[ Upstream commit 4cf2ddf16e ]
Starting with commit d92ed2c9d3 ("thermal: imx: Use driver's local
data to decide whether to run a measurement") this driver stared using
irq_enabled flag to make decision to power on/off the thermal
core. This triggered a regression, where after reaching critical
temperature, alarm IRQ handler set irq_enabled to false, disabled
thermal core and was not able read temperature and disable cooling
sequence.
In case the cooling device is "CPU/GPU freq", the system will run with
reduce performance until next reboot.
To solve this issue, we need to move all parts implementing hand made
runtime power management and let it handle actual runtime PM framework.
Fixes: d92ed2c9d3 ("thermal: imx: Use driver's local data to decide whether to run a measurement")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Tested-by: Petr Beneš <petr.benes@ysoft.com>
Link: https://lore.kernel.org/r/20211117103426.81813-1-o.rempel@pengutronix.de
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4047b9db1a ]
dwmac-qcom-ethqos currently exposes a mechanism to dump rgmii registers
after the 'stmmac_dvr_probe()' returns. However with commit
5ec5582343 ("net: stmmac: add clocks management for gmac driver"),
we now let 'pm_runtime_put()' disable the clocks before returning from
'stmmac_dvr_probe()'.
This causes a crash when 'rgmii_dump()' register dumps are enabled,
as the clocks are already off.
Since other dwmac drivers (possible future users as well) might
require a similar register dump feature, introduce a platform level
callback to allow the same.
This fixes the crash noticed while enabling rgmii_dump() dumps in
dwmac-qcom-ethqos driver as well. It also allows future changes
to keep a invoking the register dump callback from the correct
place inside 'stmmac_dvr_probe()'.
Fixes: 5ec5582343 ("net: stmmac: add clocks management for gmac driver")
Cc: Joakim Zhang <qiangqing.zhang@nxp.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8cc7a1b2ac ]
A successful 'of_platform_populate()' call should be balanced by a
corresponding 'of_platform_depopulate()' call in the error handling path
of the probe, as already done in the remove function.
A successful 'venus_firmware_init()' call should be balanced by a
corresponding 'venus_firmware_deinit()' call in the error handling path
of the probe, as already done in the remove function.
Update the error handling path accordingly.
Fixes: f9799fcce4 ("media: venus: firmware: register separate platform_device for firmware loader")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e4debea9be ]
The normal path of the function makes the assumption that
'pm_ops->core_power' may be NULL.
We should make the same assumption in the error handling path or a NULL
pointer dereference may occur.
Add the missing test before calling 'pm_ops->core_power'
Fixes: 9e8efdb578 ("media: venus: core: vote for video-mem path")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b1f9bb8020 ]
In exististing implimentation, in min_loaded_core() for low_power
vpp frequency value is considering as vpp_freq instead of low_power_freq.
Fixed this by correcting vpp frequency calculation for encoder.
Fixes: 3cfe5815ce (media: venus: Enable low power setting for encoder)
Signed-off-by: Mansur Alisha Shaik <mansur@codeaurora.org>
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1a59cd88f5 ]
Stop the CODA960 JPEG encoder from overflowing capture buffers.
The bitstream buffer overflow interrupt doesn't seem to be connected,
so this has to be handled via timeout instead.
Reported-by: Martin Weber <martin.weber@br-automation.com>
Fixes: 96f6f62c46 ("media: coda: jpeg: add CODA960 JPEG encoder support")
Tested-by: Martin Weber <martin.weber@br-automation.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 230d683ae0 ]
The JPEG encoder found in the Hantro H1 encoder block only produces a
raw entropy-encoded scan. The driver is responsible for building a JPEG
compliant bitstream and placing the entropy-encoded scan in it. Right
now the driver uses a bounce buffer for the hardware to output the raw
scan to.
In commit e765dba11e ("hantro: Move hantro_enc_buf_finish to JPEG
codec_ops.done"), the code that copies the raw scan from the bounce
buffer to the capture buffer was moved, but was only hooked up for the
Hantro H1 (then RK3288) variant. The RK3399 variant was broken,
producing a JPEG bitstream without the scan, and the capture buffer's
.bytesused field unset.
