Commit f1b8274 ("clocksource: Cleanup clocksource selection") removed all
external references to clocksource_jiffies so there is no need to have the
symbol globally visible.
Fixes the following sparse warning:
CHECK kernel/time/jiffies.c kernel/time/jiffies.c:61:20: warning: symbol 'clocksource_jiffies' was not declared. Should it be static?
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: John Stultz <john.stultz@linaro.org>
This patch removes the timecompare code from the kernel. The top five
reasons to do this are:
1. There are no more users of this code.
2. The original idea was a bit weak.
3. The original author has disappeared.
4. The code was not general purpose but tuned to a particular hardware,
5. There are better ways to accomplish clock synchronization.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Acked-by: John Stultz <john.stultz@linaro.org>
Tested-by: Bob Liu <lliubbo@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the comments of function tick_sched_timer(), the sentence
"timer->base->cpu_base->lock held" is not right.
In function __run_hrtimer(), before call timer->function(),
the cpu_base->lock has been unlocked.
Signed-off-by: liu chuansheng <chuansheng.liu@intel.com>
Cc: fei.li@intel.com
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/1351098455.15558.1421.camel@cliu38-desktop-build
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
In the comments of function tick_sched_timer(), the sentence
"timer->base->cpu_base->lock held" is not right.
In function __run_hrtimer(), before call timer->function(),
the cpu_base->lock has been unlocked.
Signed-off-by: liu chuansheng <chuansheng.liu@intel.com>
Cc: fei.li@intel.com
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/1351098455.15558.1421.camel@cliu38-desktop-build
Signed-off-by: Ingo Molnar <mingo@kernel.org>
This optimize a bit the high res tick sched handler.
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Besides unifying code, this also adds the idle check before
processing idle accounting specifics on the low res handler.
This way we also generalize this part of the nohz code for
!CONFIG_HIGH_RES_TIMERS to prepare for the adaptive tickless
features.
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Unify the duplicated timekeeping handling code of low and high res tick
sched handlers.
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Pull timer core update from Thomas Gleixner:
- Bug fixes (one for a longstanding dead loop issue)
- Rework of time related vsyscalls
- Alarm timer updates
- Jiffies updates to remove compile time dependencies
* 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
timekeeping: Cast raw_interval to u64 to avoid shift overflow
timers: Fix endless looping between cascade() and internal_add_timer()
time/jiffies: bring back unconditional LATCH definition
time: Convert x86_64 to using new update_vsyscall
time: Only do nanosecond rounding on GENERIC_TIME_VSYSCALL_OLD systems
time: Introduce new GENERIC_TIME_VSYSCALL
time: Convert CONFIG_GENERIC_TIME_VSYSCALL to CONFIG_GENERIC_TIME_VSYSCALL_OLD
time: Move update_vsyscall definitions to timekeeper_internal.h
time: Move timekeeper structure to timekeeper_internal.h for vsyscall changes
jiffies: Remove compile time assumptions about CLOCK_TICK_RATE
jiffies: Kill unused TICK_USEC_TO_NSEC
alarmtimer: Rename alarmtimer_remove to alarmtimer_dequeue
alarmtimer: Remove unused helpers & defines
alarmtimer: Use hrtimer per-alarm instead of per-base
alarmtimer: Implement minimum alarm interval for allowing suspend
Pull scheduler fixes from Ingo Molnar:
"A CPU hotplug related crash fix and a nohz accounting fixlet."
* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched: Update sched_domains_numa_masks[][] when new cpus are onlined
sched: Ensure 'sched_domains_numa_levels' is safe to use in other functions
nohz: Fix one jiffy count too far in idle cputime
We fixed a bunch of integer overflows in timekeeping code during the 3.6
cycle. I did an audit based on that and found this potential overflow.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: John Stultz <johnstul@us.ibm.com>
Link: http://lkml.kernel.org/r/20121009071823.GA19159@elgon.mountain
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org
When we stop the tick in idle, we save the current jiffies value
in ts->idle_jiffies. This snapshot is substracted from the later
value of jiffies when the tick is restarted and the resulting
delta is accounted as idle cputime. This is how we handle the
idle cputime accounting without the tick.
But sometimes we need to schedule the next tick to some time in
the future instead of completely stopping it. In this case, a
tick may happen before we restart the periodic behaviour and
from that tick we account one jiffy to idle cputime as usual but
we also increment the ts->idle_jiffies snapshot by one so that
when we compute the delta to account, we substract the one jiffy
we just accounted.
To prepare for stopping the tick outside idle, we introduced a
check that prevents from fixing up that ts->idle_jiffies if we
are not running the idle task. But we use idle_cpu() for that
and this is a problem if we run the tick while another CPU
remotely enqueues a ttwu to our runqueue:
CPU 0: CPU 1:
tick_sched_timer() { ttwu_queue_remote()
if (idle_cpu(CPU 0))
ts->idle_jiffies++;
}
Here, idle_cpu() notes that &rq->wake_list is not empty and
hence won't consider the CPU as idle. As a result,
ts->idle_jiffies won't be incremented. But this is wrong because
we actually account the current jiffy to idle cputime. And that
jiffy won't get substracted from the nohz time delta. So in the
end, this jiffy is accounted twice.
Fix this by changing idle_cpu(smp_processor_id()) with
is_idle_task(current). This way the jiffy is substracted
correctly even if a ttwu operation is enqueued on the CPU.
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: <stable@vger.kernel.org> # 3.5+
Link: http://lkml.kernel.org/r/1349308004-3482-1-git-send-email-fweisbec@gmail.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
* Improved system suspend/resume and runtime PM handling for the SH TMU, CMT
and MTU2 clock event devices (also used by ARM/shmobile).
* Generic PM domains framework extensions related to cpuidle support and
domain objects lookup using names.
* ARM/shmobile power management updates including improved support for the
SH7372's A4S power domain containing the CPU core.
* cpufreq changes related to AMD CPUs support from Matthew Garrett, Andre
Przywara and Borislav Petkov.
* cpu0 cpufreq driver from Shawn Guo.
* cpufreq governor fixes related to the relaxing of limit from Michal Pecio.
* OMAP cpufreq updates from Axel Lin and Richard Zhao.
* cpuidle ladder governor fixes related to the disabling of states from
Carsten Emde and me.
* Runtime PM core updates related to the interactions with the system suspend
core from Alan Stern and Kevin Hilman.
* Wakeup sources modification allowing more helper functions to be called from
interrupt context from John Stultz and additional diagnostic code from Todd
Poynor.
* System suspend error code path fix from Feng Hong.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)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=rbCk
-----END PGP SIGNATURE-----
Merge tag 'pm-for-3.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management updates from Rafael J Wysocki:
- Improved system suspend/resume and runtime PM handling for the SH
TMU, CMT and MTU2 clock event devices (also used by ARM/shmobile).
- Generic PM domains framework extensions related to cpuidle support
and domain objects lookup using names.
- ARM/shmobile power management updates including improved support for
the SH7372's A4S power domain containing the CPU core.
- cpufreq changes related to AMD CPUs support from Matthew Garrett,
Andre Przywara and Borislav Petkov.
- cpu0 cpufreq driver from Shawn Guo.
- cpufreq governor fixes related to the relaxing of limit from Michal
Pecio.
- OMAP cpufreq updates from Axel Lin and Richard Zhao.
- cpuidle ladder governor fixes related to the disabling of states from
Carsten Emde and me.
- Runtime PM core updates related to the interactions with the system
suspend core from Alan Stern and Kevin Hilman.
- Wakeup sources modification allowing more helper functions to be
called from interrupt context from John Stultz and additional
diagnostic code from Todd Poynor.
- System suspend error code path fix from Feng Hong.
Fixed up conflicts in cpufreq/powernow-k8 that stemmed from the
workqueue fixes conflicting fairly badly with the removal of support for
hardware P-state chips. The changes were independent but somewhat
intertwined.
* tag 'pm-for-3.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (76 commits)
Revert "PM QoS: Use spinlock in the per-device PM QoS constraints code"
PM / Runtime: let rpm_resume() succeed if RPM_ACTIVE, even when disabled, v2
cpuidle: rename function name "__cpuidle_register_driver", v2
cpufreq: OMAP: Check IS_ERR() instead of NULL for omap_device_get_by_hwmod_name
cpuidle: remove some empty lines
PM: Prevent runtime suspend during system resume
PM QoS: Use spinlock in the per-device PM QoS constraints code
PM / Sleep: use resume event when call dpm_resume_early
cpuidle / ACPI : move cpuidle_device field out of the acpi_processor_power structure
ACPI / processor: remove pointless variable initialization
ACPI / processor: remove unused function parameter
cpufreq: OMAP: remove loops_per_jiffy recalculate for smp
sections: fix section conflicts in drivers/cpufreq
cpufreq: conservative: update frequency when limits are relaxed
cpufreq / ondemand: update frequency when limits are relaxed
properly __init-annotate pm_sysrq_init()
cpufreq: Add a generic cpufreq-cpu0 driver
PM / OPP: Initialize OPP table from device tree
ARM: add cpufreq transiton notifier to adjust loops_per_jiffy for smp
cpufreq: Remove support for hardware P-state chips from powernow-k8
...
Pull scheduler changes from Ingo Molnar:
"Continued quest to clean up and enhance the cputime code by Frederic
Weisbecker, in preparation for future tickless kernel features.
Other than that, smallish changes."
Fix up trivial conflicts due to additions next to each other in arch/{x86/}Kconfig
* 'sched-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (24 commits)
cputime: Make finegrained irqtime accounting generally available
cputime: Gather time/stats accounting config options into a single menu
ia64: Reuse system and user vtime accounting functions on task switch
ia64: Consolidate user vtime accounting
vtime: Consolidate system/idle context detection
cputime: Use a proper subsystem naming for vtime related APIs
sched: cpu_power: enable ARCH_POWER
sched/nohz: Clean up select_nohz_load_balancer()
sched: Fix load avg vs. cpu-hotplug
sched: Remove __ARCH_WANT_INTERRUPTS_ON_CTXSW
sched: Fix nohz_idle_balance()
sched: Remove useless code in yield_to()
sched: Add time unit suffix to sched sysctl knobs
sched/debug: Limit sd->*_idx range on sysctl
sched: Remove AFFINE_WAKEUPS feature flag
s390: Remove leftover account_tick_vtime() header
cputime: Consolidate vtime handling on context switch
sched: Move cputime code to its own file
cputime: Generalize CONFIG_VIRT_CPU_ACCOUNTING
tile: Remove SD_PREFER_LOCAL leftover
...
We only do rounding to the next nanosecond so we don't see minor
1ns inconsistencies in the vsyscall implementations. Since we're
changing the vsyscall implementations to avoid this, conditionalize
the rounding only to the GENERIC_TIME_VSYSCALL_OLD architectures.
Cc: Tony Luck <tony.luck@intel.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Paul Turner <pjt@google.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Richard Cochran <richardcochran@gmail.com>
Cc: Prarit Bhargava <prarit@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Now that we moved everyone over to GENERIC_TIME_VSYSCALL_OLD,
introduce the new declaration and config option for the new
update_vsyscall method.
Cc: Tony Luck <tony.luck@intel.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Paul Turner <pjt@google.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Richard Cochran <richardcochran@gmail.com>
Cc: Prarit Bhargava <prarit@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: John Stultz <john.stultz@linaro.org>
To help migrate archtectures over to the new update_vsyscall method,
redfine CONFIG_GENERIC_TIME_VSYSCALL as CONFIG_GENERIC_TIME_VSYSCALL_OLD
Cc: Tony Luck <tony.luck@intel.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Paul Turner <pjt@google.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Richard Cochran <richardcochran@gmail.com>
Cc: Prarit Bhargava <prarit@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: John Stultz <john.stultz@linaro.org>
We're going to need to access the timekeeper in update_vsyscall,
so make the structure available for those who need it.
Cc: Tony Luck <tony.luck@intel.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Paul Turner <pjt@google.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Richard Cochran <richardcochran@gmail.com>
Cc: Prarit Bhargava <prarit@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: John Stultz <john.stultz@linaro.org>
CLOCK_TICK_RATE is used to accurately caclulate exactly how
a tick will be at a given HZ.
This is useful, because while we'd expect NSEC_PER_SEC/HZ,
the underlying hardware will have some granularity limit,
so we won't be able to have exactly HZ ticks per second.
This slight error can cause timekeeping quality problems
when using the jiffies or other jiffies driven clocksources.
Thus we currently use compile time CLOCK_TICK_RATE value to
generate SHIFTED_HZ and NSEC_PER_JIFFIES, which we then use
to adjust the jiffies clocksource to correct this error.
Unfortunately though, since CLOCK_TICK_RATE is a compile
time value, and the jiffies clocksource is registered very
early during boot, there are a number of cases where there
are different possible hardware timers that have different
tick rates. This causes problems in cases like ARM where
there are numerous different types of hardware, each having
their own compile-time CLOCK_TICK_RATE, making it hard to
accurately support different hardware with a single kernel.
For the most part, this doesn't matter all that much, as not
too many systems actually utilize the jiffies or jiffies driven
clocksource. Usually there are other highres clocksources
who's granularity error is negligable.
Even so, we have some complicated calcualtions that we do
everywhere to handle these edge cases.
This patch removes the compile time SHIFTED_HZ value, and
introduces a register_refined_jiffies() function. This results
in the default jiffies clock as being assumed a perfect HZ
freq, and allows archtectures that care about jiffies accuracy
to call register_refined_jiffies() with the tick rate, specified
dynamically at boot.
This allows us, where necessary, to not have a compile time
CLOCK_TICK_RATE constant, simplifies the jiffies code, and
still provides a way to have an accurate jiffies clock.
NOTE: Since this patch does not add register_refinied_jiffies()
calls for every arch, it may cause time quality regressions
in some cases. Its likely these will not be noticable, but
if they are an issue, adding the following to the end of
setup_arch() should resolve the regression:
register_refinied_jiffies(CLOCK_TICK_RATE)
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Richard Cochran <richardcochran@gmail.com>
Cc: Prarit Bhargava <prarit@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Now that alarmtimer_remove has been simplified, change
its name to _dequeue to better match its paired _enqueue
function.
Cc: Arve Hjønnevåg <arve@android.com>
Cc: Colin Cross <ccross@android.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Arve Hjønnevåg reported numerous crashes from the
"BUG_ON(timer->state != HRTIMER_STATE_CALLBACK)" check
in __run_hrtimer after it called alarmtimer_fired.
