cpufreq_quick_get() allows cpufreq drivers to over-ride cpu_khz
that is otherwise reported in x86 /proc/cpuinfo "cpu MHz".
There are four problems with this scheme,
any of them is sufficient justification to delete it.
1. Depending on which cpufreq driver is loaded, the behavior
of this field is different.
2. Distros complain that they have to explain to users
why and how this field changes. Distros have requested a constant.
3. The two major providers of this information, acpi_cpufreq
and intel_pstate, both "get it wrong" in different ways.
acpi_cpufreq lies to the user by telling them that
they are running at whatever frequency was last
requested by software.
intel_pstate lies to the user by telling them that
they are running at the average frequency computed
over an undefined measurement. But an average computed
over an undefined interval, is itself, undefined...
4. On modern processors, user space utilities, such as
turbostat(1), are more accurate and more precise, while
supporing concurrent measurement over arbitrary intervals.
Users who have been consulting /proc/cpuinfo to
track changing CPU frequency will be dissapointed that
it no longer wiggles -- perhaps being unaware of the
limitations of the information they have been consuming.
Yes, they can change their scripts to look in sysfs
cpufreq/scaling_cur_frequency. Here they will find the same
data of dubious quality here removed from /proc/cpuinfo.
The value in sysfs will be addressed in a subsequent patch
to address issues 1-3, above.
Issue 4 will remain -- users that really care about
accurate frequency information should not be using either
proc or sysfs kernel interfaces.
They should be using using turbostat(8), or a similar
purpose-built analysis tool.
Signed-off-by: Len Brown <len.brown@intel.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Remove the wp_works_ok member of struct cpuinfo_x86. It's an
optimization back from Linux v0.99 times where we had no fixup support
yet and did the CR0.WP test via special code in the page fault handler.
The < 0 test was an optimization to not do the special casing for each
NULL ptr access violation but just for the first one doing the WP test.
Today it serves no real purpose as the test no longer needs special code
in the page fault handler and the only call side -- mem_init() -- calls
it just once, anyway. However, Xen pre-initializes it to 1, to skip the
test.
Doing the test again for Xen should be no issue at all, as even the
commit introducing skipping the test (commit d560bc6157 ("x86, xen:
Suppress WP test on Xen")) mentioned it being ban aid only. And, in
fact, testing the patch on Xen showed nothing breaks.
The pre-fixup times are long gone and with the removal of the fallback
handling code in commit a5c2a893db ("x86, 386 removal: Remove
CONFIG_X86_WP_WORKS_OK") the kernel requires a working CR0.WP anyway.
So just get rid of the "optimization" and do the test unconditionally.
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Acked-by: Borislav Petkov <bp@alien8.de>
Cc: Jesper Nilsson <jesper.nilsson@axis.com>
Cc: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Cc: Arnd Hannemann <hannemann@nets.rwth-aachen.de>
Cc: Mikael Starvik <starvik@axis.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: "David S. Miller" <davem@davemloft.net>
Link: http://lkml.kernel.org/r/1486933932-585-3-git-send-email-minipli@googlemail.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The former duplicate the functionalities of the latter but are
neither documented nor arch-independent.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Benoit Cousson <bcousson@baylibre.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Jean Delvare <jdelvare@suse.de>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Oleg Drokin <oleg.drokin@intel.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Viresh Kumar <viresh.kumar@linaro.org>
Link: http://lkml.kernel.org/r/1432645896-12588-9-git-send-email-bgolaszewski@baylibre.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Dump the flags which denote we have detected and/or have applied bug
workarounds to the CPU we're executing on, in a similar manner to the
feature flags.
The advantage is that those are not accumulating over time like the CPU
features.
Signed-off-by: Borislav Petkov <bp@suse.de>
Link: http://lkml.kernel.org/r/1403609105-8332-2-git-send-email-bp@alien8.de
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Currently show_cpuinfo_core() displays cpu core information only if
the number of threads per a whole cores is 2 or larger.
However, this condition doesn't care about the number of
sockets. For example, this condition doesn't hold on systems
with two logical cpus consisting of two sockets and a single
core on each socket - yet the topology information would be
interesting to see in that case as well.
I don't know whether or not there are processors in real world
by which such configurations are possible, but at least on
vitual machine environments, such configuration can occur,
typically when no explicit SMP information is provided in
advance.
