In OSD2r05 draft each attribute list element header was changed
so attribute-value would be 8 bytes aligned. In OSD2r01-r04
it was aligned on 2 bytes. (This is because in OSD2r01 the complete
element was 8 bytes padded at end but the header was not adjusted
and caused permanent miss-alignment.)
OSD1 elements are not padded and might be or might not be aligned.
OSD1 is still supported.
In this code we do all the code re-factoring to separate OSD1/OSD2
differences but do not change actual wire format. All wire format
changes will happen in one patch later, for bisect-ability.
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
bio_map_kern() returns an ERR_PTR() not NULL.
Found by smatch (http://repo.or.cz/w/smatch.git). Compile tested.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Here's a fix for hotplug events. The useage of queue_delayed_work seems
to broke the fifo for processing of firmware events. After several iterations
of adding and removing cabling connected to jbods, the devices are not
getting added becuase kernel thread is activited out of order.
Signed-off-by: Eric Moore <eric.moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Diagnostic buffer support is already there in the driver. This support allows
applications to pull ring buffers from controller firmware for debugging
firmware related issues.
What this patch does is sends reqeust to firmware to release the buffers prior
to host reset. This will allow what ever debug info is there prior to reset
to be dma'd to host memory. With out this fix, some of the debug data would
been lost.
Signed-off-by: Eric Moore <eric.moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Bug fix in the broadcast primative async event code where the driver would
stop sending tm queries after the first queury was completed. This was due
driver not reseting the tm_cmds.status field back to MPT2_CMD_NOT_USED after
completing a task management request.
An addtional fix adding sanity check to insure sas_device->starget set to NULL.
During multipath testing fail over/fail back, the mid layer was holding onto
sdev longer than the fail back period, thus starget was getting set to NULL
for device being added.
Signed-off-by: Eric Moore <eric.moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The Dell branding along with the VID, DID, SSVID, SSDID following the LSI
branding that contains the card firmware/chip/bios versions. If the SSDID
is not known but it is a Dell HBA, the driver will print the SSDID instead
of the Dell branding string. Nothing will be printed for non Dell HBAs
Signed-off-by: Eric Moore <eric.moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The driver name needs to be at the beginining of the driver_version string in
MPT2IOCINFO ioctl. This is the same behaviour is there already in the mptsas
driver.
Signed-off-by: Eric Moore <eric.moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The driver is not freeing message frame when returning failure from
_ctl_do_task_abort. If you call this function 500 times when its unable
to find an active task mid, you end up with no message frames.
Signed-off-by: Eric Moore <eric.moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
There is a bug in firmware where the reply message frame says there is a
16kb sense buffer, when in reality its only 20 bytes. This fix insures
the memcpy action doesn't corrupte the memory beyond the 90 bytes allocated in
the scsi command for sense buffer.
Signed-off-by: Eric Moore <eric.moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The poison sanity check on the reply_post_free register needs to be by 32bit,
not 64bit. The poison check is there because its possible that the driver read
the 1st 32bit before the 2nd 32bit has been written to by firmware. In other
words, this handles race between driver reading the 64 bit register, and it
being dma'd across pci memory from controller firmware as two 32bit pci writes.
Signed-off-by: Eric Moore <eric.moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The current magic number is shared with mptsas driver. This to be unique to
fix issues with register_ioctls32_conversion in older kernels. We are making
this change across all versions of the sas2.0 drivers.
Signed-off-by: Eric Moore <eric.moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Shifting an unsigned char implicitly casts it to a signed int. This
caused 'lba' to sign-extend and Linux would then try READ CAPACITY 16
which was not supported by at least one drive. Using the
get_unaligned_be*() helpers keeps us from having to worry about how the
extension might occur.
Signed-off-by: Dave Hansen <dave@linux.vnet.ibm.com>
Reviewed-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The ata_sas_slave_configure was changed such that it now allocates
some memory for a drain buffer for ATAPI devices. Fixup the ipr
driver such that we no longer make this call with interrupts disabled.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The FCoE forwarder (FCF) would be selected, but then would soon time
out after three advertisements were missed. This would be 24 seconds
by default, or 3 times the keep-alive interval configured on the switch.
The cause was that the multicast address for all FIP E-nodes
was never added.
Signed-off-by: Joe Eykholt <jeykholt@cisco.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
When building with a .config generated from 'make allmodconfig'
some build warnings are generated. This patch corrects the warnings,
adds a FC_FID_NONE (= 0) enumeration for FC-IDs and cleans up one
variable naming to meet our variable naming conventions. For example,
fc_lport's should be named "lport," not "lp."
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Chris Leech <christopher.leech@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
These probably never should have been exported.
If they were needed outside of the fcoe module, they
would have been moved to libfcoe.
Signed-off-by: Chris Leech <christopher.leech@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
sk_buff pointers should use kfree_skb() instead of vanilla kfree().
Found by smatch (http://repo.or.cz/w/smatch.git).
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
When a delete event is queued for an rport, set state to NONE so that no
other processing is done on the rport as it is being removed.
Signed-off-by: Abhijeet Joglekar <abjoglek@cisco.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
After lport_destroy, the local port should not be used again. Transition
to state NONE, any incoming frames or link up should not transition out
of this state since we are deleting exchange table and cleaning up the
local port. Also, mark link as down.
Signed-off-by: Abhijeet Joglekar <abjoglek@cisco.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
We want to generate the rport queue event (from the logoff)
before flushing the queue otherwise the event may still be
in the queue when we logoff.
Signed-off-by: Abhijeet Joglekar <abjoglek@cisco.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Rogue ports are currently not tracked on any list. The only reference
to them is through any outstanding exchanges pending on the rogue ports.
If the module is removed while a retry is set on a rogue port
(say a Plogi retry for instance), this retry is not cancelled because there
is no reference to the rogue port in the discovery rports list. Thus the
local port can clean itself up, delete the exchange pool, and then the
rogue port timeout can fire and try to start up another exchange.
This patch tracks the rogue ports in a new list disc->rogue_rports. Creating
a new list instead of using the disc->rports list keeps remote port code
change to a minimum.
1) Whenever a rogue port is created, it is immediately added to the
disc->rogue_rports list.
