Files removed in 'net-next' had their license header updated
in 'net'. We take the remove from 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 9a03c3d398 ("thunderbolt: Fix a couple right shifting to zero
bugs") revealed an issue that was previously hidden because we never
actually compared received XDomain message sequence numbers properly.
The idea with these sequence numbers is that the responding host uses
the same sequence number that was in the request packet which we can
then check at the requesting host.
However, testing against macOS it looks like it does not follow this but
instead uses some other logic. Windows driver on the other hand handles
it the same way than Linux.
In order to be able to talk to macOS again, fix this so that we drop the
whole sequence number check. This effectively works exactly the same
than it worked before the aforementioned commit. This also follows the
logic the original P2P networking code used.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The problematic code looks like this:
res_seq = res_hdr->xd_hdr.length_sn & TB_XDOMAIN_SN_MASK;
res_seq >>= TB_XDOMAIN_SN_SHIFT;
TB_XDOMAIN_SN_SHIFT is 27, and right shifting a u8 27 bits is always
going to result in zero. The fix is to declare these variables as u32.
Fixes: d1ff70241a ("thunderbolt: Add support for XDomain discovery protocol")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 0day kbuild robot reports following crash:
BUG: unable to handle kernel NULL pointer dereference at 00000004
IP: tb_property_find+0xe/0x41
*pde = 00000000
Oops: 0000 [#1]
CPU: 0 PID: 1 Comm: swapper Not tainted 4.14.0-rc1-00741-ge69b6c0 #412
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.10.2-1 04/01/2014
task: 89c80000 task.stack: 89c7c000
EIP: tb_property_find+0xe/0x41
EFLAGS: 00210246 CPU: 0
EAX: 00000000 EBX: 7a368f47 ECX: 00000044 EDX: 7a368f47
ESI: 8851d340 EDI: 7a368f47 EBP: 89c7df0c ESP: 89c7defc
DS: 007b ES: 007b FS: 0000 GS: 0000 SS: 0068
CR0: 80050033 CR2: 00000004 CR3: 027a2000 CR4: 00000690
Call Trace:
tb_register_property_dir+0x49/0xb9
? cdc_mbim_driver_init+0x1b/0x1b
tbnet_init+0x77/0x9f
? cdc_mbim_driver_init+0x1b/0x1b
do_one_initcall+0x7e/0x145
? parse_args+0x10c/0x1b3
? kernel_init_freeable+0xbe/0x159
kernel_init_freeable+0xd1/0x159
? rest_init+0x110/0x110
kernel_init+0xd/0xd0
ret_from_fork+0x19/0x30
The reason is that both Thunderbolt bus and thunderbolt-net are build
into the kernel image, and the latter is linked first because
drivers/net comes before drivers/thunderbolt. Since both use
module_init() thunderbolt-net ends up calling Thunderbolt bus functions
too early triggering the above crash.
Fix this by moving Thunderbolt bus initialization to happen earlier to
make sure all the data structures are ready when Thunderbolt service
drivers are initialized. To be on the safe side also add a check for
properly initialized xdomain_property_dir to tb_register_property_dir().
Reported-by: kernel test robot <fengguang.wu@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Thunderbolt services should not care which HopID (ring) they use for
sending and receiving packets over the high-speed DMA path, so make
tb_ring_alloc_rx() and tb_ring_alloc_tx() accept negative HopID. This
means that the NHI will allocate next available HopID for the caller
automatically.
These HopIDs will be allocated from the range which is not reserved for
the Thunderbolt protocol (8 .. hop_count - 1).
The allocated HopID can be retrieved from ring->hop field after the ring
has been allocated successfully if needed.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Michael Jamet <michael.jamet@intel.com>
Reviewed-by: Yehezkel Bernat <yehezkel.bernat@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to support things like networking over Thunderbolt cable, there
needs to be a way to switch the ring to a mode where it can be polled
with the interrupt masked. We implement such mode so that the caller can
allocate a ring by passing pointer to a function that is then called
when an interrupt is triggered. Completed frames can be fetched using
tb_ring_poll() and the interrupt can be re-enabled when the caller is
finished with polling by using tb_ring_poll_complete().