For example, on qemu/KVM, SMP information is specified via -smp
command-line option, more specifically, its syntax is:
-smp n[,cores=cores][,threads=threads][,sockets=sockets][,maxcpus=maxcpus]
If this is not specified, qemu tells configuration with
n-sockets, 1-core and 1-thread to the guest machine, on which
guest, MP information is not displayed in /proc/cpuinfo.
I saw this situation on VMWare guest environment, too.
To fix this issue, this patch simply removes the condition
because this information is useful even if there's only 1
thread.
Signed-off-by: HATAYAMA Daisuke <d.hatayama@jp.fujitsu.com>
Cc: Vivek Goyal <vgoyal@redhat.com>
Cc: H. Peter Anvin <hpa@linux.intel.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/5277D644.4090707@jp.fujitsu.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Reimplement FPU detection code in C and drop old, not-so-recommended
detection method in asm. Move all the relevant stuff into i387.c where
it conceptually belongs. Finally drop cpuinfo_x86.hard_math.
[ hpa: huge thanks to Borislav for taking my original concept patch
and productizing it ]
[ Boris, note to self: do not use static_cpu_has before alternatives! ]
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Link: http://lkml.kernel.org/r/1367244262-29511-2-git-send-email-bp@alien8.de
Link: http://lkml.kernel.org/r/1365436666-9837-2-git-send-email-bp@alien8.de
Signed-off-by: Borislav Petkov <bp@suse.de>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Remove 32-bit x86 a cmdline param "no-hlt",
and the cpuinfo_x86.hlt_works_ok that it sets.
If a user wants to avoid HLT, then "idle=poll"
is much more useful, as it avoids invocation of HLT
in idle, while "no-hlt" failed to do so.
Indeed, hlt_works_ok was consulted in only 3 places.
First, in /proc/cpuinfo where "hlt_bug yes"
would be printed if and only if the user booted
the system with "no-hlt" -- as there was no other code
to set that flag.
Second, check_hlt() would not invoke halt() if "no-hlt"
were on the cmdline.
Third, it was consulted in stop_this_cpu(), which is invoked
by native_machine_halt()/reboot_interrupt()/smp_stop_nmi_callback() --
all cases where the machine is being shutdown/reset.
The flag was not consulted in the more frequently invoked
play_dead()/hlt_play_dead() used in processor offline and suspend.
Since Linux-3.0 there has been a run-time notice upon "no-hlt" invocations
indicating that it would be removed in 2012.
Signed-off-by: Len Brown <len.brown@intel.com>
Cc: x86@kernel.org
Remove support for FPU error reporting via IRQ 13, as opposed to
exception 16 (#MF). One last remnant of i386 gone.
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Cc: Alan Cox <alan@linux.intel.com>
Several fields in struct cpuinfo_x86 were not defined for the
!SMP case, likely to save space. However, those fields still
have some meaning for UP, and keeping them allows some #ifdef
removal from other files. The additional size of the UP kernel
from this change is not significant enough to worry about
keeping up the distinction:
text data bss dec hex filename
4737168 506459 972040 6215667 5ed7f3 vmlinux.o.before
4737444 506459 972040 6215943 5ed907 vmlinux.o.after
for a difference of 276 bytes for an example UP config.
If someone wants those 276 bytes back badly then it should
be implemented in a cleaner way.
Signed-off-by: Kevin Winchester <kjwinchester@gmail.com>
Cc: Steffen Persvold <sp@numascale.com>
Link: http://lkml.kernel.org/r/1324428742-12498-1-git-send-email-kjwinchester@gmail.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
506ed6b53e ("x86, intel: Output microcode revision in /proc/cpuinfo")
added microcode revision format to /proc/cpuinfo and the MCE handler in
decimal format but both AMD and Intel patch levels are handled as hex
numbers. Fix it.
Acked-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
I got a request to make it easier to determine the microcode
update level on Intel CPUs. This patch adds a new "microcode"
field to /proc/cpuinfo.
The microcode level is also outputed on fatal machine checks
together with the other CPUID model information.
I removed the respective code from the microcode update driver,
it just reads the field from cpu_data. Also when the microcode
is updated it fills in the new values too.
I had to add a memory barrier to native_cpuid to prevent it
being optimized away when the result is not used.
This turns out to clean up further code which already got this
information manually. This is done in followon patches.
