We don't maintain it dynamically any longer, so reporting it would
be extremely misleading. Report zero instead.
Signed-off-by: David S. Miller <davem@davemloft.net>
Causes the handler to use the daddr in the ipv4/ipv6 header when
the route gateway is unspecified (local subnet).
Signed-off-by: David S. Miller <davem@davemloft.net>
Soon routes will not have a cached neigh attached, nor will we
be able to necessarily go directly to a neigh from an arbitrary
route.
Signed-off-by: David S. Miller <davem@davemloft.net>
Checking for in_dev being NULL is pointless.
In fact, all of our callers have in_dev precomputed already,
so just pass it in and remove the NULL checking.
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit c074da2810.
This change has several unwanted side effects:
1) Sockets will cache the DST_NOCACHE route in sk->sk_rx_dst and we'll
thus never create a real cached route.
2) All TCP traffic will use DST_NOCACHE and never use the routing
cache at all.
Signed-off-by: David S. Miller <davem@davemloft.net>
DDOS synflood attacks hit badly IP route cache.
On typical machines, this cache is allowed to hold up to 8 Millions dst
entries, 256 bytes for each, for a total of 2GB of memory.
rt_garbage_collect() triggers and tries to cleanup things.
Eventually route cache is disabled but machine is under fire and might
OOM and crash.
This patch exploits the new TCP early demux, to set a nocache
boolean in case incoming TCP frame is for a not yet ESTABLISHED or
TIMEWAIT socket.
This 'nocache' boolean is then used in case dst entry is not found in
route cache, to create an unhashed dst entry (DST_NOCACHE)
SYN-cookie-ACK sent use a similar mechanism (ipv4: tcp: dont cache
output dst for syncookies), so after this patch, a machine is able to
absorb a DDOS synflood attack without polluting its IP route cache.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Hans Schillstrom <hans.schillstrom@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
And account for the fact that, when we are not forwarding, we should
bump statistic counters rather than emit an ICMP response.
RP-filter rejected lookups are still not cached.
Since -EHOSTUNREACH and -ENETUNREACH can now no longer be seen in
ip_rcv_finish(), remove those checks.
Signed-off-by: David S. Miller <davem@davemloft.net>
IPv4 routing cache entries no longer use dst->expires, because the
metrics, PMTU, and redirect information are stored in the inetpeer
cache.
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't cache output dst for syncookies, as this adds pressure on IP route
cache and rcu subsystem for no gain.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Hans Schillstrom <hans.schillstrom@ericsson.com>
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It makes no sense to execute this limit test every time we create a
routing cache entry.
We can't simply error out on these things since we've silently
accepted and truncated them forever.
Signed-off-by: David S. Miller <davem@davemloft.net>
With ip_rt_frag_needed() removed, we have to explicitly update PMTU
information in every ICMP error handler.
Create two helper functions to facilitate this.
1) ipv4_sk_update_pmtu()
This updates the PMTU when we have a socket context to
work with.
2) ipv4_update_pmtu()
Raw version, used when no socket context is available. For this
interface, we essentially just pass in explicit arguments for
the flow identity information we would have extracted from the
socket.
And you'll notice that ipv4_sk_update_pmtu() is simply implemented
in terms of ipv4_update_pmtu()
Note that __ip_route_output_key() is used, rather than something like
ip_route_output_flow() or ip_route_output_key(). This is because we
absolutely do not want to end up with a route that does IPSEC
encapsulation and the like. Instead, we only want the route that
would get us to the node described by the outermost IP header.
Reported-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Routing of 127/8 is tradtionally forbidden, we consider
packets from that address block martian when routing and do
not process corresponding ARP requests.
This is a sane default but renders a huge address space
practically unuseable.
The RFC states that no address within the 127/8 block should
ever appear on any network anywhere but it does not forbid
the use of such addresses outside of the loopback device in
particular. For example to address a pool of virtual guests
behind a load balancer.
This patch adds a new interface option 'route_localnet'
enabling routing of the 127/8 address block and processing
of ARP requests on a specific interface.
Note that for the feature to work, the default local route
covering 127/8 dev lo needs to be removed.
Example:
$ sysctl -w net.ipv4.conf.eth0.route_localnet=1
$ ip route del 127.0.0.0/8 dev lo table local
$ ip addr add 127.1.0.1/16 dev eth0
$ ip route flush cache
V2: Fix invalid check to auto flush cache (thanks davem)
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We handle NULL in rt{,6}_set_peer but then our caller will try to pass
that NULL pointer into inet_putpeer() which isn't ready for it.
Fix this by moving the NULL check one level up, and then remove the
now unnecessary NULL check from inetpeer_ptr_set_peer().
Reported-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This implementation can deal with having many inetpeer roots, which is
a necessary prerequisite for per-FIB table rooted peer tables.
Each family (AF_INET, AF_INET6) has a sequence number which we bump
when we get a family invalidation request.
Each peer lookup cheaply checks whether the flush sequence of the
root we are using is out of date, and if so flushes it and updates
the sequence number.
Signed-off-by: David S. Miller <davem@davemloft.net>
There is zero point to this function.
It's only real substance is to perform an extremely outdated BSD4.2
ICMP check, which we can safely remove. If you really have a MTU
limited link being routed by a BSD4.2 derived system, here's a nickel
go buy yourself a real router.
The other actions of ip_rt_frag_needed(), checking and conditionally
updating the peer, are done by the per-protocol handlers of the ICMP
event.
TCP, UDP, et al. have a handler which will receive this event and
transmit it back into the associated route via dst_ops->update_pmtu().
This simplification is important, because it eliminates the one place
where we do not have a proper route context in which to make an
inetpeer lookup.
Signed-off-by: David S. Miller <davem@davemloft.net>
We encode the pointer(s) into an unsigned long with one state bit.
The state bit is used so we can store the inetpeer tree root to use
when resolving the peer later.
Later the peer roots will be per-FIB table, and this change works to
facilitate that.
Signed-off-by: David S. Miller <davem@davemloft.net>
We only need one interface for this operation, since we always know
which inetpeer root we want to flush.
Signed-off-by: David S. Miller <davem@davemloft.net>
There's a lot of places that open-code rt{,6}_get_peer() only because
they want to set 'create' to one. So add an rt{,6}_get_peer_create()
for their sake.
There were also a few spots open-coding plain rt{,6}_get_peer() and
those are transformed here as well.
Signed-off-by: David S. Miller <davem@davemloft.net>
add struct net as a parameter of inet_getpeer_v[4,6],
use net to replace &init_net.
and modify some places to provide net for inet_getpeer_v[4,6]
Signed-off-by: Gao feng <gaofeng@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
now inetpeer doesn't support namespace,the information will
be leaking across namespace.
this patch move the global vars v4_peers and v6_peers to
netns_ipv4 and netns_ipv6 as a field peers.
add struct pernet_operations inetpeer_ops to initial pernet
inetpeer data.
and change family_to_base and inet_getpeer to support namespace.
Signed-off-by: Gao feng <gaofeng@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
UDP stack needs a minimum hash size value for proper operation and also
uses alloc_large_system_hash() for proper NUMA distribution of its hash
tables and automatic sizing depending on available system memory.
On some low memory situations, udp_table_init() must ignore the
alloc_large_system_hash() result and reallocs a bigger memory area.
As we cannot easily free old hash table, we leak it and kmemleak can
issue a warning.
This patch adds a low limit parameter to alloc_large_system_hash() to
solve this problem.
We then specify UDP_HTABLE_SIZE_MIN for UDP/UDPLite hash table
allocation.
Reported-by: Mark Asselstine <mark.asselstine@windriver.com>
Reported-by: Tim Bird <tim.bird@am.sony.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace simple_strtoul with kstrtoul in three similar occurrences, all setup
handlers:
* route.c: set_rhash_entries
* tcp.c: set_thash_entries
* udp.c: set_uhash_entries
Also check if the conversion failed.
Signed-off-by: Eldad Zack <eldad@fogrefinery.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the current debugging style and enable dynamic_debug.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Standardize the net core ratelimited logging functions.
Coalesce formats, align arguments.
Change a printk then vprintk sequence to use printf extension %pV.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This results in code with less boiler plate that is a bit easier
to read.
Additionally stops us from using compatibility code in the sysctl
core, hastening the day when the compatibility code can be removed.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Acked-by: Pavel Emelyanov <xemul@parallels.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
sysctl no longer requires explicit creation of directories. The neigh
directory is always populated with at least a default entry so this
won't cause any user visible changes.
Delete the ipv4_path and the ipv4_skeleton these are no longer needed.
Directly register the ipv4_route_table.
And since I am an idiot remove the header definitions that I should
have removed in the previous patch.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Acked-by: Pavel Emelyanov <xemul@parallels.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This makes it clearer which sysctls are relative to your current network
namespace.
This makes it a little less error prone by not exposing sysctls for the
initial network namespace in other namespaces.
This is the same way we handle all of our other network interfaces to
userspace and I can't honestly remember why we didn't do this for
sysctls right from the start.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Acked-by: Pavel Emelyanov <xemul@parallels.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
net/core/sysctl_net_core.c: In function ‘sysctl_core_init’:
net/core/sysctl_net_core.c:259: error: implicit declaration of function ‘kmemleak_not_leak’
with same error in net/ipv4/route.c
Signed-off-by: Shan Wei <davidshan@tencent.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use of "unsigned int" is preferred to bare "unsigned" in net tree.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix checkpatch errors of the following type:
* ERROR: "foo * bar" should be "foo *bar"
* ERROR: "(foo*)" should be "(foo *)"
Signed-off-by: Daniel Baluta <dbaluta@ixiacom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Need to export this to enable drivers use rt_tos2priority()
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) Provide device string properly for USB i2400m wimax devices, also
don't OOPS when providing firmware string. From Phil Sutter.
2) Add support for sh_eth SH7734 chips, from Nobuhiro Iwamatsu.
3) Add another device ID to USB zaurus driver, from Guan Xin.
4) Loop index start in pool vector iterator is wrong causing MAC to not
get configured in bnx2x driver, fix from Dmitry Kravkov.
5) EQL driver assumes HZ=100, fix from Eric Dumazet.