2) When the rogues port goes to ready, it is removed from the rogue list
and the real remote port is added to the disc->rports list
3) The removal of the rogue from the disc->rogue_rports list is done in
the context of the fc_rport_work() workQ thread in discovery callback.
4) Real rports are removed from the disc->rports list like before. Lookup
is done only in the real rports list. This avoids making large changes
to the remote port code.
5) In fc_disc_stop_rports, the rogues list is traversed in addition to the
real list to stop the rogue ports and issue logoffs on them. This way, rogue
ports get cleaned up when the local port goes away.
6) rogue remote ports are not removed from the list right away, but
removed late in fc_rport_work() context, multiple threads can find the same
remote port in the list and call rport_logoff(). Rport_logoff() only
continues with the logoff if port is not in NONE state, thus preventing
multiple logoffs and multiple list deletions.
7) Since the rport is removed from the disc list at a later stage
(in the disc callback), incoming frames can find the rport even if
rport_logoff() has been called on the rport. When rport_logoff() is called,
the rport state is set to NONE, and we are trying to cancel all exchanges
and retries on that port. While in this state, if an incoming
Plogi/Prli/Logo or other frames match the rport, we should not reply
because the rport is in the NONE state. Just drop the frame, since the
rport will be deleted soon in the disc callback (fc_rport_work)
8) In fc_disc_single(), remove rport lookup and call to fc_disc_del_target.
fc_disc_single() is called from recv_rscn_req() where rport lookup
and rport_logoff is already done.
Signed-off-by: Abhijeet Joglekar <abjoglek@cisco.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
For instance, if there is a Plogi pending (remote port is in Plogi state),
and the state changes to say NONE (because the port is being logged off),
then when the Plogi resp times out, do not start a retry.
This patch partially reverts an earlier patch (libfc: check for err when
recv and state is incorrect), by moving the state check back to before
checking for error. However, if the state does not match, then there is
an additional check to see if its an error ptr or a real frame before
jumping to err or out respectively.
Signed-off-by: Abhijeet Joglekar <abjoglek@cisco.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
gpn_ft_resp processing currently does not hold the discovery lock.
disc_done() thus gets called from gpn_ft_resp or from gpn_ft_parse
without the lock held. This then sets disc->pending to zero or calls
gpn_ft_req() without disc_lock held.
- Hold disc mutex during gpn_ft resp processing
- In disc_done, release the disc mutex while calling lport callback
Signed-off-by: Abhijeet Joglekar <abjoglek@cisco.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
(version 2)
Fixed a bug in calculating ddp map range when search for free entries:
it was going beyond the end by one, thus corrupting gl_skb[0].
Signed-off-by: Karen Xie <kxie@chelsio.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
When doing a lot (128) of large writes (256K) we can hit the cxgb3_snd_win
check pretty easily. The driver's xmit thread then takes 100% of the cpu.
The driver should not be returning -EAGAIN for this problem. It should
be returing -ENOBUFS, then when the window is opened again it should
queue the xmit thread (it already wakes the xmit thread).
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
cxgb3i was setting can_queue to only 128 commands, and was
setting the can_queue and cmd_per_lun to the same value.
This sets the can_queue to 1024 commands, and sets the cmd_per_lun
to a safer default of 32.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Set target can queue limit to the number of preallocated
session tasks we have.
This along with the cxgb3i can_queue patch will fix a throughput
problem where it could only queue one LU worth of data at a time.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
If a command's scsi cmd pdu setup fails then we can just fail
the IO to the scsi layer. If a DATA_OUT for a R2T fails then
we will want to drop the session, because it means we got a
bad request from the target (iscsi protocol error).
This patch has us propogate the error upwards so libiscsi_tcp
or libiscsi can decide what the best action is to take. It
also fixes a bug where we could try to grab the session lock
while holding it, because if iscsi_tcp drops the session in the
pdu setup callout the session lock is held when setting up the
scsi cmd pdu.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The zfcp_port might have been removed, while the FC fast_io_fail timer
is still running and could trigger the terminate_rport_io callback.
Set the pointer to the zfcp_port to NULL and check accordingly
before using it.
Reviewed-by: Martin Petermann <martin@linux.vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Before dropping the reference count with zfcp_adapter_put, increase it
with zfcp_adapter_get when issuing cfdc requests.
Reviewed-by: Martin Petermann <martin@linux.vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
If this problem appears zfcp ports cannot be de-queued since it is
checked for a zero refcount. The port reference counting is wrong for
existing zfcp ports when e.g. an adapter gets on-line again. During
port scanning the reference counting for existing ports should not be
changed.
Signed-off-by: Martin Petermann <martin.petermann@de.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The current sbal counting can be wrong if a fsf request is
waiting for free sbals and at the same time qdio request queue
is shutdown and re-opened. Revering a previous patch fixes this
issue.
Signed-off-by: Martin Petermann <martin.petermann@de.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
When the abort handler cannot find a pending FSF request, the request
completion could just be running. This means we cannot return SUCCESS,
since this would lead to call to scsi_done after exiting the SCSI
error handler which is not allowed.
Reviewed-by: Martin Petermann <martin@linux.vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
A remote port remains in error state even if we receive a RSCN
stating that the connection is re-established. The port recovery
is not started due to a flag which is not reset.
The solution is to clear the flag in question before we trigger a ERP.
Signed-off-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Error codes specific to the control file requests are evaluated by the
actcli tool, so don't report -ENXIO for those. Generic problems are
still checked for outside the command specific handler.
Reviewed-by: Martin Petermann <martin@linux.vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
On some hardware it can take some time to add a unit. If
some remove this unit during this process the remove will
fail.
Signed-off-by: Martin Petermann <martin@linux.vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The remote port remains in error state even if the connection
is re-established. A wrong precondition check was performed on
the port status leading to a cancellation of the port reopen.
Remove the pre-req check because it's not required and better
handled within the ERP.
Signed-off-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The ERP thread is performing a task before it is executing the
corresponding down on the semaphore. The response handler of the
just started exchange config should wait for the completion by
performing a down on this semaphore. Since this semaphore is still
positive from the ERP enqueue the handler won't wait and therefore
the exchange config will always fail leaving the adapter in error.
The problem can be solved by performing the down on the semaphore
before starting an ERP task. This is the logically correct order.
Only walk the ERP loop if there is a task to perform.
