commit da53c36ddd upstream.
A potential deadlock was found by Zheng Zhang with a local syzkaller
instance.
The problem is that when a non-blocking CEC transmit is canceled by calling
cec_data_cancel, that in turn can call the high-level received() driver
callback, which can call cec_transmit_msg() to transmit a new message.
The cec_data_cancel() function is called with the adap->lock mutex held,
and cec_transmit_msg() tries to take that same lock.
The root cause is that the received() callback can either be used to pass
on a received message (and then adap->lock is not held), or to report a
canceled transmit (and then adap->lock is held).
This is confusing, so create a new low-level adap_nb_transmit_canceled
callback that reports back that a non-blocking transmit was canceled.
And the received() callback is only called when a message is received,
as was the case before commit f9d0ecbf56 ("media: cec: correctly pass
on reply results") complicated matters.
Reported-by: Zheng Zhang <zheng.zhang@email.ucr.edu>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Fixes: f9d0ecbf56 ("media: cec: correctly pass on reply results")
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 47c82aac10a6954d68f29f10d9758d016e8e5af1 ]
Keep track if cec_claim_log_addrs() is running, and return -EBUSY
if it is when calling CEC_ADAP_S_LOG_ADDRS.
This prevents a case where cec_claim_log_addrs() could be called
while it was still in progress.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reported-by: Yang, Chenyuan <cy54@illinois.edu>
Closes: https://lore.kernel.org/linux-media/PH7PR11MB57688E64ADE4FE82E658D86DA09EA@PH7PR11MB5768.namprd11.prod.outlook.com/
Fixes: ca684386e6 ("[media] cec: add HDMI CEC framework (api)")
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f9222f8ca1 ]
Using an activation counter to decide when the enable or disable the
cec adapter is not the best approach and can lead to race conditions.
Change this to determining the current status of the adapter, and
enable or disable the adapter accordingly.
It now only needs to be called whenever there is a chance that the
state changes, and it can handle enabling/disabling monitoring as
well if needed.
This simplifies the code and it should be a more robust approach as well.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Stable-dep-of: 47c82aac10a6 ("media: cec: core: avoid recursive cec_claim_log_addrs")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 590a8e564c ]
If a transmit-in-progress was canceled, then, once the transmit
is done, mark it as aborted and refrain from retrying the transmit.
To signal this situation the new transmit_in_progress_aborted field is
set to true.
The old implementation would just set adap->transmitting to NULL and
set adap->transmit_in_progress to false, but on the hardware level
the transmit was still ongoing. However, the framework would think
the transmit was aborted, and if a new transmit was issued, then
it could overwrite the HW buffer containing the old transmit with the
new transmit, leading to garbled data on the CEC bus.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Stable-dep-of: 47c82aac10a6 ("media: cec: core: avoid recursive cec_claim_log_addrs")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3813c932ed ]
Don't enable/disable the adapter if the first fh is opened or the
last fh is closed, instead do this when the adapter is configured
or unconfigured, and also when we enter Monitor All or Monitor Pin
mode for the first time or we exit the Monitor All/Pin mode for the
last time.
However, if needs_hpd is true, then do this when the physical
address is set or cleared: in that case the adapter typically is
powered by the HPD, so it really is disabled when the HPD is low.
This case (needs_hpd is true) was already handled in this way, so
this wasn't changed.
The problem with the old behavior was that if the HPD goes low when
no fh is open, and a transmit was in progress, then the adapter would
be disabled, typically stopping the transmit immediately which
leaves a partial message on the bus, which isn't nice and can confuse
some adapters.
It makes much more sense to disable it only when the adapter is
unconfigured and we're not monitoring the bus, since then you really
won't be using it anymore.
