Add driver for IDT VersaClock 5 5P49V5923 and 5P49V5933 chips. These
chips have two clock inputs, XTAL or CLK, which are muxed into single
PLL/VCO input. In case of 5P49V5923, the XTAL in built into the chip
while the 5P49V5923 requires external XTAL.
The PLL feeds two fractional dividers. Each fractional divider feeds
output mux, which allows selecting between clock from the fractional
divider itself or from output mux on output N-1. In case of output
mux 0, the output N-1 is instead connected to the output from the mux
feeding the PLL.
The driver thus far supports only the 5P49V5923 and 5P49V5933, while
it should be easily extensible to the whole 5P49V59xx family of chips
as they are all pretty similar.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Michael Turquette <mturquette@baylibre.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Tested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: linux-renesas-soc@vger.kernel.org
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The CDCE925 is a member of the CDCE(L)9xx programmable clock generator
family. There are also CDCE913, CDCE937, CDCE949 which have different
number of PLLs and outputs.
The clk-cdce925 driver supports only CDCE925 in the family. This adds
support for the CDCE913, CDCE937, CDCE949, too.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Cc: Mike Looijmans <mike.looijmans@topic.nl>
Cc: Michael Turquette <mturquette@linaro.org>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
s2mps11 and max77686 clock drivers can be compile tested to increase
build coverage.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
This includes UniPhier clock driver code, except SoC-specific
data arrays.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Add a Kconfig to define clock configuration for each SoC, and
modify the Makefile to build drivers that only selected in config.
Signed-off-by: Shunli Wang <shunli.wang@mediatek.com>
Signed-off-by: James Liao <jamesjj.liao@mediatek.com>
Signed-off-by: Erin Lo <erin.lo@mediatek.com>
Tested-by: John Crispin <blogic@openwrt.org>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Maxim Max77620 has one 32KHz clock output and the clock HW
IP used on this PMIC is same as what it is there in the MAX77686.
Add clock driver support for MAX77620 on the MAX77686 driver.
CC: Krzysztof Kozlowski <k.kozlowski@samsung.com>
CC: Javier Martinez Canillas <javier@dowhile0.org>
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Tested-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The clock IP used on the Maxim PMICs max77686 and max77802 are
same. The configuration of clock register is also same except
the number of clocks.
Part of common code utilisation, there is 3 files for these chips
clock driver, one for common and two files for driver registration.
Combine both drivers into single file and move common code into
same common file reduces the 2 files and make max77686 and max77802
clock driver in single fine. This driver does not depends on the
parent driver structure. The regmap handle is acquired through
regmap APIs for the register access.
This combination of driver helps on adding clock driver for different
Maxim PMICs which has similar clock IP like MAX77620 and MAX20024.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
CC: Krzysztof Kozlowski <k.kozlowski@samsung.com>
CC: Javier Martinez Canillas <javier@dowhile0.org>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Tested-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The clk-oxnas driver is specific to its architecture, so do not
propose it on other architectures, unless build-testing.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
Link: lkml.kernel.org/r/20160707091844.196a7930@endymion
Start our new clock infrastructure by adding the registration code, common
structure and common code.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
Link: lkml.kernel.org/r/20160629190535.11855-3-maxime.ripard@free-electrons.com
The RK808 and RK818 PMICs are using a similar register map.
We can reuse the clk driver for the RK818 PMIC. So let's add
the RK818 in the Kconfig description.
Signed-off-by: Wadim Egorov <w.egorov@phytec.de>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
Link: lkml.kernel.org/r/1464850228-17244-4-git-send-email-w.egorov@phytec.de
Break the AmLogic clock code up so that only the necessary parts are
compiled and linked. The core code is selected by both arm and arm64
builds with COMMON_CLK_AMLOGIC. The individual drivers have their own
config options as well.
Tested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
do have a couple core changes in here as well.
Core:
- CLK_IS_CRITICAL support has been added. This should allow drivers
to properly express that a certain clk should stay on even if
their prepare/enable count drops to 0 (and in turn the parents of
these clks should stay enabled).
- A clk registration API has been added, clk_hw_register(), and
an OF clk provider API has been added, of_clk_add_hw_provider().
These APIs have been put in place to further split clk providers
from clk consumers, with the goal being to have clk providers
never deal with struct clk pointers at all. Conversion of provider
drivers is on going. clkdev has also gained support for registering
clk_hw pointers directly so we can convert drivers that don't use
devicetree.
New Drivers:
- Marvell ap806 and cp110 system controllers (with clks inside!)
