Many laptops can be woken up from Suspend-to-Idle by touchpad. This is
also the default behavior on other OSes.
However, if touchpad and touchscreen contact to each other when lid is
closed, wakeup events can be triggered inadventertly.
So let's disable the wakeup by default, but enable the wakeup capability
so users can enable it at their own discretion.
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Fix following warnings caused by mismatch bewteen function parameters
and comments.
drivers/hid/i2c-hid/i2c-hid-core.c:331: warning: Function parameter or member 'data_len' not described in 'i2c_hid_set_or_send_report'
drivers/hid/i2c-hid/i2c-hid-core.c:331: warning: Excess function parameter 'len' description in 'i2c_hid_set_or_send_report'
Signed-off-by: Xiaofei Tan <tanxiaofei@huawei.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Adding printouts to the i2c_hid_probe() function shows that it takes
quite some time. It used to take about 70 ms, but after commit
eef4016243 ("HID: i2c-hid: Always sleep 60ms after I2C_HID_PWR_ON
commands") it takes about 190 ms. This is not tons of time but it's
not trivial. Because we haven't yet specified that we'd prefer
asynchronous probe for this driver then, if the driver is builtin to
the kernel, we'll wait for this driver to finish before we start
probes for more drivers. Let's set the flag to enable asynchronous
for this driver so that other drivers aren't blocked from probing
until we finish.
Since this driver can be configured as a module and modules are
always asynchronously probed this is quite a safe change and will
benefit anyone who has a reason to build this driver into the kernel
instead of using it as a module.
[jkosina@suse.cz: drop spurious whitespace addition]
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Before this commit i2c_hid_parse() consists of the following steps:
1. Send power on cmd
2. usleep_range(1000, 5000)
3. Send reset cmd
4. Wait for reset to complete (device interrupt, or msleep(100))
5. Send power on cmd
6. Try to read HID descriptor
Notice how there is an usleep_range(1000, 5000) after the first power-on
command, but not after the second power-on command.
Testing has shown that at least on the BMAX Y13 laptop's i2c-hid touchpad,
not having a delay after the second power-on command causes the HID
descriptor to read as all zeros.
In case we hit this on other devices too, the descriptor being all zeros
can be recognized by the following message being logged many, many times:
hid-generic 0018:0911:5288.0002: unknown main item tag 0x0
At the same time as the BMAX Y13's touchpad issue was debugged,
Kai-Heng was working on debugging some issues with Goodix i2c-hid
touchpads. It turns out that these need a delay after a PWR_ON command
too, otherwise they stop working after a suspend/resume cycle.
According to Goodix a delay of minimal 60ms is needed.
Having multiple cases where we need a delay after sending the power-on
command, seems to indicate that we should always sleep after the power-on
command.
This commit fixes the mentioned issues by moving the existing 1ms sleep to
the i2c_hid_set_power() function and changing it to a 60ms sleep.
Cc: stable@vger.kernel.org
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=208247
Reported-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Reported-and-tested-by: Andrea Borgia <andrea@borgia.bo.it>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Pull HID fixes from Jiri Kosina:
- linked list race condition fix in hid-steam driver from Rodrigo Rivas
Costa
- assorted deviceID-specific quirks and other small cosmetic cleanups
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/hid/hid:
HID: logitech-hidpp: avoid repeated "multiplier = " log messages
HID: logitech: Use HIDPP_RECEIVER_INDEX instead of 0xff
HID: quirks: Ignore Simply Automated UPB PIM
HID: apple: Disable Fn-key key-re-mapping on clone keyboards
MAINTAINERS: update uhid and hid-wiimote entry
HID: steam: fixes race in handling device list.
HID: magicmouse: do not set up autorepeat
HID: alps: support devices with report id 2
HID: quirks: Always poll Obins Anne Pro 2 keyboard
HID: i2c-hid: add Mediacom FlexBook edge13 to descriptor override
The Mediacom FlexBook edge13 uses the SIPODEV SP1064 touchpad, which does not
supply descriptors, so it has to be added to the override list.
Signed-off-by: Federico Ricchiuto <fed.ricchiuto@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Since commit 84af7a6194 ("checkpatch: kconfig: prefer 'help' over
'---help---'"), the number of '---help---' has been gradually
decreasing, but there are still more than 2400 instances.