6) Now that skb_add_rx_frag() can specify the truesize increment
separately, do so in f_phonet and cdc_phonet, also from Eric
Dumazet.
7) virtio_net accidently uses net_ratelimit() not only on the kernel
warning but also the statistic bump, fix from Rick Jones.
8) ip_route_input_mc() uses fixed init_net namespace, oops, use
dev_net(dev) instead. Fix from Benjamin LaHaise.
9) dev_forward_skb() needs to clear the incoming interface index of the
SKB so that it looks like a new incoming packet, also from Benjamin
LaHaise.
10) iwlwifi mistakenly initializes a channel entry as 2GHZ instead of
5GHZ, fix from Stanislav Yakovlev.
11) Missing kmalloc() return value checks in orinoco, from Santosh
Nayak.
12) ath9k doesn't check for HT capabilities in the right way, it is
checking ht_supported instead of the ATH9K_HW_CAP_HT flag. Fix from
Sujith Manoharan.
13) Fix x86 BPF JIT emission of 16-bit immediate field of AND
instructions, from Feiran Zhuang.
14) Avoid infinite loop in GARP code when registering sysfs entries.
From David Ward.
15) rose protocol uses memcpy instead of memcmp in a device address
comparison, oops. Fix from Daniel Borkmann.
16) Fix build of lpc_eth due to dev_hw_addr_rancom() interface being
renamed to eth_hw_addr_random(). From Roland Stigge.
17) Make ipv6 RTM_GETROUTE interpret RTA_IIF attribute the same way
that ipv4 does. Fix from Shmulik Ladkani.
18) via-rhine has an inverted bit test, causing suspend/resume
regressions. Fix from Andreas Mohr.
19) RIONET assumes 4K page size, fix from Akinobu Mita.
20) Initialization of imask register in sky2 is buggy, because bits are
"or'd" into an uninitialized local variable. Fix from Lino
Sanfilippo.
21) Fix FCOE checksum offload handling, from Yi Zou.
22) Fix VLAN processing regression in e1000, from Jiri Pirko.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (52 commits)
sky2: dont overwrite settings for PHY Quick link
tg3: Fix 5717 serdes powerdown problem
net: usb: cdc_eem: fix mtu
net: sh_eth: fix endian check for architecture independent
usb/rtl8150 : Remove duplicated definitions
rionet: fix page allocation order of rionet_active
via-rhine: fix wait-bit inversion.
ipv6: Fix RTM_GETROUTE's interpretation of RTA_IIF to be consistent with ipv4
net: lpc_eth: Fix rename of dev_hw_addr_random
net/netfilter/nfnetlink_acct.c: use linux/atomic.h
rose_dev: fix memcpy-bug in rose_set_mac_address
Fix non TBI PHY access; a bad merge undid bug fix in a previous commit.
net/garp: avoid infinite loop if attribute already exists
x86 bpf_jit: fix a bug in emitting the 16-bit immediate operand of AND
bonding: emit event when bonding changes MAC
mac80211: fix oper channel timestamp updation
ath9k: Use HW HT capabilites properly
MAINTAINERS: adding maintainer for ipw2x00
net: orinoco: add error handling for failed kmalloc().
net/wireless: ipw2x00: fix a typo in wiphy struct initilization
...
These macros contain a hidden goto, and are thus extremely error
prone and make code hard to audit.
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove all #inclusions of asm/system.h preparatory to splitting and killing
it. Performed with the following command:
perl -p -i -e 's!^#\s*include\s*<asm/system[.]h>.*\n!!' `grep -Irl '^#\s*include\s*<asm/system[.]h>' *`
Signed-off-by: David Howells <dhowells@redhat.com>
When using multicast over a local bridge feeding a number of LXC guests
using veth, the LXC guests are unable to get a response from other guests
when pinging 224.0.0.1. Multicast packets did not appear to be getting
delivered to the network namespaces of the guest hosts, and further
inspection showed that the incoming route was pointing to the loopback
device of the host, not the guest. This lead to the wrong network namespace
being picked up by sockets (like ICMP). Fix this by using the correct
network namespace when creating the inbound route entry.
Signed-off-by: Benjamin LaHaise <bcrl@kvack.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add #define pr_fmt(fmt) as appropriate.
Add "IPv4: ", "TCP: ", and "IPsec: " to appropriate files.
Standardize on "UDPLite: " for appropriate uses.
Some prefixes were previously "UDPLITE: " and "UDP-Lite: ".
Add KBUILD_MODNAME ": " to icmp and gre.
Remove embedded prefixes as appropriate.
Add missing "\n" to pr_info in gre.c.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use a more current kernel messaging style.
Convert a printk block to print_hex_dump.
Coalesce formats, align arguments.
Use %s, __func__ instead of embedding function names.
Some messages that were prefixed with <foo>_close are
now prefixed with <foo>_fini. Some ah4 and esp messages
are now not prefixed with "ip ".
The intent of this patch is to later add something like
#define pr_fmt(fmt) "IPv4: " fmt.
to standardize the output messages.
Text size is trivially reduced. (x86-32 allyesconfig)
$ size net/ipv4/built-in.o*
text data bss dec hex filename
887888 31558 249696 1169142 11d6f6 net/ipv4/built-in.o.new
887934 31558 249800 1169292 11d78c net/ipv4/built-in.o.old
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As we invalidate the inetpeer tree along with the routing cache now,
we don't need a genid to reset the redirect handling when the routing
cache is flushed.
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We initialize the routing metrics with the values cached on the
inetpeer in rt_init_metrics(). So if we have the metrics cached on the
inetpeer, we ignore the user configured fib_metrics.
To fix this issue, we replace the old tree with a fresh initialized
inet_peer_base. The old tree is removed later with a delayed work queue.
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the future the ipv4/ipv6 route gateway will take on two types
of values:
1) INADDR_ANY/IN6ADDR_ANY, for local network routes, and in this case
the neighbour must be obtained using the destination address in
ipv4/ipv6 header as the lookup key.
2) Everything else, the actual nexthop route address.
So if the gateway is not inaddr-any we use it, otherwise we must use
the packet's destination address.
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
net/bluetooth/l2cap_core.c
Just two overlapping changes, one added an initialization of
a local variable, and another change added a new local variable.
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: David Miller <davem@davemloft.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit 2c8cec5c10 (ipv4: Cache learned PMTU information in inetpeer)
removed IP route cache garbage collector a bit too soon, as this gc was
responsible for expired routes cleanup, releasing their neighbour
reference.
As pointed out by Robert Gladewitz, recent kernels can fill and exhaust
their neighbour cache.
Reintroduce the garbage collection, since we'll have to wait our
neighbour lookups become refcount-less to not depend on this stuff.
Reported-by: Robert Gladewitz <gladewitz@gmx.de>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To reflect the fact that a refrence is not obtained to the
resulting neighbour entry.
Signed-off-by: David S. Miller <davem@davemloft.net>
Acked-by: Roland Dreier <roland@purestorage.com>
If ipv4_valdiate_peer() fails during a cached entry lookup,
we'll NULL derer since the loop iterator assumes rth is not
NULL.
Letting this be handled as a failure is just bogus, so just make it
not fail. If we have trouble getting a non-NULL neighbour for the
redirected gateway, just restore the original gateway and continue.
The very next use of this cached route will try again.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
__mkroute_output fails to work with the original tos
and uses value with stripped RTO_ONLINK bit. Make sure we put
the original TOS bits into rt_key_tos because it used to match
cached route.
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: David S. Miller <davem@davemloft.net>
Otherwise we won't notice the peer GENID change.
Reported-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of instantiating an entire new neigh_table instance
just for ATM handling, use the neigh device private facility.
Signed-off-by: David S. Miller <davem@davemloft.net>
After commit f2c31e32b3 (fix NULL dereferences in check_peer_redir()),
dst_get_neighbour() should be guarded by rcu_read_lock() /
rcu_read_unlock() section.
Reported-by: Miles Lane <miles.lane@gmail.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now inetpeer is the place where we cache redirect information for ipv4
destinations, we must be able to invalidate informations when a route is
added/removed on host.
As inetpeer is not yet namespace aware, this patch adds a shared
redirect_genid, and a per inetpeer redirect_genid. This might be changed
later if inetpeer becomes ns aware.
Cache information for one inerpeer is valid as long as its
redirect_genid has the same value than global redirect_genid.
Reported-by: Arkadiusz Miśkiewicz <a.miskiewicz@gmail.com>
Tested-by: Arkadiusz Miśkiewicz <a.miskiewicz@gmail.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The pmtu informations on the inetpeer are visible for output and
input routes. On packet forwarding, we might propagate a learned
pmtu to the sender. As we update the pmtu informations of the
inetpeer on demand, the original sender of the forwarded packets
might never notice when the pmtu to that inetpeer increases.
So use the mtu of the outgoing device on packet forwarding instead
of the pmtu to the final destination.
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We move all mtu handling from dst_mtu() down to the protocol
layer. So each protocol can implement the mtu handling in
a different manner.
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We plan to invoke the dst_opt->default_mtu() method unconditioally
from dst_mtu(). So rename the method to dst_opt->mtu() to match
the name with the new meaning.
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As it is, we return null as the default mtu of blackhole routes.
This may lead to a propagation of a bogus pmtu if the default_mtu
method of a blackhole route is invoked. So return dst->dev->mtu
as the default mtu instead.
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit f39925dbde (ipv4: Cache learned redirect information in
inetpeer.) introduced a regression in ICMP redirect handling.
It assumed ipv4_dst_check() would be called because all possible routes
were attached to the inetpeer we modify in ip_rt_redirect(), but thats
not true.
commit 7cc9150ebe (route: fix ICMP redirect validation) tried to fix
this but solution was not complete. (It fixed only one route)
So we must lookup existing routes (including different TOS values) and
call check_peer_redir() on them.
Reported-by: Ivan Zahariev <famzah@icdsoft.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
CC: Flavio Leitner <fbl@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As we update the learned pmtu informations on demand, we might
report a nagative expiration time value to userspace if the
pmtu informations are already expired and we have not send a
packet to that inetpeer after expiration. With this patch we
send a expire time of null to userspace after expiration
until the next packet is send to that inetpeer.
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In func ipv4_dst_check,check_peer_pmtu should be called only when peer is updated.