Fix this by duplicating the code that is executed when the JPEG encoder
finishes encoding a frame. As the encoded length is read back from
hardware, and the variants having different register layouts, the
code is duplicated rather than shared.
Fixes: e765dba11e ("hantro: Move hantro_enc_buf_finish to JPEG codec_ops.done")
Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>
Tested-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ed2f97ad4b ]
After devm_request_threaded_irq() is called there is a chance that an
interrupt may occur before the spinlock is initialized, which will trigger
a kernel oops.
To prevent that, move the initialization of the spinlock prior to
requesting the interrupts.
Fixes: 51abcf7fdb ("media: imx-pxp: add i.MX Pixel Pipeline driver")
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cee44d4fba ]
hsfreqrange should be chosen based on the calculated mbps which
is closer to the default bit rate and within the range as per
table[1]. But current calculation always selects first value which
is greater than or equal to the calculated mbps which may lead
to chosing a wrong range in some cases.
For example for 360 mbps for H3/M3N
Existing logic selects
Calculated value 360Mbps : Default 400Mbps Range [368.125 -433.125 mbps]
This hsfreqrange is out of range.
The logic is changed to get the default value which is closest to the
calculated value [1]
Calculated value 360Mbps : Default 350Mbps Range [320.625 -380.625 mpbs]
[1] specs r19uh0105ej0200-r-car-3rd-generation.pdf [Table 25.9]
Please note that According to Renesas in Table 25.9 the range for
220 default value is corrected as below
|Range (Mbps) | Default Bit rate (Mbps) |
-----------------------------------------------
| 197.125-244.125 | 220 |
-----------------------------------------------
Fixes: 769afd212b ("media: rcar-csi2: add Renesas R-Car MIPI CSI-2 receiver driver")
Signed-off-by: Suresh Udipi <sudipi@jp.adit-jv.com>
Signed-off-by: Kazuyoshi Akiyama <akiyama@nds-osk.co.jp>
Signed-off-by: Michael Rodin <mrodin@de.adit-jv.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6e1c9bc9ae ]
ov8865_state_init() calls ov8865_state_mipi_configure() which uses
__v4l2_ctrl_s_ctrl[_int64](). This means that sensor->mutex (which
is also sensor->ctrls.handler.lock) must be locked before calling
ov8865_state_init().
Note ov8865_state_mipi_configure() is also used in other places where
the lock is already held so it cannot be changed itself.
This fixes the following lockdep kernel WARN:
[ 13.233421] WARNING: CPU: 0 PID: 8 at drivers/media/v4l2-core/v4l2-ctrls-api.c:833 __v4l2_ctrl_s_ctrl+0x4d/0x60 [videodev]
...
[ 13.234063] Call Trace:
[ 13.234074] ov8865_state_configure+0x98b/0xc00 [ov8865]
[ 13.234095] ov8865_probe+0x4b1/0x54c [ov8865]
[ 13.234117] i2c_device_probe+0x13c/0x2d0
Fixes: 11c0d8fdcc ("media: i2c: Add support for the OV8865 image sensor")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d2484fbf78 ]
The kerneldoc for pm_runtime_set_suspended() says:
"It is not valid to call this function for devices with runtime PM
enabled"
To satisfy that requirement, re-order the calls so that
pm_runtime_enable() is the last one.
Fixes: 11c0d8fdcc ("media: i2c: Add support for the OV8865 image sensor")
Signed-off-by: Daniel Scally <djrscally@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 43174f0d45 ]
When compiling libbpf with gcc 4.8.5, we see:
CC staticobjs/btf_dump.o
btf_dump.c: In function ‘btf_dump_dump_type_data.isra.24’:
btf_dump.c:2296:5: error: ‘err’ may be used uninitialized in this function [-Werror=maybe-uninitialized]
if (err < 0)
^
cc1: all warnings being treated as errors
make: *** [staticobjs/btf_dump.o] Error 1
While gcc 4.8.5 is too old to build the upstream kernel, it's possible it
could be used to build standalone libbpf which suffers from the same problem.
Silence the error by initializing 'err' to 0. The warning/error seems to be
a false positive since err is set early in the function. Regardless we
shouldn't prevent libbpf from building for this.
