If the only thing that is changing is SAGV vs. no SAGV but
the number of active planes and the total data rates end up
unchanged we currently bail out of intel_bw_atomic_check()
early and forget to actually compute the new WGV point
mask and thus won't actually enable/disable SAGV as requested.
This ends up poorly if we end up running with SAGV enabled
when we shouldn't. Usually ends up in underruns.
To fix this let's go through the QGV point mask computation
if either the data rates/number of planes, or the state
of SAGV is changing.
v2: Check more carefully if things are changing to avoid
the extra calculations/debugs from introducing unwanted
overhead
Cc: stable@vger.kernel.org
Reviewed-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com> #v1
Fixes: 20f505f225 ("drm/i915: Restrict qgv points which don't have enough bandwidth.")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220218064039.12834-3-ville.syrjala@linux.intel.com
(cherry picked from commit 6b728595ff)
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
When changing between SAGV vs. no SAGV on tgl+ we have to
update the use_sagv_wm flag for all the crtcs or else
an active pipe not already in the state will end up using
the wrong watermarks. That is especially bad when we end up
with the tighter non-SAGV watermarks with SAGV enabled.
Usually ends up in underruns.
Cc: stable@vger.kernel.org
Reviewed-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Fixes: 7241c57d31 ("drm/i915: Add TGL+ SAGV support")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220218064039.12834-2-ville.syrjala@linux.intel.com
(cherry picked from commit 8dd8ffb824)
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
BIOS may leave a TypeC PHY in a connected state even though the
corresponding port is disabled. This will prevent any hotplug events
from being signalled (after the monitor deasserts and then reasserts its
HPD) until the PHY is disconnected and so the driver will not detect a
connected sink. Rebooting with the PHY in the connected state also
results in a system hang.
Fix the above by disconnecting TypeC PHYs on disabled ports.
Before commit 64851a32c4 the PHY connected state was read out even
for disabled ports and later the PHY got disconnected as a side effect
of a tc_port_lock/unlock() sequence (during connector probing), hence
recovering the port's hotplug functionality.
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/5014
Fixes: 64851a32c4 ("drm/i915/tc: Add a mode for the TypeC PHY's disconnected state")
Cc: <stable@vger.kernel.org> # v5.16+
Cc: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220217152237.670220-1-imre.deak@intel.com
(cherry picked from commit ed0ccf349f)
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
adlp+ adds some extra bits to the QGV point mask. The code attempts
to handle that but forgot to actually make sure we can store those
bits in the bw state. Fix it.
Cc: stable@vger.kernel.org
Cc: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Fixes: 192fbfb767 ("drm/i915: Implement PSF GV point support")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220214091811.13725-4-ville.syrjala@linux.intel.com
Reviewed-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
(cherry picked from commit c0299cc984)
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Tejas reported the following recursive locking issue:
swapper/0/1 is trying to acquire lock:
ffff8881074fd0a0 (&md->mutex){+.+.}-{3:3}, at: msi_get_virq+0x30/0xc0
but task is already holding lock:
ffff8881017cd6a0 (&md->mutex){+.+.}-{3:3}, at: __pci_enable_msi_range+0xf2/0x290
stack backtrace:
__mutex_lock+0x9d/0x920
msi_get_virq+0x30/0xc0
pci_irq_vector+0x26/0x30
vmd_msi_init+0xcc/0x210
msi_domain_alloc+0xbf/0x150
msi_domain_alloc_irqs_descs_locked+0x3e/0xb0
__pci_enable_msi_range+0x155/0x290
pci_alloc_irq_vectors_affinity+0xba/0x100
pcie_port_device_register+0x307/0x550
pcie_portdrv_probe+0x3c/0xd0
pci_device_probe+0x95/0x110
This is caused by the VMD MSI code which does a lookup of the Linux
interrupt number for an VMD managed MSI[X] vector. The lookup function
tries to acquire the already held mutex.
Avoid that by caching the Linux interrupt number at initialization time
instead of looking it up over and over.