To keep track of this store a CEC activation count and call adap_enable
only when it goes from 0 to 1 or back to 0.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Stable-dep-of: 47c82aac10a6 ("media: cec: core: avoid recursive cec_claim_log_addrs")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 56b5c3e67b ]
Getting below error when using KCSAN to check the driver. Adding lock to
protect parameter num_rdy when getting the value with function:
v4l2_m2m_num_src_bufs_ready/v4l2_m2m_num_dst_bufs_ready.
kworker/u16:3: [name:report&]BUG: KCSAN: data-race in v4l2_m2m_buf_queue
kworker/u16:3: [name:report&]
kworker/u16:3: [name:report&]read-write to 0xffffff8105f35b94 of 1 bytes by task 20865 on cpu 7:
kworker/u16:3: v4l2_m2m_buf_queue+0xd8/0x10c
Signed-off-by: Pina Chen <pina.chen@mediatek.com>
Signed-off-by: Yunfei Dong <yunfei.dong@mediatek.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 627bb528b0 ]
dvb_register_device() dynamically allocates fops with kmemdup()
to set the fops->owner.
And these fops are registered in 'file->f_ops' using replace_fops()
in the dvb_device_open() process, and kfree()d in dvb_free_device().
However, it is not common to use dynamically allocated fops instead
of 'static const' fops as an argument of replace_fops(),
and UAF may occur.
These UAFs can occur on any dvb type using dvb_register_device(),
such as dvb_dvr, dvb_demux, dvb_frontend, dvb_net, etc.
So, instead of kfree() the fops dynamically allocated in
dvb_register_device() in dvb_free_device() called during the
.disconnect() process, kfree() it collectively in exit_dvbdev()
called when the dvbdev.c module is removed.
Link: https://lore.kernel.org/linux-media/20221117045925.14297-4-imv4bel@gmail.com
Signed-off-by: Hyunwoo Kim <imv4bel@gmail.com>
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4172385b0c ]
A race condition may occur between the .disconnect function, which
is called when the device is disconnected, and the dvb_device_open()
function, which is called when the device node is open()ed.
This results in several types of UAFs.
The root cause of this is that you use the dvb_device_open() function,
which does not implement a conditional statement
that checks 'dvbnet->exit'.
So, add 'remove_mutex` to protect 'dvbnet->exit' and use
locked_dvb_net_open() function to check 'dvbnet->exit'.
[mchehab: fix a checkpatch warning]
Link: https://lore.kernel.org/linux-media/20221117045925.14297-3-imv4bel@gmail.com
Signed-off-by: Hyunwoo Kim <imv4bel@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 3edfd14bb5 upstream.
Previous commit that introduces reference counter does not add proper
comments, which will lead to warning when building htmldocs. Fix them.
Reported-by: "Stephen Rothwell" <sfr@canb.auug.org.au>
Fixes: 0fc044b2b5 ("media: dvbdev: adopts refcnt to avoid UAF")
Signed-off-by: Lin Ma <linma@zju.edu.cn>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 0fc044b2b5 ]
dvb_unregister_device() is known that prone to use-after-free.
That is, the cleanup from dvb_unregister_device() releases the dvb_device
even if there are pointers stored in file->private_data still refer to it.
This patch adds a reference counter into struct dvb_device and delays its
deallocation until no pointer refers to the object.
Link: https://lore.kernel.org/linux-media/20220807145952.10368-1-linma@zju.edu.cn
Signed-off-by: Lin Ma <linma@zju.edu.cn>
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2ba3e38517 ]
The state argument for the functions for obtaining various parts of the
state is NULL if it is called by drivers for active state. Fail graciously
in that case instead of dereferencing a NULL pointer.
Suggested-by: Bingbu Cao <bingbu.cao@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bb9ea2c31f ]
The doc says the I²C device's name is used if devname is NULL, but
actually the I²C device driver's name is used.
Fixes: 0658293012 ("media: v4l: subdev: Add a function to set an I²C sub-device's name")
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit a9e6107616 upstream.
The cec_devnode struct has a lock meant to serialize access
to the fields of this struct. This lock is taken during
device node (un)registration and when opening or releasing a
filehandle to the device node. When the last open filehandle
is closed the cec adapter might be disabled by calling the
adap_enable driver callback with the devnode.lock held.
However, if during that callback a message or event arrives
then the driver will call one of the cec_queue_event()
variants in cec-adap.c, and those will take the same devnode.lock
to walk the open filehandle list.
This obviously causes a deadlock.
