During an eeh event when the cxl card is fenced and card sysfs attr
perst_reloads_same_image is set following warning message is seen in the
kernel logs:
Adapter context unlocked with 0 active contexts
------------[ cut here ]------------
WARNING: CPU: 12 PID: 627 at
../drivers/misc/cxl/main.c:325 cxl_adapter_context_unlock+0x60/0x80 [cxl]
Even though this warning is harmless, it clutters the kernel log
during an eeh event. This warning is triggered as the EEH callback
cxl_pci_error_detected doesn't obtain a context-lock before forcibly
detaching all active context and when context-lock is released during
call to cxl_configure_adapter from cxl_pci_slot_reset, a warning in
cxl_adapter_context_unlock is triggered.
To fix this warning, we acquire the adapter context-lock via
cxl_adapter_context_lock() in the eeh callback
cxl_pci_error_detected() once all the virtual AFU PHBs are notified
and their contexts detached. The context-lock is released in
cxl_pci_slot_reset() after the adapter is successfully reconfigured
and before the we call the slot_reset callback on slice attached
device-drivers.
Fixes: 70b565bbdb ("cxl: Prevent adapter reset if an active context exists")
Cc: stable@vger.kernel.org # v4.9+
Reported-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Signed-off-by: Vaibhav Jain <vaibhav@linux.vnet.ibm.com>
Acked-by: Frederic Barrat <fbarrat@linux.vnet.ibm.com>
Reviewed-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Tested-by: Uma Krishnan <ukrishn@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Add support for future IBM Coherent Accelerator (CXL) devices
with an IDs of 0x0623 and 0x0628.
Signed-off-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Signed-off-by: Uma Krishnan <ukrishn@linux.vnet.ibm.com>
Acked-by: Frederic Barrat <fbarrat@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The new Coherent Accelerator Interface Architecture, level 2, for the
IBM POWER9 brings new content and features:
- POWER9 Service Layer
- Registers
- Radix mode
- Process element entry
- Dedicated-Shared Process Programming Model
- Translation Fault Handling
- CAPP
- Memory Context ID
If a valid mm_struct is found the memory context id is used for each
transaction associated with the process handle. The PSL uses the
context ID to find the corresponding process element.
Signed-off-by: Christophe Lombard <clombard@linux.vnet.ibm.com>
Acked-by: Frederic Barrat <fbarrat@linux.vnet.ibm.com>
[mpe: Fixup comment formatting, unsplit long strings]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Point out the specific Coherent Accelerator Interface Architecture,
level 1, registers.
Code and functions specific to PSL8 (CAIA1) must be framed.
Signed-off-by: Christophe Lombard <clombard@linux.vnet.ibm.com>
Acked-by: Frederic Barrat <fbarrat@linux.vnet.ibm.com>
[mpe: Don't split long strings, it makes them hard to grep for]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Rename a few functions, changing the '_psl' suffix to '_psl8', to make
clear that the implementation is psl8 specific.
Those functions will have an equivalent implementation for the psl9 in
a later patch.
Signed-off-by: Christophe Lombard <clombard@linux.vnet.ibm.com>
Reviewed-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Acked-by: Frederic Barrat <fbarrat@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The service layer API (in cxl.h) lists some low-level functions whose
implementation is different on PSL8, PSL9 and XSL:
- Init implementation for the adapter and the afu.
- Invalidate TLB/SLB.
- Attach process for dedicated/directed models.
- Handle psl interrupts.
- Debug registers for the adapter and the afu.
- Traces.
Each environment implements its own functions, and the common code uses
them through function pointers, defined in cxl_service_layer_ops.
Signed-off-by: Christophe Lombard <clombard@linux.vnet.ibm.com>
Reviewed-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Acked-by: Frederic Barrat <fbarrat@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The mm_struct corresponding to the current task is acquired each time
an interrupt is raised. So to simplify the code, we only get the
mm_struct when attaching an AFU context to the process.
The mm_count reference is increased to ensure that the mm_struct can't
be freed. The mm_struct will be released when the context is detached.
A reference on mm_users is not kept to avoid a circular dependency if
the process mmaps its cxl mmio and forget to unmap before exiting.
The field glpid (pid of the group leader associated with the pid), of
the structure cxl_context, is removed because it's no longer useful.
Signed-off-by: Christophe Lombard <clombard@linux.vnet.ibm.com>
Reviewed-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Acked-by: Frederic Barrat <fbarrat@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The two previously fields pid and tid, located in the structure
cxl_irq_info, are only used in the guest environment. To avoid confusion,
it's not necessary to fill the fields in the bare-metal environment.
Pid_tid is now renamed to 'reserved' to avoid undefined behavior on
bare-metal. The PSL Process and Thread Identification Register
(CXL_PSL_PID_TID_An) is only used when attaching a dedicated process
for PSL8 only. This register goes away in CAIA2.
Signed-off-by: Christophe Lombard <clombard@linux.vnet.ibm.com>
Reviewed-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Acked-by: Frederic Barrat <fbarrat@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This bit is used to cause a flash image load for programmable
CAIA-compliant implementation. If this bit is set to ‘0’, a power
cycle of the adapter is required to load a programmable CAIA-com-
pliant implementation from flash.
This field will be used by the following patches.
Signed-off-by: Christophe Lombard <clombard@linux.vnet.ibm.com>
Reviewed-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Acked-by: Frederic Barrat <fbarrat@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This patch fix some spelling typos found in printk.
[jkosina@suse.cz: drop arch/arm64/kernel/hibernate.c that was already
in place]
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Fix a boundary condition where in some cases an eeh event with state ==
pci_channel_io_perm_failure wont be passed on to a driver attached to
the virtual PCI device associated with a slice. This will happen in case
the slice just before (n-1) doesn't have any vPHB bus associated with
it, that results in an early return from cxl_pci_error_detected()
callback.
With state == pci_channel_io_perm_failure, the adapter will be removed
irrespective of the return value of cxl_vphb_error_detected(). So we now
always return PCI_ERS_RESULT_DISCONNECTED for this case i.e even if
the AFU isn't using a vPHB (currently returns PCI_ERS_RESULT_NONE).
Fixes: e4f5fc001a6("cxl: Do not create vPHB if there are no AFU configuration records")
Signed-off-by: Vaibhav Jain <vaibhav@linux.vnet.ibm.com>
Reviewed-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Reviewed-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Acked-by: Frederic Barrat <fbarrat@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
But first update usage sites with the new header dependency.
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Fix up affected files that include this signal functionality via sched.h.
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
We are going to split <linux/sched/mm.h> out of <linux/sched.h>, which
will have to be picked up from other headers and a couple of .c files.
Create a trivial placeholder <linux/sched/mm.h> file that just
maps to <linux/sched.h> to make this patch obviously correct and
bisectable.
The APIs that are going to be moved first are:
mm_alloc()
__mmdrop()
mmdrop()
mmdrop_async_fn()
mmdrop_async()
mmget_not_zero()
mmput()
mmput_async()
get_task_mm()
mm_access()
mm_release()
Include the new header in the files that are going to need it.
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
We are going to split <linux/sched/clock.h> out of <linux/sched.h>, which
will have to be picked up from other headers and .c files.
Create a trivial placeholder <linux/sched/clock.h> file that just
maps to <linux/sched.h> to make this patch obviously correct and
bisectable.
Include the new header in the files that are going to need it.
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Highlights include:
- An update of the disassembly code used by xmon to the latest versions in
binutils. We've received permission from all the authors of the relevant
binutils changes to relicense their changes to the relevant files from GPLv3
to GPLv2, for inclusion in Linux. Thanks to Peter Bergner for doing the leg
work to get permission from everyone.
- Addition of the "architected" Power9 CPU table entry, allowing us to boot
in Power9 architected mode under a hypervisor.
- Updates to the Power9 PMU code.
- Implementation of clear_bit_unlock_is_negative_byte() to optimise
unlock_page().
- Freescale updates from Scott: "Highlights include 8xx breakpoints and perf,
t1042rdb display support, and board updates."
Thanks to:
Al Viro, Andrew Donnellan, Aneesh Kumar K.V, Balbir Singh, Douglas Miller,
Frédéric Weisbecker, Gavin Shan, Madhavan Srinivasan, Michael Roth, Nathan
Fontenot, Naveen N. Rao, Nicholas Piggin, Peter Bergner, Paul E. McKenney,
Rashmica Gupta, Russell Currey, Sahil Mehta, Stewart Smith.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=rspd
-----END PGP SIGNATURE-----
Merge tag 'powerpc-4.11-2' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull more powerpc updates from Michael Ellerman:
"Highlights include:
- an update of the disassembly code used by xmon to the latest
versions in binutils. We've received permission from all the
authors of the relevant binutils changes to relicense their changes
to the relevant files from GPLv3 to GPLv2, for inclusion in Linux.
Thanks to Peter Bergner for doing the leg work to get permission
from everyone.
- addition of the "architected" Power9 CPU table entry, allowing us
to boot in Power9 architected mode under a hypervisor.
- updates to the Power9 PMU code.
- implementation of clear_bit_unlock_is_negative_byte() to optimise
unlock_page().
- Freescale updates from Scott: "Highlights include 8xx breakpoints
and perf, t1042rdb display support, and board updates."
Thanks to:
Al Viro, Andrew Donnellan, Aneesh Kumar K.V, Balbir Singh, Douglas
Miller, Frédéric Weisbecker, Gavin Shan, Madhavan Srinivasan,
Michael Roth, Nathan Fontenot, Naveen N. Rao, Nicholas Piggin, Peter
Bergner, Paul E. McKenney, Rashmica Gupta, Russell Currey, Sahil
Mehta, Stewart Smith"
* tag 'powerpc-4.11-2' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (48 commits)
powerpc: Remove leftover cputime_to_nsecs call causing build error
powerpc/mm/hash: Always clear UPRT and Host Radix bits when setting up CPU
powerpc/optprobes: Fix TOC handling in optprobes trampoline
powerpc/pseries: Advertise Hot Plug Event support to firmware
cxl: fix nested locking hang during EEH hotplug
powerpc/xmon: Dump memory in CPU endian format
powerpc/pseries: Revert 'Auto-online hotplugged memory'
powerpc/powernv: Make PCI non-optional
powerpc/64: Implement clear_bit_unlock_is_negative_byte()
powerpc/powernv: Remove unused variable in pnv_pci_sriov_disable()
powerpc/kernel: Remove error message in pcibios_setup_phb_resources()
powerpc/mm: Fix typo in set_pte_at()
pci/hotplug/pnv-php: Disable MSI and PCI device properly
pci/hotplug/pnv-php: Disable surprise hotplug capability on conflicts
pci/hotplug/pnv-php: Remove WARN_ON() in pnv_php_put_slot()
powerpc: Add POWER9 architected mode to cputable
powerpc/perf: use is_kernel_addr macro in perf_get_misc_flags()
powerpc/perf: Avoid FAB_*_MATCH checks for power9
powerpc/perf: Add restrictions to PMC5 in power9 DD1
powerpc/perf: Use Instruction Counter value
...
->fault(), ->page_mkwrite(), and ->pfn_mkwrite() calls do not need to
take a vma and vmf parameter when the vma already resides in vmf.
Remove the vma parameter to simplify things.
[arnd@arndb.de: fix ARM build]
Link: http://lkml.kernel.org/r/20170125223558.1451224-1-arnd@arndb.de
Link: http://lkml.kernel.org/r/148521301778.19116.10840599906674778980.stgit@djiang5-desk3.ch.intel.com
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Ross Zwisler <ross.zwisler@linux.intel.com>
Cc: Theodore Ts'o <tytso@mit.edu>
Cc: Darrick J. Wong <darrick.wong@oracle.com>
Cc: Matthew Wilcox <mawilcox@microsoft.com>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Jan Kara <jack@suse.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit 14a3ae34bf ("cxl: Prevent read/write to AFU config space while AFU
not configured") introduced a rwsem to fix an invalid memory access that
occurred when someone attempts to access the config space of an AFU on a
vPHB whilst the AFU is deconfigured, such as during EEH recovery.
It turns out that it's possible to run into a nested locking issue when EEH
recovery fails and a full device hotplug is required.
cxl_pci_error_detected() deconfigures the AFU, taking a writer lock on
configured_rwsem. When EEH recovery fails, the EEH code calls
pci_hp_remove_devices() to remove the device, which in turn calls
cxl_remove() -> cxl_pci_remove_afu() -> pci_deconfigure_afu(), which tries
to grab the writer lock that's already held.
Standard rwsem semantics don't express what we really want to do here and
don't allow for nested locking. Fix this by replacing the rwsem with an
atomic_t which we can control more finely. Allow the AFU to be locked
multiple times so long as there are no readers.
Fixes: 14a3ae34bf ("cxl: Prevent read/write to AFU config space while AFU not configured")
Cc: stable@vger.kernel.org # v4.9+
Signed-off-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Acked-by: Frederic Barrat <fbarrat@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Stub out the debugfs functions so that the build doesn't break when
CONFIG_DEBUG_FS=n.
Reported-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Acked-by: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
During EEH recovery, we deconfigure all AFUs whilst leaving the
corresponding vPHB and virtual PCI device in place.
If something attempts to interact with the AFU's PCI config space (e.g.
running lspci) after the AFU has been deconfigured and before it's
reconfigured, cxl_pcie_{read,write}_config() will read invalid values from
the deconfigured struct cxl_afu and proceed to Oops when they try to
dereference pointers that have been set to NULL during deconfiguration.
Add a rwsem to struct cxl_afu so we can prevent interaction with config
space while the AFU is deconfigured.
Reported-by: Pradipta Ghosh <pradghos@in.ibm.com>
Suggested-by: Frederic Barrat <fbarrat@linux.vnet.ibm.com>
Cc: stable@vger.kernel.org # v4.9+
Signed-off-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Signed-off-by: Vaibhav Jain <vaibhav@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This change adds a force psl data cache flush during device shutdown
callback. This should reduce a possibility of psl holding a dirty
cache line while the CAPP is being reinitialized, which may result in
a UE [load/store] machine check error.
Signed-off-by: Vaibhav Jain <vaibhav@linux.vnet.ibm.com>
Reviewed-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Acked-by: Frederic Barrat <fbarrat@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The kernel API does not use anything from this header file.
Signed-off-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Acked-by: Frederic Barrat <fbarrat@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Highlights include:
- Support for the kexec_file_load() syscall, which is a prereq for secure and
trusted boot.
- Prevent kernel execution of userspace on P9 Radix (similar to SMEP/PXN).
- Sort the exception tables at build time, to save time at boot, and store
them as relative offsets to save space in the kernel image & memory.
- Allow building the kernel with thin archives, which should allow us to build
an allyesconfig once some other fixes land.
- Build fixes to allow us to correctly rebuild when changing the kernel endian
from big to little or vice versa.
- Plumbing so that we can avoid doing a full mm TLB flush on P9 Radix.
- Initial stack protector support (-fstack-protector).
- Support for dumping the radix (aka. Linux) and hash page tables via debugfs.
- Fix an oops in cxl coredump generation when cxl_get_fd() is used.
- Freescale updates from Scott: "Highlights include 8xx hugepage support,
qbman fixes/cleanup, device tree updates, and some misc cleanup."
- Many and varied fixes and minor enhancements as always.
Thanks to:
Alexey Kardashevskiy, Andrew Donnellan, Aneesh Kumar K.V, Anshuman Khandual,
Anton Blanchard, Balbir Singh, Bartlomiej Zolnierkiewicz, Christophe Jaillet,
Christophe Leroy, Denis Kirjanov, Elimar Riesebieter, Frederic Barrat,
Gautham R. Shenoy, Geliang Tang, Geoff Levand, Jack Miller, Johan Hovold,
Lars-Peter Clausen, Libin, Madhavan Srinivasan, Michael Neuling, Nathan
Fontenot, Naveen N. Rao, Nicholas Piggin, Pan Xinhui, Peter Senna Tschudin,
Rashmica Gupta, Rui Teng, Russell Currey, Scott Wood, Simon Guo, Suraj
Jitindar Singh, Thiago Jung Bauermann, Tobias Klauser, Vaibhav Jain.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=xOzf
-----END PGP SIGNATURE-----
Merge tag 'powerpc-4.10-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc updates from Michael Ellerman:
"Highlights include:
- Support for the kexec_file_load() syscall, which is a prereq for
secure and trusted boot.
- Prevent kernel execution of userspace on P9 Radix (similar to
SMEP/PXN).
- Sort the exception tables at build time, to save time at boot, and
store them as relative offsets to save space in the kernel image &
memory.