It ends up the alarmtimer code was not properly handling
possible failures of hrtimer_try_to_cancel, and because
these faulres occur when the underlying base hrtimer is
being run, this limits the ability to properly handle
modifications to any alarmtimers on that base.
Because much of the logic duplicates the hrtimer logic,
it seems that we might as well have a per-alarmtimer
hrtimer, and avoid the extra complextity of trying to
multiplex many alarmtimers off of one hrtimer.
Thus this patch moves the hrtimer to the alarm structure
and simplifies the management logic.
Changelog:
v2:
* Includes a fix for double alarm_start calls found by
Arve
Cc: Arve Hjønnevåg <arve@android.com>
Cc: Colin Cross <ccross@android.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Reported-by: Arve Hjønnevåg <arve@android.com>
Tested-by: Arve Hjønnevåg <arve@android.com>
Signed-off-by: John Stultz <john.stultz@linaro.org>
alarmtimer suspend return -EBUSY if the next alarm will fire in less
than 2 seconds. This allows one RTC seconds tick to occur subsequent
to this check before the alarm wakeup time is set, ensuring the wakeup
time is still in the future (assuming the RTC does not tick one more
second prior to setting the alarm).
If suspend is rejected due to an imminent alarm, hold a wakeup source
for 2 seconds to process the alarm prior to reattempting suspend.
If setting the alarm incurs an -ETIME for an alarm set in the past,
or any other problem setting the alarm, abort suspend and hold a
wakelock for 1 second while the alarm is allowed to be serviced or
other hopefully transient conditions preventing the alarm clear up.
Signed-off-by: Todd Poynor <toddpoynor@google.com>
Signed-off-by: John Stultz <john.stultz@linaro.org>
The can_stop_idle_tick() function complains if a softirq vector is
raised too late in the idle-entry process, presumably in order to
prevent dangling softirq invocations from being delayed across the
full idle period, which might be indefinitely long -- and if softirq
was asserted any later than the call to this function, such a delay
might well happen.
However, RCU needs to be able to use softirq to stop idle entry in
order to be able to drain RCU callbacks from the current CPU, which in
turn enables faster entry into dyntick-idle mode, which in turn reduces
power consumption. Because RCU takes this action at a well-defined
point in the idle-entry path, it is safe for RCU to take this approach.
This commit therefore silences the error message that is sometimes
produced when the going-idle CPU suddenly finds that it has an RCU_SOFTIRQ
to process. The error message will continue to be issued for other
softirq vectors.
Reported-by: Sedat Dilek <sedat.dilek@gmail.com>
Signed-off-by: Paul E. McKenney <paul.mckenney@linaro.org>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Tested-by: Sedat Dilek <sedat.dilek@gmail.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Pull timer fix from Ingo Molnar:
"One more timekeeping fix for v3.6"
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
time: Fix timeekeping_get_ns overflow on 32bit systems
* pm-timers:
PM: Do not use the syscore flag for runtime PM
sh: MTU2: Basic runtime PM support
sh: CMT: Basic runtime PM support
sh: TMU: Basic runtime PM support
PM / Domains: Do not measure start time for "irq safe" devices
PM / Domains: Move syscore flag from subsys data to struct device
PM / Domains: Rename the always_on device flag to syscore
PM / Runtime: Allow helpers to be called by early platform drivers
PM: Reorganize device PM initialization
sh: MTU2: Introduce clock events suspend/resume routines
sh: CMT: Introduce clocksource/clock events suspend/resume routines
sh: TMU: Introduce clocksource/clock events suspend/resume routines
timekeeping: Add suspend and resume of clock event devices
PM / Domains: Add power off/on function for system core suspend stage
PM / Domains: Introduce simplified power on routine for system resume
Daniel Lezcano reported seeing multi-second stalls from
keyboard input on his T61 laptop when NOHZ and CPU_IDLE
were enabled on a 32bit kernel.
He bisected the problem down to commit
1e75fa8be9 ("time: Condense timekeeper.xtime into xtime_sec").
After reproducing this issue, I narrowed the problem down
to the fact that timekeeping_get_ns() returns a 64bit
nsec value that hasn't been accumulated. In some cases
this value was being then stored in timespec.tv_nsec
(which is a long).
On 32bit systems, with idle times larger then 4 seconds
(or less, depending on the value of xtime_nsec), the
returned nsec value would overflow 32bits. This limited
kept time from increasing, causing timers to not expire.
The fix is to make sure we don't directly store the
result of timekeeping_get_ns() into a tv_nsec field,
instead using a 64bit nsec value which can then be
added into the timespec via timespec_add_ns().
Reported-and-bisected-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Tested-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Acked-by: Prarit Bhargava <prarit@redhat.com>
Cc: Richard Cochran <richardcochran@gmail.com>
Link: http://lkml.kernel.org/r/1347405963-35715-1-git-send-email-john.stultz@linaro.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
There is no load_balancer to be selected now. It just sets the
state of the nohz tick to stop.
So rename the function, pass the 'cpu' as a parameter and then
remove the useless call from tick_nohz_restart_sched_tick().
[ s/set_nohz_tick_stopped/nohz_balance_enter_idle/g
s/clear_nohz_tick_stopped/nohz_balance_exit_idle/g ]
Signed-off-by: Alex Shi <alex.shi@intel.com>
Acked-by: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: Venkatesh Pallipadi <venki@google.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/1347261059-24747-1-git-send-email-alex.shi@intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Azat Khuzhin reported high loadavg in Linux v3.6
After checking the upstream scheduler code, I found Peter's commit:
5167e8d541 sched/nohz: Rewrite and fix load-avg computation -- again
not fully applied, missing the call to calc_load_exit_idle().
After that idle exit in sampling window will always be calculated
to non-idle, and the load will be higher than normal.
This patch adds the missing call to calc_load_exit_idle().
Signed-off-by: Charles Wang <muming.wq@taobao.com>
Cc: stable@kernel.org
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/1345449754-27130-1-git-send-email-muming.wq@gmail.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Some clock event devices, for example such that belong to PM domains,
need to be handled in a spcial way during the timekeeping suspend
and resume (which takes place in the system core, or "syscore",
stages of system power transitions) in analogy with clock sources.
Introduce .suspend() and .resume() callbacks for clock event devices
that will be executed by timekeeping_suspend/_resume(), respectively,
next the the clock sources' .suspend() and .resume() callbacks.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Andreas Bombe reported that the added ktime_t overflow checking added to
timespec_valid in commit 4e8b14526c ("time: Improve sanity checking of
timekeeping inputs") was causing problems with X.org because it caused
timeouts larger then KTIME_T to be invalid.
Previously, these large timeouts would be clamped to KTIME_MAX and would
never expire, which is valid.
This patch splits the ktime_t overflow checking into a new
timespec_valid_strict function, and converts the timekeeping codes
internal checking to use this more strict function.
Reported-and-tested-by: Andreas Bombe <aeb@debian.org>
Cc: Zhouping Liu <zliu@redhat.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Prarit Bhargava <prarit@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If update_wall_time() is called and the current offset isn't large
enough to accumulate, avoid re-calling timekeeping_adjust which may
change the clock freq and can cause 1ns inconsistencies with
CLOCK_REALTIME_COARSE/CLOCK_MONOTONIC_COARSE.
Signed-off-by: John Stultz <john.stultz@linaro.org>
Cc: Prarit Bhargava <prarit@redhat.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: stable@vger.kernel.org
Link: http://lkml.kernel.org/r/1345595449-34965-5-git-send-email-john.stultz@linaro.org
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Andreas Schwab noticed that the 1 << tk->shift could overflow if the
shift value was greater than 30, since 1 would be a 32bit long on
32bit architectures. This issue was introduced by 1e75fa8be (time:
Condense timekeeper.xtime into xtime_sec)
Use 1ULL instead to ensure we don't overflow on the shift.
Reported-by: Andreas Schwab <schwab@linux-m68k.org>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Cc: Prarit Bhargava <prarit@redhat.com>
Cc: Ingo Molnar <mingo@kernel.org>
Link: http://lkml.kernel.org/r/1345595449-34965-4-git-send-email-john.stultz@linaro.org
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
arch_gettimeoffset returns a u32 value which when shifted by tk->shift
can overflow. This issue was introduced with 1e75fa8be (time: Condense
timekeeper.xtime into xtime_sec)
Cast it to u64 first.
Signed-off-by: Andreas Schwab <schwab@linux-m68k.org>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Cc: Prarit Bhargava <prarit@redhat.com>
Cc: Ingo Molnar <mingo@kernel.org>
Link: http://lkml.kernel.org/r/1345595449-34965-3-git-send-email-john.stultz@linaro.org
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Andreas noticed problems with resume on specific hardware after commit
1e75fa8b (time: Condense timekeeper.xtime into xtime_sec) combined
with commit b44d50dca (time: Fix casting issue in tk_set_xtime and
tk_xtime_add)
After some digging I realized we aren't normalizing the timekeeper
after the add. Add the missing normalize call.
Reported-by: Andreas Schwab <schwab@linux-m68k.org>
Tested-by: Andreas Schwab <schwab@linux-m68k.org>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Cc: Prarit Bhargava <prarit@redhat.com>
Cc: Ingo Molnar <mingo@kernel.org>
Link: http://lkml.kernel.org/r/1345595449-34965-2-git-send-email-john.stultz@linaro.org
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Unexpected behavior could occur if the time is set to a value large
enough to overflow a 64bit ktime_t (which is something larger then the
year 2262).
Also unexpected behavior could occur if large negative offsets are
injected via adjtimex.
So this patch improves the sanity check timekeeping inputs by
improving the timespec_valid() check, and then makes better use of
timespec_valid() to make sure we don't set the time to an invalid
negative value or one that overflows ktime_t.
Note: This does not protect from setting the time close to overflowing
ktime_t and then letting natural accumulation cause the overflow.
Reported-by: CAI Qian <caiqian@redhat.com>
Reported-by: Sasha Levin <levinsasha928@gmail.com>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Prarit Bhargava <prarit@redhat.com>
Cc: Zhouping Liu <zliu@redhat.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: stable@vger.kernel.org
Link: http://lkml.kernel.org/r/1344454580-17031-1-git-send-email-john.stultz@linaro.org
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tetsuo Handa reported that sporadically the system clock starts
counting up too quickly which is enough to confuse the hangcheck
timer to print a bogus stall warning.
Commit 2a8c0883 "time: Move xtime_nsec adjustment underflow handling
timekeeping_adjust" overlooked this exit path:
} else
return;
which should really be a proper exit sequence, fixing the bug as a
side effect.
Also make the flow more readable by properly balancing curly
braces.
Reported-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp> wrote:
Tested-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp> wrote:
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Cc: john.stultz@linaro.org
Cc: a.p.zijlstra@chello.nl
Cc: richardcochran@gmail.com
Cc: prarit@redhat.com
Link: http://lkml.kernel.org/r/20120804192114.GA28347@gmail.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Ingo noted that the numerous timekeeper.value references made
the timekeeping code ugly and caused many long lines that
had to be broken up. He recommended replacing timekeeper.value
references with tk->value.
This patch provides a local tk value for all top level time
functions and sets it to &timekeeper. Then all timekeeper
access is done via a tk pointer.
Signed-off-by: John Stultz <john.stultz@linaro.org>
Cc: Prarit Bhargava <prarit@redhat.com>
Link: http://lkml.kernel.org/r/1343414893-45779-6-git-send-email-john.stultz@linaro.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
For performance reasons, we maintain ktime_t based duplicates of
wall_to_monotonic (offs_real) and total_sleep_time (offs_boot).
Since large problems could occur (such as the resume regression
on 3.5-rc7, or the leapsecond hrtimer issue) if these value
pairs were to be inconsistently updated, this patch this cleans
up how we modify these value pairs to ensure we are always
consistent.
As a side-effect this is also more efficient as we only
caulculate the duplicate values when they are changed,
rather then every update_wall_time call.
This also provides WARN_ONs to detect if future changes break
the invariants.
Signed-off-by: John Stultz <john.stultz@linaro.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Richard Cochran <richardcochran@gmail.com>
Cc: Prarit Bhargava <prarit@redhat.com>
Link: http://lkml.kernel.org/r/1343414893-45779-5-git-send-email-john.stultz@linaro.org
[ Cleaned up minor style issues. ]
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Ingo noted that ACTHZ is a confusing name, and requested it
be renamed, so this patch renames ACTHZ to SHIFTED_HZ to
better describe it.
Signed-off-by: John Stultz <john.stultz@linaro.org>
Cc: Prarit Bhargava <prarit@redhat.com>
Link: http://lkml.kernel.org/r/1343414893-45779-3-git-send-email-john.stultz@linaro.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
commit 1e75fa8b (time: Condense timekeeper.xtime into xtime_sec)
introduced helper functions which apply a timespec to the core
internal timekeeper data. The internal storage type is u64. The
timespec tv_nsec value must be shifted before set or added to the
internal value. tv_nsec is a long, which is 32bit on a 32bit system,
so without casting tv_nsec to u64 we lose the bits which are shifted
over the 32bit boundary.
Add the proper typecasts.
Reported-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Tested-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Acked-by: Prarit Bhargava <prarit@redhat.com>
Link: http://lkml.kernel.org/r/1343074957-16541-1-git-send-email-john.stultz@linaro.org
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Pull timer core changes from Ingo Molnar:
"Continued cleanups of the core time and NTP code, plus more nohz work
preparing for tick-less userspace execution."
* 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
time: Rework timekeeping functions to take timekeeper ptr as argument
time: Move xtime_nsec adjustment underflow handling timekeeping_adjust
time: Move arch_gettimeoffset() usage into timekeeping_get_ns()
time: Refactor accumulation of nsecs to secs
time: Condense timekeeper.xtime into xtime_sec
time: Explicitly use u32 instead of int for shift values
time: Whitespace cleanups per Ingo%27s requests
nohz: Move next idle expiry time record into idle logic area
nohz: Move ts->idle_calls incrementation into strict idle logic
nohz: Rename ts->idle_tick to ts->last_tick
nohz: Make nohz API agnostic against idle ticks cputime accounting
nohz: Separate idle sleeping time accounting from nohz logic
timers: Improve get_next_timer_interrupt()
timers: Add accounting of non deferrable timers
timers: Consolidate base->next_timer update
timers: Create detach_if_pending() and use it
Pull RCU changes from Ingo Molnar:
"Quoting from Paul, the major features of this series are:
1. Preventing latency spikes of more than 200 microseconds for
kernels built with NR_CPUS=4096, which is reportedly becoming the
default for some distros. This is a first step, as it does not
help with systems that actually -have- 4096 CPUs (work on this case
is in progress, but is not yet ready for mainline).