This commit finishes the conversion. While I touched the lines,
I also fixed the indentation.
There are a variety of indentation styles found.
a) 4 spaces + '---help---'
b) 7 spaces + '---help---'
c) 8 spaces + '---help---'
d) 1 space + 1 tab + '---help---'
e) 1 tab + '---help---' (correct indentation)
f) 1 tab + 1 space + '---help---'
g) 1 tab + 2 spaces + '---help---'
In order to convert all of them to 1 tab + 'help', I ran the
following commend:
$ find . -name 'Kconfig*' | xargs sed -i 's/^[[:space:]]*---help---/\thelp/'
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
This device uses the SIPODEV SP1064 touchpad, which does not
supply descriptors, so it has to be added to the override list.
Cc: stable@vger.kernel.org
Signed-off-by: Julian Sax <jsbc@gmx.de>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
On the Dell XPS 9570, the Synaptics SYNA2393 touchpad generates spurious
interrupts after resuming from suspend until it receives some input or
is reset. Add it to the quirk I2C_HID_QUIRK_RESET_ON_RESUME so that it
is reset when resuming from suspend.
More information about the bug can be found in this mailing list
discussion: https://www.spinics.net/lists/linux-input/msg59530.html
Signed-off-by: Daniel Playfair Cal <daniel.playfair.cal@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The Surfbook E11B uses the SIPODEV SP1064 touchpad, which does not supply
descriptors, so it has to be added to the override list.
BugLink: https://bugs.launchpad.net/bugs/1858299
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Commit 52cf93e63e ("HID: i2c-hid: Don't reset device upon system
resume") fixes many touchpads and touchscreens, however ALPS touchpads
start to trigger IRQ storm after system resume.
Since it's total silence from ALPS, let's bring the old behavior back
to ALPS touchpads.
Fixes: 52cf93e63e ("HID: i2c-hid: Don't reset device upon system resume")
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
On some ThinkPad L390 some raydium 3118 touchscreen devices
doesn't response any data after reset, but some does.
Add this ID to no irq quirk,
then don't wait for any response alike on these touchscreens.
All kinds of raydium 3118 devices work fine.
BugLink: https://bugs.launchpad.net/bugs/1849721
Signed-off-by: Aaron Ma <aaron.ma@canonical.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This was introduced in commit 00b790ea54 ("HID: i2c-hid: Add a small
delay after sleep command for Raydium touchpanel") which has been
effectively reverted by commit 67b18dfb8c ("HID: i2c-hid: Remove
runtime power management").
Signed-off-by: You-Sheng Yang <vicamo.yang@canonical.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Before commit 67b18dfb8c ("HID: i2c-hid: Remove runtime power
management"), any i2c-hid touchscreens would typically be runtime-suspended
between the driver loading and Xorg or a Wayland compositor opening it,
causing it to be resumed again. This means that before this change,
we would call i2c_hid_set_power(OFF), i2c_hid_set_power(ON) before the
graphical session would start listening to the touchscreen.
It turns out that at least some SIS touchscreens, such as the one found
on the Asus T100HA, need a power-on command after reset, otherwise they
will not send any events.
Fixes: 67b18dfb8c ("HID: i2c-hid: Remove runtime power management")
Cc: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The Primebook C11B uses the SIPODEV SP1064 touchpad. There are 2 versions
of this 2-in-1 and the touchpad in the older version does not supply
descriptors, so it has to be added to the override list.
Cc: stable@vger.kernel.org
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Runtime power management in i2c-hid brings lots of issues, such as:
- When transitioning from display manager to desktop session, i2c-hid
was closed and opened, so the device was set to SLEEP and ON in a short
period. Vendors confirmed that their devices can't handle fast ON/SLEEP
command because Windows doesn't have this behavior.
- When rebooting, i2c-hid was closed, and the driver core put the device
back to full power before shutdown. This behavior also triggers a quick
SLEEP and ON commands that some devices can't handle, renders an
unusable touchpad after reboot.
- Most importantly, my power meter reports little to none energy saving
when i2c-hid is runtime suspended.
So let's remove runtime power management since there is no actual
benefit.
