This includes following Thunderbolt/USB4 changes for v5.10 merge window:
* A couple of optimizations around Tiger Lake force power logic and
NHI (Native Host Interface) LC (Link Controller) mailbox command
processing
* Power management improvements for Software Connection Manager
* Debugfs support
* Allow KUnit tests to be enabled also when Thunderbolt driver is
configured as module.
* Few minor cleanups and fixes
All these have been in linux-next with no reported issues.
-----BEGIN PGP SIGNATURE-----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=KvWM
-----END PGP SIGNATURE-----
Merge tag 'thunderbolt-for-v5.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/westeri/thunderbolt into usb-next
Mika writes:
thunderbolt: Changes for v5.10 merge window
This includes following Thunderbolt/USB4 changes for v5.10 merge window:
* A couple of optimizations around Tiger Lake force power logic and
NHI (Native Host Interface) LC (Link Controller) mailbox command
processing
* Power management improvements for Software Connection Manager
* Debugfs support
* Allow KUnit tests to be enabled also when Thunderbolt driver is
configured as module.
* Few minor cleanups and fixes
All these have been in linux-next with no reported issues.
* tag 'thunderbolt-for-v5.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/westeri/thunderbolt: (37 commits)
thunderbolt: Capitalize comment on top of QUIRK_FORCE_POWER_LINK_CONTROLLER
thunderbolt: Correct tb_check_quirks() kernel-doc
thunderbolt: Log correct zeroX entries in decode_error()
thunderbolt: Handle ERR_LOCK notification
thunderbolt: Use "if USB4" instead of "depends on" in Kconfig
thunderbolt: Allow KUnit tests to be built also when CONFIG_USB4=m
thunderbolt: Only stop control channel when entering freeze
thunderbolt: debugfs: Fix uninitialized return in counters_write()
thunderbolt: Add debugfs interface
thunderbolt: No need to warn in TB_CFG_ERROR_INVALID_CONFIG_SPACE
thunderbolt: Introduce tb_switch_is_tiger_lake()
thunderbolt: Introduce tb_switch_is_ice_lake()
thunderbolt: Check for Intel vendor ID when identifying controller
thunderbolt: Introduce tb_port_is_nhi()
thunderbolt: Introduce tb_switch_next_cap()
thunderbolt: Introduce tb_port_next_cap()
thunderbolt: Move struct tb_cap_any to tb_regs.h
thunderbolt: Add runtime PM for Software CM
thunderbolt: Create device links from ACPI description
ACPI: Export acpi_get_first_physical_node() to modules
...
There was copy & paste error so it always printed value of pkg->zero1.
Also use tb_ctl_warn() here, no need to print backtrace.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
If the USB4 router downstream port is locked, sending configuration
packet to a router below it causes ERR_LOCK to be sent. Instead of warn
splat about unknown error we log the error (just warning level) and
return -EACCESS instead. The idea is that we may want to do something
when such error code is received, like perform unlock.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
This groups the USB4 options more nicely, and also does not require that
every config option lists explicit depends on USB4.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
This adds a bit more build coverage for the tests even though these are
not expected to be enabled by normal users and distros. In order to make
this working we need to open-code kunit_test_suite() and call the
relevant functions directly in the driver init/exit hook.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
According to the kernel power management documentation freeze phase
should only quiesce the device, no need to configure wakes or put it to
low power state. For this reason we simply stop the control channel and
in case of Software Connection Manager also mark the hotplug disabled.
This should align the driver better with the PM framework expectations.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
One more fix that makes ASUS PA27AC Thunderbolt 3 monitor work more
reliably.
This has been in linux-next with no reported issues.
-----BEGIN PGP SIGNATURE-----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=sgTO
-----END PGP SIGNATURE-----
Merge tag 'thunderbolt-for-v5.9-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/westeri/thunderbolt into usb-linus
Mika writes:
thunderbolt: Fix for v5.9-rc6
One more fix that makes ASUS PA27AC Thunderbolt 3 monitor work more
reliably.
This has been in linux-next with no reported issues.
* tag 'thunderbolt-for-v5.9-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/westeri/thunderbolt:
thunderbolt: Retry DROM read once if parsing fails
If the first line is in an invalid format then the "ret" value is
uninitialized. We should return -EINVAL instead.
Fixes: 54e418106c ("thunderbolt: Add debugfs interface")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Kai-Heng reported that sometimes DROM parsing of ASUS PA27AC Thunderbolt 3
monitor fails. This makes the driver to fail to add the device so only
DisplayPort tunneling is functional.
