ARM64: dts: meson-gxbb-wetek: add a wetek specific dtsi to cleanup hub and play2
This patch adds a specific wetek dtsi to handle the specific Hub and Play2 boards by no more depending on the p20x dtsi. This simplifies the hub and play2 dts and will avoid breaking these boards when adding p200 and p201 specific changes. Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> Signed-off-by: Kevin Hilman <khilman@baylibre.com>
This commit is contained in:
Neil Armstrong
Kevin Hilman
Родитель
c04ffa71ff
Коммит
fb72c03e0e
|
|
@ -6,50 +6,9 @@
|
|||
|
||||
/dts-v1/;
|
||||
|
||||
#include "meson-gxbb-p20x.dtsi"
|
||||
#include "meson-gxbb-wetek.dtsi"
|
||||
|
||||
/ {
|
||||
compatible = "wetek,hub", "amlogic,meson-gxbb";
|
||||
model = "WeTek Hub";
|
||||
|
||||
leds {
|
||||
compatible = "gpio-leds";
|
||||
|
||||
system {
|
||||
label = "wetek-play:system-status";
|
||||
gpios = <&gpio_ao GPIOAO_13 GPIO_ACTIVE_HIGH>;
|
||||
default-state = "on";
|
||||
panic-indicator;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&cvbs_connector {
|
||||
status = "disabled";
|
||||
};
|
||||
|
||||
ðmac {
|
||||
status = "okay";
|
||||
pinctrl-0 = <ð_rgmii_pins>;
|
||||
pinctrl-names = "default";
|
||||
|
||||
phy-handle = <ð_phy0>;
|
||||
phy-mode = "rgmii";
|
||||
|
||||
amlogic,tx-delay-ns = <2>;
|
||||
|
||||
snps,reset-gpio = <&gpio GPIOZ_14 0>;
|
||||
snps,reset-delays-us = <0 10000 1000000>;
|
||||
snps,reset-active-low;
|
||||
|
||||
mdio {
|
||||
compatible = "snps,dwmac-mdio";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
|
||||
eth_phy0: ethernet-phy@0 {
|
||||
/* Realtek RTL8211F (0x001cc916) */
|
||||
reg = <0>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
|
|
|||
|
|
@ -6,7 +6,7 @@
|
|||
|
||||
/dts-v1/;
|
||||
|
||||
#include "meson-gxbb-p20x.dtsi"
|
||||
#include "meson-gxbb-wetek.dtsi"
|
||||
#include <dt-bindings/input/input.h>
|
||||
|
||||
/ {
|
||||
|
|
@ -14,15 +14,6 @@
|
|||
model = "WeTek Play 2";
|
||||
|
||||
leds {
|
||||
compatible = "gpio-leds";
|
||||
|
||||
system {
|
||||
label = "wetek-play:system-status";
|
||||
gpios = <&gpio_ao GPIOAO_13 GPIO_ACTIVE_HIGH>;
|
||||
default-state = "on";
|
||||
panic-indicator;
|
||||
};
|
||||
|
||||
wifi {
|
||||
label = "wetek-play:wifi-status";
|
||||
gpios = <&gpio GPIODV_26 GPIO_ACTIVE_HIGH>;
|
||||
|
|
@ -48,78 +39,6 @@
|
|||
gpios = <&gpio_ao GPIOAO_3 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
};
|
||||
|
||||
cvbs-connector {
|
||||
compatible = "composite-video-connector";
|
||||
|
||||
port {
|
||||
cvbs_connector_in: endpoint {
|
||||
remote-endpoint = <&cvbs_vdac_out>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