Fixes: 920d16af9b ("libbpf: BTF dumper support for typed data")
Signed-off-by: Alan Maguire <alan.maguire@oracle.com>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/bpf/1638180040-8037-1-git-send-email-alan.maguire@oracle.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c65e6fd460 ]
Commit 7cc4ffc555 ("block, bfq: put reqs of waker and woken in
dispatch list") added a condition to bfq_insert_request() which added
waker's requests directly to dispatch list. The rationale was that
completing waker's IO is needed to get more IO for the current queue.
Although this rationale is valid, there is a hole in it. The waker does
not necessarily serve the IO only for the current queue and maybe it's
current IO is not needed for current queue to make progress. Furthermore
injecting IO like this completely bypasses any service accounting within
bfq and thus we do not properly track how much service is waker's queue
getting or that the waker is actually doing any IO. Depending on the
conditions this can result in the waker getting too much or too few
service.
Consider for example the following job file:
[global]
directory=/mnt/repro/
rw=write
size=8g
time_based
runtime=30
ramp_time=10
blocksize=1m
direct=0
ioengine=sync
[slowwriter]
numjobs=1
prioclass=2
prio=7
fsync=200
[fastwriter]
numjobs=1
prioclass=2
prio=0
fsync=200
Despite processes have very different IO priorities, they get the same
about of service. The reason is that bfq identifies these processes as
having waker-wakee relationship and once that happens, IO from
fastwriter gets injected during slowwriter's time slice. As a result bfq
is not aware that fastwriter has any IO to do and constantly schedules
only slowwriter's queue. Thus fastwriter is forced to compete with
slowwriter's IO all the time instead of getting its share of time based
on IO priority.
Drop the special injection condition from bfq_insert_request(). As a
result, requests will be tracked and queued in a normal way and on next
dispatch bfq_select_queue() can decide whether the waker's inserted
requests should be injected during the current queue's timeslice or not.
Fixes: 7cc4ffc555 ("block, bfq: put reqs of waker and woken in dispatch list")
Acked-by: Paolo Valente <paolo.valente@linaro.org>
Signed-off-by: Jan Kara <jack@suse.cz>
Link: https://lore.kernel.org/r/20211125133645.27483-8-jack@suse.cz
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5d051cf94f ]
Flexcom IP embeds 3 other IPs: usart, i2c, spi and selects the operation
mode (usart, i2c, spi) via mode register (FLEX_MR). On i2c bus there might
be connected critical devices (like PMIC) which on suspend/resume should
be suspended/resumed at the end/beginning. i2c uses
.suspend_noirq/.resume_noirq for this kind of purposes. Align flexcom
to use .resume_noirq as it should be resumed before the embedded IPs.
Otherwise the embedded devices might behave badly.
Fixes: 7fdec11015 ("atmel_flexcom: Support resuming after a chip reset")
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Tested-by: Codrin Ciubotariu <codrin.ciubotariu@microchip.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20211028135138.3481166-3-claudiu.beznea@microchip.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8c0fad75dc ]
Remove compilation flag and use __maybe_unused and pm_ptr instead.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20211028135138.3481166-2-claudiu.beznea@microchip.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4f4b9b5895 ]
The driver wrongly assummed that tx_submit() will start the transfer,
which is not the case, now that the at_xdmac driver is fixed. tx_submit
is supposed to push the current transaction descriptor to a pending queue,
waiting for issue_pending to be called. issue_pending must start the
transfer, not tx_submit.
Fixes: 34df42f59a ("serial: at91: add rx dma support")
Fixes: 08f738be88 ("serial: at91: add tx dma support")
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20211125090028.786832-4-tudor.ambarus@microchip.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1e67bd2b8c ]
The tx_submit() method of struct dma_async_tx_descriptor is entitled
to do sanity checks and return errors if encountered. It's not the
case for the DMA controller drivers that this client is using
(at_h/xdmac), because they currently don't do sanity checks and always
return a positive cookie at tx_submit() method. In case the controller
drivers will implement sanity checks and return errors, print a message
so that the client will be informed that something went wrong at
tx_submit() level.
Fixes: 08f738be88 ("serial: at91: add tx dma support")
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Acked-by: Richard Genoud <richard.genoud@gmail.com>
Link: https://lore.kernel.org/r/20211125090028.786832-3-tudor.ambarus@microchip.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b689f091aa ]
CE interrupt configuration uses host ce parameters to assign/free
interrupts. Use host ce parameters to enable/disable interrupts.
