Fixes the following sparse warning:
kernel/irq/chip.c:786:1: warning:
symbol '__irq_do_set_handler' was not declared. Should it be static?
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Link: http://lkml.kernel.org/r/1474817799-18676-1-git-send-email-weiyj.lk@gmail.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
There is no point in trying to configure the trigger of a chained
interrupt if no trigger information has been configured. At best
this is ignored, and at the worse this confuses the underlying
irqchip (which is likely not to handle such a thing), and
unnecessarily alarms the user.
Only apply the configuration if type is not IRQ_TYPE_NONE.
Fixes: 1e12c4a939 ("genirq: Correctly configure the trigger on chained interrupts")
Reported-and-tested-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Link: https://lkml.kernel.org/r/CAMuHMdVW1eTn20=EtYcJ8hkVwohaSuH_yQXrY2MGBEvZ8fpFOg@mail.gmail.com
Link: http://lkml.kernel.org/r/1474274967-15984-1-git-send-email-marc.zyngier@arm.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The current irq spreading infrastructure is just looking at a cpumask and
tries to spread the interrupts over the mask. Thats suboptimal as it does
not take numa nodes into account.
Change the logic so the interrupts are spread across numa nodes and inside
the nodes. If there are more cpus than vectors per node, then we set the
affinity to several cpus. If HT siblings are available we take that into
account and try to set all siblings to a single vector.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Christoph Hellwig <hch@lst.de>
Cc: axboe@fb.com
Cc: keith.busch@intel.com
Cc: agordeev@redhat.com
Cc: linux-block@vger.kernel.org
Link: http://lkml.kernel.org/r/1473862739-15032-3-git-send-email-hch@lst.de
For irq spreading want to store affinity masks in the msi_entry. Add the
infrastructure for it.
We allocate an array of cpumasks with an array size of the number of used
vectors in the entry, so we can hand in the information per linux interrupt
later.
As we hand in the number of used vectors, we assign them right
away. Convert all the call sites.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: axboe@fb.com
Cc: keith.busch@intel.com
Cc: agordeev@redhat.com
Cc: linux-block@vger.kernel.org
Cc: Christoph Hellwig <hch@lst.de>
Link: http://lkml.kernel.org/r/1473862739-15032-2-git-send-email-hch@lst.de
- ACPI IORT core code
- IORT support for the GICv3 ITS
- A few of GIC cleanups
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=Xhg0
-----END PGP SIGNATURE-----
Merge tag 'irqchip-4.9-1' of git://git.kernel.org/pub/scm/linux/kernel/git/maz/arm-platforms into irq/core
Merge the first drop of irqchip updates for 4.9 from Marc Zyngier:
- ACPI IORT core code
- IORT support for the GICv3 ITS
- A few of GIC cleanups
Information about interrupts is exposed via /proc/interrupts, but the
format of that file has changed over kernel versions and differs across
architectures. It also has varying column numbers depending on hardware.
That all makes it hard for tools to parse.
To solve this, expose the information through sysfs so each irq attribute
is in a separate file in a consistent, machine parsable way.
This feature is only available when both CONFIG_SPARSE_IRQ and
CONFIG_SYSFS are enabled.
Examples:
/sys/kernel/irq/18/actions: i801_smbus,ehci_hcd:usb1,uhci_hcd:usb7
/sys/kernel/irq/18/chip_name: IR-IO-APIC
/sys/kernel/irq/18/hwirq: 18
/sys/kernel/irq/18/name: fasteoi
/sys/kernel/irq/18/per_cpu_count: 0,0
/sys/kernel/irq/18/type: level
/sys/kernel/irq/25/actions: ahci0
/sys/kernel/irq/25/chip_name: IR-PCI-MSI
/sys/kernel/irq/25/hwirq: 512000
/sys/kernel/irq/25/name: edge
/sys/kernel/irq/25/per_cpu_count: 29036,0
/sys/kernel/irq/25/type: edge
[ tglx: Moved kobject_del() under sparse_irq_lock, massaged code comments
and changelog ]
Signed-off-by: Craig Gallek <kraig@google.com>
Cc: David Decotigny <decot@google.com>
Link: http://lkml.kernel.org/r/1473783291-122873-1-git-send-email-kraigatgoog@gmail.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Some callers of __irq_set_trigger() masks all flags except trigger mode
flags. This is unnecessary, ase __irq_set_trigger() already does this
before usage of flags.
