commit df8fdd01c9 upstream.
As per the datasheet, the clock selection Bits 2:0 – TCCLKS[2:0] should
be set to 0 while using the internal GCLK (TIMER_CLOCK1).
Fixes: 106b104137 ("counter: Add microchip TCB capture counter")
Signed-off-by: Dharma Balasubiramani <dharma.b@microchip.com>
Link: https://lore.kernel.org/r/20230905100835.315024-1-dharma.b@microchip.com
Signed-off-by: William Breathitt Gray <william.gray@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4aa3b75c74 upstream.
The Counter (CNTR) register is 24 bits wide, but we can have an
effective 25-bit count value by setting bit 24 to the XOR of the Borrow
flag and Carry flag. The flags can be read from the FLAG register, but a
race condition exists: the Borrow flag and Carry flag are instantaneous
and could change by the time the count value is read from the CNTR
register.
Since the race condition could result in an incorrect 25-bit count
value, remove support for 25-bit count values from this driver;
hard-coded maximum count values are replaced by a LS7267_CNTR_MAX define
for consistency and clarity.
Fixes: 28e5d3bb03 ("iio: 104-quad-8: Add IIO support for the ACCES 104-QUAD-8")
Cc: <stable@vger.kernel.org> # 6.1.x
Cc: <stable@vger.kernel.org> # 6.2.x
Link: https://lore.kernel.org/r/20230312231554.134858-1-william.gray@linaro.org/
Signed-off-by: William Breathitt Gray <william.gray@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 00f4bc5184 ]
Signal 16 and higher represent the device's Index lines. The
priv->preset_enable array holds the device configuration for these Index
lines. The preset_enable configuration is active low on the device, so
invert the conditional check in quad8_action_read() to properly handle
the logical state of preset_enable.
Fixes: f1d8a071d4 ("counter: 104-quad-8: Add Generic Counter interface support")
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20230316203426.224745-1-william.gray@linaro.org/
Signed-off-by: William Breathitt Gray <william.gray@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit aaec1a0f76 ]
This is a reimplementation of the Generic Counter driver interface.
There are no modifications to the Counter subsystem userspace interface,
so existing userspace applications should continue to run seamlessly.
The purpose of this patch is to internalize the sysfs interface code
among the various counter drivers into a shared module. Counter drivers
pass and take data natively (i.e. u8, u64, etc.) and the shared counter
module handles the translation between the sysfs interface and the
device drivers. This guarantees a standard userspace interface for all
counter drivers, and helps generalize the Generic Counter driver ABI in
order to support the Generic Counter chrdev interface (introduced in a
subsequent patch) without significant changes to the existing counter
drivers.
Note, Counter device registration is the same as before: drivers
populate a struct counter_device with components and callbacks, then
pass the structure to the devm_counter_register function. However,
what's different now is how the Counter subsystem code handles this
registration internally.
Whereas before callbacks would interact directly with sysfs data, this
interaction is now abstracted and instead callbacks interact with native
C data types. The counter_comp structure forms the basis for Counter
extensions.
The counter-sysfs.c file contains the code to parse through the
counter_device structure and register the requested components and
extensions. Attributes are created and populated based on type, with
respective translation functions to handle the mapping between sysfs and
the counter driver callbacks.
The translation performed for each attribute is straightforward: the
attribute type and data is parsed from the counter_attribute structure,
the respective counter driver read/write callback is called, and sysfs
I/O is handled before or after the driver read/write function is called.
Cc: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Cc: Patrick Havelange <patrick.havelange@essensium.com>
Cc: Kamel Bouhara <kamel.bouhara@bootlin.com>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Syed Nayyar Waris <syednwaris@gmail.com>
Reviewed-by: David Lechner <david@lechnology.com>
Tested-by: David Lechner <david@lechnology.com>
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Reviewed-by: Fabrice Gasnier <fabrice.gasnier@foss.st.com> # for stm32
Link: https://lore.kernel.org/r/c68b4a1ffb195c1a2f65e8dd5ad7b7c14e79c6ef.1630031207.git.vilhelm.gray@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Stable-dep-of: 00f4bc5184 ("counter: 104-quad-8: Fix Synapse action reported for Index signals")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fd5ac974fc ]
The ARR (auto reload register) and CMP (compare) registers are
successively written. The status bits to check the update of these
registers are polled together with regmap_read_poll_timeout().
The condition to end the loop may become true, even if one of the register
isn't correctly updated.
So ensure both status bits are set before clearing them.