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Michael Jamet <michael.jamet@intel.com>
Reviewed-by: Yehezkel Bernat <yehezkel.bernat@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is needed because ring polling functionality can be called from
atomic contexts when networking and other high-speed traffic is
transferred over a Thunderbolt cable.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Michael Jamet <michael.jamet@intel.com>
Reviewed-by: Yehezkel Bernat <yehezkel.bernat@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This makes it possible to enqueue frames also from atomic context which
is needed for example, when networking packets are sent over a
Thunderbolt cable.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Michael Jamet <michael.jamet@intel.com>
Reviewed-by: Yehezkel Bernat <yehezkel.bernat@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A Thunderbolt service driver might need to check if there was an error
with the descriptor when in frame mode. We also add two Rx specific
error flags RING_DESC_CRC_ERROR and RING_DESC_BUFFER_OVERRUN.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Michael Jamet <michael.jamet@intel.com>
Reviewed-by: Yehezkel Bernat <yehezkel.bernat@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These are used by Thunderbolt services to send and receive frames over
the high-speed DMA rings.
We also put the functions to tb_ namespace to make sure we do not
collide with others and add missing kernel-doc comments for the exported
functions.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Michael Jamet <michael.jamet@intel.com>
Reviewed-by: Yehezkel Bernat <yehezkel.bernat@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When high-speed DMA paths are used to transfer arbitrary data over a
Thunderbolt link, DMA rings should be in frame mode instead of raw mode.
The latter is used by the control channel (ring 0). In frame mode each
data frame can hold up to 4kB payload.
This patch modifies the DMA ring code to allow configuring a ring to be
in frame mode by passing a new flag (RING_FLAG_FRAME) to the ring when
it is allocated. In addition there might be need to enable end-to-end
(E2E) workaround for the ring to prevent losing Rx frames in certain
situations. We add another flag (RING_FLAG_E2E) that can be used for
this purpose.
This code is based on the work done by Amir Levy and Michael Jamet.
Signed-off-by: Michael Jamet <michael.jamet@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Yehezkel Bernat <yehezkel.bernat@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This will keep the interrupt delivery rate reasonable. The value used
here (128 us) is a recommendation from the hardware people.
This code is based on the work done by Amir Levy and Michael Jamet.
Signed-off-by: Michael Jamet <michael.jamet@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Yehezkel Bernat <yehezkel.bernat@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When two hosts are connected over a Thunderbolt cable, there is a
protocol they can use to communicate capabilities supported by the host.
The discovery protocol uses automatically configured control channel
(ring 0) and is build on top of request/response transactions using
special XDomain primitives provided by the Thunderbolt base protocol.
The capabilities consists of a root directory block of basic properties
used for identification of the host, and then there can be zero or more
directories each describing a Thunderbolt service and its capabilities.
Once both sides have discovered what is supported the two hosts can
setup high-speed DMA paths and transfer data to the other side using
whatever protocol was agreed based on the properties. The software
protocol used to communicate which DMA paths to enable is service
specific.
This patch adds support for the XDomain discovery protocol to the
Thunderbolt bus. We model each remote host connection as a Linux XDomain
device. For each Thunderbolt service found supported on the XDomain
device, we create Linux Thunderbolt service device which Thunderbolt
service drivers can then bind to based on the protocol identification
information retrieved from the property directory describing the
service.
This code is based on the work done by Amir Levy and Michael Jamet.
Signed-off-by: Michael Jamet <michael.jamet@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Yehezkel Bernat <yehezkel.bernat@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A Thunderbolt service might need to find the physical port from a link
the cable is connected to. For instance networking driver uses this
information to generate MAC address according the Apple ThunderboltIP
protocol.
