
 }
 
-static void __init tb10x_platform_late_init(void)
-{
-	struct device_node *dn;
-
-	/*
-	 * Pinctrl documentation recommends setting up the iomux here for
-	 * all modules which don't require control over the pins themselves.
-	 * Modules which need this kind of assistance are compatible with
-	 * "abilis,simple-pinctrl", i.e. we can easily iterate over them.
-	 * TODO: Does this recommended method work cleanly with pins required
-	 * by modules?
-	 */
-	for_each_compatible_node(dn, NULL, "abilis,simple-pinctrl") {
-		struct platform_device *pd = of_find_device_by_node(dn);
-		struct pinctrl *pctl;
-
-		pctl = pinctrl_get_select(&pd->dev, "abilis,simple-default");
-		if (IS_ERR(pctl)) {
-			int ret = PTR_ERR(pctl);
-			dev_err(&pd->dev, "Could not set up pinctrl: %d\n",
-				ret);
-		}
-	}
-}
-
 static const char *tb10x_compat[] __initdata = {
 	"abilis,arc-tb10x",
 	NULL,
@@ -67,5 +42,4 @@ static const char *tb10x_compat[] __initdata = {
 MACHINE_START(TB10x, "tb10x")
 	.dt_compat	= tb10x_compat,
 	.init_machine	= tb10x_platform_init,
-	.init_late	= tb10x_platform_late_init,
 MACHINE_END

arch/arm/Kconfig

@@ -38,6 +38,7 @@ config ARM
 	select HAVE_GENERIC_HARDIRQS
 	select HAVE_HW_BREAKPOINT if (PERF_EVENTS && (CPU_V6 || CPU_V6K || CPU_V7))
 	select HAVE_IDE if PCI || ISA || PCMCIA
+	select HAVE_IRQ_TIME_ACCOUNTING
 	select HAVE_KERNEL_GZIP
 	select HAVE_KERNEL_LZMA
 	select HAVE_KERNEL_LZO
@@ -488,7 +489,7 @@ config ARCH_IXP4XX
 config ARCH_DOVE
 	bool "Marvell Dove"
 	select ARCH_REQUIRE_GPIOLIB
-	select CPU_V7
+	select CPU_PJ4
 	select GENERIC_CLOCKEVENTS
 	select MIGHT_HAVE_PCI
 	select PINCTRL

arch/arm/Makefile

@@ -309,7 +309,7 @@ define archhelp
   echo  '  Image         - Uncompressed kernel image (arch/$(ARCH)/boot/Image)'
   echo  '* xipImage      - XIP kernel image, if configured (arch/$(ARCH)/boot/xipImage)'
   echo  '  uImage        - U-Boot wrapped zImage'
-  echo  '  bootpImage    - Combined zImage and initial RAM disk' 
+  echo  '  bootpImage    - Combined zImage and initial RAM disk'
   echo  '                  (supply initrd image via make variable INITRD=<path>)'
   echo  '* dtbs          - Build device tree blobs for enabled boards'
   echo  '  install       - Install uncompressed kernel'

arch/arm/boot/dts/Makefile

@@ -177,7 +177,9 @@ dtb-$(CONFIG_ARCH_SPEAR3XX)+= spear300-evb.dtb \
 	spear320-evb.dtb \
 	spear320-hmi.dtb
 dtb-$(CONFIG_ARCH_SPEAR6XX)+= spear600-evb.dtb
-dtb-$(CONFIG_ARCH_SUNXI) += sun4i-a10-cubieboard.dtb \
+dtb-$(CONFIG_ARCH_SUNXI) += \
+	sun4i-a10-cubieboard.dtb \
+	sun4i-a10-mini-xplus.dtb \
 	sun4i-a10-hackberry.dtb \
 	sun5i-a13-olinuxino.dtb
 dtb-$(CONFIG_ARCH_TEGRA) += tegra20-harmony.dtb \

arch/arm/boot/dts/armada-370-xp.dtsi

@@ -33,7 +33,8 @@
 		#size-cells = <1>;
 		compatible = "simple-bus";
 		interrupt-parent = <&mpic>;
-		ranges = <0 0 0xd0000000 0x100000>;
+		ranges = <0          0 0xd0000000 0x0100000 /* internal registers */
+			  0xe0000000 0 0xe0000000 0x8100000 /* PCIe */>;
 
 		internal-regs {
 			compatible = "simple-bus";

arch/arm/boot/dts/armada-370.dtsi

@@ -29,7 +29,8 @@
 	};
 
 	soc {
-		ranges = <0 0xd0000000 0x100000>;
+		ranges = <0          0xd0000000 0x0100000 /* internal registers */
+			  0xe0000000 0xe0000000 0x8100000 /* PCIe */>;
 		internal-regs {
 			system-controller@18200 {
 				compatible = "marvell,armada-370-xp-system-controller";
@@ -38,12 +39,12 @@
 
 			L2: l2-cache {
 				compatible = "marvell,aurora-outer-cache";
-				reg = <0xd0008000 0x1000>;
+				reg = <0x08000 0x1000>;
 				cache-id-part = <0x100>;
 				wt-override;
 			};
 
-			mpic: interrupt-controller@20000 {
+			interrupt-controller@20000 {
 				reg = <0x20a00 0x1d0>, <0x21870 0x58>;
 			};
 

arch/arm/boot/dts/armada-xp-gp.dts

@@ -39,6 +39,9 @@
 	};
 
 	soc {
+		ranges = <0          0 0xd0000000 0x100000
+			  0xf0000000 0 0xf0000000 0x1000000>;
+
 		internal-regs {
 			serial@12000 {
 				clock-frequency = <250000000>;

arch/arm/boot/dts/armada-xp-openblocks-ax3-4.dts

@@ -27,6 +27,9 @@
 	};
 
 	soc {
+		ranges = <0          0 0xd0000000 0x100000
+			  0xf0000000 0 0xf0000000 0x8000000>;
+
 		internal-regs {
 			serial@12000 {
 				clock-frequency = <250000000>;

arch/arm/boot/dts/armada-xp.dtsi

@@ -31,7 +31,7 @@
 				wt-override;
 			};
 
-			mpic: interrupt-controller@20000 {
+			interrupt-controller@20000 {
 			      reg = <0x20a00 0x2d0>, <0x21070 0x58>;
 			};
 

arch/arm/boot/dts/at91sam9260.dtsi

@@ -264,7 +264,7 @@
 						atmel,pins =
 							<0 10 0x2 0x0	/* PA10 periph B */
 							 0 11 0x2 0x0	/* PA11 periph B */
-							 0 24 0x2 0x0	/* PA24 periph B */
+							 0 22 0x2 0x0	/* PA22 periph B */
 							 0 25 0x2 0x0	/* PA25 periph B */
 							 0 26 0x2 0x0	/* PA26 periph B */
 							 0 27 0x2 0x0	/* PA27 periph B */

arch/arm/boot/dts/at91sam9n12.dtsi

@@ -57,6 +57,7 @@
 				compatible = "atmel,at91rm9200-aic";
 				interrupt-controller;
 				reg = <0xfffff000 0x200>;
+				atmel,external-irqs = <31>;
 			};
 
 			ramc0: ramc@ffffe800 {

arch/arm/boot/dts/at91sam9x25ek.dts

@@ -11,7 +11,7 @@
 /include/ "at91sam9x5ek.dtsi"
 
 / {
-	model = "Atmel AT91SAM9G25-EK";
+	model = "Atmel AT91SAM9X25-EK";
 	compatible = "atmel,at91sam9x25ek", "atmel,at91sam9x5ek", "atmel,at91sam9x5", "atmel,at91sam9";
 
 	ahb {

arch/arm/boot/dts/omap3.dtsi

@@ -516,7 +516,7 @@
 		usb_otg_hs: usb_otg_hs@480ab000 {
 			compatible = "ti,omap3-musb";
 			reg = <0x480ab000 0x1000>;
-			interrupts = <0 92 0x4>, <0 93 0x4>;
+			interrupts = <92>, <93>;
 			interrupt-names = "mc", "dma";
 			ti,hwmods = "usb_otg_hs";
 			multipoint = <1>;

arch/arm/boot/dts/sama5d3.dtsi

@@ -75,11 +75,6 @@
 				compatible = "atmel,at91sam9x5-spi";
 				reg = <0xf0004000 0x100>;
 				interrupts = <24 4 3>;
-				cs-gpios = <&pioD 13 0
-					    &pioD 14 0 /* conflicts with SCK0 and CANRX0 */
-					    &pioD 15 0 /* conflicts with CTS0 and CANTX0 */
-					    &pioD 16 0 /* conflicts with RTS0 and PWMFI3 */
-					   >;
 				pinctrl-names = "default";
 				pinctrl-0 = <&pinctrl_spi0>;
 				status = "disabled";
@@ -156,7 +151,7 @@
 			};
 
 			macb0: ethernet@f0028000 {
-				compatible = "cnds,pc302-gem", "cdns,gem";
+				compatible = "cdns,pc302-gem", "cdns,gem";
 				reg = <0xf0028000 0x100>;
 				interrupts = <34 4 3>;
 				pinctrl-names = "default";
@@ -203,11 +198,6 @@
 				compatible = "atmel,at91sam9x5-spi";
 				reg = <0xf8008000 0x100>;
 				interrupts = <25 4 3>;
-				cs-gpios = <&pioC 25 0
-					    &pioC 26 0 /* conflitcs with TWD1 and ISI_D11 */
-					    &pioC 27 0 /* conflitcs with TWCK1 and ISI_D10 */
-					    &pioC 28 0 /* conflitcs with PWMFI0 and ISI_D9 */
-					   >;
 				pinctrl-names = "default";
 				pinctrl-0 = <&pinctrl_spi1>;
 				status = "disabled";

arch/arm/boot/dts/sama5d3xcm.dtsi

@@ -32,6 +32,10 @@
 
 	ahb {
 		apb {
+			spi0: spi@f0004000 {
+				cs-gpios = <&pioD 13 0>, <0>, <0>, <0>;
+			};
+
 			macb0: ethernet@f0028000 {
 				phy-mode = "rgmii";
 			};

arch/arm/boot/dts/ste-nomadik-s8815.dts

@@ -14,13 +14,19 @@
 		bootargs = "root=/dev/ram0 console=ttyAMA1,115200n8 earlyprintk";
 	};
 