This category also includes improving concurrency of rcu_barrier(),
placed here due to conflicts. Posted to LKML at:
https://lkml.org/lkml/2012/6/22/381
Note that patches 18-22 of that series have been defered to 3.7, as
they have not yet proven themselves to be mainline-ready (and yes,
these are the ones intended to get rid of RCU's latency spikes for
systems that actually have 4096 CPUs).
2. Updates to documentation and rcutorture fixes, the latter category
including improvements to rcu_barrier() testing. Posted to LKML at
http://lkml.indiana.edu/hypermail/linux/kernel/1206.1/04094.html.
3. Miscellaneous fixes posted to LKML at:
https://lkml.org/lkml/2012/6/22/500
with the exception of the last commit, which was posted here:
http://www.gossamer-threads.com/lists/linux/kernel/1561830
4. RCU_FAST_NO_HZ fixes and improvements. Posted to LKML at:
http://lkml.indiana.edu/hypermail/linux/kernel/1206.1/00006.htmlhttp://www.gossamer-threads.com/lists/linux/kernel/1561833
The first four patches of the first series went into 3.5 to fix a
regression.
5. Code-style fixes. These were posted to LKML at
http://lkml.indiana.edu/hypermail/linux/kernel/1205.2/01180.htmlhttp://lkml.indiana.edu/hypermail/linux/kernel/1205.2/01181.html"
* 'core-rcu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (48 commits)
rcu: Fix broken strings in RCU's source code.
rcu: Fix code-style issues involving "else"
rcu: Introduce check for callback list/count mismatch
rcu: Make RCU_FAST_NO_HZ respect nohz= boot parameter
rcu: Fix qlen_lazy breakage
rcu: Round FAST_NO_HZ lazy timeout to nearest second
rcu: The rcu_needs_cpu() function is not a quiescent state
rcu: Dump only the current CPU's buffers for idle-entry/exit warnings
rcu: Add check for CPUs going offline with callbacks queued
rcu: Disable preemption in rcu_blocking_is_gp()
rcu: Prevent uninitialized string in RCU CPU stall info
rcu: Fix rcu_is_cpu_idle() #ifdef in TINY_RCU
rcu: Split RCU core processing out of __call_rcu()
rcu: Prevent __call_rcu() from invoking RCU core on offline CPUs
rcu: Make __call_rcu() handle invocation from idle
rcu: Remove function versions of __kfree_rcu and __is_kfree_rcu_offset
rcu: Consolidate tree/tiny __rcu_read_{,un}lock() implementations
rcu: Remove return value from rcu_assign_pointer()
key: Remove extraneous parentheses from rcu_assign_keypointer()
rcu: Remove return value from RCU_INIT_POINTER()
...
One more time/ntp fix pulled from Ingo Molnar.
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
ntp: Fix STA_INS/DEL clearing bug
The leap second rework unearthed another issue of inconsistent data.
On timekeeping_resume() the timekeeper data is updated, but nothing
calls timekeeping_update(), so now the update code in the timer
interrupt sees stale values.
This has been the case before those changes, but then the timer
interrupt was using stale data as well so this went unnoticed for quite
some time.
Add the missing update call, so all the data is consistent everywhere.
Reported-by: Andreas Schwab <schwab@linux-m68k.org>
Reported-and-tested-by: "Rafael J. Wysocki" <rjw@sisk.pl>
Reported-and-tested-by: Martin Steigerwald <Martin@lichtvoll.de>
Cc: LKML <linux-kernel@vger.kernel.org>
Cc: Linux PM list <linux-pm@vger.kernel.org>
Cc: John Stultz <johnstul@us.ibm.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>,
Cc: Prarit Bhargava <prarit@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: John Stultz <johnstul@us.ibm.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
As part of cleaning up the timekeeping code, this patch converts
a number of internal functions to takei a timekeeper ptr as an
argument, so that the internal functions don't access the global
timekeeper structure directly. This allows for further optimizations
to reduce lock hold time later.
This patch has been updated to include more consistent usage of the
timekeeper value, by making sure it is always passed as a argument
to non top-level functions.
Signed-off-by: John Stultz <john.stultz@linaro.org>
Reviewed-by: Ingo Molnar <mingo@kernel.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Richard Cochran <richardcochran@gmail.com>
Cc: Prarit Bhargava <prarit@redhat.com>
Link: http://lkml.kernel.org/r/1342156917-25092-9-git-send-email-john.stultz@linaro.org
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
When we make adjustments speeding up the clock, its possible
for xtime_nsec to underflow. We already handle this properly,
but we do so from update_wall_time() instead of the more logical
timekeeping_adjust(), where the possible underflow actually
occurs.
Thus, move the correction logic to the timekeeping_adjust, which
is the function that causes the issue. Making update_wall_time()
more readable.
Signed-off-by: John Stultz <johnstul@us.ibm.com>
Reviewed-by: Ingo Molnar <mingo@kernel.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Richard Cochran <richardcochran@gmail.com>
Cc: Prarit Bhargava <prarit@redhat.com>
Link: http://lkml.kernel.org/r/1342156917-25092-8-git-send-email-john.stultz@linaro.org
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Since we call arch_gettimeoffset() in all the accessor
functions, move arch_gettimeoffset() calls into
timekeeping_get_ns() and timekeeping_get_ns_raw() to simplify
the code.
This also makes the code easier to maintain as we don't have to
worry about forgetting the arch_gettimeoffset() as has happened
in the past.
Signed-off-by: John Stultz <johnstul@us.ibm.com>
Reviewed-by: Ingo Molnar <mingo@kernel.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Richard Cochran <richardcochran@gmail.com>
Cc: Prarit Bhargava <prarit@redhat.com>
Link: http://lkml.kernel.org/r/1342156917-25092-7-git-send-email-john.stultz@linaro.org
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
We do the exact same logic moving nsecs to secs in the
timekeeper in multiple places, so condense this into a
single function.
Signed-off-by: John Stultz <john.stultz@linaro.org>
Reviewed-by: Ingo Molnar <mingo@kernel.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Richard Cochran <richardcochran@gmail.com>
Cc: Prarit Bhargava <prarit@redhat.com>
Link: http://lkml.kernel.org/r/1342156917-25092-6-git-send-email-john.stultz@linaro.org
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The timekeeper struct has a xtime_nsec, which keeps the
sub-nanosecond remainder. This ends up being somewhat
duplicative of the timekeeper.xtime.tv_nsec value, and we
have to do extra work to keep them apart, copying the full
nsec portion out and back in over and over.
This patch simplifies some of the logic by taking the timekeeper
xtime value and splitting it into timekeeper.xtime_sec and
reuses the timekeeper.xtime_nsec for the sub-second portion
(stored in higher res shifted nanoseconds).
This simplifies some of the accumulation logic. And will
allow for more accurate timekeeping once the vsyscall code
is updated to use the shifted nanosecond remainder.
Signed-off-by: John Stultz <john.stultz@linaro.org>
Reviewed-by: Ingo Molnar <mingo@kernel.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Richard Cochran <richardcochran@gmail.com>
Cc: Prarit Bhargava <prarit@redhat.com>
Link: http://lkml.kernel.org/r/1342156917-25092-5-git-send-email-john.stultz@linaro.org
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Ingo noted that using a u32 instead of int for shift values
would be better to make sure the compiler doesn't unnecessarily
use complex signed arithmetic.
Signed-off-by: John Stultz <john.stultz@linaro.org>
Reviewed-by: Ingo Molnar <mingo@kernel.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Richard Cochran <richardcochran@gmail.com>
Cc: Prarit Bhargava <prarit@redhat.com>
Link: http://lkml.kernel.org/r/1342156917-25092-4-git-send-email-john.stultz@linaro.org
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Ingo noted a number of places where there is inconsistent
use of whitespace. This patch tries to address the main
culprits.
Signed-off-by: John Stultz <john.stultz@linaro.org>
Reviewed-by: Ingo Molnar <mingo@kernel.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Richard Cochran <richardcochran@gmail.com>
Cc: Prarit Bhargava <prarit@redhat.com>
Link: http://lkml.kernel.org/r/1342156917-25092-3-git-send-email-john.stultz@linaro.org
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reason: Update to upstream changes to avoid further conflicts.
Fixup a trivial merge conflict in kernel/time/tick-sched.c
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
In commit 6b43ae8a61, I
introduced a bug that kept the STA_INS or STA_DEL bit
from being cleared from time_status via adjtimex()
without forcing STA_PLL first.
Usually once the STA_INS is set, it isn't cleared
until the leap second is applied, so its unlikely this
affected anyone. However during testing I noticed it
took some effort to cancel a leap second once STA_INS
was set.
Signed-off-by: John Stultz <johnstul@us.ibm.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Richard Cochran <richardcochran@gmail.com>
Cc: Prarit Bhargava <prarit@redhat.com>
CC: stable@vger.kernel.org # 3.4
Link: http://lkml.kernel.org/r/1342156917-25092-2-git-send-email-john.stultz@linaro.org
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Pull RCU, perf, and scheduler fixes from Ingo Molnar.
The RCU fix is a revert for an optimization that could cause deadlocks.
One of the scheduler commits (164c33c6ad "sched: Fix fork() error path
to not crash") is correct but not complete (some architectures like Tile
are not covered yet) - the resulting additional fixes are still WIP and
Ingo did not want to delay these pending fixes. See this thread on
lkml:
[PATCH] fork: fix error handling in dup_task()
The perf fixes are just trivial oneliners.
* 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
Revert "rcu: Move PREEMPT_RCU preemption to switch_to() invocation"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf kvm: Fix segfault with report and mixed guestmount use
perf kvm: Fix regression with guest machine creation
perf script: Fix format regression due to libtraceevent merge
ring-buffer: Fix accounting of entries when removing pages
ring-buffer: Fix crash due to uninitialized new_pages list head
* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
MAINTAINERS/sched: Update scheduler file pattern
sched/nohz: Rewrite and fix load-avg computation -- again
sched: Fix fork() error path to not crash
To finally fix the infamous leap second issue and other race windows
caused by functions which change the offsets between the various time
bases (CLOCK_MONOTONIC, CLOCK_REALTIME and CLOCK_BOOTTIME) we need a
function which atomically gets the current monotonic time and updates
the offsets of CLOCK_REALTIME and CLOCK_BOOTTIME with minimalistic
overhead. The previous patch which provides ktime_t offsets allows us
to make this function almost as cheap as ktime_get() which is going to
be replaced in hrtimer_interrupt().
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Ingo Molnar <mingo@kernel.org>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Acked-by: Prarit Bhargava <prarit@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: John Stultz <johnstul@us.ibm.com>
Link: http://lkml.kernel.org/r/1341960205-56738-7-git-send-email-johnstul@us.ibm.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
We need to update the hrtimer clock offsets from the hrtimer interrupt
context. To avoid conversions from timespec to ktime_t maintain a
ktime_t based representation of those offsets in the timekeeper. This
puts the conversion overhead into the code which updates the
underlying offsets and provides fast accessible values in the hrtimer
interrupt.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: John Stultz <johnstul@us.ibm.com>
Reviewed-by: Ingo Molnar <mingo@kernel.org>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Acked-by: Prarit Bhargava <prarit@redhat.com>
Cc: stable@vger.kernel.org
Link: http://lkml.kernel.org/r/1341960205-56738-4-git-send-email-johnstul@us.ibm.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The timekeeping code misses an update of the hrtimer subsystem after a
leap second happened. Due to that timers based on CLOCK_REALTIME are
either expiring a second early or late depending on whether a leap
second has been inserted or deleted until an operation is initiated
which causes that update. Unless the update happens by some other
means this discrepancy between the timekeeping and the hrtimer data
stays forever and timers are expired either early or late.
The reported immediate workaround - $ data -s "`date`" - is causing a
call to clock_was_set() which updates the hrtimer data structures.
See: http://www.sheeri.com/content/mysql-and-leap-second-high-cpu-and-fix
Add the missing clock_was_set() call to update_wall_time() in case of
a leap second event. The actual update is deferred to softirq context
as the necessary smp function call cannot be invoked from hard
interrupt context.
Signed-off-by: John Stultz <johnstul@us.ibm.com>
Reported-by: Jan Engelhardt <jengelh@inai.de>
Reviewed-by: Ingo Molnar <mingo@kernel.org>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Acked-by: Prarit Bhargava <prarit@redhat.com>
Cc: stable@vger.kernel.org
Link: http://lkml.kernel.org/r/1341960205-56738-3-git-send-email-johnstul@us.ibm.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Thanks to Charles Wang for spotting the defects in the current code:
- If we go idle during the sample window -- after sampling, we get a
negative bias because we can negate our own sample.
- If we wake up during the sample window we get a positive bias
because we push the sample to a known active period.
So rewrite the entire nohz load-avg muck once again, now adding
copious documentation to the code.
Reported-and-tested-by: Doug Smythies <dsmythies@telus.net>
Reported-and-tested-by: Charles Wang <muming.wq@gmail.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: stable@kernel.org
Link: http://lkml.kernel.org/r/1340373782.18025.74.camel@twins
[ minor edits ]
Signed-off-by: Ingo Molnar <mingo@kernel.org>
If the nohz= boot parameter disables nohz, then RCU_FAST_NO_HZ needs to
also disable itself. This commit therefore checks for tick_nohz_enabled
being zero, disabling rcu_prepare_for_idle() if so. This commit assumes
that tick_nohz_enabled can change at runtime: If this is not the case,
then a simpler approach suffices.
Signed-off-by: Paul E. McKenney <paul.mckenney@linaro.org>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Pull core updates (RCU and locking) from Ingo Molnar:
"Most of the diffstat comes from the RCU slow boot regression fixes,
but there's also a debuggability improvements/fixes."