This is quite easy to reproduce with the cec-gpio driver since that
uses the cec-pin framework which generated lots of events and uses
a kernel thread for the processing, so when adap_enable is called
the thread is still running and can generate events.
But I suspect that it might also happen with other drivers if an
interrupt arrives signaling e.g. a received message before adap_enable
had a chance to disable the interrupts.
This patch adds a new mutex to serialize access to the fhs list.
When adap_enable() is called the devnode.lock mutex is held, but
not devnode.lock_fhs. The event functions in cec-adap.c will now
use devnode.lock_fhs instead of devnode.lock, ensuring that it is
safe to call those functions from the adap_enable callback.
This specific issue only happens if the last open filehandle is closed
and the physical address is invalid. This is not something that
happens during normal operation, but it does happen when monitoring
CEC traffic (e.g. cec-ctl --monitor) with an unconfigured CEC adapter.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Cc: <stable@vger.kernel.org> # for v5.13 and up
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit a4b83deb3e ]
With the new DMA API we need an extension of the videobuf2 API.
Previously, videobuf2 core would set the non-coherent DMA bit
in the vb2_queue dma_attr field (if user-space would pass a
corresponding memory hint); the vb2 core then would pass the
vb2_queue dma_attrs to the vb2 allocators. The vb2 allocator
would use the queue's dma_attr and the DMA API would allocate
either coherent or non-coherent memory.
But we cannot do this anymore, since there is no corresponding DMA
attr flag and, hence, there is no way for the allocator to become
aware of what type of allocation user-space has requested. So we
need to pass more context from videobuf2 core to the allocators.
Fix this by changing the call_ptr_memop() macro to pass the
vb2 pointer to the corresponding op callbacks.
Signed-off-by: Sergey Senozhatsky <senozhatsky@chromium.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Add pre_streamon and post_streamoff callbacks that can be used to set a
CSI-2 transmitter to LP-11 or LP-111 mode. This can be used by receiver
drivers to reliably initialise the receiver when its initialisation
requires software involvement.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Fix kerneldoc syntax in v4l2-async. The references were not produced
correctly.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Fix the name of the function that registers the subdev_notifier member
of the v4l2_subdev structure.
[Sakari Ailus: Drop _sensor from the function name.]
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The s_learning_mode() function is called in response to the ioctl
LIRC_SET_WIDEBAND_RECEIVER, so rename it to s_wideband_receiver().
Learning mode is when both the wideband receiver is turned on and
carrier reports are enabled.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Any timeout larger than LIRC_VALUE_MASK cannot work for the lirc uapi.
LIRC_VALUE_MASK is about 16 seconds which is more than enough.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
If HEVC frame consists of multiple slices, segment address has to be
known in order to properly decode it.
Add segment address field to slice parameters.
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Add Geniatech MyGica T230C2_LITE and T230A as many people
are asking support for these devices on forums.
Link: https://lore.kernel.org/linux-media/YMuptIYFLdwSmw//@kali
Signed-off-by: Ján Čáni <pego149@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Smatch static checker warns that "mdev" can be null:
sound/usb/media.c:287 snd_media_device_create()
warn: 'mdev' can also be NULL
If CONFIG_MEDIA_CONTROLLER is disabled, this file should not be included
in the build.
The below conditions in the sound/usb/Makefile are in place to ensure that
media.c isn't included in the build.
sound/usb/Makefile:
snd-usb-audio-$(CONFIG_SND_USB_AUDIO_USE_MEDIA_CONTROLLER) += media.o
select SND_USB_AUDIO_USE_MEDIA_CONTROLLER if MEDIA_CONTROLLER &&
(MEDIA_SUPPORT=y || MEDIA_SUPPORT=SND_USB_AUDIO)
The following config check in include/media/media-dev-allocator.h is
in place to enable the API only when CONFIG_MEDIA_CONTROLLER and
CONFIG_USB are enabled.
#if defined(CONFIG_MEDIA_CONTROLLER) && defined(CONFIG_USB)
This check doesn't work as intended when CONFIG_USB=m. When CONFIG_USB=m,
CONFIG_USB_MODULE is defined and CONFIG_USB is not. The above config check
doesn't catch that CONFIG_USB is defined as a module and disables the API.