+	/* This is where the interrupt is routed on the S8815 board */
+	external-bus@34000000 {
+		ethernet@300 {
+			interrupt-parent = <&gpio3>;
+			interrupts = <8 0x1>;
+		};
+	};
+
 	/* Custom board node with GPIO pins to active etc */
 	usb-s8815 {
 		/* The S8815 is using this very GPIO pin for the SMSC91x IRQs */
 		ethernet-gpio {
-			gpios = <&gpio3 19 0x1>;
-			interrupts = <19 0x1>;
-			interrupt-parent = <&gpio3>;
+			gpios = <&gpio3 8 0x1>;
 		};
 		/* This will bias the MMC/SD card detect line */
 		mmcsd-gpio {

arch/arm/boot/dts/sun4i-a10-mini-xplus.dts

@@ -22,8 +22,8 @@
 		bootargs = "earlyprintk console=ttyS0,115200";
 	};
 
-	soc {
-		uart0: uart@01c28000 {
+	soc@01c20000 {
+		uart0: serial@01c28000 {
 			pinctrl-names = "default";
 			pinctrl-0 = <&uart0_pins_a>;
 			status = "okay";

arch/arm/common/mcpm_platsmp.c

@@ -15,8 +15,6 @@
 #include <linux/smp.h>
 #include <linux/spinlock.h>
 
-#include <linux/irqchip/arm-gic.h>
-
 #include <asm/mcpm.h>
 #include <asm/smp.h>
 #include <asm/smp_plat.h>
@@ -49,7 +47,6 @@ static int __cpuinit mcpm_boot_secondary(unsigned int cpu, struct task_struct *i
 static void __cpuinit mcpm_secondary_init(unsigned int cpu)
 {
 	mcpm_cpu_powered_up();
-	gic_secondary_init(0);
 }
 
 #ifdef CONFIG_HOTPLUG_CPU

arch/arm/configs/omap1_defconfig

@@ -199,7 +199,6 @@ CONFIG_USB_PHY=y
 CONFIG_USB_DEBUG=y
 CONFIG_USB_DEVICEFS=y
 # CONFIG_USB_DEVICE_CLASS is not set
-CONFIG_USB_SUSPEND=y
 CONFIG_USB_MON=y
 CONFIG_USB_OHCI_HCD=y
 CONFIG_USB_STORAGE=y

arch/arm/configs/omap2plus_defconfig

@@ -20,6 +20,7 @@ CONFIG_MODULE_FORCE_UNLOAD=y
 CONFIG_MODVERSIONS=y
 CONFIG_MODULE_SRCVERSION_ALL=y
 # CONFIG_BLK_DEV_BSG is not set
+CONFIG_ARCH_MULTI_V6=y
 CONFIG_ARCH_OMAP2PLUS=y
 CONFIG_OMAP_RESET_CLOCKS=y
 CONFIG_OMAP_MUX_DEBUG=y
@@ -204,7 +205,6 @@ CONFIG_USB=y
 CONFIG_USB_DEBUG=y
 CONFIG_USB_ANNOUNCE_NEW_DEVICES=y
 CONFIG_USB_DEVICEFS=y
-CONFIG_USB_SUSPEND=y
 CONFIG_USB_MON=y
 CONFIG_USB_WDM=y
 CONFIG_USB_STORAGE=y

arch/arm/configs/tegra_defconfig

@@ -153,6 +153,7 @@ CONFIG_MEDIA_CAMERA_SUPPORT=y
 CONFIG_MEDIA_USB_SUPPORT=y
 CONFIG_USB_VIDEO_CLASS=m
 CONFIG_DRM=y
+CONFIG_TEGRA_HOST1X=y
 CONFIG_DRM_TEGRA=y
 CONFIG_BACKLIGHT_LCD_SUPPORT=y
 # CONFIG_LCD_CLASS_DEVICE is not set
@@ -202,7 +203,7 @@ CONFIG_TEGRA20_APB_DMA=y
 CONFIG_STAGING=y
 CONFIG_SENSORS_ISL29018=y
 CONFIG_SENSORS_ISL29028=y
-CONFIG_SENSORS_AK8975=y
+CONFIG_AK8975=y
 CONFIG_MFD_NVEC=y
 CONFIG_KEYBOARD_NVEC=y
 CONFIG_SERIO_NVEC_PS2=y

arch/arm/crypto/sha1-armv4-large.S

@@ -195,6 +195,7 @@ ENTRY(sha1_block_data_order)
 	add	r3,r3,r10			@ E+=F_00_19(B,C,D)
 	cmp	r14,sp
 	bne	.L_00_15		@ [((11+4)*5+2)*3]
+	sub	sp,sp,#25*4
 #if __ARM_ARCH__<7
 	ldrb	r10,[r1,#2]
 	ldrb	r9,[r1,#3]
@@ -290,7 +291,6 @@ ENTRY(sha1_block_data_order)
 	add	r3,r3,r10			@ E+=F_00_19(B,C,D)
 
 	ldr	r8,.LK_20_39		@ [+15+16*4]
-	sub	sp,sp,#25*4
 	cmn	sp,#0			@ [+3], clear carry to denote 20_39
 .L_20_39_or_60_79:
 	ldr	r9,[r14,#15*4]

arch/arm/include/asm/cmpxchg.h

@@ -233,15 +233,15 @@ static inline unsigned long __cmpxchg_local(volatile void *ptr,
 	((__typeof__(*(ptr)))atomic64_cmpxchg(container_of((ptr),	\
 						atomic64_t,		\
 						counter),		\
-					      (unsigned long)(o),	\
-					      (unsigned long)(n)))
+					      (unsigned long long)(o),	\
+					      (unsigned long long)(n)))
 
 #define cmpxchg64_local(ptr, o, n)					\
 	((__typeof__(*(ptr)))local64_cmpxchg(container_of((ptr),	\
 						local64_t,		\
 						a),			\
-					     (unsigned long)(o),	\
-					     (unsigned long)(n)))
+					     (unsigned long long)(o),	\
+					     (unsigned long long)(n)))
 
 #endif	/* __LINUX_ARM_ARCH__ >= 6 */
 

arch/arm/include/debug/ux500.S

@@ -24,9 +24,9 @@
 #define U8500_UART0_PHYS_BASE	(0x80120000)
 #define U8500_UART1_PHYS_BASE	(0x80121000)
 #define U8500_UART2_PHYS_BASE	(0x80007000)
-#define U8500_UART0_VIRT_BASE	(0xa8120000)
-#define U8500_UART1_VIRT_BASE	(0xa8121000)
-#define U8500_UART2_VIRT_BASE	(0xa8007000)
+#define U8500_UART0_VIRT_BASE	(0xf8120000)
+#define U8500_UART1_VIRT_BASE	(0xf8121000)
+#define U8500_UART2_VIRT_BASE	(0xf8007000)
 #define __UX500_PHYS_UART(n)	U8500_UART##n##_PHYS_BASE
 #define __UX500_VIRT_UART(n)	U8500_UART##n##_VIRT_BASE
 #endif

arch/arm/kernel/process.c

@@ -411,7 +411,6 @@ static struct vm_area_struct gate_vma = {
 	.vm_start	= 0xffff0000,
 	.vm_end		= 0xffff0000 + PAGE_SIZE,
 	.vm_flags	= VM_READ | VM_EXEC | VM_MAYREAD | VM_MAYEXEC,
-	.vm_mm		= &init_mm,
 };
 
 static int __init gate_vma_init(void)

arch/arm/kernel/smp.c

@@ -251,7 +251,7 @@ void __ref cpu_die(void)
 	 * this returns, power and/or clocks can be removed at any point
 	 * from this CPU and its cache by platform_cpu_kill().
 	 */
-	RCU_NONIDLE(complete(&cpu_died));
+	complete(&cpu_died);
 
