If a touchscreen contains both multitouch and single-touch reports in its
descriptor in that order, the driver may overwrite information it saved
about the format of the multitouch report. This can cause the report
processing code to get tripped up and send an incorrect event stream to
userspace.
In particular, this can cause last_slot_field to be overwritten with the
result that the driver prematurely assumes it has finished processing a
slot and sending the ABS_MT_SLOT event at the wrong point in time,
associating events for the current contact with the following contact
instead.
To prevent this from occurring, we update the value of last_slot_field
durring the pre_report phase to ensure that it is correct for the report
that is to be processed.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Reviewed-by: Ping Cheng <pingc@wacom.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
"Direct" input devices like Cintiqs and Tablet PCs set the INPUT_PROP_DIRECT
property to notify userspace that the sensor and screen are overlaid. This
information can also be useful elsewhere within the kernel driver, however,
so we introduce a new WACOM_DEVICETYPE_DIRECT that signals this to other
kernel code.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Instead of displaying a generic "tablet", now g-c-c shows a pretty
"Wacom Intuos Pro S (WL)".
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Previously, all the remotes attached to the same receiver would share the
same power_supply. That's not good as the remotes will constantly change
the battery information according to their own state.
To have something generic enough, we introduce struct wacom_battery
which regroups all the information we need for a battery.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
If we want to have one input device per remote, it's better to have our
own struct wacom_remote which is dynamically allocated.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
wacom_remote_status_irq() sends information of addition/removal of EKR.
We want to allocate one input node per remote, so better having this
in a separate worker, not handled in the IRQ directly.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
We currently have a complex clean_inputs() function while this can be
handled all by devres. Set a group that we can destroy in wireless_work().
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The fuzz present on the distance and tilt axes is noticable when a puck is
present, and userspace (specifically libinput) would like the ability to
filter out the noise. To facilitate this, we assign a fuzz value of '1'
for the distance and tilt axes. This is large enough to cover most of the
natural variation in distance value as the puck is moved around, and
enough to cover the jitter in rotation (reported through tilt axes) when
the puck is left alone.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
A tablet PC booted into Windows may have its pen/touch hardware switched
into "Wacom mode" similar to what we do with explicitly-supported hardware.
Some devices appear to maintain this state across reboots, preventing their
use with the generic HID driver. This patch adds support for detecting the
presence of the mode switch feature report used by devices based on the G9
and G11 chips and has the HID codepath always attempt to reset the device
back to sending standard HID reports.
Fixes: https://sourceforge.net/p/linuxwacom/bugs/307/
Fixes: https://sourceforge.net/p/linuxwacom/bugs/310/
Fixes: https://github.com/linuxwacom/input-wacom/issues/15
Co-authored-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Unlike other tablets which are compatible with the wacom_intuos_irq handler,
INTUOSHT2 devices provide pen ID with report ID 8 instead of 5. To ensure
wacom_intuos_schedule_prox_event works as intended for these tablets, we
must be sure it uses the correct report ID in this case.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
"INTUOSREAD" and "INTUOSWRITE" are poorly named. These are report IDs
for pen ID (proximity) packets. It should be noted that the latter is
only used on Intuos/Intuos2 for a second stylus when DualTrack is in use.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Intuos Pen in wireless mode does not have the same report id (2) as
when it is in USB mode (17).
This patch also moves WIRELESS next to REMOTE in type enum so we
can group devices with similar features easily.
Reported-by: Dale Brewe <dlbrewe@hotmail.com>
Tested-by: Dale Brewe <dlbrewe@hotmail.com>
Signed-off-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The cached indicies 'cc_index' and 'cc_value_index' introduced in 1b5d514
are only valid for a single report ID. If a touchscreen has multiple
reports with a HID_DG_CONTACTCOUNT usage, its possible that the values
will not be correct for the report we're handling, resulting in an
incorrect value for 'num_expected'. This has been observed with the Cintiq
Companion 2.
To address this, we store the ID of the report those indicies are valid
for in a new 'cc_report' variable. Before using them to get the expected
contact count, we first check if the ID of the report we're processing
matches 'cc_report'. If it doesn't, we update the indicies to point to
the HID_DG_CONTACTCOUNT usage of the current report (if it has one).