[ tglx: Moved the flag mask and adjusted comment. Removed the hunk in
enable_percpu_irq() as it is required there ]
Signed-off-by: Alexander Kuleshov <kuleshovmail@gmail.com>
Link: http://lkml.kernel.org/r/20160719095408.13778-1-kuleshovmail@gmail.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Commit 1bf4ddc46c ("irqdomain: Introduce irq_domain_create_{linear,
tree}") introduced the use of fwnode_handle to identify the interrupt
controller when calling __irq_domain_add but missed updating the kernel
doc parameters for the function.
Update this comment. While we are touching this code, also consolidate
the declaration and assignment of of_node.
Signed-off-by: Punit Agrawal <punit.agrawal@arm.com>
Acked-by: Marc Zygnier <marc.zyngier@arm.com>
Link: http://lkml.kernel.org/r/1464699409-23113-1-git-send-email-punit.agrawal@arm.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Most (if not all) code here implicitly assumes that the maximum number of
IRQs per chip will be 32, and thus uses 'u32' or 'unsigned long' for many
tasks (for example "struct irq_data" declares its 'mask' field as 'u32',
and "struct irq_chip_generic" declares its 'installed' field as 'unsigned
long')
However, there is no check to verify that irqs_per_chip is <= 32. Hence,
calling irq_alloc_domain_generic_chips() with a bigger value will result in
unexpected results.
Provide a wrapper with a MAYBE_BUILD_BUG_ON(nrirqs >= 32) to catch such
cases.
[ tglx: Reduced changelog to the essential information ]
Signed-off-by: Sebastian Frias <sf84@laposte.net>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Mason <slash.tmp@free.fr>
Cc: Jason Cooper <jason@lakedaemon.net>
Link: http://lkml.kernel.org/r/57B31D94.5040701@laposte.net
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
According to the xlate() callback definition, the 'out_type' parameter
needs to be the "linux irq type".
A mask for such bits exists, IRQ_TYPE_SENSE_MASK, which is correctly
applied in irq_domain_xlate_twocell()
So use it for irq_domain_xlate_onetwocell() as well.
Signed-off-by: Sebastian Frias <sf84@laposte.net>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Mason <slash.tmp@free.fr>
Cc: Jason Cooper <jason@lakedaemon.net>
Link: http://lkml.kernel.org/r/57A05F5D.103@laposte.net
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Without this patch irq_domain_disassociate() cannot properly release the
interrupt. In fact, irq_map_generic_chip() checks a bit on 'gc->installed'
but said bit is never cleared, only set.
Commit 088f40b7b0 ("genirq: Generic chip: Add linear irq domain support")
added irq_map_generic_chip() function and also stated "This lacks a removal
function for now".
This commit provides an implementation of an unmap function that can be
called by irq_domain_disassociate().
[ tglx: Made the function static and removed the export as we have neither
a prototype nor a modular user. ]
Fixes: 088f40b7b0 ("genirq: Generic chip: Add linear irq domain support")
Signed-off-by: Sebastian Frias <sf84@laposte.net>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Mason <slash.tmp@free.fr>
Cc: Jason Cooper <jason@lakedaemon.net>
Link: http://lkml.kernel.org/r/579F5C5A.2070507@laposte.net
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
irq_map_generic_chip() contains about the same code as
irq_get_domain_generic_chip() except for the return values.
Split out the irq_get_domain_generic_chip() implementation so it can be
reused.
[ tglx: Removed the extra churn in irq_get_domain_generic_chip() callers
and massaged changelog ]
Signed-off-by: Sebastian Frias <sf84@laposte.net>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Mason <slash.tmp@free.fr>
Cc: Jason Cooper <jason@lakedaemon.net>
Link: http://lkml.kernel.org/r/579F5C69.8070006@laposte.net
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The percpu_devid handler is not robust against spurious interrupts. If a
spurious interrupt happens and no action is installed then the handler
crashes with a NULL pointer dereference.
