Commit 18a4d0a22e ("[SCSI] Handle disk devices which can not process
medium access commands") introduced a bug in which we would attempt to
dereference the scsi driver even when the device had no ULD attached.
Ensure that a driver is registered and make the driver accessor function
more resilient to errors during device discovery.
Reported-by: Elric Fu <elricfu1@gmail.com>
Reported-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We have experienced several devices which fail in a fashion we do not
currently handle gracefully in SCSI. After a failure these devices will
respond to the SCSI primary command set (INQUIRY, TEST UNIT READY, etc.)
but any command accessing the storage medium will time out.
The following patch adds an callback that can be used by upper level
drivers to inspect the results of an error handling command. This in
turn has been used to implement additional checking in the SCSI disk
driver.
If a medium access command fails twice but TEST UNIT READY succeeds both
times in the subsequent error handling we will offline the device. The
maximum number of failed commands required to take a device offline can
be tweaked in sysfs.
Also add a new error flag to scsi_debug which allows this scenario to be
easily reproduced.
[jejb: fix up integer parsing to use kstrtouint]
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Resubmitting as my previous post had format issues and did not go llinux-scsi.
This patch changes the function to set_msg_byte, set_host_byte and
set_driver_byte to correctly set the corresponding bytes appropriately.
It will reset the original setting and correctly set it to the new value. The
previous OR operation does not always set it back to new value. Look at patch
2/2 for an example.
Signed-off-by: Babu Moger <babu.moger@netapp.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The checksum format is orthogonal to whether the protection information
is being passed on beyond the HBA or not. It is perfectly valid to use
a non-T10 CRC with WRITE_STRIP and READ_INSERT.
Consequently it no longer makes sense to explicitly refer to the
conversion in the protection operation. Update sd_dif and lpfc
accordingly.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Acked-by: Ihab Hamadi <Ihab.Hamadi@Emulex.Com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
With recent cleanups, there is no place where low level driver
directly manipulates request fields. This means that the 'hard'
request fields always equal the !hard fields. Convert all
rq->sectors, nr_sectors and current_nr_sectors references to
accessors.
While at it, drop superflous blk_rq_pos() < 0 test in swim.c.
[ Impact: use pos and nr_sectors accessors ]
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Tested-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Tested-by: Adrian McMenamin <adrian@mcmen.demon.co.uk>
Acked-by: Adrian McMenamin <adrian@mcmen.demon.co.uk>
Acked-by: Mike Miller <mike.miller@hp.com>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Cc: Borislav Petkov <petkovbb@googlemail.com>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Eric Moore <Eric.Moore@lsi.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: Pete Zaitcev <zaitcev@redhat.com>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Paul Clements <paul.clements@steeleye.com>
Cc: Tim Waugh <tim@cyberelk.net>
Cc: Jeff Garzik <jgarzik@pobox.com>
Cc: Jeremy Fitzhardinge <jeremy@xensource.com>
Cc: Alex Dubov <oakad@yahoo.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Dario Ballabio <ballabio_dario@emc.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: unsik Kim <donari75@gmail.com>
Cc: Laurent Vivier <Laurent@lvivier.info>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
This allows it to compile and be used on the ps3 platform that wants
to use the #define values in scsi.h without actually having
CONFIG_SCSI set.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Right now SCSI and others do their own command timeout handling.
Move those bits to the block layer.
Instead of having a timer per command, we try to be a bit more clever
and simply have one per-queue. This avoids the overhead of having to
tear down and setup a timer for each command, so it will result in a lot
less timer fiddling.
Signed-off-by: Mike Anderson <andmike@linux.vnet.ibm.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Implement support for DMA of protection information for devices that
are data integrity capable.
- Add support for mapping an extra scatter-gather list containing
the protection information.
- Allocate protection scsi_data_buffer if host is DIX (integrity DMA)
capable.
- Accessor function for checking whether a device has protection
enabled.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Controllers that support DMA of protection information must be told
explicitly how to handle the I/O. The controller has no knowledge of
the protection capabilities of the target device so this information
must be passed in the scsi_cmnd.
- The protection operation tells the HBA whether to generate, strip or
verify protection information.
- The protection type tells the HBA which layout the target is
formatted with. This is necessary because the controller must be
able to correctly interpret the included protection information in
order to verify it.
- When a scsi_cmnd is reused for error handling the protection
operation must be cleared and saved while error handling is in
progress.