So,if the peer is not updated in ip_rt_frag_needed,we can not inc __rt_peer_genid.
Signed-off-by: Gao feng <gaofeng@cn.fujitsu.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The commit f39925dbde
(ipv4: Cache learned redirect information in inetpeer.)
removed some ICMP packet validations which are required by
RFC 1122, section 3.2.2.2:
...
A Redirect message SHOULD be silently discarded if the new
gateway address it specifies is not on the same connected
(sub-) net through which the Redirect arrived [INTRO:2,
Appendix A], or if the source of the Redirect is not the
current first-hop gateway for the specified destination (see
Section 3.3.1).
Signed-off-by: Flavio Leitner <fbl@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
removing obsoleted sysctl,
ip_rt_gc_interval variable no longer used since 2.6.38
Signed-off-by: Vasily Averin <vvs@sw.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
RCU api had been completed and rcu_access_pointer() or
rcu_dereference_protected() are better than generic
rcu_dereference_raw()
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As rt_iif represents input device even for packets
coming from loopback with output route, it is not an unique
key specific to input routes. Now rt_route_iif has such role,
it was fl.iif in 2.6.38, so better to change the checks at
some places to save CPU cycles and to restore 2.6.38 semantics.
compare_keys:
- input routes: only rt_route_iif matters, rt_iif is same
- output routes: only rt_oif matters, rt_iif is not
used for matching in __ip_route_output_key
- now we are back to 2.6.38 state
ip_route_input_common:
- matching rt_route_iif implies input route
- compared to 2.6.38 we eliminated one rth->fl.oif check
because it was not needed even for 2.6.38
compare_hash_inputs:
Only the change here is not an optimization, it has
effect only for output routes. I assume I'm restoring
the original intention to ignore oif, it was using fl.iif
- now we are back to 2.6.38 state
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: David S. Miller <davem@davemloft.net>
compare_keys and ip_route_input_common rely on
rt_oif for distinguishing of input and output routes
with same keys values. But sometimes the input route has
also same hash chain (keyed by iif != 0) with the output
routes (keyed by orig_oif=0). Problem visible if running
with small number of rhash_entries.
Fix them to use rt_route_iif instead. By this way
input route can not be returned to users that request
output route.
The patch fixes the ip_rt_bug errors that were
reported in ip_local_out context, mostly for 255.255.255.255
destinations.
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: David S. Miller <davem@davemloft.net>
Computers have become a lot faster since we compromised on the
partial MD4 hash which we use currently for performance reasons.
MD5 is a much safer choice, and is inline with both RFC1948 and
other ISS generators (OpenBSD, Solaris, etc.)
Furthermore, only having 24-bits of the sequence number be truly
unpredictable is a very serious limitation. So the periodic
regeneration and 8-bit counter have been removed. We compute and
use a full 32-bit sequence number.
For ipv6, DCCP was found to use a 32-bit truncated initial sequence
number (it needs 43-bits) and that is fixed here as well.
Reported-by: Dan Kaminsky <dan@doxpara.com>
Tested-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: David S. Miller <davem@davemloft.net>
Gergely Kalman reported crashes in check_peer_redir().
It appears commit f39925dbde (ipv4: Cache learned redirect
information in inetpeer.) added a race, leading to possible NULL ptr
dereference.
Since we can now change dst neighbour, we should make sure a reader can
safely use a neighbour.
Add RCU protection to dst neighbour, and make sure check_peer_redir()
can be called safely by different cpus in parallel.
As neighbours are already freed after one RCU grace period, this patch
should not add typical RCU penalty (cache cold effects)
Many thanks to Gergely for providing a pretty report pointing to the
bug.
Reported-by: Gergely Kalman <synapse@hippy.csoma.elte.hu>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
rt_tos was changed to iph->tos but it must be filtered by RT_TOS
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the future dst entries will be neigh-less. In that environment we
need to have an easy transition point for current users of
dst->neighbour outside of the packet output fast path.
Signed-off-by: David S. Miller <davem@davemloft.net>
It's just taking on one of two possible values, either
neigh_ops->output or dev_queue_xmit(). And this is purely depending
upon whether nud_state has NUD_CONNECTED set or not.
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that there is a one-to-one correspondance between neighbour
and hh_cache entries, we no longer need:
1) dynamic allocation
2) attachment to dst->hh
3) refcounting
Initialization of the hh_cache entry is indicated by hh_len
being non-zero, and such initialization is always done with
the neighbour's lock held as a writer.
Signed-off-by: David S. Miller <davem@davemloft.net>
Get rid of all of the useless and costly indirection
by doing the neigh hash table lookup directly inside
of the neighbour binding.
Rename from arp_bind_neighbour to rt_bind_neighbour.
Use new helpers {__,}ipv4_neigh_lookup()
In rt_bind_neighbour() get rid of useless tests which
are never true in the context this function is called,
namely dev is never NULL and the dst->neighbour is
always NULL.
Signed-off-by: David S. Miller <davem@davemloft.net>
Make the case labels the same indent as the switch.
git diff -w shows no difference.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Knut Tidemann found that first packet of a multicast flow was not
correctly received, and bisected the regression to commit b23dd4fe42
(Make output route lookup return rtable directly.)
Special thanks to Knut, who provided a very nice bug report, including
sample programs to demonstrate the bug.
Reported-and-bisectedby: Knut Tidemann <knut.andre.tidemann@jotron.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The message size allocated for rtnl ifinfo dumps was limited to
a single page. This is not enough for additional interface info
available with devices that support SR-IOV and caused a bug in
which VF info would not be displayed if more than approximately
40 VFs were created per interface.
Implement a new function pointer for the rtnl_register service that will
calculate the amount of data required for the ifinfo dump and allocate
enough data to satisfy the request.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
commit 2c8cec5c10 (ipv4: Cache learned PMTU information in inetpeer)
added some racy peer->pmtu_expires accesses.
As its value can be changed by another cpu/thread, we should be more
careful, reading its value once.
Add peer_pmtu_expired() and peer_pmtu_cleaned() helpers
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a stack backtrace to the ip_rt_bug path for debugging
Signed-off-by: Dave Jones <davej@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's way past it's usefulness. And this gets rid of a bunch
of stray ->rt_{dst,src} references.
Even the comment documenting the macro was inaccurate (stated
default was 1 when it's 0).
If reintroduced, it should be done properly, with dynamic debug
facilities.
Signed-off-by: David S. Miller <davem@davemloft.net>
Pass in the sk_buff so that we can fetch the necessary keys from
the packet header when working with input routes.
Signed-off-by: David S. Miller <davem@davemloft.net>
To more accurately reflect that it is purely a routing
cache lookup key and is used in no other context.
Signed-off-by: David S. Miller <davem@davemloft.net>
Slow path output route resolution always makes sure that
->{saddr,daddr} are set, and also if we trigger into IPSEC resolution
we initialize them as well, because xfrm_lookup() expects them to be
fully resolved.
But if we hit the fast path and flowi4->flowi4_proto is zero, we won't
do this initialization.
Therefore, move the IPSEC path initialization to the route cache
lookup fast path to make sure these are always set.
Signed-off-by: David S. Miller <davem@davemloft.net>
Make dst_alloc() and it's users explicitly initialize the entire
entry.
The zero'ing done by kmem_cache_zalloc() was almost entirely
redundant.
Signed-off-by: David S. Miller <davem@davemloft.net>
Resolved logic conflicts causing a build failure due to
drivers/net/r8169.c changes using a patch from Stephen Rothwell.
Signed-off-by: David S. Miller <davem@davemloft.net>
Add const qualifiers to structs iphdr, ipv6hdr and in6_addr pointers
where possible, to make code intention more obvious.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
fib_select_default() is a complete NOP, and completely pointless
to invoke, when we have no more than 1 default route installed.
And this is far and away the common case.
So remember how many prefixlen==0 routes we have in the routing
table, and elide the call when we have no more than one of those.
This cuts output route creation time by 157 cycles on Niagara2+.
In order to add the new int to fib_table, we have to correct the type
of ->tb_data[] to unsigned long, otherwise the private area will be
unaligned on 64-bit systems.
Signed-off-by: David S. Miller <davem@davemloft.net>
Reviewed-by: Eric Dumazet <eric.dumazet@gmail.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (34 commits)
net: Add support for SMSC LAN9530, LAN9730 and LAN89530
mlx4_en: Restoring RX buffer pointer in case of failure
mlx4: Sensing link type at device initialization
ipv4: Fix "Set rt->rt_iif more sanely on output routes."
MAINTAINERS: add entry for Xen network backend
be2net: Fix suspend/resume operation
be2net: Rename some struct members for clarity
pppoe: drop PPPOX_ZOMBIEs in pppoe_flush_dev
dsa/mv88e6131: add support for mv88e6085 switch
ipv6: Enable RFS sk_rxhash tracking for ipv6 sockets (v2)
be2net: Fix a potential crash during shutdown.
bna: Fix for handling firmware heartbeat failure
can: mcp251x: Allow pass IRQ flags through platform data.
smsc911x: fix mac_lock acquision before calling smsc911x_mac_read
iwlwifi: accept EEPROM version 0x423 for iwl6000
rt2x00: fix cancelling uninitialized work
rtlwifi: Fix some warnings/bugs
p54usb: IDs for two new devices
wl12xx: fix potential buffer overflow in testmode nvs push
zd1211rw: reset rx idle timer from tasklet
...
This makes sk_buff available for other use in fib_validate_source().
Signed-off-by: Michael Smith <msmith@cbnco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 1018b5c016 ("Set rt->rt_iif more
sanely on output routes.") breaks rt_is_{output,input}_route.
This became the cause to return "IP_PKTINFO's ->ipi_ifindex == 0".
To fix it, this does:
1) Add "int rt_route_iif;" to struct rtable
2) For input routes, always set rt_route_iif to same value as rt_iif
3) For output routes, always set rt_route_iif to zero. Set rt_iif
as it is done currently.
4) Change rt_is_{output,input}_route() to test rt_route_iif
Signed-off-by: OGAWA Hirofumi <hirofumi@mail.parknet.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
Any operation that:
1) Brings up an interface
2) Adds an IP address to an interface
3) Deletes an IP address from an interface
can potentially invalidate the nh_saddr value, requiring
it to be recomputed.