This patch fixes below BUG,
BUG: KASAN: global-out-of-bounds in 0xffffffbffdfb035c at addr
ffffffbffde6eeac
Read of size 4 by task kworker/u8:2/132
Address belongs to variable ath11k_core_qmi_firmware_ready+0x1b0/0x5bc [ath11k]
OOB is due to ath11k_ahb_ce_irqs_enable() iterates ce_count(which is 12)
times and accessing 12th element in target_ce_config
(which has only 11 elements) from ath11k_ahb_ce_irq_enable().
With this change host ce configs are used to enable/disable interrupts.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.5.0.1-00471-QCAHKSWPL_SILICONZ-1
Fixes: 967c1d1131 ("ath11k: move target ce configs to hw_params")
Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1637249558-12793-1-git-send-email-akolli@codeaurora.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5002200b4f ]
If the remote function did not ACK the reception of a message, the
function __adf_iov_putmsg() could detect it as a collision.
This was due to the fact that the collision and the timeout checks after
the ACK loop were in the wrong order. The timeout must be checked at the
end of the loop, so fix by swapping the order of the two checks.
Fixes: 9b768e8a39 ("crypto: qat - detect PFVF collision after ACK")
Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Co-developed-by: Marco Chiappero <marco.chiappero@intel.com>
Signed-off-by: Marco Chiappero <marco.chiappero@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6e680f94bc ]
The functions adf_iov_putmsg() and __adf_iov_putmsg() are shared by both
PF and VF. Any logging or documentation should not refer to any specific
direction.
Make comments and log messages direction agnostic by replacing PF2VF
with PFVF. Also fix the wording for some related comments.
Signed-off-by: Marco Chiappero <marco.chiappero@intel.com>
Co-developed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e17f49bb24 ]
The initial version of the PFVF protocol included an initial "carrier
sensing" to get ownership of the channel.
Collisions can happen anyway, the extra wait and test does not prevent
collisions, it instead slows the communication down, so remove it.
Signed-off-by: Marco Chiappero <marco.chiappero@intel.com>
Reviewed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 401891a9de ]
Perform a memory copy before we do the sanity checks of btf_ext_hdr.
This prevents misaligned memory access if raw btf_ext data is not 4-byte
aligned ([0]).
While at it, also add missing const qualifier.
[0] Closes: https://github.com/libbpf/libbpf/issues/391
Fixes: 2993e0515b ("tools/bpf: add support to read .BTF.ext sections")
Reported-by: Evgeny Vereshchagin <evvers@ya.ru>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20211124002325.1737739-3-andrii@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b046049e59 ]
Since the compatible string defined from ilitek,ili9341.yaml is
"st,sf-tc240t-9370-t", "ilitek,ili9341"
so, append "ilitek,ili9341" to avoid the below dtbs_check warning.
arch/arm/boot/dts/stm32f429-disco.dt.yaml: display@1: compatible:
['st,sf-tc240t-9370-t'] is too short
Fixes: a726e2f000 ("ARM: dts: stm32: enable ltdc binding with ili9341, gyro l3gd20 on stm32429-disco board")
Signed-off-by: Dillon Min <dillon.minfei@gmail.com>
Reported-by: kernel test robot <lkp@intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e0e27c3d4e ]
Re-enabling an interrupt from its own interrupt handler may cause
an interrupt storm, if there is a pending interrupt and because its
handling is disabled due to already done entrance into the handler
above in the stack.
Also, apparently it is improper to lock a mutex in an interrupt contex.
Fixes: 275157b367 ("cpufreq: qcom-cpufreq-hw: Add dcvs interrupt support")
Signed-off-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 93d9e6f93e ]
The thermal pressure signal gives information to the scheduler about
reduced CPU capacity due to thermal. It is based on a value stored in
a per-cpu 'thermal_pressure' variable. The online CPUs will get the
new value there, while the offline won't. Unfortunately, when the CPU
is back online, the value read from per-cpu variable might be wrong
(stale data). This might affect the scheduler decisions, since it
sees the CPU capacity differently than what is actually available.