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Acked-by: H. Peter Anvin <hpa@zytor.com>
Link: http://lkml.kernel.org/r/1318466795-7393-1-git-send-email-andi@firstfloor.org
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* 'x86-cpu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (22 commits)
x86: Fix code patching for paravirt-alternatives on 486
x86, msr: change msr-reg.o to obj-y, and export its symbols
x86: Use hard_smp_processor_id() to get apic id for AMD K8 cpus
x86, sched: Workaround broken sched domain creation for AMD Magny-Cours
x86, mcheck: Use correct cpumask for shared bank4
x86, cacheinfo: Fixup L3 cache information for AMD multi-node processors
x86: Fix CPU llc_shared_map information for AMD Magny-Cours
x86, msr: Fix msr-reg.S compilation with gas 2.16.1, on 32-bit too
x86: Move kernel_fpu_using to irq_fpu_usable in asm/i387.h
x86, msr: fix msr-reg.S compilation with gas 2.16.1
x86, msr: Export the register-setting MSR functions via /dev/*/msr
x86, msr: Create _on_cpu helpers for {rw,wr}msr_safe_regs()
x86, msr: Have the _safe MSR functions return -EIO, not -EFAULT
x86, msr: CFI annotations, cleanups for msr-reg.S
x86, asm: Make _ASM_EXTABLE() usable from assembly code
x86, asm: Add 32-bit versions of the combined CFI macros
x86, AMD: Disable wrongly set X86_FEATURE_LAHF_LM CPUID bit
x86, msr: Rewrite AMD rd/wrmsr variants
x86, msr: Add rd/wrmsr interfaces with preset registers
x86: add specific support for Intel Atom architecture
...
No code changes except printk levels (although some of the K6
mtrr code might be clearer if there were a few as would
splitting out some of the intel cache code).
Signed-off-by: Alan Cox <alan@linux.intel.com>
LKML-Reference: <new-submission>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
32 bits can also access x86_cache_alignment, x86_phys_bits and
x86_virt_bits, make them available to user space just as on 64 bits.
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
LKML-Reference: <1244921390.11733.30.camel@ht.satnam>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Commit 7ad728f981
(cpumask: x86: convert cpu_sibling_map/cpu_core_map to cpumask_var_t)
changed the output of /proc/cpuinfo for siblings:
Example on an AMD Phenom:
physical id : 0
siblings : 1
core id : 3
cpu cores : 4
Before that commit it was:
physical id : 0
siblings : 4
core id : 3
cpu cores : 4
Instead of cpu_core_mask it now uses cpu_sibling_mask to count siblings.
This is due to the following hunk of above commit:
| --- a/arch/x86/kernel/cpu/proc.c
| +++ b/arch/x86/kernel/cpu/proc.c
| @@ -14,7 +14,7 @@ static void show_cpuinfo_core(struct seq_file *m, struct cpuinf
| if (c->x86_max_cores * smp_num_siblings > 1) {
| seq_printf(m, "physical id\t: %d\n", c->phys_proc_id);
| seq_printf(m, "siblings\t: %d\n",
| - cpus_weight(per_cpu(cpu_core_map, cpu)));
| + cpumask_weight(cpu_sibling_mask(cpu)));
| seq_printf(m, "core id\t\t: %d\n", c->cpu_core_id);
| seq_printf(m, "cpu cores\t: %d\n", c->booted_cores);
| seq_printf(m, "apicid\t\t: %d\n", c->apicid);
This was a mistake, because the impact line shows that this side-effect
was not anticipated:
Impact: reduce per-cpu size for CONFIG_CPUMASK_OFFSTACK=y
So revert the respective hunk to restore the old behavior.
[ Impact: fix sibling-info regression in /proc/cpuinfo ]
Signed-off-by: Andreas Herrmann <andreas.herrmann3@amd.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
LKML-Reference: <20090504182859.GA29045@alberich.amd.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: reduce per-cpu size for CONFIG_CPUMASK_OFFSTACK=y
In most places it's cleaner to use the accessors cpu_sibling_mask()
and cpu_core_mask() wrappers which already exist.
I couldn't avoid cleaning up the access in oprofile, either.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Impact: unification
show_cpuinfo_core is identical for 32 and 64 bit and can be unified,
and CONFIG_X86_HT inherently depends on CONFIG_X86_SMP.
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Impact: fix missing CPUs in /proc/cpuinfo after CPU hotunplug/hotreplug
In my test, I found that if a cpu has been offline,
the next cpus may not be shown in the /proc/cpuinfo.
if one read() cannot consume the whole /proc/cpuinfo,
c_start() will be called again in the next read() calls.