It is not clear what exactly happens but waiting for 100 ms and retrying
the read seems to work this around so we do that here.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=206493
Reported-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Tested-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Cc: stable@vger.kernel.org
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
This adds debugfs interface that can be used for debugging possible
issues in hardware/software. It exposes router and adapter config spaces
through files like this:
/sys/kernel/debug/thunderbolt/<DEVICE>/regs
/sys/kernel/debug/thunderbolt/<DEVICE>/<PORT1>/regs
/sys/kernel/debug/thunderbolt/<DEVICE>/<PORT1>/path
/sys/kernel/debug/thunderbolt/<DEVICE>/<PORT1>/counters
/sys/kernel/debug/thunderbolt/<DEVICE>/<PORT2>/regs
/sys/kernel/debug/thunderbolt/<DEVICE>/<PORT2>/path
/sys/kernel/debug/thunderbolt/<DEVICE>/<PORT2>/counters
...
The "regs" is either the router or port configuration space register
dump. The "path" is the port path configuration space and "counters" is
the optional counters configuration space.
These files contains one register per line so it should be easy to use
normal filtering tools to find the registers of interest if needed.
The router and adapter regs file becomes writable when
CONFIG_USB4_DEBUGFS_WRITE is enabled (which is not supposed to be done
in production systems) and in this case the developer can write "offset
value" lines there to modify the hardware directly. For convenience this
also supports the long format the read side produces (but ignores the
additional fields). The counters file can be written even when
CONFIG_USB4_DEBUGFS_WRITE is not enabled and it is only used to clear
the counter values.
Signed-off-by: Gil Fine <gil.fine@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This may be returned for example when accessing some of the vendor
specific capabilities. It is not fatal by any means so instead of WARN()
just log it as debug level. The caller gets error back anyway and is
expected to handle it accordingly.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is needed to differentiate Tiger Lake from other controllers.
Signed-off-by: Gil Fine <gil.fine@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is needed to differentiate Ice Lake from other controllers.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With USB4 there will be other vendors so make sure the current checks
for different Intel controllers will not accidentally match those.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is useful if one needs to check if adapter (port) is the host
interface (NHI). Make tb_port_alloc_hopid() take advantage of this.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is similar to tb_port_next_cap() but instead allows walking
capability list of a switch (router). Convert tb_switch_find_cap() and
tb_switch_find_vse_cap() to use this as well.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This function is useful for walking port config space (adapter)
capability lists. Convert the tb_port_find_cap() to use this as well.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This structure will be needed by the debugfs implementation so make it
available outside of cap.c.
While there add kernel-doc comments to the structure.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This adds runtime PM support for the Software Connection Manager parts
of the driver. This allows to save power when either there is no device
attached at all or there is a device attached and all following
conditions are true:
- Tunneled PCIe root/downstream ports are runtime suspended
- Tunneled USB3 ports are runtime suspended
- No active DisplayPort stream
- No active XDomain connection
For the first two we take advantage of device links that were added in
previous patch. Difference for the system sleep case is that we also
enable wakes when something is geting plugged in/out of the Thunderbolt
ports.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
The new way to describe relationship between tunneled ports and USB4 NHI
(Native Host Interface) is with ACPI _DSD looking like below for a PCIe
downstream port:
Scope (\_SB.PCI0)
{
Device (NHI0) { } // Thunderbolt NHI
Device (DSB0) // Hotplug downstream port
{
Name (_DSD, Package () {
ToUUID("daffd814-6eba-4d8c-8a91-bc9bbf4aa301"),
Package () {
Package () {"usb4-host-interface", \_SB.PCI0.NHI0},
...
}
})
}
}
This is "documented" in these [1] USB-IF slides and being used on
systems that ship with Windows.
The _DSD can be added to tunneled USB3 and PCIe ports, and is needed to
make sure the USB4 NHI is resumed before any of the tunneled ports so
the protocol tunnels get established properly before the actual port
itself is resumed. Othwerwise the USB/PCI core find the link may not be
established and starts tearing down the device stack.
This parses the ACPI description each time NHI is probed and tries to
find devices that has the property and it references the NHI in
question. For each matching device a device link from that device to the
NHI is created.
Since USB3 ports themselves do not get runtime suspended with the parent
device (hub) we do not add the link from the USB3 port to USB4 NHI but
instead we add the link from the xHCI device. This makes the device link
usable for runtime PM as well.
[1] https://www.usb.org/sites/default/files/D1T2-2%20-%20USB4%20on%20Windows.pdf
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
On older Apple systems there is currently a PCI quirk in place to block
resume of tunneled PCIe ports until NHI (Thunderbolt controller) is
resumed. This makes sure the PCIe tunnels are re-established before PCI
core notices it.
With device links the same thing can be done without quirks. The driver
core will make sure the supplier (NHI) is resumed before consumers (PCIe
downstream ports).