- prot_op and prot_type are placed in an existing hole in scsi_cmnd
and don't cause the structure to grow.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Add support for variable-length, extended, and vendor specific
CDBs to scsi-ml. It is now possible for initiators and ULD's
to issue these types of commands. LLDs need not change much.
All they need is to raise the .max_cmd_len to the longest command
they support (see iscsi patch).
- clean-up some code paths that did not expect commands to be
larger than 16, and change cmd_len members' type to short as
char is not enough.
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Signed-off-by: Benny Halevy <bhalevy@panasas.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
- struct scsi_cmnd had a 16 bytes command buffer of its own.
This is an unnecessary duplication and copy of request's
cmd. It is probably left overs from the time that scsi_cmnd
could function without a request attached. So clean that up.
- Once above is done, few places, apart from scsi-ml, needed
adjustments due to changing the data type of scsi_cmnd->cmnd.
- Lots of drivers still use MAX_COMMAND_SIZE. So I have left
that #define but equate it to BLK_MAX_CDB. The way I see it
and is reflected in the patch below is.
MAX_COMMAND_SIZE - means: The longest fixed-length (*) SCSI CDB
as per the SCSI standard and is not related
to the implementation.
BLK_MAX_CDB. - The allocated space at the request level
- I have audit all ISA drivers and made sure none use ->cmnd in a DMA
Operation. Same audit was done by Andi Kleen.
(*)fixed-length here means commands that their size can be determined
by their opcode and the CDB does not carry a length specifier, (unlike
the VARIABLE_LENGTH_CMD(0x7f) command). This is actually not exactly
true and the SCSI standard also defines extended commands and
vendor specific commands that can be bigger than 16 bytes. The kernel
will support these using the same infrastructure used for VARLEN CDB's.
So in effect MAX_COMMAND_SIZE means the maximum size command
scsi-ml supports without specifying a cmd_len by ULD's
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This is needed by things like USB storage that want to set up static
commands for later use at start of day.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
LLDs need to copies data between the SG table in struct scsi_cmnd and
liner buffer. So they use the helper functions like
sg_copy_from_buffer(scsi_sglist(sc), scsi_sg_count(sc), buf, buflen)
sg_copy_to_buffer(scsi_sglist(sc), scsi_sg_count(sc), buf, buflen)
This patch just adds wrapper functions:
scsi_sg_copy_from_buffer(sc, buf, buflen)
scsi_sg_copy_to_buffer(sc, buf, buflen)
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
At the block level bidi request uses req->next_rq pointer for a second
bidi_read request.
At Scsi-midlayer a second scsi_data_buffer structure is used for the
bidi_read part. This bidi scsi_data_buffer is put on
request->next_rq->special. Struct scsi_cmnd is not changed.
- Define scsi_bidi_cmnd() to return true if it is a bidi request and a
second sgtable was allocated.
- Define scsi_in()/scsi_out() to return the in or out scsi_data_buffer
from this command This API is to isolate users from the mechanics of
bidi.
- Define scsi_end_bidi_request() to do what scsi_end_request() does but
for a bidi request. This is necessary because bidi commands are a bit
tricky here. (See comments in body)
- scsi_release_buffers() will also release the bidi_read scsi_data_buffer
- scsi_io_completion() on bidi commands will now call
scsi_end_bidi_request() and return.
- The previous work done in scsi_init_io() is now done in a new
scsi_init_sgtable() (which is 99% identical to old scsi_init_io())
The new scsi_init_io() will call the above twice if needed also for
the bidi_read command. Only at this point is a command bidi.
- In scsi_error.c at scsi_eh_prep/restore_cmnd() make sure bidi-lld is not
confused by a get-sense command that looks like bidi. This is done
by puting NULL at request->next_rq, and restoring.
[jejb: update to sg_table and resolve conflicts
also update to blk-end-request and resolve conflicts]
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
In preparation for bidi we abstract all IO members of scsi_cmnd,
that will need to duplicate, into a substructure.
- Group all IO members of scsi_cmnd into a scsi_data_buffer
structure.
- Adjust accessors to new members.
- scsi_{alloc,free}_sgtable receive a scsi_data_buffer instead of
scsi_cmnd. And work on it.
- Adjust scsi_init_io() and scsi_release_buffers() for above
change.
- Fix other parts of scsi_lib/scsi.c to members migration. Use
accessors where appropriate.
- fix Documentation about scsi_cmnd in scsi_host.h
- scsi_error.c
* Changed needed members of struct scsi_eh_save.
* Careful considerations in scsi_eh_prep/restore_cmnd.
- sd.c and sr.c
* sd and sr would adjust IO size to align on device's block
size so code needs to change once we move to scsi_data_buff
implementation.