hdmi-connector {
|
||||
compatible = "hdmi-connector";
|
||||
type = "a";
|
||||
|
||||
port {
|
||||
hdmi_connector_in: endpoint {
|
||||
remote-endpoint = <&hdmi_tx_tmds_out>;
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&cec_AO {
|
||||
status = "okay";
|
||||
pinctrl-0 = <&ao_cec_pins>;
|
||||
pinctrl-names = "default";
|
||||
hdmi-phandle = <&hdmi_tx>;
|
||||
};
|
||||
|
||||
&cvbs_vdac_port {
|
||||
cvbs_vdac_out: endpoint {
|
||||
remote-endpoint = <&cvbs_connector_in>;
|
||||
};
|
||||
};
|
||||
|
||||
ðmac {
|
||||
status = "okay";
|
||||
pinctrl-0 = <ð_rgmii_pins>;
|
||||
pinctrl-names = "default";
|
||||
|
||||
phy-handle = <ð_phy0>;
|
||||
phy-mode = "rgmii";
|
||||
|
||||
amlogic,tx-delay-ns = <2>;
|
||||
|
||||
snps,reset-gpio = <&gpio GPIOZ_14 0>;
|
||||
snps,reset-delays-us = <0 10000 1000000>;
|
||||
snps,reset-active-low;
|
||||
|
||||
mdio {
|
||||
compatible = "snps,dwmac-mdio";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
|
||||
eth_phy0: ethernet-phy@0 {
|
||||
/* Realtek RTL8211F (0x001cc916) */
|
||||
reg = <0>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&hdmi_tx {
|
||||
status = "okay";
|
||||
pinctrl-0 = <&hdmi_hpd_pins>, <&hdmi_i2c_pins>;
|
||||
pinctrl-names = "default";
|
||||
};
|
||||
|
||||
&hdmi_tx_tmds_port {
|
||||
hdmi_tx_tmds_out: endpoint {
|
||||
remote-endpoint = <&hdmi_connector_in>;
|
||||
};
|
||||
};
|
||||
|
||||
&i2c_A {
|
||||
|
|
@ -127,3 +46,11 @@
|
|||
pinctrl-0 = <&i2c_a_pins>;
|
||||
pinctrl-names = "default";
|
||||
};
|
||||
|
||||
&usb1_phy {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&usb1 {
|
||||
status = "okay";
|
||||
};
|
||||
|
|
|
|||
|
|
@ -0,0 +1,256 @@
|
|||
// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
|
||||
/*
|
||||
* Copyright (c) 2016 Andreas Färber
|
||||
* Copyright (c) 2016 BayLibre, Inc.
|
||||
* Author: Kevin Hilman <khilman@kernel.org>
|
||||
*/
|
||||
|
||||
#include "meson-gxbb.dtsi"
|
||||
|
||||
/ {
|
||||
aliases {
|
||||
serial0 = &uart_AO;
|
||||
ethernet0 = ðmac;
|
||||
};
|
||||
|
||||
chosen {
|
||||
stdout-path = "serial0:115200n8";
|
||||
};
|
||||
|
||||
memory@0 {
|
||||
device_type = "memory";
|
||||
reg = <0x0 0x0 0x0 0x40000000>;
|
||||
};
|
||||
|
||||
leds {
|
||||
compatible = "gpio-leds";
|
||||
|
||||
system {
|
||||
label = "wetek-play:system-status";
|
||||
gpios = <&gpio_ao GPIOAO_13 GPIO_ACTIVE_HIGH>;
|
||||
default-state = "on";
|
||||
panic-indicator;
|
||||
};
|
||||
};
|
||||
|
||||
usb_pwr: regulator-usb-pwrs {
|
||||
compatible = "regulator-fixed";
|
||||
|
||||
regulator-name = "USB_PWR";
|
||||
|
||||
regulator-min-microvolt = <5000000>;
|
||||