* 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
memblock: Document memblock_is_region_{memory,reserved}()
rcu: Precompute RCU_FAST_NO_HZ timer offsets
rcu: Move RCU_FAST_NO_HZ per-CPU variables to rcu_dynticks structure
rcu: Update RCU_FAST_NO_HZ tracing for lazy callbacks
rcu: RCU_FAST_NO_HZ detection of callback adoption
spinlock: Indicate that a lockup is only suspected
kdump: Execute kmsg_dump(KMSG_DUMP_PANIC) after smp_send_stop()
panic: Make panic_on_oops configurable
The next idle expiry time record and idle sleeps tracking are
statistics that only concern idle.
Since we want the nohz APIs to become usable further idle
context, let's pull up the handling of these statistics to the
callers in idle.
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Alessio Igor Bogani <abogani@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Avi Kivity <avi@redhat.com>
Cc: Chris Metcalf <cmetcalf@tilera.com>
Cc: Christoph Lameter <cl@linux.com>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Geoff Levand <geoff@infradead.org>
Cc: Gilad Ben Yossef <gilad@benyossef.com>
Cc: Hakan Akkan <hakanakkan@gmail.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Kevin Hilman <khilman@ti.com>
Cc: Max Krasnyansky <maxk@qualcomm.com>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephen Hemminger <shemminger@vyatta.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Sven-Thorsten Dietrich <thebigcorporation@gmail.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Since we want to prepare for making the nohz API to work further
the idle case, we need to pull ts->idle_calls incrementation up to
the callers in idle.
To perform this, we split tick_nohz_stop_sched_tick() in two parts:
a first one that checks if we can really stop the tick for idle,
and another that actually stops it. Then from the callers in idle,
we check if we can stop the tick and only then we increment idle_calls
and finally relay to the nohz API that won't care about these details
anymore.
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Alessio Igor Bogani <abogani@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Avi Kivity <avi@redhat.com>
Cc: Chris Metcalf <cmetcalf@tilera.com>
Cc: Christoph Lameter <cl@linux.com>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Geoff Levand <geoff@infradead.org>
Cc: Gilad Ben Yossef <gilad@benyossef.com>
Cc: Hakan Akkan <hakanakkan@gmail.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Kevin Hilman <khilman@ti.com>
Cc: Max Krasnyansky <maxk@qualcomm.com>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephen Hemminger <shemminger@vyatta.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Sven-Thorsten Dietrich <thebigcorporation@gmail.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Now that idle and nohz logics are going to be independant each others,
ts->idle_tick becomes too much a biased name to describe the field that
saves the last scheduled tick on top of which we re-calculate the next
tick to schedule when the timer is restarted.
We want to reuse this even to stop the tick outside idle cases. So let's
rename it to some more generic name: ts->last_tick.
This changes a bit the timer list stat export so we need to increase its
version.
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Alessio Igor Bogani <abogani@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Avi Kivity <avi@redhat.com>
Cc: Chris Metcalf <cmetcalf@tilera.com>
Cc: Christoph Lameter <cl@linux.com>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Geoff Levand <geoff@infradead.org>
Cc: Gilad Ben Yossef <gilad@benyossef.com>
Cc: Hakan Akkan <hakanakkan@gmail.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Kevin Hilman <khilman@ti.com>
Cc: Max Krasnyansky <maxk@qualcomm.com>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephen Hemminger <shemminger@vyatta.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Sven-Thorsten Dietrich <thebigcorporation@gmail.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
When the timer tick fires, it accounts the new jiffy as either part
of system, user or idle time. This is how we record the cputime
statistics.
But when the tick is stopped from the idle task, we still need
to record the number of jiffies spent tickless until we restart
the tick and fall back to traditional tick-based cputime accounting.
To do this, we take a snapshot of jiffies when the tick is stopped
and compute the difference against the new value of jiffies when
the tick is restarted. Then we account this whole difference to
the idle cputime.
However we are preparing to be able to stop the tick from other places
than idle. So this idle time accounting needs to be performed from
the callers of nohz APIs, not from the nohz APIs themselves because
we now want them to be agnostic against places that stop/restart tick.
Therefore, we pull the tickless idle time accounting out of generic
nohz helpers up to idle entry/exit callers.
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Alessio Igor Bogani <abogani@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Avi Kivity <avi@redhat.com>
Cc: Chris Metcalf <cmetcalf@tilera.com>
Cc: Christoph Lameter <cl@linux.com>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Geoff Levand <geoff@infradead.org>
Cc: Gilad Ben Yossef <gilad@benyossef.com>
Cc: Hakan Akkan <hakanakkan@gmail.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Kevin Hilman <khilman@ti.com>
Cc: Max Krasnyansky <maxk@qualcomm.com>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephen Hemminger <shemminger@vyatta.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Sven-Thorsten Dietrich <thebigcorporation@gmail.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
As we plan to be able to stop the tick outside the idle task, we
need to prepare for separating nohz logic from idle. As a start,
this pulls the idle sleeping time accounting out of the tick
stop/restart API to the callers on idle entry/exit.
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Alessio Igor Bogani <abogani@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Avi Kivity <avi@redhat.com>
Cc: Chris Metcalf <cmetcalf@tilera.com>
Cc: Christoph Lameter <cl@linux.com>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Geoff Levand <geoff@infradead.org>
Cc: Gilad Ben Yossef <gilad@benyossef.com>
Cc: Hakan Akkan <hakanakkan@gmail.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Kevin Hilman <khilman@ti.com>
Cc: Max Krasnyansky <maxk@qualcomm.com>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephen Hemminger <shemminger@vyatta.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Sven-Thorsten Dietrich <thebigcorporation@gmail.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Merge RCU fixes from Paul E. McKenney:
" This series has four patches, the major point of which is to eliminate
some slowdowns (including boot-time slowdowns) resulting from some
RCU_FAST_NO_HZ changes. The issue with the changes is that posting timers
from the idle loop has no effect if the CPU has entered dyntick-idle
mode because the CPU has already computed its wakeup time, and posting
a timer does not cause it to be recomputed. The short-term fix is for
RCU to precompute the timeout value so that the CPU's calculation is
correct. "
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Pull leap second timer fix from Thomas Gleixner.
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
timekeeping: Fix CLOCK_MONOTONIC inconsistency during leapsecond
When a CPU is entering dyntick-idle mode, tick_nohz_stop_sched_tick()
calls rcu_needs_cpu() see if RCU needs that CPU, and, if not, computes the
next wakeup time based on the timer wheels. Only later, when actually
entering the idle loop, rcu_prepare_for_idle() will be invoked. In some
cases, rcu_prepare_for_idle() will post timers to wake the CPU back up.
But all for naught: The next wakeup time for the CPU has already been
computed, and posting a timer afterwards does not force that wakeup
time to be recomputed. This means that rcu_prepare_for_idle()'s have
no effect.
This is not a problem on a busy system because something else will wake
up the CPU soon enough. However, on lightly loaded systems, the CPU
might stay asleep for a considerable length of time. If that CPU has
a callback that the rest of the system is waiting on, the system might
run very slowly or (in theory) even hang.
This commit avoids this problem by having rcu_needs_cpu() give
tick_nohz_stop_sched_tick() an estimate of when RCU will need the CPU
to wake back up, which tick_nohz_stop_sched_tick() takes into account
when programming the CPU's wakeup time. An alternative approach is
for rcu_prepare_for_idle() to use hrtimers instead of normal timers,
but timers are much more efficient than are hrtimers for frequently
and repeatedly posting and cancelling a given timer, which is exactly
what RCU_FAST_NO_HZ does.
Reported-by: Pascal Chapperon <pascal.chapperon@wanadoo.fr>
Reported-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Paul E. McKenney <paul.mckenney@linaro.org>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Tested-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Tested-by: Pascal Chapperon <pascal.chapperon@wanadoo.fr>
Pull scheduler fixes from Ingo Molnar.
* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched: Remove NULL assignment of dattr_cur
sched: Remove the last NULL entry from sched_feat_names
sched: Make sched_feat_names const
sched/rt: Fix SCHED_RR across cgroups
sched: Move nr_cpus_allowed out of 'struct sched_rt_entity'
sched: Make sure to not re-read variables after validation
sched: Fix SD_OVERLAP
sched: Don't try allocating memory from offline nodes
sched/nohz: Fix rq->cpu_load calculations some more
sched/x86: Use cpu_llc_shared_mask(cpu) for coregroup_mask
Commit 6b43ae8a61 (ntp: Fix leap-second hrtimer livelock) broke the
leapsecond update of CLOCK_MONOTONIC. The missing leapsecond update to
wall_to_monotonic causes discontinuities in CLOCK_MONOTONIC.
Adjust wall_to_monotonic when NTP inserted a leapsecond.
Reported-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Tested-by: Richard Cochran <richardcochran@gmail.com>
Cc: stable@kernel.org
Link: http://lkml.kernel.org/r/1338400497-12420-1-git-send-email-john.stultz@linaro.org
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Follow up on commit 556061b00 ("sched/nohz: Fix rq->cpu_load[]
calculations") since while that fixed the busy case it regressed the
mostly idle case.
Add a callback from the nohz exit to also age the rq->cpu_load[]
array. This closes the hole where either there was no nohz load
balance pass during the nohz, or there was a 'significant' amount of
idle time between the last nohz balance and the nohz exit.
So we'll update unconditionally from the tick to not insert any
accidental 0 load periods while busy, and we try and catch up from
nohz idle balance and nohz exit. Both these are still prone to missing
a jiffy, but that has always been the case.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: pjt@google.com
Cc: Venkatesh Pallipadi <venki@google.com>
Link: http://lkml.kernel.org/n/tip-kt0trz0apodbf84ucjfdbr1a@git.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Let the user decide whether power consumption or jitter is the
more important consideration for their machines.
Quoting removal commit af5ab277ded04bd9bc6b048c5a2f0e7d70ef0867:
"Historically, Linux has tried to make the regular timer tick on the
various CPUs not happen at the same time, to avoid contention on
xtime_lock.
Nowadays, with the tickless kernel, this contention no longer happens
since time keeping and updating are done differently. In addition,
this skew is actually hurting power consumption in a measurable way on
many-core systems."
Problems:
- Contrary to the above, systems do encounter contention on both
xtime_lock and RCU structure locks when the tick is synchronized.
- Moderate sized RT systems suffer intolerable jitter due to the tick
being synchronized.
- SGI reports the same for their large systems.
- Fully utilized systems reap no power saving benefit from skew removal,
but do suffer from resulting induced lock contention.
- 0209f649 rcu: limit rcu_node leaf-level fanout
This patch was born to combat lock contention which testing showed
to have been _induced by_ skew removal. Skew the tick, contention
disappeared virtually completely.
Signed-off-by: Mike Galbraith <mgalbraith@suse.de>
Link: http://lkml.kernel.org/r/1336472458.21924.78.camel@marge.simpson.net
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Pull timer updates from Thomas Gleixner.
Various trivial conflict fixups in arch Kconfig due to addition of
unrelated entries nearby. And one slightly more subtle one for sparc32
(new user of GENERIC_CLOCKEVENTS), fixed up as per Thomas.
* 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (31 commits)
timekeeping: Fix a few minor newline issues.
time: remove obsolete declaration
ntp: Fix a stale comment and a few stray newlines.
ntp: Correct TAI offset during leap second
timers: Fixup the Kconfig consolidation fallout
x86: Use generic time config
unicore32: Use generic time config
um: Use generic time config
tile: Use generic time config
sparc: Use: generic time config
sh: Use generic time config
score: Use generic time config
s390: Use generic time config
openrisc: Use generic time config
powerpc: Use generic time config
mn10300: Use generic time config
mips: Use generic time config
microblaze: Use generic time config
m68k: Use generic time config
m32r: Use generic time config
...
When repeating a UTC time value during a leap second (when the UTC
time should be 23:59:60), the TAI timescale should not stop. The kernel
NTP code increments the TAI offset one second too late. This patch fixes
the issue by incrementing the offset during the leap second itself.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Sigh, I missed to check which architecture Kconfig files actually
include the core Kconfig file. There are a few which did not. So we
broke them.
Instead of adding the includes to those, we are better off to move the
include to init/Kconfig like we did already with irqs and others.
This does not change anything for the architectures using the old
style periodic timer mode. It just solves the build wreckage there.
For those architectures which use the clock events infrastructure it
moves the include of the core Kconfig file to "General setup" which is
a way more logical place than having it at random locations specified
by the architecture specific Kconfigs.
Reported-by: Ingo Molnar <mingo@kernel.org>
Cc: Anna-Maria Gleixner <anna-maria@glx-um.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
We really don't want all the arch code defining stuff
over and over.
[ anna-maria: Added missing GENERIC_CMOS_UPDATE switch ]
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Anna-Maria Gleixner <anna-maria@glx-um.de>
Cc: Paul Mundt <lethal@linux-sh.org>
Link: http://lkml.kernel.org/r/1337529587.3208.2.camel@dionysos
Acked-by: Sam Ravnborg <sam@ravnborg.org>
The Android alarm interface provides a settime call that sets both
the alarmtimer RTC device and CLOCK_REALTIME to the same value.
Since there may be multiple rtc devices, provide a hook to access the
one the alarmtimer infrastructure is using.
CC: Colin Cross <ccross@android.com>
CC: Thomas Gleixner <tglx@linutronix.de>
CC: Android Kernel Team <kernel-team@android.com>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
During resume, tick_resume_broadcast() programs the broadcast timer in
oneshot mode unconditionally. On the platforms where broadcast timer
is not really required, this will generate spurious broadcast timer
ticks upon resume. For example, on the always running apic timer
platforms with HPET, I see spurious hpet tick once every ~5minutes
(which is the 32-bit hpet counter wraparound time).
Similar to boot time, during resume make the oneshot mode setting of
the broadcast clock event device conditional on the state of active
broadcast users.
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Tested-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: svenjoac@gmx.de
Cc: torvalds@linux-foundation.org
Cc: rjw@sisk.pl
Link: http://lkml.kernel.org/r/1334802459.28674.209.camel@sbsiddha-desk.sc.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Santosh found another trap when we avoid to initialize the broadcast
device in the switch_to_oneshot code. The broadcast device might be
still in SHUTDOWN state when we actually need to use it. That
obviously breaks, as set_next_event() is called on a shutdown
device. This did not break on x86, but Suresh analyzed it:
From the review, most likely on Sven's system we are force enabling
the hpet using the pci quirk's method very late. And in this case,
hpet_clockevent (which will be global_clock_event) handler can be
null, specifically as this platform might not be using deeper c-states
and using the reliable APIC timer.