Fixes: 82ff8e6b78 ("PCI/MSI: Use msi_get_virq() in pci_get_vector()")
Reported-by: "Surendrakumar Upadhyay, TejaskumarX" <tejaskumarx.surendrakumar.upadhyay@intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: "Surendrakumar Upadhyay, TejaskumarX" <tejaskumarx.surendrakumar.upadhyay@intel.com>
Cc: linux-pci@vger.kernel.org
Link: https://lore.kernel.org/r/87a6euub2a.ffs@tglx
- Handle poisoned pages properly in the SGX reclaimer code
-----BEGIN PGP SIGNATURE-----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=5Bl4
-----END PGP SIGNATURE-----
Merge tag 'x86_urgent_for_v5.17_rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Borislav Petkov:
- Fix the ptrace regset xfpregs_set() callback to behave according to
the ABI
- Handle poisoned pages properly in the SGX reclaimer code
* tag 'x86_urgent_for_v5.17_rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/ptrace: Fix xfpregs_set()'s incorrect xmm clearing
x86/sgx: Fix missing poison handling in reclaimer
-----BEGIN PGP SIGNATURE-----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=EkNZ
-----END PGP SIGNATURE-----
Merge tag 'edac_urgent_for_v5.17_rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/ras/ras
Pull EDAC fix from Borislav Petkov:
"Fix a long-standing struct alignment bug in the EDAC struct allocation
code"
* tag 'edac_urgent_for_v5.17_rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/ras/ras:
EDAC: Fix calculation of returned address and next offset in edac_align_ptr()
Three fixes, all in drivers. The ufs and qedi fixes are minor; the
lpfc one is a bit bigger because it involves adding a heuristic to
detect and deal with common but not standards compliant behaviour.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCYhFMriYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishSAgAP49NgZf
qQfT/wk7sfrF2F1B6807hTPb6eY9CugBdBMU1wD9HsgeQRZ7JkYgoQGidzEGSuco
qrclT7ARGkJypFLFZNQ=
=jqv+
-----END PGP SIGNATURE-----
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Three fixes, all in drivers.
The ufs and qedi fixes are minor; the lpfc one is a bit bigger because
it involves adding a heuristic to detect and deal with common but not
standards compliant behaviour"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: ufs: core: Fix divide by zero in ufshcd_map_queues()
scsi: lpfc: Fix pt2pt NVMe PRLI reject LOGO loop
scsi: qedi: Fix ABBA deadlock in qedi_process_tmf_resp() and qedi_process_cmd_cleanup_resp()
Bunch of driver fixes for:
- ptdma error handling in init
- lock fix in at_hdmac
- error path and error num fix for sh dma
- pm balance fix for stm32
-----BEGIN PGP SIGNATURE-----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=5uHl
-----END PGP SIGNATURE-----
Merge tag 'dmaengine-fix-5.17' of git://git.kernel.org/pub/scm/linux/kernel/git/vkoul/dmaengine
Pull dmaengine fixes from Vinod Koul:
"A bunch of driver fixes for:
- ptdma error handling in init
- lock fix in at_hdmac
- error path and error num fix for sh dma
- pm balance fix for stm32"
* tag 'dmaengine-fix-5.17' of git://git.kernel.org/pub/scm/linux/kernel/git/vkoul/dmaengine:
dmaengine: shdma: Fix runtime PM imbalance on error
dmaengine: sh: rcar-dmac: Check for error num after dma_set_max_seg_size
dmaengine: stm32-dmamux: Fix PM disable depth imbalance in stm32_dmamux_probe
dmaengine: sh: rcar-dmac: Check for error num after setting mask
dmaengine: at_xdmac: Fix missing unlock in at_xdmac_tasklet()
dmaengine: ptdma: Fix the error handling path in pt_core_init()
Pull i2c fixes from Wolfram Sang:
"Some driver updates, a MAINTAINERS fix, and additions to COMPILE_TEST
(so we won't miss build problems again)"
* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
MAINTAINERS: remove duplicate entry for i2c-qcom-geni
i2c: brcmstb: fix support for DSL and CM variants
i2c: qup: allow COMPILE_TEST
i2c: imx: allow COMPILE_TEST
i2c: cadence: allow COMPILE_TEST