This results in sound/usb enabling Media Controller specific ALSA driver
code, while Media disables the Media Controller API.
Fix the problem requires two changes:
1. Change the check to use IS_ENABLED to detect when CONFIG_USB is enabled
as a module or static. Since CONFIG_MEDIA_CONTROLLER is a bool, leave
the check unchanged to be consistent with drivers/media/Makefile.
2. Change the drivers/media/mc/Makefile to include mc-dev-allocator.o
in mc-objs when CONFIG_USB is enabled.
Link: https://lore.kernel.org/alsa-devel/YLeAvT+R22FQ%2FEyw@mwanda/
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The saa6588_ioctl() function expects to get called from other kernel
functions with a 'saa6588_command' pointer, but I found nothing stops it
from getting called from user space instead, which seems rather dangerous.
The same thing happens in the davinci vpbe driver with its VENC_GET_FLD
command.
As a quick fix, add a separate .command() callback pointer for this
driver and change the two callers over to that. This change can easily
get backported to stable kernels if necessary, but since there are only
two drivers, we may want to eventually replace this with a set of more
specialized callbacks in the long run.
Fixes: c3fda7f835 ("V4L/DVB (10537): saa6588: convert to v4l2_subdev.")
Cc: stable@vger.kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
We have 'struct v4l2_subdev_pad_config' which contains configuration for
a single pad used for the TRY functionality, and an array of those
structs is passed to various v4l2_subdev_pad_ops.
I was working on subdev internal routing between pads, and realized that
there's no way to add TRY functionality for routes, which is not pad
specific configuration. Adding a separate struct for try-route config
wouldn't work either, as e.g. set-fmt needs to know the try-route
configuration to propagate the settings.
This patch adds a new struct, 'struct v4l2_subdev_state' (which at the
moment only contains the v4l2_subdev_pad_config array) and the new
struct is used in most of the places where v4l2_subdev_pad_config was
used. All v4l2_subdev_pad_ops functions taking v4l2_subdev_pad_config
are changed to instead take v4l2_subdev_state.
The changes to drivers/media/v4l2-core/v4l2-subdev.c and
include/media/v4l2-subdev.h were written by hand, and all the driver
changes were done with the semantic patch below. The spatch needs to be
applied to a select list of directories. I used the following shell
commands to apply the spatch:
dirs="drivers/media/i2c drivers/media/platform drivers/media/usb drivers/media/test-drivers/vimc drivers/media/pci drivers/staging/media"
for dir in $dirs; do spatch -j8 --dir --include-headers --no-show-diff --in-place --sp-file v4l2-subdev-state.cocci $dir; done
Note that Coccinelle chokes on a few drivers (gcc extensions?). With
minor changes we can make Coccinelle run fine, and these changes can be
reverted after spatch. The diff for these changes is:
For drivers/media/i2c/s5k5baf.c:
@@ -1481,7 +1481,7 @@ static int s5k5baf_set_selection(struct v4l2_subdev *sd,
&s5k5baf_cis_rect,
v4l2_subdev_get_try_crop(sd, cfg, PAD_CIS),
v4l2_subdev_get_try_compose(sd, cfg, PAD_CIS),
- v4l2_subdev_get_try_crop(sd, cfg, PAD_OUT)
+ v4l2_subdev_get_try_crop(sd, cfg, PAD_OUT),
};
s5k5baf_set_rect_and_adjust(rects, rtype, &sel->r);
return 0;
For drivers/media/platform/s3c-camif/camif-capture.c:
@@ -1230,7 +1230,7 @@ static int s3c_camif_subdev_get_fmt(struct v4l2_subdev *sd,
*mf = camif->mbus_fmt;
break;
- case CAMIF_SD_PAD_SOURCE_C...CAMIF_SD_PAD_SOURCE_P:
+ case CAMIF_SD_PAD_SOURCE_C:
/* crop rectangle at camera interface input */
mf->width = camif->camif_crop.width;
mf->height = camif->camif_crop.height;
@@ -1332,7 +1332,7 @@ static int s3c_camif_subdev_set_fmt(struct v4l2_subdev *sd,
}
break;
- case CAMIF_SD_PAD_SOURCE_C...CAMIF_SD_PAD_SOURCE_P:
+ case CAMIF_SD_PAD_SOURCE_C:
/* Pixel format can be only changed on the sink pad. */
mf->code = camif->mbus_fmt.code;
mf->width = crop->width;
The semantic patch is:
// <smpl>
// Change function parameter
@@
identifier func;
identifier cfg;
@@
func(...,
- struct v4l2_subdev_pad_config *cfg
+ struct v4l2_subdev_state *sd_state
, ...)