Perform the recomputation lazily using a generation ID.
Reported-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 2c8cec5c10 (Cache learned PMTU information in inetpeer) added
an extra inet_putpeer() call in ip_rt_update_pmtu().
This results in various problems, since we can free one inetpeer, while
it is still in use.
Ref: http://www.spinics.net/lists/netdev/msg159121.html
Reported-by: Alexander Beregalov <a.beregalov@gmail.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ECN support incorrectly maps ECN BESTEFFORT packets to TC_PRIO_FILLER
(1) instead of TC_PRIO_BESTEFFORT (0)
This means ECN enabled flows are placed in pfifo_fast/prio low priority
band, giving ECN enabled flows [ECT(0) and CE codepoints] higher drop
probabilities.
This is rather unfortunate, given we would like ECN being more widely
used.
Ref : http://www.coverfire.com/archives/2011/03/13/pfifo_fast-and-ecn/
Signed-off-by: Dan Siemon <dan@coverfire.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Dave Täht <d@taht.net>
Cc: Jonathan Morton <chromatix99@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On current net-next-2.6, when Linux receives ICMP Type: 3, Code: 4
(Destination unreachable (Fragmentation needed)),
icmp_unreach
-> ip_rt_frag_needed
(peer->pmtu_expires is set here)
-> tcp_v4_err
-> do_pmtu_discovery
-> ip_rt_update_pmtu
(peer->pmtu_expires is already set,
so check_peer_pmtu is skipped.)
-> check_peer_pmtu
check_peer_pmtu is skipped and MTU is not updated.
To fix this, let check_peer_pmtu execute unconditionally.
And some minor fixes
1) Avoid potential peer->pmtu_expires set to be zero.
2) In check_peer_pmtu, argument of time_before is reversed.
3) check_peer_pmtu expects peer->pmtu_orig is initialized as zero,
but not initialized.
Signed-off-by: Hiroaki SHIMODA <shimoda.hiroaki@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To start doing these conversions, we need to add some temporary
flow4_* macros which will eventually go away when all the protocol
code paths are changed to work on AF specific flowi objects.
Signed-off-by: David S. Miller <davem@davemloft.net>
I intend to turn struct flowi into a union of AF specific flowi
structs. There will be a common structure that each variant includes
first, much like struct sock_common.
This is the first step to move in that direction.
Signed-off-by: David S. Miller <davem@davemloft.net>
All callers are under rcu_read_lock() protection already.
Rename to ip_check_mc_rcu() to make it even more clear.
Signed-off-by: David S. Miller <davem@davemloft.net>
Like in commit 44713b67db
("ipv4: Optimize flow initialization in output route lookup."
we can optimize the on-stack flow setup to only initialize
the members which are actually used.
Otherwise we bzero the entire structure, then initialize
explicitly the first half of it.
Signed-off-by: David S. Miller <davem@davemloft.net>
The only necessary parts are the src/dst addresses, the
interface indexes, the TOS, and the mark.
The rest is unnecessary bloat, which amounts to nearly
50 bytes on 64-bit.
Signed-off-by: David S. Miller <davem@davemloft.net>
rt->rt_iif is only ever inspected on input routes, for example DCCP
uses this to populate a route lookup flow key when generating replies
to another packet.
Therefore, setting it to anything other than zero on output routes
makes no sense.
Signed-off-by: David S. Miller <davem@davemloft.net>
We burn a lot of useless cycles, cpu store buffer traffic, and
memory operations memset()'ing the on-stack flow used to perform
output route lookups in __ip_route_output_key().
Only the first half of the flow object members even matter for
output route lookups in this context, specifically:
FIB rules matching cares about:
dst, src, tos, iif, oif, mark
FIB trie lookup cares about:
dst
FIB semantic match cares about:
tos, scope, oif
Therefore only initialize these specific members and elide the
memset entirely.
On Niagara2 this kills about ~300 cycles from the output route
lookup path.
Likely, we can take things further, since all callers of output
route lookups essentially throw away the on-stack flow they use.
So they don't care if we use it as a scratch-pad to compute the
final flow key.
Signed-off-by: David S. Miller <davem@davemloft.net>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Commit 0dbaee3b37 (net: Abstract default ADVMSS behind an
accessor.) introduced a possible crash in tcp_connect_init(), when
dst->default_advmss() is called from dst_metric_advmss()
Reported-by: George Spelvin <linux@horizon.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The only troublesome bit here is __mkroute_output which wants
to override res->fi and res->type, compute those in local
variables instead.
Signed-off-by: David S. Miller <davem@davemloft.net>
This allows avoiding multiple writes to the initial __refcnt.
The most simplest cases of wanting an initial reference of "1"
in ipv4 and ipv6 have been converted, the rest have been left
along and kept at the existing "0".
Signed-off-by: David S. Miller <davem@davemloft.net>
This also allows us to combine all the dst->flags settings and avoid
read/modify/write sequences to this struct member.
Signed-off-by: David S. Miller <davem@davemloft.net>
There's a lot of redundancy and unnecessary stack frames
in the output route creation path.
1) Make __mkroute_output() return error pointers.
2) Eliminate ip_mkroute_output() entirely, made possible by #1.
3) Call __mkroute_output() directly and handling the returning error
pointers in ip_route_output_slow().
Signed-off-by: David S. Miller <davem@davemloft.net>
Note that we do not generate the redirect netevent any longer,
because we don't create a new cached route.
Instead, once the new neighbour is bound to the cached route,
we emit a neigh update event instead.
Signed-off-by: David S. Miller <davem@davemloft.net>
The general idea is that if we learn new PMTU information, we
bump the peer genid.
This triggers the dst_ops->check() code to validate and if
necessary propagate the new PMTU value into the metrics.
Learned PMTU information self-expires.
This means that it is not necessary to kill a cached route
entry just because the PMTU information is too old.
As a consequence:
1) When the path appears unreachable (dst_ops->link_failure
or dst_ops->negative_advice) we unwind the PMTU state if
it is out of date, instead of killing the cached route.
A redirected route will still be invalidated in these
situations.
2) rt_check_expire(), rt_worker_func(), et al. are no longer
necessary at all.
Signed-off-by: David S. Miller <davem@davemloft.net>
If we didn't have a routing cache, we would not be able to properly
propagate certain kinds of dynamic path attributes, for example
PMTU information and redirects.
The reason is that if we didn't have a routing cache, then there would
be no way to lookup all of the active cached routes hanging off of
sockets, tunnels, IPSEC bundles, etc.
Consider the case where we created a cached route, but no inetpeer
entry existed and also we were not asked to pre-COW the route metrics
and therefore did not force the creation a new inetpeer entry.
If we later get a PMTU message, or a redirect, and store this
information in a new inetpeer entry, there is no way to teach that
cached route about the newly existing inetpeer entry.
The facilities implemented here handle this problem.
First we create a generation ID. When we create a cached route of any
kind, we remember the generation ID at the time of attachment. Any
time we force-create an inetpeer entry in response to new path
information, we bump that generation ID.
The dst_ops->check() callback is where the knowledge of this event
is propagated. If the global generation ID does not equal the one
stored in the cached route, and the cached route has not attached
to an inetpeer yet, we look it up and attach if one is found. Now
that we've updated the cached route's information, we update the
route's generation ID too.
This clears the way for implementing PMTU and redirects directly in
the inetpeer cache. There is absolutely no need to consult cached
route information in order to maintain this information.
At this point nothing bumps the inetpeer genids, that comes in the
later changes which handle PMTUs and redirects using inetpeers.
Signed-off-by: David S. Miller <davem@davemloft.net>
Like metrics, the ICMP rate limiting bits are cached state about
a destination. So move it into the inet_peer entries.
If an inet_peer cannot be bound (the reason is memory allocation
failure or similar), the policy is to allow.
Signed-off-by: David S. Miller <davem@davemloft.net>
Always lookup to see if we have an existing inetpeer entry for
a route. Let FLOWI_FLAG_PRECOW_METRICS merely influence the
"create" argument to rt_bind_peer().
Also, call rt_bind_peer() unconditionally since it is not
possible for rt->peer to be non-NULL at this point.
Signed-off-by: David S. Miller <davem@davemloft.net>
Both fib_trie and fib_hash have a local implementation of
fib_table_select_default(). This is completely unnecessary
code duplication.
Since we now remember the fib_table and the head of the fib
alias list of the default route, we can implement one single
generic version of this routine.
Looking at the fib_hash implementation you may get the impression
that it's possible for there to be multiple top-level routes in
the table for the default route. The truth is, it isn't, the
insert code will only allow one entry to exist in the zero
prefix hash table, because all keys evaluate to zero and all
keys in a hash table must be unique.
Signed-off-by: David S. Miller <davem@davemloft.net>
When an IPSEC SA is still being set up, __xfrm_lookup() will return
-EREMOTE and so ip_route_output_flow() will return a blackhole route.
This can happen in a sndmsg call, and after d33e455337 ("net: Abstract
default MTU metric calculation behind an accessor.") this leads to a
crash in ip_append_data() because the blackhole dst_ops have no
default_mtu() method and so dst_mtu() calls a NULL pointer.
Fix this by adding default_mtu() methods (that simply return 0, matching
the old behavior) to the blackhole dst_ops.
The IPv4 part of this patch fixes a crash that I saw when using an IPSEC
VPN; the IPv6 part is untested because I don't have an IPv6 VPN, but it
looks to be needed as well.
Signed-off-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The fib metric memory in this case is static in the kernel image,
so we don't need to reference count it since it's never going
to go away on us.
Signed-off-by: David S. Miller <davem@davemloft.net>
TCP is going to record metrics for the connection,
so pre-COW the route metrics at route cache entry
creation time.
This avoids several atomic operations that have to
occur if we COW the metrics after the entry reaches
global visibility.
Signed-off-by: David S. Miller <davem@davemloft.net>
Please note that the IPSEC dst entry metrics keep using
the generic metrics COW'ing mechanism using kmalloc/kfree.
This gives the IPSEC routes an opportunity to use metrics
which are unique to their encapsulated paths.
Signed-off-by: David S. Miller <davem@davemloft.net>
Routing metrics are now copy-on-write.
Initially a route entry points it's metrics at a read-only location.