Prior to commit 'fa4da365bc7772c', that handler will be set to
'tick_handle_oneshot_broadcast' when we switch the broadcast timer to
oneshot mode, even though we don't use it. Post commit
'fa4da365bc7772c', we stopped switching the broadcast mode to oneshot
as this is not really needed and his platform's global_clock_event's
handler will remain null. While on my SNB laptop, same is set to
'clockevents_handle_noop' because hpet gets enabled very early. (noop
handler on my platform set when the early enabled hpet timer gets
replaced by the lapic timer).
But the commit 'fa4da365bc7772c' tracked the broadcast timer mode in
the SW as oneshot, even though it didn't touch the HW timer. During
resume however, tick_resume_broadcast() saw the SW broadcast mode as
oneshot and actually programmed the broadcast device also into oneshot
mode. So this triggered the null pointer de-reference after the hpet
wraps around and depending on what the hpet counter is set to. On the
normal platforms where hpet gets enabled early we should be seeing a
spurious interrupt (in my SNB laptop I see one spurious interrupt
after around 5 minutes ;) which is 32-bit hpet counter wraparound
time), but that's a separate issue.
Enforce the mode setting when trying to set an event.
Reported-and-tested-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: torvalds@linux-foundation.org
Cc: svenjoac@gmx.de
Cc: rjw@sisk.pl
Link: http://lkml.kernel.org/r/alpine.LFD.2.02.1204181723350.2542@ionos
Sven Joachim reported, that suspend/resume on rc3 trips over a NULL
pointer dereference. Linus spotted the clockevent handler being NULL.
commit fa4da365b(clockevents: tTack broadcast device mode change in
tick_broadcast_switch_to_oneshot()) tried to fix a problem with the
broadcast device setup, which was introduced in commit 77b0d60c5(
clockevents: Leave the broadcast device in shutdown mode when not
needed).
The initial commit avoided to set up the broadcast device when no
broadcast request bits were set, but that left the broadcast device
disfunctional. In consequence deep idle states which need the
broadcast device were not woken up.
commit fa4da365b tried to fix that by initializing the state of the
broadcast facility, but that missed the fact, that nothing initializes
the event handler and some other state of the underlying clock event
device.
The fix is to revert both commits and make only the mode setting of
the clock event device conditional on the state of active broadcast
users.
That initializes everything except the low level device mode, but this
happens when the broadcast functionality is invoked by deep idle.
Reported-and-tested-by: Sven Joachim <svenjoac@gmx.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Suresh Siddha <suresh.b.siddha@intel.com>
Link: http://lkml.kernel.org/r/alpine.LFD.2.02.1204181205540.2542@ionos
In the commit 77b0d60c5a,
"clockevents: Leave the broadcast device in shutdown mode when not needed",
we were bailing out too quickly in tick_broadcast_switch_to_oneshot(),
with out tracking the broadcast device mode change to 'TICKDEV_MODE_ONESHOT'.
This breaks the platforms which need broadcast device oneshot services during
deep idle states. tick_broadcast_oneshot_control() thinks that it is
in periodic mode and fails to take proper decisions based on the
CLOCK_EVT_NOTIFY_BROADCAST_[ENTER, EXIT] notifications during deep
idle entry/exit.
Fix this by tracking the broadcast device mode as 'TICKDEV_MODE_ONESHOT',
before leaving the broadcast HW device in shutdown mode if there are no active
requests for the moment.
Reported-and-tested-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: johnstul@us.ibm.com
Link: http://lkml.kernel.org/r/1334011304.12400.81.camel@sbsiddha-desk.sc.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Fix tick_nohz_restart() to not use a stale ktime_t "now" value when
calling tick_do_update_jiffies64(now).
If we reach this point in the loop it means that we crossed a tick
boundary since we grabbed the "now" timestamp, so at this point "now"
refers to a time in the old jiffy, so using the old value for "now" is
incorrect, and is likely to give us a stale jiffies value.
In particular, the first time through the loop the
tick_do_update_jiffies64(now) call is always a no-op, since the
caller, tick_nohz_restart_sched_tick(), will have already called
tick_do_update_jiffies64(now) with that "now" value.
Note that tick_nohz_stop_sched_tick() already uses the correct
approach: when we notice we cross a jiffy boundary, grab a new
timestamp with ktime_get(), and *then* update jiffies.
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Cc: Ben Segall <bsegall@google.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: stable@vger.kernel.org
Link: http://lkml.kernel.org/r/1332875377-23014-1-git-send-email-ncardwell@google.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This option has been selected from arch code as it was assumed that
it's necessary to support oneshot mode clockevent devices. But it's
just a core internal helper to compile tick-oneshot.c if NOHZ or
HIG_RES_TIMERS are selected.
Reported-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Pull timer core updates from Thomas Gleixner.
* 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
ia64: vsyscall: Add missing paranthesis
alarmtimer: Don't call rtc_timer_init() when CONFIG_RTC_CLASS=n
x86: vdso: Put declaration before code
x86-64: Inline vdso clock_gettime helpers
x86-64: Simplify and optimize vdso clock_gettime monotonic variants
kernel-time: fix s/then/than/ spelling errors
time: remove no_sync_cmos_clock
time: Avoid scary backtraces when warning of > 11% adj
alarmtimer: Make sure we initialize the rtctimer
ntp: Fix leap-second hrtimer livelock
x86, tsc: Skip refined tsc calibration on systems with reliable TSC
rtc: Provide flag for rtc devices that don't support UIE
ia64: vsyscall: Use seqcount instead of seqlock
x86: vdso: Use seqcount instead of seqlock
x86: vdso: Remove bogus locking in update_vsyscall_tz()
time: Remove bogus comments
time: Fix change_clocksource locking
time: x86: Fix race switching from vsyscall to non-vsyscall clock
rtc_timer_init() is not available when CONFIG_RTC_CLASS=n. Provide a
proper wrapper in the RTC section of alarmtimer.c
Reported-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: John Stultz <john.stultz@linaro.org>
Use than for comparisons, like more than.
CC: John Stultz <john.stultz@linaro.org>
Signed-off-by: Jim Cromie <jim.cromie@gmail.com>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Commit 9863c90f68 (x86, vmware: Remove
deprecated VMI kernel support) removed the only place which set
no_sync_cmos_clock. Since that commit, this variable is never set.
Signed-off-by: Cesar Eduardo Barros <cesarb@cesarb.net>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Folks have been getting a number of warnings about time
adjustments > 11%. The WARN_ON leaves a big useless backtrace
so this patch removes it for a printk_once().
I'm still working to narrow down the cause of the > 11% adjustment.
Signed-off-by: John Stultz <john.stultz@linaro.org>
jonghwan Choi reported seeing warnings with the alarmtimer
code at suspend/resume time, and pointed out that the
rtctimer isn't being properly initialized.
This patch corrects this issue.
Reported-by: jonghwan Choi <jhbird.choi@gmail.com>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Pull input subsystem updates from Dmitry Torokhov:
"- we finally merged driver for USB version of Synaptics touchpads
(I guess most commonly found in IBM/Lenovo keyboard/touchpad combo);
- a bunch of new drivers for embedded platforms (Cypress
touchscreens, DA9052 OnKey, MAX8997-haptic, Ilitek ILI210x
touchscreens, TI touchscreen);
- input core allows clients to specify desired clock source for
timestamps on input events (EVIOCSCLOCKID ioctl);
- input core allows querying state of all MT slots for given event
code via EVIOCGMTSLOTS ioctl;
- various driver fixes and improvements."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (45 commits)
Input: ili210x - add support for Ilitek ILI210x based touchscreens
Input: altera_ps2 - use of_match_ptr()
Input: synaptics_usb - switch to module_usb_driver()
Input: convert I2C drivers to use module_i2c_driver()
Input: convert SPI drivers to use module_spi_driver()
Input: omap4-keypad - move platform_data to <linux/platform_data>
Input: kxtj9 - who_am_i check value and initial data rate fixes
Input: add driver support for MAX8997-haptic
Input: tegra-kbc - revise device tree support
Input: of_keymap - add device tree bindings for simple key matrices
Input: wacom - fix physical size calculation for 3rd-gen Bamboo
Input: twl4030-vibra - really switch from #if to #ifdef
Input: hp680_ts_input - ensure arguments to request_irq and free_irq are compatible
Input: max8925_onkey - avoid accessing input device too early
Input: max8925_onkey - allow to be used as a wakeup source
Input: atmel-wm97xx - convert to dev_pm_ops
Input: atmel-wm97xx - set driver owner
Input: add cyttsp touchscreen maintainer entry
Input: cyttsp - remove useless checks in cyttsp_probe()
Input: usbtouchscreen - add support for Data Modul EasyTouch TP 72037
...
Since commit 7dffa3c673 the ntp
subsystem has used an hrtimer for triggering the leapsecond
adjustment. However, this can cause a potential livelock.
Thomas diagnosed this as the following pattern:
CPU 0 CPU 1
do_adjtimex()
spin_lock_irq(&ntp_lock);
process_adjtimex_modes(); timer_interrupt()
process_adj_status(); do_timer()
ntp_start_leap_timer(); write_lock(&xtime_lock);
hrtimer_start(); update_wall_time();
hrtimer_reprogram(); ntp_tick_length()
tick_program_event() spin_lock(&ntp_lock);
clockevents_program_event()
ktime_get()
seq = req_seqbegin(xtime_lock);
This patch tries to avoid the problem by reverting back to not using
an hrtimer to inject leapseconds, and instead we handle the leapsecond
processing in the second_overflow() function.
The downside to this change is that on systems that support highres
timers, the leap second processing will occur on a HZ tick boundary,
(ie: ~1-10ms, depending on HZ) after the leap second instead of
possibly sooner (~34us in my tests w/ x86_64 lapic).
This patch applies on top of tip/timers/core.
CC: Sasha Levin <levinsasha928@gmail.com>
CC: Thomas Gleixner <tglx@linutronix.de>
Reported-by: Sasha Levin <levinsasha928@gmail.com>
Diagnoised-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Sasha Levin <levinsasha928@gmail.com>
Signed-off-by: John Stultz <john.stultz@linaro.org>
change_clocksource() fails to grab locks or call timekeeping_update(),
which leaves a race window for time inconsistencies.
This adds proper locking and a call to timekeeping_update() to fix this.
CC: Andy Lutomirski <luto@amacapital.net>
CC: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: John Stultz <john.stultz@linaro.org>
'long secs' is passed as divisor to div_s64, which accepts a 32bit
divisor. On 64bit machines that value is trimmed back from 8 bytes
back to 4, causing a divide by zero when the number is bigger than
(1 << 32) - 1 and all 32 lower bits are 0.
Use div64_long() instead.
Signed-off-by: Sasha Levin <levinsasha928@gmail.com>
Cc: johnstul@us.ibm.com
Link: http://lkml.kernel.org/r/1331829374-31543-2-git-send-email-levinsasha928@gmail.com
Cc: stable@vger.kernel.org
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
ts->inidle is set by tick_nohz_idle_enter() and unset by
tick_nohz_idle_exit(). However these two calls are assumed
to be always paired. This means that by the time we call
tick_nohz_idle_exit(), ts->inidle is supposed to be always
set to 1.
Remove the checks for ts->inidle in tick_nohz_idle_exit().
This simplifies a bit the code and improves its debuggability
(ie: ensure the call is paired with a tick_nohz_idle_enter()
call).
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Reviewed-by: Yong Zhang <yong.zhang0@gmail.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Ingo Molnar <mingo@elte.hu>
Link: http://lkml.kernel.org/r/1327427984-23282-2-git-send-email-fweisbec@gmail.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
There is no reason to call update_ts_time_stat from tick_nohz_start_idle
anymore (after e0e37c20 sched: Eliminate the ts->idle_lastupdate field)
when we updated idle_lastupdate unconditionally.
We haven't set idle_active yet and do not provide last_update_time so
the whole call end up being just 2 wasted branches.
Signed-off-by: Michal Hocko <mhocko@suse.cz>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Link: http://lkml.kernel.org/r/1322755222-6951-1-git-send-email-mhocko@suse.cz
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Platforms with Always Running APIC Timer doesn't use the broadcast timer
but the kernel is leaving the broadcast timer (HPET in this case)
in oneshot mode.
On these platforms, before the switch to oneshot mode, broadcast device is
actually in shutdown mode. Code checks for empty tick_broadcast_mask and
avoids going into the periodic mode.
During switch to oneshot mode, add the same tick_broadcast_mask checks in the
tick_broadcast_switch_to_oneshot() and avoid the broadcast device going into
the oneshot mode.
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: john stultz <johnstul@us.ibm.com>
Cc: venki@google.com
Link: http://lkml.kernel.org/r/1320452301.15071.16.camel@sbsiddha-desk.sc.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
As noted by Arve and others, since wall time can jump backwards, it is
difficult to use for input because one cannot determine if one event
occurred before another or for how long a key was pressed.
However, the timestamp field is part of the kernel ABI, and cannot be
changed without possibly breaking existing users.
This patch adds a new IOCTL that allows a clockid to be set in the
evdev_client struct that will specify which time base to use for event
timestamps (ie: CLOCK_MONOTONIC instead of CLOCK_REALTIME).
For now we only support CLOCK_MONOTONIC and CLOCK_REALTIME, but
in the future we could support other clockids if appropriate.
The default remains CLOCK_REALTIME, so we don't change the ABI.
Signed-off-by: John Stultz <john.stultz@linaro.org>
Reviewed-by: Daniel Kurtz <djkurtz@google.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
CC: Thomas Gleixner <tglx@linutronix.de>
CC: Eric Dumazet <eric.dumazet@gmail.com>
CC: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Keep all the interesting data in a single cache line.
CC: Thomas Gleixner <tglx@linutronix.de>
CC: Eric Dumazet <eric.dumazet@gmail.com>
CC: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Now that ntp.c's locking is reworked, we can remove most
of the xtime_lock usage in timekeeping.c
The remaining xtime_lock presence is really for jiffies access
and the global load calculation.
CC: Thomas Gleixner <tglx@linutronix.de>
CC: Eric Dumazet <eric.dumazet@gmail.com>
CC: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Use a ntp_lock spin lock to replace xtime_lock locking in ntp.c
CC: Thomas Gleixner <tglx@linutronix.de>
CC: Eric Dumazet <eric.dumazet@gmail.com>
CC: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Currently the NTP managed tick_length value is accessed globally,
in preparations for locking cleanups, make sure it is accessed via
a function and mark it as static.