For this reason switch the Thunderbolt driver to use device links and
remove the PCI quirk.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
In order for the router and the whole domain to wake up from system
suspend states we need to enable wakes for the connected routers. For
device routers we enable wakes from PCIe and USB 3.x. This allows
devices such as keyboards connected to USB 3.x hub that is tunneled to
wake the system up as expected. For all routers we enabled wake on USB4
for each connected ports. This is used to propagate the wake from router
to another.
Do the same for legacy routers through link controller vendor specific
registers as documented in USB4 spec chapter 13.
While there correct kernel-doc of usb4_switch_set_sleep() -- it does not
enable wakes instead there is a separate function (usb4_switch_set_wake())
that does.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
USB4 spec mandates that the lane 1 should be disabled if lanes are not
bonded. For host-to-host connections (XDomain) we don't support lane
bonding so in order to be compatible with the spec, disable lane 1 when
another host is connected.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
When the port is connected to another host it should be marked as such
in the USB4 port capability. This information is used by the router
during sleep and wakeup.
Also do the same for legacy switches via link controller vendor specific
registers.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Both ends of the link needs to have this set. Otherwise the link is not
re-established properly after sleep. Now since it is possible to have
mixed USB4 and Thunderbolt 1, 2 and 3 devices we need to split the link
configuration functionality to happen per port so we can pick the
correct implementation.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
During testing it was noticed that the link is not properly restored
after the domain exits sleep if the link configured bits are set before
lane bonding is enabled. The USB4 spec does not say in which order these
need to be set but setting link configured afterwards makes the link
restoration work so we do that instead.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Some early stage USB4 devices do not like that any of the enumerating
router config space fields (ROUTER_CS_1 - ROUTER_CS_4) are written after
the initial enumeration for example when entering sleep states. The
default timeout by the USB4 spec is 10 ms which should be fine for the
driver to handle.
For this reason do not change the notification timeout from the default
10 ms for USB4 routers.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
The TMU will be reset after router exits sleep so in order to
re-configure it upon resume make sure the structure is initialized again
based on the current hardware state.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
DP tunnels do not need the same kind of treatment as others because they
are created based on hot-plug events on DP adapter ports, and the
display stack does not need the tunnels to be enabled when resuming from
suspend. Also Tiger Lake Thunderbolt controller sends unplug event on D3
exit so this avoids that as well.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
First generation routers may need the reset command upon resume but it
is not supported by newer generations.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
USB4 spec says that NFC buffers field is not used for protocol adapters,
only for lane adapters so make tb_port_add_nfc_credits() skip non-lane
adapters in order to follow the spec.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
In Tiger Lake the Firmware CM is always enabled (so bit 0 is always set)
but it may be in "pass through" mode which means it requires Software CM
instead. This can be determined by checking bit 31 instead.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
When Software CM is running it should not send any NHI mailbox command
during PM flows. Only force power bit needs to be set and cleared so
change Tiger Lake (well and Ice Lake) nhi_ops to take this into account.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Currently the Ice Lake and Tiger Lake NHI (host controller) LC (link
controller) mailbox command processing checks for the completion of
command every 100 msecs. These controllers are found to complete this in
the order of 1 ms or so. Since this delay is in suspend path, surplus
delay is effectively affecting runtime PM suspend flows.
Optimize this so that we do the wait for 1 ms after reading the mailbox
register. This should make Ice Lake and Tiger Lake runtime suspend take
less time to complete.
Reported-by: Dana Alkattan <dana.alkattan@intel.com>
Signed-off-by: Rajmohan Mani <rajmohan.mani@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Currently the "Force Power" logic uses 10 retries, each with a delay of
250 ms. Thunderbolt controllers in Ice Lake and Tiger Lake platforms are
found to complete this in the order of 3 ms or so. Since this delay
is in resume path, surplus delay is effectively affecting runtime PM
resume flows.
Decrease the granularity of the delay to 3 ms and increase the number of
retries so we wait maximum of ~1 s which is the recommended timeout.
This should make runtime resume a bit faster.
Reported-by: Dana Alkattan <dana.alkattan@intel.com>
Signed-off-by: Rajmohan Mani <rajmohan.mani@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Doesn't really matter for an individual driver, but it may
get coppied to lots more. I consider it's a little tidy up.
Signed-off-by: Tian Tao <tiantao6@hisilicon.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
This includes two fixes, one that fixes a regression around reboot and
other that uses a correct link rate when USB3 bandwidth is reclaimed
when the link is not up.
Both have been in linux-next with no reported issues.
-----BEGIN PGP SIGNATURE-----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=vxwa
-----END PGP SIGNATURE-----
Merge tag 'thunderbolt-for-v5.9-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/westeri/thunderbolt into usb-linus
Mika writes:
thunderbolt: Fixes for v5.9-rc4
This includes two fixes, one that fixes a regression around reboot and
other that uses a correct link rate when USB3 bandwidth is reclaimed
when the link is not up.