If a routing table entry exists, it will point there. Else it will
point at the all zero metric place-holder called 'dst_default_metrics'.
The writeability state of the metrics is stored in the low bits of the
metrics pointer, we have two bits left to spare if we want to store
more states.
For the initial implementation, COW is implemented simply via kmalloc.
However future enhancements will change this to place the writable
metrics somewhere else, in order to increase sharing. Very likely
this "somewhere else" will be the inetpeer cache.
Note also that this means that metrics updates may transiently fail
if we cannot COW the metrics successfully.
But even by itself, this patch should decrease memory usage and
increase cache locality especially for routing workloads. In those
cases the read-only metric copies stay in place and never get written
to.
TCP workloads where metrics get updated, and those rare cases where
PMTU triggers occur, will take a very slight performance hit. But
that hit will be alleviated when the long-term writable metrics
move to a more sharable location.
Since the metrics storage went from a u32 array of RTAX_MAX entries to
what is essentially a pointer, some retooling of the dst_entry layout
was necessary.
Most importantly, we need to preserve the alignment of the reference
count so that it doesn't share cache lines with the read-mostly state,
as per Eric Dumazet's alignment assertion checks.
The only non-trivial bit here is the move of the 'flags' member into
the writeable cacheline. This is OK since we are always accessing the
flags around the same moment when we made a modification to the
reference count.
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix dependencies of netfilter realm match: it depends on NET_CLS_ROUTE,
which itself depends on NET_SCHED; this dependency is missing from netfilter.
Since matching on realms is also useful without having NET_SCHED enabled and
the option really only controls whether the tclassid member is included in
route and dst entries, rename the config option to IP_ROUTE_CLASSID and move
it outside of traffic scheduling context to get rid of the NET_SCHED dependeny.
Reported-by: Vladis Kletnieks <Valdis.Kletnieks@vt.edu>
Signed-off-by: Patrick McHardy <kaber@trash.net>
The preferred source address is currently ignored for local routes,
which results in all local connections having a src address that is the
same as the local dst address. Fix this by respecting the preferred source
address when it is provided for local routes.
This bug can be demonstrated as follows:
# ifconfig dummy0 192.168.0.1
# ip route show table local | grep local.*dummy0
local 192.168.0.1 dev dummy0 proto kernel scope host src 192.168.0.1
# ip route change table local local 192.168.0.1 dev dummy0 \
proto kernel scope host src 127.0.0.1
# ip route show table local | grep local.*dummy0
local 192.168.0.1 dev dummy0 proto kernel scope host src 127.0.0.1
We now establish a local connection and verify the source IP
address selection:
# nc -l 192.168.0.1 3128 &
# nc 192.168.0.1 3128 &
# netstat -ant | grep 192.168.0.1:3128.*EST
tcp 0 0 192.168.0.1:3128 192.168.0.1:33228 ESTABLISHED
tcp 0 0 192.168.0.1:33228 192.168.0.1:3128 ESTABLISHED
Signed-off-by: Joel Sing <jsing@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In ip_route_output_slow(), instead of allowing a route to be created on
a not UPed device, report -ENETUNREACH immediately.
# ip tunnel add mode ipip remote 10.16.0.164 local
10.16.0.72 dev eth0
# (Note : tunl1 is down)
# ping -I tunl1 10.1.2.3
PING 10.1.2.3 (10.1.2.3) from 192.168.18.5 tunl1: 56(84) bytes of data.
(nothing)
# ./a.out tunl1
# ip tunnel del tunl1
Message from syslogd@shelby at Dec 22 10:12:08 ...
kernel: unregister_netdevice: waiting for tunl1 to become free.
Usage count = 3
After patch:
# ping -I tunl1 10.1.2.3
connect: Network is unreachable
Reported-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Reviewed-by: Octavian Purdila <opurdila@ixiacom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Flush the routing cache only of entries that match the
network namespace in which the purge event occurred.
Signed-off-by: David S. Miller <davem@davemloft.net>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Like RTAX_ADVMSS, make the default calculation go through a dst_ops
method rather than caching the computation in the routing cache
entries.
Now dst metrics are pretty much left as-is when new entries are
created, thus optimizing metric sharing becomes a real possibility.
Signed-off-by: David S. Miller <davem@davemloft.net>
Make all RTAX_ADVMSS metric accesses go through a new helper function,
dst_metric_advmss().
Leave the actual default metric as "zero" in the real metric slot,
and compute the actual default value dynamically via a new dst_ops
AF specific callback.
For stacked IPSEC routes, we use the advmss of the path which
preserves existing behavior.
Unlike ipv4/ipv6, DecNET ties the advmss to the mtu and thus updates
advmss on pmtu updates. This inconsistency in advmss handling
results in more raw metric accesses than I wish we ended up with.
Signed-off-by: David S. Miller <davem@davemloft.net>
Always go through a new ip4_dst_hoplimit() helper, just like ipv6.
This allowed several simplifications:
1) The interim dst_metric_hoplimit() can go as it's no longer
userd.
2) The sysctl_ip_default_ttl entry no longer needs to use
ipv4_doint_and_flush, since the sysctl is not cached in
routing cache metrics any longer.
3) ipv4_doint_and_flush no longer needs to be exported and
therefore can be marked static.
When ipv4_doint_and_flush_strategy was removed some time ago,
the external declaration in ip.h was mistakenly left around
so kill that off too.
We have to move the sysctl_ip_default_ttl declaration into
ipv4's route cache definition header net/route.h, because
currently net/ip.h (where the declaration lives now) has
a back dependency on net/route.h
Signed-off-by: David S. Miller <davem@davemloft.net>
Use helper functions to hide all direct accesses, especially writes,
to dst_entry metrics values.
This will allow us to:
1) More easily change how the metrics are stored.
2) Implement COW for metrics.
In particular this will help us put metrics into the inetpeer
cache if that is what we end up doing. We can make the _metrics
member a pointer instead of an array, initially have it point
at the read-only metrics in the FIB, and then on the first set
grab an inetpeer entry and point the _metrics member there.
Signed-off-by: David S. Miller <davem@davemloft.net>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Use the macros defined for the members of flowi to clean the code up.
Signed-off-by: Changli Gao <xiaosuo@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When we test rt->fl.iif against zero, we're seeing if it's
an output or an input route.
Make that explicit with some helper functions.
Signed-off-by: David S. Miller <davem@davemloft.net>
It seems idev field in struct rtable has no special purpose, but adding
extra atomic ops.
We hold refcounts on the device itself (using percpu data, so pretty
cheap in current kernel).
infiniband case is solved using dst.dev instead of idev->dev
Removal of this field means routing without route cache is now using
shared data, percpu data, and only potential contention is a pair of
atomic ops on struct neighbour per forwarded packet.
About 5% speedup on routing test.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Roland Dreier <rolandd@cisco.com>
Cc: Sean Hefty <sean.hefty@intel.com>
Cc: Hal Rosenstock <hal.rosenstock@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add __rcu annotations to :
(struct dst_entry)->rt_next
(struct rt_hash_bucket)->chain
And use appropriate rcu primitives to reduce sparse warnings if
CONFIG_SPARSE_RCU_POINTER=y
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no point using RCU for dst we allocate for a very short time
(used once).
Change dst_release() to take DST_NOCACHE into account, but also change
skb_dst_set_noref() to force a refcount increment for such dst.
This is a _huge_ gain, because we dont waste memory to store xx thousand
of dsts. Instead of queueing them to RCU, we can free them instantly.
CPU caches can stay hot, re-using same memory blocks to hold temporary
dsts.
Note : remove unneeded smp_mb__before_atomic_dec(); in dst_release(),
since atomic_dec_return() implies a full memory barrier.
Stress test, 160.000.000 udp frames sent, IP route cache disabled
(DDOS).
Before:
real 0m38.091s
user 0m13.189s
sys 7m53.018s
After:
real 0m29.946s
user 0m12.157s
sys 7m40.605s
For reference, if IP route cache was enabled :
real 0m32.030s
user 0m10.521s
sys 8m15.243s
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change a few checks against the hardcoded broadcast address,
0xffffffff, to ipv4_is_lbcast(). Remove some existing checks
using ipv4_is_lbcast() that are now obviously superfluous.
Signed-off-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
struct dst_ops tracks number of allocated dst in an atomic_t field,
subject to high cache line contention in stress workload.
Switch to a percpu_counter, to reduce number of time we need to dirty a
central location. Place it on a separate cache line to avoid dirtying
read only fields.
Stress test :
(Sending 160.000.000 UDP frames,
IP route cache disabled, dual E5540 @2.53GHz,
32bit kernel, FIB_TRIE, SLUB/NUMA)
Before:
real 0m51.179s
user 0m15.329s
sys 10m15.942s
After:
real 0m45.570s
user 0m15.525s
sys 9m56.669s
With a small reordering of struct neighbour fields, subject of a
following patch, (to separate refcnt from other read mostly fields)
real 0m41.841s
user 0m15.261s
sys 8m45.949s
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit "fib: RCU conversion of fib_lookup()" removed rcu_read_lock() from
__mkroute_output but left a couple of calls to rcu_read_unlock() in there.
This causes lockdep to complain that the rcu_read_unlock() call in
__ip_route_output_key causes a lock inbalance and quickly crashes the
kernel. The below fixes this for me.
Signed-off-by: Dimitris Michailidis <dm@chelsio.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While doing stress tests with IP route cache disabled, and multi queue
devices, I noticed a very high contention on one rwlock used in
neighbour code.
When many cpus are trying to send frames (possibly using a high
performance multiqueue device) to the same neighbour, they fight for the
neigh->lock rwlock in order to call neigh_hh_init(), and fight on
hh->hh_refcnt (a pair of atomic_inc/atomic_dec_and_test())
But we dont need to call neigh_hh_init() for dst that are used only
once. It costs four atomic operations at least, on two contended cache
lines, plus the high contention on neigh->lock rwlock.
Introduce a new dst flag, DST_NOCACHE, that is set when dst was not
inserted in route cache.