CC: Thomas Gleixner <tglx@linutronix.de>
CC: Eric Dumazet <eric.dumazet@gmail.com>
CC: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Move ntp_sycned to ntp.c and mark time_status as static.
Also yank function declaration for non-existant function.
CC: Thomas Gleixner <tglx@linutronix.de>
CC: Eric Dumazet <eric.dumazet@gmail.com>
CC: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Now that all the timekeeping variables are stored in
the timekeeper structure, add a new lock to protect the
structure.
For now, this lock nests under the xtime_lock for writes.
For readers, we don't need to take xtime_lock anymore.
CC: Thomas Gleixner <tglx@linutronix.de>
CC: Eric Dumazet <eric.dumazet@gmail.com>
CC: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Move global xtime_lock and timekeeping_suspended values up
to the top of timekeeping.c
CC: Thomas Gleixner <tglx@linutronix.de>
CC: Eric Dumazet <eric.dumazet@gmail.com>
CC: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: John Stultz <john.stultz@linaro.org>
In preparation for locking cleanups, move raw_time into
timekeeper structure.
CC: Thomas Gleixner <tglx@linutronix.de>
CC: Eric Dumazet <eric.dumazet@gmail.com>
CC: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: John Stultz <john.stultz@linaro.org>
In preparation for locking cleanups, move xtime into
timekeeper structure.
CC: Thomas Gleixner <tglx@linutronix.de>
CC: Eric Dumazet <eric.dumazet@gmail.com>
CC: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: John Stultz <john.stultz@linaro.org>
In preparation for locking cleanups, move wall_to_monotonic
into the timekeeper structure.
CC: Thomas Gleixner <tglx@linutronix.de>
CC: Eric Dumazet <eric.dumazet@gmail.com>
CC: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Move total_sleep_time into the timekeeper structure in preparation
for locking cleanups
CC: Thomas Gleixner <tglx@linutronix.de>
CC: Eric Dumazet <eric.dumazet@gmail.com>
CC: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: John Stultz <john.stultz@linaro.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (53 commits)
Kconfig: acpi: Fix typo in comment.
misc latin1 to utf8 conversions
devres: Fix a typo in devm_kfree comment
btrfs: free-space-cache.c: remove extra semicolon.
fat: Spelling s/obsolate/obsolete/g
SCSI, pmcraid: Fix spelling error in a pmcraid_err() call
tools/power turbostat: update fields in manpage
mac80211: drop spelling fix
types.h: fix comment spelling for 'architectures'
typo fixes: aera -> area, exntension -> extension
devices.txt: Fix typo of 'VMware'.
sis900: Fix enum typo 'sis900_rx_bufer_status'
decompress_bunzip2: remove invalid vi modeline
treewide: Fix comment and string typo 'bufer'
hyper-v: Update MAINTAINERS
treewide: Fix typos in various parts of the kernel, and fix some comments.
clockevents: drop unknown Kconfig symbol GENERIC_CLOCKEVENTS_MIGR
gpio: Kconfig: drop unknown symbol 'CS5535_GPIO'
leds: Kconfig: Fix typo 'D2NET_V2'
sound: Kconfig: drop unknown symbol ARCH_CLPS7500
...
Fix up trivial conflicts in arch/powerpc/platforms/40x/Kconfig (some new
kconfig additions, close to removed commented-out old ones)
* 'driver-core-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (73 commits)
arm: fix up some samsung merge sysdev conversion problems
firmware: Fix an oops on reading fw_priv->fw in sysfs loading file
Drivers:hv: Fix a bug in vmbus_driver_unregister()
driver core: remove __must_check from device_create_file
debugfs: add missing #ifdef HAS_IOMEM
arm: time.h: remove device.h #include
driver-core: remove sysdev.h usage.
clockevents: remove sysdev.h
arm: convert sysdev_class to a regular subsystem
arm: leds: convert sysdev_class to a regular subsystem
kobject: remove kset_find_obj_hinted()
m86k: gpio - convert sysdev_class to a regular subsystem
mips: txx9_sram - convert sysdev_class to a regular subsystem
mips: 7segled - convert sysdev_class to a regular subsystem
sh: dma - convert sysdev_class to a regular subsystem
sh: intc - convert sysdev_class to a regular subsystem
power: suspend - convert sysdev_class to a regular subsystem
power: qe_ic - convert sysdev_class to a regular subsystem
power: cmm - convert sysdev_class to a regular subsystem
s390: time - convert sysdev_class to a regular subsystem
...
Fix up conflicts with 'struct sysdev' removal from various platform
drivers that got changed:
- arch/arm/mach-exynos/cpu.c
- arch/arm/mach-exynos/irq-eint.c
- arch/arm/mach-s3c64xx/common.c
- arch/arm/mach-s3c64xx/cpu.c
- arch/arm/mach-s5p64x0/cpu.c
- arch/arm/mach-s5pv210/common.c
- arch/arm/plat-samsung/include/plat/cpu.h
- arch/powerpc/kernel/sysfs.c
and fix up cpu_is_hotpluggable() as per Greg in include/linux/cpu.h
This resolves the conflict in the arch/arm/mach-s3c64xx/s3c6400.c file,
and it fixes the build error in the arch/x86/kernel/microcode_core.c
file, that the merge did not catch.
The microcode_core.c patch was provided by Stephen Rothwell
<sfr@canb.auug.org.au> who was invaluable in the merge issues involved
with the large sysdev removal process in the driver-core tree.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* 'sched-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (40 commits)
sched/tracing: Add a new tracepoint for sleeptime
sched: Disable scheduler warnings during oopses
sched: Fix cgroup movement of waking process
sched: Fix cgroup movement of newly created process
sched: Fix cgroup movement of forking process
sched: Remove cfs bandwidth period check in tg_set_cfs_period()
sched: Fix load-balance lock-breaking
sched: Replace all_pinned with a generic flags field
sched: Only queue remote wakeups when crossing cache boundaries
sched: Add missing rcu_dereference() around ->real_parent usage
[S390] fix cputime overflow in uptime_proc_show
[S390] cputime: add sparse checking and cleanup
sched: Mark parent and real_parent as __rcu
sched, nohz: Fix missing RCU read lock
sched, nohz: Set the NOHZ_BALANCE_KICK flag for idle load balancer
sched, nohz: Fix the idle cpu check in nohz_idle_balance
sched: Use jump_labels for sched_feat
sched/accounting: Fix parameter passing in task_group_account_field
sched/accounting: Fix user/system tick double accounting
sched/accounting: Re-use scheduler statistics for the root cgroup
...
Fix up conflicts in
- arch/ia64/include/asm/cputime.h, include/asm-generic/cputime.h
usecs_to_cputime64() vs the sparse cleanups
- kernel/sched/fair.c, kernel/time/tick-sched.c
scheduler changes in multiple branches
* 'core-rcu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (64 commits)
cpu: Export cpu_up()
rcu: Apply ACCESS_ONCE() to rcu_boost() return value
Revert "rcu: Permit rt_mutex_unlock() with irqs disabled"
docs: Additional LWN links to RCU API
rcu: Augment rcu_batch_end tracing for idle and callback state
rcu: Add rcutorture tests for srcu_read_lock_raw()
rcu: Make rcutorture test for hotpluggability before offlining CPUs
driver-core/cpu: Expose hotpluggability to the rest of the kernel
rcu: Remove redundant rcu_cpu_stall_suppress declaration
rcu: Adaptive dyntick-idle preparation
rcu: Keep invoking callbacks if CPU otherwise idle
rcu: Irq nesting is always 0 on rcu_enter_idle_common
rcu: Don't check irq nesting from rcu idle entry/exit
rcu: Permit dyntick-idle with callbacks pending
rcu: Document same-context read-side constraints
rcu: Identify dyntick-idle CPUs on first force_quiescent_state() pass
rcu: Remove dynticks false positives and RCU failures
rcu: Reduce latency of rcu_prepare_for_idle()
rcu: Eliminate RCU_FAST_NO_HZ grace-period hang
rcu: Avoid needlessly IPIing CPUs at GP end
...
This isn't needed in the clockevents.c file, and the header file is
going away soon, so just remove the #include
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
After all sysdev classes are ported to regular driver core entities, the
sysdev implementation will be entirely removed from the kernel.
Cc: John Stultz <johnstul@us.ibm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Those two APIs were provided to optimize the calls of
tick_nohz_idle_enter() and rcu_idle_enter() into a single
irq disabled section. This way no interrupt happening in-between would
needlessly process any RCU job.
Now we are talking about an optimization for which benefits
have yet to be measured. Let's start simple and completely decouple
idle rcu and dyntick idle logics to simplify.
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
It is assumed that rcu won't be used once we switch to tickless
mode and until we restart the tick. However this is not always
true, as in x86-64 where we dereference the idle notifiers after
the tick is stopped.
To prepare for fixing this, add two new APIs:
tick_nohz_idle_enter_norcu() and tick_nohz_idle_exit_norcu().
If no use of RCU is made in the idle loop between
tick_nohz_enter_idle() and tick_nohz_exit_idle() calls, the arch
must instead call the new *_norcu() version such that the arch doesn't
need to call rcu_idle_enter() and rcu_idle_exit().
Otherwise the arch must call tick_nohz_enter_idle() and
tick_nohz_exit_idle() and also call explicitly:
- rcu_idle_enter() after its last use of RCU before the CPU is put
to sleep.
- rcu_idle_exit() before the first use of RCU after the CPU is woken
up.
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: Guan Xuetao <gxt@mprc.pku.edu.cn>
Cc: David Miller <davem@davemloft.net>
Cc: Chris Metcalf <cmetcalf@tilera.com>
Cc: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
The tick_nohz_stop_sched_tick() function, which tries to delay
the next timer tick as long as possible, can be called from two
places:
- From the idle loop to start the dytick idle mode
- From interrupt exit if we have interrupted the dyntick
idle mode, so that we reprogram the next tick event in
case the irq changed some internal state that requires this
action.
There are only few minor differences between both that
are handled by that function, driven by the ts->inidle
cpu variable and the inidle parameter. The whole guarantees
that we only update the dyntick mode on irq exit if we actually
interrupted the dyntick idle mode, and that we enter in RCU extended
quiescent state from idle loop entry only.
Split this function into:
- tick_nohz_idle_enter(), which sets ts->inidle to 1, enters
dynticks idle mode unconditionally if it can, and enters into RCU
extended quiescent state.
- tick_nohz_irq_exit() which only updates the dynticks idle mode
when ts->inidle is set (ie: if tick_nohz_idle_enter() has been called).
To maintain symmetry, tick_nohz_restart_sched_tick() has been renamed
into tick_nohz_idle_exit().
This simplifies the code and micro-optimize the irq exit path (no need
for local_irq_save there). This also prepares for the split between
dynticks and rcu extended quiescent state logics. We'll need this split to
further fix illegal uses of RCU in extended quiescent states in the idle
loop.
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: Guan Xuetao <gxt@mprc.pku.edu.cn>
Cc: David Miller <davem@davemloft.net>
Cc: Chris Metcalf <cmetcalf@tilera.com>
Cc: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Earlier versions of RCU used the scheduling-clock tick to detect idleness
by checking for the idle task, but handled idleness differently for
CONFIG_NO_HZ=y. But there are now a number of uses of RCU read-side
critical sections in the idle task, for example, for tracing. A more
fine-grained detection of idleness is therefore required.
This commit presses the old dyntick-idle code into full-time service,
so that rcu_idle_enter(), previously known as rcu_enter_nohz(), is
always invoked at the beginning of an idle loop iteration. Similarly,
rcu_idle_exit(), previously known as rcu_exit_nohz(), is always invoked
at the end of an idle-loop iteration. This allows the idle task to
use RCU everywhere except between consecutive rcu_idle_enter() and
rcu_idle_exit() calls, in turn allowing architecture maintainers to
specify exactly where in the idle loop that RCU may be used.
Because some of the userspace upcall uses can result in what looks
to RCU like half of an interrupt, it is not possible to expect that
the irq_enter() and irq_exit() hooks will give exact counts. This
patch therefore expands the ->dynticks_nesting counter to 64 bits
and uses two separate bitfields to count process/idle transitions
and interrupt entry/exit transitions. It is presumed that userspace
upcalls do not happen in the idle loop or from usermode execution
(though usermode might do a system call that results in an upcall).
The counter is hard-reset on each process/idle transition, which
avoids the interrupt entry/exit error from accumulating. Overflow
is avoided by the 64-bitness of the ->dyntick_nesting counter.
This commit also adds warnings if a non-idle task asks RCU to enter
idle state (and these checks will need some adjustment before applying
Frederic's OS-jitter patches (http://lkml.org/lkml/2011/10/7/246).
In addition, validation of ->dynticks and ->dynticks_nesting is added.
Signed-off-by: Paul E. McKenney <paul.mckenney@linaro.org>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
The expiry function compares the timer against current time and does
not expire the timer when the expiry time is >= now. That's wrong. If
the timer is set for now, then it must expire.
Make the condition expiry > now for breaking out the loop.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: John Stultz <john.stultz@linaro.org>
Cc: stable@kernel.org
Introduce nr_busy_cpus in the struct sched_group_power [Not in sched_group
because sched groups are duplicated for the SD_OVERLAP scheduler domain]
and for each cpu that enters and exits idle, this parameter will
be updated in each scheduler group of the scheduler domain that this cpu
belongs to.
To avoid the frequent update of this state as the cpu enters
and exits idle, the update of the stat during idle exit is
delayed to the first timer tick that happens after the cpu becomes busy.
This is done using NOHZ_IDLE flag in the struct rq's nohz_flags.
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/20111202010832.555984323@sbsiddha-desk.sc.intel.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
clockevents: Set noop handler in clockevents_exchange_device()
tick-broadcast: Stop active broadcast device when replacing it
clocksource: Fix bug with max_deferment margin calculation
rtc: Fix some bugs that allowed accumulating time drift in suspend/resume
rtc: Disable the alarm in the hardware
If a device is shutdown, then there might be a pending interrupt,
which will be processed after we reenable interrupts, which causes the
original handler to be run. If the old handler is the (broadcast)
periodic handler the shutdown state might hang the kernel completely.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org
When a better rated broadcast device is installed, then the current
active device is not disabled, which results in two running broadcast
devices.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org
In order to leave a margin of 12.5% we should >> 3 not >> 5.