Fixes: d8958824cf ("iio: counter: Add support for STM32 LPTimer")
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@foss.st.com>
Link: https://lore.kernel.org/r/20221123133609.465614-1-fabrice.gasnier@foss.st.com/
Signed-off-by: William Breathitt Gray <william.gray@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit d917a62af8 upstream.
The signal_read(), action_read(), and action_write() callbacks have been
assuming Signal0 is requested without checking. This results in requests
for Signal1 returning data for Signal0. This patch fixes these
oversights by properly checking for the Signal's id in the respective
callbacks and handling accordingly based on the particular Signal
requested. The trig_inverted member of the mchp_tc_data is removed as
superfluous.
Fixes: 106b104137 ("counter: Add microchip TCB capture counter")
Cc: stable@vger.kernel.org
Reviewed-by: Kamel Bouhara <kamel.bouhara@bootlin.com>
Link: https://lore.kernel.org/r/20221018121014.7368-1-william.gray@linaro.org/
Signed-off-by: William Breathitt Gray <william.gray@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The phrase "Counter Count function" is verbose and unintentionally
implies that function is a Count extension. This patch adjusts the
Counter subsystem code to use the more direct "Counter function" phrase
to make the intent of this code clearer.
Cc: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Cc: Patrick Havelange <patrick.havelange@essensium.com>
Cc: Oleksij Rempel <o.rempel@pengutronix.de>
Cc: Kamel Bouhara <kamel.bouhara@bootlin.com>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: David Lechner <david@lechnology.com>
Acked-by: Syed Nayyar Waris <syednwaris@gmail.com>
Reviewed-by: Fabrice Gasnier <fabrice.gasnier@foss.st.com>
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Link: https://lore.kernel.org/r/8268c54d6f42075a19bb08151a37831e22652499.1627990337.git.vilhelm.gray@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signal values will always be levels so let's be explicit it about it to
make the intent of the code clear.
Cc: Oleksij Rempel <o.rempel@pengutronix.de>
Cc: Kamel Bouhara <kamel.bouhara@bootlin.com>
Acked-by: Syed Nayyar Waris <syednwaris@gmail.com>
Reviewed-by: David Lechner <david@lechnology.com>
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Link: https://lore.kernel.org/r/3f17010abe2415859cea9a5fddabd3c97f635ff5.1627990337.git.vilhelm.gray@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
ERANGE is a semantically better error code to return when an argument
value falls outside the supported limit range of a device.
Cc: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Cc: Oleksij Rempel <o.rempel@pengutronix.de>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Acked-by: Syed Nayyar Waris <syednwaris@gmail.com>
Reviewed-by: David Lechner <david@lechnology.com>
Reviewed-by: Fabrice Gasnier <fabrice.gasnier@foss.st.com>
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Link: https://lore.kernel.org/r/ae8d3b20b8b02c96b1c9898ffa2f9fa5d99edc81.1627990337.git.vilhelm.gray@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Only a select set of modes (function, action, etc.) are valid for a
given device configuration. This patch ensures that invalid modes result
in a return -EINVAL. Such a situation should never occur in reality, but
it's good to define a default switch case for the sake of making the
intent of the code clear.
Cc: Kamel Bouhara <kamel.bouhara@bootlin.com>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Acked-by: David Lechner <david@lechnology.com>
Acked-by: Syed Nayyar Waris <syednwaris@gmail.com>
Reviewed-by: Fabrice Gasnier <fabrice.gasnier@foss.st.com>
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Link: https://lore.kernel.org/r/7af82d4e39610da11edce0ee370285fe1cb1eac8.1627990337.git.vilhelm.gray@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The 104-QUAD-8 only has two count modes where a ceiling value makes
sense: Range Limit and Modulo-N. Outside of these two modes, setting a
ceiling value is an invalid operation -- so let's report it as such by
returning -EINVAL.
Fixes: fc06926226 ("counter: 104-quad-8: Add lock guards - generic interface")
Acked-by: Syed Nayyar Waris <syednwaris@gmail.com>
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Link: https://lore.kernel.org/r/a2147f022829b66839a1db5530a7fada47856847.1627990337.git.vilhelm.gray@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
0-DAY CI Kernel Test Service reported following iwyu warning:
drivers/counter/intel-qep.c:11:1: iwyu: warning: superfluous #include <linux/bitops.h>
Remove that include since we don't seem to use anything from it.
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Acked-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Link: https://lore.kernel.org/r/20210629111657.2655688-1-jarkko.nikula@linux.intel.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The struct counter_synapse actions_list member expects a const enum
counter_synapse_action array. This patch renames
interrupt_cnt_synapse_actionss to interrupt_cnt_synapse_actions and adds
a const qualifier to match actions_list.