Add a sanity check for this and log the wreckage once in dmesg.
Reported-by: Majun <majun258@huawei.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: guohanjun@huawei.com
Cc: dingtianhong@huawei.com
Cc: linux-arm-kernel@lists.infradead.org
Link: http://lkml.kernel.org/r/alpine.DEB.2.20.1609021436160.5647@nanos
Without locking out CPU mask operations we might end up with an inconsistent
view of the cpumask in the function.
Fixes: 5e385a6ef31f: "genirq: Add a helper to spread an affinity mask for MSI/MSI-X vectors"
Signed-off-by: Christoph Hellwig <hch@lst.de>
Link: http://lkml.kernel.org/r/1470924405-25728-1-git-send-email-hch@lst.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Obviously we should free action here if irq_chip_pm_get failed.
Fixes: be45beb2df69: "genirq: Add runtime power management support for IRQ chips"
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Cc: Jon Hunter <jonathanh@nvidia.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Link: http://lkml.kernel.org/r/1471854112-13006-1-git-send-email-shawn.lin@rock-chips.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Commit 1e2a7d7849 ("irqdomain: Don't set type when mapping an IRQ")
moved the trigger configuration call from the irqdomain mapping to
the interrupt being actually requested.
This patch failed to handle the case where we configure a chained
interrupt, which doesn't get requested through the usual path.
In order to solve this, let's call __irq_set_trigger just before
starting the cascade interrupt. Special care must be taken to
make the flow handler stick, as the .irq_set_type method could
have reset it (it doesn't know we're dealing with a chained
interrupt).
Based on an initial patch by Jon Hunter.
Fixes: 1e2a7d7849 ("irqdomain: Don't set type when mapping an IRQ")
Reported-by: John Stultz <john.stultz@linaro.org>
Reported-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: John Stultz <john.stultz@linaro.org>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Bharat Kumar Gogada reported issues with the generic MSI code, where the
end-point ended up with garbage in its MSI configuration (both for the vector
and the message).
It turns out that the two MSI paths in the kernel are doing slightly different
things:
generic MSI: disable MSI -> allocate MSI -> enable MSI -> setup EP
PCI MSI: disable MSI -> allocate MSI -> setup EP -> enable MSI
And it turns out that end-points are allowed to latch the content of the MSI
configuration registers as soon as MSIs are enabled. In Bharat's case, the
end-point ends up using whatever was there already, which is not what you
want.
In order to make things converge, we introduce a new MSI domain flag
(MSI_FLAG_ACTIVATE_EARLY) that is unconditionally set for PCI/MSI. When set,
this flag forces the programming of the end-point as soon as the MSIs are
allocated.
A consequence of this is that we have an extra activate in irq_startup, but
that should be without much consequence.
tglx:
- Several people reported a VMWare regression with PCI/MSI-X passthrough. It
turns out that the patch also cures that issue.
- We need to have a look at the MSI disable interrupt path, where we write
the msg to all zeros without disabling MSI in the PCI device. Is that
correct?
Fixes: 52f518a3a7 "x86/MSI: Use hierarchical irqdomains to manage MSI interrupts"
Reported-and-tested-by: Bharat Kumar Gogada <bharat.kumar.gogada@xilinx.com>
Reported-and-tested-by: Foster Snowhill <forst@forstwoof.ru>
Reported-by: Matthias Prager <linux@matthiasprager.de>
Reported-by: Jason Taylor <jason.taylor@simplivity.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: linux-pci@vger.kernel.org
Cc: stable@vger.kernel.org
Link: http://lkml.kernel.org/r/1468426713-31431-1-git-send-email-marc.zyngier@arm.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The new affinity hint argument of __irq_domain_alloc_irqs() is missing in
irq_reserve_ipi(). Add it.