- Hisilicon Hi3519 clock and reset controller
- Axis ARTPEC-6 clock controllers
- Oxford Semiconductor OXNAS clock controllers
- AXS10X I2S PLL
- Rockchip RK3399 clock and reset controller
Updates:
- MMC2 and UART2 clks on Samsung Exynos 3250, ACLK on Samsung Exynos 542x
SoCs, and some more clk ID exporting for bus frequency scaling
- Proper BCM2835 PCM clk support and various other clks
- i.MX clk updates for i.MX6SX, i.MX7, and VF610
- Renesas updates for R-Car H3
- Tegra210 got updates for DisplayPort and HDMI 2.0
- Rockchip driver refactorings and fixes due to adding RK3399 support
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQIcBAABCAAGBQJXP7QdAAoJEK0CiJfG5JUl/Q8P/i93QXTom/VbwDHZ4DDZr0Hc
69oCRVTDTArGLa4YrGMxu3crNWf8/ORwsZVG93PD6bkkrWo9qH52KFsI22MdZcta
HlApsFjI503C7qDw6V8UVz7mUJVfarCxKNSd1WBPCVCNExarIrRRymC3NXT6ZrUP
D59E53d4G+I6OUuybsp4gtA7aEoYebAE7BInPDDihIk7Lall5mLYbfJUumpHlmSd
wqqPad5OYoC1nkrYhIGficK9Bizy3eyK829EoqpQpE4djkNhEwKd/AwSJZ6i1pdC
obt8vQyPRK0ByND2I+3XPqZ7bFb9IKu5WIAkYzG8QskFyIqiFtOkFgEP360ojlGT
D8sZY7RBmIM4Tu5RgeoN94wML4f/zYOm6YzVUVjWdVPGoxuy4QhQsvS5Id70ifNU
pSYf1KG0Gq0wvptth02zaDE9r1lDMOCHsOPIbVMqHRxRj8shUyjroTEzdtdyS6SE
FsYmGdrq4YctXyP4E8efLzFMjN7qZyKgnAoGfROsPRb6NE3DSFs5PcxQldOcoBPv
+NstBGUlJ4Xzwd1BdxKWJq8aIsG/CLqTec63OYSYM0bfUSWXKOgemvBV8MJrDP1D
rFabdJVHhUZOy5UgxOdfmy1XWp/SWup8OUnpEJp84RywGP6UMM0s1RtWruMJ776J
tBzVIIYCJrAWFia0Djlr
=aEzb
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk updates from Stephen Boyd:
"It's the usual big pile of driver updates and additions, but we do
have a couple core changes in here as well.
Core:
- CLK_IS_CRITICAL support has been added. This should allow drivers
to properly express that a certain clk should stay on even if their
prepare/enable count drops to 0 (and in turn the parents of these
clks should stay enabled).
- A clk registration API has been added, clk_hw_register(), and an OF
clk provider API has been added, of_clk_add_hw_provider(). These
APIs have been put in place to further split clk providers from clk
consumers, with the goal being to have clk providers never deal
with struct clk pointers at all. Conversion of provider drivers is
on going. clkdev has also gained support for registering clk_hw
pointers directly so we can convert drivers that don't use
devicetree.
New Drivers:
- Marvell ap806 and cp110 system controllers (with clks inside!)
- Hisilicon Hi3519 clock and reset controller
- Axis ARTPEC-6 clock controllers
- Oxford Semiconductor OXNAS clock controllers
- AXS10X I2S PLL
- Rockchip RK3399 clock and reset controller
Updates:
- MMC2 and UART2 clks on Samsung Exynos 3250, ACLK on Samsung Exynos
542x SoCs, and some more clk ID exporting for bus frequency scaling
- Proper BCM2835 PCM clk support and various other clks
- i.MX clk updates for i.MX6SX, i.MX7, and VF610
- Renesas updates for R-Car H3
- Tegra210 got updates for DisplayPort and HDMI 2.0
- Rockchip driver refactorings and fixes due to adding RK3399 support"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (139 commits)
clk: fix critical clock locking
clk: qcom: mmcc-8996: Remove clocks that should be controlled by RPM
clk: ingenic: Allow divider value to be divided
clk: sunxi: Add display and TCON0 clocks driver
clk: rockchip: drop old_rate calculation on pll rate changes
clk: rockchip: simplify GRF handling in pll clocks
clk: rockchip: lookup General Register Files in rockchip_clk_init
clk: rockchip: fix the rk3399 sdmmc sample / drv name
clk: mvebu: new driver for Armada CP110 system controller
dt-bindings: arm: add DT binding for Marvell CP110 system controller
clk: mvebu: new driver for Armada AP806 system controller
clk: hisilicon: add CRG driver for hi3519 soc
clk: hisilicon: export some hisilicon APIs to modules
reset: hisilicon: add reset controller driver for hisilicon SOCs
clk: bcm/kona: Do not use sizeof on pointer type
clk: qcom: msm8916: Fix crypto clock flags
clk: nxp: lpc18xx: Initialize clk_init_data::flags to 0
clk/axs10x: Add I2S PLL clock driver
clk: imx7d: fix ahb clock mux 1
clk: fix comment of devm_clk_hw_register()
...
Pull MIPS updates from Ralf Baechle:
"This is the main pull request for MIPS for 4.7. Here's the summary of
the changes:
- ATH79: Support for DTB passuing using the UHI boot protocol
- ATH79: Remove support for builtin DTB.
- ATH79: Add zboot debug serial support.
- ATH79: Add initial support for Dragino MS14 (Dragine 2), Onion Omega
and DPT-Module.
- ATH79: Update devicetree clock support for AR9132 and AR9331.
- ATH79: Cleanup the DT code.
- ATH79: Support newer SOCs in ath79_ddr_ctrl_init.
- ATH79: Fix regression in PCI window initialization.
- BCM47xx: Move SPROM driver to drivers/firmware/
- BCM63xx: Enable partition parser in defconfig.