With the stress test bench, sending 160000000 frames on one neighbour,
results are :
Before patch:
real 2m28.406s
user 0m11.781s
sys 36m17.964s
After patch:
real 1m26.532s
user 0m12.185s
sys 20m3.903s
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While doing stress tests with a disabled IP route cache, I found
__mkroute_output() was touching three times in_device atomic refcount.
Use RCU to touch it once to reduce cache line ping pongs.
Before patch
time to perform the test
real 1m42.009s
user 0m12.545s
sys 25m0.726s
Profile :
16109.00 26.4% ip_route_output_slow vmlinux
7434.00 12.2% dst_destroy vmlinux
3280.00 5.4% fib_rules_lookup vmlinux
3252.00 5.3% fib_semantic_match vmlinux
2622.00 4.3% fib_table_lookup vmlinux
2535.00 4.1% dst_alloc vmlinux
1750.00 2.9% _raw_read_lock vmlinux
1532.00 2.5% rt_set_nexthop vmlinux
After patch
real 1m36.503s
user 0m12.977s
sys 23m25.608s
14234.00 22.4% ip_route_output_slow vmlinux
8717.00 13.7% dst_destroy vmlinux
4052.00 6.4% fib_rules_lookup vmlinux
3951.00 6.2% fib_semantic_match vmlinux
3191.00 5.0% dst_alloc vmlinux
1764.00 2.8% fib_table_lookup vmlinux
1692.00 2.7% _raw_read_lock vmlinux
1605.00 2.5% rt_set_nexthop vmlinux
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
IPv4 and IPv6 have separate neighbour tables, so
the warning messages should be distinguishable.
[ Add a suitable message prefix on the ipv4 side as well -DaveM ]
Signed-off-by: Ulrich Weber <uweber@astaro.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
__in_dev_get_rtnl(dev_out) is called while RTNL is not held, thus
triggers a lockdep fault.
At this point, we only perform a raw test of dev_out->ip_ptr being NULL,
we dont need to make sure ip_ptr cant changed right after.
We can use rcu_dereference_raw() for this.
Reported-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change "return (EXPR);" to "return EXPR;"
return is not a function, parentheses are not required.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Blackhole routes are used when xfrm_lookup() returns -EREMOTE (error
triggered by IKE for example), hence this kind of route is always
temporary and so we should check if a better route exists for next
packets.
Bug has been introduced by commit d11a4dc18b.
Signed-off-by: Jianzhao Wang <jianzhao.wang@6wind.com>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now cmpxchg() is available on all arches, we can use it in
build_ehash_secret() and rt_bind_peer() instead of using spinlocks.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
CC: Mathieu Desnoyers <mathieu.desnoyers@polymtl.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a new rt attribute, RTA_MARK, and use it in
rt_fill_info()/inet_rtm_getroute() to support following commands :
ip route get 192.168.20.110 mark NUMBER
ip route get 192.168.20.108 from 192.168.20.110 iif eth1 mark NUMBER
ip route list cache [192.168.20.110] mark NUMBER
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
CodingStyle cleanups
EXPORT_SYMBOL should immediately follow the symbol declaration.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Addition of rcu_head to struct inet_peer added 16bytes on 64bit arches.
Thats a bit unfortunate, since old size was exactly 64 bytes.
This can be solved, using an union between this rcu_head an four fields,
that are normally used only when a refcount is taken on inet_peer.
rcu_head is used only when refcnt=-1, right before structure freeing.
Add a inet_peer_refcheck() function to check this assertion for a while.
We can bring back SLAB_HWCACHE_ALIGN qualifier in kmem cache creation.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
remove useless union keyword in rtable, rt6_info and dn_route.
Since there is only one member in a union, the union keyword isn't useful.
Signed-off-by: Changli Gao <xiaosuo@gmail.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
in_dev_get() -> __in_dev_get_rcu() in a rcu protected function.
[ Fix build with CONFIG_IP_ROUTE_VERBOSE disabled. -DaveM ]
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Avoid two atomic ops on output device refcount
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Avoid two atomic ops on struct in_device refcount per incoming packet,
if slow path taken, (or route cache disabled)
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Christoph Lameter mentioned that packets could be dropped in input path
because of rp_filter settings, without any SNMP counter being
incremented. System administrator can have a hard time to track the
problem.
This patch introduces a new counter, LINUX_MIB_IPRPFILTER, incremented
each time we drop a packet because Reverse Path Filter triggers.
(We receive an IPv4 datagram on a given interface, and find the route to
send an answer would use another interface)
netstat -s | grep IPReversePathFilter
IPReversePathFilter: 21714
Reported-by: Christoph Lameter <cl@linux-foundation.org>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch saves 224 bytes of text on my machine.
__this_cpu_inc() generates a single instruction, using no scratch
registers :
65 ff 04 25 a8 30 01 00 incl %gs:0x130a8
instead of :
48 c7 c2 80 30 01 00 mov $0x13080,%rdx
65 48 8b 04 25 88 ea 00 00 mov %gs:0xea88,%rax
83 44 10 28 01 addl $0x1,0x28(%rax,%rdx,1)
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ip_route_input() is the version returning a refcounted dst, while
ip_route_input_noref() returns a non refcounted one.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use low order bit of skb->_skb_dst to tell dst is not refcounted.
Change _skb_dst to _skb_refdst to make sure all uses are catched.
skb_dst() returns the dst, regardless of noref bit set or not, but
with a lockdep check to make sure a noref dst is not given if current
user is not rcu protected.
New skb_dst_set_noref() helper to set an notrefcounted dst on a skb.
(with lockdep check)
skb_dst_drop() drops a reference only if skb dst was refcounted.
skb_dst_force() helper is used to force a refcount on dst, when skb
is queued and not anymore RCU protected.
Use skb_dst_force() in __sk_add_backlog(), __dev_xmit_skb() if
!IFF_XMIT_DST_RELEASE or skb enqueued on qdisc queue, in
sock_queue_rcv_skb(), in __nf_queue().
Use skb_dst_force() in dev_requeue_skb().
Note: dst_use_noref() still dirties dst, we might transform it
later to do one dirtying per jiffies.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A while back there was a discussion regarding the rt_secret_interval timer.
Given that we've had the ability to do emergency route cache rebuilds for awhile
now, based on a statistical analysis of the various hash chain lengths in the
cache, the use of the flush timer is somewhat redundant. This patch removes the
rt_secret_interval sysctl, allowing us to rely solely on the statistical
analysis mechanism to determine the need for route cache flushes.
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sparse can help us find endianness bugs, but we need to make some
cleanups to be able to more easily spot real bugs.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
The the rebuild changes the genid which in turn is used at
the hash calculation. Thus if we don't restart and go on with
inserting the rt will happen in wrong chain.
(Fixed Neil's comment about the index passed into the rt_intern_hash)
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Reviewed-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There's no need in getting it 3 times and gcc isn't smart enough
to understand this himself.
This is just a cleanup before the fix (next patch).
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
TCP sessions over IPv4 can get stuck if routers between endpoints
do not fragment packets but implement PMTU instead, and we are using
those routers because of an ICMP redirect.
Setup is as follows
MTU1 MTU2 MTU1
A--------B------C------D
with MTU1 > MTU2. A and D are endpoints, B and C are routers. B and C
implement PMTU and drop packets larger than MTU2 (for example because
DF is set on all packets). TCP sessions are initiated between A and D.
There is packet loss between A and D, causing frequent TCP
retransmits.
After the number of retransmits on a TCP session reaches tcp_retries1,
tcp calls dst_negative_advice() prior to each retransmit. This results
in route cache entries for the peer to be deleted in
ipv4_negative_advice() if the Path MTU is set.
If the outstanding data on an affected TCP session is larger than
MTU2, packets sent from the endpoints will be dropped by B or C, and
ICMP NEEDFRAG will be returned. A and D receive NEEDFRAG messages and
update PMTU.
Before the next retransmit, tcp will again call dst_negative_advice(),
causing the route cache entry (with correct PMTU) to be deleted. The
retransmitted packet will be larger than MTU2, causing it to be
dropped again.
This sequence repeats until the TCP session aborts or is terminated.
Problem is fixed by removing redirected route cache entries in
ipv4_negative_advice() only if the PMTU is expired.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Xfrm_dst keeps a reference to ipv4 rtable entries on each
cached bundle. The only way to renew xfrm_dst when the underlying
route has changed, is to implement dst_check for this. This is
what ipv6 side does too.
The problems started after 87c1e12b5e
("ipsec: Fix bogus bundle flowi") which fixed a bug causing xfrm_dst
to not get reused, until that all lookups always generated new
xfrm_dst with new route reference and path mtu worked. But after the
fix, the old routes started to get reused even after they were expired
causing pmtu to break (well it would occationally work if the rtable
gc had run recently and marked the route obsolete causing dst_check to
get called).
Signed-off-by: Timo Teras <timo.teras@iki.fi>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
route: Fix caught BUG_ON during rt_secret_rebuild_oneshot()
Call rt_secret_rebuild can cause BUG_ON(timer_pending(&net->ipv4.rt_secret_timer)) in
add_timer as there is not any synchronization for call rt_secret_rebuild_oneshot()
for the same net namespace.
Also this issue affects to rt_secret_reschedule().
Thus use mod_timer enstead.
Signed-off-by: Vitaliy Gusev <vgusev@openvz.org>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We added an automatic route cache rebuilding in commit 1080d709fb
but had to correct few bugs. One of the assumption of original patch,
was that entries where kept sorted in a given way.
This assumption is known to be wrong (commit 1ddbcb005c gave an
explanation of this and corrected a leak) and expensive to respect.
Paweł Staszewski reported to me one of his machine got its routing cache
disabled after few messages like :
[ 2677.850065] Route hash chain too long!
[ 2677.850080] Adjust your secret_interval!
[82839.662993] Route hash chain too long!
[82839.662996] Adjust your secret_interval!
[155843.731650] Route hash chain too long!
[155843.731664] Adjust your secret_interval!
[155843.811881] Route hash chain too long!
[155843.811891] Adjust your secret_interval!
[155843.858209] vlan0811: 5 rebuilds is over limit, route caching
disabled
[155843.858212] Route hash chain too long!
[155843.858213] Adjust your secret_interval!
This is because rt_intern_hash() might be fooled when computing a chain
length, because multiple entries with same keys can differ because of
TOS (or mark/oif) bits.