{
<...
- cfg
+ sd_state
...>
}
// Change function declaration parameter
@@
identifier func;
identifier cfg;
type T;
@@
T func(...,
- struct v4l2_subdev_pad_config *cfg
+ struct v4l2_subdev_state *sd_state
, ...);
// Change function return value
@@
identifier func;
@@
- struct v4l2_subdev_pad_config
+ struct v4l2_subdev_state
*func(...)
{
...
}
// Change function declaration return value
@@
identifier func;
@@
- struct v4l2_subdev_pad_config
+ struct v4l2_subdev_state
*func(...);
// Some drivers pass a local pad_cfg for a single pad to a called function. Wrap it
// inside a pad_state.
@@
identifier func;
identifier pad_cfg;
@@
func(...)
{
...
struct v4l2_subdev_pad_config pad_cfg;
+ struct v4l2_subdev_state pad_state = { .pads = &pad_cfg };
<+...
(
v4l2_subdev_call
|
sensor_call
|
isi_try_fse
|
isc_try_fse
|
saa_call_all
)
(...,
- &pad_cfg
+ &pad_state
,...)
...+>
}
// If the function uses fields from pad_config, access via state->pads
@@
identifier func;
identifier state;
@@
func(...,
struct v4l2_subdev_state *state
, ...)
{
<...
(
- state->try_fmt
+ state->pads->try_fmt
|
- state->try_crop
+ state->pads->try_crop
|
- state->try_compose
+ state->pads->try_compose
)
...>
}
// If the function accesses the filehandle, use fh->state instead
@@
struct v4l2_subdev_fh *fh;
@@
- fh->pad
+ fh->state
@@
struct v4l2_subdev_fh fh;
@@
- fh.pad
+ fh.state
// Start of vsp1 specific
@@
@@
struct vsp1_entity {
...
- struct v4l2_subdev_pad_config *config;
+ struct v4l2_subdev_state *config;
...
};
@@
symbol entity;
@@
vsp1_entity_init(...)
{
...
entity->config =
- v4l2_subdev_alloc_pad_config
+ v4l2_subdev_alloc_state
(&entity->subdev);
...
}
@@
symbol entity;
@@
vsp1_entity_destroy(...)
{
...
- v4l2_subdev_free_pad_config
+ v4l2_subdev_free_state
(entity->config);
...
}
@exists@
identifier func =~ "(^vsp1.*)|(hsit_set_format)|(sru_enum_frame_size)|(sru_set_format)|(uif_get_selection)|(uif_set_selection)|(uds_enum_frame_size)|(uds_set_format)|(brx_set_format)|(brx_get_selection)|(histo_get_selection)|(histo_set_selection)|(brx_set_selection)";
symbol config;
@@
func(...) {
...
- struct v4l2_subdev_pad_config *config;
+ struct v4l2_subdev_state *config;
...
}
// End of vsp1 specific
// Start of rcar specific
@@
identifier sd;
identifier pad_cfg;
@@
rvin_try_format(...)
{
...
- struct v4l2_subdev_pad_config *pad_cfg;
+ struct v4l2_subdev_state *sd_state;
...
- pad_cfg = v4l2_subdev_alloc_pad_config(sd);
+ sd_state = v4l2_subdev_alloc_state(sd);
<...
- pad_cfg
+ sd_state
...>
- v4l2_subdev_free_pad_config(pad_cfg);
+ v4l2_subdev_free_state(sd_state);
...
}
// End of rcar specific
// Start of rockchip specific
@@
identifier func =~ "(rkisp1_rsz_get_pad_fmt)|(rkisp1_rsz_get_pad_crop)|(rkisp1_rsz_register)";
symbol rsz;
symbol pad_cfg;
@@
func(...)