i2c: qcom-cci: don't put a device tree node before i2c_add_adapter()
i2c: qcom-cci: don't delete an unregistered adapter
i2c: bcm2835: Avoid clock stretching timeouts
Pull input fixes from Dmitry Torokhov:
- a fix for Synaptics touchpads in RMI4 mode failing to suspend/resume
properly because I2C client devices are now being suspended and
resumed asynchronously which changed the ordering
- a change to make sure we do not set right and middle buttons
capabilities on touchpads that are "buttonpads" (i.e. do not have
separate physical buttons)
- a change to zinitix touchscreen driver adding more compatible
strings/IDs
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: psmouse - set up dependency between PS/2 and SMBus companions
Input: zinitix - add new compatible strings
Input: clear BTN_RIGHT/MIDDLE on buttonpads
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQRAhzRXHqcMeLMyaSiRxhvAZXjcogUCYhDJyQAKCRCRxhvAZXjc
oqDZAP47lp7dQhndp5AuIsoeL/YIqbhFNfJ8hVUAcbFx/wJPFAEAtwXoeVXWT2ms
pU4nafoaQOpgsZJnD0UC5B/Pkr6laQ4=
=N5oo
-----END PGP SIGNATURE-----
Merge tag 'fs.mount_setattr.v5.17-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/brauner/linux
Pull mount_setattr test/doc fixes from Christian Brauner:
"This contains a fix for one of the selftests for the mount_setattr
syscall to create idmapped mounts, an entry for idmapped mounts for
maintainers, and missing kernel documentation for the helper we split
out some time ago to get and yield write access to a mount when
changing mount properties"
* tag 'fs.mount_setattr.v5.17-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/brauner/linux:
fs: add kernel doc for mnt_{hold,unhold}_writers()
MAINTAINERS: add entry for idmapped mounts
tests: fix idmapped mount_setattr test
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQRAhzRXHqcMeLMyaSiRxhvAZXjcogUCYhDKMgAKCRCRxhvAZXjc
opUwAPwORv7MD8rh5va7LFWUxX1UFpxVILWcC1umuhHAOKZ7YAEA3DTYFrQZhxA2
nMBR6hBEDKRARIFv3zHZYflYK97FnQA=
=NPXo
-----END PGP SIGNATURE-----
Merge tag 'pidfd.v5.17-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/brauner/linux
Pull pidfd fix from Christian Brauner:
"This fixes a problem reported by lockdep when installing a pidfd via
fd_install() with siglock and the tasklisk write lock held in
copy_process() when calling clone()/clone3() with CLONE_PIDFD.
Originally a pidfd was created prior to holding any of these locks but
this required a call to ksys_close(). So quite some time ago in
6fd2fe494b ("copy_process(): don't use ksys_close() on cleanups") we
switched to a get_unused_fd_flags() + fd_install() model.
As part of that we moved fd_install() as late as possible. This was
done for two main reasons. First, because we needed to ensure that we
call fd_install() past the point of no return as once that's called
the fd is live in the task's file table. Second, because we tried to
ensure that the fd is visible in /proc/<pid>/fd/<pidfd> right when the
task is visible.
This fix moves the fd_install() to an even later point which means
that a task will be visible in proc while the pidfd isn't yet under
/proc/<pid>/fd/<pidfd>.
While this is a user visible change it's very unlikely that this will
have any impact. Nobody should be relying on that and if they do we
need to come up with something better but again, it's doubtful this is
relevant"
* tag 'pidfd.v5.17-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/brauner/linux:
copy_process(): Move fd_install() out of sighand->siglock critical section
Pull ucounts fixes from Eric Biederman:
"Michal Koutný recently found some bugs in the enforcement of
RLIMIT_NPROC in the recent ucount rlimit implementation.
In this set of patches I have developed a very conservative approach
changing only what is necessary to fix the bugs that I can see
clearly. Cleanups and anything that is making the code more consistent
can follow after we have the code working as it has historically.