- Allow building the kernel with thin archives, which should allow us
to build an allyesconfig once some other fixes land.
- Build fixes to allow us to correctly rebuild when changing the
kernel endian from big to little or vice versa.
- Plumbing so that we can avoid doing a full mm TLB flush on P9
Radix.
- Initial stack protector support (-fstack-protector).
- Support for dumping the radix (aka. Linux) and hash page tables via
debugfs.
- Fix an oops in cxl coredump generation when cxl_get_fd() is used.
- Freescale updates from Scott: "Highlights include 8xx hugepage
support, qbman fixes/cleanup, device tree updates, and some misc
cleanup."
- Many and varied fixes and minor enhancements as always.
Thanks to:
Alexey Kardashevskiy, Andrew Donnellan, Aneesh Kumar K.V, Anshuman
Khandual, Anton Blanchard, Balbir Singh, Bartlomiej Zolnierkiewicz,
Christophe Jaillet, Christophe Leroy, Denis Kirjanov, Elimar
Riesebieter, Frederic Barrat, Gautham R. Shenoy, Geliang Tang, Geoff
Levand, Jack Miller, Johan Hovold, Lars-Peter Clausen, Libin,
Madhavan Srinivasan, Michael Neuling, Nathan Fontenot, Naveen N.
Rao, Nicholas Piggin, Pan Xinhui, Peter Senna Tschudin, Rashmica
Gupta, Rui Teng, Russell Currey, Scott Wood, Simon Guo, Suraj
Jitindar Singh, Thiago Jung Bauermann, Tobias Klauser, Vaibhav Jain"
[ And thanks to Michael, who took time off from a new baby to get this
pull request done. - Linus ]
* tag 'powerpc-4.10-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (174 commits)
powerpc/fsl/dts: add FMan node for t1042d4rdb
powerpc/fsl/dts: add sg_2500_aqr105_phy4 alias on t1024rdb
powerpc/fsl/dts: add QMan and BMan nodes on t1024
powerpc/fsl/dts: add QMan and BMan nodes on t1023
soc/fsl/qman: test: use DEFINE_SPINLOCK()
powerpc/fsl-lbc: use DEFINE_SPINLOCK()
powerpc/8xx: Implement support of hugepages
powerpc: get hugetlbpage handling more generic
powerpc: port 64 bits pgtable_cache to 32 bits
powerpc/boot: Request no dynamic linker for boot wrapper
soc/fsl/bman: Use resource_size instead of computation
soc/fsl/qe: use builtin_platform_driver
powerpc/fsl_pmc: use builtin_platform_driver
powerpc/83xx/suspend: use builtin_platform_driver
powerpc/ftrace: Fix the comments for ftrace_modify_code
powerpc/perf: macros for power9 format encoding
powerpc/perf: power9 raw event format encoding
powerpc/perf: update attribute_group data structure
powerpc/perf: factor out the event format field
powerpc/mm/iommu, vfio/spapr: Put pages on VFIO container shutdown
...
Every single user of vmf->virtual_address typed that entry to unsigned
long before doing anything with it so the type of virtual_address does
not really provide us any additional safety. Just use masked
vmf->address which already has the appropriate type.
Link: http://lkml.kernel.org/r/1479460644-25076-3-git-send-email-jack@suse.cz
Signed-off-by: Jan Kara <jack@suse.cz>
Acked-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Ross Zwisler <ross.zwisler@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Drop duplicate header sched.h from native.c.
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Reviewed-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Fix the following coccinelle warnings:
drivers/misc/cxl/debugfs.c:46:0-23: WARNING: fops_io_x64 should be
defined with DEFINE_DEBUGFS_ATTRIBUTE
drivers/misc/cxl/guest.c:890:5-26: WARNING: Comparison to bool
drivers/misc/cxl/irq.c:107:3-23: WARNING: Assignment of bool to 0/1
drivers/misc/cxl/native.c:57:2-3: Unneeded semicolon
drivers/misc/cxl/native.c:170:2-3: Unneeded semicolon
Signed-off-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Acked-by: Frederic Barrat <fbarrat@linux.vnet.ibm.com>
Reviewed-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Acked-by: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
If a process dumps core while owning a cxl file descriptor obtained
from an AFU driver (e.g. cxlflash) through the cxl_get_fd() API, the
following error occurs:
[ 868.027591] Unable to handle kernel paging request for data at address ...
[ 868.027778] Faulting instruction address: 0xc00000000035edb0
cpu 0x8c: Vector: 300 (Data Access) at [c000003c688275e0]
pc: c00000000035edb0: elf_core_dump+0xd60/0x1300
lr: c00000000035ed80: elf_core_dump+0xd30/0x1300
sp: c000003c68827860
msr: 9000000100009033
dar: c
dsisr: 40000000
current = 0xc000003c68780000
paca = 0xc000000001b73200 softe: 0 irq_happened: 0x01
pid = 46725, comm = hxesurelock
enter ? for help
[c000003c68827a60] c00000000036948c do_coredump+0xcec/0x11e0
[c000003c68827c20] c0000000000ce9e0 get_signal+0x540/0x7b0
[c000003c68827d10] c000000000017354 do_signal+0x54/0x2b0
[c000003c68827e00] c00000000001777c do_notify_resume+0xbc/0xd0
[c000003c68827e30] c000000000009838 ret_from_except_lite+0x64/0x68
--- Exception: 300 (Data Access) at 00003fff98ad2918
The root cause is that the address_space structure for the file
doesn't define a 'host' member.
When cxl allocates a file descriptor, it's using the anonymous inode
to back the file, but allocates a private address_space for each
context. The private address_space allows to track memory allocation
for each context. cxl doesn't define the 'host' member of the address
space, i.e. the inode. We don't want to define it as the anonymous
inode, since there's no longer a 1-to-1 relation between address_space
and inode.
To fix it, instead of using the anonymous inode, we introduce a simple
pseudo filesystem so that cxl can allocate its own inodes. So we now
have one inode for each file and address_space. The pseudo filesystem
is only mounted on the first allocation of a file descriptor by
cxl_get_fd().
Tested with cxlflash.
Signed-off-by: Frederic Barrat <fbarrat@linux.vnet.ibm.com>
Reviewed-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
If an afu interrupt is in flight when an eeh error is triggered the
control still reaches the function native_irq_multiplexed and the
PE-Handle read from the CXL_PSL_PEHandle_An register is 0xffff. The
function then erroneously assumes that the interrupt belonged to a
detached context and generates a warning with full stack dump in the
kernel log complaining:
"Unable to demultiplex CXL PSL IRQ for PE 65535 DSISR ffffffff DAR
ffffffff. (Possible AFU HW issue - was a term/remove acked with
outstanding transactions"
To fix this the patch adds new code to the function
native_irq_multiplexed function to compares the read value of register
CXL_PSL_PEHandle_An to ~0ULL. If true then logs a warning message
saying that the interrupt is being ignored and returns IRQ_HANDLED from
the irq handler.
Reviewed-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Acked-by: Frederic Barrat <fbarrat@linux.vnet.ibm.com>
Acked-by: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Vaibhav Jain <vaibhav@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
'cxl_dev_context_init()' returns an error pointer in case of error, not
NULL. So test it with IS_ERR.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Acked-by: Frederic Barrat <fbarrat@linux.vnet.ibm.com>
Acked-by: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
'cxl_dev_context_init()' returns an error pointer in case of error, not
NULL. So test it with IS_ERR.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Acked-by: Frederic Barrat <fbarrat@linux.vnet.ibm.com>
Acked-by: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
'cxl_context_alloc()' does not return an error pointer. It is just a
shortcut for a call to 'kzalloc' with 'sizeof(struct cxl_context)' as the
size parameter.
So its return value should be compared with NULL.
While fixing it, simplify a bit the code.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Acked-by: Frederic Barrat <fbarrat@linux.vnet.ibm.com>
Acked-by: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
In some error paths in functions cxl_start_context and
afu_ioctl_start_work pid references to the current & group-leader tasks
can leak after they are taken. This patch fixes these error paths to
release these pid references before exiting the error path.
Fixes: 7b8ad495d5 ("cxl: Fix DSI misses when the context owning task exits")
Cc: stable@vger.kernel.org # v4.5+
Reviewed-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Reported-by: Frederic Barrat <fbarrat@linux.vnet.ibm.com>
Signed-off-by: Vaibhav Jain <vaibhav@linux.vnet.ibm.com>
Acked-by: Frederic Barrat <fbarrat@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This patch prevents resetting the cxl adapter via sysfs in presence of
one or more active cxl_context on it. This protects against an
unrecoverable error caused by PSL owning a dirty cache line even after
reset and host tries to touch the same cache line. In case a force reset
of the card is required irrespective of any active contexts, the int
value -1 can be stored in the 'reset' sysfs attribute of the card.
The patch introduces a new atomic_t member named contexts_num inside
struct cxl that holds the number of active context attached to the card
, which is checked against '0' before proceeding with the reset. To
prevent against a race condition where a context is activated just after
reset check is performed, the contexts_num is atomically set to '-1'
after reset-check to indicate that no more contexts can be activated on
the card anymore.
Before activating a context we atomically test if contexts_num is
non-negative and if so, increment its value by one. In case the value of
contexts_num is negative then it indicates that the card is about to be
reset and context activation is error-ed out at that point.
Fixes: 62fa19d4b4 ("cxl: Add ability to reset the card")
Cc: stable@vger.kernel.org # v4.0+
Acked-by: Frederic Barrat <fbarrat@linux.vnet.ibm.com>
Reviewed-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Signed-off-by: Vaibhav Jain <vaibhav@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Rewrite the cxl_guest_init_afu() loop in cxl_of_probe() to use
for_each_child_of_node() rather than a hand-coded for loop.
Remove the useless of_node_put(afu_np) call after the loop, where it's
guaranteed that afu_np == NULL.
Reported-by: SF Markus Elfring <elfring@users.sourceforge.net>
Reported-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Reviewed-by: Frederic Barrat <fbarrat@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
If the capi link is going down while the PSL owns a dirty cache line,
any access from the host for that data could lead to an Uncorrectable
Error.
So when resetting the capi adapter through sysfs, make sure the PSL
cache is flushed. It won't help if there are any active Process
Elements on the card, as the cache would likely get new dirty cache
lines immediately, but if resetting an idle adapter, it should avoid
any bad surprises from data left over from terminated Process Elements.
Signed-off-by: Frederic Barrat <fbarrat@linux.vnet.ibm.com>
Reviewed-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Acked-by: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
When set_sl_ops() is called, the adapter data structure is not fully
initialized yet. Therefore the device name is not showing up in the
trace. Fix is simply to get the device name from the pci_dev
structure.
Fixes: 6d382616ac ("cxl: Abstract the differences between the PSL and XSL")
Signed-off-by: Frederic Barrat <fbarrat@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
When cxl removes a vPHB, it's possible that the pci_controller may be freed
before all references to the devices on the vPHB have been released. This
in turn causes an invalid memory access when the devices are eventually
released, as pcibios_release_device() attempts to call the phb's
release_device hook.
In cxl_pci_vphb_remove(), remove the existing call to
pcibios_free_controller(). Instead, use
pcibios_free_controller_deferred() to free the pci_controller after all
devices have been released. Export pci_set_host_bridge_release() so we can
do this.
Cc: stable@vger.kernel.org
Signed-off-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Reviewed-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Acked-by: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Switch the setting of psl_fir_cntl from debug to production
environment recommended value. It mostly affects the PSL behavior when
an error is raised in psl_fir1/2.
Tested with cxlflash.
Signed-off-by: Frederic Barrat <fbarrat@linux.vnet.ibm.com>
Reviewed-by: Uma Krishnan <ukrishn@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Make native_irq_wait() static and use NULL rather than 0 to initialise
phb->cfg_data in cxl_pci_vphb_add() to remove sparse warnings.
Signed-off-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Reviewed-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Acked-by: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Commit f67a6722d6 ("cxl: Workaround PE=0 hardware limitation in
Mellanox CX4") added a "min_pe" field to struct cxl_service_layer_ops,
to allow us to work around a Mellanox CX-4 hardware limitation.
When allocating the PE number in cxl_context_init(), we read from
ctx->afu->adapter->native->sl_ops->min_pe to get the minimum PE number.
Unsurprisingly, in a PowerVM guest ctx->afu->adapter->native is NULL,
and guests don't have a cxl_service_layer_ops struct anywhere.
Move min_pe from struct cxl_service_layer_ops to struct cxl so it's
accessible in both native and PowerVM environments. For the Mellanox
CX-4, set the min_pe value in set_sl_ops().
Fixes: f67a6722d6 ("cxl: Workaround PE=0 hardware limitation in Mellanox CX4")
Reported-by: Frederic Barrat <fbarrat@linux.vnet.ibm.com>
Signed-off-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Acked-by: Ian Munsie <imunsie@au1.ibm.com>
Reviewed-by: Frederic Barrat <fbarrat@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
If kzalloc() fails when allocating adapter->guest in
cxl_guest_init_adapter(), we call free_adapter() before erroring out.
free_adapter() in turn attempts to dereference adapter->guest, which in
this case is NULL.
In free_adapter(), skip the adapter->guest cleanup if adapter->guest is
NULL.
Fixes: 14baf4d9c7 ("cxl: Add guest-specific code")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Remove the CXL_KERNEL_API and CXL_EEH Kconfig options, as they were only
needed to coordinate the merging of the cxlflash driver. Also remove the
stub implementation of cxl_perst_reloads_same_image() in cxlflash which is
only used if CXL_EEH isn't defined (i.e. never).
Suggested-by: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Acked-by: Ian Munsie <imunsie@au1.ibm.com>
Acked-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Add a new API, cxl_check_and_switch_mode() to allow for switching of
bi-modal CAPI cards, such as the Mellanox CX-4 network card.
When a driver requests to switch a card to CAPI mode, use PCI hotplug
infrastructure to remove all PCI devices underneath the slot. We then write
an updated mode control register to the CAPI VSEC, hot reset the card, and
reprobe the card.
As the card may present a different set of PCI devices after the mode
switch, use the infrastructure provided by the pnv_php driver and the OPAL
PCI slot management facilities to ensure that:
* the old devices are removed from both the OPAL and Linux device trees
* the new devices are probed by OPAL and added to the OPAL device tree
* the new devices are added to the Linux device tree and probed through
the regular PCI device probe path
As such, introduce a new option, CONFIG_CXL_BIMODAL, with a dependency on
the pnv_php driver.
Refactor existing code that touches the mode control register in the
regular single mode case into a new function, setup_cxl_protocol_area().
Co-authored-by: Ian Munsie <imunsie@au1.ibm.com>
Cc: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Signed-off-by: Ian Munsie <imunsie@au1.ibm.com>
Reviewed-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The CX4 card cannot cope with a context with PE=0 due to a hardware
limitation, resulting in:
[ 34.166577] command failed, status limits exceeded(0x8), syndrome 0x5a7939
[ 34.166580] mlx5_core 0000:01:00.1: Failed allocating uar, aborting
Since the kernel API allocates a default context very early during
device init that will almost certainly get Process Element ID 0 there is
no easy way for us to extend the API to allow the Mellanox to inform us
of this limitation ahead of time.
Instead, work around the issue by extending the XSL structure to include
a minimum PE to allocate. Although the bug is not in the XSL, it is the
easiest place to work around this limitation given that the CX4 is
currently the only card that uses an XSL.
Signed-off-by: Ian Munsie <imunsie@au1.ibm.com>
Reviewed-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Reviewed-by: Frederic Barrat <fbarrat@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The Mellanox CX4 in cxl mode uses a hybrid interrupt model, where
interrupts are routed from the networking hardware to the XSL using the
MSIX table, and from there will be transformed back into an MSIX
interrupt using the cxl style interrupts (i.e. using IVTE entries and
ranges to map a PE and AFU interrupt number to an MSIX address).
We want to hide the implementation details of cxl interrupts as much as
possible. To this end, we use a special version of the MSI setup &
teardown routines in the PHB while in cxl mode to allocate the cxl
interrupts and configure the IVTE entries in the process element.
This function does not configure the MSIX table - the CX4 card uses a
custom format in that table and it would not be appropriate to fill that
out in generic code. The rest of the functionality is similar to the
"Full MSI-X mode" described in the CAIA, and this could be easily
extended to support other adapters that use that mode in the future.
The interrupts will be associated with the default context. If the
maximum number of interrupts per context has been limited (e.g. by the
mlx5 driver), it will automatically allocate additional kernel contexts
to associate extra interrupts as required. These contexts will be
started using the same WED that was used to start the default context.
