struct bin_attribute * is needed in bin_attribute ->read()/->write()
now. Incidentally, could people please run the fscking compiler
before and after applying their patch and compare the build logs?
That (and many, many other) would be caught immediately.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use setup_irq() instead of request_irq() to set up system timer
in 68328 timer code. With the old m68knommu irq code this
was safe, but it is not now within the generic irq framework.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use setup_irq() instead of request_irq() to set up system timer
in ColdFire PIT timer code. With the old m68knommu irq code this
was safe, but it is not now within the generic irq framework.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove the unused mach_trap_init function pointer. All use of it
removed with change to using generic irq framework.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use setup_irq() instead of request_irq() to set up system timer
in ColdFire simple timer code. With the old m68knommu irq code this
was safe, but it is not now within the generic irq framework.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The switch to using the generic irq framework removed the
coldfire_trap_init() code, so remove all references to it.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use setup_irq() instead of request_irq() to set up system timer
in 68360 timer code. With the old m68knommu irq code this
was safe, but it is not now within the generic irq framework.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Create prototype for ack_bad_irq() for m68knommu.
Compilation of kernel/irq/handle.c fails without it.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux-2.6:
[IA64] Nail two more simple section mismatch errors
[IA64] fix section mismatch warnings
[IA64] rename partial_page
[IA64] Ensure that machvec is set up takes place before serial console
[IA64] vector-domain - fix vector_table
[IA64] vector-domain - handle assign_irq_vector(AUTO_ASSIGN)
* git://git.kernel.org/pub/scm/linux/kernel/git/sam/kbuild:
kbuild: fix modpost warnings for xtensa
kbuild: be more foregiving on init section naming
kbuild: rearrange a few function in modpost
kbuild: use LDFLAGS_MODULE only for .ko links
kconfig: remove unused members from struct symbol
kconfig: attach help text to menus
kbuild: fix up printing of Linux C Library version in scripts/ver_linux
kbuild: do not do section mismatch checks on vmlinux in 2nd pass
The Xtensa architecture places literal pools in sections separate
from the instructions. The corresponsing text sections, therefore,
reference the .literal section, and we have to suppress those
warnings.
The naming convention defines the name for a literal
section as .SECTION.literal, unless .SECTION is .text. In that case
the name is only .literal. Using strncmp() instead of strcmp()
to compare the from-section with .SECTION.init.refok in pattern 0
should not cause any regressions for other architectures.
We also need to suppress warnings for two informational
sections (.xt.lit and .xt.prop) used by the Xtensa architecture.
Signed-off-by: Chris Zankel <chris@zankel.net>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
pcibios_setup (between 'pci_setup' and 'quirk_mellanox_tavor')
setup_profiling_timer (between 'write_profile' and 'delayed_put_task_struct')
Signed-off-by: Tony Luck <tony.luck@intel.com>
In 741f98fe29 Sam added full
checking across the entire vmlinux image. This flushed out
a dozen new section mismatch warnings. Start the whack-a-mole
game again to stomp them out.
Signed-off-by: Tony Luck <tony.luck@intel.com>
Jens has added a partial_page thing in splice whcih conflicts with the ia64
one. Rename ia64 out of the way. (ia64 chose poorly).
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Tony Luck <tony.luck@intel.com>
In the whitelist function of modpost now use the same
check to identify init_section as in other places of modpost.
This has the effect that we now recognize sections named
.init.text.19 as init sections and we no longer warn
when we see these.
At the same time make surrounding code readable by dropping
use of temporary flags.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Sam Ravnborg pointed out that Documentation/kbuild/makefiles.txt already
says this is what it's for. This patch makes the reality live up to the
documentation. This fixes the problem of LDFLAGS_BUILD_ID getting into too
many places.
Signed-off-by: Roland McGrath <roland@redhat.com>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Roman Zippel wrote:
> A simple example would be
> help texts, right now they are per symbol, but they should really be per
> menu, so archs can provide different help texts for something.
This patch does this and at the same time introduce a few API
funtions used to access the help text.
The relevant api functions are introduced in the various frontends.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Roman Zippel <zippel@linux-m68k.org>
I noticed, when running scripts/ver_linux on both a Gentoo system
and a Slackware system, that the line printing the C library
version looked a little odd. So I fixed it up to be in line with
all the rest.
Old output:
Linux C Library > libc.2.5
New output:
Linux C Library 2.5
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
We already check and warn about section mismatches from vmlinux
(build as vmlinux.o) during first pass so skip the checks
during the 2nd pass where we process modules.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
struct apm_bios_info uses "unsigned short" and "unsigned long"
to mean u16 and u32 respectively. Correct.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Make "struct ist_info" valid on both i386 and x86-64, and use the
structure by name in the setup code. Additionally, "Intel SpeedStep
IST" is redundant, refer to it as IST consistently.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
For APM calls, BX contains the device index, which is zero for
the system BIOS. Disconnect requres BX = 0.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Starting with kernel 2.6.23-rc1, the i386 APM driver fails
on several of my machines with the message:
apm: BIOS not found
This happens because of a bug in the i386 boot code rewrite
from assembler to C. The original assembly code had the
following code in its APM BIOS presence test (boot/setup.S):
andw $0x02, %cx # Is 32 bit supported?
je done_apm_bios # No 32-bit, no (good) APM BIOS
That is, the code bails out if bit 2 is zero.
In the new C version, this is coded as (boot/apm.c):
if (cx & 0x02) /* 32 bits supported? */
return -1;
Here we see that the test has been accidentally inverted.