Move this function to thunderbolt.h and rename it to
tb_phy_port_from_link() to reflect the fact that it does not take switch
as parameter.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Michael Jamet <michael.jamet@intel.com>
Reviewed-by: Yehezkel Bernat <yehezkel.bernat@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These are needed by Thunderbolt services so move them to thunderbolt.h
to make sure they are available outside of drivers/thunderbolt.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Michael Jamet <michael.jamet@intel.com>
Reviewed-by: Yehezkel Bernat <yehezkel.bernat@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These will be needed by Thunderbolt services when sending and receiving
XDomain control messages. While there change TB_CFG_PKG_PREPARE_TO_SLEEP
value to be decimal in order to be consistent with other members.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Michael Jamet <michael.jamet@intel.com>
Reviewed-by: Yehezkel Bernat <yehezkel.bernat@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Thunderbolt XDomain discovery protocol uses directories which contain
properties and other directories to exchange information about what
capabilities the remote host supports. This also includes identification
information like device ID and name.
This adds support for parsing and formatting these properties and
establishes an API drivers can use in addition to the core Thunderbolt
driver. This API is exposed in a new header: include/linux/thunderbolt.h.
This code is based on the work done by Amir Levy and Michael Jamet.
Signed-off-by: Michael Jamet <michael.jamet@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Yehezkel Bernat <yehezkel.bernat@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These messages are all 32-bit aligned and they should be packed without
the __packed attribute just fine. It also allows compiler to generate
better code on some architectures.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Michael Jamet <michael.jamet@intel.com>
Reviewed-by: Yehezkel Bernat <yehezkel.bernat@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We will be using these when communicating XDomain discovery protocol
over Thunderbolt link but they might be useful for other drivers as
well.
Make them available through byteorder/generic.h.
Suggested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Michael Jamet <michael.jamet@intel.com>
Reviewed-by: Yehezkel Bernat <yehezkel.bernat@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Update the ACPICA code in the kernel to upstream revision 20170728
including:
* Alias operator handling update (Bob Moore).
* Deferred resolution of reference package elements (Bob Moore).
* Support for the _DMA method in walk resources (Bob Moore).
* Tables handling update and support for deferred table
verification (Lv Zheng).
* Update of SMMU models for IORT (Robin Murphy).
* Compiler and disassembler updates (Alex James, Erik Schmauss,
Ganapatrao Kulkarni, James Morse).
* Tools updates (Erik Schmauss, Lv Zheng).
* Assorted minor fixes and cleanups (Bob Moore, Kees Cook,
Lv Zheng, Shao Ming).
- Rework the initialization of non-wakeup GPEs with method handlers
in order to address a boot crash on some systems with Thunderbolt
devices connected at boot time where we miss an early hotplug
event due to a delay in GPE enabling (Rafael Wysocki).
- Rework the handling of PCI bridges when setting up ACPI-based
device wakeup in order to avoid disabling wakeup for bridges
prematurely (Rafael Wysocki).
- Consolidate Apple DMI checks throughout the tree, add support for
Apple device properties to the device properties framework and
use these properties for the handling of I2C and SPI devices on
Apple systems (Lukas Wunner).
- Add support for _DMA to the ACPI-based device properties lookup
code and make it possible to use the information from there to
configure DMA regions on ARM64 systems (Lorenzo Pieralisi).
- Fix several issues in the APEI code, add support for exporting
the BERT error region over sysfs and update APEI MAINTAINERS
entry with reviewers information (Borislav Petkov, Dongjiu Geng,
Loc Ho, Punit Agrawal, Tony Luck, Yazen Ghannam).
- Fix a potential initialization ordering issue in the ACPI EC
driver and clean it up somewhat (Lv Zheng).
- Update the ACPI SPCR driver to extend the existing XGENE 8250
workaround in it to a new platform (m400) and to work around
an Xgene UART clock issue (Graeme Gregory).
- Add a new utility function to the ACPI core to support using
ACPI OEM ID / OEM Table ID / Revision for system identification
in blacklisting or similar and switch over the existing code
already using this information to this new interface (Toshi Kani).
