because of using the same function get_ethernet_addr as cdc_ether.c
i export usbnet_get_ethernet_addr from usbnet and fixed cdc_ether
(suggested by Oliver Neukum).
Signed-off-by: Peter Holik <peter@holik.at>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch updates the tg3 version to 3.99.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After a shutdown reset, the LAA needs to be restored before posting the
post-reset signature in shared memory. If the LAA is not restored
before then, the bootcode will assume the factory default MAC address
and WOL will not work with the LAA.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch restricts the CLKREQ bugfix to the A0 and A1 revisions
of 57780 ASIC rev chips.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 5761 WOL and LED fixes used the PCI device ID to as the activation
key. The 5761S requires the same process.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On rare occasions, send BD corruptions can occur. This patch
fixes the problem by increasing the L1 entry threshold to 4
milliseconds.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some 57780 ASIC revision parts do not have NVRAM. Code the driver so
that it is tolerant of this configuration.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The tg3 driver's ISR is coded to accept interrupts as its own if the
status block tag does not equal the last tag the driver has seen. The
last_tag field is updated from tg3_poll. In a screaming interrupt
situation from another device sharing tg3's IRQ, tg3_poll does not get
a chance to be called, so the last_tag will always be out of sync with
the status block tag. Consequently, the driver will continually
declare the screaming interrupts as its own, thus thwarting the
screaming interrupt detection logic.
This patch solves the problem by creating a new last_irq_tag member and
recording the status block tag in the ISR. The ISR then checks the
last_irq_tag for interrupt ownership.
Many thanks to John Marvin for the detailed bug report and analysis and
Michael Chan for the bugfix.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Tested-by: John Marvin <jsm@fc.hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The recent NVRAM patches sanitized how the driver deals with NVRAM
data, but they failed to bring the SEEPROM interfaces inline with
the new strategy. This patch brings the SEEPROM interfaces up to date.
This patch also reverts commit 0d489ffb76
("tg3: fix big endian MAC address collection failure").
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Tested-by: Robin Holt <holt@sgi.com>
Tested-by: James Bottomley <james.bottomley@HansenPartnership.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes a hang on resume when the filesystem is not
available and request_firmware blocks.
However, the device does not accept the firmware on resume.
and it will exit with:
> firmware part 1 upload failed (-71).
> device is in a bad state. please reconnect it!
Reported-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
swap mwl8k_remove and mwl8k_shutdown functions to allow
"rmmod mwl8k; modprobe mwl8k"
Signed-off-by: Joerg Albert <jal2@gmx.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch deactivates powersave in station mode.
It does not work correctly yet, so the code does more harm than good.
Reported-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
After suspend & resume the rt2x00 devices won't wakeup
anymore due to a broken register information setup.
The most important problem is the release of the EEPROM
buffer which is completely cleared and never read again
after the suspend.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As the sk_sleep wait queue actually lives in tfile, which may be
detached from the tun device, bad things will happen when we use
sk_sleep after detaching.
Since the tun device is the persistent data structure here (when
requested by the user), it makes much more sense to have the wait
queue live there. There is no reason to have it in tfile at all
since the only time we can wait is if we have a tun attached.
In fact we already have a wait queue in tun_struct, so we might
as well use it.
Reported-by: Eric W. Biederman <ebiederm@xmission.com>
Tested-by: Christian Borntraeger <borntraeger@de.ibm.com>
Tested-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The commit c70f182940 ("tun: Fix
races between tun_net_close and free_netdev") fixed a race where
an asynchronous deletion of a tun device can hose a poll(2) on
a tun fd attached to that device.
However, this came at the cost of moving the tun wait queue into
the tun file data structure. The problem with this is that it
imposes restrictions on when and where the tun device can access
the wait queue since the tun file may change at any time due to
detaching and reattaching.
In particular, now that we need to use the wait queue on the
receive path it becomes difficult to properly synchronise this
with the detachment of the tun device.
This patch solves the original race in a different way. Since
the race is only because the underlying memory gets freed, we
can prevent it simply by ensuring that we don't do that until
all tun descriptors ever attached to the device (even if they
have since be detached because they may still be sitting in poll)
have been closed.
This is done by using reference counting the attached tun file
descriptors. The refcount in tun->sk has been reappropriated
for this purpose since it was already being used for that, albeit
from the opposite angle.