Cc: stable@vger.kernel.org
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Adds support for the EMR (pen+pad) and touchscreen devices used by the
Wacom Cintiq Companion 2. This applies both to using the device as a
standalone system, as well as when operating in "Cintiq mode" (where
the EMR/touchscreen are simply exposed as USB devices to the system
its connected to).
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Clifford Jolly <expiredpopsicle@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This series of devices supports both pen and touch. It reports
touch data in Bamboo3 format and pen data in Intuos pro format.
Signed-off-by: Ping Cheng <pingc@wacom.com>
Tested-By: Aaron Skomra <aaron.skomra@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Not all Bamboo support both pen and touch. Make sure we deal with
pen only and touch only devices properly.
Signed-off-by: Ping Cheng <pingc@wacom.com>
Tested-By: Aaron Skomra <aaron.skomra@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This device is pad (buttons) only, there is no stylus or touch. Up to
five remotes can pair with the device's associated USB dongle.
Signed-off-by: Aaron Skomra <aaron.skomra@wacom.com>
Reviewed-by: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Prior to this commit, numbered button bit setting was done separately
for each device type in wacom_setup_pad_capabilities(). Here we add a
numbered_buttons property to the wacom_features struct and extract the
repeated bit setting code to a new function:
wacom_settup_numbered_buttons().
Signed-off-by: Aaron Skomra <aaron.skomra@wacom.com>
Reviewed-by: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
WACOM_QUIRK_NO_INPUT is a signal to the driver that input devices
should not be created for a particular device. This quirk was used by
the wireless receiver to prevent any devices from being created during
the initial probe (defering it instead until we got a tablet connection
event in 'wacom_wireless_work').
This quirk is not necessary now that a device_type is associated with each
device. Any input device allocated by 'wacom_allocate_inputs' which is
not necessary for a particular device is freed in 'wacom_register_inputs'.
In particular, none of the wireless receivers devices have the pen, pad,
or touch device types set so the same effect is achieved without the need
to be explicit.
We now return early in wacom_retrieve_hid_descriptor for wireless devices
(to prevent the device_type from being overridden) but since we ignore the
HID descriptor for the wireless reciever anyway, this is not an issue.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
The monitor interface on the wireless receiver is more logically expressed
as a type of device instead of a quirk.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
The reports sent from some touch devices (e.g. the Cintiq 24HDT) contain
junk data in the contact slots which follow the final "valid" contact.
To avoid forwarding it to usrspace, we store the reported contact count
during the pre-process phase and then only process that many contacts.
If a device sends its contacts across multiple reports (what Microsoft
refers to as "hybrid" mode) then the contact count will be zero for
reports other than the first.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
Instead of having a single 'input_dev' device that will take either pen
or touch data depending on the type of the device, create seperate devices
devices for each. By splitting things like this, we can support devices
(e.g. the I2C "AES" sensors in some newer tablet PCs) that send both pen
and touch reports from a single endpoint.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Historically, both the touch and pad tools would have shared the
'BTN_TOOL_FINGER' type. Any time you needed to distinguish the two, you
had to use some other bit of knowledge (e.g. that the pad was on the same
interface as the pen, and thus 'touch_max' would be zero).
To make these checks more readable, we introduce WACOM_DEVICETYPE_PAD.
Although we still have to rely on other bits of knowledge to set this
bit on the right interface (since it cannot be detected from the HID
descriptor), it can be done just once inside 'wacom_setup_device_quirks'.
This patch introduces no functional changes.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The USB devices that this driver has historically supported segregate the
pen and touch portions of the tablet. Oftentimes the segregation would be
done at the interface level, though on occasion (e.g. Cintiq 24HDT) the
tablet would combine two totally independent USB devices behind an internal
USB hub. Because pen and touch never shared the same interface, it made
sense for the 'device_type' to store a single value: "pen" or "touch".
Recently, however, some I2C devices have been created which combine the
two. A first step to accomodating this is to expand 'device_type' so that
it can represent two (or potentially more) types simultaneously. To do
this, we treat it as a bitfield and set/check individual bits rather
than using the '=' and '==' operators.