- Fix an xpower PMIC issue related to GPADC reads that always return
0 without extra pin manipulations (Hans de Goede).
- Add statements to print debug messages in a couple of places in
the ACPI core for easier diagnostics (Rafael Wysocki).
- Clean up the ACPI processor driver slightly (Colin Ian King,
Hanjun Guo).
- Clean up the ACPI x86 boot code somewhat (Andy Shevchenko).
- Add a quirk for Dell OptiPlex 9020M to the ACPI backlight
driver (Alex Hung).
- Assorted fixes, cleanups and updates related to ACPI (Amitoj Kaur
Chawla, Bhumika Goyal, Frank Rowand, Jean Delvare, Punit Agrawal,
Ronald Tschalär, Sumeet Pawnikar).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=6Ke9
-----END PGP SIGNATURE-----
Merge tag 'acpi-4.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI updates from Rafael Wysocki:
"These include a usual ACPICA code update (this time to upstream
revision 20170728), a fix for a boot crash on some systems with
Thunderbolt devices connected at boot time, a rework of the handling
of PCI bridges when setting up device wakeup, new support for Apple
device properties, support for DMA configurations reported via ACPI on
ARM64, APEI-related updates, ACPI EC driver updates and assorted minor
modifications in several places.
Specifics:
- Update the ACPICA code in the kernel to upstream revision 20170728
including:
* Alias operator handling update (Bob Moore).
* Deferred resolution of reference package elements (Bob Moore).
* Support for the _DMA method in walk resources (Bob Moore).
* Tables handling update and support for deferred table
verification (Lv Zheng).
* Update of SMMU models for IORT (Robin Murphy).
* Compiler and disassembler updates (Alex James, Erik Schmauss,
Ganapatrao Kulkarni, James Morse).
* Tools updates (Erik Schmauss, Lv Zheng).
* Assorted minor fixes and cleanups (Bob Moore, Kees Cook, Lv
Zheng, Shao Ming).
- Rework the initialization of non-wakeup GPEs with method handlers
in order to address a boot crash on some systems with Thunderbolt
devices connected at boot time where we miss an early hotplug event
due to a delay in GPE enabling (Rafael Wysocki).
- Rework the handling of PCI bridges when setting up ACPI-based
device wakeup in order to avoid disabling wakeup for bridges
prematurely (Rafael Wysocki).
- Consolidate Apple DMI checks throughout the tree, add support for
Apple device properties to the device properties framework and use
these properties for the handling of I2C and SPI devices on Apple
systems (Lukas Wunner).
- Add support for _DMA to the ACPI-based device properties lookup
code and make it possible to use the information from there to
configure DMA regions on ARM64 systems (Lorenzo Pieralisi).
- Fix several issues in the APEI code, add support for exporting the
BERT error region over sysfs and update APEI MAINTAINERS entry with
reviewers information (Borislav Petkov, Dongjiu Geng, Loc Ho, Punit
Agrawal, Tony Luck, Yazen Ghannam).
- Fix a potential initialization ordering issue in the ACPI EC driver
and clean it up somewhat (Lv Zheng).
- Update the ACPI SPCR driver to extend the existing XGENE 8250
workaround in it to a new platform (m400) and to work around an
Xgene UART clock issue (Graeme Gregory).
- Add a new utility function to the ACPI core to support using ACPI
OEM ID / OEM Table ID / Revision for system identification in
blacklisting or similar and switch over the existing code already
using this information to this new interface (Toshi Kani).
- Fix an xpower PMIC issue related to GPADC reads that always return
0 without extra pin manipulations (Hans de Goede).
- Add statements to print debug messages in a couple of places in the
ACPI core for easier diagnostics (Rafael Wysocki).
- Clean up the ACPI processor driver slightly (Colin Ian King, Hanjun
Guo).
- Clean up the ACPI x86 boot code somewhat (Andy Shevchenko).
- Add a quirk for Dell OptiPlex 9020M to the ACPI backlight driver
(Alex Hung).