regulator-max-microvolt = <5000000>;
|
||||
|
||||
gpio = <&gpio GPIODV_24 GPIO_ACTIVE_HIGH>;
|
||||
enable-active-high;
|
||||
};
|
||||
|
||||
vddio_boot: regulator-vddio_boot {
|
||||
compatible = "regulator-fixed";
|
||||
regulator-name = "VDDIO_BOOT";
|
||||
regulator-min-microvolt = <1800000>;
|
||||
regulator-max-microvolt = <1800000>;
|
||||
};
|
||||
|
||||
vddao_3v3: regulator-vddao_3v3 {
|
||||
compatible = "regulator-fixed";
|
||||
regulator-name = "VDDAO_3V3";
|
||||
regulator-min-microvolt = <3300000>;
|
||||
regulator-max-microvolt = <3300000>;
|
||||
};
|
||||
|
||||
vcc_3v3: regulator-vcc_3v3 {
|
||||
compatible = "regulator-fixed";
|
||||
regulator-name = "VCC_3V3";
|
||||
regulator-min-microvolt = <3300000>;
|
||||
regulator-max-microvolt = <3300000>;
|
||||
};
|
||||
|
||||
emmc_pwrseq: emmc-pwrseq {
|
||||
compatible = "mmc-pwrseq-emmc";
|
||||
reset-gpios = <&gpio BOOT_9 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
wifi32k: wifi32k {
|
||||
compatible = "pwm-clock";
|
||||
#clock-cells = <0>;
|
||||
clock-frequency = <32768>;
|
||||
pwms = <&pwm_ef 0 30518 0>; /* PWM_E at 32.768KHz */
|
||||
};
|
||||
|
||||
sdio_pwrseq: sdio-pwrseq {
|
||||
compatible = "mmc-pwrseq-simple";
|
||||
reset-gpios = <&gpio GPIOX_6 GPIO_ACTIVE_LOW>;
|
||||
clocks = <&wifi32k>;
|
||||
clock-names = "ext_clock";
|
||||
};
|
||||
|
||||
cvbs-connector {
|
||||
compatible = "composite-video-connector";
|
||||
|
||||
port {
|
||||
cvbs_connector_in: endpoint {
|
||||
remote-endpoint = <&cvbs_vdac_out>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
hdmi-connector {
|
||||
compatible = "hdmi-connector";
|
||||
type = "a";
|
||||
|
||||
port {
|
||||
hdmi_connector_in: endpoint {
|
||||
remote-endpoint = <&hdmi_tx_tmds_out>;
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&cec_AO {
|
||||
status = "okay";
|
||||
pinctrl-0 = <&ao_cec_pins>;
|
||||
pinctrl-names = "default";
|
||||
hdmi-phandle = <&hdmi_tx>;
|
||||
};
|
||||
|
||||
&cvbs_vdac_port {
|
||||
cvbs_vdac_out: endpoint {
|
||||
remote-endpoint = <&cvbs_connector_in>;
|
||||
};
|
||||
};
|
||||
|
||||
ðmac {
|
||||
status = "okay";
|
||||
pinctrl-0 = <ð_rgmii_pins>;
|
||||
pinctrl-names = "default";
|
||||
|
||||
phy-handle = <ð_phy0>;
|
||||
phy-mode = "rgmii";
|
||||
|
||||
amlogic,tx-delay-ns = <2>;
|
||||
|
||||
snps,reset-gpio = <&gpio GPIOZ_14 0>;
|
||||
snps,reset-delays-us = <0 10000 1000000>;
|
||||
snps,reset-active-low;
|
||||
|
||||
mdio {
|
||||
compatible = "snps,dwmac-mdio";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
|
||||
eth_phy0: ethernet-phy@0 {
|
||||
/* Realtek RTL8211F (0x001cc916) */
|
||||
reg = <0>;
|
||||