{
+ struct v4l2_subdev_state state = { .pads = rsz->pad_cfg };
...
- rsz->pad_cfg
+ &state
...
}
@@
identifier func =~ "(rkisp1_isp_get_pad_fmt)|(rkisp1_isp_get_pad_crop)";
symbol isp;
symbol pad_cfg;
@@
func(...)
{
+ struct v4l2_subdev_state state = { .pads = isp->pad_cfg };
...
- isp->pad_cfg
+ &state
...
}
@@
symbol rkisp1;
symbol isp;
symbol pad_cfg;
@@
rkisp1_isp_register(...)
{
+ struct v4l2_subdev_state state = { .pads = rkisp1->isp.pad_cfg };
...
- rkisp1->isp.pad_cfg
+ &state
...
}
// End of rockchip specific
// Start of tegra-video specific
@@
identifier sd;
identifier pad_cfg;
@@
__tegra_channel_try_format(...)
{
...
- struct v4l2_subdev_pad_config *pad_cfg;
+ struct v4l2_subdev_state *sd_state;
...
- pad_cfg = v4l2_subdev_alloc_pad_config(sd);
+ sd_state = v4l2_subdev_alloc_state(sd);
<...
- pad_cfg
+ sd_state
...>
- v4l2_subdev_free_pad_config(pad_cfg);
+ v4l2_subdev_free_state(sd_state);
...
}
@@
identifier sd_state;
@@
__tegra_channel_try_format(...)
{
...
struct v4l2_subdev_state *sd_state;
<...
- sd_state->try_crop
+ sd_state->pads->try_crop
...>
}
// End of tegra-video specific
// </smpl>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The HEVC HANTRO driver needs to know the number of bits to skip at
the beginning of the slice header.
That is a hardware specific requirement so create a dedicated control
for this purpose.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Add decode params control and the associated structure to group
all the information that are needed to decode a reference frame as
is described in ITU-T Rec. H.265 section "8.3.2 Decoding process
for reference picture set".
Adapt Cedrus driver to these changes.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@collabora.com>
Reviewed-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Add fields and flags as they are defined in
7.4.3.3.1 "General picture parameter set RBSP semantics of the
H.265 ITU specification.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@collabora.com>
Reviewed-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
This is an NEC remote control device shipped with some Toshiba TVs.
Signed-off-by: Alexander Voronov <avv.0@ya.ru>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
sps_max_sub_layers_minus1 is needed if the driver wishes to determine
whether or not a frame might be used for reference.
Signed-off-by: John Cox <jc@kynesim.co.uk>
Reviewed-by: Benjamin Gaignard <benjamin.gaignard@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
On some platforms a video device can capture either video data or
metadata. The driver can implement vidioc functions for both video and
metadata, and use a single vb2_queue for the buffers. However, vb2_queue
requires choosing a single buffer type, which conflicts with the idea of
capturing either video or metadata.
The buffer type of vb2_queue can be changed, but it's not obvious how
this should be done in the drivers. To help this, add a new helper
function vb2_queue_change_type() which ensures the correct checks and
documents how it can be used.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Until now, the MPEG-2 V4L2 API was not exported as a public API,
and only defined in a private media header (media/mpeg2-ctrls.h).
After reviewing the MPEG-2 specification in detail, and reworking
the controls so they match the MPEG-2 semantics properly,
we can consider it ready.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Tested-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Jernej Skrabec <jernej.skrabec@siol.net>
Tested-by: Daniel Almeida <daniel.almeida@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Move the MPEG-2 stateless control types out of staging,
and re-number it to avoid any confusion.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Tested-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Jernej Skrabec <jernej.skrabec@siol.net>
Tested-by: Daniel Almeida <daniel.almeida@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The Hantro and Cedrus drivers work in frame-mode,
meaning they expect all the slices in a picture (either frame
or field structure) to be passed in each OUTPUT buffer.