- Assorted fixes, cleanups and updates related to ACPI (Amitoj Kaur
Chawla, Bhumika Goyal, Frank Rowand, Jean Delvare, Punit Agrawal,
Ronald Tschalär, Sumeet Pawnikar)"
* tag 'acpi-4.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (75 commits)
ACPI / APEI: Suppress message if HEST not present
intel_pstate: convert to use acpi_match_platform_list()
ACPI / blacklist: add acpi_match_platform_list()
ACPI, APEI, EINJ: Subtract any matching Register Region from Trigger resources
ACPI: make device_attribute const
ACPI / sysfs: Extend ACPI sysfs to provide access to boot error region
ACPI: APEI: fix the wrong iteration of generic error status block
ACPI / processor: make function acpi_processor_check_duplicates() static
ACPI / EC: Clean up EC GPE mask flag
ACPI: EC: Fix possible issues related to EC initialization order
ACPI / PM: Add debug statements to acpi_pm_notify_handler()
ACPI: Add debug statements to acpi_global_event_handler()
ACPI / scan: Enable GPEs before scanning the namespace
ACPICA: Make it possible to enable runtime GPEs earlier
ACPICA: Dispatch active GPEs at init time
ACPI: SPCR: work around clock issue on xgene UART
ACPI: SPCR: extend XGENE 8250 workaround to m400
ACPI / LPSS: Don't abort ACPI scan on missing mem resource
mailbox: pcc: Drop uninformative output during boot
ACPI/IORT: Add IORT named component memory address limits
...
There is a mistake here where we accidentally use sizeof(TB_CFG_PKG_RESET)
instead of just TB_CFG_PKG_RESET. The size of an int is 4 so it's the
same as TB_CFG_PKG_NOTIFY_ACK.
Fixes: d7f781bfdb ("thunderbolt: Rework control channel to be more reliable")
Reported-by: Colin King <colin.king@canonical.com>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: stable <stable@vger.kernel.org> # 4.13
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If secure authentication of a devices fails, either because the device
already has another key uploaded, or there is some other error sending
challenge to the device, and the user only wants to approve the device
just once (without a new key being uploaded to the device) the current
implementation does not allow this because the key cannot be cleared
once set even if we allow it to be changed.
Make this scenario possible and allow clearing the key by writing
empty string to the key sysfs file.
Signed-off-by: Yehezkel Bernat <yehezkel.bernat@intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Non-root user may read the key back after root wrote it there.
This removes read access to everyone but root.
Signed-off-by: Yehezkel Bernat <yehezkel.bernat@intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The key size is tested by hex2bin() already (as '\0' isn't an hex digit)
Suggested-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Signed-off-by: Yehezkel Bernat <yehezkel.bernat@intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here are two patches for 4.13-rc5.
One is a fix for a reported thunderbolt issue, and the other a fix for
an MEI driver issue. Both have been in linux-next with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWY+zfg8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynOKQCfYPp20/4S/DRl/O9mtFG6+Iczmm8AnAnFUVrN
EHmUF2ipsm4FQ4iZSot3
=yLZO
-----END PGP SIGNATURE-----
Merge tag 'char-misc-4.13-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc fixes from Greg KH:
"Here are two patches for 4.13-rc5.
One is a fix for a reported thunderbolt issue, and the other a fix for
an MEI driver issue. Both have been in linux-next with no reported
issues"
* tag 'char-misc-4.13-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
thunderbolt: Do not enumerate more ports from DROM than the controller has
mei: exclude device from suspend direct complete optimization
We're about to amend ACPI bus scan with DMI checks whether we're running
on a Mac to support Apple device properties in AML. The DMI checks are
performed for every single device, adding overhead for everything x86
that isn't Apple, which is the majority. Rafael and Andy therefore
request to perform the DMI match only once and cache the result.
Outside of ACPI various other Apple DMI checks exist and it seems
reasonable to use the cached value there as well. Rafael, Andy and
Darren suggest performing the DMI check in arch code and making it
available with a header in include/linux/platform_data/x86/.