 	/*
 	 * Ensure that the cache lines associated with that completion are

arch/arm/mach-at91/at91rm9200_time.c

@@ -174,6 +174,7 @@ clkevt32k_next_event(unsigned long delta, struct clock_event_device *dev)
 static struct clock_event_device clkevt = {
 	.name		= "at91_tick",
 	.features	= CLOCK_EVT_FEAT_PERIODIC | CLOCK_EVT_FEAT_ONESHOT,
+	.shift		= 32,
 	.rating		= 150,
 	.set_next_event	= clkevt32k_next_event,
 	.set_mode	= clkevt32k_mode,
@@ -264,9 +265,11 @@ void __init at91rm9200_timer_init(void)
 	at91_st_write(AT91_ST_RTMR, 1);
 
 	/* Setup timer clockevent, with minimum of two ticks (important!!) */
+	clkevt.mult = div_sc(AT91_SLOW_CLOCK, NSEC_PER_SEC, clkevt.shift);
+	clkevt.max_delta_ns = clockevent_delta2ns(AT91_ST_ALMV, &clkevt);
+	clkevt.min_delta_ns = clockevent_delta2ns(2, &clkevt) + 1;
 	clkevt.cpumask = cpumask_of(0);
-	clockevents_config_and_register(&clkevt, AT91_SLOW_CLOCK,
-					2, AT91_ST_ALMV);
+	clockevents_register_device(&clkevt);
 
 	/* register clocksource */
 	clocksource_register_hz(&clk32k, AT91_SLOW_CLOCK);

arch/arm/mach-at91/at91sam9n12.c

@@ -223,13 +223,7 @@ static void __init at91sam9n12_map_io(void)
 	at91_init_sram(0, AT91SAM9N12_SRAM_BASE, AT91SAM9N12_SRAM_SIZE);
 }
 
-void __init at91sam9n12_initialize(void)
-{
-	at91_extern_irq = (1 << AT91SAM9N12_ID_IRQ0);
-}
-
 AT91_SOC_START(at91sam9n12)
 	.map_io = at91sam9n12_map_io,
 	.register_clocks = at91sam9n12_register_clocks,
-	.init = at91sam9n12_initialize,
 AT91_SOC_END

arch/arm/mach-at91/include/mach/at91_pmc.h

@@ -179,9 +179,9 @@ extern void __iomem *at91_pmc_base;
 #define		AT91_PMC_PCR_CMD	(0x1  <<  12)		/* Command (read=0, write=1) */
 #define		AT91_PMC_PCR_DIV(n)	((n)  <<  16)		/* Divisor Value */
 #define			AT91_PMC_PCR_DIV0	0x0			/* Peripheral clock is MCK */
-#define			AT91_PMC_PCR_DIV2	0x2			/* Peripheral clock is MCK/2 */
-#define			AT91_PMC_PCR_DIV4	0x4			/* Peripheral clock is MCK/4 */
-#define			AT91_PMC_PCR_DIV8	0x8			/* Peripheral clock is MCK/8 */
+#define			AT91_PMC_PCR_DIV2	0x1			/* Peripheral clock is MCK/2 */
+#define			AT91_PMC_PCR_DIV4	0x2			/* Peripheral clock is MCK/4 */
+#define			AT91_PMC_PCR_DIV8	0x3			/* Peripheral clock is MCK/8 */
 #define		AT91_PMC_PCR_EN		(0x1  <<  28)		/* Enable */
 
 #endif

arch/arm/mach-imx/clk-imx6q.c

@@ -177,7 +177,8 @@ int imx6q_set_lpm(enum mxc_cpu_pwr_mode mode)
 static const char *step_sels[]	= { "osc", "pll2_pfd2_396m", };
 static const char *pll1_sw_sels[]	= { "pll1_sys", "step", };
 static const char *periph_pre_sels[]	= { "pll2_bus", "pll2_pfd2_396m", "pll2_pfd0_352m", "pll2_198m", };
-static const char *periph_clk2_sels[]	= { "pll3_usb_otg", "osc", };
+static const char *periph_clk2_sels[]	= { "pll3_usb_otg", "osc", "osc", "dummy", };
+static const char *periph2_clk2_sels[]	= { "pll3_usb_otg", "pll2_bus", };
 static const char *periph_sels[]	= { "periph_pre", "periph_clk2", };
 static const char *periph2_sels[]	= { "periph2_pre", "periph2_clk2", };
 static const char *axi_sels[]		= { "periph", "pll2_pfd2_396m", "pll3_pfd1_540m", };
@@ -185,7 +186,7 @@ static const char *audio_sels[]	= { "pll4_post_div", "pll3_pfd2_508m", "pll3_pfd
 static const char *gpu_axi_sels[]	= { "axi", "ahb", };
 static const char *gpu2d_core_sels[]	= { "axi", "pll3_usb_otg", "pll2_pfd0_352m", "pll2_pfd2_396m", };
 static const char *gpu3d_core_sels[]	= { "mmdc_ch0_axi", "pll3_usb_otg", "pll2_pfd1_594m", "pll2_pfd2_396m", };
-static const char *gpu3d_shader_sels[] = { "mmdc_ch0_axi", "pll3_usb_otg", "pll2_pfd1_594m", "pll2_pfd9_720m", };
+static const char *gpu3d_shader_sels[] = { "mmdc_ch0_axi", "pll3_usb_otg", "pll2_pfd1_594m", "pll3_pfd0_720m", };
 static const char *ipu_sels[]		= { "mmdc_ch0_axi", "pll2_pfd2_396m", "pll3_120m", "pll3_pfd1_540m", };
 static const char *ldb_di_sels[]	= { "pll5_video", "pll2_pfd0_352m", "pll2_pfd2_396m", "mmdc_ch1_axi", "pll3_usb_otg", };
 static const char *ipu_di_pre_sels[]	= { "mmdc_ch0_axi", "pll3_usb_otg", "pll5_video_div", "pll2_pfd0_352m", "pll2_pfd2_396m", "pll3_pfd1_540m", };
@@ -369,8 +370,8 @@ int __init mx6q_clocks_init(void)
 	clk[pll1_sw]          = imx_clk_mux("pll1_sw",	        base + 0xc,  2,  1, pll1_sw_sels,      ARRAY_SIZE(pll1_sw_sels));
 	clk[periph_pre]       = imx_clk_mux("periph_pre",       base + 0x18, 18, 2, periph_pre_sels,   ARRAY_SIZE(periph_pre_sels));
 	clk[periph2_pre]      = imx_clk_mux("periph2_pre",      base + 0x18, 21, 2, periph_pre_sels,   ARRAY_SIZE(periph_pre_sels));
-	clk[periph_clk2_sel]  = imx_clk_mux("periph_clk2_sel",  base + 0x18, 12, 1, periph_clk2_sels,  ARRAY_SIZE(periph_clk2_sels));
-	clk[periph2_clk2_sel] = imx_clk_mux("periph2_clk2_sel", base + 0x18, 20, 1, periph_clk2_sels,  ARRAY_SIZE(periph_clk2_sels));
+	clk[periph_clk2_sel]  = imx_clk_mux("periph_clk2_sel",  base + 0x18, 12, 2, periph_clk2_sels,  ARRAY_SIZE(periph_clk2_sels));
+	clk[periph2_clk2_sel] = imx_clk_mux("periph2_clk2_sel", base + 0x18, 20, 1, periph2_clk2_sels, ARRAY_SIZE(periph2_clk2_sels));
 	clk[axi_sel]          = imx_clk_mux("axi_sel",          base + 0x14, 6,  2, axi_sels,          ARRAY_SIZE(axi_sels));
 	clk[esai_sel]         = imx_clk_mux("esai_sel",         base + 0x20, 19, 2, audio_sels,        ARRAY_SIZE(audio_sels));
 	clk[asrc_sel]         = imx_clk_mux("asrc_sel",         base + 0x30, 7,  2, audio_sels,        ARRAY_SIZE(audio_sels));
@@ -498,7 +499,7 @@ int __init mx6q_clocks_init(void)
 	clk[ldb_di1]      = imx_clk_gate2("ldb_di1",       "ldb_di1_podf",      base + 0x74, 14);
 	clk[ipu2_di1]     = imx_clk_gate2("ipu2_di1",      "ipu2_di1_sel",      base + 0x74, 10);
 	clk[hsi_tx]       = imx_clk_gate2("hsi_tx",        "hsi_tx_podf",       base + 0x74, 16);
-	clk[mlb]          = imx_clk_gate2("mlb",           "pll8_mlb",          base + 0x74, 18);
+	clk[mlb]          = imx_clk_gate2("mlb",           "axi",               base + 0x74, 18);
 	clk[mmdc_ch0_axi] = imx_clk_gate2("mmdc_ch0_axi",  "mmdc_ch0_axi_podf", base + 0x74, 20);
 	clk[mmdc_ch1_axi] = imx_clk_gate2("mmdc_ch1_axi",  "mmdc_ch1_axi_podf", base + 0x74, 22);
 	clk[ocram]        = imx_clk_gate2("ocram",         "ahb",               base + 0x74, 28);

arch/arm/mach-imx/headsmp.S

@@ -18,8 +18,20 @@
 	.section ".text.head", "ax"
 