Signed-off-by: Ian Munsie <imunsie@au1.ibm.com>
Reviewed-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The Mellanox CX4 has a hardware limitation where only 4 bits of the
AFU interrupt number can be passed to the XSL when sending an interrupt,
limiting it to only 15 interrupts per context (AFU interrupt number 0 is
invalid).
In order to overcome this, we will allocate additional contexts linked
to the default context as extra address space for the extra interrupts -
this will be implemented in the next patch.
This patch adds the preliminary support to allow this, by way of adding
a linked list in the context structure that we use to keep track of the
contexts dedicated to interrupts, and an API to simultaneously iterate
over the related context structures, AFU interrupt numbers and hardware
interrupt numbers. The point of using a single API to iterate these is
to hide some of the details of the iteration from external code, and to
reduce the number of APIs that need to be exported via base.c to allow
built in code to call.
Signed-off-by: Ian Munsie <imunsie@au1.ibm.com>
Reviewed-by: Frederic Barrat <fbarrat@linux.vnet.ibm.com>
Reviewed-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
These APIs will be used by the Mellanox CX4 support. While they function
standalone to configure existing behaviour, their primary purpose is to
allow the Mellanox driver to inform the cxl driver of a hardware
limitation, which will be used in a future patch.
Signed-off-by: Ian Munsie <imunsie@au1.ibm.com>
Reviewed-by: Frederic Barrat <fbarrat@linux.vnet.ibm.com>
Reviewed-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This hooks up support for using the kernel API with a real PHB. After
the AFU initialisation has completed it calls into the PHB code to pass
it the AFU that will be used by other peer physical functions on the
adapter.
The cxl_pci_to_afu API is extended to work with peer PCI devices,
retrieving the peer AFU from the PHB. This API may also now return an
error if it is called on a PCI device that is not associated with either
a cxl vPHB or a peer PCI device to an AFU, and this error is propagated
down.
Signed-off-by: Ian Munsie <imunsie@au1.ibm.com>
Reviewed-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The vPHB model of the cxl kernel API is a hierarchy where the AFU is
represented by the vPHB, and it's AFU configuration records are exposed
as functions under that vPHB. If there are no AFU configuration records
we will create a vPHB with nothing under it, which is a waste of
resources and will opt us into EEH handling despite not having anything
special to handle.
This also does not make sense for cards using the peer model of the cxl
kernel API, where the other functions of the device are exposed via
additional peer physical functions rather than AFU configuration
records. This model will also not work with the existing EEH handling in
the cxl driver, as that is designed around the vPHB model.
Skip creating the vPHB for AFUs without any AFU configuration records,
and opt out of EEH handling for them.
Signed-off-by: Ian Munsie <imunsie@au1.ibm.com>
Reviewed-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The cxl kernel API has a concept of a default context associated with
each PCI device under the virtual PHB. The Mellanox CX4 will also use
the cxl kernel API, but it does not use a virtual PHB - rather, the AFU
appears as a physical function as a peer to the networking functions.
In order to allow the kernel API to work with those networking
functions, we will need to associate a default context with them as
well. To this end, refactor the corresponding code to do this in vphb.c
and export it so that it can be called from the PHB code.
Signed-off-by: Ian Munsie <imunsie@au1.ibm.com>
Reviewed-by: Frederic Barrat <fbarrat@linux.vnet.ibm.com>
Reviewed-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The Mellanox CX4 uses a model where the AFU is one physical function of
the device, and is used by other peer physical functions of the same
device. This will require those other devices to grab a reference on the
AFU when they are initialised to make sure that it does not go away
during their lifetime.
Move the AFU refcount functions to base.c so they can be called from
the PHB code.
Signed-off-by: Ian Munsie <imunsie@au1.ibm.com>
Reviewed-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Reviewed-by: Frederic Barrat <fbarrat@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Devices that use CAPP DMA mode (such as the Mellanox CX4) require bus
master to be enabled in order for the CAPI traffic to flow. This should
be harmless to enable for other cxl devices, so unconditionally enable
it in the adapter init flow.
Signed-off-by: Ian Munsie <imunsie@au1.ibm.com>
Reviewed-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Reviewed-by: Frederic Barrat <fbarrat@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This extends the check that the adapter is in a CAPI capable slot so
that it may be called by external users in the kernel API. This will be
used by the upcoming Mellanox CX4 support, which needs to know ahead of
time if the card can be switched to cxl mode so that it can leave it in
PCI mode if it is not.
This API takes a parameter to check if CAPP DMA mode is supported, which
it currently only allows on P8NVL systems, since that mode currently has
issues accessing memory < 4GB on P8, and we cannot realistically avoid
that.
This API does not currently check if a CAPP unit is available (i.e. not
already assigned to another PHB) on P8. Doing so would be racy since it
is assigned on a first come first serve basis, and so long as CAPP DMA
mode is not supported on P8 we don't need this, since the only
anticipated user of this API requires CAPP DMA mode.
Cc: Philippe Bergheaud <felix@linux.vnet.ibm.com>
Signed-off-by: Ian Munsie <imunsie@au1.ibm.com>
Reviewed-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Reviewed-by: Frederic Barrat <fbarrat@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Use for_each_compatible_node() macro instead of open coding it.
Generated by Coccinelle.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Reviewed-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Acked-by: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
One should not attempt to switch a PHB into CAPI mode if there is
a switch between the PHB and the adapter. This patch modifies the
cxl driver to ignore CAPI adapters misplaced in switched slots.
Signed-off-by: Philippe Bergheaud <felix@linux.vnet.ibm.com>
Reviewed-by: Frederic Barrat <fbarrat@linux.vnet.ibm.com>
Acked-by: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The Kconfig/Makefile currently controlling compilation of this code is:
drivers/misc/cxl/Kconfig:config CXL_BASE
drivers/misc/cxl/Kconfig: bool
drivers/misc/cxl/Makefile:obj-$(CONFIG_CXL_BASE) += base.o
...meaning that it currently is not being built as a module by anyone.
Lets convert the one module_init into device_initcall so that
when reading the driver it more clear that it is builtin-only.
Since module_init translates to device_initcall in the non-modular
case, the init ordering remains unchanged with this commit.
We don't replace module.h with init.h since the file is doing
other modular stuff (module_get/put) even though it is built-in.
Cc: Ian Munsie <imunsie@au1.ibm.com>
Cc: Michael Neuling <mikey@neuling.org>
Cc: linuxppc-dev@lists.ozlabs.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The PSL Slice Error Register (PSL_SERR_An) reports implementation
dependent AFU errors, in the form of a bitmap. The PSL_SERR_An
register content is printed in the form of hex dump debug message.
This patch decodes the PSL_ERR_An register contents, and prints a
specific error message for each possible error bit. It also dumps
the secondary registers AFU_ERR_An and PSL_DSISR_An, that may
contain extra debug information.
This patch also removes the large WARN message that used to report
the cxl slice error interrupt, and replaces it by a short informative
message, that draws attention to AFU implementation errors.
Signed-off-by: Philippe Bergheaud <felix@linux.vnet.ibm.com>
Acked-by: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
If a kernel context is initialised and does not have any AFU interrupts
allocated it will cause a NULL pointer dereference when the context is
detached since the irq_names list will not have been initialised.
Move the initialisation of the irq_names list into the cxl_context_init
routine so that it will be valid for the entire lifetime of the context
and will not cause a NULL pointer dereference.
Signed-off-by: Ian Munsie <imunsie@au1.ibm.com>
Reviewed-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
An issue was noted in our debug logs where the XSL would leave the RA
bit asserted after an AFU reset operation, which would effectively
prevent further AFU reset operations from working.
Workaround the issue by clearing the RA bit with an MMIO write if it is
still asserted after any AFU control operation.
Signed-off-by: Ian Munsie <imunsie@au1.ibm.com>
Reviewed-by: Frederic Barrat <fbarrat@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The AFU disable operation has a bug where it will not clear the enable
bit and therefore will have no effect. To date this has likely been
masked by fact that we perform an AFU reset before the disable, which
also has the effect of clearing the enable bit, making the following
disable operation effectively a noop on most hardware. This patch
modifies the afu_control function to take a parameter to clear from the
AFU control register so that the disable operation can clear the
appropriate bit.
This bug was uncovered on the Mellanox CX4, which uses an XSL rather
than a PSL. On the XSL the reset operation will not complete while the
AFU is enabled, meaning the enable bit was still set at the start of the
disable and as a result this bug was hit and the disable also timed out.
Because of this difference in behaviour between the PSL and XSL, this
patch now makes the reset dependent on the card using a PSL to avoid
waiting for a timeout on the XSL. It is entirely possible that we may be
able to drop the reset altogether if it turns out we only ever needed it
due to this bug - however I am not willing to drop it without further
regression testing and have added comments to the code explaining the
background.
This also fixes a small issue where the AFU_Cntl register was read
outside of the lock that protects it.
Signed-off-by: Ian Munsie <imunsie@au1.ibm.com>
Reviewed-by: Frederic Barrat <fbarrat@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The Scheduled Process Area is allocated dynamically with enough pages to
fit at least as many processes as the AFU descriptor indicated. Since
the calculation is non-trivial, it does this by calculating how many
processes could fit in an allocation of a given order, and increasing
that order until it can fit enough processes or hits the maximum
supported size.
Currently, it will start this search using a SPA of 2 pages instead of
1. This can waste a page of memory if the AFU's maximum number of
supported processes was small enough to fit in one page.
Fix the algorithm to start the search at 1 page.
Signed-off-by: Ian Munsie <imunsie@au1.ibm.com>
Reviewed-by: Frederic Barrat <fbarrat@linux.vnet.ibm.com>
Reviewed-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
If the AFU descriptor of an AFU directed AFU indicates that it supports
0 maximum processes, we will accept that value and attempt to use it.
The SPA will still be allocated (with 2 pages due to another minor bug
and room for 958 processes), and when a context is allocated we will
pass the value of 0 to idr_alloc as the maximum. However, idr_alloc will
treat that as meaning no maximum and will allocate a context number and
we return a valid context.
Conceivably, this could lead to a buffer overflow of the SPA if more
than 958 contexts were allocated, however this is mitigated by the fact
that there are no known AFUs in the wild with a bogus AFU descriptor
like this, and that only the root user is allowed to flash an AFU image
to a card.
Add a check when validating the AFU descriptor to reject any with 0
maximum processes.
We do still allow a dedicated process only AFU to indicate that it
supports 0 contexts even though that is forbidden in the architecture,
as in that case we ignore the value and use 1 instead. This is just on
the off-chance that such a dedicated process AFU may exist (not that I
am aware of any), since their developers are less likely to have cared
about this value at all.
Signed-off-by: Ian Munsie <imunsie@au1.ibm.com>
Reviewed-by: Frederic Barrat <fbarrat@linux.vnet.ibm.com>
Reviewed-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This provides AFU drivers a means to associate private data with a cxl
context. This is particularly intended for make the new callbacks for
driver specific events easier for AFU drivers to use, as they can easily
get back to any private data structures they may use.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Philippe Bergheaud <felix@linux.vnet.ibm.com
Reviewed-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Reviewed-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This adds an afu_driver_ops structure with fetch_event() and
event_delivered() callbacks. An AFU driver such as cxlflash can fill
this out and associate it with a context to enable passing custom AFU
specific events to userspace.
This also adds a new kernel API function cxl_context_pending_events(),
that the AFU driver can use to notify the cxl driver that new specific
events are ready to be delivered, and wake up anyone waiting on the
context wait queue.
The current count of AFU driver specific events is stored in the field
afu_driver_events of the context structure.
The cxl driver checks the afu_driver_events count during poll, select,
read, etc. calls to check if an AFU driver specific event is pending,
and calls fetch_event() to obtain and deliver that event. This way, the
cxl driver takes care of all the usual locking semantics around these
calls and handles all the generic cxl events, so that the AFU driver
only needs to worry about it's own events.
fetch_event() return a struct cxl_event_afu_driver_reserved, allocated
by the AFU driver, and filled in with the specific event information and
size. Total event size (header + data) should not be greater than
CXL_READ_MIN_SIZE (4K).
Th cxl driver prepends an appropriate cxl event header, copies the event
to userspace, and finally calls event_delivered() to return the status of
the operation to the AFU driver. The event is identified by the context
and cxl_event_afu_driver_reserved pointers.
Since AFU drivers provide their own means for userspace to obtain the
AFU file descriptor (i.e. cxlflash uses an ioctl on their scsi file
descriptor to obtain the AFU file descriptor) and the generic cxl driver
will never use this event, the ABI of the event is up to each individual
AFU driver.
Signed-off-by: Philippe Bergheaud <felix@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
On bare-metal, when a device is attached to the cxl card, lsvpd shows
a location code such as (with cxlflash):
# lsvpd -l sg22
...
*YL U78CB.001.WZS0073-P1-C33-B0-T0-L0
which makes it hard to easily identify the cxl adapter owning the
flash device, since in this example C33 refers to a P8 processor.
lsvpd looks in the parent devices until it finds a location code, so the
device node for the vPHB ends up being used.
By reusing the device node of the adapter for the vPHB, lsvpd shows:
# lsvpd -l sg16
...
*YL U78C9.001.WZS09XA-P1-C7-B1-T0-L3
where C7 is the PCI slot of the cxl adapter.
On powerVM, the vPHB was already using the adapter device node, so
there's no change there.
Tested by cxlflash on bare-metal and powerVM.
Signed-off-by: Frederic Barrat <fbarrat@linux.vnet.ibm.com>
Reviewed-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Acked-by: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This adds support for using CAPP DMA mode, which is required for XSL
based cards such as the Mellanox CX4 to function.
This is currently an RFC as it depends on the corresponding support to
be merged into skiboot first, which was submitted here:
http://patchwork.ozlabs.org/patch/625582/
In the event that the skiboot on the system does not have the above
support, it will indicate as such in the kernel log and abort the init
process.
Signed-off-by: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The XSL (Translation Service Layer) is a stripped down version of the
PSL (Power Service Layer) used in some cards such as the Mellanox CX4.
Like the PSL, it implements the CAIA architecture, but has a number of
differences, mostly in it's implementation dependent registers. This
adds an ops structure to abstract these differences to bring initial
support for XSL CAPI devices.
The XSL does not implement the optional architected SERR register,
however while it treats it as a reserved register and should work with
no special treatment, attempting to access it will cause the XSL_FEC
(First Error Capture) register to be filled out, preventing it from
capturing any subsequent errors. Therefore, this patch also prevents the
kernel from trying to set up the SERR register so that the FEC register
may still be useful, and to save one interrupt.
The XSL also uses a special DMA cxl mode, which uses a slightly
different init sequence for the CAPP and PHB. The kernel support for
this will be in a future patch once the corresponding support has been
merged into skiboot.
Co-authored-by: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
In the kernel API, it is possible to attempt to allocate AFU interrupts
after already starting a context. Since the process element structure
used by the hardware is only filled out at the time the context is
started, it will not be updated with the interrupt numbers that have
just been allocated and therefore AFU interrupts will not work unless
they were allocated prior to starting the context.
This can present some difficulties as each CAPI enabled PCI device in
the kernel API has a default context, which may need to be started very
early to enable translations, potentially before interrupts can easily
be set up.
This patch makes the API more flexible to allow interrupts to be
allocated after a context has already been started and takes care of
updating the PE structure used by the hardware and notifying it to
discard any cached copy it may have.
The update is currently performed via a terminate/remove/add sequence.
This is necessary on some hardware such as the XSL that does not
properly support the update LLCMD.
Note that this is only supported on powernv at present - attempting to
perform this ordering on PowerVM will raise a warning.
Signed-off-by: Ian Munsie <imunsie@au1.ibm.com>
Reviewed-by: Frederic Barrat <fbarrat@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Make a couple more variables static. Found by sparse.
Signed-off-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Reviewed-by: fbarrat@linux.vnet.ibm.com
Reviewed-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Acked-by: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Highlights:
- Support for Power ISA 3.0 (Power9) Radix Tree MMU from Aneesh Kumar K.V
- Live patching support for ppc64le (also merged via livepatching.git)
Various cleanups & minor fixes from:
- Aaro Koskinen, Alexey Kardashevskiy, Andrew Donnellan, Aneesh Kumar K.V,
Chris Smart, Daniel Axtens, Frederic Barrat, Gavin Shan, Ian Munsie, Lennart
Sorensen, Madhavan Srinivasan, Mahesh Salgaonkar, Markus Elfring, Michael
Ellerman, Oliver O'Halloran, Paul Gortmaker, Paul Mackerras, Rashmica Gupta,
Russell Currey, Suraj Jitindar Singh, Thiago Jung Bauermann, Valentin
Rothberg, Vipin K Parashar.