This should not result in any functional change since no supported devices
(that I'm aware of, at least) have HID descriptors that indicate both
pen and touch reports on a single interface.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Currently, we assume a device_type of BTN_TOOL_PEN before scanning the
HID descriptor and then change the device_type if what we discover
proves that assumption wrong. This way of doing things makes it more
difficult to figure out if a device (particularly a HID_GENERIC device)
actually does tablet/touch input or is something completley different.
This patch leaves device_type at its initial value of 0 and then calls
'wacom_parse_hid' for every device (not just those that have touch).
As we map the usages, we can set the device_type as before. After we're
finished, we can then check if the value is still zero and do whatever
is most appropriate.
Detecting the pen can be a little tricky on most Wacom devices because
the descriptors describe opaque blobs. Fortunately, older Wacom tablets
have the HID_DG_DIGITIZER usage on the pen's application collection and
newer tablets seem to have a similar vendor-defined usage that we can
trigger on.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Reviewed-by: Ping Cheng <pingc@wacom.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
We use generic hid_report_len() to get individual packet length now.
Signed-off-by: Ping Cheng <pingc@wacom.com>
Reviewed-by: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The quirk was added for devices that support both pen and touch. It decides if
a device supports multiple inputs by hardcoded feature type. However, for some
devices, we do not know if they support both before accessing their HID
descriptors.
This patch relies on dynamically assigned device_type to make the decision.
Also, we make it certain that wacom_wac->shared is always created. That is, the
driver will not be loaded if it fails to create wacom_wac->shared.
Signed-off-by: Ping Cheng <pingc@wacom.com>
Reviewed-by: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Declare the POWER_SUPPLY_PROP_PRESENT property to provide userspace
with a way to determine if the battery on a wireless tablet is plugged
in. Although current wireless tablets do not explicitly report this
information, it can be inferred from other state information. In
particular, a battery is assumed to be present if any of the following
are true: a non-zero battery level reported, the battery is reported as
charging, or the tablet is operating wirelessly.
Note: The last condition above may not strictly hold for the Graphire
Wireless (it charges from a DC barrel jack instead of a USB port), but I
do not know what is reported in the no-battery condition.
Signed-off-by: Jason Gerecke <killertofu@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The constant is not used (leftover from previous patch versions
that never got merged).
Reported-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
In addition to the touchswitch state for "Intuos", these packets are
also sent by the Intuos Pro, Intuos5, and last-generation Bamboo
tablets when using a wired connection. They contain, among other
things, information about the optional wireless module and battery
charge state (to be supported in subsuquent patches).
Signed-off-by: Jason Gerecke <killertofu@gmail.com>
Acked-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The stylus of this device works just fine out of the box.
The touch is seen by default as a mouse with relative events and some
gestures.
The wireless and the wired version have slightly different firmwares, but
the debug mode 2 on the feature 2 is common to the 2 devices. In this mode,
all the reports are emitted through the debug interface (pen, raw touch
and mouse emulation), so we have to re-route manually the events.
We keep the Pen interface as a HID_GENERIC one because it works, and only
parse the raw touches while discarding the mouse emulation & gestures.
Switching the default in raw mode allows us to have a consistent user
experience accross all the multitouch touchpads (and enable the touch part
of the devices).
Note that the buttons of this devices are reported through the touch
interface. There is no 'Pad' interface. It seemed more natural to have
the BTN_LEFT and BTN_RIGHT reported with the touch because they are
placed under the touch interface and it looks like they belong to the
touch part.
Tested-by: Josep Sanchez Ferreres <josep.sanchez.ferreres@est.fib.upc.edu>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The Bamboo PAD in debug mode needs to re-route events from the debug
interface to the Pen interface. This can be easily done with
hid_input_report(), but that means that we need to keep a reference to
the various hid_devices.
There should be only one touch and one pen interface per physical tablet,
so there is no need to keep a list of hid-devices, plain pointers are
sufficient.
Tested-by: Josep Sanchez Ferreres <josep.sanchez.ferreres@est.fib.upc.edu>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
These devices have accelerometers. To report accelerometer coordinates, a new
property, INPUT_PROP_ACCELEROMETER, is added.
Signed-off-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Some Cintiq and Intuos tablets report In Range event. This event is sent before
valid data is reported when tool enters proximity; or before out of proximity
event is reported when tool exits.
While entering proximity, In Range means a pen is detected. This information
can be used for palm/touch rejection on both pen and touch enabled devices.