CC: stable@kernel.org
Signed-off-by: Yang Honggang (Joseph) <eagle.rtlinux@gmail.com>
[jstultz: Modified commit subject]
Signed-off-by: John Stultz <john.stultz@linaro.org>
There's no Kconfig symbol GENERIC_CLOCKEVENTS_MIGR, so the check for it
will always fail.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
hrtimer: Fix extra wakeups from __remove_hrtimer()
timekeeping: add arch_offset hook to ktime_get functions
clocksource: Avoid selecting mult values that might overflow when adjusted
time: Improve documentation of timekeeeping_adjust()
Fixup spelling issues caught by Richard
CC: Richard Cochran <richardcochran@gmail.com>
CC: Chen Jie <chenj@lemote.com>
CC: Steven Rostedt <rostedt@goodmis.org>
CC: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: John Stultz <john.stultz@linaro.org>
The whole point of this function is to return a value not touched by
NTP; unfortunately the comment got copied wholesale without adjustment
from the timekeeping_get_ns function above.
Signed-off-by: Dan McGee <dpmcgee@gmail.com>
Signed-off-by: John Stultz <john.stultz@linaro.org>
ktime_get and ktime_get_ts were calling timekeeping_get_ns()
but later they were not calling arch_gettimeoffset() so architectures
using this mechanism returned 0 ns when calling these functions.
This happened for example when running Busybox's ping which calls
syscall(__NR_clock_gettime, CLOCK_MONOTONIC, ts) which eventually
calls ktime_get. As a result the returned ping travel time was zero.
CC: stable@kernel.org
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
Signed-off-by: John Stultz <john.stultz@linaro.org>
For some frequencies, the clocks_calc_mult_shift() function will
unfortunately select mult values very close to 0xffffffff. This
has the potential to overflow when NTP adjusts the clock, adding
to the mult value.
This patch adds a clocksource.maxadj value, which provides
an approximation of an 11% adjustment(NTP limits adjustments to
500ppm and the tick adjustment is limited to 10%), which could
be made to the clocksource.mult value. This is then used to both
check that the current mult value won't overflow/underflow, as
well as warning us if the timekeeping_adjust() code pushes over
that 11% boundary.
v2: Fix max_adjustment calculation, and improve WARN_ONCE
messages.
v3: Don't warn before maxadj has actually been set
CC: Yong Zhang <yong.zhang0@gmail.com>
CC: David Daney <ddaney.cavm@gmail.com>
CC: Thomas Gleixner <tglx@linutronix.de>
CC: Chen Jie <chenj@lemote.com>
CC: zhangfx <zhangfx@lemote.com>
CC: stable@kernel.org
Reported-by: Chen Jie <chenj@lemote.com>
Reported-by: zhangfx <zhangfx@lemote.com>
Tested-by: Yong Zhang <yong.zhang0@gmail.com>
Signed-off-by: John Stultz <john.stultz@linaro.org>
These files were getting <linux/module.h> via an implicit non-obvious
path, but we want to crush those out of existence since they cost
time during compiles of processing thousands of lines of headers
for no reason. Give them the lightweight header that just contains
the EXPORT_SYMBOL infrastructure.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
After getting a number of questions in private emails about the
math around admittedly very complex timekeeping_adjust() and
timekeeping_big_adjust(), I figure the code needs some better
comments.
Hopefully the explanations are clear enough and don't muddy the
water any worse.
Still needs documentation for ntp_error, but I couldn't recall
exactly the full explanation behind the code that's there
(although I do recall once working it out when Roman first
proposed it). Given a bit more time I can probably work it out,
but I don't want to hold back this documentation until then.
Signed-off-by: John Stultz <john.stultz@linaro.org>
Cc: Chen Jie <chenj@lemote.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Link: http://lkml.kernel.org/r/1319764362-32367-1-git-send-email-john.stultz@linaro.org
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (23 commits)
time, s390: Get rid of compile warning
dw_apb_timer: constify clocksource name
time: Cleanup old CONFIG_GENERIC_TIME references that snuck in
time: Change jiffies_to_clock_t() argument type to unsigned long
alarmtimers: Fix error handling
clocksource: Make watchdog reset lockless
posix-cpu-timers: Cure SMP accounting oddities
s390: Use direct ktime path for s390 clockevent device
clockevents: Add direct ktime programming function
clockevents: Make minimum delay adjustments configurable
nohz: Remove "Switched to NOHz mode" debugging messages
proc: Consider NO_HZ when printing idle and iowait times
nohz: Make idle/iowait counter update conditional
nohz: Fix update_ts_time_stat idle accounting
cputime: Clean up cputime_to_usecs and usecs_to_cputime macros
alarmtimers: Rework RTC device selection using class interface
alarmtimers: Add try_to_cancel functionality
alarmtimers: Add more refined alarm state tracking
alarmtimers: Remove period from alarm structure
alarmtimers: Remove interval cap limit hack
...
* 'core-rcu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (45 commits)
rcu: Move propagation of ->completed from rcu_start_gp() to rcu_report_qs_rsp()
rcu: Remove rcu_needs_cpu_flush() to avoid false quiescent states
rcu: Wire up RCU_BOOST_PRIO for rcutree
rcu: Make rcu_torture_boost() exit loops at end of test
rcu: Make rcu_torture_fqs() exit loops at end of test
rcu: Permit rt_mutex_unlock() with irqs disabled
rcu: Avoid having just-onlined CPU resched itself when RCU is idle
rcu: Suppress NMI backtraces when stall ends before dump
rcu: Prohibit grace periods during early boot
rcu: Simplify unboosting checks
rcu: Prevent early boot set_need_resched() from __rcu_pending()
rcu: Dump local stack if cannot dump all CPUs' stacks
rcu: Move __rcu_read_unlock()'s barrier() within if-statement
rcu: Improve rcu_assign_pointer() and RCU_INIT_POINTER() documentation
rcu: Make rcu_assign_pointer() unconditionally insert a memory barrier
rcu: Make rcu_implicit_dynticks_qs() locals be correct size
rcu: Eliminate in_irq() checks in rcu_enter_nohz()
nohz: Remove nohz_cpu_mask
rcu: Document interpretation of RCU-lockdep splats
rcu: Allow rcutorture's stat_interval parameter to be changed at runtime
...
RCU no longer uses this global variable, nor does anyone else. This
commit therefore removes this variable. This reduces memory footprint
and also removes some atomic instructions and memory barriers from
the dyntick-idle path.
Signed-off-by: Alex Shi <alex.shi@intel.com>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
commit 8bc0daf (alarmtimers: Rework RTC device selection using class
interface) did not implement required error checks. Add them.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The table_lock lock can be taken in atomic context and therefore
cannot be preempted on -rt - annotate it.
In mainline this change documents the low level nature of
the lock - otherwise there's no functional difference. Lockdep
and Sparse checking will work as usual.
Reported-by: Andreas Sundebo <kernel@sundebo.dk>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Andreas Sundebo <kernel@sundebo.dk>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
KGDB needs to trylock watchdog_lock when trying to reset the
clocksource watchdog after the system has been stopped to avoid a
potential deadlock. When the trylock fails TSC usually becomes
unstable.
We can be more clever by using an atomic counter and checking it in
the clocksource_watchdog callback. We restart the watchdog whenever
the counter is > 0 and only decrement the counter when we ran through
a full update cycle.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: John Stultz <johnstul@us.ibm.com>
Acked-by: Jason Wessel <jason.wessel@windriver.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/alpine.LFD.2.02.1109121326280.2723@ionos
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
There is at least one architecture (s390) with a sane clockevent device
that can be programmed with the equivalent of a ktime. No need to create
a delta against the current time, the ktime can be used directly.
A new clock device function 'set_next_ktime' is introduced that is called
with the unmodified ktime for the timer if the clock event device has the
CLOCK_EVT_FEAT_KTIME bit set.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: john stultz <johnstul@us.ibm.com>
Link: http://lkml.kernel.org/r/20110823133142.815350967@de.ibm.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The automatic increase of the min_delta_ns of a clockevents device
should be done in the clockevents code as the minimum delay is an
attribute of the clockevents device.
In addition not all architectures want the automatic adjustment, on a
massively virtualized system it can happen that the programming of a
clock event fails several times in a row because the virtual cpu has
been rescheduled quickly enough. In that case the minimum delay will
erroneously be increased with no way back. The new config symbol
GENERIC_CLOCKEVENTS_MIN_ADJUST is used to enable the automatic
adjustment. The config option is selected only for x86.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: john stultz <johnstul@us.ibm.com>
Link: http://lkml.kernel.org/r/20110823133142.494157493@de.ibm.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
When performing cpu hotplug tests the kernel printk log buffer gets flooded
with pointless "Switched to NOHz mode..." messages. Especially when afterwards
analyzing a dump this might have removed more interesting stuff out of the
buffer.
Assuming that switching to NOHz mode simply works just remove the printk.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Link: http://lkml.kernel.org/r/20110823112046.GB2540@osiris.boeblingen.de.ibm.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
get_cpu_{idle,iowait}_time_us update idle/iowait counters
unconditionally if the given CPU is in the idle loop.
This doesn't work well outside of CPU governors which are singletons
so nobody (except for IRQ) can race with them.
We will need to use both functions from /proc/stat handler to properly
handle nohz idle/iowait times.
Make the update depend on a non NULL last_update_time argument.
Signed-off-by: Michal Hocko <mhocko@suse.cz>
Cc: Dave Jones <davej@redhat.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Link: http://lkml.kernel.org/r/11f23179472635ce52e78921d47a20216b872f23.1314172057.git.mhocko@suse.cz
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
update_ts_time_stat currently updates idle time even if we are in
iowait loop at the moment. The only real users of the idle counter
(via get_cpu_idle_time_us) are CPU governors and they expect to get
cumulative time for both idle and iowait times.
The value (idle_sleeptime) is also printed to userspace by print_cpu
but it prints both idle and iowait times so the idle part is misleading.
Let's clean this up and fix update_ts_time_stat to account both counters
properly and update consumers of idle to consider iowait time as well.
If we do this we might use get_cpu_{idle,iowait}_time_us from other
contexts as well and we will get expected values.
Signed-off-by: Michal Hocko <mhocko@suse.cz>
Cc: Dave Jones <davej@redhat.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Link: http://lkml.kernel.org/r/e9c909c221a8da402c4da07e4cd968c3218f8eb1.1314172057.git.mhocko@suse.cz
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This allows cleaner detection of the RTC device being registered, rather
then probing any time someone calls alarmtimer_get_rtcdev.
CC: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: John Stultz <john.stultz@linaro.org>
There's a number of edge cases when cancelling a alarm, so
to be sure we accurately do so, introduce try_to_cancel, which
returns proper failure errors if it cannot. Also modify cancel
to spin until the alarm is properly disabled.
CC: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: John Stultz <john.stultz@linaro.org>
In order to allow for functionality like try_to_cancel, add
more refined state tracking (similar to hrtimers).
CC: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Now that periodic alarmtimers are managed by the handler function,
remove the period value from the alarm structure and let the handlers
manage the interval on their own.
CC: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Now that the alarmtimers code has been refactored, the interval
cap limit can be removed.
CC: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: John Stultz <john.stultz@linaro.org>
In order to avoid wasting time expiring and re-adding very high freq
periodic alarmtimers, introduce alarm_forward() which is similar to
hrtimer_forward and moves the timer to the next future expiration time
and returns the number of overruns.
CC: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: John Stultz <john.stultz@linaro.org>
This patch pushes the periodic alarmtimer re-arming down into the alarmtimer
handler, mimicking how hrtimers handle this.
CC: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: John Stultz <john.stultz@linaro.org>
In order to properly fix the denial of service issue with high freq
periodic alarm timers, we need to push the re-arming logic into the
alarm timer handler, much as the hrtimer code does.
This patch introduces alarmtimer_restart enum and changes the
alarmtimer handler declarations to use it as a return value. Further,
to ease following changes, it extends the alarmtimer handler functions
to also take the time at expiration. No logic is yet modified.
CC: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Its possible to jam up the alarm timers by setting very small interval
timers, which will cause the alarmtimer subsystem to spend all of its time
firing and restarting timers. This can effectivly lock up a box.
A deeper fix is needed, closely mimicking the hrtimer code, but for now
just cap the interval to 100us to avoid userland hanging the system.
CC: Thomas Gleixner <tglx@linutronix.de>
CC: stable@kernel.org
Signed-off-by: John Stultz <john.stultz@linaro.org>
Following common_timer_get, zero out the itimerspec passed in.
CC: Thomas Gleixner <tglx@linutronix.de>
CC: stable@kernel.org
Signed-off-by: John Stultz <john.stultz@linaro.org>
We don't check if old_setting is non null before assigning it, so
correct this.
CC: Thomas Gleixner <tglx@linutronix.de>
CC: stable@kernel.org
Signed-off-by: John Stultz <john.stultz@linaro.org>
Terribly embarassing. Don't know how I committed this, but its
KERN_WARNING not KERN_WARN.
This fixes the following compile error:
kernel/time/timekeeping.c: In function ‘__timekeeping_inject_sleeptime’:
kernel/time/timekeeping.c:608: error: ‘KERN_WARN’ undeclared (first use in this function)
kernel/time/timekeeping.c:608: error: (Each undeclared identifier is reported only once
kernel/time/timekeeping.c:608: error: for each function it appears in.)
kernel/time/timekeeping.c:608: error: expected ‘)’ before string constant
make[2]: *** [kernel/time/timekeeping.o] Error 1
Reported-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Because the read_persistent_clock interface is usually backed by
only a second granular interface, each time we read from the persistent
clock for suspend/resume, we introduce a half second (on average) of error.
In order to avoid this error accumulating as the system is suspended
over and over, this patch measures the time delta between the persistent
clock and the system CLOCK_REALTIME.
If the delta is less then 2 seconds from the last suspend, we compensate
by using the previous time delta (keeping it close). If it is larger
then 2 seconds, we assume the clock was set or has been changed, so we
do no correction and update the delta.
Note: If NTP is running, ths could seem to "fight" with the NTP corrected
time, where as if the system time was off by 1 second, and NTP slewed the
value in, a suspend/resume cycle could undo this correction, by trying to
restore the previous offset from the persistent clock. However, without
this patch, since each read could cause almost a full second worth of
error, its possible to get almost 2 seconds of error just from the
suspend/resume cycle alone, so this about equal to any offset added by
the compensation.