This fixes the following compilation error:
kernel/irq/ipi.c: In function ‘irq_reserve_ipi’:
kernel/irq/ipi.c:85:9: error: too few arguments to function ‘__irq_domain_alloc_irqs’
virq = __irq_domain_alloc_irqs(domain, virq, nr_irqs, NUMA_NO_NODE,
^
Fixes: 06ee6d571f ("genirq: Add affinity hint to irq allocation")
Signed-off-by: Vincent Stehlé <vincent.stehle@laposte.net>
Cc: linux-pci@vger.kernel.org
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
If an irq_domain is auto-recursive and irq_domain_alloc_irqs_recursive()
for its parent has returned an error, then do return and avoid calling
irq_domain_free_irqs_recursive() uselessly, because:
- if domain->ops->alloc() had failed for an auto-recursive irq_domain,
then irq_domain_free_irqs_recursive() had already been called;
- if domain->ops->alloc() had failed for a not auto-recursive irq_domain,
then there is nothing to free at all.
Signed-off-by: Alexander Popov <alex.popov@linux.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Link: http://lkml.kernel.org/r/1467505448-2850-1-git-send-email-alex.popov@linux.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
virq is not required to be the same for all msi descs. Use the base irq number
from the desc in the debug printk.
Reported-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Use the affinity hint in the irqdesc allocator. The hint is used to determine
the node for the allocation and to set the affinity of the interrupt.
If multiple interrupts are allocated (multi-MSI) then the allocator iterates
over the cpumask and for each set cpu it allocates on their node and sets the
initial affinity to that cpu.
If a single interrupt is allocated (MSI-X) then the allocator uses the first
cpu in the mask to compute the allocation node and uses the mask for the
initial affinity setting.
Interrupts set up this way are marked with the AFFINITY_MANAGED flag to
prevent userspace from messing with their affinity settings.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Christoph Hellwig <hch@lst.de>
Cc: linux-block@vger.kernel.org
Cc: linux-pci@vger.kernel.org
Cc: linux-nvme@lists.infradead.org
Cc: axboe@fb.com
Cc: agordeev@redhat.com
Link: http://lkml.kernel.org/r/1467621574-8277-5-git-send-email-hch@lst.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The function irq_create_of_mapping() is used to create an interrupt
mapping. However, depending on whether the irqdomain, to which the
interrupt belongs, is part of a hierarchy, determines whether the
mapping is created via calling irq_domain_alloc_irqs() or
irq_create_mapping().
To dispose of the interrupt mapping, drivers call irq_dispose_mapping().
However, this function does not check to see if the irqdomain is part
of a hierarchy or not and simply assumes that it was mapped via calling
irq_create_mapping() so calls irq_domain_disassociate() to unmap the
interrupt.
Fix this by checking to see if the irqdomain is part of a hierarchy and
if so call irq_domain_free_irqs() to free/unmap the interrupt.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
Link: http://lkml.kernel.org/r/1466501002-16368-1-git-send-email-jonathanh@nvidia.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This adds a software irq handler for controllers that multiplex
interrupts from multiple devices, but don't know which device generated
the interrupt. For these devices, the irq handler that demuxes must
check every action for every software irq using the same h/w irq in order
to find out which device generated the interrupt. This will inevitably
trigger spurious interrupt detection if we are noting the irq.
The new irq handler does not track the handling for spurious interrupt
detection. An irq that uses this also won't get stats tracked since it
didn't generate the interrupt, nor added to randomness since they are
not random.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: linux-pci@vger.kernel.org
Cc: Jon Derrick <jonathan.derrick@intel.com>
Link: http://lkml.kernel.org/r/1466200821-29159-1-git-send-email-keith.busch@intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
- Fix a few bugs in configuring the default trigger from the irqdomain layer
- Make the genirq layer PM aware
- Add PM capability to the ARM GIC driver
- Add support for 2-level translation tables to the GICv3 ITS driver
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=OnlS
-----END PGP SIGNATURE-----
Merge tag 'irqchip-for-4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/maz/arm-platforms into irq/core
First drop of irqchip updates for 4.8 from Marc Zyngier:
- Fix a few bugs in configuring the default trigger from the irqdomain layer
- Make the genirq layer PM aware
- Add PM capability to the ARM GIC driver
- Add support for 2-level translation tables to the GICv3 ITS driver
Some IRQ chips may be located in a power domain outside of the CPU
subsystem and hence will require device specific runtime power
management. In order to support such IRQ chips, add a pointer for a
device structure to the irq_chip structure, and if this pointer is
populated by the IRQ chip driver and CONFIG_PM is selected in the kernel
configuration, then the pm_runtime_get/put APIs for this chip will be
called when an IRQ is requested/freed, respectively.
