Hayes Wang says:
====================
r8152: fix known issues
These patches fix some known issues.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The rx early size should be
(agg_buf_sz - packet size) / 8
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reset the BMU to clear the rx/tx fifo. This avoids that the unexpected
data remains in the hw.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Disable MAC clock speed down. It may casue the first control
transfer to contain the wrong data, when the power state change
from U1 to U0.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexei Starovoitov says:
====================
bpf fixes
Fixes for two bpf bugs:
1st bug reported by Sasha Goldshtein here:
https://github.com/iovisor/bcc/issues/570
2nd discovered by Daniel Borkmann by manual code analysis.
See patches for details.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
similar to bpf_perf_event_output() the bpf_perf_event_read() helper
needs to check the type of the perf_event before reading the counter.
Fixes: a43eec3042 ("bpf: introduce bpf_perf_event_output() helper")
Reported-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ctx structure passed into bpf programs is different depending on bpf
program type. The verifier incorrectly marked ctx->data and ctx->data_end
access based on ctx offset only. That caused loads in tracing programs
int bpf_prog(struct pt_regs *ctx) { .. ctx->ax .. }
to be incorrectly marked as PTR_TO_PACKET which later caused verifier
to reject the program that was actually valid in tracing context.
Fix this by doing program type specific matching of ctx offsets.
Fixes: 969bf05eb3 ("bpf: direct packet access")
Reported-by: Sasha Goldshtein <goldshtn@gmail.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
1) gre_parse_header() can be called from gre_err()
At this point transport header points to ICMP header, not the inner
header.
2) We can not really change transport header as ipgre_err() will later
assume transport header still points to ICMP header (using icmp_hdr())
3) pskb_may_pull() logic in gre_parse_header() really works
if we are interested at zone pointed by skb->data
4) As Jiri explained in commit b7f8fe251e ("gre: do not pull header in
ICMP error processing") we should not pull headers in error handler.
So this fix :
A) changes gre_parse_header() to use skb->data instead of
skb_transport_header()
B) Adds a nhs parameter to gre_parse_header() so that we can skip the
not pulled IP header from error path.
This offset is 0 for normal receive path.
C) remove obsolete IPV6 includes
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Tom Herbert <tom@herbertland.com>
Cc: Maciej Żenczykowski <maze@google.com>
Cc: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The implementation of net_dbg_ratelimited in the CONFIG_DYNAMIC_DEBUG
case was added with 2c94b5373 ("net: Implement net_dbg_ratelimited() for
CONFIG_DYNAMIC_DEBUG case"). The implementation strategy was to take the
usual definition of the dynamic_pr_debug macro, but alter it by adding a
call to "net_ratelimit()" in the if statement. This is, in fact, the
correct approach.
However, while doing this, the author of the commit forgot to surround
fmt by pr_fmt, resulting in unprefixed log messages appearing in the
console. So, this commit adds back the pr_fmt(fmt) invocation, making
net_dbg_ratelimited properly consistent across DEBUG, no DEBUG, and
DYNAMIC_DEBUG cases, and bringing parity with the behavior of
dynamic_pr_debug as well.
Fixes: 2c94b5373 ("net: Implement net_dbg_ratelimited() for CONFIG_DYNAMIC_DEBUG case")
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Cc: Tim Bingham <tbingham@akamai.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The skfp driver has been moved to drivers/net/fddi/skfp a long time
ago, but we still attempt to include headers from the old location,
which causes a warning when building with W=1:
cc1: error: /git/arm-soc/drivers/net/skfp: No such file or directory [-Werror=missing-include-dirs]
cc1: error: drivers/net/skfp: No such file or directory [-Werror=missing-include-dirs]
Clearly this include directive is not needed any more, so we can
just remove it now.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
net/tipc/link.c: In function ‘tipc_link_timeout’:
net/tipc/link.c:744:28: warning: ‘mtyp’ may be used uninitialized in this function [-Wuninitialized]
Fixes: 42b18f605f ("tipc: refactor function tipc_link_timeout()")
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sabrina Dubroca says:
====================
macsec fixes
Patch 1 adds rcu_barrier() during module unload to prevent possible
panics.