These two are the only V4L2 MPEG-2 stateless decoders currently
supported. Given the VA-API drivers also work per-frame,
coalescing all the MPEG-2 slices in a buffer before the decoding
operation, it makes sense to not expect slice-mode drivers and
therefore remove V4L2_CID_MPEG_VIDEO_MPEG2_SLICE_PARAMS.
This is done to avoid carrying an unused interface. If needed,
this control can be added without breaking backwards compatibility.
Note that this would mean introducing a enumerator control to
specify the decoding mode (see V4L2_CID_STATELESS_H264_DECODE_MODE).
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Co-developed-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Signed-off-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Tested-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Jernej Skrabec <jernej.skrabec@siol.net>
Tested-by: Daniel Almeida <daniel.almeida@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The forward and backwards references are specified per-picture
and not per-slice. Move it to V4L2_CID_MPEG_VIDEO_MPEG2_PICTURE.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Tested-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Jernej Skrabec <jernej.skrabec@siol.net>
Tested-by: Daniel Almeida <daniel.almeida@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Typically, bitstreams are composed of a sequence header,
followed by a number of picture header and picture coding extension
headers. Each picture can be composed of a number of slices.
Let's split the MPEG-2 uAPI to follow these semantics more closely,
allowing more usage flexibility. Having these controls split up
allows applications to set a sequence control at the beginning
of a sequence, and then set a picture control for each frame.
While here add padding fields where needed, and document
the uAPI header thoroughly.
Note that the V4L2_CTRL_TYPE_{} defines had to be moved because
it clashes with existing ones. This is not really an issue
since they will be re-defined when the controls are moved
out of staging.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Tested-by: Jonas Karlman <jonas@kwiboo.se>
Tested-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Jernej Skrabec <jernej.skrabec@siol.net>
Tested-by: Daniel Almeida <daniel.almeida@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Our current MPEG-2 uAPI uses 1-byte fields for MPEG-2
boolean syntax elements. Clean these by adding a 'flags'
field and flag macro for each boolean syntax element.
A follow-up change will refactor this uAPI so we don't need
to add padding fields just yet.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Tested-by: Jonas Karlman <jonas@kwiboo.se>
Tested-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Jernej Skrabec <jernej.skrabec@siol.net>
Tested-by: Daniel Almeida <daniel.almeida@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
As stated in the MPEG-2 specification, section 6.3.7 "Quant matrix
extension":
Each quantisation matrix has a default set of values. When a
sequence_header_code is decoded all matrices shall be reset to
their default values. User defined matrices may be downloaded
and this can occur in a sequence_header() or in a
quant_matrix_extension().
The load_intra_quantiser_matrix syntax elements are transmitted
in the bitstream headers, signalling that a quantisation matrix
needs to be loaded and used for pictures transmitted afterwards
(until the matrices are reset).
This "load" semantics are implemented in the V4L2 interface
without the need of any "load" flags: passing the control
is effectively a load.
Therefore, rework the V4L2_CID_MPEG_VIDEO_MPEG2_QUANTISATION
semantics to match the MPEG-2 semantics. Quantisation matrices
values are now initialized by the V4L2 control core to their
reset default value, and applications are expected to reset
their values as specified.
The quantisation control is therefore optional, and used to
load bitstream-defined values in the quantisation matrices.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Co-developed-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Signed-off-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Tested-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Jernej Skrabec <jernej.skrabec@siol.net>
Tested-by: Daniel Almeida <daniel.almeida@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The MPEG-2 specification refers to the quantisation matrices
using the word "quantisation". Make the V4L2 interface more
ergonomic by matching the MPEG-2 spec.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Tested-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Jernej Skrabec <jernej.skrabec@siol.net>
Tested-by: Daniel Almeida <daniel.almeida@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The tango platform was removed, so the driver is no longer needed.
Cc: Marc Gonzalez <marc.w.gonzalez@free.fr>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Mans Rullgard <mans@mansr.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Dependent slice segment flag for PPS control is misnamed. It should have
"enabled" at the end. It only tells if this flag is present in slice
header or not and not the actual value.
Fix this by renaming the PPS flag and introduce another flag for slice
control which tells actual value.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
When controls are used together with the Request API, then for
each request a v4l2_ctrl_handler struct is allocated. This contains
the controls that can be set in a request. If a control is *not* set in
the request, then the value used in the most recent previous request
must be used, or the current value if it is not found in any outstanding
requests.