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
This 'SET_PWR_WAKEUP_DEV' quirk only works for weida's devices with pid
0xC300 & 0xC301. Some weida's devices with other pids also need this quirk
now. Use 'HID_ANY_ID' instead of 0xC300 to make all of weida's devices can be
fixed on the power on issue. This modification should be safe since devices
without power on issue will send the power on command only once.
Signed-off-by: HungNien Chen <hn.chen@weidahitech.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Pull HID fixes from Jiri Kosina:
- regression fixes (reverts) for module loading changes that turned out
to be incompatible with some userspace, from Benjamin Tissoires
- regression fix for special Logitech unifiying receiver 0xc52f, from
Hans de Goede
- a few device ID additions to logitech driver, from Hans de Goede
- fix for Bluetooth support on 2nd-gen Wacom Intuos Pro, from Jason
Gerecke
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/hid/hid:
HID: logitech-dj: Fix 064d:c52f receiver support
Revert "HID: core: Call request_module before doing device_add"
Revert "HID: core: Do not call request_module() in async context"
Revert "HID: Increase maximum report size allowed by hid_field_extract()"
HID: a4tech: fix horizontal scrolling
HID: hyperv: Add a module description line
HID: logitech-hidpp: Add support for the S510 remote control
HID: multitouch: handle faulty Elo touch device
HID: wacom: Sync INTUOSP2_BT touch state after each frame if necessary
HID: wacom: Correct button numbering 2nd-gen Intuos Pro over Bluetooth
HID: wacom: Send BTN_TOUCH in response to INTUOSP2_BT eraser contact
HID: wacom: Don't report anything prior to the tool entering range
HID: wacom: Don't set tool type until we're in range
HID: rmi: Use SET_REPORT request on control endpoint for Acer Switch 3 and 5
HID: logitech-hidpp: add support for the MX5500 keyboard
HID: logitech-dj: add support for the Logitech MX5500's Bluetooth Mini-Receiver
HID: i2c-hid: add iBall Aer3 to descriptor override
Add SPDX license identifiers to all Make/Kconfig files which:
- Have no license information of any form
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This device uses the SIPODEV SP1064 touchpad, which does not
supply descriptors, so it has to be added to the override
list.
BugLink: https://bugs.launchpad.net/bugs/1825718
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This reverts commit 74e7c6c877.
It finally turns out the touchpad is an engineering sample and it is
not the Synaptics touchpad. Let us revert this patch otherwise it will
affect the real Synaptics touchpad.
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
We have a new Dell laptop which has the synaptics I2C touchpad
(06cb:7e7e) on it. After booting up the Linux, the touchpad doesn't
work, there is no interrupt when touching the touchpad, after
disable the runtime PM, everything works well.
I also tried the quirk of I2C_HID_QUIRK_DELAY_AFTER_SLEEP, it is
better after applied this quirk, there are interrupts but data it
reports is invalid.
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
While using Elan touchpads, the message floods:
[ 136.138487] i2c_hid i2c-DELL08D6:00: i2c_hid_get_input: incomplete report (14/65535)
Though the message flood is annoying, the device it self works without
any issue. I suspect that the device in question takes too much time to
pull the IRQ back to high after I2C host has done reading its data.
Since the host receives all useful data, let's ignore the input report
when there's no data.
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
A Goodix touchpad doesn't work. Touching the touchpad can trigger IRQ
but there's no input event from HID subsystem.
Turns out it reports some invalid data:
[ 22.136630] i2c_hid i2c-DELL091F:00: input: 0b 00 01 00 00 00 00 00 00 00 00
After some trial and error, it's another device that doesn't work well
with ON/SLEEP commands. Disable runtime PM to fix the issue.
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The Odys Winbook 13 uses a SIPODEV SP1064 touchpad, which does not
supply descriptors, add this to the DMI descriptor override list, fixing
the touchpad not working.
BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1526312
Reported-by: Rene Wagner <redhatbugzilla@callerid.de>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
LG touchscreen (1fd2:8001) stops working after reboot:
[ 4.859153] i2c_hid i2c-SAPS2101:00: i2c_hid_get_input: incomplete report (64/66)
[ 4.936070] i2c_hid i2c-SAPS2101:00: i2c_hid_get_input: incomplete report (64/66)
[ 9.948224] i2c_hid i2c-SAPS2101:00: failed to reset device.