Fix it by making sure that all online+offline CPUs would get the
proper value in their per-cpu variable when there is throttling
or throttling is removed.
Fixes: 275157b367 ("cpufreq: qcom-cpufreq-hw: Add dcvs interrupt support")
Reviewed-by: Thara Gopinath <thara.gopinath@linaro.org>
Signed-off-by: Lukasz Luba <lukasz.luba@arm.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit baaf965f94 ]
The following KASAN BUG is observed when testing the rpc-if driver on
rcar-gen3:
root@rcar-gen3:~# modprobe -r rpc-if
[ 101.930146] ==================================================================
[ 101.937408] BUG: KASAN: slab-out-of-bounds in __lock_acquire+0x518/0x25d0
[ 101.944240] Read of size 8 at addr ffff0004c5be2750 by task modprobe/664
[ 101.950959]
[ 101.952466] CPU: 2 PID: 664 Comm: modprobe Not tainted 5.14.0-rc1-00342-g1a1464d7aa31 #1
[ 101.960578] Hardware name: Renesas H3ULCB board based on r8a77951 (DT)
[ 101.967120] Call trace:
[ 101.969580] dump_backtrace+0x0/0x2c0
[ 101.973275] show_stack+0x1c/0x30
[ 101.976616] dump_stack_lvl+0x9c/0xd8
[ 101.980301] print_address_description.constprop.0+0x74/0x2b8
[ 101.986071] kasan_report+0x1f4/0x26c
[ 101.989757] __asan_load8+0x98/0xd4
[ 101.993266] __lock_acquire+0x518/0x25d0
[ 101.997215] lock_acquire.part.0+0x18c/0x360
[ 102.001506] lock_acquire+0x74/0x90
[ 102.005013] _raw_spin_lock_irq+0x98/0x130
[ 102.009131] __pm_runtime_disable+0x30/0x210
[ 102.013427] rpcif_hb_remove+0x5c/0x70 [rpc_if]
[ 102.018001] platform_remove+0x40/0x80
[ 102.021771] __device_release_driver+0x234/0x350
[ 102.026412] driver_detach+0x158/0x20c
[ 102.030179] bus_remove_driver+0xa0/0x140
[ 102.034212] driver_unregister+0x48/0x80
[ 102.038153] platform_driver_unregister+0x18/0x24
[ 102.042879] rpcif_platform_driver_exit+0x1c/0x34 [rpc_if]
[ 102.048400] __arm64_sys_delete_module+0x210/0x310
[ 102.053212] invoke_syscall+0x60/0x190
[ 102.056986] el0_svc_common+0x12c/0x144
[ 102.060844] do_el0_svc+0x88/0xac
[ 102.064181] el0_svc+0x24/0x3c
[ 102.067257] el0t_64_sync_handler+0x1a8/0x1b0
[ 102.071634] el0t_64_sync+0x198/0x19c
[ 102.075315]
[ 102.076815] Allocated by task 628:
[ 102.080781]
[ 102.082280] Last potentially related work creation:
[ 102.087524]
[ 102.089022] The buggy address belongs to the object at ffff0004c5be2000
[ 102.089022] which belongs to the cache kmalloc-2k of size 2048
[ 102.101555] The buggy address is located 1872 bytes inside of
[ 102.101555] 2048-byte region [ffff0004c5be2000, ffff0004c5be2800)
[ 102.113486] The buggy address belongs to the page:
[ 102.118409]
[ 102.119908] Memory state around the buggy address:
[ 102.124711] ffff0004c5be2600: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
[ 102.131947] ffff0004c5be2680: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
[ 102.139181] >ffff0004c5be2700: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
[ 102.146412] ^
[ 102.152257] ffff0004c5be2780: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
[ 102.159491] ffff0004c5be2800: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
[ 102.166723] ==================================================================
The above bug is caused by use of the wrong pointer in the
rpcif_disable_rpm() call. Fix the bug by using the correct pointer.
Fixes: 5de15b610f ("mtd: hyperbus: add Renesas RPC-IF driver")
Signed-off-by: George G. Davis <davis.george@siemens.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20210716204935.25859-1-george_davis@mentor.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e9c195aaee ]
Pointer alg points to sub field of tmpl, it
is dereferenced after tmpl is freed. Fix
this by accessing alg before free tmpl.
