Граф коммитов

23 Коммитов

Автор SHA1 Сообщение Дата
Benjamin Herrenschmidt 1e7342e778 Merge remote-tracking branch 'jwb/next' into next
Conflicts:
	arch/powerpc/platforms/40x/ppc40x_simple.c
2011-12-16 11:24:25 +11:00
Benjamin Herrenschmidt 11eab297f5 powerpc: Add support for OpenBlockS 600
So I've had one of these for a while and it looks like the vendor never
bothered submitting the support upstream.

This adds it using ppc40x_simple and provides a device-tree.

There are some changes to the boot wrapper because the way u-boot works
on this thing, it seems to expect a multipart image with the kernel,
initrd and dtb in it.

The USB support is missing as it needs the yet unmerged driver for
the DWC OTG part and the GPIOs may need further definition in the dts.

Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2011-12-08 14:22:52 +11:00
Tanmay Inamdar d5b9ee7b51 powerpc/40x: Add APM8018X SOC support
The AppliedMicro APM8018X embedded processor targets embedded applications that
require low power and a small footprint. It features a PowerPC 405 processor
core built in a 65nm low-power CMOS process with a five-stage pipeline executing
up to one instruction per cycle. The family has 128-kbytes of on-chip memory,
a 128-bit local bus and on-chip DDR2 SDRAM controller with 16-bit interface.

Signed-off-by: Tanmay Inamdar <tinamdar@apm.com>
Signed-off-by: Josh Boyer <jwboyer@gmail.com>
2011-11-30 10:02:15 -05:00
Linus Torvalds 1197ab2942 Merge branch 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (106 commits)
  powerpc/p3060qds: Add support for P3060QDS board
  powerpc/83xx: Add shutdown request support to MCU handling on MPC8349 MITX
  powerpc/85xx: Make kexec to interate over online cpus
  powerpc/fsl_booke: Fix comment in head_fsl_booke.S
  powerpc/85xx: issue 15 EOI after core reset for FSL CoreNet devices
  powerpc/8xxx: Fix interrupt handling in MPC8xxx GPIO driver
  powerpc/85xx: Add 'fsl,pq3-gpio' compatiable for GPIO driver
  powerpc/86xx: Correct Gianfar support for GE boards
  powerpc/cpm: Clear muram before it is in use.
  drivers/virt: add ioctl for 32-bit compat on 64-bit to fsl-hv-manager
  powerpc/fsl_msi: add support for "msi-address-64" property
  powerpc/85xx: Setup secondary cores PIR with hard SMP id
  powerpc/fsl-booke: Fix settlbcam for 64-bit
  powerpc/85xx: Adding DCSR node to dtsi device trees
  powerpc/85xx: clean up FPGA device tree nodes for Freecsale QorIQ boards
  powerpc/85xx: fix PHYS_64BIT selection for P1022DS
  powerpc/fsl-booke: Fix setup_initial_memory_limit to not blindly map
  powerpc: respect mem= setting for early memory limit setup
  powerpc: Update corenet64_smp_defconfig
  powerpc: Update mpc85xx/corenet 32-bit defconfigs
  ...

Fix up trivial conflicts in:
 - arch/powerpc/configs/40x/hcu4_defconfig
	removed stale file, edited elsewhere
 - arch/powerpc/include/asm/udbg.h, arch/powerpc/kernel/udbg.c:
	added opal and gelic drivers vs added ePAPR driver
 - drivers/tty/serial/8250.c
	moved UPIO_TSI to powerpc vs removed UPIO_DWAPB support
2011-11-06 17:12:03 -08:00
Tony Breeds 3b3bceef26 net: fix IBM EMAC driver after rename.
In commit 9aa3283595 (ehea/ibm*: Move the
IBM drivers) the IBM_NEW_EMAC* were renames to IBM_EMAC*

The conversion was incomplete so that even if the driver was added to
the .config it wasn't built, but there were no errors).  In this commit
we also update the various defconfigs that use EMAC to use the new
Kconfig symbol, and explicitly add the NET_VENDOR_IBM guard.

We do not explicitly select the Kconfig dependencies, as this would force
EMAC on.  Doing it in the defconfig allows more flexibility.

Tested on a canyondlands board.

Signed-off-by: Tony Breeds <tony@bakeyournoodle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2011-08-18 21:33:49 -07:00
Josh Boyer 9fcd768d0c powerpc/40x: Remove obsolete HCU4 board
The HCU4 board is unmaintained.  Remove it.

Signed-off-by: Niklaus Giger <niklaus.giger@member.fsf.org>
Signed-off-by: Josh Boyer <jwboyer@gmail.com>
2011-08-11 13:56:43 -04:00
David Rientjes 6a108a14fa kconfig: rename CONFIG_EMBEDDED to CONFIG_EXPERT
The meaning of CONFIG_EMBEDDED has long since been obsoleted; the option
is used to configure any non-standard kernel with a much larger scope than
only small devices.

This patch renames the option to CONFIG_EXPERT in init/Kconfig and fixes
references to the option throughout the kernel.  A new CONFIG_EMBEDDED
option is added that automatically selects CONFIG_EXPERT when enabled and
can be used in the future to isolate options that should only be
considered for embedded systems (RISC architectures, SLOB, etc).

Calling the option "EXPERT" more accurately represents its intention: only
expert users who understand the impact of the configuration changes they
are making should enable it.