Cc: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Reviewed-by: <o.rempel@pengutronix.de>
Link: https://lore.kernel.org/r/20210610013642.149961-1-vilhelm.gray@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Use to_pci_dev() helper instead of container_of(d, struct pci_dev, dev);
Suggested-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Acked-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Link: https://lore.kernel.org/r/20210611115558.796338-2-jarkko.nikula@linux.intel.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Remove CONFIG_PM ifdef and mark PM callbacks with __maybe_unused.
Suggested-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Acked-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Link: https://lore.kernel.org/r/20210611115558.796338-1-jarkko.nikula@linux.intel.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The struct counter_synapse actions_list member expects a const enum
counter_synapse_action array. This patch adds the const qualifier to the
stm32_synapse_actions to match actions_list.
Cc: Benjamin Gaignard <benjamin.gaignard@st.com>
Reviewed-by: Fabrice Gasnier <fabrice.gasnier@foss.st.com>
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Link: https://lore.kernel.org/r/9675edda958ee2ca371d271f46445d3e1934ba82.1623201081.git.vilhelm.gray@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The struct counter_synapse actions_list member expects a const enum
counter_synapse_action array. This patch adds the const qualifier to the
stm32_lptim_cnt_synapse_actions to match actions_list.
Reviewed-by: Fabrice Gasnier <fabrice.gasnier@foss.st.com>
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Link: https://lore.kernel.org/r/785e0daa3633923ede42394f423fcf94c4469154.1623201081.git.vilhelm.gray@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The struct counter_synapse actions_list member expects a const enum
counter_synapse_action array. This patch adds the const qualifier to the
mchp_tc_synapse_actions to match actions_list.
Cc: Kamel Bouhara <kamel.bouhara@bootlin.com>
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Link: https://lore.kernel.org/r/165f9682ce308a60a477aaa56fdae7bc949dc218.1623201081.git.vilhelm.gray@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The struct counter_synapse actions_list member expects a const enum
counter_synapse_action array. This patch adds the const qualifier to the
ftm_quaddec_synapse_actions to match actions_list.
Cc: Patrick Havelange <patrick.havelange@essensium.com>
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Link: https://lore.kernel.org/r/db1df2021efb1b98e6d1a50787be5a52a1896574.1623201081.git.vilhelm.gray@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The struct counter_synapse actions_list member expects a const enum
counter_synapse_action array. This patch adds the const qualifier to the
quad8_index_actions_list and quad8_synapse_actions_list to match
actions_list.
Acked-by: Syed Nayyar Waris <syednwaris@gmail.com>
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Link: https://lore.kernel.org/r/776ba3ad0a3c609d3600cffe0ed6446baf29fee9.1623201081.git.vilhelm.gray@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The struct counter_count functions_list member expects a const enum
counter_count_function array. This patch adds the const qualifier to the
stm32_count_functions to match functions_list.
Cc: Benjamin Gaignard <benjamin.gaignard@st.com>
Reviewed-by: Fabrice Gasnier <fabrice.gasnier@foss.st.com>
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Link: https://lore.kernel.org/r/46a1e7096dd9280d8f241894186b3c903956a55f.1623201081.git.vilhelm.gray@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The struct counter_count functions_list member expects a const enum
counter_count_function array. This patch adds the const qualifier to the
stm32_lptim_cnt_functions to match functions_list.
Reviewed-by: Fabrice Gasnier <fabrice.gasnier@foss.st.com>
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Link: https://lore.kernel.org/r/08830119594acdb3bc9d36ae2e65b2eb26589ade.1623201081.git.vilhelm.gray@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The struct counter_count functions_list member expects a const enum
counter_count_function array. This patch adds the const qualifier to the
mchp_tc_count_functions to match functions_list.
Cc: Kamel Bouhara <kamel.bouhara@bootlin.com>
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Link: https://lore.kernel.org/r/74cb91ab7b459563762ec28633cd8808093aa2ad.1623201081.git.vilhelm.gray@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The struct counter_count functions_list member expects a const enum
counter_count_function array. This patch adds the const qualifier to the
interrupt__cnt_functions to match functions_list.
Cc: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Link: https://lore.kernel.org/r/86f7fb77f703cf2508a6b4ee9cf80aa523392976.1623201081.git.vilhelm.gray@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The struct counter_count functions_list member expects a const enum
counter_count_function array. This patch adds the const qualifier to the
quad8_count_functions_list to match functions_list.
