This patch fixes a bug in the image seq. number handling in the
scanning level. The assignment of the image_seq was incorrect.
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Do not forget to initialize 'gluebi->ubi_num' because otherwise
it will stay 0 even for ubi1 device, and gluebi will open
wrong UBI device when 'gluebi_get_device()' is called.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
The recent "UBI: fix NOR flash recovery" introduced compilation
warnings which were immediately spotted by our linux-next keeper.
This patch fixes them.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
This commit fixes NOR flash recovery issues observed with Spansion
S29GL512N NOR.
When NOR erases, it first fills PEBs with zeroes, then sets all bytes
to 0xFF. Filling with zeroes starts from the end of the PEB. And when
power is cut, this results in PEBs containing correct EC and VID headers
but corrupted with zeros at the end. This confuses UBI and it mistakinly
accepts these PEBs and associate them with LEBs.
Fis this issue by zeroing EC and VID magics before erasing PEBs, to
make UBI later refuse zem.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Move the image seq. number handling from I/O level to the scanning
lever, where it really belongs to. Move the @image_seq_set variable
to the @struct ubi_scan_info structure, which exists only during
scanning.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
An image sequence number is added to the UBI erase-counter header
to be able determine if the root file system contains a mixture
of old and new images (because the flashing failed to complete).
A change to nolo is also needed for this to take effect.
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
The 'paranoid_check_empty()' is bogus because, which is easilly
seen on NOR flash, which has long erase cycles, and which may
easilly end-up with half-erased eraseblocks. In this case the
paranoid check fails. I is just wrong to assume that PEBs which
do not have EC headers always contain all 0xFF. Such assumption
should not be made on the I/O level, which is quite low.
Thus, just kill the check.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
This patch adds code which makes sure eraseblocks contain all 0xFF
bytes before starting using them. The verification is done only when
debugging checks are enabled.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
We need to include jiffies.h manually in some cases, and the status
returned from omap_wait() was broken in two separate ways.
Also add cond_resched() to the loop.
Signed-off-by: Vimal Singh <vimalsingh@ti.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Use BLOCK_NIL consistently rather than sometimes 0xffff and sometimes
BLOCK_NIL.
The semantic patch that finds this issue is below
(http://www.emn.fr/x-info/coccinelle/). On the other hand, the changes
were made by hand, in part because drivers/mtd/inftlcore.c contains dead
code that causes spatch to ignore a relevant function. Specifically, the
function INFTL_findwriteunit contains a do-while loop, but always takes a
return that leaves the loop on the first iteration.
// <smpl>
@r exists@
identifier f,C;
@@
f(...) { ... return C; }
@s@
identifier r.C;
expression E;
@@
@@
identifier r.f,r.C,I;
expression s.E;
@@
f(...) {
<...
(
I
|
- E
+ C
)
...>
}
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The m25p16 data sheet from numonyx lists the worst-case bulk erase time
(tBE) as 40 seconds.
Signed-off-by: Steven A. Falco <sfalco@harris.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Commit 69423d99fc ("[MTD] update internal
API to support 64-bit device size") has changed some structure values
to 64-bit and has not updated this debug message, since it's not built
by default.
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@holoscopio.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
* git://git.infradead.org/mtd-2.6: (63 commits)
mtd: OneNAND: Allow setting of boundary information when built as module
jffs2: leaking jffs2_summary in function jffs2_scan_medium
mtd: nand: Fix memory leak on txx9ndfmc probe failure.