Both have been in linux-next with no reported issues.
* tag 'thunderbolt-for-v5.9-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/westeri/thunderbolt:
thunderbolt: Use maximum USB3 link rate when reclaiming if link is not up
thunderbolt: Disable ports that are not implemented
If the USB3 link is not up the actual link rate is 0 so when reclaiming
bandwidth we should look at maximum supported link rate instead.
Cc: stable@vger.kernel.org
Fixes: 0bd680cd90 ("thunderbolt: Add USB3 bandwidth management")
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Commit 4caf2511ec ("thunderbolt: Add trivial .shutdown") exposes a bug
in the Thunderbolt driver, that frees an unallocated id, resulting in the
following spinlock bad magic bug.
[ 20.633803] BUG: spinlock bad magic on CPU#4, halt/3313
[ 20.640030] lock: 0xffff92e6ad5c97e0, .magic: 00000000, .owner: <none>/-1, .owner_cpu: 0
[ 20.672139] Call Trace:
[ 20.675032] dump_stack+0x97/0xdb
[ 20.678950] ? spin_bug+0xa5/0xb0
[ 20.682865] do_raw_spin_lock+0x68/0x98
[ 20.687397] _raw_spin_lock_irqsave+0x3f/0x5d
[ 20.692535] ida_destroy+0x4f/0x124
[ 20.696657] tb_switch_release+0x6d/0xfd
[ 20.701295] device_release+0x2c/0x7d
[ 20.705622] kobject_put+0x8e/0xac
[ 20.709637] tb_stop+0x55/0x66
[ 20.713243] tb_domain_remove+0x36/0x62
[ 20.717774] nhi_remove+0x4d/0x58
Fix the issue by disabling ports that are enabled as per the EEPROM, but
not implemented. While at it, update the kernel doc for the disabled
field, to reflect this.
Cc: stable@vger.kernel.org
Fixes: 4caf2511ec ("thunderbolt: Add trivial .shutdown")
Reported-by: Srikanth Nandamuri <srikanth.nandamuri@intel.com>
Signed-off-by: Nikunj A. Dadhania <nikunj.dadhania@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Some external devices can support completing thunderbolt authentication
when they are unplugged. For this to work though, the link controller must
remain operational.
The only device known to support this right now is the Dell WD19TB, so add
a quirk for this.
Signed-off-by: Mario Limonciello <mario.limonciello@dell.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
This allows userspace to have a shorter period of time that the device
is unusable and to call it at a more convenient time.
For example flushing the image may happen while the user is using the
machine and authenticating/rebooting may happen while logging out.
Signed-off-by: Mario Limonciello <mario.limonciello@dell.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
The 32 bit int value 512 is being left shifted and then used in a context
that expects the expression to be a larger unsigned long. There may be
a potential integer overflow, so make 512 a UL before shift to avoid
any such issues.
Addresses-Coverity: ("Uninintentional integer overflow")
Fixes: 3b1d8d577c ("thunderbolt: Implement USB3 bandwidth negotiation routines")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
USB4 spec specifies standard access to retimers (both on-board and
cable) through USB4 port sideband access. This makes it possible to
upgrade their firmware in the same way than we already do with the
routers.
This enumerates on-board retimers under each USB4 port when the link
comes up and adds them to the bus under the router the retimer belongs
to. Retimers are exposed in sysfs with name like <device>:<port>.<index>
where device is the router the retimer belongs to, port is the USB4 port
the retimer is connected to and index is the retimer index under that
port (starting from 1). This applies to the upstream USB4 port as well
so if there is on-board retimer between the port and the router it is
also added accordingly.
At this time we do not add cable retimers but there is no techincal
restriction to do so in the future if needed. It is not clear whether it
makes sense to upgrade their firmwares and at least Thunderbolt 3 cables
it has not been done outside of lab environments.
The sysfs interface is made to follow the router NVM upgrade to make it
easy to extend the existing userspace (fwupd) to handle these as well.
Signed-off-by: Kranthi Kuntala <kranthi.kuntala@intel.com>
Co-developed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
USB4 spec specifies standard set of sideband operations that are send
over the low speed link to access either retimers on the link or the
link parter (the other router). The USB4 retimer spec extends these and
adds operations for retimer NVM upgrade.
This implements the retimer access and NVM upgrade USB4 port sideband
operations which we need for retimer support in the patch that follows.
Signed-off-by: Rajmohan Mani <rajmohan.mani@intel.com>
Co-developed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Greg Kroah-Hartman
Mika Westerberg
Dan Carpenter
Gil Fine
Rajmohan Mani
Tian Tao
Nikunj A. Dadhania
Gustavo A. R. Silva
Stephen Rothwell
Wei Yongjun
Mario Limonciello
Colin Ian King
Kranthi Kuntala