Acked-by: Syed Nayyar Waris <syednwaris@gmail.com>
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Link: https://lore.kernel.org/r/6847da7553208e7f2554e6c7688e2021f7e19716.1623201081.git.vilhelm.gray@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
When the kernel is running in secure boot mode, we lock down the kernel to
prevent userspace from modifying the running kernel image. Whilst this
includes prohibiting access to things like /dev/mem, it must also prevent
access by means of configuring driver modules in such a way as to cause a
device to access or modify the kernel image.
To this end, annotate module_param* statements that refer to hardware
configuration and indicate for future reference what type of parameter they
specify. The parameter parser in the core sees this information and can
skip such parameters with an error message if the kernel is locked down.
The module initialisation then runs as normal, but just sees whatever the
default values for those parameters is.
Note that we do still need to do the module initialisation because some
drivers have viable defaults set in case parameters aren't specified and
some drivers support automatic configuration (e.g. PNP or PCI) in addition
to manually coded parameters.
This patch annotates the 104-QUAD-8 driver.
Acked-by: Syed Nayyar Waris <syednwaris@gmail.com>
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Link: https://lore.kernel.org/r/97ce79878a26809f0b15b2eac9a86ca39e0ecd74.1623201081.git.vilhelm.gray@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add support for Intel Quadrature Encoder Peripheral found on Intel
Elkhart Lake platform.
Initial implementation was done by Felipe Balbi while he was working at
Intel with later changes from Raymond Tan and me.
Co-developed-by: Felipe Balbi (Intel) <balbi@kernel.org>
Signed-off-by: Felipe Balbi (Intel) <balbi@kernel.org>
Co-developed-by: Raymond Tan <raymond.tan@intel.com>
Signed-off-by: Raymond Tan <raymond.tan@intel.com>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Acked-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Link: https://lore.kernel.org/r/20210602113259.158674-1-jarkko.nikula@linux.intel.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Big set in here from Alexandru Ardelean enabling multiple buffer support.
This includes providing a new directory per buffer that combines
what was previously in buffer/ and scan_elements/. Old interfaces still
in place for compatiblity.
Note immuatable branch for scmi patches to allow for some significant
rework going on in that subsystem. Merge required updating to reflect
some changes in IIO.
Late rebase to fix some wrong fixes tags due to some earlier rebases
made necessary by messing up the immutable branch.
IIO New Device Support
* adi,ad5686
- Add info to support AD5673R and AD5677R
* bosch,bmi088
- New driver supporting this accelerometer + gyroscope
* cros_ec_mkbp
- New driver for this proximity sensor that exposes a 'front'
sensor. Very simple switch like device, but driver allows it
to share interface with more sophisticated proximity sensors.
* iio_scmi
- New driver to support ARM SCMI protocol to expose underlying
accelerometers and gyroscopes via this firmware interface.
* st,st_magn
- Add ID for IISMDC magnetometer.
* ti,ads131e0
- New driver supporting ads131e04, ads131e06 and ads131e08 24 bit ADCs
Counter New Device Support
* IRQ or GPIO based counter
- New driver for a conceptually simple counter that uses interrupts
to perform the count.
Features
* core
- Dual buffer supprt including:
Various helpers to centralize handling of bufferer related elements.
Document existing and new IOCTLs
Register the IIO chrdev only if it can actually be used for anything.
Rework attribute group creation in the core (lots of patches)
Merge buffer/ and scan_elements/ entries into one list + maintain
backwards compatible set.
Introduce the internal logic and IOCTL to allow multiple buffers
+ access to an anon FD per buffer to actually read from it.
Tidy up tools/iio/iio_generic_buffer and switch to new interfaces.
Update ABI docs.
A few follow up fixes, unsuprising as this was a huge bit of rework.
- Move common case setting of trig->parent to the core.
- Provide an iio_read_channel_processed_scale() to avoid loss of
precision from iio_read_channel_processed() then applying integer
scale. Use it in ntc_thermistor driver in hwmon.
- Allow drivers to specify labels from elsewhere than DT. Use it for
bmc150 and kxcjk-1013 labels related to position on 2 in one tablets.
- Document label usage for proximity and accelerometer sensors.
- Some local variable renames for consistency
tools
- Add -a parameter to iio_event_monitor to allow autoenabling of events.
* acpi_als
- Add trigger support for devices that don't support notification method.
* adi,ad7124
- Allow more than 8 channels. This is a complex little device, but is
capable of supporting up to 16 channels if the share certain
configuration settings.