 #ifdef CONFIG_SMP
+diag_reg_offset:
+	.word	g_diag_reg - .
+
+	.macro	set_diag_reg
+	adr	r0, diag_reg_offset
+	ldr	r1, [r0]
+	add	r1, r1, r0		@ r1 = physical &g_diag_reg
+	ldr	r0, [r1]
+	mcr	p15, 0, r0, c15, c0, 1	@ write diagnostic register
+	.endm
+
 ENTRY(v7_secondary_startup)
 	bl	v7_invalidate_l1
+	set_diag_reg
 	b	secondary_startup
 ENDPROC(v7_secondary_startup)
 #endif

arch/arm/mach-imx/platsmp.c

@@ -12,6 +12,7 @@
 
 #include <linux/init.h>
 #include <linux/smp.h>
+#include <asm/cacheflush.h>
 #include <asm/page.h>
 #include <asm/smp_scu.h>
 #include <asm/mach/map.h>
@@ -21,6 +22,7 @@
 
 #define SCU_STANDBY_ENABLE	(1 << 5)
 
+u32 g_diag_reg;
 static void __iomem *scu_base;
 
 static struct map_desc scu_io_desc __initdata = {
@@ -80,6 +82,18 @@ void imx_smp_prepare(void)
 static void __init imx_smp_prepare_cpus(unsigned int max_cpus)
 {
 	imx_smp_prepare();
+
+	/*
+	 * The diagnostic register holds the errata bits.  Mostly bootloader
+	 * does not bring up secondary cores, so that when errata bits are set
+	 * in bootloader, they are set only for boot cpu.  But on a SMP
+	 * configuration, it should be equally done on every single core.
+	 * Read the register from boot cpu here, and will replicate it into
+	 * secondary cores when booting them.
+	 */
+	asm("mrc p15, 0, %0, c15, c0, 1" : "=r" (g_diag_reg) : : "cc");
+	__cpuc_flush_dcache_area(&g_diag_reg, sizeof(g_diag_reg));
+	outer_clean_range(__pa(&g_diag_reg), __pa(&g_diag_reg + 1));
 }
 
 struct smp_operations  imx_smp_ops __initdata = {

arch/arm/mach-kirkwood/common.c

@@ -528,12 +528,6 @@ void __init kirkwood_init_early(void)
 {
 	orion_time_set_base(TIMER_VIRT_BASE);
 
-	/*
-	 * Some Kirkwood devices allocate their coherent buffers from atomic
-	 * context. Increase size of atomic coherent pool to make sure such
-	 * the allocations won't fail.
-	 */
-	init_dma_coherent_pool_size(SZ_1M);
 	mvebu_mbus_init("marvell,kirkwood-mbus",
 			BRIDGE_WINS_BASE, BRIDGE_WINS_SZ,
 			DDR_WINDOW_CPU_BASE, DDR_WINDOW_CPU_SZ);

arch/arm/mach-kirkwood/ts219-setup.c

@@ -124,7 +124,7 @@ static void __init qnap_ts219_init(void)
 static int __init ts219_pci_init(void)
 {
 	if (machine_is_ts219())
-		kirkwood_pcie_init(KW_PCIE0);
+		kirkwood_pcie_init(KW_PCIE1 | KW_PCIE0);
 
 	return 0;
 }

arch/arm/mach-mvebu/Kconfig

@@ -15,6 +15,7 @@ config ARCH_MVEBU
 	select MVEBU_CLK_GATING
 	select MVEBU_MBUS
 	select ZONE_DMA if ARM_LPAE
+	select ARCH_REQUIRE_GPIOLIB
 
 if ARCH_MVEBU
 

arch/arm/mach-mvebu/armada-370-xp.c

@@ -53,13 +53,6 @@ void __init armada_370_xp_init_early(void)
 {
 	char *mbus_soc_name;
 
-	/*
-	 * Some Armada 370/XP devices allocate their coherent buffers
-	 * from atomic context. Increase size of atomic coherent pool
-	 * to make sure such the allocations won't fail.
-	 */
-	init_dma_coherent_pool_size(SZ_1M);
-
 	/*
 	 * This initialization will be replaced by a DT-based
 	 * initialization once the mvebu-mbus driver gains DT support.

arch/arm/mach-omap1/dma.c

@@ -345,6 +345,7 @@ static int __init omap1_system_dma_init(void)
 		dev_err(&pdev->dev,
 			"%s: Memory allocation failed for d->chan!\n",
 			__func__);
+		ret = -ENOMEM;
 		goto exit_release_d;
 	}
 

arch/arm/mach-omap2/cclock33xx_data.c

@@ -454,9 +454,29 @@ DEFINE_CLK_GATE(cefuse_fck, "sys_clkin_ck", &sys_clkin_ck, 0x0,
  */
 DEFINE_CLK_FIXED_FACTOR(clkdiv32k_ck, "clk_24mhz", &clk_24mhz, 0x0, 1, 732);
 
-DEFINE_CLK_GATE(clkdiv32k_ick, "clkdiv32k_ck", &clkdiv32k_ck, 0x0,
-		AM33XX_CM_PER_CLKDIV32K_CLKCTRL, AM33XX_MODULEMODE_SWCTRL_SHIFT,
-		0x0, NULL);
+static struct clk clkdiv32k_ick;
+
+static const char *clkdiv32k_ick_parent_names[] = {
+	"clkdiv32k_ck",
+};
+
+static const struct clk_ops clkdiv32k_ick_ops = {
+	.enable         = &omap2_dflt_clk_enable,
+	.disable        = &omap2_dflt_clk_disable,
+	.is_enabled     = &omap2_dflt_clk_is_enabled,
+	.init           = &omap2_init_clk_clkdm,
+};
+
+static struct clk_hw_omap clkdiv32k_ick_hw = {
+	.hw	= {
+		.clk	= &clkdiv32k_ick,
+	},
+	.enable_reg	= AM33XX_CM_PER_CLKDIV32K_CLKCTRL,
+	.enable_bit	= AM33XX_MODULEMODE_SWCTRL_SHIFT,
+	.clkdm_name	= "clk_24mhz_clkdm",
+};
+
+DEFINE_STRUCT_CLK(clkdiv32k_ick, clkdiv32k_ick_parent_names, clkdiv32k_ick_ops);
 
 /* "usbotg_fck" is an additional clock and not really a modulemode */
 DEFINE_CLK_GATE(usbotg_fck, "dpll_per_ck", &dpll_per_ck, 0x0,

arch/arm/mach-omap2/omap_hwmod.c

@@ -1356,13 +1356,27 @@ static void _enable_sysc(struct omap_hwmod *oh)
 
 	clkdm = _get_clkdm(oh);
 	if (sf & SYSC_HAS_SIDLEMODE) {
+		if (oh->flags & HWMOD_SWSUP_SIDLE ||
+		    oh->flags & HWMOD_SWSUP_SIDLE_ACT) {
+			idlemode = HWMOD_IDLEMODE_NO;
+		} else {
+			if (sf & SYSC_HAS_ENAWAKEUP)
+				_enable_wakeup(oh, &v);
+			if (oh->class->sysc->idlemodes & SIDLE_SMART_WKUP)
+				idlemode = HWMOD_IDLEMODE_SMART_WKUP;
+			else
+				idlemode = HWMOD_IDLEMODE_SMART;
+		}
+
+		/*
+		 * This is special handling for some IPs like
+		 * 32k sync timer. Force them to idle!
+		 */
 		clkdm_act = (clkdm && clkdm->flags & CLKDM_ACTIVE_WITH_MPU);
 		if (clkdm_act && !(oh->class->sysc->idlemodes &
 				   (SIDLE_SMART | SIDLE_SMART_WKUP)))
 			idlemode = HWMOD_IDLEMODE_FORCE;
-		else
-			idlemode = (oh->flags & HWMOD_SWSUP_SIDLE) ?
-				HWMOD_IDLEMODE_NO : HWMOD_IDLEMODE_SMART;
+
 		_set_slave_idlemode(oh, idlemode, &v);
 	}
 
@@ -1391,10 +1405,6 @@ static void _enable_sysc(struct omap_hwmod *oh)
 	    (sf & SYSC_HAS_CLOCKACTIVITY))
 		_set_clockactivity(oh, oh->class->sysc->clockact, &v);
 
-	/* If slave is in SMARTIDLE, also enable wakeup */
-	if ((sf & SYSC_HAS_SIDLEMODE) && !(oh->flags & HWMOD_SWSUP_SIDLE))
-		_enable_wakeup(oh, &v);
-
 	_write_sysconfig(v, oh);
 