And *pos has been increased by 1 by the caller(seq_read()).
if this time the cpu#*pos is offline, c_start() will return
NULL, and the next cpus can not be shown.
this fix use next_cpu_nr(*pos - 1, cpu_online_map) to
search the next unshown cpu.
the most easy way to reproduce this bug:
1) offline cpu#1 (cpu#0 is online)
2) dd ibs=2 if=/proc/cpuinfo
the result is that only cpu#0 is shown.
cpu#2 and cpu#3 .... cannot be shown in /proc/cpuinfo
it's bug.
Signed-off-by: Lai Jiangshan <laijs@cn.fujitsu.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* Use nr_cpu_ids instead of NR_CPUS to limit traversal of cpu online map.
Signed-off-by: Mike Travis <travis@sgi.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
None of these files use any of the functionality promised by
asm/semaphore.h. It's possible that they rely on it dragging in some
unrelated header file, but I can't build all these files, so we'll have
fix any build failures as they come up.
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
store initial_apicid from early identify. it is could be different from
phys_proc_id later.
also print it out in /proc/cpuinfo.
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Change /proc/cpuinfo on 32-bit, it will look like on 64-bit.
'power management' line is added and power management information
will be printed at the line.
Signed-off-by: Hiroshi Shimamoto <h-shimamoto@ct.jp.nec.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Move the CPU feature string names to a separate file (common to 32
and 64 bits); additionally, make <asm/cpufeature.h> includable by host
code in preparation for including the CPU feature strings in the boot
code.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Fix regressions introduced with 92cb7612ae.
It can happen that cpuinfo is displayed for CPUs that are not online or
even worse for CPUs not present at all. As an example, following was
shown for a "second" CPU of a single core K8 variant:
processor : 0
vendor_id : unknown
cpu family : 0
model : 0
model name : unknown
stepping : 0
cache size : 0 KB
fpu : yes
fpu_exception : yes
cpuid level : 0
wp : yes
flags :
bogomips : 0.00
clflush size : 0
cache_alignment : 0
address sizes : 0 bits physical, 0 bits virtual
power management:
Signed-off-by: Andreas Herrmann <andreas.herrmann3@amd.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Additional CPUID strings (sse4_1, sse4_2, sse5, skinit, wdt); fix the
positioning of the AMD ecx strings (cr8_legacy was duplicated under
two different names, so the alignment of all the other strings were
off by one.)
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
cpu_data is currently an array defined using NR_CPUS. This means that
we overallocate since we will rarely really use maximum configured cpus.
When NR_CPU count is raised to 4096 the size of cpu_data becomes
3,145,728 bytes.
These changes were adopted from the sparc64 (and ia64) code. An
additional field was added to cpuinfo_x86 to be a non-ambiguous cpu
index. This corresponds to the index into a cpumask_t as well as the
per_cpu index. It's used in various places like show_cpuinfo().
cpu_data is defined to be the boot_cpu_data structure for the NON-SMP
case.
Signed-off-by: Mike Travis <travis@sgi.com>
Acked-by: Christoph Lameter <clameter@sgi.com>
Cc: Andi Kleen <ak@suse.de>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Cc: Dmitry Torokhov <dtor@mail.ru>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Cc: Mark M. Hoffman <mhoffman@lightlink.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This is from an earlier message from 'Christoph Lameter':
cpu_core_map is currently an array defined using NR_CPUS. This means that
we overallocate since we will rarely really use maximum configured cpu.
If we put the cpu_core_map into the per cpu area then it will be allocated
for each processor as it comes online.
This means that the core map cannot be accessed until the per cpu area
has been allocated. Xen does a weird thing here looping over all processors
and zeroing the masks that are not yet allocated and that will be zeroed
when they are allocated. I commented the code out.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Mike Travis <travis@sgi.com>
Cc: Andi Kleen <ak@suse.de>
Cc: Christoph Lameter <clameter@sgi.com>
Cc: "Siddha, Suresh B" <suresh.b.siddha@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Len Brown
Mathias Krause
Bartosz Golaszewski
Rasmus Villemoes
Borislav Petkov
HATAYAMA Daisuke
H. Peter Anvin
H. Peter Anvin
Michael Wang
Kevin Winchester
Borislav Petkov
Andi Kleen
Linus Torvalds
Alan Cox
Jaswinder Singh Rajput
Andreas Herrmann
Rusty Russell
Jaswinder Singh Rajput
Lai Jiangshan
Mike Travis
Matthew Wilcox
Yinghai Lu
Hiroshi Shimamoto
Jan Engelhardt
Thomas Gleixner