- BMIPS: BMIPS5000 has I cache filing from D cache
- BMIPS: BMIPS: Add cpu-feature-overrides.h
- BMIPS: Add Whirlwind support
- BMIPS: Adjust mips-hpt-frequency for BCM7435
- BMIPS: Remove maxcpus from BCM97435SVMB DTS
- BMIPS: Add missing 7038 L1 register cells to BCM7435
- BMIPS: Various tweaks to initialization code.
- BMIPS: Enable partition parser in defconfig.
- BMIPS: Cache tweaks.
- BMIPS: Add UART, I2C and SATA devices to DT.
- BMIPS: Add BCM6358 and BCM63268support
- BMIPS: Add device tree example for BCM6358.
- BMIPS: Improve Improve BCM6328 and BCM6368 device trees
- Lantiq: Add support for device tree file from boot loader
- Lantiq: Allow build with no built-in DT.
- Loongson 3: Reserve 32MB for RS780E integrated GPU.
- Loongson 3: Fix build error after ld-version.sh modification
- Loongson 3: Move chipset ACPI code from drivers to arch.
- Loongson 3: Speedup irq processing.
- Loongson 3: Add basic Loongson 3A support.
- Loongson 3: Set cache flush handlers to nop.
- Loongson 3: Invalidate special TLBs when needed.
- Loongson 3: Fast TLB refill handler.
- MT7620: Fallback strategy for invalid syscfg0.
- Netlogic: Fix CP0_EBASE redefinition warnings
- Octeon: Initialization fixes
- Octeon: Add DTS files for the D-Link DSR-1000N and EdgeRouter Lite
- Octeon: Enable add Octeon-drivers in cavium_octeon_defconfig
- Octeon: Correctly handle endian-swapped initramfs images.
- Octeon: Support CN73xx, CN75xx and CN78xx.
- Octeon: Remove dead code from cvmx-sysinfo.
- Octeon: Extend number of supported CPUs past 32.
- Octeon: Remove some code limiting NR_IRQS to 255.
- Octeon: Simplify octeon_irq_ciu_gpio_set_type.
- Octeon: Mark some functions __init in smp.c
- Octeon: Octeon: Add Octeon III CN7xxx interface detection
- PIC32: Add serial driver and bindings for it.
- PIC32: Add PIC32 deadman timer driver and bindings.
- PIC32: Add PIC32 clock timer driver and bindings.
- Pistachio: Determine SoC revision during boot
- Sibyte: Fix Kconfig dependencies of SIBYTE_BUS_WATCHER.
- Sibyte: Strip redundant comments from bcm1480_regs.h.
- Panic immediately if panic_on_oops is set.
- module: fix incorrect IS_ERR_VALUE macro usage.
- module: Make consistent use of pr_*
- Remove no longer needed work_on_cpu() call.
- Remove CONFIG_IPV6_PRIVACY from defconfigs.
- Fix registers of non-crashing CPUs in dumps.
- Handle MIPSisms in new vmcore_elf32_check_arch.
- Select CONFIG_HANDLE_DOMAIN_IRQ and make it work.
- Allow RIXI to be used on non-R2 or R6 cores.
- Reserve nosave data for hibernation
- Fix siginfo.h to use strict POSIX types.
- Don't unwind user mode with EVA.
- Fix watchpoint restoration
- Ptrace watchpoints for R6.
- Sync icache when it fills from dcache
- I6400 I-cache fills from dcache.
- Various MSA fixes.
- Cleanup MIPS_CPU_* definitions.
- Signal: Move generic copy_siginfo to signal.h
- Signal: Fix uapi include in exported asm/siginfo.h
- Timer fixes for sake of KVM.
- XPA TLB refill fixes.
- Treat perf counter feature
- Update John Crispin's email address
- Add PIC32 watchdog and bindings.
- Handle R10000 LL/SC bug in set_pte()
- cpufreq: Various fixes for Longson1.
- R6: Fix R2 emulation.
- mathemu: Cosmetic fix to ADDIUPC emulation, plenty of other small fixes
- ELF: ABI and FP fixes.
- Allow for relocatable kernel and use that to support KASLR.
- Fix CPC_BASE_ADDR mask
- Plenty fo smp-cps, CM, R6 and M6250 fixes.
- Make reset_control_ops const.
- Fix kernel command line handling of leading whitespace.
- Cleanups to cache handling.
- Add brcm, bcm6345-l1-intc device tree bindings.
- Use generic clkdev.h header
- Remove CLK_IS_ROOT usage.
- Misc small cleanups.
- CM: Fix compilation error when !MIPS_CM
- oprofile: Fix a preemption issue
- Detect DSP ASE v3 support:1"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (275 commits)
MIPS: pic32mzda: fix getting timer clock rate.