General:
- Update LMB associativity index during DLPAR add/remove from Nathan Fontenot
- Fix branching to OOL handlers in relocatable kernel from Hari Bathini
- Add support for userspace Power9 copy/paste from Chris Smart
- Always use STRICT_MM_TYPECHECKS from Michael Ellerman
- Add mask of possible MMU features from Michael Ellerman
PCI:
- Enable pass through of NVLink to guests from Alexey Kardashevskiy
- Cleanups in preparation for powernv PCI hotplug from Gavin Shan
- Don't report error in eeh_pe_reset_and_recover() from Gavin Shan
- Restore initial state in eeh_pe_reset_and_recover() from Gavin Shan
- Revert "powerpc/eeh: Fix crash in eeh_add_device_early() on Cell" from Guilherme G. Piccoli
- Remove the dependency on EEH struct in DDW mechanism from Guilherme G. Piccoli
selftests:
- Test cp_abort during context switch from Chris Smart
- Add several tests for transactional memory support from Rashmica Gupta
perf:
- Add support for sampling interrupt register state from Anju T
- Add support for unwinding perf-stackdump from Chandan Kumar
cxl:
- Configure the PSL for two CAPI ports on POWER8NVL from Philippe Bergheaud
- Allow initialization on timebase sync failures from Frederic Barrat
- Increase timeout for detection of AFU mmio hang from Frederic Barrat
- Handle num_of_processes larger than can fit in the SPA from Ian Munsie
- Ensure PSL interrupt is configured for contexts with no AFU IRQs from Ian Munsie
- Add kernel API to allow a context to operate with relocate disabled from Ian Munsie
- Check periodically the coherent platform function's state from Christophe Lombard
Freescale:
- Updates from Scott: "Contains 86xx fixes, minor device tree fixes, an erratum
workaround, and a kconfig dependency fix."
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=YvyQ
-----END PGP SIGNATURE-----
Merge tag 'powerpc-4.7-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc updates from Michael Ellerman:
"Highlights:
- Support for Power ISA 3.0 (Power9) Radix Tree MMU from Aneesh Kumar K.V
- Live patching support for ppc64le (also merged via livepatching.git)
Various cleanups & minor fixes from:
- Aaro Koskinen, Alexey Kardashevskiy, Andrew Donnellan, Aneesh Kumar K.V,
Chris Smart, Daniel Axtens, Frederic Barrat, Gavin Shan, Ian Munsie,
Lennart Sorensen, Madhavan Srinivasan, Mahesh Salgaonkar, Markus Elfring,
Michael Ellerman, Oliver O'Halloran, Paul Gortmaker, Paul Mackerras,
Rashmica Gupta, Russell Currey, Suraj Jitindar Singh, Thiago Jung
Bauermann, Valentin Rothberg, Vipin K Parashar.
General:
- Update LMB associativity index during DLPAR add/remove from Nathan
Fontenot
- Fix branching to OOL handlers in relocatable kernel from Hari Bathini
- Add support for userspace Power9 copy/paste from Chris Smart
- Always use STRICT_MM_TYPECHECKS from Michael Ellerman
- Add mask of possible MMU features from Michael Ellerman
PCI:
- Enable pass through of NVLink to guests from Alexey Kardashevskiy
- Cleanups in preparation for powernv PCI hotplug from Gavin Shan
- Don't report error in eeh_pe_reset_and_recover() from Gavin Shan
- Restore initial state in eeh_pe_reset_and_recover() from Gavin Shan
- Revert "powerpc/eeh: Fix crash in eeh_add_device_early() on Cell"
from Guilherme G Piccoli
- Remove the dependency on EEH struct in DDW mechanism from Guilherme
G Piccoli
selftests:
- Test cp_abort during context switch from Chris Smart
- Add several tests for transactional memory support from Rashmica
Gupta
perf:
- Add support for sampling interrupt register state from Anju T
- Add support for unwinding perf-stackdump from Chandan Kumar
cxl:
- Configure the PSL for two CAPI ports on POWER8NVL from Philippe
Bergheaud
- Allow initialization on timebase sync failures from Frederic Barrat
- Increase timeout for detection of AFU mmio hang from Frederic
Barrat
- Handle num_of_processes larger than can fit in the SPA from Ian
Munsie
- Ensure PSL interrupt is configured for contexts with no AFU IRQs
from Ian Munsie
- Add kernel API to allow a context to operate with relocate disabled
from Ian Munsie
- Check periodically the coherent platform function's state from
Christophe Lombard
Freescale:
- Updates from Scott: "Contains 86xx fixes, minor device tree fixes,
an erratum workaround, and a kconfig dependency fix."
* tag 'powerpc-4.7-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (192 commits)
powerpc/86xx: Fix PCI interrupt map definition
powerpc/86xx: Move pci1 definition to the include file
powerpc/fsl: Fix build of the dtb embedded kernel images
powerpc/fsl: Fix rcpm compatible string
powerpc/fsl: Remove FSL_SOC dependency from FSL_LBC
powerpc/fsl-pci: Add a workaround for PCI 5 errata
powerpc/fsl: Fix SPI compatible on t208xrdb and t1040rdb
powerpc/powernv/npu: Add PE to PHB's list
powerpc/powernv: Fix insufficient memory allocation
powerpc/iommu: Remove the dependency on EEH struct in DDW mechanism
Revert "powerpc/eeh: Fix crash in eeh_add_device_early() on Cell"
powerpc/eeh: Drop unnecessary label in eeh_pe_change_owner()
powerpc/eeh: Ignore handlers in eeh_pe_reset_and_recover()
powerpc/eeh: Restore initial state in eeh_pe_reset_and_recover()
powerpc/eeh: Don't report error in eeh_pe_reset_and_recover()
Revert "powerpc/powernv: Exclude root bus in pnv_pci_reset_secondary_bus()"
powerpc/powernv/npu: Enable NVLink pass through
powerpc/powernv/npu: Rework TCE Kill handling
powerpc/powernv/npu: Add set/unset window helpers
powerpc/powernv/ioda2: Export debug helper pe_level_printk()
...
In the PowerVM environment, the PHYP CoherentAccel component manages
the state of the Coherent Accelerator Processor Interface adapter and
virtualizes CAPI resources, handles CAPP, PSL, PSL Slice errors - and
interrupts - and provides a new set of hcalls for the OS APIs to utilize
Accelerator Function Unit (AFU).
During the course of operation, a coherent platform function can
encounter errors. Some possible reason for errors are:
• Hardware recoverable and unrecoverable errors
• Transient and over-threshold correctable errors
PHYP implements its own state model for the coherent platform function.
The state of the AFU is available through a hcall.
The current implementation of the cxl driver, for the PowerVM
environment, checks this state of the AFU only when an action is
requested - open a device, ioctl command, memory map, attach/detach a
process - from an external driver - cxlflash, libcxl. If an error is
detected the cxl driver handles the error according the content of the
Power Architecture Platform Requirements document.
But in case of low-level troubles (or error injection), the PHYP
component may reset the card and change the AFU state. The PHYP
interface doesn't provide any way to be notified when that happens thus
implies that the cxl driver:
• cannot handle immediatly the state change of the AFU.
• cannot notify other drivers (cxlflash, ...)
The purpose of this patch is to wake up the cpu periodically to check
the current state of each AFU and to see if we need to enter an error
recovery path.
Signed-off-by: Christophe Lombard <clombard@linux.vnet.ibm.com>
Acked-by: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
cxl devices typically access memory using an MMU in much the same way as
the CPU, and each context includes a state register much like the MSR in
the CPU. Like the CPU, the state register includes a bit to enable
relocation, which we currently always enable.
In some cases, it may be desirable to allow a device to access memory
using real addresses instead of effective addresses, so this adds a new
API, cxl_set_translation_mode, that can be used to disable relocation
on a given kernel context. This can allow for the creation of a special
privileged context that the device can use if it needs relocation
disabled, and can use regular contexts at times when it needs relocation
enabled.
This interface is only available to users of the kernel API for obvious
reasons, and will never be supported in a virtualised environment.
This will be used by the upcoming cxl support in the mlx5 driver.
Signed-off-by: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
In the cxl kernel API, it is possible to create a context and start it
without allocating any interrupts. Since we assign or allocate the PSL
interrupt when allocating AFU interrupts this will lead to a situation
where we start the context with no means to take any faults.
The user API is not affected as it always goes through the cxl interrupt
allocation code paths and will have the PSL interrupt allocated or
assigned, even if no AFU interrupts were requested.
This checks that at least one interrupt is configured at the time of
attach, and if not it will assign the multiplexed PSL interrupt for
powernv, or allocate a single interrupt for PowerVM.
Signed-off-by: Ian Munsie <imunsie@au1.ibm.com>
Reviewed-by: Frederic Barrat <fbarrat@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
These defines are not used, but other equivalent definitions
(CXL_SPA_SW_CMD_*) are used. Remove the unused defines.
Signed-off-by: Ian Munsie <imunsie@au1.ibm.com>
Reviewed-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
num_of_process is a 16 bit field, theoretically allowing an AFU to
support 16K processes, however the scheduled process area currently has
a maximum size of 1MB, which limits the maximum number of processes to
7704.
Some AFUs may not necessarily care what the limit is and just want to be
able to use the maximum by setting the field to 16K. To allow these to
work, detect this situation and use the maximum size for the SPA.
Downgrade the WARN_ON to a dev_warn.
Signed-off-by: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
_PAGE_PRIVILEGED means the page can be accessed only by the kernel. This
is done to keep pte bits similar to PowerISA 3.0 Radix PTE format. User
pages are now marked by clearing _PAGE_PRIVILEGED bit.
Previously we allowed the kernel to have a privileged page in the lower
address range (USER_REGION). With this patch such access is denied.
We also prevent a kernel access to a non-privileged page in higher
address range (ie, REGION_ID != 0).
Both the above access scenarios should never happen.
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Jeremy Kerr <jk@ozlabs.org>
Cc: Frederic Barrat <fbarrat@linux.vnet.ibm.com>
Acked-by: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This splits the _PAGE_RW bit into _PAGE_READ and _PAGE_WRITE. It also
removes the dependency on _PAGE_USER for implying read only. Few things
to note here is that, we have read implied with write and execute
permission. Hence we should always find _PAGE_READ set on hash pte
fault.
We still can't switch PROT_NONE to !(_PAGE_RWX). Auto numa depends on
marking a prot none pte _PAGE_WRITE. (For more details look at
b191f9b106 "mm: numa: preserve PTE write permissions across a NUMA
hinting fault")
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Jeremy Kerr <jk@ozlabs.org>
Cc: Frederic Barrat <fbarrat@linux.vnet.ibm.com>
Acked-by: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
When detaching contexts, we may still have interrupts in the system
which are yet to be delivered to any CPU and be acked in the PSL.
This can result in a subsequent unrelated process getting an spurious
IRQ or an interrupt for a non-existent context.
This polls the PSL to ensure that the PSL is clear of IRQs for the
detached context, before removing the context from the idr.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Tested-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Acked-by: Ian Munsie <imunsie@au1.ibm.com>
Tested-by: Vaibhav Jain <vaibhav@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Keep IRQ mappings on context teardown. This won't leak IRQs as if we
allocate the mapping again, the generic code will give the same
mapping used last time.
Doing this works around a race in the generic code. Masking the
interrupt introduces a race which can crash the kernel or result in
IRQ that is never EOIed. The lost of EOI results in all subsequent
mappings to the same HW IRQ never receiving an interrupt.
We've seen this race with cxl test cases which are doing heavy context
startup and teardown at the same time as heavy interrupt load.
A fix to the generic code is being investigated also.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Cc: stable@vger.kernel.org # 3.8
Tested-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Acked-by: Ian Munsie <imunsie@au1.ibm.com>
Tested-by: Vaibhav Jain <vaibhav@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The current code will set _PAGE_USER to the access flags for any
fault address, because the ~ operation will be true for all address we
take a fault on. But setting _PAGE_USER also means that the fault will
be handled only if the page table have _PAGE_USER set. Hence there is
no security hole with the current code.
Now if it is an user space access, then the change in this patch really
don't have an impact because we have (!ctx->kernel) set true
and we take the if condition true.
Now kernel context created fault on an address in the kernel range
will result in a fault loop because we will not insert the
hash pte due to access and pte permission mismatch. This patch fix
the above issue.
Fixes: f204e0b8ce ("cxl: Driver code for powernv PCIe based cards for userspace access")
Reviewed-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Acked-by: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
PSL designers recommend a larger value for the mmio hang pulse, 256 us
instead of 1 us. The CAIA architecture states that it needs to be
smaller than 1/2 of the RTOS timeout set in the PHB for outbound
non-posted transactions, which is still (easily) the case here.
Signed-off-by: Frederic Barrat <fbarrat@linux.vnet.ibm.com>
Acked-by: Ian Munsie <imunsie@au1.ibm.com>
Tested-by: Frank Haverkamp <haver@linux.vnet.ibm.com>
Tested-by: Manoj Kumar <manoj@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Failure to synchronize the PSL timebase currently prevents the
initialization of the cxl card, thus rendering the card useless. This
is too extreme for a feature which is rarely used, if at all. No
hardware AFUs or software is currently using PSL timebase.
This patch still tries to synchronize the PSL timebase when the card
is initialized, but ignores the error if it can't. Instead, it reports
a status via /sys.
Signed-off-by: Frederic Barrat <fbarrat@linux.vnet.ibm.com>
Acked-by: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The kfree() function tests whether its argument is NULL and then
returns immediately. Thus the test around the call is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Reviewed-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Acked-by: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The POWER8NVL chip has two CAPI ports. Configure the PSL to route
data to the port corresponding to the CAPP unit.
Signed-off-by: Philippe Bergheaud <felix@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Function cxl_get_phys_dev() was removed from the kernel API by a
previous patch, but it's actually dead code. Remove it.
Signed-off-by: Frederic Barrat <fbarrat@linux.vnet.ibm.com>
Acked-by: Ian Munsie <imunsie@au1.ibm.com>
Reviewed-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Acked-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Highlights:
- Restructure Linux PTE on Book3S/64 to Radix format from Paul Mackerras
- Book3s 64 MMU cleanup in preparation for Radix MMU from Aneesh Kumar K.V
- Add POWER9 cputable entry from Michael Neuling
- FPU/Altivec/VSX save/restore optimisations from Cyril Bur
- Add support for new ftrace ABI on ppc64le from Torsten Duwe
Various cleanups & minor fixes from:
- Adam Buchbinder, Andrew Donnellan, Balbir Singh, Christophe Leroy, Cyril
Bur, Luis Henriques, Madhavan Srinivasan, Pan Xinhui, Russell Currey,
Sukadev Bhattiprolu, Suraj Jitindar Singh.
General:
- atomics: Allow architectures to define their own __atomic_op_* helpers from
Boqun Feng
- Implement atomic{, 64}_*_return_* variants and acquire/release/relaxed
variants for (cmp)xchg from Boqun Feng
- Add powernv_defconfig from Jeremy Kerr
- Fix BUG_ON() reporting in real mode from Balbir Singh
- Add xmon command to dump OPAL msglog from Andrew Donnellan
- Add xmon command to dump process/task similar to ps(1) from Douglas Miller
- Clean up memory hotplug failure paths from David Gibson
pci/eeh:
- Redesign SR-IOV on PowerNV to give absolute isolation between VFs from Wei
Yang.
- EEH Support for SRIOV VFs from Wei Yang and Gavin Shan.
- PCI/IOV: Rename and export virtfn_{add, remove} from Wei Yang
- PCI: Add pcibios_bus_add_device() weak function from Wei Yang
- MAINTAINERS: Update EEH details and maintainership from Russell Currey
cxl:
- Support added to the CXL driver for running on both bare-metal and
hypervisor systems, from Christophe Lombard and Frederic Barrat.
- Ignore probes for virtual afu pci devices from Vaibhav Jain
perf:
- Export Power8 generic and cache events to sysfs from Sukadev Bhattiprolu
- hv-24x7: Fix usage with chip events, display change in counter values,
display domain indices in sysfs, eliminate domain suffix in event names,
from Sukadev Bhattiprolu
Freescale:
- Updates from Scott: "Highlights include 8xx optimizations, 32-bit checksum
optimizations, 86xx consolidation, e5500/e6500 cpu hotplug, more fman and
other dt bits, and minor fixes/cleanup."
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=qkAt
-----END PGP SIGNATURE-----
Merge tag 'powerpc-4.6-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc updates from Michael Ellerman:
"This was delayed a day or two by some build-breakage on old toolchains
which we've now fixed.