Patch 2 allocates memory for scattergather lists and the IV on the
heap, since they can escape the current function's context during
crypto callbacks.
Patch 3 fixes a failure to create secure associations.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The ASYNC flag prevents initialization on some physical machines.
Fixes: c09440f7dc ("macsec: introduce IEEE 802.1AE driver")
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
For the crypto callbacks to work properly, we cannot have sg and iv on
the stack. Use kmalloc instead, with a single allocation for
aead_request + scatterlist + iv.
Fixes: c09440f7dc ("macsec: introduce IEEE 802.1AE driver")
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Without this, the various uses of call_rcu could cause a kernel panic.
Fixes: c09440f7dc ("macsec: introduce IEEE 802.1AE driver")
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
saw a debug splat:
net/include/net/sch_generic.h:287 suspicious rcu_dereference_check() usage!
other info that might help us debug this:
rcu_scheduler_active = 1, debug_locks = 0
2 locks held by kworker/2:1/710:
#0: ("events"){.+.+.+}, at: [<ffffffff8106ca1d>]
#1: ((&q->work)){+.+...}, at: [<ffffffff8106ca1d>] process_one_work+0x14d/0x690
Workqueue: events htb_work_func
Call Trace:
[<ffffffff812dc763>] dump_stack+0x85/0xc2
[<ffffffff8109fee7>] lockdep_rcu_suspicious+0xe7/0x120
[<ffffffff814ced47>] htb_work_func+0x67/0x70
Signed-off-by: Florian Westphal <fw@strlen.de>
Acked-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This refers to commands to direct action access as follows:
sudo tc actions add action drop index 12
sudo tc actions add action pipe index 10
And then dumping them like so:
sudo tc actions ls action gact
iproute2 worked because it depended on absence of TCA_ACT_TAB TLV
as end of message.
This fix has been tested with iproute2 and is backward compatible.
Signed-off-by: Jamal Hadi Salim <jhs@mojatatu.com>
Acked-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
And avoid calling tcf_hash_check() twice.
Fixes: a57f19d30b ("net sched: ipt action fix late binding")
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now prio_init() can return -ENOMEM, it also has to make sure
any allocated qdiscs are freed, since the caller (qdisc_create()) wont
call ->destroy() handler for us.
More generally, we want a transactional behavior for "tc qdisc
change ...", so prio_tune() should not make modifications if
any error is returned.
It means that we must validate parameters and allocate missing qdisc(s)
before taking root qdisc lock exactly once, to not leave the prio qdisc
in an intermediate state.
Fixes: cbdf451164 ("net_sched: prio: properly report out of memory errors")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Maciej Żenczykowski reported lockdep warning a spinlock
was not registered before being held in mlx4_cmd_wake_completions()
cmd.context_lock initialization is not at the right place.
1) mlx4_cmd_use_events() can be called multiple times.
Calling spin_lock_init() on a live spinlock can lead
to hangs.
2) mlx4_cmd_wake_completions() can be called while lock
has not been initialized.
Lockdep complains, and current logic is not race prone.
It seems better to move the initialization earlier in
mlx4_load_one()
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Maciej Żenczykowski <maze@google.com>
Cc: Eugenia Emantayev <eugenia@mellanox.com>
Cc: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
nft_genmask_cur has already done left-shift operator on the gencursor,
so there's no need to do left-shift operator on it again.
Fixes: ea4bd995b0 ("netfilter: nf_tables: add transaction helper functions")
Cc: Patrick McHardy <kaber@trash.net>
Signed-off-by: Liping Zhang <liping.zhang@spreadtrum.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
When we add a nft rule like follows:
# nft add rule filter test tcp dport vmap {1: jump test}
-ELOOP error will be returned, and the anonymous set will be
destroyed.
But after that, nf_tables_abort will also try to remove the
element and destroy the set, which was already destroyed and
freed.
If we add a nft wrong rule, nft_tables_abort will do the cleanup
work rightly, so nf_tables_set_destroy call here is redundant and
wrong, remove it.
Signed-off-by: Liping Zhang <liping.zhang@spreadtrum.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Liping Zhang says:
"Users may add such a wrong nft rules successfully, which will cause an
endless jump loop:
# nft add rule filter test tcp dport vmap {1: jump test}
This is because before we commit, the element in the current anonymous
set is inactive, so osp->walk will skip this element and miss the
validate check."