The problem is not so much inconsistencies (although those exist) but
that it is very difficult to figure out what the code should be doing
in the case of RLIMIT_NPROC.
All other rlimits are only enforced where the resource is acquired
(allocated). RLIMIT_NPROC by necessity needs to be enforced in an
additional location, and our current implementation stumbled it's way
into that implementation"
* 'ucount-rlimit-fixes-for-v5.17' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace:
ucounts: Handle wrapping in is_ucounts_overlimit
ucounts: Move RLIMIT_NPROC handling after set_user
ucounts: Base set_cred_ucounts changes on the real user
ucounts: Enforce RLIMIT_NPROC not RLIMIT_NPROC+1
rlimit: Fix RLIMIT_NPROC enforcement failure caused by capability calls in set_user
Michael Chan says:
====================
bnxt_en: Bug fixes
This series contains bug fixes for FEC reporting, ethtool self test,
multicast setup, devlink health reporting and live patching, and
a firmware response timeout.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
To install a livepatch, first flash the package to NVM, and then
activate the patch through the "HWRM_FW_LIVEPATCH" fw command.
To uninstall a patch from NVM, flash the removal package and then
activate it through the "HWRM_FW_LIVEPATCH" fw command.
The "HWRM_FW_LIVEPATCH" fw command has to consider following scenarios:
1. no patch in NVM and no patch active. Do nothing.
2. patch in NVM, but not active. Activate the patch currently in NVM.
3. patch is not in NVM, but active. Deactivate the patch.
4. patch in NVM and the patch active. Do nothing.
Fix the code to handle these scenarios during devlink "fw_activate".
To install and activate a live patch:
devlink dev flash pci/0000:c1:00.0 file thor_patch.pkg
devlink -f dev reload pci/0000:c1:00.0 action fw_activate limit no_reset
To remove and deactivate a live patch:
devlink dev flash pci/0000:c1:00.0 file thor_patch_rem.pkg
devlink -f dev reload pci/0000:c1:00.0 action fw_activate limit no_reset
Fixes: 3c4153394e ("bnxt_en: implement firmware live patching")
Reviewed-by: Vikas Gupta <vikas.gupta@broadcom.com>
Reviewed-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When polling for the firmware message response, we first poll for the
response message header. Once the valid length is detected in the
header, we poll for the valid bit at the end of the message which
signals DMA completion. Normally, this poll time for DMA completion
is extremely short (0 to a few usec). But on some devices under some
rare conditions, it can be up to about 20 msec.
Increase this delay to 50 msec and use udelay() for the first 10 usec
for the common case, and usleep_range() beyond that.
Also, change the error message to include the above delay time when
printing the timeout value.
Fixes: 3c8c20db76 ("bnxt_en: move HWRM API implementation into separate file")
Reviewed-by: Vladimir Olovyannikov <vladimir.olovyannikov@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During ifdown, we call bnxt_inv_fw_health_reg() which will clear
both the status_reliable and resets_reliable flags if these
registers are mapped. This is correct because a FW reset during
ifdown will clear these register mappings. If we detect that FW
has gone through reset during the next ifup, we will remap these
registers.
But during normal ifup with no FW reset, we need to restore the
resets_reliable flag otherwise we will not show the reset counter
during devlink diagnose.
Fixes: 8cc95ceb70 ("bnxt_en: improve fw diagnose devlink health messages")
Reviewed-by: Vikas Gupta <vikas.gupta@broadcom.com>
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Reviewed-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We should setup multicast only when net_device flags explicitly
has IFF_MULTICAST set. Otherwise we will incorrectly turn it on
even when not asked. Fix it by only passing the multicast table
to the firmware if IFF_MULTICAST is set.
Fixes: 7d2837dd7a ("bnxt_en: Setup multicast properly after resetting device.")
Signed-off-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the current code, we setup the port to PHY or MAC loopback mode
and then transmit a test broadcast packet for the loopback test. This
scheme fails sometime if the port is shared with management firmware
that can also send packets. The driver may receive the management
firmware's packet and the test will fail when the contents don't
match the test packet.