Note that we no longer zero tfile->tun since tun_get will return
NULL anyway after the refcount on tfile hits zero. Instead it
represents whether this device has ever been attached to a device.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
We can in some situations drop packets in netif_rx()
loopback driver does not report these (unlikely) drops to its stats,
and incorrectly change packets/bytes counts.
After this patch applied, "ifconfig lo" can reports these drops as in :
# ifconfig lo
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:692562900 errors:3228 dropped:3228 overruns:0 frame:0
TX packets:692562900 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:2865674174 (2.6 GiB) TX bytes:2865674174 (2.6 GiB)
I initialy chose to reflect those errors only in tx_dropped/tx_errors, but David
convinced me that it was really RX errors, as loopback_xmit() really starts
a RX process. (calling eth_type_trans() for example, that itself pulls the ethernet header)
These errors are accounted in rx_dropped/rx_errors.
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
EEH attempts to recover up 6 times.
The last attempt leaves all the ports and adapter down.hen
The driver is then unloaded, bringing the adapter down again
unconditionally. The unload will hang.
Check if the adapter is already down before trying to bring it down again.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The fatal error task can be scheduled while processing an offload packet
in NAPI context when the connection handle is bogus. this can race
with the ports being brought down and the cxgb3 workqueue being flushed.
Stop napi processing before flushing the work queue.
The ULP drivers (iSCSI, iWARP) might also schedule a task on keventd_wk
while releasing a connection handle (cxgb3_offload.c::cxgb3_queue_tid_release()).
The driver however does not flush any work on keventd_wq while being unloaded.
This patch also fixes this.
Also call cancel_delayed_work_sync in place of the the deprecated
cancel_rearming_delayed_workqueue.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the existing periodic task to handle link faults.
The link fault interrupt handler is also called in work queue context,
which is wrong and might cause potential deadlocks.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As reported by Andrew Lutomirski <amluto@gmail.com>
All the intel wired ethernet drivers were calling netif_carrier_off
and netif_stop_queue (or variants) before calling register_netdevice
This is incorrect behavior as was pointed out by davem, and causes
ifconfig and friends to report a strange state before first link
after the driver was loaded.
This apparently confused *some* versions of networkmanager.
Andy tested this for e1000e and confirmed it was working for him.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Reported-by: Andrew Lutomirski <amluto@gmail.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As reported by Andrew Lutomirski <amluto@gmail.com>
All the intel wired ethernet drivers were calling netif_carrier_off
and netif_stop_queue (or variants) before calling register_netdevice
This is incorrect behavior as was pointed out by davem, and causes
ifconfig and friends to report a strange state before first link
after the driver was loaded, since without a netif_carrier_off, the stack
assumes carrier_on, but before register_netdev, netlink messages are not
sent out telling link state.
This apparently confused *some* versions of networkmanager.
Andy tested this for e1000e and confirmed it was working for him.
see thread: http://marc.info/?l=linux-netdev&m=123946479705636&w=2
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andy Lutomirski <amluto@gmail.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As reported by Andrew Lutomirski <amluto@gmail.com>
All the intel wired ethernet drivers were calling netif_carrier_off
and netif_stop_queue (or variants) before calling register_netdevice
This is incorrect behavior as was pointed out by davem, and causes
ifconfig and friends to report a strange state before first link
after the driver was loaded, since without a netif_carrier_off, the stack
assumes carrier_on, but before register_netdev, netlink messages are not
sent out telling link state.
This apparently confused *some* versions of networkmanager.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Reported-by: Andrew Lutomirski <amluto@gmail.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As reported by Andrew Lutomirski <amluto@gmail.com>
All the intel wired ethernet drivers were calling netif_carrier_off
and netif_stop_queue (or variants) before calling register_netdevice
This is incorrect behavior as was pointed out by davem, and causes
ifconfig and friends to report a strange state before first link
after the driver was loaded, since without a netif_carrier_off, the stack
assumes carrier_on, but before register_netdev, netlink messages are not
sent out telling link state.
This apparently confused *some* versions of networkmanager.
in addition this driver appeared to need a netif_start_queue at
the end of open.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Reported-by: Andrew Lutomirski <amluto@gmail.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As reported by Andrew Lutomirski <amluto@gmail.com>
All the intel wired ethernet drivers were calling netif_carrier_off
and netif_stop_queue (or variants) before calling register_netdevice
This is incorrect behavior as was pointed out by davem, and causes
ifconfig and friends to report a strange state before first link
after the driver was loaded, since without a netif_carrier_off, the stack
assumes carrier_on, but before register_netdev, netlink messages are not
sent out telling link state.