To resolve this problem, this patch passes the generation mask to the
walk function through the iter container structure depending on the code
path:
1) If we're dumping the elements, then we have to check if the element
is active in the current generation. Thus, we check for the current
bit in the genmask.
2) If we're checking for loops, then we have to check if the element is
active in the next generation, as we're in the middle of a
transaction. Thus, we check for the next bit in the genmask.
Based on original patch from Liping Zhang.
Reported-by: Liping Zhang <liping.zhang@spreadtrum.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Tested-by: Liping Zhang <liping.zhang@spreadtrum.com>
We should check "i" is used as a dictionary or not, "binding" is already
checked before.
Signed-off-by: Liping Zhang <liping.zhang@spreadtrum.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
I forgot to move the kmem_cache_destroy into the exit path.
Fixes: 0c5366b3a8 ("netfilter: conntrack: use single slab cache)
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Nicolas Dichtel says:
====================
ovs: fix rtnl notifications on interface deletion
There was no rtnl notifications for interfaces (gre, vxlan, geneve) created
by ovs. This problem is fixed by adjusting the creation path.
v1 -> v2:
- add patch #1 and #4
- rework error handling in patch #2
====================
Acked-by: Pravin B Shelar <pshelar@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function geneve_dev_create_fb() (only used by ovs) never calls
rtnl_configure_link(). The consequence is that dev->rtnl_link_state is
never set to RTNL_LINK_INITIALIZED.
During the deletion phase, the function rollback_registered_many() sends
a RTM_DELLINK only if dev->rtnl_link_state is set to RTNL_LINK_INITIALIZED.
Fixes: e305ac6cf5 ("geneve: Add support to collect tunnel metadata.")
CC: Pravin B Shelar <pshelar@nicira.com>
CC: Jesse Gross <jesse@nicira.com>
CC: Thomas Graf <tgraf@suug.ch>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function gretap_fb_dev_create() (only used by ovs) never calls
rtnl_configure_link(). The consequence is that dev->rtnl_link_state is
never set to RTNL_LINK_INITIALIZED.
During the deletion phase, the function rollback_registered_many() sends
a RTM_DELLINK only if dev->rtnl_link_state is set to RTNL_LINK_INITIALIZED.
Fixes: b2acd1dc39 ("openvswitch: Use regular GRE net_device instead of vport")
CC: Thomas Graf <tgraf@suug.ch>
CC: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function vxlan_dev_create() (only used by ovs) never calls
rtnl_configure_link(). The consequence is that dev->rtnl_link_state is
never set to RTNL_LINK_INITIALIZED.
During the deletion phase, the function rollback_registered_many() sends
a RTM_DELLINK only if dev->rtnl_link_state is set to RTNL_LINK_INITIALIZED.
Note that the function vxlan_dev_create() is moved after the rtnl stuff so
that vxlan_dellink() can be called in this function.
Fixes: dcc38c033b ("openvswitch: Re-add CONFIG_OPENVSWITCH_VXLAN")
CC: Thomas Graf <tgraf@suug.ch>
CC: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After ipgre_newlink()/geneve_configure() call, the netdev is registered.
Fixes: 7e059158d5 ("vxlan, gre, geneve: Set a large MTU on ovs-created tunnel devices")
CC: David Wragg <david@weave.works>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a corner case in which udp packets belonging to a same
flow are hashed to different socket when hslot->count changes from 10
to 11:
1) When hslot->count <= 10, __udp_lib_lookup() searches udp_table->hash,
and always passes 'daddr' to udp_ehashfn().
2) When hslot->count > 10, __udp_lib_lookup() searches udp_table->hash2,
but may pass 'INADDR_ANY' to udp_ehashfn() if the sockets are bound to
INADDR_ANY instead of some specific addr.
That means when hslot->count changes from 10 to 11, the hash calculated by
udp_ehashfn() is also changed, and the udp packets belonging to a same
flow will be hashed to different socket.
This is easily reproduced:
1) Create 10 udp sockets and bind all of them to 0.0.0.0:40000.