There's two PCI commits both acked by Bjorn.
There's one commit to mm/hugepage.c which is (co)authored by Kirill.
Highlights:
- Restructure Linux PTE on Book3S/64 to Radix format from Paul
Mackerras
- Book3s 64 MMU cleanup in preparation for Radix MMU from Aneesh
Kumar K.V
- Add POWER9 cputable entry from Michael Neuling
- FPU/Altivec/VSX save/restore optimisations from Cyril Bur
- Add support for new ftrace ABI on ppc64le from Torsten Duwe
Various cleanups & minor fixes from:
- Adam Buchbinder, Andrew Donnellan, Balbir Singh, Christophe Leroy,
Cyril Bur, Luis Henriques, Madhavan Srinivasan, Pan Xinhui, Russell
Currey, Sukadev Bhattiprolu, Suraj Jitindar Singh.
General:
- atomics: Allow architectures to define their own __atomic_op_*
helpers from Boqun Feng
- Implement atomic{, 64}_*_return_* variants and acquire/release/
relaxed variants for (cmp)xchg from Boqun Feng
- Add powernv_defconfig from Jeremy Kerr
- Fix BUG_ON() reporting in real mode from Balbir Singh
- Add xmon command to dump OPAL msglog from Andrew Donnellan
- Add xmon command to dump process/task similar to ps(1) from Douglas
Miller
- Clean up memory hotplug failure paths from David Gibson
pci/eeh:
- Redesign SR-IOV on PowerNV to give absolute isolation between VFs
from Wei Yang.
- EEH Support for SRIOV VFs from Wei Yang and Gavin Shan.
- PCI/IOV: Rename and export virtfn_{add, remove} from Wei Yang
- PCI: Add pcibios_bus_add_device() weak function from Wei Yang
- MAINTAINERS: Update EEH details and maintainership from Russell
Currey
cxl:
- Support added to the CXL driver for running on both bare-metal and
hypervisor systems, from Christophe Lombard and Frederic Barrat.
- Ignore probes for virtual afu pci devices from Vaibhav Jain
perf:
- Export Power8 generic and cache events to sysfs from Sukadev
Bhattiprolu
- hv-24x7: Fix usage with chip events, display change in counter
values, display domain indices in sysfs, eliminate domain suffix in
event names, from Sukadev Bhattiprolu
Freescale:
- Updates from Scott: "Highlights include 8xx optimizations, 32-bit
checksum optimizations, 86xx consolidation, e5500/e6500 cpu
hotplug, more fman and other dt bits, and minor fixes/cleanup"
* tag 'powerpc-4.6-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (179 commits)
powerpc: Fix unrecoverable SLB miss during restore_math()
powerpc/8xx: Fix do_mtspr_cpu6() build on older compilers
powerpc/rcpm: Fix build break when SMP=n
powerpc/book3e-64: Use hardcoded mttmr opcode
powerpc/fsl/dts: Add "jedec,spi-nor" flash compatible
powerpc/T104xRDB: add tdm riser card node to device tree
powerpc32: PAGE_EXEC required for inittext
powerpc/mpc85xx: Add pcsphy nodes to FManV3 device tree
powerpc/mpc85xx: Add MDIO bus muxing support to the board device tree(s)
powerpc/86xx: Introduce and use common dtsi
powerpc/86xx: Update device tree
powerpc/86xx: Move dts files to fsl directory
powerpc/86xx: Switch to kconfig fragments approach
powerpc/86xx: Update defconfigs
powerpc/86xx: Consolidate common platform code
powerpc32: Remove one insn in mulhdu
powerpc32: small optimisation in flush_icache_range()
powerpc: Simplify test in __dma_sync()
powerpc32: move xxxxx_dcache_range() functions inline
powerpc32: Remove clear_pages() and define clear_page() inline
...
Here is the big char/misc driver update for 4.6-rc1.
The majority of the patches here is hwtracing and some new mic drivers,
but there's a lot of other driver updates as well. Full details in the
shortlog.
All have been in linux-next for a while with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlbp9IcACgkQMUfUDdst+ykyJgCeLTC2QNGrh51kiJglkVJ0yD36
q4MAn0NkvSX2+iv5Jq8MaX6UQoRa4Nun
=MNjR
-----END PGP SIGNATURE-----
Merge tag 'char-misc-4.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc updates from Greg KH:
"Here is the big char/misc driver update for 4.6-rc1.
The majority of the patches here is hwtracing and some new mic
drivers, but there's a lot of other driver updates as well. Full
details in the shortlog.
All have been in linux-next for a while with no reported issues"
* tag 'char-misc-4.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (238 commits)
goldfish: Fix build error of missing ioremap on UM
nvmem: mediatek: Fix later provider initialization
nvmem: imx-ocotp: Fix return value of imx_ocotp_read
nvmem: Fix dependencies for !HAS_IOMEM archs
char: genrtc: replace blacklist with whitelist
drivers/hwtracing: make coresight-etm-perf.c explicitly non-modular
drivers: char: mem: fix IS_ERROR_VALUE usage
char: xillybus: Fix internal data structure initialization
pch_phub: return -ENODATA if ROM can't be mapped
Drivers: hv: vmbus: Support kexec on ws2012 r2 and above
Drivers: hv: vmbus: Support handling messages on multiple CPUs
Drivers: hv: utils: Remove util transport handler from list if registration fails
Drivers: hv: util: Pass the channel information during the init call
Drivers: hv: vmbus: avoid unneeded compiler optimizations in vmbus_wait_for_unload()
Drivers: hv: vmbus: remove code duplication in message handling
Drivers: hv: vmbus: avoid wait_for_completion() on crash
Drivers: hv: vmbus: don't loose HVMSG_TIMER_EXPIRED messages
misc: at24: replace memory_accessor with nvmem_device_read
eeprom: 93xx46: extend driver to plug into the NVMEM framework
eeprom: at25: extend driver to plug into the NVMEM framework
...
Add a check at the beginning of cxl_probe function to ignore virtual pci
devices created for each afu registered. This fixes the the errors
messages logged about missing CXL vsec, when cxl probe is unable to
find necessary vsec entries in device pci config space. The error
message logged are of the form :
cxl-pci 0004:00:00.0: ABORTING: CXL VSEC not found!
cxl-pci 0004:00:00.0: cxl_init_adapter failed: -19
Cc: Ian Munsie <imunsie@au1.ibm.com>
Cc: Frederic Barrat <fbarrat@linux.vnet.ibm.com>
Signed-off-by: Vaibhav Jain <vaibhav@linux.vnet.ibm.com>
Reviewed-by: fbarrat@linux.vnet.ibm.com
Reviewed-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Acked-by: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The cxl_get_phys_dev() API returns a struct device pointer which could
belong to either a struct pci_dev (bare-metal) or platform_device
(powerVM). To avoid potential problems in drivers, remove that API. It
was introduced to allow drivers to read the VPD of the adapter, but
the cxl driver now provides the cxl_pci_read_adapter_vpd() API for
that purpose.
Co-authored-by: Christophe Lombard <clombard@linux.vnet.ibm.com>
Signed-off-by: Frederic Barrat <fbarrat@linux.vnet.ibm.com>
Signed-off-by: Christophe Lombard <clombard@linux.vnet.ibm.com>
Acked-by: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
To ease debugging, add a few tracepoints around the cxl hcalls.
Co-authored-by: Frederic Barrat <fbarrat@linux.vnet.ibm.com>
Signed-off-by: Frederic Barrat <fbarrat@linux.vnet.ibm.com>
Signed-off-by: Christophe Lombard <clombard@linux.vnet.ibm.com>
Reviewed-by: Manoj Kumar <manoj@linux.vnet.ibm.com>
Acked-by: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Check the AFU state whenever an API is called. The hypervisor may
issue a reset of the adapter when it detects a fault. When it happens,
it launches an error recovery which will either move the AFU to a
permanent failure state, or in the disabled state.
If the AFU is found to be disabled, detach all existing contexts from
it before issuing a AFU reset to re-enable it.
Before detaching contexts, notify any kernel driver through the EEH
callbacks of the AFU pci device.
Co-authored-by: Frederic Barrat <fbarrat@linux.vnet.ibm.com>
Signed-off-by: Frederic Barrat <fbarrat@linux.vnet.ibm.com>
Signed-off-by: Christophe Lombard <clombard@linux.vnet.ibm.com>
Reviewed-by: Manoj Kumar <manoj@linux.vnet.ibm.com>
Acked-by: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Like on bare-metal, the cxl driver creates a virtual PHB and a pci
device for the AFU. The configuration space of the device is mapped to
the configuration record of the AFU.
Reuse the code defined in afu_cr_read8|16|32() when reading the
configuration space of the AFU device.
Even though the (virtual) AFU device is a pci device, the adapter is
not. So a driver using the cxl kernel API cannot read the VPD of the
adapter through the usual PCI interface. Therefore, we add a call to
the cxl kernel API:
ssize_t cxl_read_adapter_vpd(struct pci_dev *dev, void *buf, size_t count);
Co-authored-by: Christophe Lombard <clombard@linux.vnet.ibm.com>
Signed-off-by: Frederic Barrat <fbarrat@linux.vnet.ibm.com>
Signed-off-by: Christophe Lombard <clombard@linux.vnet.ibm.com>
Reviewed-by: Manoj Kumar <manoj@linux.vnet.ibm.com>
Acked-by: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Add new entry point to scan the device tree at boot in a guest,
looking for cxl devices.
Co-authored-by: Christophe Lombard <clombard@linux.vnet.ibm.com>
Signed-off-by: Frederic Barrat <fbarrat@linux.vnet.ibm.com>
Signed-off-by: Christophe Lombard <clombard@linux.vnet.ibm.com>
Reviewed-by: Manoj Kumar <manoj@linux.vnet.ibm.com>
Acked-by: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The new flash.c file contains the logic to flash a new image on the
adapter, through a hcall. It is an iterative process, with chunks of
data of 1M at a time. There are also 2 phases: write and verify. The
flash operation itself is driven from a user-land tool.
Once flashing is successful, an rtas call is made to update the device
tree with the new properties values for the adapter and the AFU(s)
Add a new char device for the adapter, so that the flash tool can
access the card, even if there is no valid AFU on it.
Co-authored-by: Frederic Barrat <fbarrat@linux.vnet.ibm.com>
Signed-off-by: Frederic Barrat <fbarrat@linux.vnet.ibm.com>
Signed-off-by: Christophe Lombard <clombard@linux.vnet.ibm.com>
Reviewed-by: Manoj Kumar <manoj@linux.vnet.ibm.com>
Acked-by: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Filter out a few adapter parameters which don't make sense in a guest.
Document the changes.
Co-authored-by: Frederic Barrat <fbarrat@linux.vnet.ibm.com>
Signed-off-by: Frederic Barrat <fbarrat@linux.vnet.ibm.com>
Signed-off-by: Christophe Lombard <clombard@linux.vnet.ibm.com>
Reviewed-by: Manoj Kumar <manoj@linux.vnet.ibm.com>
Acked-by: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The new of.c file contains code to parse the device tree to find out
about cxl adapters and AFUs.
guest.c implements the guest-specific callbacks for the backend API.
The process element ID is not known until the context is attached, so
we have to separate the context ID assigned by the cxl driver from the
process element ID visible to the user applications. In bare-metal,
the 2 IDs match.
Co-authored-by: Frederic Barrat <fbarrat@linux.vnet.ibm.com>
Signed-off-by: Frederic Barrat <fbarrat@linux.vnet.ibm.com>
Signed-off-by: Christophe Lombard <clombard@linux.vnet.ibm.com>
Reviewed-by: Manoj Kumar <manoj@linux.vnet.ibm.com>
Acked-by: Ian Munsie <imunsie@au1.ibm.com>
[mpe: Fix SMP=n build, fix PSERIES=n build, minor whitespace fixes]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Introduce sub-structures containing the bare-metal specific fields in
the structures describing the adapter (struct cxl) and AFU (struct
cxl_afu).
Update all their references.
Co-authored-by: Frederic Barrat <fbarrat@linux.vnet.ibm.com>
Signed-off-by: Frederic Barrat <fbarrat@linux.vnet.ibm.com>
Signed-off-by: Christophe Lombard <clombard@linux.vnet.ibm.com>
Reviewed-by: Manoj Kumar <manoj@linux.vnet.ibm.com>
Acked-by: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The hypervisor calls provide an interface with a coherent platform
facility and function. It matches version 0.16 of the 'PAPR changes'
document.
The following hcalls are supported:
H_ATTACH_CA_PROCESS Attach a process element to a coherent platform
function.
H_DETACH_CA_PROCESS Detach a process element from a coherent
platform function.
H_CONTROL_CA_FUNCTION Allow the partition to manipulate or query
certain coherent platform function behaviors.
H_COLLECT_CA_INT_INFO Collect interrupt info about a coherent.
platform function after an interrupt occurred
H_CONTROL_CA_FAULTS Control the operation of a coherent platform
function after a fault occurs.
H_DOWNLOAD_CA_FACILITY Support for downloading a base adapter image to
the coherent platform facility, and for
validating the entire image after the download.
H_CONTROL_CA_FACILITY Allow the partition to manipulate or query
certain coherent platform facility behaviors.
Co-authored-by: Frederic Barrat <fbarrat@linux.vnet.ibm.com>
Signed-off-by: Frederic Barrat <fbarrat@linux.vnet.ibm.com>
Signed-off-by: Christophe Lombard <clombard@linux.vnet.ibm.com>
Reviewed-by: Manoj Kumar <manoj@linux.vnet.ibm.com>
Acked-by: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The PSL interrupt cannot be multiplexed in a guest, as it is not
supported by the hypervisor. So an interrupt will be allocated
for it for each context. It will still be the first interrupt found in
the first interrupt range, but is treated almost like any other AFU
interrupt when creating/deleting the context. Only the handler is
different. Rework the code so that the range 0 is treated like the
other ranges.
Co-authored-by: Christophe Lombard <clombard@linux.vnet.ibm.com>
Signed-off-by: Frederic Barrat <fbarrat@linux.vnet.ibm.com>
Signed-off-by: Christophe Lombard <clombard@linux.vnet.ibm.com>
Reviewed-by: Manoj Kumar <manoj@linux.vnet.ibm.com>
Acked-by: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
A few functions are mostly common between bare-metal and guest and
just need minor tuning. To avoid crowding the backend API, introduce a
few 'if' based on the CPU being in HV mode.
Co-authored-by: Christophe Lombard <clombard@linux.vnet.ibm.com>
Signed-off-by: Frederic Barrat <fbarrat@linux.vnet.ibm.com>
Signed-off-by: Christophe Lombard <clombard@linux.vnet.ibm.com>
Reviewed-by: Manoj Kumar <manoj@linux.vnet.ibm.com>
Acked-by: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Rename a few functions, changing the 'cxl_' prefix to either
'cxl_pci_' or 'cxl_native_', to make clear that the implementation is
bare-metal specific.
Those functions will have an equivalent implementation for a guest in
a later patch.
Co-authored-by: Christophe Lombard <clombard@linux.vnet.ibm.com>
Signed-off-by: Frederic Barrat <fbarrat@linux.vnet.ibm.com>
Signed-off-by: Christophe Lombard <clombard@linux.vnet.ibm.com>
Reviewed-by: Manoj Kumar <manoj@linux.vnet.ibm.com>
Acked-by: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The backend API (in cxl.h) lists some low-level functions whose
implementation is different on bare-metal and in a guest. Each
environment implements its own functions, and the common code uses
them through function pointers, defined in cxl_backend_ops
Co-authored-by: Christophe Lombard <clombard@linux.vnet.ibm.com>
Signed-off-by: Frederic Barrat <fbarrat@linux.vnet.ibm.com>
Signed-off-by: Christophe Lombard <clombard@linux.vnet.ibm.com>
Reviewed-by: Manoj Kumar <manoj@linux.vnet.ibm.com>
Acked-by: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
CXL kernel API was defining the process problem state area during
context initialization, making it possible to map the problem state
area before attaching the context. This won't work on a powerVM
guest. So force the logical behavior, like in userspace: attach first,
then map the problem state area.
Remove calls to cxl_assign_psn_space during init. The function is
already called on the attach paths.
Co-authored-by: Christophe Lombard <clombard@linux.vnet.ibm.com>
Signed-off-by: Frederic Barrat <fbarrat@linux.vnet.ibm.com>
Signed-off-by: Christophe Lombard <clombard@linux.vnet.ibm.com>
Reviewed-by: Manoj Kumar <manoj@linux.vnet.ibm.com>
Acked-by: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Move a few functions around to better separate code specific to
bare-metal environment from code which will be commonly used between
guest and bare-metal.