Signed-off-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The nameserver port might be in state online when the adapter is
offlined. On adapter reactivation the nameserver port is not
re-opened due to the PORT_ONLINE status. This results in an
unsuccessful recovery. In forcing the nameserver port status
to offline on all adapter offline events this issue is prevented.
Waiting for the reference count to drop to zero in
zfcp_wka_port_offline is not required, so remove it.
Signed-off-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
When running the scsi_scan from the zfcp workqueue and the target
device does not respond, the zfcp workqueue can block until the
scsi_scan hits a timeout. Move the work to the scsi host workqueue,
since this one is also used for the scan from the SCSI midlayer.
Signed-off-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Fix problem that zfcp_fsf_exchange_config_data_sync and
zfcp_fsf_exchange_config_data_sync could try to call zfcp_fsf_req_free
with a NULL pointer.
Reviewed-by: Martin Petermann <martin@linux.vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Since we're setting the host port type now to FC_PORTTYPE_NPIV
for adapters running in NPIV mode we should allow this port type
for auto-port scanning as well.
Signed-off-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Avoid referencing a fsf request after sending it in fcp_fsf_req_send,
it might have already completed and deallocated.
Signed-off-by: Martin Petermann <martin@linux.vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
We cannot call blk_plug_device from scsi_target_queue_ready
because the q lock is not held. And we do not need to call
it from there because when we return 0, the scsi_request_fn
not_ready handling will plug the queue for us if needed.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Update driver version to 8.3.1
Also update copyright end year for driver.
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
8.3.1 Fixes/Changes :
- Fix incorrect byte-swapping on word 4 of IOCB (data length) which
caused LUNs to not be discovered on big-endian (e.g. PPC)
- Remove a bad cast of MBslimaddr which loses the __iomem (sparse)
- Make lpfc_debugfs_mask_disc_trc static (sparse)
- Correct misspelled word BlockGuard in lpfc_logmsg.h comment
- Replaced repeated code segment for canceling IOCBs from a list with
a function call, lpfc_sli_cancel_iocbs().
- Increased HBQ buffers to support 40KB SSC sequences.
- Added sysfs interface to update speed and topology parameter without
link bounce.
- Fixed bug with sysfs fc_host WWNs not being updated after changing
the WWNs.
- Check if the active mailbox is NULL in the beginning of the mailbox
timeout handler - fixes panic in the mailbox timeout handler while
running IO stress test
- Fixed system panic in lpfc_pci_remove_one() due to ndlp indirect
reference to phba through vport
- Removed de-reference of scsi device after call to scsi_done() to fix
panic in scsi completion path while accessing scsi device after
scsi_done is called.
- Fixed "Nodelist not empty" message when unloading the driver after
target reboot test
- Added LP2105 HBA model description
- Added code to print all 16 words of unrecognized ASYNC events
- Fixed memory leak in vport create + delete loop
- Added support for handling dual error bit from HBA
- Fixed a driver NULL pointer dereference in lpfc_sli_process_sol_iocb
- Fixed a discovery bug with FC switch reboot in lpfc_setup_disc_node
- Take NULL termintator into account when calculating available buffer space
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
blk_rq_unmap_user() returns EFAULT if a program passes an invalid
address to kernel (the kernel fails to copy data to user space). sg
needs to pass the returned value to user space instead of ignoring
it. Before the block layer conversion, sg returns EFAULT
properly. This restores the old behavior.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
So, what's happening here is that the drive is reporting a sense of
2/4/1 ("logical unit is becoming ready") from sr_test_unit_ready(), and
then we ask for the media event notification before checking that result
at all. The check_media_event_descriptor() call isn't getting a check
condition, but it's also reporting that the tray is closed and that
there's no media. In actuality it doesn't yet know if there's media or
not, but there's no way to express that in the media event status field.
My current thought is that if it told us the device isn't yet ready, we
should return that immediately, since there's nothing that'll tell us
any more data than that reliably:
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
isdn: document Kernel CAPI driver interface
Create a file Documentation/isdn/INTERFACE.CAPI describing the
interface between the kernel CAPI subsystem and ISDN device drivers,
analogous to the existing Documentation/isdn/INTERFACE for the old
isdn4linux subsystem. Also add kerneldoc comments to the exported
functions in drivers/isdn/capi/kcapi.c.
Impact: Documentation
Signed-off-by: Tilman Schmidt <tilman@imap.cc>
Signed-off-by: Karsten Keil <keil@b1-systems.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current code writes the PME enabled bit in PCI config space which is
wrong. This was needed for pre-release hardware, and was not removed from
the driver. Also, we need to clear the WUS (wake up status) after we
resume. Otherwise we can't wake for the same event again since it's still
asserted in the hardware. Plus, the multicast lists were being written
improperly, causing multicast WoL to fail.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
From: Stephen Hemminger <shemminger@vyatta.com>
The veth driver will oops if sysfs hooks are open while module is removed.
The net device destructor can not point to code in a module; basically
there are only two possible safe values: NULL - no destructor, or
free_netdev - free on last use
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the tx_timeout() to properly handle the clean up of the
tx ring. It also sets the tx put pointer back to the correct position to
be in sync with HW.
Signed-off-by: Ayaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If we failed to allocate new fragments for receive buffer,
the packet should be dropped and packets should be reused.
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case of mlx4_en_activate_cq() failure, the cleanup
code would go to rx_err and try to disable unactivated rings.
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
Although we already have entry for ZEPHYR the match is done
on product name whereas B-2130 BIOS has it in board name.
Reported-by: Yuriy Zhuravlev <stalkerg@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The virtio-rng drivers checks for spurious callbacks. Since
callbacks can be implemented via shared interrupts (e.g. PCI) this
could lead to guest kernel oopses with lots of virtio devices.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6: (34 commits)
ACPI, i915: Register ACPI video even when not modesetting
Revert "ACPICA: delete check for AML access to port 0x81-83"
I/O port protection: update for windows compatibility.
sony-laptop: always try to unblock rfkill on load
sony-laptop: fix bogus error message display on resume
ACPI: EC: Fix ACPI EC resume non-query interrupt message
sony-laptop: SNC input event 38 fix
sony-laptop: SNC 127 Initialization Fix
sony-laptop: Duplicate SNC 127 Event Fix
ACPI: prevent processor.max_cstate=0 boot crash
ACPI/hpet: prevent boot hang when hpet=force used on ICH-4M
ACPI: delete obsolete "bus master activity" proc field
ACPI: idle: mark_tsc_unstable() at init-time, not run-time
ACPI: add /sys/firmware/acpi/interrupts/sci_not counter
ACPI video: fix an error when the brightness levels on AC and on Battery are same
acpi-cpufreq: Do not let get_measured perf depend on internal variable
acpi-cpufreq: style-only: add parens to math expression
acpi-cpufreq: Cleanup: Use printk_once
x86, acpi_cpufreq: Fix the NULL pointer dereference in get_measured_perf
thinkpad-acpi: bump up version to 0.23
...