2) From the same host send udp packets to 127.0.0.1:40000, record the
socket index which receives the packets.
3) Create 1 more udp socket and bind it to 0.0.0.0:44096. The number 44096
is 40000 + UDP_HASH_SIZE(4096), this makes the new socket put into the
same hslot as the aformentioned 10 sockets, and makes the hslot->count
change from 10 to 11.
4) From the same host send udp packets to 127.0.0.1:40000, and the socket
index which receives the packets will be different from the one received
in step 2.
This should not happen as the socket bound to 0.0.0.0:44096 should not
change the behavior of the sockets bound to 0.0.0.0:40000.
It's the same case for IPv6, and this patch also fixes that.
Signed-off-by: Su, Xuemin <suxm@chinanetcenter.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the qdisc is full, we drop a packet at the head of the queue,
queue the current skb and return NET_XMIT_CN
Now we track backlog on upper qdiscs, we need to call
qdisc_tree_reduce_backlog(), even if the qlen did not change.
Fixes: 2ccccf5fb4 ("net_sched: update hierarchical backlog too")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: WANG Cong <xiyou.wangcong@gmail.com>
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Acked-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 26c5f03 uses a new skb allocator to avoid the RFD overflow
issue.
But from debugging without datasheet, we found the error always
happen when the DMA RX address is set to 0x....fc0, which is very
likely to be a HW/silicon problem.
So one idea is instead of adding a new allocator, why not just
hitting the right target by avaiding the error-prone DMA address?
This patch will actually
* Remove the commit 26c5f03
* Apply rx skb with 64 bytes longer space, and if the allocated skb
has a 0x...fc0 address, it will use skb_resever(skb, 64) to
advance the address, so that the RX overflow can be avoided.
In theory this method should also apply to atl1c driver, which
I can't find anyone who can help to test on real devices.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=70761
Signed-off-by: Feng Tang <feng.tang@intel.com>
Suggested-by: Eric Dumazet <edumazet@google.com>
Tested-by: Ole Lukoie <olelukoie@mail.ru>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reported-by: Cong Wang <xiyou.wangcong@gmail.com>
Cc: Cong Wang <xiyou.wangcong@gmail.com>
Cc: Tom Herbert <tom@herbertland.com>
Fixes: 4068579e1e ("net: Implmement RFC 6936 (zero RX csums for UDP/IPv6")
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cc: Tom Herbert <tom@herbertland.com>
Fixes: 4068579e1e ("net: Implmement RFC 6936 (zero RX csums for UDP/IPv6")
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cc: Florent Fourcot <florent.fourcot@enst-bretagne.fr>
Fixes: 1d13a96c74 ("ipv6: tcp: fix flowlabel value in ACK messages send from TIME_WAIT")
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
IPv6 ping socket error handler doesn't correctly convert the new 32 bit
mtu to host endianness before using.
Cc: Lorenzo Colitti <lorenzo@google.com>
Fixes: 6d0bfe2261 ("net: ipv6: Add IPv6 support to the ping socket.")
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Acked-by: Lorenzo Colitti <lorenzo@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Configuring the PHY LED registers for the Marvell 88E1510 and others is
not possible, because regardless of the values in marvell,reg-init, it
is later overridden in m88e1121_config_aneg with a non-standard default.
This patch moves that default configuration to .config_init to allow
setting the LED configuration through marvell,reg-init in the device
tree, which should override said default if it exists.
Signed-off-by: Clemens Gruber <clemens.gruber@pqgruber.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
* fix an RCU splat caused when updating the TKIP key
* fix a potential NULL-derefence introduced recently
* fix a IGTK key bug that has existed since the MVM driver was introduced
* fix some fw capabilities checks that got accidentally inverted
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=nj+n
-----END PGP SIGNATURE-----
Merge tag 'iwlwifi-for-kalle-2016-06-10' of git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-fixes
* fix the scan timeout for long scans
* fix an RCU splat caused when updating the TKIP key
* fix a potential NULL-derefence introduced recently
* fix a IGTK key bug that has existed since the MVM driver was introduced
* fix some fw capabilities checks that got accidentally inverted
commit 5c86d97bcc ("ath10k: combine txrx and replenish task")
introduced deadlock while processing rx in order indication message
for qca6174 based devices. While merging replenish and txrx tasklets,
replenish task should be called out of htt rx ring locking since it
is also try to acquire the same lock.