The device in question stops working after receives SLEEP, ON, SLEEP
commands in a short period. The scenario is like this:
- Once the desktop session closes, it also closed the hid device, so the
device gets runtime suspended and receives a SLEEP command.
- Before calling shutdown callback, it gets runtime resumed and received
an ON command.
- In the shutdown callback, it receives another SLEEP command.
I failed to find a reliable interval between ON/SLEEP commands that can
make it work, so let's simply disable runtime PM for the device.
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Pull in a merge commit that brought in 3b692c55e5 ("HID: asus: only
support backlight when it's not driven by WMI") so that fixup could be
applied on top of it.
This device uses the SIPODEV SP1064 touchpad, which does not
supply descriptors, so it has to be added to the override list.
Reported-by: Tim Aldridge <taldridge@mac.com>
Signed-off-by: Julian Sax <jsbc@gmx.de>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Commit 9ee3e06610 ("HID: i2c-hid: override HID descriptors for certain
devices") added a new dmi_system_id quirk table to override certain HID
report descriptors for some systems that lack them.
But the table wasn't properly terminated, causing the dmi matching to
walk off into la-la-land, and starting to treat random data as dmi
descriptor pointers, causing boot-time oopses if you were at all
unlucky.
Terminate the array.
We really should have some way to just statically check that arrays that
should be terminated by an empty entry actually are so. But the HID
people really should have caught this themselves, rather than have me
deal with an oops during the merge window. Tssk, tssk.
Cc: Julian Sax <jsbc@gmx.de>
Cc: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Cc: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Raydium touchpanel (2386:4B33) sometimes does not work in desktop session
although it works in display manager.
During user logging, the display manager exits, close the HID device,
then the device gets runtime suspended and powered off. The desktop
session begins shortly after, opens the HID device, then the device gets
runtime resumed and powered on.
If the trasition from display manager to desktop sesesion is fast, the
touchpanel cannot switch from powered off to powered on in short
timeframe. So add a small delay to workaround the issue.
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
A particular touchpad (SIPODEV SP1064) refuses to supply the HID
descriptors. This patch provides the framework for overriding these
descriptors based on DMI data. It also includes the descriptors for
said touchpad, which were extracted by listening to the traffic of the
windows filter driver, as well as the DMI data for the laptops known
to use this device.
Relevant Bug: https://bugzilla.redhat.com/show_bug.cgi?id=1526312
Cc: Hans de Goede <hdegoede@redhat.com>
Reported-and-tested-by: ahormann@gmx.net
Reported-and-tested-by: Bruno Jesus <bruno.fl.jesus@gmail.com>
Reported-and-tested-by: Dietrich <enaut.w@googlemail.com>
Reported-and-tested-by: kloxdami@yahoo.com
Signed-off-by: Julian Sax <jsbc@gmx.de>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Commit 52cf93e63e ("HID: i2c-hid: Don't reset device upon system resume")
removes the need for the RESEND_REPORT_DESCR quirk for Raydium devices, but
kept it for the SIS device id 10FB touchscreens, as the author of that
commit could not determine if the quirk is still necessary there.
I've tested suspend/resume on a Toshiba Click Mini L9W-B which is the
device for which this quirk was added in the first place and with the
"Don't reset device upon system resume" fix the quirk is no longer
necessary, so this commit removes it.
Note even better I also had some other devices with SIS touchscreens which
suspend/resume issues, where the RESEND_REPORT_DESCR quirk did not help.
I've also tested these devices with the "Don't reset device upon system
resume" fix and I'm happy to report that that fix also fixes touchscreen
resume on the following devices:
Asus T100HA
Asus T200TA
Peaq C1010
Cc: Kai-Heng Feng <kai.heng.feng@canonical.com>
Acked-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This hantick HTIX5288 touchpad can quickly fall in a wrong state if
there are too many open/close operations. This will either make it stop
reporting any input, or will shift all the input reads by a few bytes,
making it impossible to decode.
Here, we never release the probed touchpad runtime pm while the driver
is loaded, which should disable all runtime pm suspend/resumes.
This fast repetition of sleep/wakeup is also more likely to happen when
using runtime PM, which is why the quirk is done there, and not for all
power downs, which would include suspend or module removal.