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Some IRQ chips, such as GPIO controllers or secondary level interrupt
controllers, may require require additional runtime power management
control to ensure they are accessible. For such IRQ chips, it makes sense
to enable the IRQ chip when interrupts are requested and disabled them
again once all interrupts have been freed.
When mapping an IRQ, the IRQ type settings are read and then programmed.
The mapping of the IRQ happens before the IRQ is requested and so the
programming of the type settings occurs before the IRQ is requested. This
is a problem for IRQ chips that require additional power management
control because they may not be accessible yet. Therefore, when mapping
the IRQ, don't program the type settings, just save them and then program
these saved settings when the IRQ is requested (so long as if they are not
overridden via the call to request the IRQ).
Add a stub function for irq_domain_free_irqs() to avoid any compilation
errors when CONFIG_IRQ_DOMAIN_HIERARCHY is not selected.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
As we now do for non-percpu interrupt, perform a lookup of the
interrupt trigger if the user doesn't supply one. The difference
here is that we can only do it at enable time (trigger configuration
can be per-cpu as well).
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
For some devices the IRQ trigger type for a device is read from
firmware, such as device-tree. The IRQ trigger type is typically read
when the mapping for IRQ is created, which is before the IRQ is
requested. Hence, the IRQ trigger type is programmed when mapping the
IRQ and not when requesting the IRQ.
Although this works for most cases, in order to support IRQ chips which
require runtime power management, which may not be accessible prior
to requesting the IRQ, it is desirable to look-up the IRQ trigger type
when it is requested. Therefore, if the IRQ trigger type is not
specified when __setup_irq() is called, look-up the saved IRQ trigger
type. This will allow us to defer the programming of the trigger type
from when the IRQ is mapped to when it is actually requested.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
When mapping an IRQ, it is possible that a mapping for the IRQ already
exists. If mapping does exist then there are the following issues with
regard to the handling of the IRQ type settings ...
1. If the domain is part of a hierarchy, then:
a. We do not check that the type settings for the existing mapping
match those of the new mapping.
b. We do not check to see if the type settings have been programmed
yet (and they might not have been) and so we may never set the
type.
2. If the domain is NOT part of a hierarchy, we will overwrite the
current type settings programmed if they are different from the
previous mapping. Please note that irq_create_mapping()
calls irq_find_mapping() to check if a mapping already exists.
Although, it may be unlikely that the type settings for a shared
interrupt would not match, nonetheless we should check for this.
Therefore, to fix this check if a mapping exists (regardless of whether
the domain is part of a hierarchy or not) and if it does then:
1. Return the IRQ number if the type settings match or are not
specified.
2. Program the type settings and return the IRQ number if the type
settings have not been programmed yet.
3. Otherwise if the type setting do not match, then print a warning
and don't return the IRQ number.
Furthermore, add a warning if the type return by irq_domain_translate()
has bits outside the sense mask set and then clear these bits. If these
bits are not cleared then this will cause the comparision of the type
settings for an existing mapping to fail with that of the new mapping
even if the sense bit themselves match. The reason being is that the
existing type settings are read by calling irq_get_trigger_type() which
will clear any bits outside the sense mask. This will allow us to detect
irqchips that are not correctly clearing these bits and fix them.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
sprintf() and snprintf() implementation of kernel guarantees that
its result is terminated with null byte if size is larger than 0. So we
don't need to call memset() at all.