MIPS: ath79: fix regression in PCI window initialization
MIPS: ath79: make ath79_ddr_ctrl_init() compatible for newer SoCs
MIPS: Fix VZ probe gas errors with binutils <2.24
MIPS: perf: Fix I6400 event numbers
MIPS: DEC: Export `ioasic_ssr_lock' to modules
MIPS: MSA: Fix a link error on `_init_msa_upper' with older GCC
MIPS: CM: Fix compilation error when !MIPS_CM
MIPS: Fix genvdso error on rebuild
USB: ohci-jz4740: Remove obsolete driver
MIPS: JZ4740: Probe OHCI platform device via DT
MIPS: JZ4740: Qi LB60: Remove support for AVT2 variant
MIPS: pistachio: Determine SoC revision during boot
MIPS: BMIPS: Adjust mips-hpt-frequency for BCM7435
mips: mt7620: fallback to SDRAM when syscfg0 does not have a valid value for the memory type
MIPS: Prevent "restoration" of MSA context in non-MSA kernels
MIPS: cevt-r4k: Dynamically calculate min_delta_ns
MIPS: malta-time: Take seconds into account
MIPS: malta-time: Start GIC count before syncing to RTC
MIPS: Force CPUs to lose FP context during mode switches
...
Add Oxford Semiconductor OXNAS SoC Family Standard Clocks support.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
[sboyd@codeaurora.org: Drop NULL/continue check in registration
loop]
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Currently the decision whether to build the renesas-cpg-mssr and
clk-mstp drivers is handled by Makefile logic. However, the rcar-sysc
driver will need to know whether CPG/MSSR and/or CPG/MSTP support are
available or not.
To avoid having to duplicate this logic, move it to Kconfig. Provide
non-visible CLK_RENESAS_CPG_MSSR and CLK_RENESAS_CPG_MSTP Kconfig
symbols, which can be used by both Makefiles and C code.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
On dm814x we have 13 ADPLLs with 3 to 4 outputs on each. The
ADPLLs have several dividers and muxes controlled by a shared
control register for each PLL.
Note that for the clocks to work as device drivers for booting on
dm814x, this patch depends on "ARM: OMAP2+: Change core_initcall
levels to postcore_initcall" that has already been merged.
Also note that this patch does not implement clk_set_rate for the
PLL, that will be posted later on when available.
Cc: Stephen Boyd <sboyd@codeaurora.org>
Acked-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
This config was used for the ARM port so that it could use a
machine specific clkdev.h include, but those are all gone now.
The MIPS architecture is the last user, and from what I can tell
it doesn't actually use it anyway, so let's remove the config all
together.
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: <linux-mips@linux-mips.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Reviewed-by: Joshua Henderson <joshua.henderson@microchip.com>
There are two TI CDCE clock chips in this file. Move them close
together so they're easier to find.
No functional change, just cosmetic.
Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
[sboyd@codeaurora.org: Alphabetize]
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Move all vendor's Kconfig into CCF menu section to prevent
new drivers putting their Kconfig files in a wrong place.
Some Kconfigs need to be modified at the same time to avoid build
warnings.
Signed-off-by: James Liao <jamesjj.liao@mediatek.com>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
[sboyd@codeaurora.org: Fix typos in commit message]
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Presumably the second COMMON_CLK_NXP config option in
drivers/clk/Kconfig appeared after a merge conflict resolution, remove
the wrong record of two.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
Add support for all configurable clocks found on NXP LPC32xx SoC.
The list contains several heterogenous groups of clocks:
* system clocks including multiple dividers and muxes,
* x397 PLL, HCLK PLL and USB PLL,
* peripheral clocks inherited from rtc, hclk and pclk,
* USB controller clocks: AHB slave, I2C, OTG, OHCI and device.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
The change adds COMMON_CLK_NXP configuration symbol and enables it for
NXP LPC18XX architecture, this is needed to reuse drivers/clk/nxp
folder for NXP common clock framework drivers other than LPC18XX one.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Acked-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
As we've enabled multiplatform kernels on ARM, and greatly done away with
the contents under arch/arm/mach-*, there's still need for SoC-related
drivers to go somewhere.
Many of them go in through other driver trees, but we still have
drivers/soc to hold some of the "doesn't fit anywhere" lowlevel code
that might be shared between ARM and ARM64 (or just in general makes
sense to not have under the architecture directory).
This branch contains mostly such code:
- Drivers for qualcomm SoCs for SMEM, SMD and SMD-RPM, used to communicate
with power management blocks on these SoCs for use by clock, regulator and
bus frequency drivers.
- Allwinner Reduced Serial Bus driver, again used to communicate with PMICs.
- Drivers for ARM's SCPI (System Control Processor). Not to be confused with
PSCI (Power State Coordination Interface). SCPI is used to communicate with
the assistant embedded cores doing power management, and we have yet to see
how many of them will implement this for their hardware vs abstracting in
other ways (or not at all like in the past).
- To make confusion between SCPI and PSCI more likely, this release also
includes an update of PSCI to interface version 1.0.
- Rockchip support for power domains.