To this end, add early_platform_quirks() to arch/x86/kernel/quirks.c
to perform the DMI check and invoke it from setup_arch(). Switch over
all existing Apple DMI checks, thereby fixing two deficiencies:
* They are now #defined to false on non-x86 arches and can thus be
optimized away if they're located in cross-arch code.
* Some of them only match "Apple Inc." but not "Apple Computer, Inc.",
which is used by BIOSes released between January 2006 (when the first
x86 Macs started shipping) and January 2007 (when the company name
changed upon introduction of the iPhone).
Suggested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Suggested-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Suggested-by: Darren Hart <dvhart@infradead.org>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
On one of my test machines nhi_mailbox_cmd() called from icm_suspend()
times out and returnes an error which then is propagated to the
caller and causes the entire system suspend to be aborted which isn't
very useful.
Instead of aborting system suspend, print the error into the log
and continue.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Michael Jamet <michael.jamet@intel.com>
- add a missing "!" in the uuid tests
- remove the last remaining user of the uuid_be type, and then
the type and its helpers
-----BEGIN PGP SIGNATURE-----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=FeA7
-----END PGP SIGNATURE-----
Merge tag 'uuid-for-4.13-2' of git://git.infradead.org/users/hch/uuid
Pull uuid fixes from Christoph Hellwig:
- add a missing "!" in the uuid tests
- remove the last remaining user of the uuid_be type, and then the type
and its helpers
* tag 'uuid-for-4.13-2' of git://git.infradead.org/users/hch/uuid:
uuid: remove uuid_be
thunderbolt: use uuid_t instead of uuid_be
uuid: fix incorrect uuid_equal conversion in test_uuid_test
Switch thunderbolt to the new uuid type.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Amir Goldstein <amir73il@gmail.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Firmware upgrade tools that decide which NVM image should be uploaded to
the Thunderbolt controller need to access active parts of the NVM even
if they are not run as root. The information in active NVM is not
considered security critical so we can use the default permissions set
by the NVMem framework.
Writing the NVM image is still left as root only operation.
While there mark the active NVM as read-only in the filesystem.
Reported-by: Yehezkel Bernat <yehezkel.bernat@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andreas Noever <andreas.noever@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Trivial fix to spelling mistake in tb_sw_warn warning message
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Starting from Intel Falcon Ridge the NVM firmware can be upgraded by
using DMA configuration based mailbox commands. If we detect that the
host or device (device support starts from Intel Alpine Ridge) has the
DMA configuration based mailbox we expose NVM information to the
userspace as two separate Linux NVMem devices: nvm_active and
nvm_non_active. The former is read-only portion of the active NVM which
firmware upgrade tools can be use to find out suitable NVM image if the
device identification strings are not enough.
The latter is write-only portion where the new NVM image is to be
written by the userspace. It is up to the userspace to find out right
NVM image (the kernel does very minimal validation). The ICM firmware
itself authenticates the new NVM firmware and fails the operation if it
is not what is expected.
We also expose two new sysfs files per each switch: nvm_version and
nvm_authenticate which can be used to read the active NVM version and
start the upgrade process.
We also introduce safe mode which is the mode a switch goes when it does
not have properly authenticated firmware. In this mode the switch only
accepts a couple of commands including flashing a new NVM firmware image
and triggering power cycle.
This code is based on the work done by Amir Levy and Michael Jamet.
Signed-off-by: Michael Jamet <michael.jamet@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Yehezkel Bernat <yehezkel.bernat@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Andreas Noever <andreas.noever@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Starting from Intel Falcon Ridge the internal connection manager running
on the Thunderbolt host controller has been supporting 4 security
levels. One reason for this is to prevent DMA attacks and only allow
connecting devices the user trusts.
The internal connection manager (ICM) is the preferred way of connecting
Thunderbolt devices over software only implementation typically used on
Macs. The driver communicates with ICM using special Thunderbolt ring 0
(control channel) messages. In order to handle these messages we add
support for the ICM messages to the control channel.