In the rare case the fast algorithm see a too long chain, and before
taking expensive path, we call a helper function in order to not count
duplicates of same routes, that only differ with tos/mark/oif bits. This
helper works with data already in cpu cache and is not be very
expensive, despite its O(N^2) implementation.
Paweł Staszewski sucessfully tested this patch on his loaded router.
Reported-and-tested-by: Paweł Staszewski <pstaszewski@itcare.pl>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update rcu_dereference() primitives to use new lockdep-based
checking. The rcu_dereference() in __in6_dev_get() may be
protected either by rcu_read_lock() or RTNL, per Eric Dumazet.
The rcu_dereference() in __sk_free() is protected by the fact
that it is never reached if an update could change it. Check
for this by using rcu_dereference_check() to verify that the
struct sock's ->sk_wmem_alloc counter is zero.
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: laijs@cn.fujitsu.com
Cc: dipankar@in.ibm.com
Cc: mathieu.desnoyers@polymtl.ca
Cc: josh@joshtriplett.org
Cc: dvhltc@us.ibm.com
Cc: niv@us.ibm.com
Cc: peterz@infradead.org
Cc: rostedt@goodmis.org
Cc: Valdis.Kletnieks@vt.edu
Cc: dhowells@redhat.com
LKML-Reference: <1266887105-1528-5-git-send-email-paulmck@linux.vnet.ibm.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Add __percpu sparse annotations to net.
These annotations are to make sparse consider percpu variables to be
in a different address space and warn if accessed without going
through percpu accessors. This patch doesn't affect normal builds.
The macro and type tricks around snmp stats make things a bit
interesting. DEFINE/DECLARE_SNMP_STAT() macros mark the target field
as __percpu and SNMP_UPD_PO_STATS() macro is updated accordingly. All
snmp_mib_*() users which used to cast the argument to (void **) are
updated to cast it to (void __percpu **).
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: David S. Miller <davem@davemloft.net>
Cc: Patrick McHardy <kaber@trash.net>
Cc: Arnaldo Carvalho de Melo <acme@ghostprotocols.net>
Cc: Vlad Yasevich <vladislav.yasevich@hp.com>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
/proc/net/rt_acct is not created if NET_CLS_ROUTE=n.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is to be used together with switch technologies, like RFC3069,
that where the individual ports are not allowed to communicate with
each other, but they are allowed to talk to the upstream router. As
described in RFC 3069, it is possible to allow these hosts to
communicate through the upstream router by proxy_arp'ing.
This patch basically allow proxy arp replies back to the same
interface (from which the ARP request/solicitation was received).
Tunable per device via proc "proxy_arp_pvlan":
/proc/sys/net/ipv4/conf/*/proxy_arp_pvlan
This switch technology is known by different vendor names:
- In RFC 3069 it is called VLAN Aggregation.
- Cisco and Allied Telesyn call it Private VLAN.
- Hewlett-Packard call it Source-Port filtering or port-isolation.
- Ericsson call it MAC-Forced Forwarding (RFC Draft).
Signed-off-by: Jesper Dangaard Brouer <hawk@comx.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (1815 commits)
mac80211: fix reorder buffer release
iwmc3200wifi: Enable wimax core through module parameter
iwmc3200wifi: Add wifi-wimax coexistence mode as a module parameter
iwmc3200wifi: Coex table command does not expect a response
iwmc3200wifi: Update wiwi priority table
iwlwifi: driver version track kernel version
iwlwifi: indicate uCode type when fail dump error/event log
iwl3945: remove duplicated event logging code
b43: fix two warnings
ipw2100: fix rebooting hang with driver loaded
cfg80211: indent regulatory messages with spaces
iwmc3200wifi: fix NULL pointer dereference in pmkid update
mac80211: Fix TX status reporting for injected data frames
ath9k: enable 2GHz band only if the device supports it
airo: Fix integer overflow warning
rt2x00: Fix padding bug on L2PAD devices.
WE: Fix set events not propagated
b43legacy: avoid PPC fault during resume
b43: avoid PPC fault during resume
tcp: fix a timewait refcnt race
...
Fix up conflicts due to sysctl cleanups (dead sysctl_check code and
CTL_UNNUMBERED removed) in
kernel/sysctl_check.c
net/ipv4/sysctl_net_ipv4.c
net/ipv6/addrconf.c
net/sctp/sysctl.c
The motivation for an additional notifier in batched netdevice
notification (rt_do_flush) only needs to be called once per batch not
once per namespace.
For further batching improvements I need a guarantee that the
netdevices are unregistered in order allowing me to unregister an all
of the network devices in a network namespace at the same time with
the guarantee that the loopback device is really and truly
unregistered last.
Additionally it appears that we moved the route cache flush after
the final synchronize_net, which seems wrong and there was no
explanation. So I have restored the original location of the final
synchronize_net.
Cc: Octavian Purdila <opurdila@ixiacom.com>
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rewrite statistics accumulation to be in terms of structure fields,
not raw u32 additions. Keep them in same order, though.
This is the last user of create_proc_read_entry() in net/,
please NAK all new ones as well as all new ->write_proc, ->read_proc and
create_proc_entry() users. Cc me if there are problems. :-)
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Generated with the following semantic patch
@@
struct net *n1;
struct net *n2;
@@
- n1 == n2
+ net_eq(n1, n2)
@@
struct net *n1;
struct net *n2;
@@
- n1 != n2
+ !net_eq(n1, n2)
applied over {include,net,drivers/net}.
Signed-off-by: Octavian Purdila <opurdila@ixiacom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On Sun, 2009-11-22 at 16:31 -0800, David Miller wrote:
> It should be of the form:
> if (x &&
> y)
>
> or:
> if (x && y)
>
> Fix patches, rather than complaints, for existing cases where things
> do not follow this pattern are certainly welcome.
Also collapsed some multiple tabs to single space.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While investigating for network latencies, I found inet_getid() was a
contention point for some workloads, as inet_peer_idlock is shared
by all inet_getid() users regardless of peers.
One way to fix this is to make ip_id_count an atomic_t instead
of __u16, and use atomic_add_return().
In order to keep sizeof(struct inet_peer) = 64 on 64bit arches
tcp_ts_stamp is also converted to __u32 instead of "unsigned long".
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that sys_sysctl is a compatiblity wrapper around /proc/sys
all sysctl strategy routines, and all ctl_name and strategy
entries in the sysctl tables are unused, and can be
revmoed.
In addition neigh_sysctl_register has been modified to no longer
take a strategy argument and it's callers have been modified not
to pass one.
Cc: "David Miller" <davem@davemloft.net>
Cc: Hideaki YOSHIFUJI <yoshfuji@linux-ipv6.org>
Cc: netdev@vger.kernel.org
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Conflicts:
drivers/net/usb/cdc_ether.c
All CDC ethernet devices of type USB_CLASS_COMM need to use
'&mbm_info'.
Signed-off-by: David S. Miller <davem@davemloft.net>
Policy routing is not looked up by mark on reverse path filtering.
This fixes it.
Signed-off-by: Jamal Hadi Salim <hadi@cyberus.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use symbols instead of magic constants while checking PMTU discovery
setsockopt.
Remove redundant test in ip_rt_frag_needed() (done by caller).
Signed-off-by: John Dykstra <john.dykstra1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's unused.
It isn't needed -- read or write flag is already passed and sysctl
shouldn't care about the rest.
It _was_ used in two places at arch/frv for some reason.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Cc: David Howells <dhowells@redhat.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: James Morris <jmorris@namei.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Sizing of memory allocations shouldn't depend on the number of physical
pages found in a system, as that generally includes (perhaps a huge amount
of) non-RAM pages. The amount of what actually is usable as storage
should instead be used as a basis here.
Some of the calculations (i.e. those not intending to use high memory)
should likely even use (totalram_pages - totalhigh_pages).
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Acked-by: Rusty Russell <rusty@rustcorp.com.au>
Acked-by: Ingo Molnar <mingo@elte.hu>
Cc: Dave Airlie <airlied@linux.ie>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
Cc: Pekka Enberg <penberg@cs.helsinki.fi>
Cc: Hugh Dickins <hugh.dickins@tiscali.co.uk>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Patrick McHardy <kaber@trash.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
While doing some forwarding benchmarks, I noticed
ip_rt_send_redirect() is rather expensive, even if send_redirects is
false for the device.
Fix is to avoid two atomic ops, we dont really need to take a
reference on in_dev
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Choose saner defaults for xfrm[4|6] gc_thresh values on init
Currently, the xfrm[4|6] code has hard-coded initial gc_thresh values
(set to 1024). Given that the ipv4 and ipv6 routing caches are sized
dynamically at boot time, the static selections can be non-sensical.
This patch dynamically selects an appropriate gc threshold based on
the corresponding main routing table size, using the assumption that
we should in the worst case be able to handle as many connections as
the routing table can.
For ipv4, the maximum route cache size is 16 * the number of hash
buckets in the route cache. Given that xfrm4 starts garbage
collection at the gc_thresh and prevents new allocations at 2 *
gc_thresh, we set gc_thresh to half the maximum route cache size.
For ipv6, its a bit trickier. there is no maximum route cache size,
but the ipv6 dst_ops gc_thresh is statically set to 1024. It seems
sane to select a simmilar gc_thresh for the xfrm6 code that is half
the number of hash buckets in the v6 route cache times 16 (like the v4
code does).
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When route caching is disabled (rt_caching returns false), We still use route
cache entries that are created and passed into rt_intern_hash once. These
routes need to be made usable for the one call path that holds a reference to
them, and they need to be reclaimed when they're finished with their use. To be
made usable, they need to be associated with a neighbor table entry (which they
currently are not), otherwise iproute_finish2 just discards the packet, since we
don't know which L2 peer to send the packet to. To do this binding, we need to
follow the path a bit higher up in rt_intern_hash, which calls
arp_bind_neighbour, but not assign the route entry to the hash table.
Currently, if caching is off, we simply assign the route to the rp pointer and
are reutrn success. This patch associates us with a neighbor entry first.
Secondly, we need to make sure that any single use routes like this are known to
the garbage collector when caching is off. If caching is off, and we try to
hash in a route, it will leak when its refcount reaches zero. To avoid this,
this patch calls rt_free on the route cache entry passed into rt_intern_hash.