- A driver to talk to the firmware on Raspberry Pi.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJWQC+cAAoJEIwa5zzehBx3jEUP/0GpxfDVanEUkudVLLe7J0RH
CNlRan107Cw6hXRUJo7elEsuCALjccXjc1CAH4+RnNpOAeBKW97n+WU7trTv+wUZ
sQX4SkBPKFBlgwGF2qhsi5q74gms/BrgtCa4kNb9joOYso039tlfIOPzK80DMkOm
TkyIJdUCgFJMjCQLhX6kGT0PDcrbIjb6aA2cF3FAVeaJA7uz8lNe/eHJr3oHxIEY
CvC651yJ2mIHQUU4BJx/AJo+wXg3dRUXNCAtBjwLRPEAzduYZXYm1ZTVIby/1q9r
dR2KDFEuibODXmXrDBzKNJwCu/TLJEwo/1oPaEIVfY91XLKfiWUhgVqa1o1I+d9U
XoGPibCW461qFahjQW87MfInALpCOA7/RbTNjFp+MVyipCYvkaYq7KFiYEldgFDx
z4Qx/J4hYc2TlDWrpNiUCZMfmhwi7y+Ib+tnenYTO1eyMuw0e9mfnVdjk5iU3Pvk
Ye4qPqpYclJruyHbYi164878+1lLaW2NCUgC3rkBO/GWPAzp7d9iLWoZ3PuyD5i5
PEjs668UcRdZYbI4rdrhGHL8Eq9Gnuc4Rthu7HxPOK+DG0XgP8r97PhM8aYGYVDO
+yikBtjWRsA9fPj3rMKA3UsQ61DAeR9LmZ0XPGjWFMCjCG0JlUoIMaA+Uu0i8fr8
95qxBVxbO7rhL39r1rhV
=dm+I
-----END PGP SIGNATURE-----
Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver updates from Olof Johansson:
"As we've enabled multiplatform kernels on ARM, and greatly done away
with the contents under arch/arm/mach-*, there's still need for
SoC-related drivers to go somewhere.
Many of them go in through other driver trees, but we still have
drivers/soc to hold some of the "doesn't fit anywhere" lowlevel code
that might be shared between ARM and ARM64 (or just in general makes
sense to not have under the architecture directory).
This branch contains mostly such code:
- Drivers for qualcomm SoCs for SMEM, SMD and SMD-RPM, used to
communicate with power management blocks on these SoCs for use by
clock, regulator and bus frequency drivers.
- Allwinner Reduced Serial Bus driver, again used to communicate with
PMICs.
- Drivers for ARM's SCPI (System Control Processor). Not to be
confused with PSCI (Power State Coordination Interface). SCPI is
used to communicate with the assistant embedded cores doing power
management, and we have yet to see how many of them will implement
this for their hardware vs abstracting in other ways (or not at all
like in the past).
- To make confusion between SCPI and PSCI more likely, this release
also includes an update of PSCI to interface version 1.0.
- Rockchip support for power domains.
- A driver to talk to the firmware on Raspberry Pi"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (57 commits)
soc: qcom: smd-rpm: Correct size of outgoing message
bus: sunxi-rsb: Add driver for Allwinner Reduced Serial Bus
bus: sunxi-rsb: Add Allwinner Reduced Serial Bus (RSB) controller bindings
ARM: bcm2835: add mutual inclusion protection
drivers: psci: make PSCI 1.0 functions initialization version dependent
dt-bindings: Correct paths in Rockchip power domains binding document
soc: rockchip: power-domain: don't try to print the clock name in error case
soc: qcom/smem: add HWSPINLOCK dependency
clk: berlin: add cpuclk
ARM: berlin: dts: add CLKID_CPU for BG2Q
ARM: bcm2835: Add the Raspberry Pi firmware driver
soc: qcom: smem: Move RPM message ram out of smem DT node
soc: qcom: smd-rpm: Correct the active vs sleep state flagging
soc: qcom: smd: delete unneeded of_node_put
firmware: qcom-scm: build for correct architecture level
soc: qcom: smd: Correct SMEM items for upper channels
qcom-scm: add missing prototype for qcom_scm_is_available()
qcom-scm: fix endianess issue in __qcom_scm_is_call_available
soc: qcom: smd: Reject send of too big packets
soc: qcom: smd: Handle big endian CPUs
...
- Kconfig: remove BE-only platforms from LE kernel build from Boqun Feng
- Refresh ps3_defconfig from Geoff Levand
- Emit GNU & SysV hashes for the vdso from Michael Ellerman
- Define an enum for the bolted SLB indexes from Anshuman Khandual
- Use a local to avoid multiple calls to get_slb_shadow() from Michael Ellerman
- Add gettimeofday() benchmark from Michael Neuling
- Avoid link stack corruption in __get_datapage() from Michael Neuling
- Add virt_to_pfn and use this instead of opencoding from Aneesh Kumar K.V
- Add ppc64le_defconfig from Michael Ellerman
- pseries: extract of_helpers module from Andy Shevchenko
- Correct string length in pseries_of_derive_parent() from Nathan Fontenot
- Free the MSI bitmap if it was slab allocated from Denis Kirjanov
- Shorten irq_chip name for the SIU from Christophe Leroy
- Wait 1s for secondaries to enter OPAL during kexec from Samuel Mendoza-Jonas
- Fix _ALIGN_* errors due to type difference. from Aneesh Kumar K.V
- powerpc/pseries/hvcserver: don't memset pi_buff if it is null from Colin Ian King
- Disable hugepd for 64K page size. from Aneesh Kumar K.V
- Differentiate between hugetlb and THP during page walk from Aneesh Kumar K.V
- Make PCI non-optional for pseries from Michael Ellerman
- Individual System V IPC system calls from Sam bobroff
- Add selftest of unmuxed IPC calls from Michael Ellerman
- discard .exit.data at runtime from Stephen Rothwell
- Delete old orphaned PrPMC 280/2800 DTS and boot file. from Paul Gortmaker
- Use of_get_next_parent to simplify code from Christophe Jaillet
- Paginate some xmon output from Sam bobroff