Further on systems that suspend/resume frequently, this should keep time
closer then NTP could compensate for if the errors were allowed to
accumulate.
Credits to Arve Hjønnevåg for suggesting this solution.
CC: Arve Hjønnevåg <arve@android.com>
CC: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Arve suggested making sure we catch possible negative sleep time
intervals that could be passed into timekeeping_inject_sleeptime.
CC: Arve Hjønnevåg <arve@android.com>
CC: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Toralf Förster and Richard Weinberger noted that if there is
no RTC device, the alarm timers core prints out an annoying
"ALARM timers will not wake from suspend" message.
This warning has been removed in a previous patch, however
the issue still remains: The original idea was to support
alarm timers even if there was no rtc device, as long as the
system didn't go into suspend.
However, after further consideration, communicating to the application
that alarmtimers are not fully functional seems like the better
solution.
So this patch makes it so we return -ENOTSUPP to any posix _ALARM
clockid calls if there is no backing RTC device on the system.
Further this changes the behavior where when there is no rtc device
we will check for one on clock_getres, clock_gettime, timer_create,
and timer_nsleep instead of on suspend.
CC: Toralf Förster <toralf.foerster@gmx.de>
CC: Richard Weinberger <richard@nod.at
CC: Peter Zijlstra <peterz@infradead.org>
CC: Thomas Gleixner <tglx@linutronix.de>
Reported-by: Toralf Förster <toralf.foerster@gmx.de>
Reported by: Richard Weinberger <richard@nod.at>
Signed-off-by: John Stultz <john.stultz@linaro.org>
The alarmtimers code currently picks a rtc device to use at
late init time. However, if your rtc driver is loaded as a module,
it may be registered after the alarmtimers late init code, leaving
the alarmtimers nonfunctional.
This patch moves the the rtcdevice selection to when we actually try
to use it, allowing us to make use of rtc modules that may have been
loaded at any point since bootup.
CC: Thomas Gleixner <tglx@linutronix.de>
CC: Meelis Roos <mroos@ut.ee>
Reported-by: Meelis Roos <mroos@ut.ee>
Signed-off-by: John Stultz <john.stultz@linaro.org>
The clocksource watchdog code is interruptible and it has been
observed that this can trigger false positives which disable the TSC.
The reason is that an interrupt storm or a long running interrupt
handler between the read of the watchdog source and the read of the
TSC brings the two far enough apart that the delta is larger than the
unstable treshold. Move both reads into a short interrupt disabled
region to avoid that.
Reported-and-tested-by: Vernon Mauery <vernux@us.ibm.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@kernel.org
For UP it's stupid to request an initialized cpumask for the clock
event devices. Though we need the mask set even on UP to avoid a
horrible ifdeffery especially in the broadcast code.
For SMP we can at least try to survive with a warning and set the
cpumask of the cpu we're running on. That gives a decent chance to
bring the machine up and retrieve the debug info.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Linus Walleij <linus.walleij@linaro.org
Cc: Lee Jones <lee.jones@linaro.org>
Cc: Russell King - ARM Linux <linux@arm.linux.org.uk>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Instead of iterating over all possible timer bases avoid it by marking
the active bases in the cpu base.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Peter Zijlstra <peterz@infradead.org>
* 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
hrtimer: Make lookup table const
RTC: Disable CONFIG_RTC_CLASS from being built as a module
timers: Fix alarmtimer build issues when CONFIG_RTC_CLASS=n
timers: Remove delayed irqwork from alarmtimers implementation
timers: Improve alarmtimer comments and minor fixes
timers: Posix interface for alarm-timers
timers: Introduce in-kernel alarm-timer interface
timers: Add rb_init_node() to allow for stack allocated rb nodes
time: Add timekeeping_inject_sleeptime
* 'timers-clockevents-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: hpet: Cleanup the clockevents init and register code
x86: Convert PIT to clockevents_config_and_register()
clockevents: Provide interface to reconfigure an active clock event device
clockevents: Provide combined configure and register function
clockevents: Restructure clock_event_device members
clocksource: Get rid of the hardcoded 5 seconds sleep time limit
clocksource: Restructure clocksource struct members
Some ARM SoCs have clock event devices which have their frequency
modified due to frequency scaling. Provide an interface which allows
to reconfigure an active device. After reconfiguration reprogram the
current pending event.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: LAK <linux-arm-kernel@lists.infradead.org>
Cc: John Stultz <john.stultz@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Ingo Molnar <mingo@elte.hu>
Link: http://lkml.kernel.org/r/%3C20110518210136.437459958%40linutronix.de%3E
All clockevent devices have the same open coded initialization
functions. Provide an interface which does all necessary
initialization in the core code.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: John Stultz <john.stultz@linaro.org>
Reviewed-by: Ingo Molnar <mingo@elte.hu>
Link: http://lkml.kernel.org/r/%3C20110518210136.331975870%40linutronix.de%3E
Slow clocksources can have a way longer sleep time than 5 seconds and
even fast ones can easily cope with 600 seconds and still maintain
proper accuracy.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: John Stultz <john.stultz@linaro.org>
Reviewed-by: Ingo Molnar <mingo@elte.hu>
Link: http://lkml.kernel.org/r/%3C20110518210136.109811585%40linutronix.de%3E
The first cpu which switches from periodic to oneshot mode switches
also the broadcast device into oneshot mode. The broadcast device
serves as a backup for per cpu timers which stop in deeper
C-states. To avoid starvation of the cpus which might be in idle and
depend on broadcast mode it marks the other cpus as broadcast active
and sets the brodcast expiry value of those cpus to the next tick.
The oneshot mode broadcast bit for the other cpus is sticky and gets
only cleared when those cpus exit idle. If a cpu was not idle while
the bit got set in consequence the bit prevents that the broadcast
device is armed on behalf of that cpu when it enters idle for the
first time after it switched to oneshot mode.
In most cases that goes unnoticed as one of the other cpus has usually
a timer pending which keeps the broadcast device armed with a short
timeout. Now if the only cpu which has a short timer active has the
bit set then the broadcast device will not be armed on behalf of that
cpu and will fire way after the expected timer expiry. In the case of
Christians bug report it took ~145 seconds which is about half of the
wrap around time of HPET (the limit for that device) due to the fact
that all other cpus had no timers armed which expired before the 145
seconds timeframe.
The solution is simply to clear the broadcast active bit
unconditionally when a cpu switches to oneshot mode after the first
cpu switched the broadcast device over. It's not idle at that point
otherwise it would not be executing that code.
[ I fundamentally hate that broadcast crap. Why the heck thought some
folks that when going into deep idle it's a brilliant concept to
switch off the last device which brings the cpu back from that
state? ]
Thanks to Christian for providing all the valuable debug information!
Reported-and-tested-by: Christian Hoffmann <email@christianhoffmann.info>
Cc: John Stultz <johnstul@us.ibm.com>
Link: http://lkml.kernel.org/r/%3Calpine.LFD.2.02.1105161105170.3078%40ionos%3E
Cc: stable@kernel.org
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Avoid taking broadcast_lock in the idle path for systems where the
timer doesn't stop in C3.
[ tglx: Removed the stale label and added comment ]
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Cc: Dave Kleikamp <dkleikamp@gmail.com>
Cc: Chris Mason <chris.mason@oracle.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Tim Chen <tim.c.chen@linux.intel.com>
Cc: lenb@kernel.org
Cc: paulmck@us.ibm.com
Link: http://lkml.kernel.org/r/%3C20110504234806.GF2925%40one.firstfloor.org%3E
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Christian Hoffmann reported that the command line clocksource override
with acpi_pm timer fails:
Kernel command line: <SNIP> clocksource=acpi_pm
hpet clockevent registered
Switching to clocksource hpet
Override clocksource acpi_pm is not HRT compatible.
Cannot switch while in HRT/NOHZ mode.
The watchdog code is what enables CLOCK_SOURCE_VALID_FOR_HRES, but we
actually end up selecting the clocksource before we enqueue it into
the watchdog list, so that's why we see the warning and fail to switch
to acpi_pm timer as requested. That's particularly bad when we want to
debug timekeeping related problems in early boot.
Put the selection call last.
Reported-by: Christian Hoffmann <email@christianhoffmann.info>
Signed-off-by: John Stultz <johnstul@us.ibm.com>
Cc: stable@kernel.org # 32...
Link: http://lkml.kernel.org/r/%3C1304558210.2943.24.camel%40work-vm%3E
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
class_find_device() takes a refcount on the rtc device. rtc_open()
takes another one, so we can drop it after the rtc_open() call.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: John Stultz <john.stultz@linaro.org>
alarmtimer_late_init() uses class_find_device() to find a alarm
capable rtc device. The match callback stores a pointer to the name in
the char pointer handed in from the call site. alarmtimer_late_init()
checks the char pointer for NULL, but the pointer is on the stack and
not initialized to NULL before the call. So it can have random content
when the match function did not identify a device, which leads to
random access in the following rtc_open() call where the pointer is
dereferenced
Instead of relying on the char pointer, check the return value of
class_find_device. If a device is found then the name pointer is valid
as well.
Reported-by: Ingo Molnar <mingo@elte.hu>
Cc: John Stultz <john.stultz@linaro.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Some applications must be aware of clock realtime being set
backward. A simple example is a clock applet which arms a timer for
the next minute display. If clock realtime is set backward then the
applet displays a stale time for the amount of time which the clock
was set backwards. Due to that applications poll the time because we
don't have an interface.
Extend the timerfd interface by adding a flag which puts the timer
onto a different internal realtime clock. All timers on this clock are
expired whenever the clock was set.
The timerfd core records the monotonic offset when the timer is
created. When the timer is armed, then the current offset is compared
to the previous recorded offset. When it has changed, then
timerfd_settime returns -ECANCELED. When a timer is read the offset is
compared and if it changed -ECANCELED returned to user space. Periodic
timers are not rearmed in the cancelation case.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: John Stultz <johnstul@us.ibm.com>
Cc: Chris Friesen <chris.friesen@genband.com>
Tested-by: Kay Sievers <kay.sievers@vrfy.org>
Cc: "Kirill A. Shutemov" <kirill@shutemov.name>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Davide Libenzi <davidel@xmailserver.org>
Reviewed-by: Alexander Shishkin <virtuoso@slind.org>
Link: http://lkml.kernel.org/r/%3Calpine.LFD.2.02.1104271359580.3323%40ionos%3E
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Make clock_was_set() unconditional and rename hres_timers_resume to
hrtimers_resume. This is a preparatory patch for hrtimers which are
cancelled when clock realtime was set.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Ingo pointed out that the alarmtimers won't build if CONFIG_RTC_CLASS=n.
This patch adds proper ifdefs to the alarmtimer code to disable the rtc
usage if it is not built in.
Reported-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Thomas asked about the delayed irq work in the alarmtimers code,
and I realized that it was a legacy from when the alarmtimer base
lock was a mutex (due to concerns that we'd be interacting with
the RTC device, which is protected by mutexes).
Since the alarmtimer base is now protected by a spinlock, we can
simply execute alarmtimer functions directly from the hrtimer
callback. Should any future alarmtimer functions sleep, they can
simply manage scheduling any delayed work themselves.
CC: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: John Stultz <john.stultz@linaro.org>
This patch addresses a number of minor comment improvements and
other minor issues from Thomas' review of the alarmtimers code.
CC: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: John Stultz <john.stultz@linaro.org>
This patch exposes alarm-timers to userland via the posix clock
and timers interface, using two new clockids: CLOCK_REALTIME_ALARM
and CLOCK_BOOTTIME_ALARM. Both clockids behave identically to
CLOCK_REALTIME and CLOCK_BOOTTIME, respectively, but timers
set against the _ALARM suffixed clockids will wake the system if
it is suspended.
Some background can be found here:
https://lwn.net/Articles/429925/
The concept for Alarm-timers was inspired by the Android Alarm
driver (by Arve Hjønnevåg) found in the Android kernel tree.
See: http://android.git.kernel.org/?p=kernel/common.git;a=blob;f=drivers/rtc/alarm.c;h=1250edfbdf3302f5e4ea6194847c6ef4bb7beb1c;hb=android-2.6.36
While the in-kernel interface is pretty similar between
alarm-timers and Android alarm driver, the user-space interface
for the Android alarm driver is via ioctls to a new char device.
As mentioned above, I've instead chosen to export this functionality
via the posix interface, as it seemed a little simpler and avoids
creating duplicate interfaces to things like CLOCK_REALTIME and
CLOCK_MONOTONIC under alternate names (ie:ANDROID_ALARM_RTC and
ANDROID_ALARM_SYSTEMTIME).
The semantics of the Android alarm driver are different from what
this posix interface provides. For instance, threads other then
the thread waiting on the Android alarm driver are able to modify
the alarm being waited on. Also this interface does not allow
the same wakelock semantics that the Android driver provides
(ie: kernel takes a wakelock on RTC alarm-interupt, and holds it
through process wakeup, and while the process runs, until the
process either closes the char device or calls back in to wait
on a new alarm).
One potential way to implement similar semantics may be via
the timerfd infrastructure, but this needs more research.
There may also need to be some sort of sysfs system level policy
hooks that allow alarm timers to be disabled to keep them
from firing at inappropriate times (ie: laptop in a well insulated
bag, mid-flight).
CC: Arve Hjønnevåg <arve@android.com>
CC: Thomas Gleixner <tglx@linutronix.de>
CC: Alessandro Zummo <a.zummo@towertech.it>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Lars-Peter Clausen
Richard Cochran
Chuansheng Liu
Frederic Weisbecker
Linus Torvalds
Dan Carpenter
Paul E. McKenney
John Stultz
Todd Poynor
Paul E. McKenney
Rafael J. Wysocki
Alex Shi
Charles Wang
Andreas Schwab
Ingo Molnar
Thomas Gleixner
John Stultz
Peter Zijlstra
Magnus Damm
Mike Galbraith
Greg Kroah-Hartman
Suresh Siddha
Neal Cardwell
Jim Cromie
Cesar Eduardo Barros
Sasha Levin
Dmitry Torokhov
Michal Hocko
Greg Kroah-Hartman
Kay Sievers
Kusanagi Kouichi
Ingo Molnar
Yang Honggang (Joseph)
Paul Bolle
Dan McGee
Hector Palacios
Paul Gortmaker
Martin Schwidefsky
Heiko Carstens
Andi Kleen