The fix is to negate the test. I've verified that this
allows the APM driver to work again on my affected machines.
Signed-off-by: Mikael Pettersson <mikpe@it.uu.se>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/selinux-2.6:
SELinux: null-terminate context string in selinux_xfrm_sec_ctx_alloc
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6:
ACPI: Kconfig: remove CONFIG_ACPI_SLEEP from source
ACPI: quiet ACPI Exceptions due to no _PTC or _TSS
ACPI: Remove references to ACPI_STATE_S2 from acpi_pm_enter
ACPI: Kconfig: always enable CONFIG_ACPI_SLEEP on X86
ACPI: Kconfig: fold /proc/acpi/sleep under CONFIG_ACPI_PROCFS
ACPI: Kconfig: CONFIG_ACPI_PROCFS now defaults to N
ACPI: autoload modules - Create __mod_acpi_device_table symbol for all ACPI drivers
ACPI: autoload modules - Create ACPI alias interface
ACPI: autoload modules - ACPICA modifications
ACPI: asus-laptop: Fix failure exits
ACPI: fix oops due to typo in new throttling code
ACPI: ignore _PSx method for hotplugable PCI devices
ACPI: Use ACPI methods to select PCI device suspend state
ACPI, PNP: hook ACPI D-state to PNP suspend/resume
ACPI: Add acpi_pm_device_sleep_state helper routine
ACPI: Implement the set_target() callback from pm_ops
Parse the machvec command line option outside of the early_param()
so that ia64_mv is set before any console intialisation that
may result from early_param parsing.
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Tony Luck <tony.luck@intel.com>
This change fixes a panic when assign_irq_vector(irq) is called with
irq = AUTO_ASSIGN.
Signed-off-by: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Currently most of the m68knommu cpu/board setup files are handling
the setup of fixed boot parameters (via CONFIG_BOOTPARAM) themselves.
Move all this into the common setup code.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add configure support for the Intec Wildfire and WildFireMod boards.
Signed-Off-By: Steve Bennett <steveb@workware.net.au>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
It is useless to preserve THREAD_SR in `resume'. The real user's sr
is actually in the stack. We also don't need to disable interrupts :
we'll never be in an invalid state, the sp switch is atomic.
Signed-off-by: Philippe De Muyter <phdm@macqel.be>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Need an include/asm-m68knommu/hw_irq.h for kernel/hrtimer.c
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix a small typo in the definition of MCFDMA_DIR_INV (MCF5272 specific).
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add build support for the new Arcturus boards.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Need to explicitly include linux/device.h.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
CLOCK_TICK_RATE should give the underlying frequency of the tick timer,
to make ntp happy. For Coldfires, that's the main clock.
Signed-off-by: Philippe De Muyter <phdm@macqel.be>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add configure support for the Arcturus UC5272 and UC5282 boards.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove the legacy power management code from the 68328 serial driver.
It is not used, and there is no current kernel support for power
management on the 68328.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This avoids xtime lag seen with dynticks, because while 'xtime' itself
is still not updated often, we keep a 'xtime_cache' variable around that
contains the approximate real-time that _is_ updated each time we do a
'update_wall_time()', and is thus never off by more than one tick.
IOW, this restores the original semantics for 'xtime' users, as long as
you use the proper abstraction functions (ie 'current_kernel_time()' or
'get_seconds()' depending on whether you want a timespec or just the
seconds field).
[ Updated Patch. As penance for my sins I've also yanked another #ifdef
that was added to avoid the xtime lag w/ hrtimers. ]
Signed-off-by: John Stultz <johnstul@us.ibm.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This avoids use of the kernel-internal "xtime" variable directly outside
of the actual time-related functions. Instead, use the helper functions
that we already have available to us.
This doesn't actually change any behaviour, but this will allow us to
fix the fact that "xtime" isn't updated very often with CONFIG_NO_HZ
(because much of the realtime information is maintained as separate
offsets to 'xtime'), which has caused interfaces that use xtime directly
to get a time that is out of sync with the real-time clock by up to a
third of a second or so.
Signed-off-by: John Stultz <johnstul@us.ibm.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
xfrm_audit_log() expects the context string to be null-terminated
which currently doesn't happen with user-supplied contexts.
Signed-off-by: Venkat Yekkirala <vyekkirala@TrustedCS.com>
Acked-by: Stephen Smalley <sds@tycho.nsa.gov>
Signed-off-by: James Morris <jmorris@namei.org>
0x0f 0x01 instructions (ie lgdt, lidt, smsw, lmsw and invlpg) does
not use writeback. This patch set no_wb=1 when emulating those
instructions.
This fixes a regression booting the FreeBSD kernel on AMD.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Signed-off-by: Avi Kivity <avi@qumranet.com>
Testing the wrong bit caused kvm not to disable nx on the guest when it is
disabled on the host (an mmu optimization relies on the nx bits being the
same in the guest and host).
This allows Windows to boot when nx is disabled on te host (e.g. when
host pae is disabled).
Signed-off-by: Avi Kivity <avi@qumranet.com>
Al Viro
Greg Ungerer
Linus Torvalds
Sam Ravnborg
Tony Luck
akpm@linux-foundation.org
Roland McGrath
Jesper Juhl
H. Peter Anvin
Mikael Pettersson
Horms
Kenji Kaneshige
Yasuaki Ishimatsu
Philippe De Muyter
David Wu
john stultz
Venkat Yekkirala
Aurelien Jarno
Avi Kivity