Fixes: ec8f5d8f ("crypto: qce - Qualcomm crypto engine driver")
Signed-off-by: Chengfeng Ye <cyeaa@connect.ust.hk>
Acked-by: Thara Gopinath <thara.gopinath@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b4cb4d3163 ]
Pointer base points to sub field of tmpl, it
is dereferenced after tmpl is freed. Fix
this by accessing base before free tmpl.
Fixes: ec8f5d8f ("crypto: qce - Qualcomm crypto engine driver")
Signed-off-by: Chengfeng Ye <cyeaa@connect.ust.hk>
Acked-by: Thara Gopinath <thara.gopinath@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4a9dbd0219 ]
Pointer alg points to sub field of tmpl, it
is dereferenced after tmpl is freed. Fix
this by accessing alg before free tmpl.
Fixes: 9363efb4 ("crypto: qce - Add support for AEAD algorithms")
Signed-off-by: Chengfeng Ye <cyeaa@connect.ust.hk>
Acked-by: Thara Gopinath <thara.gopinath@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6d48de6559 ]
In case there were more requests from different tfms in the crypto
queue, only the context of the last initialized tfm was considered.
Fixes: ec2088b66f ("crypto: atmel-aes - Allocate aes dev at tfm init time")
Reported-by: Wolfgang Ocker <weo@reccoware.de>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ab599eb118 ]
I got a use-after-free report:
dvbdev: dvb_register_device: failed to create device dvb1.dvr0 (-12)
...
==================================================================
BUG: KASAN: use-after-free in dvb_dmxdev_release+0xce/0x2f0
...
Call Trace:
dump_stack_lvl+0x6c/0x8b
print_address_description.constprop.0+0x48/0x70
kasan_report.cold+0x82/0xdb
__asan_load4+0x6b/0x90
dvb_dmxdev_release+0xce/0x2f0
...
Allocated by task 7666:
kasan_save_stack+0x23/0x50
__kasan_kmalloc+0x83/0xa0
kmem_cache_alloc_trace+0x22e/0x470
dvb_register_device+0x12f/0x980
dvb_dmxdev_init+0x1f3/0x230
...
Freed by task 7666:
kasan_save_stack+0x23/0x50
kasan_set_track+0x20/0x30
kasan_set_free_info+0x24/0x40
__kasan_slab_free+0xf2/0x130
kfree+0xd1/0x5c0
dvb_register_device.cold+0x1ac/0x1fa
dvb_dmxdev_init+0x1f3/0x230
...
When dvb_register_device() in dvb_dmxdev_init() fails, dvb_dmxdev_init()
does not return a failure, and the memory pointed to by dvbdev or
dvr_dvbdev is invalid at this point. If they are used subsequently, it
will result in UFA or null-ptr-deref.
If dvb_register_device() in dvb_dmxdev_init() fails, fix the bug by making
dvb_dmxdev_init() return an error as well.
Link: https://lore.kernel.org/linux-media/20211015085741.1203283-1-wanghai38@huawei.com
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wang Hai <wanghai38@huawei.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e1a9faddff ]
The CAT875 sub board from Silicon Linux uses a Realtek PHY.
The phy driver commit bbc4d71d63 ("net: phy: realtek: fix
rtl8211e rx/tx delay config") introduced NFS mount failures. Now it
needs both rx/tx delays for the NFS mount to work.
This patch fixes the NFS mount failure issue by adding "rgmii-id" mode
to the avb device node.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Fixes: bbc4d71d63 ("net: phy: realtek: fix rtl8211e rx/tx delay config")
Link: https://lore.kernel.org/r/20211115142830.12651-1-biju.das.jz@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cebbb5c46d ]
The devm_gen_pool_create() function never returns NULL, it returns
error pointers.
Fixes: 4cc9b56545 ("drm/vboxvideo: Use devm_gen_pool_create")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211118111233.GA1147@kili
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 646596485e ]
As it turns out, apparently some machines will actually leave additional
backlight functionality like dynamic backlight control on before the OS
loads. Currently we don't take care to disable unsupported features when
writing back the backlight mode, which can lead to some rather strange
looking behavior when adjusting the backlight.