Change the test packet to use it's own MAC address as the destination
and setup the port to only receive it's own MAC address. This should
filter out other packets sent by management firmware.
Fixes: 91725d89b9 ("bnxt_en: Add PHY loopback to ethtool self-test.")
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Reviewed-by: Andy Gospodarek <gospo@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For offline (destructive) self tests, we need to stop the RDMA driver
first. Otherwise, the RDMA driver will run into unrecoverable errors
when destructive firmware tests are being performed.
The irq_re_init parameter used in the half close and half open
sequence when preparing the NIC for offline tests should be set to
true because the RDMA driver will free all IRQs before the offline
tests begin.
Fixes: 55fd0cf320 ("bnxt_en: Add external loopback test to ethtool selftest.")
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Reviewed-by: Ben Li <ben.li@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ethtool --show-fec <interface> does not show anything when the Active
FEC setting in the chip is set to None. Fix it to properly return
ETHTOOL_FEC_OFF in that case.
Fixes: 8b2775890a ("bnxt_en: Report FEC settings to ethtool.")
Signed-off-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
memblock.{reserved,memory}.regions may be allocated using kmalloc() in
memblock_double_array(). Use kfree() to release these kmalloced regions
indicated by memblock_{reserved,memory}_in_slab.
Signed-off-by: Miaohe Lin <linmiaohe@huawei.com>
Fixes: 3010f87650 ("mm: discard memblock data later")
Signed-off-by: Mike Rapoport <rppt@linux.ibm.com>
The sysfs does not like that we name the thermistor something
that contains a dash:
ntc-thermistor thermistor: hwmon: 'ssg1404-001221' is not a valid
name attribute, please fix
Fix it up by switching to an underscore.
Fixes: e13e979b2b ("hwmon: (ntc_thermistor) Add Samsung 1404-001221 NTC")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20220205005804.123245-1-linus.walleij@linaro.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
immediate verdict expression needs to allocate one slot in the flow offload
action array, however, immediate data expression does not need to do so.
fwd and dup expression need to allocate one slot, this is missing.
Add a new offload_action interface to report if this expression needs to
allocate one slot in the flow offload action array.
Fixes: be2861dc36 ("netfilter: nft_{fwd,dup}_netdev: add offload support")
Reported-and-tested-by: Nick Gregory <Nick.Gregory@Sophos.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
If the DSA master doesn't support IFF_UNICAST_FLT, then the following
call path is possible:
dsa_slave_switchdev_event_work
-> dsa_port_host_fdb_add
-> dev_uc_add
-> __dev_set_rx_mode
-> __dev_set_promiscuity
Since the blamed commit, dsa_slave_switchdev_event_work() no longer
holds rtnl_lock(), which triggers the ASSERT_RTNL() from
__dev_set_promiscuity().
Taking rtnl_lock() around dev_uc_add() is impossible, because all the
code paths that call dsa_flush_workqueue() do so from contexts where the
rtnl_mutex is already held - so this would lead to an instant deadlock.
dev_uc_add() in itself doesn't require the rtnl_mutex for protection.
There is this comment in __dev_set_rx_mode() which assumes so:
/* Unicast addresses changes may only happen under the rtnl,
* therefore calling __dev_set_promiscuity here is safe.
*/
but it is from commit 4417da668c ("[NET]: dev: secondary unicast
address support") dated June 2007, and in the meantime, commit
f1f28aa351 ("netdev: Add addr_list_lock to struct net_device."), dated
July 2008, has added &dev->addr_list_lock to protect this instead of the
global rtnl_mutex.
Nonetheless, __dev_set_promiscuity() does assume rtnl_mutex protection,
but it is the uncommon path of what we typically expect dev_uc_add()
to do. So since only the uncommon path requires rtnl_lock(), just check
ahead of time whether dev_uc_add() would result into a call to
__dev_set_promiscuity(), and handle that condition separately.
DSA already configures the master interface to be promiscuous if the
tagger requires this. We can extend this to also cover the case where
the master doesn't handle dev_uc_add() (doesn't support IFF_UNICAST_FLT),
and on the premise that we'd end up making it promiscuous during
operation anyway, either if a DSA slave has a non-inherited MAC address,
or if the bridge notifies local FDB entries for its own MAC address, the
address of a station learned on a foreign port, etc.