The security levels are as follows:
none - No security, all tunnels are created automatically
user - User needs to approve the device before tunnels are created
secure - User need to approve the device before tunnels are created.
The device is sent a challenge on future connects to be able
to verify it is actually the approved device.
dponly - Only Display Port and USB tunnels can be created and those
are created automatically.
The security levels are typically configurable from the system BIOS and
by default it is set to "user" on many systems.
In this patch each Thunderbolt device will have either one or two new
sysfs attributes: authorized and key. The latter appears for devices
that support secure connect.
In order to identify the device the user can read identication
information, including UUID and name of the device from sysfs and based
on that make a decision to authorize the device. The device is
authorized by simply writing 1 to the "authorized" sysfs attribute. This
is following the USB bus device authorization mechanism. The secure
connect requires an additional challenge step (writing 2 to the
"authorized" attribute) in future connects when the key has already been
stored to the NVM of the device.
Non-ICM systems (before Alpine Ridge) continue to use the existing
functionality and the security level is set to none. For systems with
Alpine Ridge, even on Apple hardware, we will use ICM.
This code is based on the work done by Amir Levy and Michael Jamet.
Signed-off-by: Michael Jamet <michael.jamet@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Yehezkel Bernat <yehezkel.bernat@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Andreas Noever <andreas.noever@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On PCs the NHI host controller is only present when there is a device
connected. When the last device is disconnected the host controller will
dissappear shortly (within 10s). Now if that happens when we are
suspended we should not try to touch the hardware anymore, so add a flag
for this and check it before we re-enable rings.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Yehezkel Bernat <yehezkel.bernat@intel.com>
Reviewed-by: Michael Jamet <michael.jamet@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Andreas Noever <andreas.noever@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The DMA (NHI) port of a switch provides access to the NVM of the host
controller (and devices starting from Intel Alpine Ridge). The NVM
contains also more complete DROM for the root switch including vendor
and device identification strings.
This will look for the DMA port capability for each switch and if found
populates sw->dma_port. We then teach tb_drom_read() to read the DROM
information from NVM if available for the root switch.
The DMA port capability also supports upgrading the NVM for both host
controller and devices which will be added in subsequent patches.
This code is based on the work done by Amir Levy and Michael Jamet.
Signed-off-by: Michael Jamet <michael.jamet@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Yehezkel Bernat <yehezkel.bernat@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Andreas Noever <andreas.noever@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In some cases it is useful to know what is the Thunderbolt generation
the switch supports. This introduces a new field to struct switch that
stores the generation of the switch based on the device ID. Unknown
switches (there should be none) are assumed to be first generation to be
on the safe side.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Yehezkel Bernat <yehezkel.bernat@intel.com>
Reviewed-by: Michael Jamet <michael.jamet@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Andreas Noever <andreas.noever@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The host controller includes two sets of registers that are used to
communicate with the firmware. Add functions that can be used to access
these registers.
This code is based on the work done by Amir Levy and Michael Jamet.
Signed-off-by: Michael Jamet <michael.jamet@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Yehezkel Bernat <yehezkel.bernat@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Andreas Noever <andreas.noever@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add Intel Win Ridge (Thunderbolt 2) and Alpine Ridge (Thunderbolt 3)
controller PCI IDs to the list of supported devices.
This code is based on the work done by Amir Levy and Michael Jamet.
Signed-off-by: Michael Jamet <michael.jamet@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Yehezkel Bernat <yehezkel.bernat@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Andreas Noever <andreas.noever@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If a request times out the response might arrive right after the request
is failed. This response is pushed to the kfifo and next request will
read it instead. Since it most likely will not pass our validation
checks in parse_header() the next request will fail as well, and
response to that request will be pushed to the kfifo, ad infinitum.
We end up in a situation where all requests fail and no devices can be
added anymore until the driver is unloaded and reloaded again.