This places us on the gc list for the route cache garbage collector, so that
when its refcount reaches zero, it will be reclaimed (Thanks to Alexey for this
suggestion).
I've tested this on a local system here, and with these patches in place, I'm
able to maintain routed connectivity to remote systems, even if I set
/proc/sys/net/ipv4/rt_cache_rebuild_count to -1, which forces rt_caching to
return false.
Signed-off-by: Neil Horman <nhorman@redhat.com>
Reported-by: Jarek Poplawski <jarkao2@gmail.com>
Reported-by: Maxime Bizon <mbizon@freebox.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't drop route if we're not caching
I recently got a report of an oops on a route lookup. Maxime was
testing what would happen if route caching was turned off (doing so by setting
making rt_caching always return 0), and found that it triggered an oops. I
looked at it and found that the problem stemmed from the fact that the route
lookup routines were returning success from their lookup paths (which is good),
but never set the **rp pointer to anything (which is bad). This happens because
in rt_intern_hash, if rt_caching returns false, we call rt_drop and return 0.
This almost emulates slient success. What we should be doing is assigning *rp =
rt and _not_ dropping the route. This way, during slow path lookups, when we
create a new route cache entry, we don't immediately discard it, rather we just
don't add it into the cache hash table, but we let this one lookup use it for
the purpose of this route request. Maxime has tested and reports it prevents
the oops. There is still a subsequent routing issue that I'm looking into
further, but I'm confident that, even if its related to this same path, this
patch makes sense to take.
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For the sake of power saver lovers, use a deferrable timer to fire
rt_check_expire()
As some big routers cache equilibrium depends on garbage collection
done in time, we take into account elapsed time between two
rt_check_expire() invocations to adjust the amount of slots we have to
check.
Based on an initial idea and patch from Tero Kristo
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Tero Kristo <tero.kristo@nokia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Define three accessors to get/set dst attached to a skb
struct dst_entry *skb_dst(const struct sk_buff *skb)
void skb_dst_set(struct sk_buff *skb, struct dst_entry *dst)
void skb_dst_drop(struct sk_buff *skb)
This one should replace occurrences of :
dst_release(skb->dst)
skb->dst = NULL;
Delete skb->dst field
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Define skb_rtable(const struct sk_buff *skb) accessor to get rtable from skb
Delete skb->rtable field
Setting rtable is not allowed, just set dst instead as rtable is an alias.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander V. Lukyanov found a regression in 2.6.29 and made a complete
analysis found in http://bugzilla.kernel.org/show_bug.cgi?id=13339
Quoted here because its a perfect one :
begin_of_quotation
2.6.29 patch has introduced flexible route cache rebuilding. Unfortunately the
patch has at least one critical flaw, and another problem.
rt_intern_hash calculates rthi pointer, which is later used for new entry
insertion. The same loop calculates cand pointer which is used to clean the
list. If the pointers are the same, rtable leak occurs, as first the cand is
removed then the new entry is appended to it.
This leak leads to unregister_netdevice problem (usage count > 0).
Another problem of the patch is that it tries to insert the entries in certain
order, to facilitate counting of entries distinct by all but QoS parameters.
Unfortunately, referencing an existing rtable entry moves it to list beginning,
to speed up further lookups, so the carefully built order is destroyed.
For the first problem the simplest patch it to set rthi=0 when rthi==cand, but
it will also destroy the ordering.
end_of_quotation
Problematic commit is 1080d709fb
(net: implement emergency route cache rebulds when gc_elasticity is exceeded)
Trying to keep dst_entries ordered is too complex and breaks the fact that
order should depend on the frequency of use for garbage collection.
A possible fix is to make rt_intern_hash() simpler, and only makes
rt_check_expire() a litle bit smarter, being able to cope with an arbitrary
entries order. The added loop is running on cache hot data, while cpu
is prefetching next object, so should be unnoticied.
Reported-and-analyzed-by: Alexander V. Lukyanov <lav@yar.ru>
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
rt_check_expire() computes average and standard deviation of chain lengths,
but not correclty reset length to 0 at beginning of each chain.
This probably gives overflows for sum2 (and sum) on loaded machines instead
of meaningful results.
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Right now we have no upper limit on the size of the route cache hash table.
On a 128GB POWER6 box it ends up as 32MB:
IP route cache hash table entries: 4194304 (order: 9, 33554432 bytes)
It would be nice to cap this for memory consumption reasons, but a massive
hashtable also causes a significant spike when measuring OS jitter.
With a 32MB hashtable and 4 million entries, rt_worker_func is taking
5 ms to complete. On another system with more memory it's taking 14 ms.
Even though rt_worker_func does call cond_sched() to limit its impact,
in an HPC environment we want to keep all sources of OS jitter to a minimum.
With the patch applied we limit the number of entries to 512k which
can still be overriden by using the rt_entries boot option:
IP route cache hash table entries: 524288 (order: 6, 4194304 bytes)
With this patch rt_worker_func now takes 0.460 ms on the same system.
Signed-off-by: Anton Blanchard <anton@samba.org>
Acked-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Impact: build fix
API was changed, but not all usage sites were converted:
net/ipv4/route.c: In function ‘ip_rt_init’:
net/ipv4/route.c:3379: error: too few arguments to function ‘__alloc_percpu’
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Tejun Heo <tj@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Base versions handle constant folding now.
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This last patch makes the appropriate changes to use and propagate the
network namespace where needed in IPv4 multicast routing code.
This consists mainly in replacing all the remaining init_net occurences
with current netns pointer retrieved from sockets, net devices or
mfc_caches depending on the routines' contexts.
Some routines receive a new 'struct net' parameter to propagate the current
netns:
* vif_add/vif_delete
* ipmr_new_tunnel
* mroute_clean_tables
* ipmr_cache_find
* ipmr_cache_report
* ipmr_cache_unresolved
* ipmr_mfc_add/ipmr_mfc_delete
* ipmr_get_route
* rt_fill_info (in route.c)
Signed-off-by: Benjamin Thery <benjamin.thery@bull.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
In future all cpumask ops will only be valid (in general) for bit
numbers < nr_cpu_ids. So use that instead of NR_CPUS in iterators
and other comparisons.
This is always safe: no cpu number can be >= nr_cpu_ids, and
nr_cpu_ids is initialized to NR_CPUS at boot.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Mike Travis <travis@sgi.com>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pass netns to xfrm_lookup()/__xfrm_lookup(). For that pass netns
to flow_cache_lookup() and resolver callback.
Take it from socket or netdevice. Stub DECnet to init_net.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I want to compile out proc_* and sysctl_* handlers totally and
stub them to NULL depending on config options, however usage of &
will prevent this, since taking adress of NULL pointer will break
compilation.
So, drop & in front of every ->proc_handler and every ->strategy
handler, it was never needed in fact.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using NIPQUAD() with NIPQUAD_FMT, %d.%d.%d.%d or %u.%u.%u.%u
can be replaced with %pI4
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
call_rcu() will unconditionally rewrite RCU head anyway.
Applies to
struct neigh_parms
struct neigh_table
struct net
struct cipso_v4_doi
struct in_ifaddr
struct in_device
rt->u.dst
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a patch to provide on demand route cache rebuilding. Currently, our
route cache is rebulid periodically regardless of need. This introduced
unneeded periodic latency. This patch offers a better approach. Using code
provided by Eric Dumazet, we compute the standard deviation of the average hash
bucket chain length while running rt_check_expire. Should any given chain
length grow to larger that average plus 4 standard deviations, we trigger an
emergency hash table rebuild for that net namespace. This allows for the common
case in which chains are well behaved and do not grow unevenly to not incur any
latency at all, while those systems (which may be being maliciously attacked),
only rebuild when the attack is detected. This patch take 2 other factors into
account:
1) chains with multiple entries that differ by attributes that do not affect the
hash value are only counted once, so as not to unduly bias system to rebuilding
if features like QOS are heavily used
2) if rebuilding crosses a certain threshold (which is adjustable via the added
sysctl in this patch), route caching is disabled entirely for that net
namespace, since constant rebuilding is less efficient that no caching at all
Tested successfully by me.
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
net: Remove CONFIG_KMOD from net/ (towards removing CONFIG_KMOD entirely)
ipv4: Add a missing rcu_assign_pointer() in routing cache.
[netdrvr] ibmtr: PCMCIA IBMTR is ok on 64bit
xen-netfront: Avoid unaligned accesses to IP header
lmc: copy_*_user under spinlock
[netdrvr] myri10ge, ixgbe: remove broken select INTEL_IOATDMA
rt_intern_hash() is doing an update of a RCU guarded hash chain
without using rcu_assign_pointer() or equivalent barrier.
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
name and nlen parameters passed to ->strategy hook are unused, remove
them. In general ->strategy hook should know what it's doing, and don't
do something tricky for which, say, pointer to original userspace array
may be needed (name).
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Acked-by: David S. Miller <davem@davemloft.net> [ networking bits ]
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: David Howells <dhowells@redhat.com>
Cc: Matt Mackall <mpm@selenic.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
David S. Miller
Eric Dumazet
Thomas Graf
Gao feng
Tim Bird
Eldad Zack
Joe Perches
Eric W. Biederman
Shan Wei
majianpeng
Eric Dumazet
Daniel Baluta
Amir Vadai
Linus Torvalds
David Howells
Benjamin LaHaise
Steffen Klassert
Stephen Rothwell
Julian Anastasov
Flavio Leitner
Vasily Averin
Greg Rose
Dave Jones
Held Bernhard
Michael Smith
OGAWA Hirofumi
Lucas De Marchi
Dan Siemon
Hiroaki SHIMODA
Roland Dreier
Patrick McHardy
Joel Sing
Changli Gao
Andy Walls
Dimitris Michailidis
Ulrich Weber
Jianzhao Wang
Neil Horman
Tejun Heo
Pavel Emelyanov
Guenter Roeck
Timo Teräs
Vitaliy Gusev
Paul E. McKenney
Alexey Dobriyan
Jesper Dangaard Brouer
Octavian Purdila
jamal
John Dykstra
Jan Beulich
Eric Dumazet
Anton Blanchard
Ingo Molnar
Harvey Harrison
Benjamin Thery
Rusty Russell