 	/*
@@ -1430,13 +1440,16 @@ static void _idle_sysc(struct omap_hwmod *oh)
 	sf = oh->class->sysc->sysc_flags;
 
 	if (sf & SYSC_HAS_SIDLEMODE) {
-		/* XXX What about HWMOD_IDLEMODE_SMART_WKUP? */
-		if (oh->flags & HWMOD_SWSUP_SIDLE ||
-		    !(oh->class->sysc->idlemodes &
-		      (SIDLE_SMART | SIDLE_SMART_WKUP)))
+		if (oh->flags & HWMOD_SWSUP_SIDLE) {
 			idlemode = HWMOD_IDLEMODE_FORCE;
-		else
-			idlemode = HWMOD_IDLEMODE_SMART;
+		} else {
+			if (sf & SYSC_HAS_ENAWAKEUP)
+				_enable_wakeup(oh, &v);
+			if (oh->class->sysc->idlemodes & SIDLE_SMART_WKUP)
+				idlemode = HWMOD_IDLEMODE_SMART_WKUP;
+			else
+				idlemode = HWMOD_IDLEMODE_SMART;
+		}
 		_set_slave_idlemode(oh, idlemode, &v);
 	}
 
@@ -1455,10 +1468,6 @@ static void _idle_sysc(struct omap_hwmod *oh)
 		_set_master_standbymode(oh, idlemode, &v);
 	}
 
-	/* If slave is in SMARTIDLE, also enable wakeup */
-	if ((sf & SYSC_HAS_SIDLEMODE) && !(oh->flags & HWMOD_SWSUP_SIDLE))
-		_enable_wakeup(oh, &v);
-
 	_write_sysconfig(v, oh);
 }
 
@@ -2065,7 +2074,7 @@ static int _omap4_get_context_lost(struct omap_hwmod *oh)
  * do so is present in the hwmod data, then call it and pass along the
  * return value; otherwise, return 0.
  */
-static int __init _enable_preprogram(struct omap_hwmod *oh)
+static int _enable_preprogram(struct omap_hwmod *oh)
 {
 	if (!oh->class->enable_preprogram)
 		return 0;
@@ -2245,42 +2254,6 @@ static int _idle(struct omap_hwmod *oh)
 	return 0;
 }
 
-/**
- * omap_hwmod_set_ocp_autoidle - set the hwmod's OCP autoidle bit
- * @oh: struct omap_hwmod *
- * @autoidle: desired AUTOIDLE bitfield value (0 or 1)
- *
- * Sets the IP block's OCP autoidle bit in hardware, and updates our
- * local copy. Intended to be used by drivers that require
- * direct manipulation of the AUTOIDLE bits.
- * Returns -EINVAL if @oh is null or is not in the ENABLED state, or passes
- * along the return value from _set_module_autoidle().
- *
- * Any users of this function should be scrutinized carefully.
- */
-int omap_hwmod_set_ocp_autoidle(struct omap_hwmod *oh, u8 autoidle)
-{
-	u32 v;
-	int retval = 0;
-	unsigned long flags;
-
-	if (!oh || oh->_state != _HWMOD_STATE_ENABLED)
-		return -EINVAL;
-
-	spin_lock_irqsave(&oh->_lock, flags);
-
-	v = oh->_sysc_cache;
-
-	retval = _set_module_autoidle(oh, autoidle, &v);
-
-	if (!retval)
-		_write_sysconfig(v, oh);
-
-	spin_unlock_irqrestore(&oh->_lock, flags);
-
-	return retval;
-}
-
 /**
  * _shutdown - shutdown an omap_hwmod
  * @oh: struct omap_hwmod *
@@ -3179,38 +3152,6 @@ error:
 	return ret;
 }
 
-/**
- * omap_hwmod_set_slave_idlemode - set the hwmod's OCP slave idlemode
- * @oh: struct omap_hwmod *
- * @idlemode: SIDLEMODE field bits (shifted to bit 0)
- *
- * Sets the IP block's OCP slave idlemode in hardware, and updates our
- * local copy.  Intended to be used by drivers that have some erratum
- * that requires direct manipulation of the SIDLEMODE bits.  Returns
- * -EINVAL if @oh is null, or passes along the return value from
- * _set_slave_idlemode().
- *
- * XXX Does this function have any current users?  If not, we should
- * remove it; it is better to let the rest of the hwmod code handle this.
- * Any users of this function should be scrutinized carefully.
- */
-int omap_hwmod_set_slave_idlemode(struct omap_hwmod *oh, u8 idlemode)
-{
-	u32 v;
-	int retval = 0;
-
-	if (!oh)
-		return -EINVAL;
-
-	v = oh->_sysc_cache;
-
-	retval = _set_slave_idlemode(oh, idlemode, &v);
-	if (!retval)
-		_write_sysconfig(v, oh);
-
-	return retval;
-}
-
 /**
  * omap_hwmod_lookup - look up a registered omap_hwmod by name
  * @name: name of the omap_hwmod to look up

arch/arm/mach-omap2/omap_hwmod.h

@@ -463,6 +463,9 @@ struct omap_hwmod_omap4_prcm {
  *     is kept in force-standby mode. Failing to do so causes PM problems
  *     with musb on OMAP3630 at least. Note that musb has a dedicated register
  *     to control MSTANDBY signal when MIDLEMODE is set to force-standby.
+ * HWMOD_SWSUP_SIDLE_ACT: omap_hwmod code should manually bring the module
+ *     out of idle, but rely on smart-idle to the put it back in idle,
+ *     so the wakeups are still functional (Only known case for now is UART)
  */
 #define HWMOD_SWSUP_SIDLE			(1 << 0)
 #define HWMOD_SWSUP_MSTANDBY			(1 << 1)
@@ -476,6 +479,7 @@ struct omap_hwmod_omap4_prcm {
 #define HWMOD_EXT_OPT_MAIN_CLK			(1 << 9)
 #define HWMOD_BLOCK_WFI				(1 << 10)
 #define HWMOD_FORCE_MSTANDBY			(1 << 11)
+#define HWMOD_SWSUP_SIDLE_ACT			(1 << 12)
 
 /*
  * omap_hwmod._int_flags definitions
@@ -641,9 +645,6 @@ int omap_hwmod_read_hardreset(struct omap_hwmod *oh, const char *name);
 int omap_hwmod_enable_clocks(struct omap_hwmod *oh);
 int omap_hwmod_disable_clocks(struct omap_hwmod *oh);
 
-int omap_hwmod_set_slave_idlemode(struct omap_hwmod *oh, u8 idlemode);
-int omap_hwmod_set_ocp_autoidle(struct omap_hwmod *oh, u8 autoidle);
-
 int omap_hwmod_reset(struct omap_hwmod *oh);
 void omap_hwmod_ocp_barrier(struct omap_hwmod *oh);
 

arch/arm/mach-omap2/omap_hwmod_2xxx_ipblock_data.c

@@ -512,6 +512,7 @@ struct omap_hwmod omap2xxx_uart1_hwmod = {
 	.mpu_irqs	= omap2_uart1_mpu_irqs,
 	.sdma_reqs	= omap2_uart1_sdma_reqs,
 	.main_clk	= "uart1_fck",
+	.flags		= HWMOD_SWSUP_SIDLE_ACT,
 	.prcm		= {
 		.omap2 = {
 			.module_offs = CORE_MOD,
@@ -531,6 +532,7 @@ struct omap_hwmod omap2xxx_uart2_hwmod = {
 	.mpu_irqs	= omap2_uart2_mpu_irqs,
 	.sdma_reqs	= omap2_uart2_sdma_reqs,
 	.main_clk	= "uart2_fck",
+	.flags		= HWMOD_SWSUP_SIDLE_ACT,
 	.prcm		= {
 		.omap2 = {
 			.module_offs = CORE_MOD,
@@ -550,6 +552,7 @@ struct omap_hwmod omap2xxx_uart3_hwmod = {
 	.mpu_irqs	= omap2_uart3_mpu_irqs,
 	.sdma_reqs	= omap2_uart3_sdma_reqs,
 	.main_clk	= "uart3_fck",
+	.flags		= HWMOD_SWSUP_SIDLE_ACT,
 	.prcm		= {
 		.omap2 = {
 			.module_offs = CORE_MOD,