So, let's fix this by just not reading back the current backlight mode on
initial enable. I don't think there should really be any downsides to this,
and this will ensure we don't leave any unsupported functionality enabled.
This should fix at least one (but not all) of the issues seen with DPCD
backlight support on fi-bdw-samus
v5:
* Just avoid reading back DPCD register - Doug Anderson
Signed-off-by: Lyude Paul <lyude@redhat.com>
Fixes: 867cf9cd73 ("drm/dp: Extract i915's eDP backlight code into DRM helpers")
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20211105183342.130810-4-lyude@redhat.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1b9beda83e ]
This patch will surround the AF_INET6 case in sk_error_report() of dlm
with a #if IS_ENABLED(CONFIG_IPV6). The field sk->sk_v6_daddr is not
defined when CONFIG_IPV6 is disabled. If CONFIG_IPV6 is disabled, the
socket creation with AF_INET6 should already fail because a runtime
check if AF_INET6 is registered. However if there is the possibility
that AF_INET6 is set as sk_family the sk_error_report() callback will
print then an invalid family type error.
Reported-by: kernel test robot <lkp@intel.com>
Fixes: 4c3d90570b ("fs: dlm: don't call kernel_getpeername() in error_report()")
Signed-off-by: Alexander Aring <aahringo@redhat.com>
Signed-off-by: David Teigland <teigland@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f18397ab3a ]
Prior to this patch was teedev_close_context() calling tee_device_put()
before teedev_ctx_put() leading to teedev_ctx_release() accessing
ctx->teedev just after the reference counter was decreased on the
teedev. Fix this by calling teedev_ctx_put() before tee_device_put().
Fixes: 217e0250cc ("tee: use reference counting for tee_context")
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Jens Wiklander <jens.wiklander@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 64bc3aa02a ]
The ath11k driver is caching the information about RSN/WPA IE in the
configured beacon template. The cached information is used during
associations to figure out whether 4-way PKT/2-way GTK peer flags need to
be set or not.
But the code never cleared the state when no such IE was found. This can
for example happen when moving from an WPA/RSN to an open setup. The
(seemingly connected) peer was then not able to communicate over the
link because the firmware assumed a different (encryption enabled) state
for the peer.
Tested-on: IPQ6018 hw1.0 AHB WLAN.HK.2.5.0.1-01100-QCAHKSWPL_SILICONZ-1
Fixes: 01e34233c6 ("ath11k: fix wmi peer flags in peer assoc command")
Cc: Venkateswara Naralasetty <vnaralas@codeaurora.org>
Reported-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Karthikeyan Kathirvel <kathirve@codeaurora.org>
[sven@narfation.org: split into separate patches, clean up commit message]
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211115100441.33771-2-sven@narfation.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 436a4e8865 ]
DISABLE_KEY sets the key_len to 0, firmware will not delete the keys if
key_len is 0. Changing from security mode to open mode will cause mcast
to be still encrypted without vdev restart.
Set the proper key_len for DISABLE_KEY cmd to clear the keys in
firmware.
Tested-on: IPQ6018 hw1.0 AHB WLAN.HK.2.5.0.1-01100-QCAHKSWPL_SILICONZ-1
Fixes: d5c65159f2 ("ath11k: driver for Qualcomm IEEE 802.11ax devices")
Reported-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Karthikeyan Kathirvel <kathirve@codeaurora.org>
[sven@narfation.org: split into separate patches, clean up commit message]
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211115100441.33771-1-sven@narfation.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 086c921a35 ]
Some ETSI countries have a small overlap in the wireless-regdb with an ETSI
channel (5590-5650). A good example is Australia:
country AU: DFS-ETSI
(2400 - 2483.5 @ 40), (36)
(5150 - 5250 @ 80), (23), NO-OUTDOOR, AUTO-BW
(5250 - 5350 @ 80), (20), NO-OUTDOOR, AUTO-BW, DFS
(5470 - 5600 @ 80), (27), DFS
(5650 - 5730 @ 80), (27), DFS
(5730 - 5850 @ 80), (36)
(57000 - 66000 @ 2160), (43), NO-OUTDOOR
If the firmware (or the BDF) is shipped with these rules then there is only
a 10 MHz overlap with the weather radar:
* below: 5470 - 5590
* weather radar: 5590 - 5600
* above: (none for the rule "5470 - 5600 @ 80")
There are several wrong assumption in the ath11k code:
* there is always a valid range below the weather radar
(actually: there could be no range below the weather radar range OR range
could be smaller than 20 MHz)
* intersected range in the weather radar range is valid
(actually: the range could be smaller than 20 MHz)
* range above weather radar is either empty or valid
(actually: the range could be smaller than 20 MHz)
These wrong assumption will lead in this example to a rule
(5590 - 5600 @ 20), (N/A, 27), (600000 ms), DFS, AUTO-BW
which is invalid according to is_valid_reg_rule() because the freq_diff is
only 10 MHz but the max_bandwidth is set to 20 MHz. Which results in a
rejection like:
WARNING: at backports-20210222_001-4.4.60-b157d2276/net/wireless/reg.c:3984
[...]