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6:
USB: pwc : do not pass stack allocated buffers to USB core.
USB: otg: Fix bug on remove path without transceiver
USB: correct error handling in cdc-wdm
USB: removal of tty->low_latency hack dating back to the old serial code
USB: serial: sierra driver bug fix for composite interface
USB: gadget: omap_udc uses platform_driver_probe()
USB: ci13xxx_udc: fix build error
USB: musb: Prevent multiple includes of musb.h
USB: pass mem_flags to dma_alloc_coherent
USB: g_file_storage: fix use-after-free bug when closing files
USB: ehci-sched.c: EHCI SITD scheduling bugfix
USB: fix mos7840 problem with minor numbers
USB: mos7840: add new device id
USB: musb: fix build when !CONFIG_PM
USB: musb: Remove my email address from few musb related drivers
USB: Gadget: MIPS CI13xxx UDC bugfixes
USB: Unusual Device support for Gold MP3 Player Energy
USB: serial: fix lifetime and locking problems
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k:
m68k: Update defconfigs for 2.6.30-rc3
m68k,m68knommu: Wire up preadv and pwritev
scsi: a4000 - Correct driver unregistration in case of failure
* 'for-linus' of git://git390.marist.edu/pub/scm/linux-2.6:
[S390] update default configuration.
[S390] omit frame pointers on s390 when possible
[S390] Use tape_generic_offline directly.
[S390] /proc/stat idle field for idle cpus
[S390] appldata: avoid deadlock with appldata_mem
[S390] ipl: fix compile breakage
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/bart/ide-2.6:
MAINTAINERS: update IDE entry
palm_bk3710: palm_bk3710_udmatimings[] CodingStyle fixup
palm_bk3710: those registers/bitfields don't exist
mediabay: fix build for CONFIG_BLOCK=n
ide: Stop disks on reboot for laptop which cuts power
ide-cd: fix kernel crash on hppa regression
palm_bk3710: UDMA performance fix
The release path for a disconnected device frees the object then unlocks
the mutex in the freed object...
Found by Dan Carpenter using Smatch
Signed-off-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove my name and emailaddress from note in the source. Wincor Nixdorf
only has some ITE-chips on their mainboards, other chips are not
available for me for testing.
Signed-off-by: Niels de Vos <niels.devos@wincor-nixdorf.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://git.kernel.dk/linux-2.6-block:
cfq-iosched: cache prio_tree root in cfqq->p_root
cfq-iosched: fix bug with aliased request and cooperation detection
cfq-iosched: clear ->prio_trees[] on cfqd alloc
block: fix intermittent dm timeout based oops
umem: fix request_queue lock warning
block: simplify I/O stat accounting
pktcdvd.h should include mempool.h
cfq-iosched: use the default seek distance when there aren't enough seek samples
cfq-iosched: make seek_mean converge more quickly
block: make blk_abort_queue() ignore non-request based devices
block: include empty disks in /proc/diskstats
bio: use bio_kmalloc() in copy/map functions
bio: fix bio_kmalloc()
block: fix queue bounce limit setting
block: fix SG_IO vector request data length handling
scatterlist: make sure sg_miter_next() doesn't return 0 sized mappings
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (94 commits)
netfilter: ctnetlink: fix gcc warning during compilation
net/netrom: Fix socket locking
netlabel: Always remove the correct address selector
ucc_geth.c: Fix upsmr setting in RMII mode
8139too: fix HW initial flow
af_iucv: Fix race when queuing incoming iucv messages
af_iucv: Test additional sk states in iucv_sock_shutdown
af_iucv: Reject incoming msgs if RECV_SHUTDOWN is set
af_iucv: fix oops in iucv_sock_recvmsg() for MSG_PEEK flag
af_iucv: consider state IUCV_CLOSING when closing a socket
iwlwifi: DMA fixes
iwlwifi: add debugging for TX path
mwl8: fix build warning.
mac80211: fix alignment calculation bug
mac80211: do not print WARN if config interface
iwl3945: use cancel_delayed_work_sync to cancel rfkill_poll
iwlwifi: fix EEPROM validation mask to include OTP only devices
atmel: fix netdev ops conversion
pcnet_cs: add cis(firmware) of the Allied Telesis LA-PCM
mlx4_en: Fix cleanup if workqueue create in mlx4_en_add() fails
...
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc:
powerpc: Fix modular build of ide-pmac when mediabay is built in
powerpc/pasemi: Fix build error on UP
powerpc: Make macintosh/mediabay driver depend on CONFIG_BLOCK
maintainers: Fix PS3 patterns
powerpc/ps3: Fix CONFIG_PS3_FLASH=n build warning
powerpc/32: Don't clobber personality flags on exec
powerpc: Fix crash on CPU hotplug
powerpc/85xx: Remove defconfigs that mpc85xx_{smp_}defconfig cover
powerpc/85xx: Added SMP defconfig
powerpc/85xx: Enabled a bunch of FSL specific drivers/options
powerpc/85xx: Updated generic mpc85xx_defconfig
powerpc: don't disable SATA interrupts on Freescale MPC8610 HPCD
fsl_rio: Pass the proper device to dma mapping routines
powerpc: Fix of_node_put() exit path in of_irq_map_one()
powerpc/5200: defconfig updates
powerpc/5200: Add FLASH nodes to lite5200 device tree
powerpc/device-tree: Document MTD nodes with multiple "reg" tuples
powerpc/of-device-tree: Factor MTD physmap bindings out of booting-without-of
powerpc/5200: Bring the legacy fsl_spi_platform_data hooks back
The hash tables contains some of the mapping
so its really nice to have it for the deletion phase.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This line that checks the DRM_CONTROL_ALLOW flag was missed from the KMS
merge. Re-add the check on the IOCTL, as this is currently the only use of
this flag.