arch/arm/mach-omap2/omap_hwmod_33xx_data.c

@@ -1995,6 +1995,7 @@ static struct omap_hwmod am33xx_uart1_hwmod = {
 	.name		= "uart1",
 	.class		= &uart_class,
 	.clkdm_name	= "l4_wkup_clkdm",
+	.flags		= HWMOD_SWSUP_SIDLE_ACT,
 	.mpu_irqs	= am33xx_uart1_irqs,
 	.sdma_reqs	= uart1_edma_reqs,
 	.main_clk	= "dpll_per_m2_div4_wkupdm_ck",
@@ -2015,6 +2016,7 @@ static struct omap_hwmod am33xx_uart2_hwmod = {
 	.name		= "uart2",
 	.class		= &uart_class,
 	.clkdm_name	= "l4ls_clkdm",
+	.flags		= HWMOD_SWSUP_SIDLE_ACT,
 	.mpu_irqs	= am33xx_uart2_irqs,
 	.sdma_reqs	= uart1_edma_reqs,
 	.main_clk	= "dpll_per_m2_div4_ck",
@@ -2042,6 +2044,7 @@ static struct omap_hwmod am33xx_uart3_hwmod = {
 	.name		= "uart3",
 	.class		= &uart_class,
 	.clkdm_name	= "l4ls_clkdm",
+	.flags		= HWMOD_SWSUP_SIDLE_ACT,
 	.mpu_irqs	= am33xx_uart3_irqs,
 	.sdma_reqs	= uart3_edma_reqs,
 	.main_clk	= "dpll_per_m2_div4_ck",
@@ -2062,6 +2065,7 @@ static struct omap_hwmod am33xx_uart4_hwmod = {
 	.name		= "uart4",
 	.class		= &uart_class,
 	.clkdm_name	= "l4ls_clkdm",
+	.flags		= HWMOD_SWSUP_SIDLE_ACT,
 	.mpu_irqs	= am33xx_uart4_irqs,
 	.sdma_reqs	= uart1_edma_reqs,
 	.main_clk	= "dpll_per_m2_div4_ck",
@@ -2082,6 +2086,7 @@ static struct omap_hwmod am33xx_uart5_hwmod = {
 	.name		= "uart5",
 	.class		= &uart_class,
 	.clkdm_name	= "l4ls_clkdm",
+	.flags		= HWMOD_SWSUP_SIDLE_ACT,
 	.mpu_irqs	= am33xx_uart5_irqs,
 	.sdma_reqs	= uart1_edma_reqs,
 	.main_clk	= "dpll_per_m2_div4_ck",
@@ -2102,6 +2107,7 @@ static struct omap_hwmod am33xx_uart6_hwmod = {
 	.name		= "uart6",
 	.class		= &uart_class,
 	.clkdm_name	= "l4ls_clkdm",
+	.flags		= HWMOD_SWSUP_SIDLE_ACT,
 	.mpu_irqs	= am33xx_uart6_irqs,
 	.sdma_reqs	= uart1_edma_reqs,
 	.main_clk	= "dpll_per_m2_div4_ck",

arch/arm/mach-omap2/omap_hwmod_3xxx_data.c

@@ -490,6 +490,7 @@ static struct omap_hwmod omap3xxx_uart1_hwmod = {
 	.mpu_irqs	= omap2_uart1_mpu_irqs,
 	.sdma_reqs	= omap2_uart1_sdma_reqs,
 	.main_clk	= "uart1_fck",
+	.flags		= HWMOD_SWSUP_SIDLE_ACT,
 	.prcm		= {
 		.omap2 = {
 			.module_offs = CORE_MOD,
@@ -508,6 +509,7 @@ static struct omap_hwmod omap3xxx_uart2_hwmod = {
 	.mpu_irqs	= omap2_uart2_mpu_irqs,
 	.sdma_reqs	= omap2_uart2_sdma_reqs,
 	.main_clk	= "uart2_fck",
+	.flags		= HWMOD_SWSUP_SIDLE_ACT,
 	.prcm		= {
 		.omap2 = {
 			.module_offs = CORE_MOD,
@@ -526,6 +528,7 @@ static struct omap_hwmod omap3xxx_uart3_hwmod = {
 	.mpu_irqs	= omap2_uart3_mpu_irqs,
 	.sdma_reqs	= omap2_uart3_sdma_reqs,
 	.main_clk	= "uart3_fck",
+	.flags		= HWMOD_SWSUP_SIDLE_ACT,
 	.prcm		= {
 		.omap2 = {
 			.module_offs = OMAP3430_PER_MOD,
@@ -555,6 +558,7 @@ static struct omap_hwmod omap36xx_uart4_hwmod = {
 	.mpu_irqs	= uart4_mpu_irqs,
 	.sdma_reqs	= uart4_sdma_reqs,
 	.main_clk	= "uart4_fck",
+	.flags		= HWMOD_SWSUP_SIDLE_ACT,
 	.prcm		= {
 		.omap2 = {
 			.module_offs = OMAP3430_PER_MOD,

arch/arm/mach-omap2/omap_hwmod_44xx_data.c

@@ -3434,6 +3434,7 @@ static struct omap_hwmod omap44xx_uart1_hwmod = {
 	.name		= "uart1",
 	.class		= &omap44xx_uart_hwmod_class,
 	.clkdm_name	= "l4_per_clkdm",
+	.flags		= HWMOD_SWSUP_SIDLE_ACT,
 	.mpu_irqs	= omap44xx_uart1_irqs,
 	.sdma_reqs	= omap44xx_uart1_sdma_reqs,
 	.main_clk	= "func_48m_fclk",
@@ -3462,6 +3463,7 @@ static struct omap_hwmod omap44xx_uart2_hwmod = {
 	.name		= "uart2",
 	.class		= &omap44xx_uart_hwmod_class,
 	.clkdm_name	= "l4_per_clkdm",
+	.flags		= HWMOD_SWSUP_SIDLE_ACT,
 	.mpu_irqs	= omap44xx_uart2_irqs,
 	.sdma_reqs	= omap44xx_uart2_sdma_reqs,
 	.main_clk	= "func_48m_fclk",
@@ -3490,7 +3492,8 @@ static struct omap_hwmod omap44xx_uart3_hwmod = {
 	.name		= "uart3",
 	.class		= &omap44xx_uart_hwmod_class,
 	.clkdm_name	= "l4_per_clkdm",
-	.flags		= HWMOD_INIT_NO_IDLE | HWMOD_INIT_NO_RESET,
+	.flags		= HWMOD_INIT_NO_IDLE | HWMOD_INIT_NO_RESET |
+				HWMOD_SWSUP_SIDLE_ACT,
 	.mpu_irqs	= omap44xx_uart3_irqs,
 	.sdma_reqs	= omap44xx_uart3_sdma_reqs,
 	.main_clk	= "func_48m_fclk",
@@ -3519,6 +3522,7 @@ static struct omap_hwmod omap44xx_uart4_hwmod = {
 	.name		= "uart4",
 	.class		= &omap44xx_uart_hwmod_class,
 	.clkdm_name	= "l4_per_clkdm",
+	.flags		= HWMOD_SWSUP_SIDLE_ACT,
 	.mpu_irqs	= omap44xx_uart4_irqs,
 	.sdma_reqs	= omap44xx_uart4_sdma_reqs,
 	.main_clk	= "func_48m_fclk",

arch/arm/mach-omap2/serial.c

@@ -95,38 +95,9 @@ static void omap_uart_enable_wakeup(struct device *dev, bool enable)
 		omap_hwmod_disable_wakeup(od->hwmods[0]);
 }
 
-/*
- * Errata i291: [UART]:Cannot Acknowledge Idle Requests
- * in Smartidle Mode When Configured for DMA Operations.
- * WA: configure uart in force idle mode.
- */
-static void omap_uart_set_noidle(struct device *dev)
-{
-	struct platform_device *pdev = to_platform_device(dev);
-	struct omap_device *od = to_omap_device(pdev);
-
-	omap_hwmod_set_slave_idlemode(od->hwmods[0], HWMOD_IDLEMODE_NO);
-}
-
-static void omap_uart_set_smartidle(struct device *dev)
-{
-	struct platform_device *pdev = to_platform_device(dev);
-	struct omap_device *od = to_omap_device(pdev);
-	u8 idlemode;
-
-	if (od->hwmods[0]->class->sysc->idlemodes & SIDLE_SMART_WKUP)
-		idlemode = HWMOD_IDLEMODE_SMART_WKUP;
-	else
-		idlemode = HWMOD_IDLEMODE_SMART;
-
-	omap_hwmod_set_slave_idlemode(od->hwmods[0], idlemode);
-}
-
 #else
 static void omap_uart_enable_wakeup(struct device *dev, bool enable)
 {}
-static void omap_uart_set_noidle(struct device *dev) {}
-static void omap_uart_set_smartidle(struct device *dev) {}
 #endif /* CONFIG_PM */
 
 #ifdef CONFIG_OMAP_MUX
@@ -299,8 +270,6 @@ void __init omap_serial_init_port(struct omap_board_data *bdata,
 	omap_up.uartclk = OMAP24XX_BASE_BAUD * 16;
 	omap_up.flags = UPF_BOOT_AUTOCONF;
 	omap_up.get_context_loss_count = omap_pm_get_dev_context_loss_count;
-	omap_up.set_forceidle = omap_uart_set_smartidle;
-	omap_up.set_noidle = omap_uart_set_noidle;
 	omap_up.enable_wakeup = omap_uart_enable_wakeup;
 	omap_up.dma_rx_buf_size = info->dma_rx_buf_size;
 	omap_up.dma_rx_timeout = info->dma_rx_timeout;

arch/arm/mach-orion5x/common.c

@@ -199,13 +199,6 @@ void __init orion5x_init_early(void)
 
 	orion_time_set_base(TIMER_VIRT_BASE);
 