Signed-off-by: Weongyo Jeong <weongyo.linux@gmail.com>
Link: http://lkml.kernel.org/r/1459451703-5744-1-git-send-email-weongyo.linux@gmail.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
- A number of embarassing buglets (GICv3, PIC32)
- A more substential errata workaround for Cavium's GICv3 ITS
(kept for post-rc1 due to its dependency on NUMA)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=E+j+
-----END PGP SIGNATURE-----
Merge tag 'irqchip-4.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/maz/arm-platforms into irq/urgent
Merge irqchip updates from Marc Zyngier:
- A number of embarassing buglets (GICv3, PIC32)
- A more substential errata workaround for Cavium's GICv3 ITS
(kept for post-rc1 due to its dependency on NUMA)
Commit 7cec18a390 changed the return type of irq_destroy_ipi to int, but
missed adding a value to one return statement. Fix this to silence the
resulting compiler warning:
kernel/irq/ipi.c In function ‘irq_destroy_ipi’:
kernel/irq/ipi.c:128:3: warning: ‘return’ with no value, in function returning non-void [-Wreturn-type]
Fixes: 7cec18a390 "genirq: Add error code reporting to irq_{reserve,destroy}_ipi"
Signed-off-by: Matt Redfearn <matt.redfearn@imgtec.com>
Cc: linux-mips@linux-mips.org
Link: http://lkml.kernel.org/r/1464086550-24734-1-git-send-email-matt.redfearn@imgtec.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Commit e614523653 ("radix_tree: add support for multi-order entries")
left the impression that the support for multiorder radix tree entries
was functional. As soon as Ross tried to use it, it became apparent
that my testing was completely inadequate, and it didn't even work a
little bit for orders that were not a multiple of shift.
This series of patches is the result of about 6 weeks of redesign,
reimplementation, testing, arguing and hair-pulling. The great news is
that the test-suite is now far better than it was. That's reflected in
the diffstat for the test-suite alone:
12 files changed, 436 insertions(+), 28 deletions(-)
The highlight for users of the tree is that the restriction on the order
of inserted entries being >= RADIX_TREE_MAP_SHIFT is now gone; the radix
tree now supports any order between 0 and 64.
For those who are interested in how the tree works, patch 9 is probably
the most interesting one as it introduces the new machinery for handling
sibling entries.
I've tried to be fair in attributing authorship to the person who
contributed the majority of the code in each patch; Ross has been an
invaluable partner in the development of this support and it's fair to
say that each of us has code in every commit.
I should also express my appreciation of the 0day testing. It prompted
me that I was bloating the tinyconfig in an unacceptable way, and it
bisected to a commit which contained a rather nasty memory-corruption
bug.
This patch (of 29):
The irqdomain code was checking for 0 or 1 entries, not 0 entries like
the comment said they were. Introduce a new helper that will actually
check for an empty tree.
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Reviewed-by: Ross Zwisler <ross.zwisler@linux.intel.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Cc: Konstantin Khlebnikov <koct9i@gmail.com>
Cc: Kirill Shutemov <kirill.shutemov@linux.intel.com>
Cc: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Core infrastructural changes:
- Support for natively single-ended GPIO driver stages. This
means that if the hardware has registers to configure open
drain or open source configuration, we use that rather than
(as we did before) try to emulate it by switching the line
to an input to get high impedance. This is also documented
throughly in Documentation/gpio/driver.txt for those of you
who did not understand one word of what I just wrote.
- Start to do away with the unnecessarily complex and
unitelligible ARCH_REQUIRE_GPIOLIB and
ARCH_WANT_OPTIONAL_GPIOLIB, another evolutional artifact from
the time when the GPIO subsystem was unmaintained. Archs can
now just select GPIOLIB and be done with it, cleanups to
arches will trickle in for the next kernel. Some minor archs
ACKed the changes immediately so these are included in this
pull request.
- Advancing the use of the data pointer inside the GPIO device
for storing driver data by switching the PowerPC, Super-H
Unicore and a few other subarches or subsystem drivers in
ALSA SoC, Input, serial, SSB, staging etc to use it.
- The initialization now reads the input/output state of the
GPIO lines, so that each GPIO descriptor knows - if this
callback is implemented - whether the line is input or
output. This also reflects nicely in userspace "lsgpio".
- It is now possible to name GPIO producer names, line names,
from the device tree. (Platform data has been supported for
a while.) I bet we will get a similar mechanism for ACPI
one of those days. This makes is possible to get sensible
producer names for e.g. GPIO rails in "lsgpio" in userspace.
New drivers:
- New driver for the Loongson1.
- The XLP driver now supports Broadcom Vulcan ARM64.