- Add some more elements to the xmon PACA dump from Michael Ellerman
- Allow the tm-syscall selftest to build with old headers from Michael Ellerman
- Run EBB selftests only on POWER8 from Denis Kirjanov
- Drop CONFIG_TUNE_CELL in favour of CONFIG_CELL_CPU from Michael Ellerman
- Avoid reference to potentially freed memory in prom.c from Christophe Jaillet
- Quieten boot wrapper output with run_cmd from Geoff Levand
- EEH fixes and cleanups from Gavin Shan
- Fix recursive fenced PHB on Broadcom shiner adapter from Gavin Shan
- Use of_get_next_parent() in of_get_ibm_chip_id() from Michael Ellerman
- Fix section mismatch warning in msi_bitmap_alloc() from Denis Kirjanov
- Fix ps3-lpm white space from Rudhresh Kumar J
- Fix ps3-vuart null dereference from Colin King
- nvram: Add missing kfree in error path from Christophe Jaillet
- nvram: Fix function name in some errors messages. from Christophe Jaillet
- drivers/macintosh: adb: fix misleading Kconfig help text from Aaro Koskinen
- agp/uninorth: fix a memleak in create_gatt_table from Denis Kirjanov
- cxl: Free virtual PHB when removing from Andrew Donnellan
- scripts/kconfig/Makefile: Allow KBUILD_DEFCONFIG to be a target from Michael Ellerman
- scripts/kconfig/Makefile: Fix KBUILD_DEFCONFIG check when building with O= from Michael Ellerman
- Freescale updates from Scott: Highlights include 64-bit book3e kexec/kdump
support, a rework of the qoriq clock driver, device tree changes including
qoriq fman nodes, support for a new 85xx board, and some fixes.
- MPC5xxx updates from Anatolij: Highlights include a driver for MPC512x
LocalPlus Bus FIFO with its device tree binding documentation, mpc512x
device tree updates and some minor fixes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=YwcM
-----END PGP SIGNATURE-----
Merge tag 'powerpc-4.4-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc updates from Michael Ellerman:
- Kconfig: remove BE-only platforms from LE kernel build from Boqun
Feng
- Refresh ps3_defconfig from Geoff Levand
- Emit GNU & SysV hashes for the vdso from Michael Ellerman
- Define an enum for the bolted SLB indexes from Anshuman Khandual
- Use a local to avoid multiple calls to get_slb_shadow() from Michael
Ellerman
- Add gettimeofday() benchmark from Michael Neuling
- Avoid link stack corruption in __get_datapage() from Michael Neuling
- Add virt_to_pfn and use this instead of opencoding from Aneesh Kumar
K.V
- Add ppc64le_defconfig from Michael Ellerman
- pseries: extract of_helpers module from Andy Shevchenko
- Correct string length in pseries_of_derive_parent() from Nathan
Fontenot
- Free the MSI bitmap if it was slab allocated from Denis Kirjanov
- Shorten irq_chip name for the SIU from Christophe Leroy
- Wait 1s for secondaries to enter OPAL during kexec from Samuel
Mendoza-Jonas
- Fix _ALIGN_* errors due to type difference, from Aneesh Kumar K.V
- powerpc/pseries/hvcserver: don't memset pi_buff if it is null from
Colin Ian King
- Disable hugepd for 64K page size, from Aneesh Kumar K.V
- Differentiate between hugetlb and THP during page walk from Aneesh
Kumar K.V
- Make PCI non-optional for pseries from Michael Ellerman
- Individual System V IPC system calls from Sam bobroff
- Add selftest of unmuxed IPC calls from Michael Ellerman
- discard .exit.data at runtime from Stephen Rothwell
- Delete old orphaned PrPMC 280/2800 DTS and boot file, from Paul
Gortmaker
- Use of_get_next_parent to simplify code from Christophe Jaillet
- Paginate some xmon output from Sam bobroff
- Add some more elements to the xmon PACA dump from Michael Ellerman
- Allow the tm-syscall selftest to build with old headers from Michael
Ellerman
- Run EBB selftests only on POWER8 from Denis Kirjanov
- Drop CONFIG_TUNE_CELL in favour of CONFIG_CELL_CPU from Michael
Ellerman
- Avoid reference to potentially freed memory in prom.c from Christophe
Jaillet
- Quieten boot wrapper output with run_cmd from Geoff Levand
- EEH fixes and cleanups from Gavin Shan
- Fix recursive fenced PHB on Broadcom shiner adapter from Gavin Shan
- Use of_get_next_parent() in of_get_ibm_chip_id() from Michael
Ellerman
- Fix section mismatch warning in msi_bitmap_alloc() from Denis
Kirjanov
- Fix ps3-lpm white space from Rudhresh Kumar J
- Fix ps3-vuart null dereference from Colin King
- nvram: Add missing kfree in error path from Christophe Jaillet
- nvram: Fix function name in some errors messages, from Christophe
Jaillet
- drivers/macintosh: adb: fix misleading Kconfig help text from Aaro
Koskinen
- agp/uninorth: fix a memleak in create_gatt_table from Denis Kirjanov
- cxl: Free virtual PHB when removing from Andrew Donnellan
- scripts/kconfig/Makefile: Allow KBUILD_DEFCONFIG to be a target from
Michael Ellerman
- scripts/kconfig/Makefile: Fix KBUILD_DEFCONFIG check when building
with O= from Michael Ellerman
- Freescale updates from Scott: Highlights include 64-bit book3e
kexec/kdump support, a rework of the qoriq clock driver, device tree
changes including qoriq fman nodes, support for a new 85xx board, and
some fixes.