* hrtimer-trigger
- Support sampling frequency below 1Hz.
* mediatek,mt8195-auxadc
- Add compatible to binding docs (always also includes mt8173)
* st,stm32-adc
- Enable timetamps when not using DMA.
* vishay,vcnl3020
- Sampling frequency control.
Cleanup and minor fixes:
* treewide
- Use some getter and setter functions instead of opencoding.
- Set of fixes for pointless casts in various drivers.
- Avoid wrong kernel-doc marking on comment blocks.
- Fix various other minor kernel-doc issues shown by W=1
* core
- Use a signed temporary for IIO_VAL_FRACTIONAL_LOG2 to avoid odd casts.
- Fix IIO_VAL_FRACTIONAL_LOG2 for values between -1.0 and 0.0
- Add unit tests for iio_format_value()
* docs
- Fix formatting/typos in iio_configfs.rst and buffers.rst
- Add documentation of index in buffers.rst
- Fix scan element description
- Avoid some issues with HTML generation from ABI docs by moving
duplicated defintions to more generic files.
- Drop reference to long dead mailing list.
* 104-quad
- Remove left over deprecated IIO counter ABI.
* adi,adi-axi-adc
- Fix wrong bit of docs.
* adi,ad5791
- Typos
* adi,ad9834
- Switch to device managed functions in probe.
* adi,adis*
- Add and use helpers for locking to reduced duplication.
* adi,adis16480
- Fix calculation of sampling frequency when using pulse per second input.
* adi,adis16475
- Calculate the IMU scaled internal sampling rate and runtime depending
on sysfs based configuration rather than getting from DT. Drop now
unnecessary property from DT bindings doc.
* cros_ec
- Fix result of a series of recent changes that means extended buffer
attributes turn up in the wrong place. Too complex to revert the
various patches unfortunately so this is a bit messy.
* fsl,mma3452
- Indentation cleanup.
* hid-sensors
- Size of storage needs to increase for some parts when using quaternions.
- Move the get sensistivity attribute to hid-sensors-common to reduce
duplication. Enable it for more device types.
- Correctly handle relative sensitivity if reported that way including
documenting the new ABI.
* maxim,max517
- Use device managed functions in probe.
* mediatek,mt6360-adc
- Use asm/unaligned.h instead of directly including
unaligned/be_byteshift.h
* novuton,npcm-adc
- Local lock instead of missusing mlock.
* semtech,sx9500
- Typos
* st,sensor
- typo fix
* st,spear-adc
- Local lock instead of missusing mlock.
* st,stm32-adc
- Long standing HAS_IOMEM dependency fix.
* st,stm32-counter
- Remove left over deprecated IIO counter ABI.
* ti,palmas-adc
- Local lock instead of missusing mlock.
* ti,tmp007
- Switch to device managed functions in probe.
Other
* MAINTAINERS
- Move Peter Meerwald-Stadler to Credits at his request
-----BEGIN PGP SIGNATURE-----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=jeRJ
-----END PGP SIGNATURE-----
Merge tag 'iio-for-5.13a' of https://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
1st set of IIO/counter device support, features and cleanup in the 5.13 cycle
Big set in here from Alexandru Ardelean enabling multiple buffer support.
This includes providing a new directory per buffer that combines
what was previously in buffer/ and scan_elements/. Old interfaces still
in place for compatiblity.
Note immuatable branch for scmi patches to allow for some significant
rework going on in that subsystem. Merge required updating to reflect
some changes in IIO.
Late rebase to fix some wrong fixes tags due to some earlier rebases
made necessary by messing up the immutable branch.
IIO New Device Support
* adi,ad5686
- Add info to support AD5673R and AD5677R
* bosch,bmi088
- New driver supporting this accelerometer + gyroscope
* cros_ec_mkbp
- New driver for this proximity sensor that exposes a 'front'
sensor. Very simple switch like device, but driver allows it
to share interface with more sophisticated proximity sensors.
* iio_scmi
- New driver to support ARM SCMI protocol to expose underlying
accelerometers and gyroscopes via this firmware interface.
* st,st_magn
- Add ID for IISMDC magnetometer.
* ti,ads131e0
- New driver supporting ads131e04, ads131e06 and ads131e08 24 bit ADCs
Counter New Device Support
* IRQ or GPIO based counter
- New driver for a conceptually simple counter that uses interrupts
to perform the count.
Features
* core
- Dual buffer supprt including:
Various helpers to centralize handling of bufferer related elements.