This apparently confused *some* versions of networkmanager.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Reported-by: Andrew Lutomirski <amluto@gmail.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Alexander Beregalov <a.beregalov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Check whether the underlying device provides a set of ethtool ops before
checking for individual handlers to avoid NULL pointer dereferences.
Reported-by: Art van Breemen <ard@telegraafnet.nl>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
A compilation error snuck into
2d90b0aa3b
due to an over-zealous indent script removing spaces around array
initialization ellipsis. The attached patch fixes the myri10ge
compilation in net-next.
Signed-off-by: Andrew Gallatin <gallatin@myri.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
EPERM means that disconnect() is runnung. It should be treated like
ENODEV
Signed-off-by: Oliver Neukum <oliver@neukum.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Suppose that we receive lots of frames, start processing them, but
exhaust our budget so that we return before we had a chance to look
at all of them.
Then, when the network layer calls us again, we will only continue
processing the buffers if the REC bit was set in the mean time, which it
might not be if there was a brief pause in the flow of packets. If this
happens, we'll simply display a warning and call netif_rx_complete()
with potentially lots of unprocessed packets in the RX ring...
Fix this by scanning the ring no matter what flags are set in the
interrupt status register.
Signed-off-by: Erik Waling <erik.waling@konftel.com>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When transfering large amounts of data we sometimes experienced that the
Retry Limit Exceeded (RLE) bit got set in TSR during transmission
attempts. When this happened the driver would stall in a state that
prevented any more data from being sent.
Signed-off-by: Erik Waling <erik.waling@konftel.com>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The thresholds for the DCB priority flow control are incorrect for 82599.
This fixes the thresholds to be correct.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The traffic classes in hardware are not symmetrical for Rx and Tx. Rx
is every 16 descriptor queues, Tx is not. It runs 32-32-16-16-8-8-8 when
running with 8 traffic classes, and runs 64-32-16 when running with 4
traffic classes. This patch fixes the mapping.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Cc: stable@kernel.org
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the e1000 transmit cleanup inner loop exited early, then
cleaned might not be true. This could cause tx hangs or other
badness. Use count to track the total number of descriptors
cleaned instead of basing a tx queue restart off of a temporary
working state variable.
This code now makes the flow the same for e1000/e1000e/igb/ixgbe
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the e1000e transmit cleanup inner loop exited early, then
cleaned might not be true. This could cause tx hangs or other
badness. Use count to track the total number of descriptors
cleaned instead of basing a tx queue restart off of a temporary
working state variable.
This code now makes the flow the same for e1000/e1000e/igb/ixgbe
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add MODULE_DEVICE_TABLE so that modinfo reports pci device id aliases.
Signed-off-by: Brice Goglin <brice@myri.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add myri10ge_fw_names to override the default firmware
on a per-board basis.
Signed-off-by: Brice Goglin <brice@myri.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Force a statistics update when our ethtool gstats routine
is called. Otherwise, ethtool will continue to read stale
stats until something forces an update by reading /proc/net/dev
This requires putting a lock around the stats update to guard
against 2 threads (one via ethtool, and one via procfs)
updating the stats at once.
Signed-off-by: Brice Goglin <brice@myri.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
GCC warns:
drivers/net/ixgbe/ixgbe_main.c: In function 'ixgbe_sfp_config_module_task':
drivers/net/ixgbe/ixgbe_main.c:3920: warning: suggest parantheses around
operand of '!' or change '&' to '&&' or '!' to '~'
Which I think is right. Bracket to remove ambiguity.
Signed-off-by: Tony Breeds <tony@bakeyournoodle.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
arm will pad even between u8's, so mark the structs/unions
packed. Fixes a build bug on arm due to BUILD_BUG_ON tests
in the code.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Reported-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Peter Holik
Matt Carlson
David S. Miller
Christian Lamparter
Joerg Albert
Joe Perches
Ivo van Doorn
Herbert Xu
Eric Dumazet
Marcin Slusarz
Divy Le Ray
Jesse Brandeburg
Alexander Beregalov
Patrick McHardy
Andrew Gallatin
Oliver Neukum
Erik Waling
Erik Waling
PJ Waskiewicz
Brice Goglin
Tony Breeds
Johannes Berg