To really make sense of route notifications in the presence of
multiple tables, userspace also needs to be notified about routing
rule updates. Notifications are sent to the so far unused
RTNLGRP_NOP1 (now RTNLGRP_RULE) group.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch turns the RTNL from a semaphore to a new 2.6.16 mutex and
gets rid of some of the leftover legacy.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
this patch adds a dormant flag to network devices, RFC2863 operstate derived
from these flags and possibility for userspace interaction. It allows drivers
to signal that a device is unusable for user traffic without disabling
queueing (and therefore the possibility for protocol establishment traffic to
flow) and a userspace supplicant (WPA, 802.1X) to mark a device unusable
without changes to the driver.
It is the result of our long discussion. However I must admit that it
represents what Jamal and I agreed on with compromises towards Krzysztof, but
Thomas and Krzysztof still disagree with some parts. Anyway I think it should
be applied.
Signed-off-by: Stefan Rompf <stefan@loplof.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
I reported a problem and gave hints to the solution, but nobody seemed
to react. So I prepared a patch against 2.6.14.4.
Tested on 2.6.14.4 with "ip monitor addr" and with the program
attached, while adding and removing IPv6 address. Both programs didn't
receive any messages. Tested 2.6.14.4 + this patch, and both programs
received add and remove messages.
Signed-off-by: Kristian Slavov <kristian.slavov@nomadiclab.com>
Acked-by: Jamal Hadi salim <hadi@cyberus.ca>
ACKed-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Plug holes with padding fields and initialized them to zero.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
To retrieve the neighbour tables send RTM_GETNEIGHTBL with the
NLM_F_DUMP flag set. Every neighbour table configuration is
spread over multiple messages to avoid running into message
size limits on systems with many interfaces. The first message
in the sequence transports all not device specific data such as
statistics, configuration, and the default parameter set.
This message is followed by 0..n messages carrying device
specific parameter sets.
Although the ordering should be sufficient, NDTA_NAME can be
used to identify sequences. The initial message can be identified
by checking for NDTA_CONFIG. The device specific messages do
not contain this TLV but have NDTPA_IFINDEX set to the
corresponding interface index.
To change neighbour table attributes, send RTM_SETNEIGHTBL
with NDTA_NAME set. Changeable attribute include NDTA_THRESH[1-3],
NDTA_GC_INTERVAL, and all TLVs in NDTA_PARMS unless marked
otherwise. Device specific parameter sets can be changed by
setting NDTPA_IFINDEX to the interface index of the corresponding
device.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
RTA_GET_U(32|64)(tlv)
Assumes TLV is a u32/u64 field and returns its value.
RTA_GET_[M]SECS(tlv)
Assumes TLV is a u64 and transports jiffies converted
to seconds or milliseconds and returns its value.
RTA_PUT_U(32|64)(skb, type, value)
Appends %value as fixed u32/u64 to %skb as TLV %type.
RTA_PUT_[M]SECS(skb, type, jiffies)
Converts %jiffies to secs/msecs and appends it as u64
to %skb as TLV %type.
RTA_PUT_STRING(skb, type, string)
Appends %NUL terminated %string to %skb as TLV %type.
RTA_NEST(skb, type)
Starts a nested TLV %type and returns the nesting handle.
RTA_NEST_END(skb, nesting_handle)
Finishes the nested TLV %nesting_handle, must be called
symmetric to RTA_NEST(). Returns skb->len
RTA_NEST_CANCEL(skb, nesting_handle)
Cancel the nested TLV %nesting_handle and trim nested TLV
from skb again, returns -1.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Converts remaining rtnetlink_link tables to use c99 designated
initializers to make greping a little bit easier.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Converts rtm_min and rtm_max arrays to use c99 designated
initializers for easier insertion of new message families.
RTM_GETMULTICAST and RTM_GETANYCAST did not have the minimal
message size specified which means that the netlink message
was parsed for routing attributes starting from the header.
Adds the proper minimal message sizes for these messages
(netlink header + common rtnetlink header) to fix this issue.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
RTM_MAX is currently set to the maximum reserverd message type plus one
thus being the cause of two bugs for new types being assigned a) given the
new family registers only the NEW command in its reserved block the array
size for per family entries is calculated one entry short and b) given the
new family registers all commands RTM_MAX would point to the first entry
of the block following this one and the rtnetlink receive path would accept
a message type for a nonexisting family.
This patch changes RTM_MAX to point to the maximum valid message type
by aligning it to the start of the next block and subtracting one.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.
Let it rip!
Patrick McHardy
Alpt
Stephen Hemminger
Stefan Rompf
Kristian Slavov
Thomas Graf
Linus Torvalds