Code specific to bare-metal is meant to be in native.c or pci.c
only. It's basically anything which touches the card p1 registers,
some p2 registers not needed from a guest and the PCI interface.
Co-authored-by: Christophe Lombard <clombard@linux.vnet.ibm.com>
Signed-off-by: Frederic Barrat <fbarrat@linux.vnet.ibm.com>
Signed-off-by: Christophe Lombard <clombard@linux.vnet.ibm.com>
Reviewed-by: Manoj Kumar <manoj@linux.vnet.ibm.com>
Acked-by: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Move around some functions which will be accessed from the bare-metal
and guest environments.
Code in native.c and pci.c is meant to be bare-metal specific.
Other files contain code which may be shared with guests.
Co-authored-by: Frederic Barrat <fbarrat@linux.vnet.ibm.com>
Signed-off-by: Frederic Barrat <fbarrat@linux.vnet.ibm.com>
Signed-off-by: Christophe Lombard <clombard@linux.vnet.ibm.com>
Reviewed-by: Manoj Kumar <manoj@linux.vnet.ibm.com>
Acked-by: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The PSL timebase synchronization is seemingly failing for
configuration not including VIRT_CPU_ACCOUNTING_NATIVE. The driver
shows the following trace in dmesg:
PSL: Timebase sync: giving up!
The PSL timebase register is actually syncing correctly, but the cxl
driver is not detecting it. Fix is to use the proper timebase-to-time
conversion.
Signed-off-by: Frederic Barrat <fbarrat@linux.vnet.ibm.com>
Cc: <stable@vger.kernel.org> # 4.3+
Acked-by: Michael Neuling <mikey@neuling.org>
Reviewed-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Acked-by: Ian Munsie <imunsie@au1.ibm.com>
Reviewed-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Reviewed-by: Vaibhav Jain <vaibhav@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Use kobj_to_dev() instead of open-coding it.
Signed-off-by: Geliang Tang <geliangtang@163.com>
Reviewed-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Acked-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Drivers should include asm/pci-bridge.h only when they need the arch-
specific things provided there. Outside of the arch/ directories, the only
drivers that actually need things provided by asm/pci-bridge.h are the
powerpc RPA hotplug drivers in drivers/pci/hotplug/rpa*.
Remove the includes of asm/pci-bridge.h from the other drivers, adding an
include of linux/pci.h if necessary.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
- Ground work for the new Power9 MMU from Aneesh Kumar K.V
- Optimise FP/VMX/VSX context switching from Anton Blanchard
- Various cleanups from Krzysztof Kozlowski, John Ogness, Rashmica Gupta,
Russell Currey, Gavin Shan, Daniel Axtens, Michael Neuling, Andrew Donnellan
- Allow wrapper to work on non-english system from Laurent Vivier
- Add rN aliases to the pt_regs_offset table from Rashmica Gupta
- Fix module autoload for rackmeter & axonram drivers from Luis de Bethencourt
- Include KVM guest test in all interrupt vectors from Paul Mackerras
- Fix DSCR inheritance over fork() from Anton Blanchard
- Make value-returning atomics & {cmp}xchg* & their atomic_ versions fully ordered from Boqun Feng
- Print MSR TM bits in oops messages from Michael Neuling
- Add TM signal return & invalid stack selftests from Michael Neuling
- Limit EPOW reset event warnings from Vipin K Parashar
- Remove the Cell QPACE code from Rashmica Gupta
- Append linux_banner to exception information in xmon from Rashmica Gupta
- Add selftest to check if VSRs are corrupted from Rashmica Gupta
- Remove broken GregorianDay() from Daniel Axtens
- Import Anton's context_switch2 benchmark into selftests from Michael Ellerman
- Add selftest script to test HMI functionality from Daniel Axtens
- Remove obsolete OPAL v2 support from Stewart Smith
- Make enter_rtas() private from Michael Ellerman
- PPR exception cleanups from Michael Ellerman
- Add page soft dirty tracking from Laurent Dufour
- Add support for Nvlink NPUs from Alistair Popple
- Add support for kexec on 476fpe from Alistair Popple
- Enable kernel CPU dlpar from sysfs from Nathan Fontenot
- Copy only required pieces of the mm_context_t to the paca from Michael Neuling
- Add a kmsg_dumper that flushes OPAL console output on panic from Russell Currey
- Implement save_stack_trace_regs() to enable kprobe stack tracing from Steven Rostedt
- Add HWCAP bits for Power9 from Michael Ellerman
- Fix _PAGE_PTE breaking swapoff from Aneesh Kumar K.V
- Fix _PAGE_SWP_SOFT_DIRTY breaking swapoff from Hugh Dickins
- scripts/recordmcount.pl: support data in text section on powerpc from Ulrich Weigand
- Handle R_PPC64_ENTRY relocations in modules from Ulrich Weigand
- cxl: Fix possible idr warning when contexts are released from Vaibhav Jain
- cxl: use correct operator when writing pcie config space values from Andrew Donnellan
- cxl: Fix DSI misses when the context owning task exits from Vaibhav Jain
- cxl: fix build for GCC 4.6.x from Brian Norris
- cxl: use -Werror only with CONFIG_PPC_WERROR from Brian Norris
- cxl: Enable PCI device ID for future IBM CXL adapter from Uma Krishnan
- Freescale updates from Scott: Highlights include moving QE code out of
arch/powerpc (to be shared with arm), device tree updates, and minor fixes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=R5bX
-----END PGP SIGNATURE-----
Merge tag 'powerpc-4.5-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc updates from Michael Ellerman:
"Core:
- Ground work for the new Power9 MMU from Aneesh Kumar K.V
- Optimise FP/VMX/VSX context switching from Anton Blanchard
Misc:
- Various cleanups from Krzysztof Kozlowski, John Ogness, Rashmica
Gupta, Russell Currey, Gavin Shan, Daniel Axtens, Michael Neuling,
Andrew Donnellan
- Allow wrapper to work on non-english system from Laurent Vivier
- Add rN aliases to the pt_regs_offset table from Rashmica Gupta
- Fix module autoload for rackmeter & axonram drivers from Luis de
Bethencourt
- Include KVM guest test in all interrupt vectors from Paul Mackerras
- Fix DSCR inheritance over fork() from Anton Blanchard
- Make value-returning atomics & {cmp}xchg* & their atomic_ versions
fully ordered from Boqun Feng
- Print MSR TM bits in oops messages from Michael Neuling
- Add TM signal return & invalid stack selftests from Michael Neuling
- Limit EPOW reset event warnings from Vipin K Parashar
- Remove the Cell QPACE code from Rashmica Gupta
- Append linux_banner to exception information in xmon from Rashmica
Gupta
- Add selftest to check if VSRs are corrupted from Rashmica Gupta
- Remove broken GregorianDay() from Daniel Axtens
- Import Anton's context_switch2 benchmark into selftests from
Michael Ellerman
- Add selftest script to test HMI functionality from Daniel Axtens
- Remove obsolete OPAL v2 support from Stewart Smith
- Make enter_rtas() private from Michael Ellerman
- PPR exception cleanups from Michael Ellerman
- Add page soft dirty tracking from Laurent Dufour
- Add support for Nvlink NPUs from Alistair Popple
- Add support for kexec on 476fpe from Alistair Popple
- Enable kernel CPU dlpar from sysfs from Nathan Fontenot
- Copy only required pieces of the mm_context_t to the paca from
Michael Neuling
- Add a kmsg_dumper that flushes OPAL console output on panic from
Russell Currey
- Implement save_stack_trace_regs() to enable kprobe stack tracing
from Steven Rostedt
- Add HWCAP bits for Power9 from Michael Ellerman
- Fix _PAGE_PTE breaking swapoff from Aneesh Kumar K.V
- Fix _PAGE_SWP_SOFT_DIRTY breaking swapoff from Hugh Dickins
- scripts/recordmcount.pl: support data in text section on powerpc
from Ulrich Weigand
- Handle R_PPC64_ENTRY relocations in modules from Ulrich Weigand
cxl:
- cxl: Fix possible idr warning when contexts are released from
Vaibhav Jain
- cxl: use correct operator when writing pcie config space values
from Andrew Donnellan
- cxl: Fix DSI misses when the context owning task exits from Vaibhav
Jain
- cxl: fix build for GCC 4.6.x from Brian Norris
- cxl: use -Werror only with CONFIG_PPC_WERROR from Brian Norris
- cxl: Enable PCI device ID for future IBM CXL adapter from Uma
Krishnan
Freescale:
- Freescale updates from Scott: Highlights include moving QE code out
of arch/powerpc (to be shared with arm), device tree updates, and
minor fixes"
* tag 'powerpc-4.5-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (149 commits)
powerpc/module: Handle R_PPC64_ENTRY relocations
scripts/recordmcount.pl: support data in text section on powerpc
powerpc/powernv: Fix OPAL_CONSOLE_FLUSH prototype and usages
powerpc/mm: fix _PAGE_SWP_SOFT_DIRTY breaking swapoff
powerpc/mm: Fix _PAGE_PTE breaking swapoff
cxl: Enable PCI device ID for future IBM CXL adapter
cxl: use -Werror only with CONFIG_PPC_WERROR
cxl: fix build for GCC 4.6.x
powerpc: Add HWCAP bits for Power9
powerpc/powernv: Reserve PE#0 on NPU
powerpc/powernv: Change NPU PE# assignment
powerpc/powernv: Fix update of NVLink DMA mask
powerpc/powernv: Remove misleading comment in pci.c
powerpc: Implement save_stack_trace_regs() to enable kprobe stack tracing
powerpc: Fix build break due to paca mm_context_t changes
cxl: Fix DSI misses when the context owning task exits
MAINTAINERS: Update Scott Wood's e-mail address
powerpc/powernv: Fix minor off-by-one error in opal_mce_check_early_recovery()
powerpc: Fix style of self-test config prompts
powerpc/powernv: Only delay opal_rtc_read() retry when necessary
...
Add support for future IBM Coherent Accelerator (CXL) device
with ID of 0x0601.
Signed-off-by: Uma Krishnan <ukrishn@linux.vnet.ibm.com>
Reviewed-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Some developers really like to have -Werror enabled for their code, as
it helps to ensure warning free code. Others don't want -Werror, as it
(for example) can cause problems when newer (or older) compilers have
different sets of warnings, or new warnings can appear just when turning
up the warning level (e.g., make W=1 or W=2). Thus, it seems prudent to
have the use of -Werror be configurable.
It so happens that cxl is only built on PowerPC, and PowerPC already
has a nice set of Kconfig options for this, under CONFIG_PPC_WERROR. So
let's use that, and the world is a happy place again! (Note that
PPC_WERROR defaults to =y, so the common case compile should still be
enforcing -Werror.)
Fixes: d3d73f4b38 ("cxl: Compile with -Werror")
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
GCC 4.6.3 does not support -Wno-unused-const-variable. Instead, use the
kbuild infrastructure that checks if this options exists.
Fixes: 2cd55c68c0 ("cxl: Fix build failure due to -Wunused-variable behaviour change")
Suggested-by: Michal Marek <mmarek@suse.com>
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Presently when a user-space process issues CXL_IOCTL_START_WORK ioctl we
store the pid of the current task_struct and use it to get pointer to
the mm_struct of the process, while processing page or segment faults
from the capi card. However this causes issues when the thread that had
originally issued the start-work ioctl exits in which case the stored
pid is no more valid and the cxl driver is unable to handle faults as
the mm_struct corresponding to process is no more accessible.
This patch fixes this issue by using the mm_struct of the next alive
task in the thread group. This is done by iterating over all the tasks
in the thread group starting from thread group leader and calling
get_task_mm on each one of them. When a valid mm_struct is obtained the
pid of the associated task is stored in the context replacing the
exiting one for handling future faults.
The patch introduces a new function named get_mem_context that checks if
the current task pointed to by ctx->pid is dead? If yes it performs the
steps described above. Also a new variable cxl_context.glpid is
introduced which stores the pid of the thread group leader associated
with the context owning task.
Reported-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Reported-by: Frank Haverkamp <HAVERKAM@de.ibm.com>
Suggested-by: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Vaibhav Jain <vaibhav@linux.vnet.ibm.com>
Acked-by: Ian Munsie <imunsie@au1.ibm.com>
Reviewed-by: Frederic Barrat <fbarrat@linux.vnet.ibm.com>
Reviewed-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
A process element (defined in CAIA) keeps track of the endianess of
contexts through the Little Endian (LE) bit of the State Register. It
is currently set for user contexts, but was somehow forgotten for
kernel contexts, so this patch fixes it.
It could lead to erratic behavior from an AFU when the context is
attached through the kernel API.
Fixes: 2f663527bd ("cxl: Configure PSL for kernel contexts and merge code")
Cc: stable@vger.kernel.org # 4.2+
Signed-off-by: Frederic Barrat <fbarrat@linux.vnet.ibm.com>
Suggested-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
When writing a value to config space, cxl_pcie_write_config() calls
cxl_pcie_config_info() to obtain a mask and shift value, shifts the new
value accordingly, then uses the mask to combine the shifted value with the
existing value at the address as part of a read-modify-write pattern.
Currently, we use a logical OR operator rather than a bitwise OR operator,
which means any use of this function results in an incorrect value being
written. Replace the logical OR operator with a bitwise OR operator so the
value is written correctly.
Reported-by: Michael Ellerman <mpe@ellerman.id.au>
Cc: stable@vger.kernel.org
Fixes: 6f7f0b3df6 ("cxl: Add AFU virtual PHB and kernel API")
Signed-off-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Acked-by: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
An idr warning is reported when a context is release after the capi card
is unbound from the cxl driver via sysfs. Below are the steps to
reproduce:
1. Create multiple afu contexts in an user-space application using libcxl.
2. Unbind capi card from cxl using command of form
echo <capi-card-pci-addr> > /sys/bus/pci/drivers/cxl-pci/unbind
3. Exit/kill the application owning afu contexts.
After above steps a warning message is usually seen in the kernel logs
of the form "idr_remove called for id=<context-id> which is not
allocated."
This is caused by the function cxl_release_afu which destroys the
contexts_idr table. So when a context is release no entry for context pe
is found in the contexts_idr table and idr code prints this warning.
This patch fixes this issue by increasing & decreasing the ref-count on
the afu device when a context is initialized or when its freed
respectively. This prevents the afu from being released until all the
afu contexts have been released. The patch introduces two new functions
namely cxl_afu_get/put that manage the ref-count on the afu device.
Also the patch removes code inside cxl_dev_context_init that increases ref
on the afu device as its guaranteed to be alive during this function.
Reported-by: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Vaibhav Jain <vaibhav@linux.vnet.ibm.com>
Acked-by: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
- Kconfig: remove BE-only platforms from LE kernel build from Boqun Feng
- Refresh ps3_defconfig from Geoff Levand
- Emit GNU & SysV hashes for the vdso from Michael Ellerman
- Define an enum for the bolted SLB indexes from Anshuman Khandual
- Use a local to avoid multiple calls to get_slb_shadow() from Michael Ellerman
- Add gettimeofday() benchmark from Michael Neuling
- Avoid link stack corruption in __get_datapage() from Michael Neuling
- Add virt_to_pfn and use this instead of opencoding from Aneesh Kumar K.V
- Add ppc64le_defconfig from Michael Ellerman
- pseries: extract of_helpers module from Andy Shevchenko
- Correct string length in pseries_of_derive_parent() from Nathan Fontenot
- Free the MSI bitmap if it was slab allocated from Denis Kirjanov
- Shorten irq_chip name for the SIU from Christophe Leroy
- Wait 1s for secondaries to enter OPAL during kexec from Samuel Mendoza-Jonas
- Fix _ALIGN_* errors due to type difference. from Aneesh Kumar K.V
- powerpc/pseries/hvcserver: don't memset pi_buff if it is null from Colin Ian King
- Disable hugepd for 64K page size. from Aneesh Kumar K.V
- Differentiate between hugetlb and THP during page walk from Aneesh Kumar K.V
- Make PCI non-optional for pseries from Michael Ellerman
- Individual System V IPC system calls from Sam bobroff
- Add selftest of unmuxed IPC calls from Michael Ellerman
- discard .exit.data at runtime from Stephen Rothwell
- Delete old orphaned PrPMC 280/2800 DTS and boot file. from Paul Gortmaker
- Use of_get_next_parent to simplify code from Christophe Jaillet
- Paginate some xmon output from Sam bobroff
- Add some more elements to the xmon PACA dump from Michael Ellerman
- Allow the tm-syscall selftest to build with old headers from Michael Ellerman
- Run EBB selftests only on POWER8 from Denis Kirjanov
- Drop CONFIG_TUNE_CELL in favour of CONFIG_CELL_CPU from Michael Ellerman
- Avoid reference to potentially freed memory in prom.c from Christophe Jaillet
- Quieten boot wrapper output with run_cmd from Geoff Levand
- EEH fixes and cleanups from Gavin Shan
- Fix recursive fenced PHB on Broadcom shiner adapter from Gavin Shan
- Use of_get_next_parent() in of_get_ibm_chip_id() from Michael Ellerman
- Fix section mismatch warning in msi_bitmap_alloc() from Denis Kirjanov
- Fix ps3-lpm white space from Rudhresh Kumar J
- Fix ps3-vuart null dereference from Colin King
- nvram: Add missing kfree in error path from Christophe Jaillet
- nvram: Fix function name in some errors messages. from Christophe Jaillet
- drivers/macintosh: adb: fix misleading Kconfig help text from Aaro Koskinen
- agp/uninorth: fix a memleak in create_gatt_table from Denis Kirjanov
- cxl: Free virtual PHB when removing from Andrew Donnellan
- scripts/kconfig/Makefile: Allow KBUILD_DEFCONFIG to be a target from Michael Ellerman
- scripts/kconfig/Makefile: Fix KBUILD_DEFCONFIG check when building with O= from Michael Ellerman
- Freescale updates from Scott: Highlights include 64-bit book3e kexec/kdump
support, a rework of the qoriq clock driver, device tree changes including
qoriq fman nodes, support for a new 85xx board, and some fixes.