mtd: orion_nand: use burst reads with double word accesses
mtd/nand: s3c6400 support for s3c2410 driver
[MTD] [NAND] S3C2410: Use DIV_ROUND_UP
[MTD] [NAND] S3C2410: Deal with unaligned lengths in S3C2440 buffer read/write
[MTD] [NAND] S3C2410: Allow the machine code to get the BBT table from NAND
[MTD] [NAND] S3C2410: Added a kerneldoc for s3c2410_nand_set
mtd: physmap_of: Add multiple regions and concatenation support
mtd: nand: max_retries off by one in mxc_nand
mtd: nand: s3c2410_nand_setrate(): use correct macros for 2412/2440
mtd: onenand: add bbt_wait & unlock_all as replaceable for some platform
mtd: Flex-OneNAND support
mtd: nand: add OMAP2/OMAP3 NAND driver
mtd: maps: Blackfin async: fix memory leaks in probe/remove funcs
mtd: uclinux: mark local stuff static
mtd: uclinux: do not allow to be built as a module
mtd: uclinux: allow systems to override map addr/size
mtd: blackfin NFC: fix hang when using NAND on BF527-EZKITs
...
* 'linux-next' of git://git.infradead.org/ubi-2.6: (21 commits)
UBI: add reboot notifier
UBI: handle more error codes
UBI: fix multiple spelling typos
UBI: fix kmem_cache_free on error patch
UBI: print amount of reserved PEBs
UBI: improve messages in the WL worker
UBI: make gluebi a separate module
UBI: remove built-in gluebi
UBI: add notification API
UBI: do not switch to R/O mode on read errors
UBI: fix and clean-up error paths in WL worker
UBI: introduce new constants
UBI: fix race condition
UBI: minor serialization fix
UBI: do not panic if volume check fails
UBI: add dump_stack in checking code
UBI: fix races in I/O debugging checks
UBI: small debugging code optimization
UBI: improve debugging messages
UBI: re-name volumes_mutex to device_mutex
...
This patch unifies the flex_bdry setting for module vs. built-in
configuration of OneNAND.
Signed-off-by: Amul Kumar Saha <amul.saha@samsung.com>
Signed-off-by: Vishak G <vishak.g@samsung.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm: (417 commits)
MAINTAINERS: EB110ATX is not ebsa110
MAINTAINERS: update Eric Miao's email address and status
fb: add support of LCD display controller on pxa168/910 (base layer)
[ARM] 5552/1: ep93xx get_uart_rate(): use EP93XX_SYSCON_PWRCNT and EP93XX_SYSCON_PWRCN
[ARM] pxa/sharpsl_pm: zaurus needs generic pxa suspend/resume routines
[ARM] 5544/1: Trust PrimeCell resource sizes
[ARM] pxa/sharpsl_pm: cleanup of gpio-related code.
[ARM] pxa/sharpsl_pm: drop set_irq_type calls
[ARM] pxa/sharpsl_pm: merge pxa-specific code into generic one
[ARM] pxa/sharpsl_pm: merge the two sharpsl_pm.c since it's now pxa specific
[ARM] sa1100: remove unused collie_pm.c
[ARM] pxa: fix the conflicting non-static declarations of global_gpios[]
[ARM] 5550/1: Add default configure file for w90p910 platform
[ARM] 5549/1: Add clock api for w90p910 platform.
[ARM] 5548/1: Add gpio api for w90p910 platform
[ARM] 5551/1: Add multi-function pin api for w90p910 platform.
[ARM] Make ARM_VIC_NR depend on ARM_VIC
[ARM] 5546/1: ARM PL022 SSP/SPI driver v3
ARM: OMAP4: SMP: Update defconfig for OMAP4430
ARM: OMAP4: SMP: Enable SMP support for OMAP4430
...
.ko is normally not included in Kconfig help, make it consistent.