* Convert code to use scsi_for_each_sg
* Use data accessors where appropriate.
- tgt: convert libsrp to use scsi_data_buffer
- isd200: This driver still bangs on scsi_cmnd IO members,
so need changing
[jejb: rebased on top of sg_table patches fixed up conflicts
and used the synergy to eliminate use_sg and sg_count]
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
If we export scsi_init_io()/scsi_release_buffers() instead of
scsi_{alloc,free}_sgtable() from scsi_lib than tgt code is much more
insulated from scsi_lib changes. As a bonus it will also gain bidi
capability when it comes.
[jejb: rebase on to sg_table and fix up rejections]
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Acked-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Also change scsi_alloc_sgtable() to just return 0/failure, since it
maps to the command passed in. ->request_buffer is now no longer needed,
once drivers are adapted to use scsi_sglist() it can be killed.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
This removes static array sense_buffer in scsi_cmnd and uses
dynamically allocated sense_buffer (with GFP_DMA).
The reason for doing this is that some architectures need cacheline
aligned buffer for DMA:
http://lkml.org/lkml/2007/11/19/2
The problems are that scsi_eh_prep_cmnd puts scsi_cmnd::sense_buffer
to sglist and some LLDs directly DMA to scsi_cmnd::sense_buffer. It's
necessary to DMA to scsi_cmnd::sense_buffer safely. This patch solves
these issues.
__scsi_get_command allocates sense_buffer via kmem_cache_alloc and
attaches it to a scsi_cmnd so everything just work as before.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This reverts commit ac40532ef0, which gets
us back the original cleanup of 6f5391c283.
It turns out that the bug that was triggered by that commit was
apparently not actually triggered by that commit at all, and just the
testing conditions had changed enough to make it appear to be due to it.
The real problem seems to have been found by Peter Osterlund:
"pktcdvd sets it [block device size] when opening the /dev/pktcdvd
device, but when the drive is later opened as /dev/scd0, there is
nothing that sets it back. (Btw, 40944 is possible if the disk is a
CDRW that was formatted with "cdrwtool -m 10236".)
The problem is that pktcdvd opens the cd device in non-blocking mode
when pktsetup is run, and doesn't close it again until pktsetup -d is
run. The effect is that if you meanwhile open the cd device,
blkdev.c:do_open() doesn't call bd_set_size() because
bdev->bd_openers is non-zero."
In particular, to repeat the bug (regardless of whether commit
6f5391c283 is applied or not):
" 1. Start with an empty drive.
2. pktsetup 0 /dev/scd0
3. Insert a CD containing an isofs filesystem.
4. mount /dev/pktcdvd/0 /mnt/tmp
5. umount /mnt/tmp
6. Press the eject button.
7. Insert a DVD containing a non-writable filesystem.
8. mount /dev/scd0 /mnt/tmp
9. find /mnt/tmp -type f -print0 | xargs -0 sha1sum >/dev/null
10. If the DVD contains data beyond the physical size of a CD, you
get I/O errors in the terminal, and dmesg reports lots of
"attempt to access beyond end of device" errors."
which in turn is because the nested open after the media change won't
cause the size to be set properly (because the original open still holds
the block device, and we only do the bd_set_size() when we don't have
other people holding the device open).
The proper fix for that is probably to just do something like
bdev->bd_inode->i_size = (loff_t)get_capacity(disk)<<9;
in fs/block_dev.c:do_open() even for the cases where we're not the
original opener (but *not* call bd_set_size(), since that will also
change the block size of the device).
Cc: Peter Osterlund <petero2@telia.com>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Matthew Wilcox <matthew@wil.cx>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This reverts commit 6f5391c283 ("[SCSI]
Get rid of scsi_cmnd->done") that was supposed to be a cleanup commit,
but apparently it causes regressions:
Bug 9370 - v2.6.24-rc2-409-g9418d5d: attempt to access beyond end of device
http://bugzilla.kernel.org/show_bug.cgi?id=9370
this patch should be reintroduced in a more split-up form to make
testing of it easier.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Acked-by: Matthew Wilcox <matthew@wil.cx>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is what enables large commands. If we need to allocate an
sgtable that doesn't fit in a single page, allocate several
SCSI_MAX_SG_SEGMENTS sized tables and chain them together.