Fixes: 0faf890fc5 ("net: dsa: drop rtnl_lock from dsa_slave_switchdev_event_work")
Reported-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit b3612ccdf2 ("net: dsa: microchip: implement multi-bridge support")
plugged a packet leak between ports that were members of different bridges.
Unfortunately, this broke another use case, namely that of more than two
ports that are members of the same bridge.
After that commit, when a port is added to a bridge, hardware bridging
between other member ports of that bridge will be cleared, preventing
packet exchange between them.
Fix by ensuring that the Port VLAN Membership bitmap includes any existing
ports in the bridge, not just the port being added.
Fixes: b3612ccdf2 ("net: dsa: microchip: implement multi-bridge support")
Signed-off-by: Svenning Sørensen <sss@secomea.com>
Tested-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2022-02-18
This series contains updates to ice driver only.
Wojciech fixes protocol matching for slow-path switchdev so that all
packets are correctly redirected.
Michal removes accidental unconditional setting of l4 port filtering
flag.
Jake adds locking to protect VF reset and removal to fix various issues
that can be encountered when they race with each other.
Tom Rix propagates an error and initializes a struct to resolve reported
Clang issues.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Mat Martineau says:
====================
mptcp: Fix address advertisement races and stabilize tests
Patches 1, 2, and 7 modify two self tests to give consistent, accurate
results by fixing timing issues and accounting for syncookie behavior.
Paches 3-6 fix two races in overlapping address advertisement send and
receive. Associated self tests are updated, including addition of two
MIBs to enable testing and tracking dropped address events.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit 2843ff6f36 ("mptcp: remote addresses fullmesh"), an
MPTCP client can attempt creating multiple MPJ subflow simultaneusly.
In such scenario the server, when syncookies are enabled, could end-up
accepting incoming MPJ syn even above the configured subflow limit, as
the such limit can be enforced in a reliable way only after the subflow
creation. In case of syncookie, only after the 3rd ack reception.
As a consequence the related self-tests case sporadically fails, as it
verify that the server always accept the expected number of MPJ syn.
Address the issues relaxing the MPJ syn number constrain. Note that the
check on the accepted number of MPJ 3rd ack still remains intact.
Fixes: 2843ff6f36 ("mptcp: remote addresses fullmesh")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The in kernel MPTCP PM implementation can process a single
incoming add address option at any given time. In the
mentioned test the server can surpass such limit. Let the
setup cope with that allowing a faster add_addr retransmission.
Fixes: a88c9e4969 ("mptcp: do not block subflows creation on errors")
Fixes: f7efc7771e ("mptcp: drop argument port from mptcp_pm_announce_addr")
Closes: https://github.com/multipath-tcp/mptcp_net-next/issues/254
Reported-and-tested-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Reviewed-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MPTCP in kernel path manager has some constraints on incoming
addresses announce processing, so that in edge scenarios it can
end-up dropping (ignoring) some of such announces.
The above is not very limiting in practice since such scenarios are
very uncommon and MPTCP will recover due to ADD_ADDR retransmissions.
This patch adds a few MIB counters to account for such drop events
to allow easier introspection of the critical scenarios.
Fixes: f7efc7771e ("mptcp: drop argument port from mptcp_pm_announce_addr")
Reviewed-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If an MPTCP endpoint received multiple consecutive incoming
ADD_ADDR options, mptcp_pm_add_addr_received() can overwrite
the current remote address value after the PM lock is released
in mptcp_pm_nl_add_addr_received() and before such address
is echoed.
Fix the issue caching the remote address value a little earlier
and always using the cached value after releasing the PM lock.
Fixes: f7efc7771e ("mptcp: drop argument port from mptcp_pm_announce_addr")
Reviewed-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After commit a88c9e4969 ("mptcp: do not block subflows
creation on errors"), if a signal address races with a failing
subflow creation, the subflow creation failure control path
can trigger the selection of the next address to be announced
while the current announced is still pending.