Signed-off-by: Jonas Bonn <jonas@southpole.se>
Signed-off-by: Dave Airlie <airlied@redhat.com>
We have a drm_set_config which takes a crtc/encoder/mode setup,
and checks it to see if it can shortcut and just do a base setup,
or whether a complete mode setting is required.
Signed-off-by: Dave Airlie <airlied@redhat.com>
We already added support, just need to let userspace
know when it can use them.
Signed-off-by: Maciej Cencora <m.cencora@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The ACPI video driver defers registration to the i915 driver if the
system supports opregion-mediated backlight control. This registration
was only being performed in the KMS case. Ensure it's done even if we
don't have modesetting enabled.
http://bugzilla.kernel.org/show_bug.cgi?id=13048
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Len Brown <len.brown@intel.com>
This reverts commit fdbdc7fc79.
That temporary quick-fix is no longer necessary,
as the previous patch, a65131e942,
"I/O port protection: update for windows compatibility"
should handle this issue for all ports, including this one.
Signed-off-by: Len Brown <len.brown@intel.com>
For windows compatibility,
1) On a port protection violation, simply ignore the request and
do not return an exception (allow the control method to continue execution.)
2) If only part of the request overlaps a protected port,
read/write the individual ports that are not protected.
http://bugzilla.kernel.org/show_bug.cgi?id=13036
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
This fixes an inconsistent behaviour when loading the driver with the
switch on or off. In the former case you would also need to soft unblock
the switch via the sysfs file entries to really disable rfkill, in the
latter you wouldn't.
Signed-off-by: Mattia Dongili <malattia@linux.it>
Cc: Matthias Welwarsky <matze@welwarsky.de>
Acked-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Len Brown <len.brown@intel.com>
sony_backlight_update_status returns 0 on success -1 on failure (i.e.: the
return value from acpi_callsetfunc. The return value in the resume path
was broken and thus always displaying a bogus warning about not being able
to restore the brightness level.
Signed-off-by: Mattia Dongili <malattia@linux.it>
Signed-off-by: Len Brown <len.brown@intel.com>
When resuming from standby (on a laptop) I see the following message in
my kernel.log:
"ACPI: EC: non-query interrupt received, switching to interrupt mode"
This apparently prevented sony-laptop to properly restore the brightness
level on resume.
The cause: In drivers/acpi/ec.c the acpi_ec_suspend function clears the
GPE mode bit, but this is not restored in acpi_ec_resume (the function
below it). The patch below fixes this by properly restoring the GPE_MODE
bit. Tested and confirmed to work.
Signed-off-by: Almer S. Tigelaar <almer@gnome.org>
Signed-off-by: Mattia Dongili <malattia@linux.it>
Acked-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Signed-off-by: Len Brown <len.brown@intel.com>
Fixes the "unknown input event 38" messages. ANYBUTTON_RELEASED is now
treated the same way as FN_KEY_RELEASED.
Signed-off-by: Almer S. Tigelaar <almer@gnome.org>
Signed-off-by: Mattia Dongili <malattia@linux.it>
Signed-off-by: Len Brown <len.brown@intel.com>
Fixes additional special key initialization for SNC 127 key events.
Verified / tested on a Sony VAIO SR model.
Signed-off-by: Almer S. Tigelaar <almer@gnome.org>
Signed-off-by: Mattia Dongili <malattia@linux.it>
Signed-off-by: Len Brown <len.brown@intel.com>
Fixes a duplicate mapping in the SNC sony_127_events structure.
Signed-off-by: Almer S. Tigelaar <almer@gnome.org>
Signed-off-by: Mattia Dongili <malattia@linux.it>
Signed-off-by: Len Brown <len.brown@intel.com>
As processor.max_cstate is an init-time-only modparam,
sanity checking it at init-time is sufficient.
http://bugzilla.kernel.org/show_bug.cgi?id=13142
Signed-off-by: Len Brown <len.brown@intel.com>
This toshiba has a touchpad with trackpoint and 2 sets of left
and right buttons (above and below touchpad).
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Linux tells ICH4 users that they can (manually) invoke
"hpet=force" to enable the undocumented ICH-4M HPET.
The HPET becomes available for both clocksource and clockevents.
But as of ff69f2bba6
(acpi: fix of pmtimer overflow that make Cx states time incorrect)
the HPET may be used via clocksource for idle accounting, and
hpet=force on an ICH4 box hangs boot.
It turns out that touching the MMIO HPET withing
the ARB_DIS part of C3 will hang the hardware.
The fix is to simply move the timer access outside
the ARB_DIS region. This is a no-op on modern hardware
because ARB_DIS is no longer used.
http://bugzilla.kernel.org/show_bug.cgi?id=13087
Acked-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Symbols like SOFT_RESET are way too generic to be exported at large.
To avoid this, let's move the mbus bridge register defines into a
separate file and include it where needed. This affects mach-kirkwood,
mach-loki, mach-mv78xx0 and mach-orion5x simultaneously as they all
share code in plat-orion which relies on those defines.
Some other defines have been moved to narrower scopes, or simply deleted
when they had no user.
This fixes compilation problem with mpt2sas on the above listed
platforms.
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Check if we really have Scoop config, otherwice we can get a nice Oops
during probe.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This is causes problems on platforms that have alignment requirements
for DMA transfers.
Signed-off-by: Martin Fuzzey <mfuzzey@gmail.com>
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
In the case where a gadget driver is removed while no
transceiver was found at probe time, a bug in
otg_put_transceiver() will trigger.
Provide symetric calls for otg_get_transceiver() and
otg_put_transceiver(), wherever a transceiver was found or
not.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch to cdc-wdm
- checks for partial extra descriptors
- fixes a leak in the error case of probe
- checks for an exact number of endpoints
- adds a clarifying comment
Signed-off-by: Oliver Neukum <oliver@neukum.org>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This removes tty->low_latency from all USB serial drivers that push
data into the tty layer at hard interrupt context. It's no longer needed
and actually harmful.