Reviewed-by: Ingo Molnar <mingo@elte.hu>
Acked-by: David Woodhouse <david.woodhouse@intel.com>
Signed-off-by: David Rientjes <rientjes@google.com>
Cc: Greg KH <gregkh@suse.de>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Robin Holt <holt@sgi.com>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2011-01-20 17:02:05 -08:00
Victor Gallardo 05ed60874e powerpc/4xx: Add Kilauea suspend and idle support
- Add Clock Power Management (CPM) node to dts tree
- Add idle-doze entry in CPM node
- Add standby entry in CPM node
- Add PM and SUSPEND support by default in defconfig
- Add NO_HZ and CONFIG_HIGH_RES_TIMERS support by
  default in defconfig

Signed-off-by: Victor Gallardo <vgallardo@apm.com>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
2010-11-29 10:05:18 -05:00
Benjamin Herrenschmidt 61a3e1665f powerpc: Trim defconfigs
This trims all our defconfigs using make savedefconfig

Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2010-08-09 11:19:16 +10:00
Grant Likely 65cf840ff4 powerpc: Disable CONFIG_SYSFS_DEPRECATED
Acked-by: Grant Likely <grant.likely@secretlab.ca>

On 5 May 2010 21:33, "Anton Blanchard" <anton@samba.org> wrote:

CONFIG_SYSFS_DEPRECATED can cause issues with newer distros and should not
be required for any distro in the last 3 or 4 years, so disable it.

Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2010-06-15 15:02:33 +10:00
Josh Boyer 02ea22896a powerpc/40x: Update the PowerPC 40x board defconfigs
Update the 40x defconfigs for 2.6.33

Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
2010-01-04 10:59:32 -05:00
Stefan Roese 6b045a818f powerpc/40x: Update kilauea defconfig to support NAND, RTC and HWMON
This patch adds support for the following devices to the Kilauea
defconfig file:
- PPC4xx NAND controller (NDFC)
- I2C RTC (Dallas DS1338)
- I2C HWMON (Dallas DS1775)

Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2009-08-20 10:25:52 +10:00
Josh Boyer 336ff73542 powerpc/40x: Convert AMCC Kilauea/Halekala boards to ppc40x_simple
This cleans up the kilauea/halekala board ports to use the ppc40x_simple
platform support.

Tested-by: Stefan Roese <sr@denx.de>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
2009-06-04 09:02:21 -04:00
Josh Boyer 194ff1c387 powerpc/40x: Convert AMCC Makalu board to ppc40x_simple
This cleans up the makalu board port to use the ppc40x_simple platform
support.

Tested-by: Stefan Roese <sr@denx.de>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
2009-06-04 09:02:09 -04:00
Josh Boyer 27db1fea18 powerpc/4xx: Disable PCI_LEGACY
The single board defconfig files were missed during the cleanup
of CONFIG_PCI_LEGACY in the multi-board config files.  This
disables the option for the single board configs, as it isn't
used by anything for these boards.

Reported-by: Cheng Renquan <crquan@gmail.com>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
2009-06-03 16:23:15 -04:00
Grant Likely 6b8036a877 powerpc/4xx: Enable SERIAL_OF support by default for Virtex platforms
Virtex FPGA designs have two serial port logic cores to choose from; the
simple uartlite, and the full featured uart16550.  Both cores are in
common use so the defconfig should support both of them.  Currently
only console on uartlite is supported in the defconfig.  This patch adds
console support for the 16550 core.

The Virtex reference designs do not work without this patch.

Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2009-02-28 21:30:38 -07:00
Josh Boyer e801c72d61 powerpc/40x: Update PowerPC 40x defconfigs
Update the 40x defconfigs for 2.6.29-rc2

Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
2009-01-20 13:01:54 -05:00
Grant Likely c8d698849e powerpc/virtex: Update defconfigs
Update defconfigs for running on Xilinx Virtex platforms

Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2008-11-14 11:10:55 -07:00
Josh Boyer c4cd9ec48a powerpc/40x: Update 40x defconfigs
Update the PowerPC 40x defconfigs for 2.6.28

Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
2008-10-30 18:16:14 -04:00
Niklaus Giger 9fa126da4a powerpc/40x: Add support for Netstal HCU4 board
Adds support for a HCU4 PPC405GPr based board from Netstal Maschinen AG.

Signed-off-by: Niklaus Giger <niklaus.giger@member.fsf.org>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
2008-10-17 13:28:05 -04:00
Josh Boyer 4cbfc467cc powerpc/40x: Add PowerPC 405EZ Acadia defconfig
Add simple defconfig for the AMCC PowerPC 405EZ Acadia evaluation board

Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
2008-10-17 10:31:19 -04:00
Josh Boyer 9ea7d5ad84 powerpc/4xx: Update defconfig files for 2.6.27-rc1
Update the defconfig files for 4xx boards.  This also makes the mutli-board
defconfigs a bit more useful by enabling some of the more common modules.

Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
2008-08-06 07:55:37 -04:00
Josh Boyer 975386ee0e [POWERPC] 4xx: Reorganize 4xx defconfigs
Board specific defconfigs are useful, however with the ability to do
multi-board defconfigs they aren't needed in the top level configs directory.

Move the 4xx board specific defconfigs to individual directories under
arch/powerpc/configs.

Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
2008-04-15 08:12:57 -05:00