The build failure was introduced by
13dd0c9 (USB: otg/ulpi: extend the generic ulpi driver.)
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Cc: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The mx3fb driver needs the clock the IPU runs in order to calculate
the divider for the LCD clock. This patch adds the clock rate calculation
routine for the i.MX35 CPU.
Signed-off-by: Juergen Beisert <jbe@pengutronix.de>
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
According to the Datasheet:
"i.MX35 (MCIMX35) Multimedia Applications Processor Reference Manual,
Rev. 2" "Figure 14-24. Clock Control And Gating"
change the result of get_rate_ahb based on the frequency returned
by get_rate_arm to calculate the proper rate.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
According to the Datasheet:
"i.MX35 (MCIMX35) Multimedia Applications Processor Reference Manual,
Rev. 2" "Table 14-6. PDR0 Field Descriptions" the divider is
CCM_PER_AHB[3:0] + 1.
This patch adds the missing + 1.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
In the v2 reference manual there are no dividers combined of two
dividers. Instead, all dividers are simple 6bit dividers. I assume
the combined dividers only exist in preliminary hardware.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
If a watchdog reset occurs after booting in internal boot mode, the i.MX35
won't boot anymore. The boot ROM code seems to assume that some clocks are
turned on (they are after a power-on reset). This patch turns on the
necessary clocks.
Signed-off-by: Hans J. Koch <hjk@linutronix.de>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reported-by: John Ogness <jogness@linutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Last change I did made a big mess in function names and CONFIG names,
this patch fixes this so that the baseboard support is really built
when selected.
Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
* git://git.infradead.org/mtd-2.6:
mtd/nand_ids: Fix buswidth
mtd/m25p80: fix test for end of loop
mtd/m25p80: retlen is never NULL
MIPS: Fix gen_nand probe structures contents
gen_nand: Test if nr_chips field is valid
BFIN: Fix gen_nand probe structures contents
nand/denali: move all hardware initialization work to denali_hw_init
nand/denali: Add a page check in denali_read_page & denali_read_page_raw
nand/denali: use cpu_relax() while waiting for hardware interrupt
nand/denali: change read_status function method
nand/denali: Fixed check patch warnings
ARM: Fix gen_nand probe structures contents
mtd/nand_base: fix kernel-doc warnings & typos
nand/denali: use dev_xx debug function to replace nand_dbg_print and some printk
nand/denali: Fixed handle ECC error bugs
nand/denali: use iowrite32() to replace denali_write32()
nand/denali: Fixed probe function bugs
These three platforms didn't properly fill nr_chips in gen_nand
registration and therefore depended on gen_nand bug fixed by commit
81cbb0b177 ("mtd: gen_nand: fix support for
multiple chips")
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
1) Introduce ulpi specific flags for control of the ulpi phy
2) Extend the generic ulpi driver with support for Function and
Interface control of upli phy
3) Update the platforms using the generic ulpi driver with new ulpi
flags
4) Remove the otg control flags not in use
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The commit 9a763bf "get rid of mxc_gpio_init" changed gpio_init
and irq_init sequence. Usually we will call set_irq_chained_handler
in gpio_init functions, this should be called after the irq_init
called, otherwise the chained irq can't get propoer irq_chip and this
irq will remain masked even we called set_irq_chained_handler.
Signed-off-by: Jason Wang <jason77.wang@gmail.com>
Tested-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
as per suggested by Sascha
Signed-off-by: Eric Bénard <eric@eukrea.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This patch fixes the following Kconfig warning :
"arch/arm/mach-mx25/Kconfig:18:warning: choice value used outside its
choice group
Signed-off-by: Eric Bénard <eric@eukrea.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
In order to make this patch compile, even if the flexcan driver with
it's header defining the platform data isn't merged yet, two ifdefs have
been added. They effect that the "imx_add_flexcan" function results in a
no-op function if the driver hasn't been activated.
These ifdefs can be removed after the flexcan driver has been merged.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Because we add a 3ds debug board support in mxc level, we remove
those redundant codes from board level.
Signed-off-by: Jason Wang <jason77.wang@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
There are some more conflicts than detected by git, namely support for
the newly added cpuimx machines needed to be converted to dynamic device
registration.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Conflicts:
arch/arm/mach-imx/Makefile
arch/arm/mach-imx/devices.c
arch/arm/mach-imx/devices.h
arch/arm/mach-imx/eukrea_mbimx27-baseboard.c
arch/arm/mach-mx2/Kconfig
arch/arm/mach-mx25/Makefile
arch/arm/mach-mx25/devices.c
arch/arm/plat-mxc/include/mach/mx25.h
arch/arm/plat-mxc/include/mach/mxc_nand.h
without this patch, ipu_clk's value is 0 thus preventing mx3fb from
calculating the right divisor for pixel clock generator.
Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Like this one (if CONFIG_USB_ULPI is not set):
arch/arm/mach-mx3/mach-pcm043.c:312: warning: 'otg_pdata' defined but not used
arch/arm/mach-mx3/mach-pcm043.c:317: warning: 'usbh1_pdata' defined but not used
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
moboard_uart0_init requests a gpio. Without an exit function that
frees that gpio again binding the uart a second time doesn't work.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
As the kernel contains a copy of the GPL anyhow just get rid of the address
specification instead of fixing it.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
This function is defined once for each imx family and so is in the way
when compiling a kernel for more than one SoC.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Add two RGB led on mx31moboard using MC13783 led subsystem
Signed-off-by: Philippe Rétornaz <philippe.retornaz@epfl.ch>
Signed-off-by: Richard Purdie <rpurdie@linux.intel.com>
CC arch/arm/mach-mx3/mach-pcm037.o
arch/arm/mach-mx3/mach-pcm037.c: In function 'mxc_board_init':
arch/arm/mach-mx3/mach-pcm037.c:584: warning: unused variable 'tmp'
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This patch adds also the pin definition helpers in iomux-mx3.h
Signed-off-by: Alberto Panizzo <maramaopercheseimorto@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The member "clock" of struct "sja1000_platform_data" is documented as
"CAN bus oscillator frequency in Hz" but it's actually used as the CAN
clock frequency, which is half of it. To avoid further confusion, this
patch fixes it by renaming the member to "osc_freq". That way, also
non mainline users will notice the change. The platform code for the
relevant boards is updated accordingly. Furthermore, pre-defined
values are now used for the members "ocr" and "cdr".
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Russell King
Uwe Kleine-König
Juergen Beisert
Marc Kleine-Budde
Sascha Hauer
Hans J. Koch
Eric Bénard
Linus Torvalds
Marek Vasut
Igor Grinberg
Jason Wang
Fabio Estevam
Wolfram Sang
Daniel Mack
Philippe Rétornaz
Alberto Panizzo
Wolfgang Grandegger