- The IT87 driver now supports IT8620 and IT8628.
- The PCA953X driver now supports Galileo Gen2.
Driver improvements:
- MCP23S08 was switched to use the gpiolib irqchip helpers and
now also suppors level-triggered interrupts.
- 74x164 and RCAR now supports the .set_multiple() callback
- AMDPT was converted to use generic GPIO.
- TC3589x, TPS65218, SX150X, F7188X, MENZ127, VX855, WM831X, WM8994
support the new single ended callback for open drain
and in some cases open source.
- Implement the .get_direction() callback for a few more drivers
like PL061, Xgene.
Cleanups:
- Paul Gortmaker combed through the drivers and de-modularized
those who are not really modules.
- Move the GPIO poweroff DT bindings to the power subdir where
they belong.
- Rename gpio-generic.c to gpio-mmio.c, which is much more to the
point. That's what it is handling, nothing more, nothing less.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=z4d6
-----END PGP SIGNATURE-----
Merge tag 'gpio-v4.7-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO updates from Linus Walleij:
"This is the bulk of GPIO changes for kernel cycle v4.7:
Core infrastructural changes:
- Support for natively single-ended GPIO driver stages.
This means that if the hardware has registers to configure open
drain or open source configuration, we use that rather than (as we
did before) try to emulate it by switching the line to an input to
get high impedance.
This is also documented throughly in Documentation/gpio/driver.txt
for those of you who did not understand one word of what I just
wrote.
- Start to do away with the unnecessarily complex and unitelligible
ARCH_REQUIRE_GPIOLIB and ARCH_WANT_OPTIONAL_GPIOLIB, another
evolutional artifact from the time when the GPIO subsystem was
unmaintained.
Archs can now just select GPIOLIB and be done with it, cleanups to
arches will trickle in for the next kernel. Some minor archs ACKed
the changes immediately so these are included in this pull request.
- Advancing the use of the data pointer inside the GPIO device for
storing driver data by switching the PowerPC, Super-H Unicore and
a few other subarches or subsystem drivers in ALSA SoC, Input,
serial, SSB, staging etc to use it.
- The initialization now reads the input/output state of the GPIO
lines, so that each GPIO descriptor knows - if this callback is
implemented - whether the line is input or output. This also
reflects nicely in userspace "lsgpio".
- It is now possible to name GPIO producer names, line names, from
the device tree. (Platform data has been supported for a while).
I bet we will get a similar mechanism for ACPI one of those days.
This makes is possible to get sensible producer names for e.g.
GPIO rails in "lsgpio" in userspace.
New drivers:
- New driver for the Loongson1.
- The XLP driver now supports Broadcom Vulcan ARM64.
- The IT87 driver now supports IT8620 and IT8628.
- The PCA953X driver now supports Galileo Gen2.
Driver improvements:
- MCP23S08 was switched to use the gpiolib irqchip helpers and now
also suppors level-triggered interrupts.
- 74x164 and RCAR now supports the .set_multiple() callback
- AMDPT was converted to use generic GPIO.
- TC3589x, TPS65218, SX150X, F7188X, MENZ127, VX855, WM831X, WM8994
support the new single ended callback for open drain and in some
cases open source.
- Implement the .get_direction() callback for a few more drivers like
PL061, Xgene.
Cleanups:
- Paul Gortmaker combed through the drivers and de-modularized those
who are not really modules.
- Move the GPIO poweroff DT bindings to the power subdir where they
belong.