The above will cause the unintended suppression of the ADD_ADDR
announce.
Fix the issue skipping the to-be-suppressed announce before it
will mark an endpoint as already used. The relevant announce
will be triggered again when the current one will complete.
Fixes: a88c9e4969 ("mptcp: do not block subflows creation on errors")
Reviewed-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mentioned test has to wait for a subflow creation failure.
The current code looks for TCP sockets in TW state and sometimes
misses the relevant event. Switch to a more stable check, looking
for the associated mib counter.
Fixes: 46e967d187 ("selftests: mptcp: add tests for subflow creation failure")
Closes: https://github.com/multipath-tcp/mptcp_net-next/issues/257
Reported-and-tested-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of waiting for an arbitrary amount of time for the MPTCP
MP_CAPABLE handshake to complete, explicitly wait for the relevant
socket to enter into the established status.
Additionally let the data transfer application use the slowest
transfer mode available (-r), to cope with very slow host, or
high jitter caused by hosting VMs.
Fixes: df62f2ec3d ("selftests/mptcp: add diag interface tests")
Closes: https://github.com/multipath-tcp/mptcp_net-next/issues/258
Reported-and-tested-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver is already covered in the ARM/QUALCOMM section. Also, Akash
Asthana's email bounces meanwhile and Mukesh Savaliya has never
responded to mails regarding this driver.
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Where commit 4ef0c5c6b5 ("kernel/sched: Fix sched_fork() access an
invalid sched_task_group") fixed a fork race vs cgroup, it opened up a
race vs syscalls by not placing the task on the runqueue before it
gets exposed through the pidhash.
Commit 13765de814 ("sched/fair: Fix fault in reweight_entity") is
trying to fix a single instance of this, instead fix the whole class
of issues, effectively reverting this commit.
Fixes: 4ef0c5c6b5 ("kernel/sched: Fix sched_fork() access an invalid sched_task_group")
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Tested-by: Tadeusz Struk <tadeusz.struk@linaro.org>
Tested-by: Zhang Qiao <zhangqiao22@huawei.com>
Tested-by: Dietmar Eggemann <dietmar.eggemann@arm.com>
Link: https://lkml.kernel.org/r/YgoeCbwj5mbCR0qA@hirez.programming.kicks-ass.net
ida_simple_get() returns an id between min (0) and max (NFP_MAX_MAC_INDEX)
inclusive.
So NFP_MAX_MAC_INDEX (0xff) is a valid id.
In order for the error handling path to work correctly, the 'invalid'
value for 'ida_idx' should not be in the 0..NFP_MAX_MAC_INDEX range,
inclusive.
So set it to -1.
Fixes: 20cce88650 ("nfp: flower: enable MAC address sharing for offloadable devs")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/20220218131535.100258-1-simon.horman@corigine.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
* Revert misplaced ID
The following is an automated git shortlog grouped by driver:
tigerlake:
- Revert "Add Alder Lake-M ACPI ID"
-----BEGIN PGP SIGNATURE-----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=Rr8/
-----END PGP SIGNATURE-----
Merge tag 'intel-pinctrl-v5.17-5' of gitolite.kernel.org:pub/scm/linux/kernel/git/pinctrl/intel into fixes
intel-pinctrl for v5.17-5
* Revert misplaced ID
The following is an automated git shortlog grouped by driver:
tigerlake:
- Revert "Add Alder Lake-M ACPI ID"
Ville Syrjälä
Imre Deak
Daniele Palmas
Slark Xiao
Dmytro Bagrii
Thomas Gleixner
Linus Torvalds
David S. Miller
Kalesh AP
Michael Chan
Pavan Chebbi
Somnath Kotur
Miaohe Lin
Linus Walleij
Pablo Neira Ayuso
Vladimir Oltean
Svenning Sørensen
Christophe Leroy
Paolo Abeni
Wolfram Sang
Peter Zijlstra
Christophe JAILLET
Subash Abhinov Kasiviswanathan
Jeremy Linton