- MPC5xxx updates from Anatolij: Highlights include a driver for
MPC512x LocalPlus Bus FIFO with its device tree binding
documentation, mpc512x device tree updates and some minor fixes.
* tag 'powerpc-4.4-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (106 commits)
powerpc/msi: Fix section mismatch warning in msi_bitmap_alloc()
powerpc/prom: Use of_get_next_parent() in of_get_ibm_chip_id()
powerpc/pseries: Correct string length in pseries_of_derive_parent()
powerpc/e6500: hw tablewalk: make sure we invalidate and write to the same tlb entry
powerpc/mpc85xx: Add FSL QorIQ DPAA FMan support to the SoC device tree(s)
powerpc/mpc85xx: Create dts components for the FSL QorIQ DPAA FMan
powerpc/fsl: Add #clock-cells and clockgen label to clockgen nodes
powerpc: handle error case in cpm_muram_alloc()
powerpc: mpic: use IRQCHIP_SKIP_SET_WAKE instead of redundant mpic_irq_set_wake
powerpc/book3e-64: Enable kexec
powerpc/book3e-64/kexec: Set "r4 = 0" when entering spinloop
powerpc/booke: Only use VIRT_PHYS_OFFSET on booke32
powerpc/book3e-64/kexec: Enable SMP release
powerpc/book3e-64/kexec: create an identity TLB mapping
powerpc/book3e-64: Don't limit paca to 256 MiB
powerpc/book3e/kdump: Enable crash_kexec_wait_realmode
powerpc/book3e: support CONFIG_RELOCATABLE
powerpc/booke64: Fix args to copy_and_flush
powerpc/book3e-64: rename interrupt_end_book3e with __end_interrupts
powerpc/e6500: kexec: Handle hardware threads
...
LS2080A is the first implementation of the chassis 3 clockgen, which
has a different register layout than previous chips. It is also little
endian, unlike previous chips.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
These drivers only have runtime but no build time dependencies so can be
built for testing purposes if the Kconfig COMPILE_TEST option is enabled.
This is useful to have more build coverage and make sure that drivers are
not affected by changes that could cause build regressions.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Scott Branden <sbranden@broadcom.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
This patch adds the driver and devicetree documentation for the
Silicon Labs SI514 clock generator chip. This is an I2C controlled
oscillator capable of generating clock signals ranging from 100kHz
to 250MHz.
Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
[sboyd@codeaurora.org: Drop clk.h include, remove some casts]
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
This patch converts the code to use rational best approximation algorithm which
is much more precise.
Suggested-by: Stephen Boyd <sboyd@codeaurora.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
On some ARM based systems, a separate Cortex-M based System Control
Processor(SCP) provides the overall power, clock, reset and system
control. System Control and Power Interface(SCPI) Message Protocol
is defined for the communication between the Application Cores(AP)
and the SCP.
This patch adds support for the clocks provided by SCP using SCPI
protocol.
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Cc: Mike Turquette <mturquette@baylibre.com>
Cc: Liviu Dudau <Liviu.Dudau@arm.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Jon Medhurst (Tixy) <tixy@linaro.org>
Cc: linux-clk@vger.kernel.org
This contains the EMC clock driver that's been exhaustively reviewed and
tested. It also includes a change to the clock core that allows a clock
provider to perform low-level reparenting of clocks. This is required by
the EMC clock driver because the reparenting needs to be done at a very
specific point in time during the EMC frequency switch.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=I0gO
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-4.2-clk' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into clk-next
clk: tegra: Changes for v4.2-rc1
This contains the EMC clock driver that's been exhaustively reviewed and
tested. It also includes a change to the clock core that allows a clock
provider to perform low-level reparenting of clocks. This is required by
the EMC clock driver because the reparenting needs to be done at a very
specific point in time during the EMC frequency switch.
This driver supports the TI CDCE925 programmable clock synthesizer.
The chip contains two PLLs with spread-spectrum clocking support and
five output dividers. The driver only supports the following setup,
and uses a fixed setting for the output muxes:
Y1 is derived from the input clock
Y2 and Y3 derive from PLL1
Y4 and Y5 derive from PLL2
Given a target output frequency, the driver will set the PLL and
divider to best approximate the desired output.
Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
Add clock drivers for hi6220 SoC, this driver controls the SoC
registers to supply different clocks to different IPs in the SoC.
We add one divider clock for hi6220 because the divider in hi6220
also has a mask bit but it doesnot obey the rule defined by flag
"CLK_DIVIDER_HIWORD_MASK", we can not get index of the mask bit by
left shift fixed bits (e.g. 16 bits), so we add this divider clock
to handle it.