eee-broken-1000t;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&hdmi_tx {
|
||||
status = "okay";
|
||||
pinctrl-0 = <&hdmi_hpd_pins>, <&hdmi_i2c_pins>;
|
||||
pinctrl-names = "default";
|
||||
};
|
||||
|
||||
&hdmi_tx_tmds_port {
|
||||
hdmi_tx_tmds_out: endpoint {
|
||||
remote-endpoint = <&hdmi_connector_in>;
|
||||
};
|
||||
};
|
||||
|
||||
&ir {
|
||||
status = "okay";
|
||||
pinctrl-0 = <&remote_input_ao_pins>;
|
||||
pinctrl-names = "default";
|
||||
};
|
||||
|
||||
&pwm_ef {
|
||||
status = "okay";
|
||||
pinctrl-0 = <&pwm_e_pins>;
|
||||
pinctrl-names = "default";
|
||||
clocks = <&clkc CLKID_FCLK_DIV4>;
|
||||
clock-names = "clkin0";
|
||||
};
|
||||
|
||||
/* Wireless SDIO Module */
|
||||
&sd_emmc_a {
|
||||
status = "okay";
|
||||
pinctrl-0 = <&sdio_pins>;
|
||||
pinctrl-1 = <&sdio_clk_gate_pins>;
|
||||
pinctrl-names = "default", "clk-gate";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
|
||||
bus-width = <4>;
|
||||
cap-sd-highspeed;
|
||||
max-frequency = <100000000>;
|
||||
|
||||
non-removable;
|
||||
disable-wp;
|
||||
|
||||
mmc-pwrseq = <&sdio_pwrseq>;
|
||||
|
||||
vmmc-supply = <&vddao_3v3>;
|
||||
vqmmc-supply = <&vddio_boot>;
|
||||
|
||||
brcmf: wifi@1 {
|
||||
reg = <1>;
|
||||
compatible = "brcm,bcm4329-fmac";
|
||||
};
|
||||
};
|
||||
|
||||
/* SD card */
|
||||
&sd_emmc_b {
|
||||
status = "okay";
|
||||
pinctrl-0 = <&sdcard_pins>;
|
||||
pinctrl-1 = <&sdcard_clk_gate_pins>;
|
||||
pinctrl-names = "default", "clk-gate";
|
||||
|
||||
bus-width = <4>;
|
||||
cap-sd-highspeed;
|
||||
max-frequency = <100000000>;
|
||||
disable-wp;
|
||||
|
||||
cd-gpios = <&gpio CARD_6 GPIO_ACTIVE_HIGH>;
|
||||
cd-inverted;
|
||||
|
||||
vmmc-supply = <&vddao_3v3>;
|
||||
vqmmc-supply = <&vcc_3v3>;
|
||||
};
|
||||
|
||||
/* eMMC */
|
||||
&sd_emmc_c {
|
||||
status = "okay";
|
||||
pinctrl-0 = <&emmc_pins>, <&emmc_ds_pins>;
|
||||
pinctrl-1 = <&emmc_clk_gate_pins>;
|
||||
pinctrl-names = "default", "clk-gate";
|
||||
|
||||
bus-width = <8>;
|
||||
cap-mmc-highspeed;
|
||||
max-frequency = <200000000>;
|
||||
non-removable;
|
||||
disable-wp;
|
||||
mmc-ddr-1_8v;
|
||||
mmc-hs200-1_8v;
|
||||
|
||||
mmc-pwrseq = <&emmc_pwrseq>;
|
||||
vmmc-supply = <&vcc_3v3>;
|
||||
vqmmc-supply = <&vddio_boot>;
|
||||
};
|
||||
|
||||
/* This UART is brought out to the DB9 connector */
|
||||
&uart_AO {
|
||||
status = "okay";
|
||||
pinctrl-0 = <&uart_ao_a_pins>;
|
||||
pinctrl-names = "default";
|
||||
};
|
||||
|
||||
&usb0_phy {
|
||||
status = "okay";
|
||||
phy-supply = <&usb_pwr>;
|
||||
};
|
||||
|
||||
&usb0 {
|
||||
status = "okay";
|
||||
};
|
||||
Загрузка…
Ссылка в новой задаче