Signed-off-by: Oliver Neukum <oliver@neukum.org>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch fixes a problem in sierra_send_setup() function when
composite devices are used. One should not be sending ACM commands to
interfaces that are OBEX. Doing this causes an apparent failure as the
ACM command has to time out before the interface can start being used.
Signed-off-by: Elina Pasheva <epasheva@sierrawireless.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We now have a more correct solution for shrinking runtime driver
footprints than just marking probe() as __init ... use it.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix build error in the MIPS USB IP core family device controller driver.
The driver calls udelay() without including linux/delay.h
Signed-off-by: Matthias Kaehlcke <matthias@kaehlcke.net>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When I want to use my webcam, I get:
vvvvvvv
cheese: page allocation failure. order:5, mode:0x8004
Pid: 8100, comm: cheese Not tainted 2.6.30-rc2-wl-dirty #102
Call Trace:
[<ffffffff802c5d8e>] __alloc_pages_internal+0x3fe/0x520
[<ffffffff80210a20>] dma_generic_alloc_coherent+0x90/0x120
[<ffffffffa001c91e>] hcd_buffer_alloc+0xee/0x130 [usbcore]
[<ffffffffa000d52d>] usb_buffer_alloc+0x2d/0x40 [usbcore]
[<ffffffffa0160e14>] uvc_alloc_urb_buffers+0x84/0x140 [uvcvideo]
[<ffffffffa0160ff6>] uvc_init_video+0x126/0x400 [uvcvideo]
[...]
Oddly, I remembered fixing this and putting in __GFP_NOWARN
because uvcvideo retries a smaller allocation. However, the
allocation function doesn't pass the gfp flags through to
dma_alloc_coherent so we still get the warning!
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1231) fixes a use-after-free bug in g_file_storage. A
device's name may not be available after the device is unregistered,
even if the device structure itself is still allocated. Since
close_backing_file() prints a LUN's name for debugging, it shouldn't
be called after the LUN has been unregistered.
That whole area needed to be cleaned up; the backing files were
getting closed in a couple of different places. The patch fixes
things so that they get closed in just one place, as part of the
unbind procedure, immediately before the LUN is unregistered.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Without this patch, the driver won't check that the last fully-occupied
uframe for a new split transaction was vacant beforehand. This can
lead to a situation in which the first 188 bytes of a 192-byte
isochronous transfer are scheduled in the same uframe as an existing
interrupt transfer. The resulting schedule looks like this:
uframe 0: 188-byte isoc-OUT SSPLIT, 8-byte int-IN SSPLIT
uframe 1: 4-byte isoc-OUT SSPLIT
The SSPLITs are intermingled, causing an error in the downstream hub's
TT.
If you are having problems with devices or hub ports resetting, or failed
interrupt transfers, when you start using a USB audio or video (Isochronous)
device, this patch may help.
Signed-off-by: Dan Streetman <ddstreet@ieee.org>
Reported-by: Kung James <kong1191@gmail.com>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Alan Stern <stern@rowland.harvard.edu>
This patch fixes a problem with any mos7840 device where the use of the field "minor" before it is
initialised results in all the devices being overlaid in memory (minor = 0 for all instances)
Contributed by: Phillip Branch
Signed-off-by: Tony Cook <tony-cook@bigpond.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
add USB ids for the mos7840 based ATEN International serial devices.
Contributed by: Phillip Branch
Signed-off-by: Tony Cook <tony-cook@bigpond.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix this build error when CONFIG_PM is not set:
drivers/usb/musb/musb_core.c:2232: error: 'musb_resume_early' undeclared here
Signed-off-by: Alexander Beregalov <a.beregalov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This email address is going to expire soon and my contribution to musb
is next to zero so remove it.
Signed-off-by: Jarkko Nikula <jarkko.nikula@nokia.com>
Cc: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Bug Fix: high speed detection in LPM mode
Bug Fix: max packet size configuration when switching between HS and FS
Signed-off-by: David Lopo <dlopo@chipidea.mips.com>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Reported by Alessio Treglia on
https://bugs.launchpad.net/ubuntu/+source/linux/+bug/125250
User was getting the following errors in dmesg:
[ 2158.139386] sd 5:0:0:1: ioctl_internal_command return code = 8000002
[ 2158.139390] : Current: sense key: No Sense
[ 2158.139393] Additional sense: No additional sense information
Adds unusual device support.
modified: drivers/usb/storage/unusual_devs.h
Signed-off-by: Chuck Short <zulcss@ubuntu.com>
Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1229) fixes a few lifetime and locking problems in the
usb-serial driver. The main symptom is that an invalid kevent is
created when the serial device is unplugged while a connection is
active.
Ports should be unregistered when device is disconnected,
not when the parent usb_serial structure is deallocated.
Each open file should hold a reference to the corresponding
port structure, and the reference should be released when
the file is closed.
serial->disc_mutex should be acquired in serial_open(), to
resolve the classic race between open and disconnect.
serial_close() doesn't need to hold both serial->disc_mutex
and port->mutex at the same time.
Release the subdriver's module reference only after releasing
all the other references, in case one of the release routines
needs to invoke some code in the subdriver module.
Replace a call to flush_scheduled_work() (which is prone to
deadlocks) with cancel_work_sync(). Also, add a call to
cancel_work_sync() in the disconnect routine.
Reduce the scope of serial->disc_mutex in serial_disconnect().
The only place it really needs to protect is where the
"disconnected" flag is set.
This fixes the bug reported in
http://bugs.freedesktop.org/show_bug.cgi?id=20703
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Dan Williams <dcbw@redhat.com>
Tested-by: Ming Lei <tom.leiming@gmail.com>
Reviewed-by: Oliver Neukum <oliver@neukum.org>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Bugfixes noted by checking the code against the controller
documentation (TI document number SPRUE21):
- Remove declarations for eight non-existent registers (!);
and remove accesses to two of them.
- Remove access to various non-existent bitfields in some of
the registers which *do* exist (those fields must-be-zero).
- Provide comment to replace bogus reset logic (removed above,
it relied on non-existent bitfields). Resets require GPIO
help; this driver doesn't currently know about that.
With some minor cleanup: relocate a comment, avoid an extra
lookup of the PIO timings.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
tape_3590_offline and tape_34xx_offline are removed and tape_generic_offline
is called directly instead.