-	/*
-	 * Some Orion5x devices allocate their coherent buffers from atomic
-	 * context. Increase size of atomic coherent pool to make sure such
-	 * the allocations won't fail.
-	 */
-	init_dma_coherent_pool_size(SZ_1M);
-
 	/* Initialize the MBUS driver */
 	orion5x_pcie_id(&dev, &rev);
 	if (dev == MV88F5281_DEV_ID)

arch/arm/mach-shmobile/board-marzen.c

@@ -212,8 +212,8 @@ static struct platform_device *marzen_devices[] __initdata = {
 static struct usb_phy *phy;
 static int usb_power_on(struct platform_device *pdev)
 {
-	if (!phy)
-		return -EIO;
+	if (IS_ERR(phy))
+		return PTR_ERR(phy);
 
 	pm_runtime_enable(&pdev->dev);
 	pm_runtime_get_sync(&pdev->dev);
@@ -225,7 +225,7 @@ static int usb_power_on(struct platform_device *pdev)
 
 static void usb_power_off(struct platform_device *pdev)
 {
-	if (!phy)
+	if (IS_ERR(phy))
 		return;
 
 	usb_phy_shutdown(phy);

arch/arm/mach-sunxi/Kconfig

@@ -1,5 +1,6 @@
 config ARCH_SUNXI
 	bool "Allwinner A1X SOCs" if ARCH_MULTI_V7
+	select ARCH_REQUIRE_GPIOLIB
 	select CLKSRC_MMIO
 	select CLKSRC_OF
 	select COMMON_CLK

arch/arm/mach-tegra/tegra2_emc.c

@@ -307,11 +307,6 @@ static int tegra_emc_probe(struct platform_device *pdev)
 	}
 
 	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
-	if (!res) {
-		dev_err(&pdev->dev, "missing register base\n");
-		return -ENOMEM;
-	}
-
 	emc_regbase = devm_ioremap_resource(&pdev->dev, res);
 	if (IS_ERR(emc_regbase))
 		return PTR_ERR(emc_regbase);

arch/arm/mach-ux500/Kconfig

@@ -51,6 +51,7 @@ config MACH_MOP500
 	bool "U8500 Development platform, MOP500 versions"
 	select I2C
 	select I2C_NOMADIK
+	select REGULATOR
 	select REGULATOR_FIXED_VOLTAGE
 	select SOC_BUS
 	select UX500_SOC_DB8500

arch/arm/mach-ux500/board-mop500.c

@@ -623,7 +623,7 @@ static void __init mop500_init_machine(void)
 	sdi0_reg_info.gpios[0].gpio = GPIO_SDMMC_1V8_3V_SEL;
 
 	mop500_pinmaps_init();
-	parent = u8500_init_devices(&ab8500_platdata);
+	parent = u8500_init_devices();
 
 	for (i = 0; i < ARRAY_SIZE(mop500_platform_devs); i++)
 		mop500_platform_devs[i]->dev.parent = parent;
@@ -660,7 +660,7 @@ static void __init snowball_init_machine(void)
 	sdi0_reg_info.gpios[0].gpio = SNOWBALL_SDMMC_1V8_3V_GPIO;
 
 	snowball_pinmaps_init();
-	parent = u8500_init_devices(&ab8500_platdata);
+	parent = u8500_init_devices();
 
 	for (i = 0; i < ARRAY_SIZE(snowball_platform_devs); i++)
 		snowball_platform_devs[i]->dev.parent = parent;
@@ -698,7 +698,7 @@ static void __init hrefv60_init_machine(void)
 	sdi0_reg_info.gpios[0].gpio = HREFV60_SDMMC_1V8_3V_GPIO;
 
 	hrefv60_pinmaps_init();
-	parent = u8500_init_devices(&ab8500_platdata);
+	parent = u8500_init_devices();
 
 	for (i = 0; i < ARRAY_SIZE(mop500_platform_devs); i++)
 		mop500_platform_devs[i]->dev.parent = parent;

arch/arm/mach-ux500/cpu-db8500.c

@@ -206,7 +206,7 @@ static struct device * __init db8500_soc_device_init(void)
 /*
  * This function is called from the board init
  */
-struct device * __init u8500_init_devices(struct ab8500_platform_data *ab8500)
+struct device * __init u8500_init_devices(void)
 {
 	struct device *parent;
 	int i;
@@ -220,8 +220,6 @@ struct device * __init u8500_init_devices(struct ab8500_platform_data *ab8500)
 	for (i = 0; i < ARRAY_SIZE(platform_devs); i++)
 		platform_devs[i]->dev.parent = parent;
 
-	db8500_prcmu_device.dev.platform_data = ab8500;
-
 	platform_add_devices(platform_devs, ARRAY_SIZE(platform_devs));
 
 	return parent;
@@ -278,7 +276,7 @@ static struct of_dev_auxdata u8500_auxdata_lookup[] __initdata = {
 	OF_DEV_AUXDATA("st,nomadik-i2c", 0x8012a000, "nmk-i2c.4", NULL),
 	OF_DEV_AUXDATA("stericsson,db8500-prcmu", 0x80157000, "db8500-prcmu",
 			&db8500_prcmu_pdata),
-	OF_DEV_AUXDATA("smsc,lan9115", 0x50000000, "smsc911x", NULL),
+	OF_DEV_AUXDATA("smsc,lan9115", 0x50000000, "smsc911x.0", NULL),
 	/* Requires device name bindings. */
 	OF_DEV_AUXDATA("stericsson,nmk-pinctrl", U8500_PRCMU_BASE,
 		"pinctrl-db8500", NULL),

arch/arm/mach-ux500/setup.h

@@ -18,7 +18,7 @@
 void __init ux500_map_io(void);
 extern void __init u8500_map_io(void);
 
-extern struct device * __init u8500_init_devices(struct ab8500_platform_data *ab8500);
+extern struct device * __init u8500_init_devices(void);
 
 extern void __init ux500_init_irq(void);
 extern void __init ux500_init_late(void);

arch/arm/mach-vt8500/vt8500.c

@@ -173,6 +173,7 @@ static const char * const vt8500_dt_compat[] = {
 	"wm,wm8505",
 	"wm,wm8750",
 	"wm,wm8850",
+	NULL
 };
 
 DT_MACHINE_START(WMT_DT, "VIA/Wondermedia SoC (Device Tree Support)")

arch/arm/plat-orion/common.c

@@ -383,7 +383,7 @@ static struct resource orion_ge10_shared_resources[] = {
 
 static struct platform_device orion_ge10_shared = {
 	.name		= MV643XX_ETH_SHARED_NAME,
-	.id		= 1,
+	.id		= 2,
 	.dev		= {
 		.platform_data	= &orion_ge10_shared_data,
 	},
@@ -398,8 +398,8 @@ static struct resource orion_ge10_resources[] = {
 
 static struct platform_device orion_ge10 = {
 	.name		= MV643XX_ETH_NAME,
-	.id		= 1,
-	.num_resources	= 2,
+	.id		= 2,
+	.num_resources	= 1,
 	.resource	= orion_ge10_resources,
 	.dev		= {
 		.coherent_dma_mask	= DMA_BIT_MASK(32),
@@ -432,7 +432,7 @@ static struct resource orion_ge11_shared_resources[] = {
 
 static struct platform_device orion_ge11_shared = {
 	.name		= MV643XX_ETH_SHARED_NAME,
-	.id		= 1,
+	.id		= 3,
 	.dev		= {
 		.platform_data	= &orion_ge11_shared_data,
 	},
@@ -447,8 +447,8 @@ static struct resource orion_ge11_resources[] = {
 
 static struct platform_device orion_ge11 = {
 	.name		= MV643XX_ETH_NAME,
-	.id		= 1,
-	.num_resources	= 2,
+	.id		= 3,
+	.num_resources	= 1,
 	.resource	= orion_ge11_resources,
 	.dev		= {
 		.coherent_dma_mask	= DMA_BIT_MASK(32),

arch/arm/plat-orion/include/plat/common.h

@@ -10,6 +10,7 @@
 
 #ifndef __PLAT_COMMON_H
 #include <linux/mv643xx_eth.h>
+#include <linux/platform_data/usb-ehci-orion.h>
 
 struct dsa_platform_data;
 struct mv_sata_platform_data;

arch/arm/plat-samsung/adc.c

@@ -381,11 +381,6 @@ static int s3c_adc_probe(struct platform_device *pdev)
 	}
 
 	regs = platform_get_resource(pdev, IORESOURCE_MEM, 0);
-	if (!regs) {
-		dev_err(dev, "failed to find registers\n");
-		return -ENXIO;
-	}
-
 	adc->regs = devm_ioremap_resource(dev, regs);
 	if (IS_ERR(adc->regs))
 		return PTR_ERR(adc->regs);

arch/arm/vfp/entry.S

@@ -60,7 +60,7 @@ ENTRY(vfp_testing_entry)
 	str	r11, [r10, #TI_PREEMPT]
 #endif
 	ldr	r0, VFP_arch_address
-	str	r5, [r0]		@ known non-zero value
+	str	r0, [r0]		@ set to non-zero value
 	mov	pc, r9			@ we have handled the fault
 ENDPROC(vfp_testing_entry)
 

arch/arm/xen/enlighten.c

@@ -152,11 +152,12 @@ int xen_unmap_domain_mfn_range(struct vm_area_struct *vma,
 }
 EXPORT_SYMBOL_GPL(xen_unmap_domain_mfn_range);
 