SCSI defaults to large chained sg tables, if the arch supports it.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Just pass in the command, no point in passing in the scatterlist
and scatterlist pool index seperately.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
This converts the SCSI mid layer to using the sg helpers for looking up
sg elements, instead of doing it manually.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
The ULD ->done callback moves into the scsi_driver. By moving the call
to scsi_io_completion() from scsi_blk_pc_done() to scsi_finish_command(),
we can eliminate the latter entirely. By returning 'good_bytes' from
the ->done callback (rather than invoking scsi_io_completion()), we can
stop exporting scsi_io_completion().
Also move the prototypes from sd.h to sd.c as they're all internal anyway.
Rename sd_rw_intr to sd_done and rw_intr to sr_done.
Inspired-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The pid field is a duplicate of the serial_number field and has been
scheduled for removal for a long time. A few drivers were still using
it, so just change them to use serial_number instead.
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This adds a set of accessors for the scsi data buffer. This is in
preparation for chaining sg lists and bidirectional requests (and
possibly, the mid-layer dma mapping).
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
scsi tgt breaks up a command into multple scatterlists
if we cannot fit all the data in one. This was because
the block rq helpers did not support large requests and
because we can get a command of any old size so it is
hard to preallocate pages for scatterlist large enough
(we cannot really preallocate pages with the bio map
user path). In 2.6.20, we added large request support to
the block layer helper, blk_rq_map_user. And at LSF,
we talked about increasing SCSI_MAX_PHYS_SEGMENTS for
scsi tgt if we want to support really really :) large
(greater than 256 * PAGE_SIZE in the worst mapping case)
requests.
The only target currently implemented does not even support
the multiple scatterlists stuff and only supports smaller
requests, so this patch just coverts scsi tgt to use
blk_rq_map_user.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch contains the needed changes to the scsi-ml for the target
mode support.
Note, per the last review we moved almost all the fields we added
to the scsi_cmnd to our internal data structure which we are going
to try and kill off when we can replace it with support from other
parts of the kernel.
The one field we left on was the offset variable. This is needed to handle
the case where the target gets request that is so large that it cannot
execute it in one dma operation. So max_secotors or a segment limit may
limit the size of the transfer. In this case our tgt core code will
break up the command into managable transfers and send them to the
LLD one at a time. The offset is then used to tell the LLD where in
the command we are at. Is there another field on the scsi_cmd for
that?
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
These aren't used anymore since the field in scsi_cmnd where it was
stored has been removed.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Currently struct scsi_cmnd has various fields that are used to backup
original data after the corresponding fields have been overridden for
EH commands. This means drivers can easily get at it and misuse it.
Due to the old_ naming this doesn't happen for most of them, but two
that have different names have been used wrong a lot (see previous
patch). Another downside is that they unessecarily bloat the scsi_cmnd
size.
This patch moves them onstack in scsi_send_eh_cmnd to fix those two
issues aswell as allowing future EH fixes like moving the EH command
submissions to use SG lists like everything else.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch simplifies "good_bytes" computation in sd_rw_intr().
sd: "good_bytes" computation is always done in terms of the resolution
of the device's medium, since after that it is the number of good bytes
we pass around and other layers/contexts (as opposed ot sd) can translate
that to their own resolution (block layer:512). It also makes
scsi_io_completion() processing more straightforward, eliminating the
3rd argument to the function.
It also fixes a couple of bugs like not checking return value,
using "break" instead of "return;", etc.
I've been running with this patch for some time now on a
test (do-it-all) system.
Signed-off-by: Luben Tuikov <ltuikov@yahoo.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
With Achim patch the last user (gdth) is switched away from scsi_request
so we an kill it now. Also disables some code in i2o_scsi that was
broken since the sg driver stopped using scsi_requests.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Introduce scsi_req_abort_cmd(struct scsi_cmnd *).
This function requests that SCSI Core start recovery for the
command by deleting the timer and adding the command to the eh
queue. It can be called by either LLDDs or SCSI Core. LLDDs who
implement their own error recovery MAY ignore the timeout event if
they generated scsi_req_abort_cmd.
First post:
http://marc.theaimsgroup.com/?l=linux-scsi&m=113833937421677&w=2
Signed-off-by: Luben Tuikov <ltuikov@yahoo.com>
Signed-off-by: Tejun Heo <htejun@gmail.com>
The current dc395x driver uses PIO to transfer up to 4 bytes which do not
get transferred by DMA (under unclear circumstances). For this the driver
uses page_address() which is broken on highmem. Apart from this the
actual calculation of the virtual address is wrong (even without highmem).
So, e.g., for reading it reads bytes from the driver to a wrong address
and returns wrong data, I guess, for writing it would just output random
data to the device.
