[ Upstream commit 081a9b7c74 ]
It turns out the internal SATA reference clock signal will stay
unavailable for the SATA interface consumer until the buffer on it's way
is ungated. So aside with having the actual clock divider enabled we need
to ungate a buffer placed on the signal way to the SATA controller (most
likely some rudiment from the initial SoC release). Seeing the switch flag
is placed in the same register as the SATA-ref clock divider at a
non-standard ffset, let's implement it as a separate clock controller with
the set-rate propagation to the parental clock divider wrapper. As such
we'll be able to disable/enable and still change the original clock source
rate.
Fixes: 353afa3a8d ("clk: Add Baikal-T1 CCU Dividers driver")
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Link: https://lore.kernel.org/r/20220929225402.9696-5-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e2eef31276 ]
Baikal-T1 CCU reference manual says that both xGMAC reference and xGMAC
PTP clocks are generated by two different wrappers with the same constant
divider thus each producing a 156.25 MHz signal. But for some reason both
of these clock sources are gated by a single switch-flag in the CCU
registers space - CCU_SYS_XGMAC_BASE.BIT(0). In order to make the clocks
handled independently we need to define a shared parental gate so the base
clock signal would be switched off only if both of the child-clocks are
disabled.
Note the ID is intentionally set to -2 since we are going to add a one
more internal clock identifier in the next commit.
Fixes: 353afa3a8d ("clk: Add Baikal-T1 CCU Dividers driver")
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Link: https://lore.kernel.org/r/20220929225402.9696-4-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3c74208868 ]
Most likely due to copy-paste mistake the divider has been set to 10 while
according to the SoC reference manual it's supposed to be 8 thus having
PTP clock frequency of 156.25 MHz.
Fixes: 353afa3a8d ("clk: Add Baikal-T1 CCU Dividers driver")
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Link: https://lore.kernel.org/r/20220929225402.9696-3-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
There is a spelling mistake in a pr_err error message. Fix it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Link: https://lore.kernel.org/r/20200602121030.39132-1-colin.king@canonical.com
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Nearly each Baikal-T1 IP-core is supposed to have a clock source
of particular frequency. But since there are greater than five
IP-blocks embedded into the SoC, the CCU PLLs can't fulfill all the
needs. Baikal-T1 CCU provides a set of fixed and configurable clock
dividers in order to generate a necessary signal for each chip
sub-block.
This driver creates the of-based hardware clocks for each divider
available in Baikal-T1 CCU. The same way as for PLLs we split the
functionality up into the clocks operations (gate, ungate, set rate,
etc) and hardware clocks declaration/registration procedures.
In accordance with the CCU documentation all its dividers are distributed
into two CCU sub-blocks: AXI-bus and system devices reference clocks.
The former sub-block is used to supply the clocks for AXI-bus interfaces
(AXI clock domains) and the later one provides the SoC IP-cores reference
clocks. Each sub-block is represented by a dedicated DT node, so they
have different compatible strings to distinguish one from another.
For some reason CCU provides the dividers of different types. Some
dividers can be gateable some can't, some are fixed while the others
are variable, some have special divider' limitations, some've got a
non-standard register layout and so on. In order to cover all of these
cases the hardware clocks driver is designed with an info-descriptor
pattern. So there are special static descriptors declared for the
dividers of each type with additional flags describing the block
peculiarity. These descriptors are then used to create hardware clocks
with proper operations.
Some CCU dividers provide a way to reset a domain they generate
a clock for. So the CCU AXI-bus and CCU system devices clock
drivers also perform the reset controller registration.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Cc: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: linux-mips@vger.kernel.org
Cc: devicetree@vger.kernel.org
Link: https://lore.kernel.org/r/20200526222056.18072-5-Sergey.Semin@baikalelectronics.ru
[sboyd@kernel.org: Drop return from void function, silence sparse
warnings about initializing structs with NULL vs. integer]
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Serge Semin
Colin Ian King