Unfortunately this issue is not exposed by other solutions (qca988x,
qca99x0 & qca4019), as rx_in_ord_ind message is specific to qca6174
based devices. This patch fixes
=============================================
[ INFO: possible recursive locking detected ]
4.7.0-rc2-wt-ath+ #1353 Tainted: G E
---------------------------------------------
swapper/3/0 is trying to acquire lock:
(&(&htt->rx_ring.lock)->rlock){+.-...}, at: [<f8d7ef19>]
ath10k_htt_rx_msdu_buff_replenish+0x29/0x90 [ath10k_core]
but task is already holding lock:
(&(&htt->rx_ring.lock)->rlock){+.-...}, at: [<f8d82cab>]
ath10k_htt_txrx_compl_task+0x21b/0x250 [ath10k_core]
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0
----
lock(&(&htt->rx_ring.lock)->rlock);
lock(&(&htt->rx_ring.lock)->rlock);
*** DEADLOCK ***
May be due to missing lock nesting notation
1 lock held by swapper/3/0:
#0: (&(&htt->rx_ring.lock)->rlock){+.-...}, at: [<f8d82cab>]
ath10k_htt_txrx_compl_task+0x21b/0x250 [ath10k_core]
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=119151
Fixes: 5c86d97bcc ("ath10k: combine txrx and replenish task")
Reported-by: Mike Lothian <mike@fireburn.co.uk>
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
There is no reason to destroy channels that are destroyed while
cpdma_ctlr destroy. In this case no need to remember how much
channels where created and destroy them by one, as cpdma_ctlr
destroys all of them.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
At Qdisc creation or change time, prio_tune() creates missing
pfifo qdiscs but does not return an error code if one
qdisc could not be allocated.
Leaving a qdisc in non operational state without telling user
anything about this problem is not good.
Also, testing if we replace something different than noop_qdisc
a second time makes no sense so I removed useless code.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
>> net/ipv4/ipconfig.c:130:15: warning: 'ic_addrservaddr' defined but not used [-Wunused-variable]
static __be32 ic_addrservaddr = NONE; /* IP Address of the IP addresses'server */
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 7f854420fb
("phy: Add API for {un}registering an mdio device to a bus.")
broke PHY detection on this driver with a copy-paste bug:
The code is looking 32 times for a PHY at address 0.
Fixes ethernet on AMD DB1100/DB1500/DB1550 boards which have
their (autodetected) PHYs at address 31.
Cc: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 7f854420fb
("phy: Add API for {un}registering an mdio device to a bus.")
broke PHY detection on this driver with a copy-paste bug:
The code is looking 32 times for a PHY at address 0.
Fixes ethernet on AMD DB1100/DB1500/DB1550 boards which have
their (autodetected) PHYs at address 31.
Cc: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
John Crispin says:
====================
net: mediatek: various small fixes
This series contains various small fixes that we stumbled across while
doing thorough testing and code level reviewing of the driver.
Changes in V2:
* drop the DQL patch from the list until a better solution is found
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The code checks if the queue should be stopped because we are below the
threshold of free descriptors only to check if it should be started again.
If we do end up in a state where we are at the threshold limit, it makes
more sense to just stop the queue and wait for the next IRQ to trigger the
TX housekeeping again. There is no rush in enqueuing the next packet, it
needs to wait for all the others in the queue to be dispatched first
anyway.
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller
hayeswang
Alexei Starovoitov
Eric Dumazet
Jason A. Donenfeld
Arnd Bergmann
Ying Xue
Sabrina Dubroca
Florian Westphal
Jamal Hadi Salim
WANG Cong
Liping Zhang
Pablo Neira Ayuso
Nicolas Dichtel
Su, Xuemin
Feng Tang
Hannes Frederic Sowa
Clemens Gruber
Kalle Valo
Miaoqing Pan
Rajkumar Manoharan
Ivan Khoronzhuk
Manuel Lauss
John Crispin