Document existing and new IOCTLs
Register the IIO chrdev only if it can actually be used for anything.
Rework attribute group creation in the core (lots of patches)
Merge buffer/ and scan_elements/ entries into one list + maintain
backwards compatible set.
Introduce the internal logic and IOCTL to allow multiple buffers
+ access to an anon FD per buffer to actually read from it.
Tidy up tools/iio/iio_generic_buffer and switch to new interfaces.
Update ABI docs.
A few follow up fixes, unsuprising as this was a huge bit of rework.
- Move common case setting of trig->parent to the core.
- Provide an iio_read_channel_processed_scale() to avoid loss of
precision from iio_read_channel_processed() then applying integer
scale. Use it in ntc_thermistor driver in hwmon.
- Allow drivers to specify labels from elsewhere than DT. Use it for
bmc150 and kxcjk-1013 labels related to position on 2 in one tablets.
- Document label usage for proximity and accelerometer sensors.
- Some local variable renames for consistency
tools
- Add -a parameter to iio_event_monitor to allow autoenabling of events.
* acpi_als
- Add trigger support for devices that don't support notification method.
* adi,ad7124
- Allow more than 8 channels. This is a complex little device, but is
capable of supporting up to 16 channels if the share certain
configuration settings.
* hrtimer-trigger
- Support sampling frequency below 1Hz.
* mediatek,mt8195-auxadc
- Add compatible to binding docs (always also includes mt8173)
* st,stm32-adc
- Enable timetamps when not using DMA.
* vishay,vcnl3020
- Sampling frequency control.
Cleanup and minor fixes:
* treewide
- Use some getter and setter functions instead of opencoding.
- Set of fixes for pointless casts in various drivers.
- Avoid wrong kernel-doc marking on comment blocks.
- Fix various other minor kernel-doc issues shown by W=1
* core
- Use a signed temporary for IIO_VAL_FRACTIONAL_LOG2 to avoid odd casts.
- Fix IIO_VAL_FRACTIONAL_LOG2 for values between -1.0 and 0.0
- Add unit tests for iio_format_value()
* docs
- Fix formatting/typos in iio_configfs.rst and buffers.rst
- Add documentation of index in buffers.rst
- Fix scan element description
- Avoid some issues with HTML generation from ABI docs by moving
duplicated defintions to more generic files.
- Drop reference to long dead mailing list.
* 104-quad
- Remove left over deprecated IIO counter ABI.
* adi,adi-axi-adc
- Fix wrong bit of docs.
* adi,ad5791
- Typos
* adi,ad9834
- Switch to device managed functions in probe.
* adi,adis*
- Add and use helpers for locking to reduced duplication.
* adi,adis16480
- Fix calculation of sampling frequency when using pulse per second input.
* adi,adis16475
- Calculate the IMU scaled internal sampling rate and runtime depending
on sysfs based configuration rather than getting from DT. Drop now
unnecessary property from DT bindings doc.
* cros_ec
- Fix result of a series of recent changes that means extended buffer
attributes turn up in the wrong place. Too complex to revert the
various patches unfortunately so this is a bit messy.
* fsl,mma3452
- Indentation cleanup.
* hid-sensors
- Size of storage needs to increase for some parts when using quaternions.
- Move the get sensistivity attribute to hid-sensors-common to reduce
duplication. Enable it for more device types.
- Correctly handle relative sensitivity if reported that way including
documenting the new ABI.
* maxim,max517
- Use device managed functions in probe.
* mediatek,mt6360-adc
- Use asm/unaligned.h instead of directly including
unaligned/be_byteshift.h
* novuton,npcm-adc
- Local lock instead of missusing mlock.
* semtech,sx9500
- Typos
* st,sensor
- typo fix
* st,spear-adc
- Local lock instead of missusing mlock.
* st,stm32-adc
- Long standing HAS_IOMEM dependency fix.
* st,stm32-counter
- Remove left over deprecated IIO counter ABI.
* ti,palmas-adc
- Local lock instead of missusing mlock.
* ti,tmp007
- Switch to device managed functions in probe.