Call trace:
[<ffffffbffc3d2e50>] reg_get_max_bandwidth+0x300/0x3a8 [cfg80211]
[<ffffffbffc3d3d0c>] regulatory_set_wiphy_regd_sync+0x3c/0x98 [cfg80211]
[<ffffffbffc651598>] ath11k_regd_update+0x1a8/0x210 [ath11k]
[<ffffffbffc652108>] ath11k_regd_update_work+0x18/0x20 [ath11k]
[<ffffffc0000a93e0>] process_one_work+0x1f8/0x340
[<ffffffc0000a9784>] worker_thread+0x25c/0x448
[<ffffffc0000aedc8>] kthread+0xd0/0xd8
[<ffffffc000085550>] ret_from_fork+0x10/0x40
ath11k c000000.wifi: failed to perform regd update : -22
Invalid regulatory domain detected
To avoid this, the algorithm has to be changed slightly. Instead of
splitting a rule which overlaps with the weather radar range into 3 pieces
and accepting the first two parts blindly, it must actually be checked for
each piece whether it is a valid range. And only if it is valid, add it to
the output array.
When these checks are in place, the processed rules for AU would end up as
country AU: DFS-ETSI
(2400 - 2483 @ 40), (N/A, 36), (N/A)
(5150 - 5250 @ 80), (6, 23), (N/A), NO-OUTDOOR, AUTO-BW
(5250 - 5350 @ 80), (6, 20), (0 ms), NO-OUTDOOR, DFS, AUTO-BW
(5470 - 5590 @ 80), (6, 27), (0 ms), DFS, AUTO-BW
(5650 - 5730 @ 80), (6, 27), (0 ms), DFS, AUTO-BW
(5730 - 5850 @ 80), (6, 36), (N/A), AUTO-BW
and will be accepted by the wireless regulatory code.
Fixes: d5c65159f2 ("ath11k: driver for Qualcomm IEEE 802.11ax devices")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211112153116.1214421-1-sven@narfation.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3a56ef719f ]
Syzbot reported slab-out-of-bounds read in hci_le_adv_report_evt(). The
problem was in missing validaion check.
We should check if data is not malicious and we can read next data block.
If we won't check ptr validness, code can read a way beyond skb->end and
it can cause problems, of course.
Fixes: e95beb4141 ("Bluetooth: hci_le_adv_report_evt code refactoring")
Reported-and-tested-by: syzbot+e3fcb9c4f3c2a931dc40@syzkaller.appspotmail.com
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Oleksij Rempel
Bhupesh Sharma
Christophe JAILLET
Mansur Alisha Shaik
Philipp Zabel
Chen-Yu Tsai
Dafna Hirschfeld
Yang Yingliang
Fabio Estevam
Suresh Udipi
Hans de Goede
Daniel Scally
Eugen Hristev
Alan Maguire
Jan Kara
Claudiu Beznea
Tudor Ambarus
Peng Fan
Anilkumar Kolli
Giovanni Cabiddu
Marco Chiappero
Andrii Nakryiko
Dillon Min
Vladimir Zapolskiy
Lukasz Luba
George G. Davis
Prasad Malisetty
Chengfeng Ye
Wang Hai
Biju Das
Dan Carpenter
Lyude Paul
Alexander Aring
Jens Wiklander
oujiefeng
Karthikeyan Kathirvel
Sven Eckelmann
Pavel Skripkin
Lad Prabhakar