[MTD] [NAND] Blackfin NFC Driver: add support for the ECC layout the Blackfin bootrom uses

Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This commit is contained in:
Mike Frysinger 2008-07-30 12:35:01 -07:00 коммит произвёл David Woodhouse
Родитель cf840392e8
Коммит fcb90ba7e9
2 изменённых файлов: 52 добавлений и 0 удалений

Просмотреть файл

@ -109,6 +109,18 @@ config MTD_NAND_BF5XX_HWECC
Enable the use of the BF5XX's internal ECC generator when
using NAND.
config MTD_NAND_BF5XX_BOOTROM_ECC
bool "Use Blackfin BootROM ECC Layout"
default n
depends on MTD_NAND_BF5XX_HWECC
help
If you wish to modify NAND pages and allow the Blackfin on-chip
BootROM to boot from them, say Y here. This is only necessary
if you are booting U-Boot out of NAND and you wish to update
U-Boot from Linux' userspace. Otherwise, you should say N here.
If unsure, say N.
config MTD_NAND_RTC_FROM4
tristate "Renesas Flash ROM 4-slot interface board (FROM_BOARD4)"
depends on SH_SOLUTION_ENGINE

Просмотреть файл

@ -91,6 +91,41 @@ static const unsigned short bfin_nfc_pin_req[] =
P_NAND_ALE,
0};
#ifdef CONFIG_MTD_NAND_BF5XX_BOOTROM_ECC
static uint8_t bbt_pattern[] = { 0xff };
static struct nand_bbt_descr bootrom_bbt = {
.options = 0,
.offs = 63,
.len = 1,
.pattern = bbt_pattern,
};
static struct nand_ecclayout bootrom_ecclayout = {
.eccbytes = 24,
.eccpos = {
0x8 * 0, 0x8 * 0 + 1, 0x8 * 0 + 2,
0x8 * 1, 0x8 * 1 + 1, 0x8 * 1 + 2,
0x8 * 2, 0x8 * 2 + 1, 0x8 * 2 + 2,
0x8 * 3, 0x8 * 3 + 1, 0x8 * 3 + 2,
0x8 * 4, 0x8 * 4 + 1, 0x8 * 4 + 2,
0x8 * 5, 0x8 * 5 + 1, 0x8 * 5 + 2,
0x8 * 6, 0x8 * 6 + 1, 0x8 * 6 + 2,
0x8 * 7, 0x8 * 7 + 1, 0x8 * 7 + 2
},
.oobfree = {
{ 0x8 * 0 + 3, 5 },
{ 0x8 * 1 + 3, 5 },
{ 0x8 * 2 + 3, 5 },
{ 0x8 * 3 + 3, 5 },
{ 0x8 * 4 + 3, 5 },
{ 0x8 * 5 + 3, 5 },
{ 0x8 * 6 + 3, 5 },
{ 0x8 * 7 + 3, 5 },
}
};
#endif
/*
* Data structures for bf5xx nand flash controller driver
*/
@ -712,6 +747,11 @@ static int bf5xx_nand_probe(struct platform_device *pdev)
/* setup hardware ECC data struct */
if (hardware_ecc) {
#ifdef CONFIG_MTD_NAND_BF5XX_BOOTROM_ECC
chip->badblock_pattern = &bootrom_bbt;
chip->ecc.layout = &bootrom_ecclayout;
#endif
if (plat->page_size == NFC_PG_SIZE_256) {
chip->ecc.bytes = 3;
chip->ecc.size = 256;