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The real 'armflash' map driver is selected by CONFIG_MTD_ARM_INTEGRATOR
Signed-off-by: Paulius Zaleckas <paulius.zaleckas@teltonika.lt>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
* 'for-2.6.31' of git://git.kernel.dk/linux-2.6-block: (153 commits)
block: add request clone interface (v2)
floppy: fix hibernation
ramdisk: remove long-deprecated "ramdisk=" boot-time parameter
fs/bio.c: add missing __user annotation
block: prevent possible io_context->refcount overflow
Add serial number support for virtio_blk, V4a
block: Add missing bounce_pfn stacking and fix comments
Revert "block: Fix bounce limit setting in DM"
cciss: decode unit attention in SCSI error handling code
cciss: Remove no longer needed sendcmd reject processing code
cciss: change SCSI error handling routines to work with interrupts enabled.
cciss: separate error processing and command retrying code in sendcmd_withirq_core()
cciss: factor out fix target status processing code from sendcmd functions
cciss: simplify interface of sendcmd() and sendcmd_withirq()
cciss: factor out core of sendcmd_withirq() for use by SCSI error handling code
cciss: Use schedule_timeout_uninterruptible in SCSI error handling code
block: needs to set the residual length of a bidi request
Revert "block: implement blkdev_readpages"
block: Fix bounce limit setting in DM
Removed reference to non-existing file Documentation/PCI/PCI-DMA-mapping.txt
...
Manually fix conflicts with tracing updates in:
block/blk-sysfs.c
drivers/ide/ide-atapi.c
drivers/ide/ide-cd.c
drivers/ide/ide-floppy.c
drivers/ide/ide-tape.c
include/trace/events/block.h
kernel/trace/blktrace.c
Terminate the UBI background thread prior to restarting the system.
[Artem: amended comments a little]
Signed-off-by: Kevin Cernekee <kpc.mtd@gmail.com>
Tested-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
The UBIFS WL worker may encounter read errors and there is logic
which makes a decision whether we should do one of:
1. cancel the operation and move the PEB with the read errors to
the 'erroneous' list;
2. switch to R/O mode.
ATM, only -EIO errors trigger 1., other errors trigger 2. The idea
is that if we know we encountered an I/O error, do 1. Otherwise,
we do not know how to react, and do 2., just in case. E.g., if
the underlying driver became crazy because of a bug, we do not
want to harm any data, and switch to R/O mode.
This patch does 2 things:
1. Makes sure reads from the source PEB always cause 1. This is
more consistent with other reads which come from the upper
layers and never cause R/O.
2. Teaches UBI to do 1. also on -EBADMSG, UBI_IO_BAD_VID_HDR,
-ENOMEM, and -ETIMEOUT. But this is only when reading the
target PEB.
This preblems were hunted by Adrian Hunter.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
'kmem_cache_free()' oopeses if NULL is passed, and there is
one error-path place where UBI may call it with NULL object.
This problem was pointed to by Adrian Hunter.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
When marking a PEB as bad, print how many PEBs are left reserved.
This is very useful information.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Commit 81933046ef ('mtd: Fix handling of
mtdname in txx9ndfmc.c') introduced a potential memory leak. The
'mtdname' member of the private data structure is now allocated
separately, but was not freed on certain error paths.
Fix that, and make things simpler by _always_ allocating it separately
so that we don't need 'if (mtdname != dev_name()) kfree(mtdname);'...
which gets ugly now that we're doing it more than once, and more likely
that we'll get it wrong some time.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This is not 8 times faster than byte access, but still around 60% faster.
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Add s3c6400 support to the s3c2410 driver. The nand controller in
the s3c64xx devices is compatible with the one in the s3c2412, so
simply reuse that code.
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Acked-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Add code to deal with fractional lengths, as reported by
Werner Almesberger. Re-work of his original patch.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Added a flag to allow the machine code to tell the NAND
subsystem that it should try to pickup a BBT from the flash,
and also skip the NAND full scan at startup.
Signed-off-by: Michel Pollet <buserror@gmail.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Print not only the PEB number, but also the LEB number and volume id,
which is very useful for bug hunting.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
This patch adds support to handle multiple non-identical chips in one
flash device tree node. It also adds concat support to physmap_of. This
makes it possible to support e.g. the Intel P30 48F4400 chips which
internally consists of 2 non-identical NOR chips on one die. Additionally
partitions now can span over multiple chips.