- Rename gpio-generic.c to gpio-mmio.c, which is much more to the
point. That's what it is handling, nothing more, nothing less"
* tag 'gpio-v4.7-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (126 commits)
MIPS: do away with ARCH_[WANT_OPTIONAL|REQUIRE]_GPIOLIB
gpio: zevio: make it explicitly non-modular
gpio: timberdale: make it explicitly non-modular
gpio: stmpe: make it explicitly non-modular
gpio: sodaville: make it explicitly non-modular
pinctrl: sh-pfc: Let gpio_chip.to_irq() return zero on error
gpio: dwapb: Add ACPI device ID for DWAPB GPIO controller on X-Gene platforms
gpio: dt-bindings: add wd,mbl-gpio bindings
gpio: of: make it possible to name GPIO lines
gpio: make gpiod_to_irq() return negative for NO_IRQ
gpio: xgene: implement .get_direction()
gpio: xgene: Enable ACPI support for X-Gene GFC GPIO driver
gpio: tegra: Implement gpio_get_direction callback
gpio: set up initial state from .get_direction()
gpio: rename gpio-generic.c into gpio-mmio.c
gpio: generic: fix GPIO_GENERIC_PLATFORM is set to module case
gpio: dwapb: add gpio-signaled acpi event support
gpio: dwapb: convert device node to fwnode
gpio: dwapb: remove name from dwapb_port_property
gpio/qoriq: select IRQ_DOMAIN
...
In the function, setup_irq(), we don't check that the descriptor
returned from irq_to_desc() is valid before we start using it. For
example chip_bus_lock() called from setup_irq(), assumes that the
descriptor pointer is valid and doesn't check before dereferencing it.
In many other functions including setup/free_percpu_irq() we do check
that the descriptor returned is not NULL and therefore add the same test
to setup_irq() to ensure the descriptor returned is valid.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
In order to prepare the genirq layer for the concept of partitionned
percpu interrupts, let's allow an affinity to be associated with
such an interrupt. We introduce:
- irq_set_percpu_devid_partition: flag an interrupt as a percpu-devid
interrupt, and associate it with an affinity
- irq_get_percpu_devid_partition: allow the affinity of that interrupt
to be retrieved.
This will allow a driver to discover which CPUs the per-cpu interrupt
can actually fire on.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: devicetree@vger.kernel.org
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Rob Herring <robh+dt@kernel.org>
Link: http://lkml.kernel.org/r/1460365075-7316-3-git-send-email-marc.zyngier@arm.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
When iterating over the irq domain list, we try to match a domain
either by calling a match() function or by comparing a number
of fields passed as parameters.
Both approaches are a bit restrictive:
- match() is DT specific and only takes a device node
- the fallback case only deals with the fwnode_handle
It would be useful if we had a per-domain function that would
actually perform the matching check on the whole of the
irq_fwspec structure. This would allow for a domain to triage
matching attempts that need to extend beyond the fwnode.
Let's introduce irq_find_matching_fwspec(), which takes a full
blown irq_fwspec structure, and call into a select() function
implemented by the irqdomain. irq_find_matching_fwnode() is
made a wrapper around irq_find_matching_fwspec in order to
preserve compatibility.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: devicetree@vger.kernel.org
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Rob Herring <robh+dt@kernel.org>
Link: http://lkml.kernel.org/r/1460365075-7316-2-git-send-email-marc.zyngier@arm.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Make these functions return appropriate error codes when something goes
wrong.
Previously irq_destroy_ipi returned void making it impossible to notify
the caller if the request could not be fulfilled. Patch 1 in the series
added another condition in which this could fail in addition to the
existing ones. irq_reserve_ipi returned an unsigned int meaning it could
only return 0 on failure and give the caller no indication as to why the
request failed.
As time goes on there are likely to be further conditions added in which
these functions can fail. These APIs and the IPI IRQ domain are new in
4.6 and the number of existing call sites are low, changing the API now
has little impact on the code, while making it easier for these
functions to grow over time.
Signed-off-by: Matt Redfearn <matt.redfearn@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: jason@lakedaemon.net
Cc: marc.zyngier@arm.com
Cc: ralf@linux-mips.org
Cc: Qais Yousef <qsyousef@gmail.com>
Cc: lisa.parratt@imgtec.com
Cc: jiang.liu@linux.intel.com
Link: http://lkml.kernel.org/r/1461568464-31701-2-git-send-email-matt.redfearn@imgtec.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Wei Yongjun
Thomas Gleixner
Marc Zyngier
Craig Gallek
Alexander Kuleshov
Punit Agrawal
Sebastian Frias
Christoph Hellwig
Shawn Lin
Vincent Stehle
Alexander Popov
Jon Hunter
Keith Busch
Weongyo Jeong
Jianyu Zhan
Matt Redfearn
Matthew Wilcox
Linus Torvalds