- MPC5xxx updates from Anatolij: Highlights include a driver for MPC512x
LocalPlus Bus FIFO with its device tree binding documentation, mpc512x
device tree updates and some minor fixes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=YwcM
-----END PGP SIGNATURE-----
Merge tag 'powerpc-4.4-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc updates from Michael Ellerman:
- Kconfig: remove BE-only platforms from LE kernel build from Boqun
Feng
- Refresh ps3_defconfig from Geoff Levand
- Emit GNU & SysV hashes for the vdso from Michael Ellerman
- Define an enum for the bolted SLB indexes from Anshuman Khandual
- Use a local to avoid multiple calls to get_slb_shadow() from Michael
Ellerman
- Add gettimeofday() benchmark from Michael Neuling
- Avoid link stack corruption in __get_datapage() from Michael Neuling
- Add virt_to_pfn and use this instead of opencoding from Aneesh Kumar
K.V
- Add ppc64le_defconfig from Michael Ellerman
- pseries: extract of_helpers module from Andy Shevchenko
- Correct string length in pseries_of_derive_parent() from Nathan
Fontenot
- Free the MSI bitmap if it was slab allocated from Denis Kirjanov
- Shorten irq_chip name for the SIU from Christophe Leroy
- Wait 1s for secondaries to enter OPAL during kexec from Samuel
Mendoza-Jonas
- Fix _ALIGN_* errors due to type difference, from Aneesh Kumar K.V
- powerpc/pseries/hvcserver: don't memset pi_buff if it is null from
Colin Ian King
- Disable hugepd for 64K page size, from Aneesh Kumar K.V
- Differentiate between hugetlb and THP during page walk from Aneesh
Kumar K.V
- Make PCI non-optional for pseries from Michael Ellerman
- Individual System V IPC system calls from Sam bobroff
- Add selftest of unmuxed IPC calls from Michael Ellerman
- discard .exit.data at runtime from Stephen Rothwell
- Delete old orphaned PrPMC 280/2800 DTS and boot file, from Paul
Gortmaker
- Use of_get_next_parent to simplify code from Christophe Jaillet
- Paginate some xmon output from Sam bobroff
- Add some more elements to the xmon PACA dump from Michael Ellerman
- Allow the tm-syscall selftest to build with old headers from Michael
Ellerman
- Run EBB selftests only on POWER8 from Denis Kirjanov
- Drop CONFIG_TUNE_CELL in favour of CONFIG_CELL_CPU from Michael
Ellerman
- Avoid reference to potentially freed memory in prom.c from Christophe
Jaillet
- Quieten boot wrapper output with run_cmd from Geoff Levand
- EEH fixes and cleanups from Gavin Shan
- Fix recursive fenced PHB on Broadcom shiner adapter from Gavin Shan
- Use of_get_next_parent() in of_get_ibm_chip_id() from Michael
Ellerman
- Fix section mismatch warning in msi_bitmap_alloc() from Denis
Kirjanov
- Fix ps3-lpm white space from Rudhresh Kumar J
- Fix ps3-vuart null dereference from Colin King
- nvram: Add missing kfree in error path from Christophe Jaillet
- nvram: Fix function name in some errors messages, from Christophe
Jaillet
- drivers/macintosh: adb: fix misleading Kconfig help text from Aaro
Koskinen
- agp/uninorth: fix a memleak in create_gatt_table from Denis Kirjanov
- cxl: Free virtual PHB when removing from Andrew Donnellan
- scripts/kconfig/Makefile: Allow KBUILD_DEFCONFIG to be a target from
Michael Ellerman
- scripts/kconfig/Makefile: Fix KBUILD_DEFCONFIG check when building
with O= from Michael Ellerman
- Freescale updates from Scott: Highlights include 64-bit book3e
kexec/kdump support, a rework of the qoriq clock driver, device tree
changes including qoriq fman nodes, support for a new 85xx board, and
some fixes.
- MPC5xxx updates from Anatolij: Highlights include a driver for
MPC512x LocalPlus Bus FIFO with its device tree binding
documentation, mpc512x device tree updates and some minor fixes.
* tag 'powerpc-4.4-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (106 commits)
powerpc/msi: Fix section mismatch warning in msi_bitmap_alloc()
powerpc/prom: Use of_get_next_parent() in of_get_ibm_chip_id()
powerpc/pseries: Correct string length in pseries_of_derive_parent()
powerpc/e6500: hw tablewalk: make sure we invalidate and write to the same tlb entry
powerpc/mpc85xx: Add FSL QorIQ DPAA FMan support to the SoC device tree(s)
powerpc/mpc85xx: Create dts components for the FSL QorIQ DPAA FMan
powerpc/fsl: Add #clock-cells and clockgen label to clockgen nodes
powerpc: handle error case in cpm_muram_alloc()
powerpc: mpic: use IRQCHIP_SKIP_SET_WAKE instead of redundant mpic_irq_set_wake
powerpc/book3e-64: Enable kexec
powerpc/book3e-64/kexec: Set "r4 = 0" when entering spinloop
powerpc/booke: Only use VIRT_PHYS_OFFSET on booke32
powerpc/book3e-64/kexec: Enable SMP release
powerpc/book3e-64/kexec: create an identity TLB mapping
powerpc/book3e-64: Don't limit paca to 256 MiB
powerpc/book3e/kdump: Enable crash_kexec_wait_realmode
powerpc/book3e: support CONFIG_RELOCATABLE
powerpc/booke64: Fix args to copy_and_flush
powerpc/book3e-64: rename interrupt_end_book3e with __end_interrupts
powerpc/e6500: kexec: Handle hardware threads
...
When adding a vPHB in cxl_pci_vphb_add(), we allocate a pci_controller
struct using pcibios_alloc_controller(). However, we don't free it in
cxl_pci_vphb_remove(), causing a leak.
Call pcibios_free_controller() in cxl_pci_vphb_remove() to free the vPHB
data structure correctly.
Signed-off-by: Daniel Axtens <dja@axtens.net>
Signed-off-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The scheduled process area is currently allocated before assigning the
correct maximum processes to the AFU, which will mean we only ever
allocate a fixed number of pages for the scheduled process area. This
will limit us to 958 processes with 2 x 64K pages. If we try to use more
processes than that we'd probably overrun the buffer and corrupt memory
or crash.
AFUs that require three or more interrupts per process will not be
affected as they are already limited to less processes than that, but we
could hit it on an AFU that requires 0, 1 or 2 interrupts per process,
or when using 4K pages.
This patch moves the initialisation of the num_procs to before the SPA
allocation so that enough pages will be allocated for the number of
processes that the AFU supports.
Signed-off-by: Christophe Lombard <clombard@linux.vnet.ibm.com>
Signed-off-by: Ian Munsie <imunsie@au1.ibm.com>
Cc: <stable@vger.kernel.org> # 3.18+
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This works around a pcie host bridge defect on some cards, that can cause
malformed Transaction Layer Packet (TLP) errors to be erroneously reported.
The upper nibble of the vendor section PSL revision is used to distinguish
between different cards. The affected ones have it set to 0.
Signed-off-by: Philippe Bergheaud <felix@linux.vnet.ibm.com>
Acked-by: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
When a context is created via the kernel API, ctx->mapping is allocated
within the kernel and thus needs to be freed when the context is freed.
reclaim_ctx() attempts to do this for contexts with the ctx->kernelapi flag
set, but afu_release() (which can be called from the kernel API through
cxl_fd_release()) sets ctx->mapping to NULL before calling
cxl_context_free() to free the context.
Add a check to afu_release() so that the mappings in contexts created via
the kernel API are left alone so reclaim_ctx() can free them.
Reported-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Fixes: 6f7f0b3df6 ("cxl: Add AFU virtual PHB and kernel API")
Signed-off-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Acked-by: Ian Munsie <imunsie@au1.ibm.com>
Reviewed-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
At present, ctx->irq_bitmap is freed in afu_release_irqs(), which is called
from afu_release() via cxl_context_detach().
Move the freeing of ctx->irq_bitmap from afu_release_irqs() to
reclaim_ctx() (called through cxl_context_free()) so it's freed when
releasing a context via the kernel API (cxl_release_context()) or the
userspace API (afu_release()).
Reported-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Fixes: 6f7f0b3df6 ("cxl: Add AFU virtual PHB and kernel API")
Signed-off-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Acked-by: Ian Munsie <imunsie@au1.ibm.com>
Reviewed-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
cxl_free_afu_irqs() doesn't free IRQ names when it releases an AFU's IRQ
ranges. The userspace API equivalent in afu_release_irqs() calls
afu_irq_name_free() to release the IRQ names.
Call afu_irq_name_free() in cxl_free_afu_irqs() to release the IRQ names.
Make afu_irq_name_free() non-static to allow this.
Reported-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Fixes: 6f7f0b3df6 ("cxl: Add AFU virtual PHB and kernel API")
Signed-off-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Signed-off-by: Ian Munsie <imunsie@au1.ibm.com>
Reviewed-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Presently a lockdep warning is reported during creation of afu_err_buff
bin_attribute for the afu. This is caused due to the variable attr.key
not pointing to a static class key, hence the function lockdep_init_map
reports this warning:
BUG: key <some-address> not in .data!
The patch fixes this issue by calling sysfs_attr_init on the
attr_eb.attr structure before populating it with the afu_err_buff file
details. This will populate the attr.key variable with a static class
key so that lockdep_init_map stops complaining about the lockdep key not
being static.
Reported-by: Daniel Axtens <dja@axtens.net>
Signed-off-by: Vaibhav Jain <vaibhav@linux.vnet.ibm.com>
Acked-by: Ian Munsie <imunsie@au1.ibm.com>
Reviewed-by: Daniel Axtens <dja@axtens.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
A recent change in gcc caused this build failure:
/var/lib/jenkins/workspace/gcc_kernel_build/linux/drivers/misc/cxl/cxl.h:72:27:
error: ‘CXL_PSL_DLCNTL’ defined but not used [-Werror=unused-const-variable]
static const cxl_p1_reg_t CXL_PSL_DLCNTL = {0x0060};
Because of this gcc commit:
Commit 1bca8cbd0c68366f07277f98ce6963e10c2aa617 by mark
PR28901 -Wunused-variable ignores unused const initialised variables in C
12 years ago it was decided that -Wunused-variable shouldn't warn about
static const variables because some code used const static char rcsid[]
strings which were never used but wanted in the code anyway. But as the
bug points out this hides some real bugs. These days the usage of
rcsids is not very popular anymore. So this patch changes the default
to warn about unused static const variables in C with
-Wunused-variable. And it adds a new option -Wno-unused-const-variable
to turn this warning off. For C++ this new warning is off by default,
since const variables can be used as #defines in C++. New testcases for
the new defaults in C and C++ are included testing the new warning and
suppressing it with an unused attribute or using
-Wno-unused-const-variable. gcc/ChangeLog
The cxl driver uses static consts in place of #defines in some cases
for type safety, so this change causes the driver to fail to build on
new copilers as these constants are not all used in every file that
imports the header. Suppress the warning for this driver to return to
the old behaviour of -Wunused-variable.
Reported-by: Anton Blanchard <anton@au1.ibm.com>
Signed-off-by: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Currently the first thing we do in cxl_probe is to grab a reference
on the pci device. Later on, we call device_register on our adapter.
In our remove path, we call device_unregister, but we never call
pci_dev_put. We therefore leak the device every time we do a
reflash.
device_register/unregister is sufficient to hold the reference.
Therefore, drop the call to pci_dev_get.
Here's why this is safe.
The proposed cxl_probe(pdev) calls cxl_adapter_init:
a) init calls cxl_adapter_alloc, which creates a struct cxl,
conventionally called adapter. This struct contains a
device entry, adapter->dev.
b) init calls cxl_configure_adapter, where we set
adapter->dev.parent = &dev->dev (here dev is the pci dev)
So at this point, the cxl adapter's device's parent is the PCI
device that I want to be refcounted properly.
c) init calls cxl_register_adapter
*) cxl_register_adapter calls device_register(&adapter->dev)
So now we're in device_register, where dev is the adapter device, and
we want to know if the PCI device is safe after we return.
device_register(&adapter->dev) calls device_initialize() and then
device_add().
device_add() does a get_device(). device_add() also explicitly grabs
the device's parent, and calls get_device() on it:
parent = get_device(dev->parent);
So therefore, device_register() takes a lock on the parent PCI dev,
which is what pci_dev_get() was guarding. pci_dev_get() can therefore
be safely removed.
Fixes: f204e0b8ce ("cxl: Driver code for powernv PCIe based cards for userspace access")
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Axtens <dja@axtens.net>
Acked-by: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
cxl_pci_enable_device_hook() is called when attempting to enable an AFU
sitting on a vPHB. At present, the state of the underlying CXL card's PCI
channel is only checked when it calls cxl_afu_check_and_enable() at the
very end, after it has already set DMA options and initialised a default
context.
Check the CXL card's link status before setting DMA options or initialising
a default context. If the link is down, print a warning and return
immediately.
Signed-off-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Acked-by: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
- Support "hybrid" iommu/direct DMA ops for coherent_mask < dma_mask from Benjamin Herrenschmidt
- EEH fixes for SRIOV from Gavin
- Introduce rtas_get_sensor_fast() for IRQ handlers from Thomas Huth
- Use hardware RNG for arch_get_random_seed_* not arch_get_random_* from Paul Mackerras
- Seccomp filter support from Michael Ellerman
- opal_cec_reboot2() handling for HMIs & machine checks from Mahesh Salgaonkar
- Add powerpc timebase as a trace clock source from Naveen N. Rao
- Misc cleanups in the xmon, signal & SLB code from Anshuman Khandual
- Add an inline function to update POWER8 HID0 from Gautham R. Shenoy
- Fix pte_pagesize_index() crash on 4K w/64K hash from Michael Ellerman
- Drop support for 64K local store on 4K kernels from Michael Ellerman
- move dma_get_required_mask() from pnv_phb to pci_controller_ops from Andrew Donnellan
- Initialize distance lookup table from drconf path from Nikunj A Dadhania
- Enable RTC class support from Vaibhav Jain
- Disable automatically blocked PCI config from Gavin Shan
- Add LEDs driver for PowerNV platform from Vasant Hegde
- Fix endianness issues in the HVSI driver from Laurent Dufour
- Kexec endian fixes from Samuel Mendoza-Jonas
- Fix corrupted pdn list from Gavin Shan
- Fix fenced PHB caused by eeh_slot_error_detail() from Gavin Shan
- Freescale updates from Scott: Highlights include 32-bit memcpy/memset
optimizations, checksum optimizations, 85xx config fragments and updates,
device tree updates, e6500 fixes for non-SMP, and misc cleanup and minor
fixes.