Signed-off-by: Frank Munzert <munzert@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Linux-2.6.29 deleted the legacy ACPI idle handler, leaving
the CPU_IDLE handler, which does not track bus master activity.
So delete the unused bm_activity field -- it is confusing to
print an always zero value.
This patch could break programs that parse
/proc/acpi/processor/*/power, since it deletes this
line from that file:
bus master activity: 00000000
http://bugzilla.kernel.org/show_bug.cgi?id=13145
is not fixed by this patch, but provoked this patch.
Signed-off-by: Len Brown <len.brown@intel.com>
The c2 and c3 idle handlers check tsc_halts_in_c()
after every time they return from idle. Um, when?:-)
Move this check to init-time to remove the unnecessary
run-time overhead, and also to have the check complete before
the first entry into the idle handler.
ff69f2bba6
(acpi: fix of pmtimer overflow that make Cx states time incorrect)
replaced the hard-coded use of the PM-timer inside idle,
with ktime_get_readl(), which possibly uses the TSC --
so it is now especially prudent to detect a broken TSC
before entering idle.
http://bugzilla.kernel.org/show_bug.cgi?id=13087
Signed-off-by: Len Brown <len.brown@intel.com>
PCIe 1.1 base neither requires the endpoint to implement the entire
PCIe capability structure nor specifies default values of registers
that are not implemented by the device. So we only save and restore
registers that must be implemented by different device types if the
device PCIe capability version is 1.
PCIe 1.1 Capability Structure Expansion ECN and PCIe 2.0 requires
all registers in the PCIe capability to be either implemented or
hardwired to 0. Their PCIe capability version is 2.
Signed-off-by: Yu Zhao <yu.zhao@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Add drivers/pci/*.c source files to DocBook/kernel-api.tmpl
and update those pci/*.c source files that need kernel-doc fixes.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Commit 30a18d6c3f introduced a new
function to set the PCI bus resources. Unfortunately, neither the
author, nor the committers seemed to know that we already have somewhere
to do that -- pcibios_fixup_bus(). This patch moves the hook (used only
by the K8 code) into x86-specific code where it should have been in the
first place.
Cc: Yinghai Lu <yinghai.lu@sun.com>
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Without this patch, Broadcom BCM5906 Ethernet controllers set up via MSI
cause the machine to hang. Tejun agreed that the best is to blacklist
the whole chipset and after adding it, seeing the other VIA quirks
disabling MSI, this very much looks like the right way.
Cc: <stable@kernel.org>
Signed-off-by: Thomas Renninger <trenn@suse.de>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
commit 7a192ec334 ("platform driver: fix
incorrect use of 'platform_bus_type' with 'struct device_driver') turned a
driver_UNregister into platform_driver_REGISTER. Correct this to
platform_driver_UNregister.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
On Tuesday 14 April 2009 20:31:21 Subrata Modak wrote:
> Observed the following build error:
> ---
> CC drivers/macintosh/mediabay.o
> In file included from drivers/macintosh/mediabay.c:21:
> include/linux/ide.h:605: error: field ‘request_sense_rq’ has incomplete
> type
> make[2]: *** [drivers/macintosh/mediabay.o] Error 1
> make[1]: *** [drivers/macintosh] Error 2
> make: *** [drivers] Error 2
> ---
mediabay shouldn't include <linux/ide.h> unconditionally so
remove the superfluous include from mediabay.c (<asm/mediabay.h>
will pull <linux/ide.h> in for CONFIG_BLK_DEV_IDE_PMAC=y).
Reported-by: Subrata Modak <subrata@linux.vnet.ibm.com>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
My laptop (Acer Travelmate 660) always cuts the power when rebooting
which causes the disk to emergency-park it's head.
Add a dmi check to stop disk as for shutdown on this laptop.
Signed-off-by: Bruno Prémont <bonbons@linux-vserver.org>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
With 2.6.30-rc2 I face a kernel crash on the 32bit hppa architecture
due to ide-cd when udev creates the device nodes at startup:
Kernel Fault: Code=26 regs=8ed34c40 (Addr=00000024)
IASQ: 00000000 00000000 IAOQ: 1034b5ac 1034b5b0
IIR: 4ab30048 ISR: 00000000 IOR: 00000024
CPU: 0 CR30: 8ed34000 CR31: ffff55ff
ORIG_R28: 00000000
IAOQ[0]: ide_complete_rq+0x2c/0x70
IAOQ[1]: ide_complete_rq+0x30/0x70
RP(r2): cdrom_newpc_intr+0x178/0x46c
Backtrace:
[<1035c608>] cdrom_newpc_intr+0x178/0x46c
[<1034c494>] ide_intr+0x1b0/0x214
[<1016d284>] handle_IRQ_event+0x70/0x150
[<1016d4b0>] __do_IRQ+0x14c/0x1cc
[<102f7864>] superio_interrupt+0x88/0xbc
[<1016d284>] handle_IRQ_event+0x70/0x150
[<1016d4b0>] __do_IRQ+0x14c/0x1cc
[<10112efc>] do_cpu_irq_mask+0x9c/0xd0
[<10116068>] intr_return+0x0/0x4
This crash seems to happen due to an uninitialized variable "rc".
The compiler even warns about that:
CC drivers/ide/ide-cd.o
/mnt/sda4/home/cvs/parisc/git-kernel/linus-linux-2.6/drivers/ide/ide-cd.c: In function `cdrom_newpc_intr':
/mnt/sda4/home/cvs/parisc/git-kernel/linus-linux-2.6/drivers/ide/ide-cd.c:612: warning: `rc' might be used uninitialized in this function
After applying the trivial patch below, which just initializes
the variable to zero, the kernel doesn't crash any longer:
Starting the hotplug events dispatcher: udevd.
Synthesizing the initial hotplug events...
hda: command error: status=0x51 { DriveReady SeekComplete Error }
hda: command error: error=0x54 <3>{ AbortedCommand LastFailedSense=0x05 }
ide: failed opcode was: unknown
done.
Signed-off-by: Helge Deller <deller@gmx.de>
Acked-by: Borislav Petkov <petkovbb@gmail.com>
Cc: Linus <torvalds@linux-foundation.org>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Fix UDMA throughput bug: tCYC averages t2CYCTYP/2, but the code
previously assumed it was the same as t2CYCTYP. (That is, it was
using just one clock edge, not both.) Move the table's type
declaration so it's adjacent to the table, making it more clear
what those numbers mean.