Signed-off-by: Anisse Astier <anisse@astier.eu>
Cc: stable@vger.kernel.org
Acked-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: Philip Müller <philm@manjaro.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Raydium touchscreen triggers interrupt storm after system-wide suspend:
[ 179.085033] i2c_hid i2c-CUST0000:00: i2c_hid_get_input: incomplete report (58/65535)
According to Raydium, Windows driver does not reset the device after system
resume.
The HID over I2C spec does specify a reset should be used at intialization, but
it doesn't specify if reset is required for system suspend.
Tested this patch on other i2c-hid touchpanels I have and those touchpanels do
work after S3 without doing reset. If any regression happens to other
touchpanel vendors, we can use quirk for Raydium devices.
There's still one device uses I2C_HID_QUIRK_RESEND_REPORT_DESCR so keep it
there.
Cc: Aaron Ma <aaron.ma@canonical.com>
Cc: AceLan Kao <acelan.kao@canonical.com>
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Commit ac75a04104 ("HID: i2c-hid: fix size check and type usage") started
writing messages when the ret_size is <= 2 from i2c_master_recv. However, my
device i2c-DLL07D1 returns 2 for a short period of time (~0.5s) after I stop
moving the pointing stick or touchpad. It varies, but you get ~50 messages
each time which spams the log hard.
[ 95.925055] i2c_hid i2c-DLL07D1:01: i2c_hid_get_input: incomplete report (83/2)
This has also been observed with a i2c-ALP0017.
[ 1781.266353] i2c_hid i2c-ALP0017:00: i2c_hid_get_input: incomplete report (30/2)
Only print the message when ret_size is totally invalid and less than 2 to cut
down on the log spam.
Fixes: ac75a04104 ("HID: i2c-hid: fix size check and type usage")
Reported-by: John Smith <john-s-84@gmx.net>
Cc: stable@vger.kernel.org
Signed-off-by: Jason Andryuk <jandryuk@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Some wacom w9013 devices have a vddl supply for "low valtage"
requirements. Add support in this driver to turn on this low voltage
supply. We can also drop a handful of error messages because the
regulator core is already printing an error when bulk regulators fail to
enable or disable.
Cc: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Dmitry Torokhov <dtor@chromium.org>
Cc: Doug Anderson <dianders@chromium.org>
Acked-by: Rob Herring <robh@kernel.org>
Cc: <devicetree@vger.kernel.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Acked-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Use devm here to save some lines and prepare for bulk regulator usage in
this driver. Otherwise, when we devm bulk get regulators we'll free the
containing i2c_hid structure and try to put regulator pointers from
freed memory.
Cc: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Dmitry Torokhov <dtor@chromium.org>
Cc: Doug Anderson <dianders@chromium.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Acked-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Since commit 85ae911331 ("HID: i2c-hid: remove custom locking from
i2c_hid_open/close") there are no more users of i2c_hid_open_mut.
Remove the unused mutex.
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Jiri Kosina <jikos@kernel.org>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Reviewed-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
On many Chromebooks touch devices are multi-sourced; the components are
electrically compatible and one can be freely swapped for another without
changing the OS image or firmware.
To avoid bunch of scary messages when device is not actually present in the
system let's try testing basic communication with it and if there is no
response terminate probe early with -ENXIO.
Signed-off-by: Dmitry Torokhov <dtor@chromium.org>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The 0457:10fb touchscreen found on the Toshiba Click Mini L9W-B needs
to have a report-decriptors command send to it on resume in order for
the touchscreen to start generating events again on resume.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
i2c_hid_command() returns non-zero in error cases (the actual
errno). Error handling in for I2C_HID_QUIRK_RESEND_REPORT_DESCR
case in i2c_hid_resume() had the check inverted; fix that.
Fixes: 3e83eda467 ("HID: i2c-hid: Fix resume issue on Raydium touchscreen device")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Jiri Kosina
Kai-Heng Feng
Xiaofei Tan
Douglas Anderson
Hans de Goede
Linus Torvalds
Federico Ricchiuto
Masahiro Yamada
Julian Sax
Daniel Playfair Cal
Pavel Balan
Aaron Ma
You-Sheng Yang
HungNien Chen
Thomas Gleixner
Hui Wang
Anisse Astier
AceLan Kao
Jason Andryuk
Stephen Boyd
Sebastian Andrzej Siewior
Dmitry Torokhov