-static int __init xen_secondary_init(unsigned int cpu)
+static void __init xen_percpu_init(void *unused)
 {
 	struct vcpu_register_vcpu_info info;
 	struct vcpu_info *vcpup;
 	int err;
+	int cpu = get_cpu();
 
 	pr_info("Xen: initializing cpu%d\n", cpu);
 	vcpup = per_cpu_ptr(xen_vcpu_info, cpu);
@@ -165,14 +166,10 @@ static int __init xen_secondary_init(unsigned int cpu)
 	info.offset = offset_in_page(vcpup);
 
 	err = HYPERVISOR_vcpu_op(VCPUOP_register_vcpu_info, cpu, &info);
-	if (err) {
-		pr_debug("register_vcpu_info failed: err=%d\n", err);
-	} else {
-		/* This cpu is using the registered vcpu info, even if
-		   later ones fail to. */
-		per_cpu(xen_vcpu, cpu) = vcpup;
-	}
-	return 0;
+	BUG_ON(err);
+	per_cpu(xen_vcpu, cpu) = vcpup;
+
+	enable_percpu_irq(xen_events_irq, 0);
 }
 
 static void xen_restart(char str, const char *cmd)
@@ -208,7 +205,6 @@ static int __init xen_guest_init(void)
 	const char *version = NULL;
 	const char *xen_prefix = "xen,xen-";
 	struct resource res;
-	int i;
 
 	node = of_find_compatible_node(NULL, NULL, "xen,xen");
 	if (!node) {
@@ -265,19 +261,23 @@ static int __init xen_guest_init(void)
 			                       sizeof(struct vcpu_info));
 	if (xen_vcpu_info == NULL)
 		return -ENOMEM;
-	for_each_online_cpu(i)
-		xen_secondary_init(i);
 
 	gnttab_init();
 	if (!xen_initial_domain())
 		xenbus_probe(NULL);
 
+	return 0;
+}
+core_initcall(xen_guest_init);
+
+static int __init xen_pm_init(void)
+{
 	pm_power_off = xen_power_off;
 	arm_pm_restart = xen_restart;
 
 	return 0;
 }
-core_initcall(xen_guest_init);
+subsys_initcall(xen_pm_init);
 
 static irqreturn_t xen_arm_callback(int irq, void *arg)
 {
@@ -285,11 +285,6 @@ static irqreturn_t xen_arm_callback(int irq, void *arg)
 	return IRQ_HANDLED;
 }
 
-static __init void xen_percpu_enable_events(void *unused)
-{
-	enable_percpu_irq(xen_events_irq, 0);
-}
-
 static int __init xen_init_events(void)
 {
 	if (!xen_domain() || xen_events_irq < 0)
@@ -303,7 +298,7 @@ static int __init xen_init_events(void)
 		return -EINVAL;
 	}
 
-	on_each_cpu(xen_percpu_enable_events, NULL, 0);
+	on_each_cpu(xen_percpu_init, NULL, 0);
 
 	return 0;
 }

arch/arm64/Kconfig

@@ -122,8 +122,6 @@ endmenu
 
 menu "Kernel Features"
 
-source "kernel/time/Kconfig"
-
 config ARM64_64K_PAGES
 	bool "Enable 64KB pages support"
 	help

arch/arm64/include/asm/assembler.h

@@ -82,7 +82,7 @@
 
 	.macro	enable_dbg_if_not_stepping, tmp
 	mrs	\tmp, mdscr_el1
-	tbnz	\tmp, #1, 9990f
+	tbnz	\tmp, #0, 9990f
 	enable_dbg
 9990:
 	.endm

arch/arm64/kernel/debug-monitors.c

@@ -136,8 +136,6 @@ void disable_debug_monitors(enum debug_el el)
  */
 static void clear_os_lock(void *unused)
 {
-	asm volatile("msr mdscr_el1, %0" : : "r" (0));
-	isb();
 	asm volatile("msr oslar_el1, %0" : : "r" (0));
 	isb();
 }

arch/arm64/kernel/early_printk.c

@@ -95,7 +95,7 @@ static void early_write(struct console *con, const char *s, unsigned n)
 	}
 }
 
-static struct console early_console = {
+static struct console early_console_dev = {
 	.name =		"earlycon",
 	.write =	early_write,
 	.flags =	CON_PRINTBUFFER | CON_BOOT,
@@ -145,7 +145,8 @@ static int __init setup_early_printk(char *buf)
 		early_base = early_io_map(paddr, EARLYCON_IOBASE);
 
 	printch = match->printch;
-	register_console(&early_console);
+	early_console = &early_console_dev;
+	register_console(&early_console_dev);
 
 	return 0;
 }

arch/arm64/kernel/setup.c

@@ -282,12 +282,13 @@ void __init setup_arch(char **cmdline_p)
 #endif
 }
 
-static int __init arm64_of_clk_init(void)
+static int __init arm64_device_init(void)
 {
 	of_clk_init(NULL);
+	of_platform_populate(NULL, of_default_bus_match_table, NULL, NULL);
 	return 0;
 }
-arch_initcall(arm64_of_clk_init);
+arch_initcall(arm64_device_init);
 
 static DEFINE_PER_CPU(struct cpu, cpu_data);
 
@@ -305,13 +306,6 @@ static int __init topology_init(void)
 }
 subsys_initcall(topology_init);
 
-static int __init arm64_device_probe(void)
-{
-	of_platform_populate(NULL, of_default_bus_match_table, NULL, NULL);
-	return 0;
-}
-device_initcall(arm64_device_probe);
-
 static const char *hwcap_str[] = {
 	"fp",
 	"asimd",

arch/arm64/mm/cache.S

@@ -52,7 +52,7 @@ loop1:
 	add	x2, x2, #4			// add 4 (line length offset)
 	mov	x4, #0x3ff
 	and	x4, x4, x1, lsr #3		// find maximum number on the way size
-	clz	x5, x4				// find bit position of way size increment
+	clz	w5, w4				// find bit position of way size increment
 	mov	x7, #0x7fff
 	and	x7, x7, x1, lsr #13		// extract max number of the index size
 loop2:

arch/arm64/mm/proc.S

@@ -119,8 +119,7 @@ ENTRY(__cpu_setup)
 
 	mov	x0, #3 << 20
 	msr	cpacr_el1, x0			// Enable FP/ASIMD
-	mov	x0, #1
-	msr	oslar_el1, x0			// Set the debug OS lock
+	msr	mdscr_el1, xzr			// Reset mdscr_el1
 	tlbi	vmalle1is			// invalidate I + D TLBs
 	/*
 	 * Memory region attributes for LPAE:

arch/avr32/Kconfig

@@ -205,6 +205,11 @@ config ARCH_DISCONTIGMEM_ENABLE
 config ARCH_SPARSEMEM_ENABLE
 	def_bool n
 
+config NODES_SHIFT
+	int
+	default "2"
+	depends on NEED_MULTIPLE_NODES
+
 source "mm/Kconfig"
 
 config OWNERSHIP_TRACE

arch/avr32/include/asm/Kbuild

@@ -2,3 +2,4 @@
 generic-y	+= clkdev.h
 generic-y	+= exec.h
 generic-y	+= trace_clock.h
+generic-y	+= param.h

arch/avr32/include/asm/numnodes.h

@@ -1,7 +0,0 @@
-#ifndef __ASM_AVR32_NUMNODES_H
-#define __ASM_AVR32_NUMNODES_H
-
-/* Max 4 nodes */
-#define NODES_SHIFT	2
-
-#endif /* __ASM_AVR32_NUMNODES_H */

arch/avr32/include/asm/param.h

@@ -1,9 +0,0 @@
-#ifndef __ASM_AVR32_PARAM_H
-#define __ASM_AVR32_PARAM_H
-
-#include <uapi/asm/param.h>
-
-# define HZ		CONFIG_HZ
-# define USER_HZ	100		/* User interfaces are in "ticks" */
-# define CLOCKS_PER_SEC	(USER_HZ)	/* frequency at which times() counts */
-#endif /* __ASM_AVR32_PARAM_H */

arch/avr32/include/uapi/asm/Kbuild

@@ -33,3 +33,4 @@ header-y += termbits.h
 header-y += termios.h
 header-y += types.h
 header-y += unistd.h
+generic-y += param.h

arch/avr32/include/uapi/asm/param.h

@@ -1,18 +0,0 @@
-#ifndef _UAPI__ASM_AVR32_PARAM_H
-#define _UAPI__ASM_AVR32_PARAM_H
-
-
-#ifndef HZ
-# define HZ		100
-#endif
-
-/* TODO: Should be configurable */
-#define EXEC_PAGESIZE	4096
-
-#ifndef NOGROUP
-# define NOGROUP	(-1)
-#endif
-
-#define MAXHOSTNAMELEN	64
-
-#endif /* _UAPI__ASM_AVR32_PARAM_H */