The framework tried to find such a previous request and it would set
the 'req' pointer in struct v4l2_ctrl_ref to the v4l2_ctrl_ref of the
control in such a previous request. So far, so good. However, when that
previous request was applied to the hardware, returned to userspace, and
then userspace would re-init or free that request, any 'ref' pointer in
still-queued requests would suddenly point to freed memory.
This was not noticed before since the drivers that use this expected
that each request would always have the controls set, so there was
never any need to find a control in older requests. This requirement
was relaxed, and now this bug surfaced.
It was also made worse by changeset
2fae4d6aab ("media: v4l2-ctrls: v4l2_ctrl_request_complete() should always set ref->req")
which increased the chance of this happening.
The use of the 'req' pointer in v4l2_ctrl_ref was very fragile, so
drop this entirely. Instead add a valid_p_req bool to indicate that
p_req contains a valid value for this control. And if it is false,
then just use the current value of the control.
Note that VIDIOC_G_EXT_CTRLS will always return -EACCES when attempting
to get a control from a request until the request is completed. And in
that case, all controls in the request will have the control value set
(i.e. valid_p_req is true). This means that the whole 'find the most
recent previous request containing a control' idea is pointless, and
the code can be simplified considerably.
The v4l2_g_ext_ctrls_common() function was refactored a bit to make
it more understandable. It also avoids updating volatile controls
in a completed request since that was already done when the request
was completed.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Fixes: 2fae4d6aab ("media: v4l2-ctrls: v4l2_ctrl_request_complete() should always set ref->req")
Fixes: 6fa6f831f0 ("media: v4l2-ctrls: add core request support")
Cc: <stable@vger.kernel.org> # for v5.9 and up
Tested-by: Alexandre Courbot <acourbot@chromium.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Add keymaps and bindings for the simple IR (NEC) remotes used with
the MeCool KII-Pro and MeCool KIII-Pro Android STB devices.
Tested-by: Drazen Spio <drazsp@gmail.com>
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Rename v4l2_async_register_subdev_sensor_common as
v4l2_async_register_subdev_sensor. This is a part of the effort to make
the long names present in V4L2 fwnode and async frameworks shorter.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Rename v4l2_async_notifier_parse_fwnode_sensor_common() as
v4l2_async_notifier_parse_fwnode_sensor() and make the function static, as
it's not used by a driver and maybe never will.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
It was always assumed that walking the media graph would require holding
the media_device graph_mutex but this was not documented nor checked for.
Add a lockdep check to graph walk init and iter, and document the need for
acquiring the graph_mutex.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The plane size needs to be PAGE_ALIGNED, so it is not possible to have
sizes bigger than MAX_INT - PAGE_SIZE.
We already check for overflows when that happen:
if (size < vb->planes[plane].length)
goto free;
But it is good to explicitly state our max allowed value, in order to
align with the driver expectations.
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
According to Rec. ITU-T T.872 (06/2012) 6.5.3
APP14 segment is for color encoding, it contains a transform flag, which
may have values of 0, 1 and 2 and are interpreted as follows:
0 - CMYK for images that are encoded with four components
- RGB for images that are encoded with three components
1 - An image encoded with three components using YCbCr colour encoding.
2 - An image encoded with four components using YCCK colour encoding.
This is used in imx-jpeg decoder, to distinguish between
YUV444 and RGB24.
Signed-off-by: Mirela Rabulea <mirela.rabulea@nxp.com>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Hans Verkuil
Yunfei Dong
Hyunwoo Kim
Lin Ma
Sakari Ailus
Alexander Stein
Sergey Senozhatsky
Paul Kocialkowski
Sean Young
Jernej Skrabec
Ján Čáni
Shuah Khan
Arnd Bergmann
Tomi Valkeinen
Benjamin Gaignard
Alexander Voronov
John Cox
Ezequiel Garcia
Jernej Skrabec
Linus Torvalds
Christian Hewitt
Stanimir Varbanov
Bhaskar Chowdhury
Ricardo Ribalda
Mirela Rabulea