To describe such a chip's, multiple "reg" tuples are now supported in one
flash device tree node. Here an dts example:
flash@f0000000,0 {
#address-cells = <1>;
#size-cells = <1>;
compatible = "cfi-flash";
reg = <0 0x00000000 0x02000000
0 0x02000000 0x02000000>;
bank-width = <2>;
partition@0 {
label = "test-part1";
reg = <0 0x04000000>;
};
};
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
with `while (max_retries-- > 0)' max_retries reaches -1 after the loop.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Use the correct S3C2440_NFCONF_* macros for the mask for the 2412/2440
variants instead of the 2410 ones which use wrong bit positions.
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
DaVinci clock support has been updated in mainline.
Update clock names accordingly.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add bbt_wait & unlock_all as replaceable for some platform such as
s3c64xx s3c64xx has its own OneNAND controller and another interface
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Add support for Samsung Flex-OneNAND devices.
Flex-OneNAND combines SLC and MLC technologies into a single device.
SLC area provides increased reliability and speed, suitable for storing
code such as bootloader, kernel and root file system. MLC area
provides high density and is suitable for storing user data.
SLC and MLC regions can be configured through kernel parameter.
[akpm@linux-foundation.org: export flexoand_region and onenand_addr]
Signed-off-by: Rohit Hagargundgi <h.rohit@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Vishak G <vishak.g@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This driver is present in the OMAP tree, now pushing it to MTD.
Original author(s):
Jian Zhang <jzhang@ti.com>
Signed-off-by: Vimal Singh <vimalsingh@ti.com>
Cc: Jian Zhang <jzhang@ti.com>
Cc: Artem Bityutskiy <dedekind@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The uclinux_ram_mtdinfo, uclinux_romfs, and uclinux_point symbols do not
need to be visible outside of this module, so mark them static.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
CC: Greg Ungerer <gerg@uclinux.org>
CC: uclinux-dev@uclinux.org
CC: linux-mtd@lists.infradead.org
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
There isn't any benefit to building the uClinux MTD map as a module as the
rootfs it requires in order to actually be usable is appended to the
kernel image, not the module. No known system builds it this way either,
so change the option to "bool".
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
CC: Paul Mundt <lethal@linux-sh.org>
CC: Greg Ungerer <gerg@uclinux.org>
CC: uclinux-dev@uclinux.org
CC: linux-mtd@lists.infradead.org
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Due to a processor anomaly (05000263 to be exact), most Blackfin parts
cannot keep the embedded filesystem image directly after the kernel in
RAM. Instead, the filesystem needs to be relocated to the end of memory.
As such, we need to tweak the map addr/size during boot for Blackfin
systems. This can be done in any early arch/board init code.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
CC: Paul Mundt <lethal@linux-sh.org>
CC: Greg Ungerer <gerg@uclinux.org>
CC: uclinux-dev@uclinux.org
CC: linux-mtd@lists.infradead.org
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The DMAs have different bit sizes on BF52x and BF54x. From the PHRM:
"The 16-bit DMA Access Bus (DAB) connects the DMA controller to the
on-chip peripherals, PPI, SPI, Ethernet MAC, the SPORTs, NFC,
HOSTDP and the UARTs."
32-bit DMA won't work for BF52x.
Signed-off-by: Cliff Cai <cliff.cai@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Just add a new on-flash-bbt module parameter.
Signed-off-by: Simon Polette <spolette@adetelgroup.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Holger Brunck
Artem Bityutskiy
Adrian Hunter
vimal singh
Julia Lawall
Steven A. Falco
Thadeu Lima de Souza Cascardo
David Woodhouse
Linus Torvalds
Amul Saha
Pavel Machek
Paulius Zaleckas
Kevin Cernekee
Atsushi Nemoto
Russell King
Nicolas Pitre
Peter Korsgaard
Ben Dooks
Michel Pollet
Stefan Roese
Roel Kluin
Kevin Hilman
Kyungmin Park
Rohit Hagargundgi
Mike Frysinger
Cliff Cai
Simon Polette