To overcome this, rework the control channel so that we will have a
queue of outstanding requests. Each request will be handled in turn and
the response is validated against what is expected. Unexpected packets
(for example responses for requests that have been timed out) are
dropped. This model is copied from Greybus implementation with small
changes here and there to get it cope with Thunderbolt control packets.
In addition the configuration packets support sequence number which the
switch is supposed to copy from the request to response. We use this to
drop responses that are already timed out. Taking advantage of the
sequence number, we automatically retry configuration read/write 4 times
before giving up.
Also timeout is not a programming error so there is no need to trigger a
scary backtrace (WARN), instead we just log a warning. After all
Thunderbolt devices are hot-pluggable by definition which means user can
unplug a device any time and that is totally acceptable.
With this change there is no need to take the global domain lock when
sending configuration packets anymore. This is useful when we add
support for cross-domain (XDomain) communication later on.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Yehezkel Bernat <yehezkel.bernat@intel.com>
Reviewed-by: Michael Jamet <michael.jamet@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Andreas Noever <andreas.noever@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently the control channel (ctl.c) handles the one supported
notification (PLUG_EVENT) and sends back ACK accordingly. However, we
are going to add support for the internal connection manager (ICM) that
needs to handle a different notifications. So instead of dealing
everything in the control channel, we change the callback to take an
arbitrary thunderbolt packet and convert the native connection manager
to handle the event itself.
In addition we only push replies we know of to the response FIFO.
Everything else is treated as notification (or request) and is expected
to be dealt by the connection manager implementation.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Yehezkel Bernat <yehezkel.bernat@intel.com>
Reviewed-by: Michael Jamet <michael.jamet@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Andreas Noever <andreas.noever@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We will be using this function in files introduced in subsequent
patches. While there the function is renamed to tb_cfg_make_header()
following tb_cfg_get_route().
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Yehezkel Bernat <yehezkel.bernat@intel.com>
Reviewed-by: Michael Jamet <michael.jamet@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Andreas Noever <andreas.noever@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We are going to use it when we change the connection manager to handle
events itself. Also rename it to follow naming convention used in
functions exposed in ctl.h.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Yehezkel Bernat <yehezkel.bernat@intel.com>
Reviewed-by: Michael Jamet <michael.jamet@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Andreas Noever <andreas.noever@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We will be forwarding notifications received from the control channel to
the connection manager implementations. This way they can decide what to
do if anything when a notification is received.
To be able to use control channel messages from other files, move them
to tb_msgs.h.
No functional changes intended.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Yehezkel Bernat <yehezkel.bernat@intel.com>
Reviewed-by: Michael Jamet <michael.jamet@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Andreas Noever <andreas.noever@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The device DROM contains name of the vendor and device among other
things. Extract this information and expose it to the userspace via two
new attributes.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Yehezkel Bernat <yehezkel.bernat@intel.com>
Reviewed-by: Michael Jamet <michael.jamet@intel.com>
Signed-off-by: Andreas Noever <andreas.noever@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently tb_drom_parse_entry() is only able to parse drom entries of
type TB_DROM_ENTRY_PORT. Rename it to tb_drom_parse_entry_port().
Fold tb_drom_parse_port_entry() into it.
Its return value is currently ignored. Evaluate it and abort parsing on
error.
Change tb_drom_parse_entries() to accommodate for parsing of other entry
types than TB_DROM_ENTRY_PORT.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Andreas Noever <andreas.noever@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are devices out there where CRC32 of the DROM is not correct. One
reason for this is that the ICM firmware does not validate it and it
seems that neither does the Apple driver. To be able to support such
devices we continue parsing the DROM contents regardless of whether
CRC32 failed or not. We still keep the warning there.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Yehezkel Bernat <yehezkel.bernat@intel.com>
Reviewed-by: Michael Jamet <michael.jamet@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Andreas Noever <andreas.noever@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
David S. Miller
Greg Kroah-Hartman
Mika Westerberg
Dan Carpenter
Linus Torvalds
Rafael J. Wysocki
Bernat, Yehezkel
Lukas Wunner
Christoph Hellwig
Colin Ian King