While exiting, it means the tool has reached its maximum detectable distance.
Signed-off-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Bamboo Pads are using the generic processing but their report descriptors
differ from the ISDv* line. The pen fields are marked with the .physical
as Digitizer_Pen, which makes also sense.
Add this field to the checks and enable for free Bamboo Pads.
Reported-by: Josep Sanchez Ferreres <josep.sanchez.ferreres@est.fib.upc.edu>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Reviewed-by: Jason Gerecke <killertofu@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
We introduced nice macros in wacom_wac.c to check whether a field is
a pen or a touch one.
wacom_usage_mapping() still uses it's own tests, which are not in sync with
the wacom_wac tests (.application is not checked).
That means that some legitimate fields might be filtered out from the
usage mapping, and thus will not be used properly while receiving the
events.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The existing generic touch code only reports events after reading an
entire HID report, which practically means that only data about the last
contact in a report will ever be provided to userspace. This patch uses
a trick from hid-multitouch.c to discover what type of field is at the
end of each contact; when such a field is encountered all the stored
contact data will be reported.
Signed-off-by: Jason Gerecke <killertofu@gmail.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
PAD can be on pen interface (Intuos Pro and Cintiq series) or touch
interface (Bamboo PT and Intuos PT series) or its own interface
(Bamboo pen-only and Intuos Pen M/S). We need to mark it independently.
Signed-off-by: Ping Cheng <pingc@wacom.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
ISDv4 and v5 are plain HID devices. We can directly implement a generic
HID parsing/handling and remove the need to manually add those PID in
the list of supported devices.
This patch implements the pen support only. The finger part will come in
a later patch.
To be properly notified of an .event() and a .report(), we need to force
hid-core to go through the HID parsing. By default, wacom.ko binds only
hidraw, so the hid parsing is not done by hid-core. When a true HID device
is there, we add the flag HID_CLAIMED_DRIVER to hid->claimed which will
force hid-core to parse the incoming reports.
(Note that this can be easily backported by directly setting the .claimed
flag to HID_CLAIMED_DRIVER even if hid-core does not support
HID_CONNECT_DRIVER)
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Jason Gerecke <killertofu@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
If the input can be created earlier during probe, we can already populate
them while reading the report descriptor. This way, we can rely on the
hid subsystem directly for tablets which already provide a meaningful
report descriptor (like ISDv4-5).
This patch only splits the allocation and registration, but do not
change where we allocate the input. This will come in a later patch.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Jason Gerecke <killertofu@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
A good point of this change is that now, the Intuos4 bluetooth can handle
the different tools (artpen, airbrush, mice), and we get a common interface
between USB and BT for accessing the LEDs/OLEDs.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Reviewed-by: Ping Cheng <pingc@wacom.com>
Tested-by: Przemo Firszt <przemo@firszt.eu>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Now that wacom is a hid driver, there is no point in having a separate
driver for bluetooth devices. This patch prepares the common paths of
Bluetooth devices in the common wacom driver. It also adds the sysfs file
"speed" used by Bluetooth devices.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Reviewed-by: Ping Cheng <pingc@wacom.com>
Tested-by: Przemo Firszt <przemo@firszt.eu>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This is used by HID Bluetooth devices but also add some more information
to the USB Wireless Receiver.
We are just porting the bits from hid-wacom.c to the common driver here.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Przemo Firszt <przemo@firszt.eu>
Acked-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The current implementation uses "wacom_battery" as a generic name for
batteries. This prevents us to have two Wacom devices with a battery
attached as the power system will complain about the name which is already
registered.
Use an incremental name for each battery attached.
Related bug:
https://sourceforge.net/p/linuxwacom/bugs/248/
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Przemo Firszt <przemo@firszt.eu>
Acked-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
- Reports the current status of the battery (discharging, charging, full).
- Also notify the upower daemon when there is a change in the battery
value.
- keep the battery value as a percentage, not the raw value
- add WACOM_QUIRK_BATTERY to easily add a battery to a device (required
for Bluetooth devices)
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Przemo Firszt <przemo@firszt.eu>
Acked-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Jiri Kosina
Jason Gerecke
Benjamin Tissoires
Ping Cheng
Aaron Skomra