On one system this change increased throughput by almost 4x: UDMA/66
sometimes topped 23 MB/sec (on a drive known to do much better). On
another system it was around a 10% win (UDMA/66 up to 7+ MB/sec).
The difference might be caused by the ratio between memory and IDE
clocks. In the system with large speedup, this was exactly 2 (as a
workaround for a rev 1.1 silicon bug). The other system used a more
standard ratio of 1.63 (and rev 2.1 silicon) ... clock domain synch
might have some issues, they're not unheard-of.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
If using the UCC on a MPC8360 in RMII mode, don;t set
UCC_GETH_UPSMR_RPM bit in the upsmr register.
Signed-off-by: Heiko Schocher <hs@denx.de>
Acked-by: Li Yang <leoli@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While ifconfig eth0 up kernel calls open() of 8139 driver(8139too.c).
In rtl8139_hw_start() of rtl8139_open(), 8139 driver enable RX before
setting up the DMA buffer address. In this interval where RX was
enabled and DMA buffer address is not yet set up, any incoming
broadcast packet would be send to a strange physical address:
0x003e8800 which is the default value of DMA buffer address.
Unfortunately, this address is used by Linux kernel. So kernel panics.
This patch fix it by setting up DMA buffer address before RX enabled
and everything is fine even under broadcast packets attack.
Signed-off-by: Jonathan Lin <jon.lin@vatics.com>
Signed-off-by: Amos Kong <jianjun@zeuux.org>
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that the powermac IDE host driver can be modular, we need to
export check_media_bay_by_base() and media_bay_set_ide_infos()
from drivers/macintosh/mediabay.c for it.
This fixes the following build error:
> CC [M] drivers/ide/pmac.o
> drivers/ide/pmac.c: In function ‘pmac_ide_init_dev’:
> drivers/ide/pmac.c:955: error: implicit declaration of function
> ‘check_media_bay_by_base’
> drivers/ide/pmac.c: In function ‘pmac_ide_setup_device’:
> drivers/ide/pmac.c:1090: error: implicit declaration of function
> ‘media_bay_set_ide_infos’
> make[2]: *** [drivers/ide/pmac.o] Error 1
> make[1]: *** [drivers/ide] Error 2
> make: *** [drivers] Error 2
Reported-by: Subrata Modak <subrata@linux.vnet.ibm.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Fixes this build error:
In file included from drivers/macintosh/mediabay.c:21:
include/linux/ide.h:605: error: field 'request_sense_rq' has incomplete type
Signed-off-by: Alexander Beregalov <a.beregalov@gmail.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
There is currently only one way for userspace to say "wait for my storage
device to get ready for the modules I just loaded": to load the
scsi_wait_scan module. Expectations of userspace are that once this
module is loaded, all the (storage) devices for which the drivers
were loaded before the module load are present.
Now, there are some issues with the implementation, and the async
stuff got caught in the middle of this: The existing code only
waits for the scsy async probing to finish, but it did not take
into account at all that probing might not have begun yet.
(Russell ran into this problem on his computer and the fix works for him)
This patch fixes this more thoroughly than the previous "fix", which
had some bad side effects (namely, for kernel code that wanted to wait for
the scsi scan it would also do an async sync, which would deadlock if you did
it from async context already.. there's a report about that on lkml):
The patch makes the module first wait for all device driver probes, and then it
will wait for the scsi parallel scan to finish.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Tested-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit 201361a5 introduces a leak when unwinding on error. Reorder
unwind, and eliminate leak.
Cc: Eric Anholt <eric@anholt.net>
Cc: Keith Packard <keithp@keithp.com>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
[anholt: fixed uninit variable use introduced in original patch]
Signed-off-by: Eric Anholt <eric@anholt.net>
This had been delayed for some time due to failure to work on the one piece
of G41 hardware we had, and lack of success reports from anybody else.
Current hardware appears to be OK.
Signed-off-by: Zhenyu Wang <zhenyu.z.wang@intel.com>
[anholt: hand-applied due to conflicts with IGD patches]
Signed-off-by: Eric Anholt <eric@anholt.net>
In error paths where a CQ is not created, pbl is not freeed properly.
In nes_destroy_cq(), add the corresponding check for nescq->mcrqf to
not call nes_free_resource() when it is already done in nes_create_cq().
Signed-off-by: Miroslaw Walukiewicz <miroslaw.walukiewicz@intel.com>
Signed-off-by: Chien Tung <chien.tin.tung@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Boaz Harrosh
Dan Carpenter
Eric Moore
Dave Hansen
Brian King
Joe Eykholt
Robert Love
Chris Leech
Abhijeet Joglekar
kxie@chelsio.com
Mike Christie
Christof Schmitt
Martin Petermann
Swen Schillig
Martin Petermann
James Smart
FUJITA Tomonori
Peter Jones
Tilman Schmidt
Waskiewicz Jr, Peter P
Stephen Hemminger
Ayaz Abdulla
Yevgeny Petrilin
Adrian McMenamin
Dmitry Torokhov
Russell King
Christian Borntraeger
Linus Torvalds
Alan Cox
Niels de Vos
Len Brown
Sage Weil
Ben Skeggs
Jonas Bonn
Dave Airlie
Maciej Cencora
Matthew Garrett
Lin Ming
Mattia Dongili
Almer S. Tigelaar
Nicolas Pitre
Dmitry Baryshkov
Martin Fuzzey
Robert Jarzmik
Oliver Neukum
Elina Pasheva
David Brownell
Matthias Kaehlcke
Johannes Berg
Alan Stern
Dan Streetman
Tony Cook
Alexander Beregalov
Jarkko Nikula
David Lopo
Chuck Short
Bartlomiej Zolnierkiewicz
Ladislav Michl
Frank Munzert
Yu Zhao
Randy Dunlap
Yinghai Lu
Matthew Wilcox
Thomas Renninger
Geert Uytterhoeven
Bruno Prémont
Helge Deller
Heiko Schocher
Jianjun kong
Arjan van de Ven
Chris Wright
Wu Fengguang
Zhenyu Wang
Miroslaw Walukiewicz