Other
* MAINTAINERS
- Move Peter Meerwald-Stadler to Credits at his request
* tag 'iio-for-5.13a' of https://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio: (119 commits)
iio: acpi_als: Add trigger support
iio: acpi_als: Add local variable dev in probe
iio: acpi_als: Add timestamp channel
iio: adc: ad7292: Modify the bool initialization assignment
iio: cros: unify hw fifo attributes without API changes
iio: kfifo: add devm_iio_triggered_buffer_setup_ext variant
iio: event_monitor: Enable events before monitoring
dt-bindings: iio: adc: Add compatible for Mediatek MT8195
iio:magnetometer: Add Support for ST IIS2MDC
dt-bindings: iio: st,st-sensors add IIS2MDC.
staging: iio: ad9832: kernel-doc fixes
iio:dac:max517.c: Use devm_iio_device_register()
iio:cros_ec_sensors: Fix a wrong function name in kernel doc.
iio: buffer: kfifo_buf: kernel-doc, typo in function name.
iio: accel: sca3000: kernel-doc fixes. Missing - and wrong function names.
iio: adc: adi-axi-adc: Drop false marking for kernel-doc
iio: adc: cpcap-adc: kernel-doc fix - that should be _ in structure name
iio: dac: ad5504: fix wrong part number in kernel-doc structure name.
iio: dac: ad5770r: kernel-doc fix case of letter R wrong in structure name
iio: adc: ti-adc084s021: kernel-doc fixes, missing function names
...
Add simple IRQ or GPIO base counter. This device is used to measure
rotation speed of some agricultural devices, so no high frequency on the
counter pin is expected.
The maximal measurement frequency depends on the CPU and system load. On
the idle iMX6S I was able to measure up to 20kHz without count drops.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Reviewed-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Link: https://lore.kernel.org/r/20210301080401.22190-3-o.rempel@pengutronix.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Currently, the STM32 LP Timer counter driver registers into both IIO and
counter subsystems, which is redundant.
Remove the IIO counter ABI and IIO registration from the STM32 LP Timer
counter driver since it's been superseded by the Counter subsystem
as discussed in [1].
Keep only the counter subsystem related part.
Move a part of the ABI documentation into a driver comment.
This also removes a duplicate ABI warning
$ scripts/get_abi.pl validate
...
/sys/bus/iio/devices/iio:deviceX/in_count0_preset is defined 2 times:
./Documentation/ABI/testing/sysfs-bus-iio-timer-stm32:100
./Documentation/ABI/testing/sysfs-bus-iio-lptimer-stm32:0
[1] https://lkml.org/lkml/2021/1/19/347
Acked-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@foss.st.com>
Link: https://lore.kernel.org/r/1611926542-2490-1-git-send-email-fabrice.gasnier@foss.st.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Ceiling value may be miss-aligned with what's actually configured into the
ARR register. This is seen after probe as currently the ARR value is zero,
whereas ceiling value is set to the maximum. So:
- reading ceiling reports zero
- in case the counter gets enabled without any prior configuration,
it won't count.
- in case the function gets set by the user 1st, (priv->ceiling) is used.
Fix it by getting rid of the cached "priv->ceiling" variable. Rather use
the ARR register value directly by using regmap read or write when needed.
There should be no drawback on performance as priv->ceiling isn't used in
performance critical path.
There's also no point in writing ARR while setting function (sms), so
it can be safely removed.
Fixes: ad29937e20 ("counter: Add STM32 Timer quadrature encoder")
Suggested-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@foss.st.com>
Acked-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Cc: <Stable@vger.kernel.org>
Link: https://lore.kernel.org/r/1614793789-10346-1-git-send-email-fabrice.gasnier@foss.st.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The ceiling value isn't checked before writing it into registers. The user
could write a value higher than the counter resolution (e.g. 16 or 32 bits
indicated by max_arr). This makes most significant bits to be truncated.
Fix it by checking the max_arr to report a range error [1] to the user.
[1] https://lkml.org/lkml/2021/2/12/358
Fixes: ad29937e20 ("counter: Add STM32 Timer quadrature encoder")
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@foss.st.com>
Acked-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Cc: <Stable@vger.kernel.org>
Link: https://lore.kernel.org/r/1614696235-24088-1-git-send-email-fabrice.gasnier@foss.st.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
When in SLAVE_MODE_DISABLED mode, the count still increases if the
counter is enabled because an internal clock is used. This patch fixes
the stm32_count_function_get() and stm32_count_function_set() functions
to properly handle this behavior.
Fixes: ad29937e20 ("counter: Add STM32 Timer quadrature encoder")
Cc: Fabrice Gasnier <fabrice.gasnier@st.com>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Reviewed-by: Fabrice Gasnier <fabrice.gasnier@foss.st.com>
Link: https://lore.kernel.org/r/20210226012931.161429-1-vilhelm.gray@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The hardware doesn't support this. QPOSINIT is an initialization value
that is triggered by other things. When the counter overflows, it
always wraps around to zero.