Signed-off-by: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
Signed-off-by: Bintian Wang <bintian.wang@huawei.com>
Acked-by: Haojian Zhuang <haojian.zhuang@linaro.org>
Reviewed-by: Zhangfei Gao <zhangfei.gao@linaro.org>
Tested-by: Will Deacon <will.deacon@arm.com>
Tested-by: Tyler Baker <tyler.baker@linaro.org>
Tested-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
Having this Kconfig sourced outside the clk menu means the option
is under the "Device Drivers" menu instead of the "Common Clock
Framework" menu. Move it so that the bcm clock config options are
in the right place.
Cc: Alex Elder <elder@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The EMC clock driver uses symbols exported by the EMC driver, so it
needs the corresponding dependency to avoid build breakage.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Some board designers, when running out of clock output pads, decide to
(mis)use PWM output pads to provide a clock to external components.
This driver supports this practice by providing an adapter between the
PWM and clock bindings in the device tree. As the PWM bindings specify
the period in the device tree, this is a fixed clock.
Tested-by: Janusz Uzycki <j.uzycki@elproma.com.pl>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
enhancements and fixes mostly for ARM32, ARM64, MIPS and Power-based
devices. Additionaly the framework core underwent a bit of surgery with
two major changes. The boundary between the clock core and clock
providers (e.g clock drivers) is now more well defined with dedicated
provider helper functions. struct clk no longer maps 1:1 with the
hardware clock but is a true per-user cookie which helps us tracker
users of hardware clocks and debug bad behavior. The second major change
is the addition of rate constraints for clocks. Rate ranges are now
supported which are analogous to the voltage ranges in the regulator
framework. Unfortunately these changes to the core created some
breakeage. We think we fixed it all up but for this reason there are
lots of last minute commits trying to undo the damage.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=zCVK
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus-3.20' of git://git.linaro.org/people/mike.turquette/linux
Pull clock framework updates from Mike Turquette:
"The clock framework changes contain the usual driver additions,
enhancements and fixes mostly for ARM32, ARM64, MIPS and Power-based
devices.
Additionally the framework core underwent a bit of surgery with two
major changes:
- The boundary between the clock core and clock providers (e.g clock
drivers) is now more well defined with dedicated provider helper
functions. struct clk no longer maps 1:1 with the hardware clock
but is a true per-user cookie which helps us tracker users of
hardware clocks and debug bad behavior.
- The addition of rate constraints for clocks. Rate ranges are now
supported which are analogous to the voltage ranges in the
regulator framework.
Unfortunately these changes to the core created some breakeage. We
think we fixed it all up but for this reason there are lots of last
minute commits trying to undo the damage"
* tag 'clk-for-linus-3.20' of git://git.linaro.org/people/mike.turquette/linux: (113 commits)
clk: Only recalculate the rate if needed
Revert "clk: mxs: Fix invalid 32-bit access to frac registers"
clk: qoriq: Add support for the platform PLL
powerpc/corenet: Enable CLK_QORIQ
clk: Replace explicit clk assignment with __clk_hw_set_clk
clk: Add __clk_hw_set_clk helper function
clk: Don't dereference parent clock if is NULL
MIPS: Alchemy: Remove bogus args from alchemy_clk_fgcs_detr
clkdev: Always allocate a struct clk and call __clk_get() w/ CCF
clk: shmobile: div6: Avoid division by zero in .round_rate()
clk: mxs: Fix invalid 32-bit access to frac registers
clk: omap: compile legacy omap3 clocks conditionally
clkdev: Export clk_register_clkdev
clk: Add rate constraints to clocks
clk: remove clk-private.h
pci: xgene: do not use clk-private.h
arm: omap2+ remove dead clock code
clk: Make clk API return per-user struct clk instances
clk: tegra: Define PLLD_DSI and remove dsia(b)_mux
clk: tegra: Add support for the Tegra132 CAR IP block
...
Freescale introduced new ARM-based socs which using the compatible
clock IP block with PowerPC-based socs'. So this driver can be used
on both platforms.
Updated relevant descriptions and renamed this driver to better
represent its meaning and keep the function of driver untouched.
Signed-off-by: Tang Yuantian <Yuantian.Tang@freescale.com>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
The driver allows using CDCE706 in its default configuration recorded in
EEPROM and adjusting of synthesized clocks by consumers.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
SRCU is not necessary to be compiled by default in all cases. For tinification
efforts not compiling SRCU unless necessary is desirable.
The current patch tries to make compiling SRCU optional by introducing a new
Kconfig option CONFIG_SRCU which is selected when any of the components making
use of SRCU are selected.
If we do not select CONFIG_SRCU, srcu.o will not be compiled at all.
text data bss dec hex filename
2007 0 0 2007 7d7 kernel/rcu/srcu.o
Size of arch/powerpc/boot/zImage changes from
text data bss dec hex filename
831552 64180 23944 919676 e087c arch/powerpc/boot/zImage : before
829504 64180 23952 917636 e0084 arch/powerpc/boot/zImage : after
so the savings are about ~2000 bytes.
Signed-off-by: Pranith Kumar <bobby.prani@gmail.com>
CC: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
CC: Josh Triplett <josh@joshtriplett.org>
CC: Lai Jiangshan <laijs@cn.fujitsu.com>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
[ paulmck: resolve conflict due to removal of arch/ia64/kvm/Kconfig. ]
This patch fix company name's spelling typo in module descriptions
and a Kconfig.
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Acked-by: Chris Snook <chris.snook@gmail.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>