- A ton of cxl updates & fixes:
- Add explicit precision specifiers from Rasmus Villemoes
- use more common format specifier from Rasmus Villemoes
- Destroy cxl_adapter_idr on module_exit from Johannes Thumshirn
- Destroy afu->contexts_idr on release of an afu from Johannes Thumshirn
- Compile with -Werror from Daniel Axtens
- EEH support from Daniel Axtens
- Plug irq_bitmap getting leaked in cxl_context from Vaibhav Jain
- Add alternate MMIO error handling from Ian Munsie
- Allow release of contexts which have been OPENED but not STARTED from Andrew Donnellan
- Remove use of macro DEFINE_PCI_DEVICE_TABLE from Vaishali Thakkar
- Release irqs if memory allocation fails from Vaibhav Jain
- Remove racy attempt to force EEH invocation in reset from Daniel Axtens
- Fix + cleanup error paths in cxl_dev_context_init from Ian Munsie
- Fix force unmapping mmaps of contexts allocated through the kernel api from Ian Munsie
- Set up and enable PSL Timebase from Philippe Bergheaud
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=n9+X
-----END PGP SIGNATURE-----
Merge tag 'powerpc-4.3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc updates from Michael Ellerman:
- support "hybrid" iommu/direct DMA ops for coherent_mask < dma_mask
from Benjamin Herrenschmidt
- EEH fixes for SRIOV from Gavin
- introduce rtas_get_sensor_fast() for IRQ handlers from Thomas Huth
- use hardware RNG for arch_get_random_seed_* not arch_get_random_*
from Paul Mackerras
- seccomp filter support from Michael Ellerman
- opal_cec_reboot2() handling for HMIs & machine checks from Mahesh
Salgaonkar
- add powerpc timebase as a trace clock source from Naveen N. Rao
- misc cleanups in the xmon, signal & SLB code from Anshuman Khandual
- add an inline function to update POWER8 HID0 from Gautham R. Shenoy
- fix pte_pagesize_index() crash on 4K w/64K hash from Michael Ellerman
- drop support for 64K local store on 4K kernels from Michael Ellerman
- move dma_get_required_mask() from pnv_phb to pci_controller_ops from
Andrew Donnellan
- initialize distance lookup table from drconf path from Nikunj A
Dadhania
- enable RTC class support from Vaibhav Jain
- disable automatically blocked PCI config from Gavin Shan
- add LEDs driver for PowerNV platform from Vasant Hegde
- fix endianness issues in the HVSI driver from Laurent Dufour
- kexec endian fixes from Samuel Mendoza-Jonas
- fix corrupted pdn list from Gavin Shan
- fix fenced PHB caused by eeh_slot_error_detail() from Gavin Shan
- Freescale updates from Scott: Highlights include 32-bit memcpy/memset
optimizations, checksum optimizations, 85xx config fragments and
updates, device tree updates, e6500 fixes for non-SMP, and misc
cleanup and minor fixes.
- a ton of cxl updates & fixes:
- add explicit precision specifiers from Rasmus Villemoes
- use more common format specifier from Rasmus Villemoes
- destroy cxl_adapter_idr on module_exit from Johannes Thumshirn
- destroy afu->contexts_idr on release of an afu from Johannes
Thumshirn
- compile with -Werror from Daniel Axtens
- EEH support from Daniel Axtens
- plug irq_bitmap getting leaked in cxl_context from Vaibhav Jain
- add alternate MMIO error handling from Ian Munsie
- allow release of contexts which have been OPENED but not STARTED
from Andrew Donnellan
- remove use of macro DEFINE_PCI_DEVICE_TABLE from Vaishali Thakkar
- release irqs if memory allocation fails from Vaibhav Jain
- remove racy attempt to force EEH invocation in reset from Daniel
Axtens
- fix + cleanup error paths in cxl_dev_context_init from Ian Munsie
- fix force unmapping mmaps of contexts allocated through the kernel
api from Ian Munsie
- set up and enable PSL Timebase from Philippe Bergheaud
* tag 'powerpc-4.3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (140 commits)
cxl: Set up and enable PSL Timebase
cxl: Fix force unmapping mmaps of contexts allocated through the kernel api
cxl: Fix + cleanup error paths in cxl_dev_context_init
powerpc/eeh: Fix fenced PHB caused by eeh_slot_error_detail()
powerpc/pseries: Cleanup on pci_dn_reconfig_notifier()
powerpc/pseries: Fix corrupted pdn list
powerpc/powernv: Enable LEDS support
powerpc/iommu: Set default DMA offset in dma_dev_setup
cxl: Remove racy attempt to force EEH invocation in reset
cxl: Release irqs if memory allocation fails
cxl: Remove use of macro DEFINE_PCI_DEVICE_TABLE
powerpc/powernv: Fix mis-merge of OPAL support for LEDS driver
powerpc/powernv: Reset HILE before kexec_sequence()
powerpc/kexec: Reset secondary cpu endianness before kexec
powerpc/hvsi: Fix endianness issues in the HVSI driver
leds/powernv: Add driver for PowerNV platform
powerpc/powernv: Create LED platform device
powerpc/powernv: Add OPAL interfaces for accessing and modifying system LED states
powerpc/powernv: Fix the log message when disabling VF
cxl: Allow release of contexts which have been OPENED but not STARTED
...
This patch configures the PSL Timebase function and enables it,
after the CAPP has been initialized by OPAL.
Acked-by: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Philippe Bergheaud <felix@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The cxl user api uses the address_space associated with the file when we
need to force unmap all cxl mmap regions (e.g. on eeh, driver detach,
etc). Currently, contexts allocated through the kernel api do not do
this and instead skip the mmap invalidation, potentially allowing them
to poke at the hardware after such an event, which may cause all sorts
of trouble.
This patch allocates an address_space for cxl contexts allocated through
the kernel api so that the same invalidate path will for these contexts
as well. We don't use the anonymous inode's address_space, as doing so
could invalidate any mmaps of completely unrelated drivers using
anonymous file descriptors.
This patch also introduces a kernelapi flag, so we know when freeing the
context if the address_space was allocated by us and needs to be freed.
Signed-off-by: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
If the cxl_context_alloc() call fails, we return immediately without
releasing the reference on the AFU device, allowing it to leak.
This patch switches to using goto style error handling so that the
device is released in common code for both error paths, and will also
simplify things if we add additional initialisation in this function in
the future.
Signed-off-by: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
cxl_reset currently PERSTs the slot, and then repeatedly tries to
read MMIO space in order to kick off EEH.
There are 2 problems with this: it's unnecessary, and it's racy.
It's unnecessary because the PERST will bring down the PHB link.
That will be picked up by the CAPP, which will send out an HMI.
Skiboot, noticing an HMI from the CAPP, will send an OPAL
notification to the kernel, which will trigger EEH recovery.
It's also racy: the EEH recovery triggered by the CAPP will
eventually cause the MMIO space to have its mapping invalidated
and the pointer NULLed out. This races with our attempt to read
the MMIO space. This is causing OOPSes in testing.
Simply drop all the attempts to force EEH detection, and trust
that Skiboot will send the notification and that we'll act on it.
The Skiboot code to send the EEH notification has been in Skiboot
for as long as CAPP recovery has been supported, so we don't need
to worry about breaking obscure setups with ancient firmware.
Cc: Ryan Grimm <grimm@linux.vnet.ibm.com>
Cc: stable@vger.kernel.org
Fixes: 62fa19d4b4 ("cxl: Add ability to reset the card")
Signed-off-by: Daniel Axtens <dja@axtens.net>
Acked-by: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This minor patch plugs a potential irq leak in case of a memory
allocation failure inside function the afu_allocate_irqs. Presently the
irqs allocated to the context gets leaked if allocation of either
one of context irq_bitmap or irq_names fails.
Signed-off-by: Vaibhav Jain <vaibhav@linux.vnet.ibm.com>
Acked-by: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Macro DEFINE_PCI_DEVICE_TABLE is deprecated. So, here use
struct pci_device_id instead of DEFINE_PCI_DEVICE_TABLE with
the goal of getting rid of this macro completely.
The Coccinelle semantic patch that performs this transformation
is as follows:
@@
identifier a;
declarer name DEFINE_PCI_DEVICE_TABLE;
initializer i;
@@
- DEFINE_PCI_DEVICE_TABLE(a)
+ const struct pci_device_id a[]
= i;
Signed-off-by: Vaishali Thakkar <vthakkar1994@gmail.com>
Acked-by: Michael Neuling <mikey@neuling.org>
Acked-by: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
If we open a context but do not start it (either because we do not attempt
to start it, or because it fails to start for some reason), we are left
with a context in state OPENED. Previously, cxl_release_context() only
allowed releasing contexts in state CLOSED, so attempting to release an
OPENED context would fail.
In particular, this bug causes available contexts to run out after some EEH
failures, where drivers attempt to release contexts that have failed to
start.
Allow releasing contexts in any state with a value lower than STARTED, i.e.
OPENED or CLOSED (we can't release a STARTED context as it's currently
using the hardware, and we assume that contexts in any new states which may
be added in future with a value higher than STARTED are also unsafe to
release).
Cc: stable@vger.kernel.org
Fixes: 6f7f0b3df6 ("cxl: Add AFU virtual PHB and kernel API")
Signed-off-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Signed-off-by: Daniel Axtens <dja@axtens.net>
Acked-by: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
userspace programs using cxl currently have to use two strategies for
dealing with MMIO errors simultaneously. They have to check every read
for a return of all Fs in case the adapter has gone away and the kernel
has not yet noticed, and they have to deal with SIGBUS in case the
kernel has already noticed, invalidated the mapping and marked the
context as failed.
In order to simplify things, this patch adds an alternative approach
where the kernel will return a page filled with Fs instead of delivering
a SIGBUS. This allows userspace to only need to deal with one of these
two error paths, and is intended for use in libraries that use cxl
transparently and may not be able to safely install a signal handler.
This approach will only work if certain constraints are met. Namely, if
the application is both reading and writing to an address in the problem
state area it cannot assume that a non-FF read is OK, as it may just be
reading out a value it has previously written. Further - since only one
page is used per context a write to a given offset would be visible when
reading the same offset from a different page in the mapping (this only
applies within a single context, not between contexts).
An application could deal with this by e.g. making sure it also reads
from a read-only offset after any reads to a read/write offset.
Due to these constraints, this functionality must be explicitly
requested by userspace when starting the context by passing in the
CXL_START_WORK_ERR_FF flag.
Signed-off-by: Ian Munsie <imunsie@au1.ibm.com>
Acked-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This patch plugs the leak of irq_bitmap, allocated as part of
initialization of cxl_context struct; during the call to
afu_allocate_irqs. The bitmap is now release during the call to function
afu_release_irqs.
Reported-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Signed-off-by: Vaibhav Jain <vaibhav@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
CONFIG_CXL_EEH is for CXL's EEH related code.
Other drivers can depend on or #ifdef on this symbol to configure
PERST behaviour, allowing CXL to participate in the EEH process.
Reviewed-by: Cyril Bur <cyrilbur@gmail.com>
Signed-off-by: Daniel Axtens <dja@axtens.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
EEH (Enhanced Error Handling) allows a driver to recover from the
temporary failure of an attached PCI card. Enable basic CXL support
for EEH.
Signed-off-by: Daniel Axtens <dja@axtens.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Provide a kernel API and a sysfs entry which allow a user to specify
that when a card is PERSTed, it's image will stay the same, allowing
it to participate in EEH.
cxl_reset is used to reflash the card. In that case, we cannot safely
assert that the image will not change. Therefore, disallow cxl_reset
if the flag is set.
Signed-off-by: Daniel Axtens <dja@axtens.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
If the driver doesn't participate in EEH, the AFUs will be removed
by cxl_remove, which will be invoked by EEH.
If the driver does particpate in EEH, the vPHB needs to stick around
so that the it can particpate.
In both cases, we shouldn't remove the AFU/vPHB.
Reviewed-by: Cyril Bur <cyrilbur@gmail.com>
Signed-off-by: Daniel Axtens <dja@axtens.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
As with an adapter, some aspects of initialisation are done only once
in the lifetime of an AFU: for example, allocating memory, or setting
up sysfs/debugfs files.
However, we may want to be able to do some parts of the initialisation
multiple times: for example, in error recovery we want to be able to
tear down and then re-map IO memory and IRQs.
Therefore, refactor AFU init/teardown as follows.
- Create two new functions: 'cxl_configure_afu', and its pair
'cxl_deconfigure_afu'. As with the adapter functions,
these (de)configure resources that do not need to last the entire
lifetime of the AFU.
- Allocating and releasing memory remain the task of 'cxl_alloc_afu'
and 'cxl_release_afu'.
- Once-only functions that do not involve allocating/releasing memory
stay in the overarching 'cxl_init_afu'/'cxl_remove_afu' pair.
However, the task of picking an AFU mode and activating it has been
broken out.
Signed-off-by: Daniel Axtens <dja@axtens.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Some aspects of initialisation are done only once in the lifetime of
an adapter: for example, allocating memory for the adapter,
allocating the adapter number, or setting up sysfs/debugfs files.
However, we may want to be able to do some parts of the
initialisation multiple times: for example, in error recovery we
want to be able to tear down and then re-map IO memory and IRQs.
Therefore, refactor CXL init/teardown as follows.
- Keep the overarching functions 'cxl_init_adapter' and its pair,
'cxl_remove_adapter'.
- Move all 'once only' allocation/freeing steps to the existing
'cxl_alloc_adapter' function, and its pair 'cxl_release_adapter'
(This involves moving allocation of the adapter number out of
cxl_init_adapter.)
- Create two new functions: 'cxl_configure_adapter', and its pair
'cxl_deconfigure_adapter'. These two functions 'wire up' the
hardware --- they (de)configure resources that do not need to
last the entire lifetime of the adapter
Signed-off-by: Daniel Axtens <dja@axtens.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
- MMIO pointer unmapping is guarded by a null pointer check.
However, iounmap doesn't null the pointer, just invalidate it.
Therefore, explicitly null the pointer after unmapping.
- afu_desc_mmio also needs to be unmapped.
- PCI regions are allocated in cxl_map_adapter_regs.
Therefore they should be released in unmap, not elsewhere.
Acked-by: Cyril Bur <cyrilbur@gmail.com>
Signed-off-by: Daniel Axtens <dja@axtens.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Check if an IRQ is mapped before releasing it.
This will simplify future EEH code by allowing unconditional unmapping
of IRQs.
Acked-by: Cyril Bur <cyrilbur@gmail.com>
Signed-off-by: Daniel Axtens <dja@axtens.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Previously the SPA was allocated and freed upon entering and leaving
AFU-directed mode. This causes some issues for error recovery - contexts
hold a pointer inside the SPA, and they may persist after the AFU has
been detached.
We would ideally like to allocate the SPA when the AFU is allocated, and
release it until the AFU is released. However, we don't know how big the
SPA needs to be until we read the AFU descriptor.
Therefore, restructure the code:
- Allocate the SPA only once, on the first attach.
- Release the SPA only when the entire AFU is being released (not
detached). Guard the release with a NULL check, so we don't free
if it was never allocated (e.g. dedicated mode)
Acked-by: Cyril Bur <cyrilbur@gmail.com>
Signed-off-by: Daniel Axtens <dja@axtens.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
If the PCI channel has gone down, don't attempt to poke the hardware.
We need to guard every time cxl_whatever_(read|write) is called. This
is because a call to those functions will dereference an offset into an
mmio register, and the mmio mappings get invalidated in the EEH
teardown.
Check in the read/write functions in the header.
We give them the same semantics as usual PCI operations:
- a write to a channel that is down is ignored.
- a read from a channel that is down returns all fs.
Also, we try to access the MMIO space of a vPHB device as part of the
PCI disable path. Because that's a read that bypasses most of our usual
checks, we handle it explicitly.
As far as user visible warnings go:
- Check link state in file ops, return -EIO if down.
- Be reasonably quiet if there's an error in a teardown path,
or when we already know the hardware is going down.
- Throw a big WARN if someone tries to start a CXL operation
while the card is down. This gives a useful stacktrace for
debugging whatever is doing that.
Signed-off-by: Daniel Axtens <dja@axtens.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
We're about to make these more complex, so make them functions
first.
Signed-off-by: Daniel Axtens <dja@axtens.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Vaibhav Jain
Matthew R. Ochs
Christophe Lombard
Masanari Iida
Ingo Molnar
Linus Torvalds
Dave Jiang
Andrew Donnellan
Greg Kurz
Jan Kara
Geliang Tang
Frederic Barrat
Christophe Jaillet
Ian Munsie
Wei Yongjun
Philippe Bergheaud
Paul Gortmaker
Michael Neuling
Aneesh Kumar K.V
Markus Elfring
Geliang Tang
Bjorn Helgaas
Uma Krishnan
Brian Norris
Daniel Axtens
Vaishali Thakkar