The proper fix, as suggested by many, is to dynamically map data using
kmap_atomic(page, KM_BIO_SRC_IRQ) / kunmap_atomic(virt). The reason why it
has not been done until now, although I've done some preliminary patches
more than a year ago was that nobody interested in fixing this problem was
able to reliably reproduce it. Now it changed - with the help from
Sebastian Frei (CC'ed) I was able to trigger the PIO path. Thus, I was
also able to test and debug it.
There are 4 cases when PIO is used in dc395x - data-in / -out with and
without scatter-gather. I was able to reproduce and test only data-in with
and without SG. So, the data-out path is still untested, but it is also
somewhat simpler than the data-in. Fredrik Roubert (also CC'ed) also had
PIO triggering on his system, and in his case it was data-out without SG.
It would be great if he could test the attached patch on his system, but
even if he cannot, I would still request to apply the patch and just wait
if anybody cries...
Implementation: I put 2 new functions in scsi_lib.c and their declarations
in scsi_cmnd.h. I exported them without _GPL, although, I don't feel
strongly about that - not many drivers are likely to use them. But there
is at least one more - I want to use them in tmscsim.c. Whether these are
the right files for the functions and their declarations - not sure
either. Actually, they are not scsi-specific, so, might go somewhere
around other scattergather magic? They are not platform specific either,
and most SG functions are defined under arch/*/... As these issues were
discussed previously there were some more routines suggested to manipulate
scattergather buffers, I think, some of them were needed around
crypto code... So, might be a common place reasonable, like
lib/scattergather.c? I am open here.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
LLDDs should never see REQ_BLOCK_PC requests, we can handle them just
fine in the core code. There is a small behaviour change in that some
check in sr's rw_intr are bypassed, but I consider the old behaviour
a bug.
Mike found this cleanup opportunity and provdided early patches, so all
the credit goes to him, even if I redid the patches from scratch beause
that was easier than forward-porting the old patches.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This follows on from Jens' patch and consolidates all of the ULD
separate handlers for REQ_BLOCK_PC into a single call which has his
fix for our direction bug.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
I recently picked up my older work to remove unnecessary #includes of
sched.h, starting from a patch by Dave Jones to not include sched.h
from module.h. This reduces the number of indirect includes of sched.h
by ~300. Another ~400 pointless direct includes can be removed after
this disentangling (patch to follow later).
However, quite a few indirect includes need to be fixed up for this.
In order to feed the patches through -mm with as little disturbance as
possible, I've split out the fixes I accumulated up to now (complete for
i386 and x86_64, more archs to follow later) and post them before the real
patch. This way this large part of the patch is kept simple with only
adding #includes, and all hunks are independent of each other. So if any
hunk rejects or gets in the way of other patches, just drop it. My scripts
will pick it up again in the next round.
Signed-off-by: Tim Schmielau <tim@physik3.uni-rostock.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
There are certain rogue devices (and the aic7xxx driver) that return
BUSY or QUEUE_FULL forever. This code will apply a global timeout (of
the total number of retries times the per command timer) to a given
command. If it is exceeded, the command is completed regardless of its
state.
The patch also removes the unused field in the command: timeout and
timeout_total.
This solves the problem of detecting an endless loop in the mid-layer
because of BUSY/QUEUE_FULL bouncing, but will not recover the device.
In the aic7xxx case, the driver can be recovered by sending a bus reset,
so possibly this should be tied into the error handler?
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
We never look at it except for the old megaraid driver that abuses it
for sending internal commands. That usage can be fixed easily because
those internal commands are single-threaded by a mutex and we can easily
use a completion there.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
it's never set to anything, and just three broken drivers are looking
at it and doing odd things.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
scsi_cmnd->serial_number_at_timeout doesn't serve any purpose
anymore. All serial_number == serial_number_at_timeout tests
are always true in abort callbacks. Kill the field. Also, as
->pid always equals ->serial_number and ->serial_number
doesn't have any special meaning anymore, update comments
above ->serial_number accordingly. Once we remove all uses of
this field from all lldd's, this field should go.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Mark Rustad
Martin K. Petersen
Moger, Babu
Tejun Heo
James Bottomley
Jens Axboe
Alexander Beregalov
Boaz Harrosh
FUJITA Tomonori
Linus Torvalds
Ingo Molnar
Matthew Wilcox
Mike Christie
Christoph Hellwig
Luben Tuikov
Jeff Garzik
Guennadi Liakhovetski
James Bottomley
James Bottomley
Tim Schmielau
Al Viro