Fixes: f213729f67 "counter: new TI eQEP driver"
Signed-off-by: David Lechner <david@lechnology.com>
Acked-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Link: https://lore.kernel.org/r/20201214000927.1793062-1-david@lechnology.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The ATMEL_TC_ETRGEDG_* defines are not masks but rather possible values
for CMR. This patch fixes the action_get() callback to properly check
for these values rather than mask them.
Fixes: 106b104137 ("counter: Add microchip TCB capture counter")
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Acked-by: Kamel Bouhara <kamel.bouhara@bootlin.com>
Cc: <Stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20201114232805.253108-1-vilhelm.gray@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The values given were the offset of the register after the last
register instead of the actual last register in each range. Fix
by using the correct last register of each range.
Fixes: f213729f67 ("counter: new TI eQEP driver")
Signed-off-by: David Lechner <david@lechnology.com>
Acked-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Link: https://lore.kernel.org/r/20201025165122.607866-1-david@lechnology.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Replace commas with semicolons. What is done is essentially described by
the following Coccinelle semantic patch (http://coccinelle.lip6.fr/):
// <smpl>
@@ expression e1,e2; @@
e1
-,
+;
e2
... when any
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@inria.fr>
Reviewed-by: David Lechner <david@lechnology.com>
Link: https://lore.kernel.org/r/1601233948-11629-16-git-send-email-Julia.Lawall@inria.fr
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The only usage of mchp_tc_ops is to assign its address to the ops field
in the counter_device struct which is a const pointer. Make it const to
allow the compiler to put it in read-only memory.
Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com>
Acked-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Link: https://lore.kernel.org/r/20200922201941.41328-1-rikard.falkeborn@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This should be testing "regmap" instead of "priv->regmap". The
"priv->regmap" variable is always zero so it's not an error pointer.
Fixes: 106b104137 ("counter: Add microchip TCB capture counter")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This drivers allows to use the capture mode of the Timer Counter Block
hardware block available in Microchip SoCs through the counter subsystem.
Two functions of the counter are supported for the moment: period
capture and quadrature decoder. The latter is only supported by the
SAMA5 series of SoCs.
For the period capture mode a basic setup has been chosen that will
reset the counter each time the period is actually reached. Of course
the device offers much more possibilities.
For quadrature mode, both channel 0 and 1 must be configured even if we
only capture the position (no revolution/rotation).
Signed-off-by: Kamel Bouhara <kamel.bouhara@bootlin.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAl8UzA4eHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGQ7cH/3v+Gv+SmHJCvaT2
CSu0+7okVnYbY3UTb3hykk7/aOqb6284KjxR03r0CWFzsEsZVhC5pvvruASSiMQg
Pi04sLqv6CsGLHd1n+pl4AUYEaxq6k4KS3uU3HHSWxrahDDApQoRUx2F8lpOxyj8
RiwnoO60IMPA7IFJqzcZuFqsgdxqiiYvnzT461KX8Mrw6fyMXeR2KAj2NwMX8dZN
At21Sf8+LSoh6q2HnugfiUd/jR10XbfxIIx2lXgIinb15GXgWydEQVrDJ7cUV7ix
Jd0S+dtOtp+lWtFHDoyjjqqsMV7+G8i/rFNZoxSkyZqsUTaKzaR6JD3moSyoYZgG
0+eXO4A=
=9EpR
-----END PGP SIGNATURE-----
Merge 5.8-rc6 into staging-next
We need the staging fixes in here, and it resolves a merge issue with an
iio driver.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add lock protection from race conditions to the 104-quad-8 counter
driver for filter clock prescaler code changes. Mutex calls used for
protection.
Signed-off-by: Syed Nayyar Waris <syednwaris@gmail.com>
Fixes: de65d05563 ("counter: 104-quad-8: Support Filter Clock Prescaler")
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add lock protection from race conditions to 104-quad-8 counter driver
for differential encoder status code changes. Mutex lock calls used for
protection.
Signed-off-by: Syed Nayyar Waris <syednwaris@gmail.com>
Fixes: 954ab5cc5f ("counter: 104-quad-8: Support Differential Encoder Cable Status")
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Dharma Balasubiramani
William Breathitt Gray
William Breathitt Gray
Fabrice Gasnier
Jarkko Nikula
Greg Kroah-Hartman
Oleksij Rempel
David Lechner
Julia Lawall
Rikard Falkeborn
Dan Carpenter
Jonathan Cameron
Kamel Bouhara
Syed Nayyar Waris