Here is the large set of char/misc/whatever driver subsystem updates for
5.12-rc1. Over time it seems like this tree is collecting more and more
tiny driver subsystems in one place, making it easier for those
maintainers, which is why this is getting larger.
Included in here are:
- coresight driver updates
- habannalabs driver updates
- virtual acrn driver addition (proper acks from the x86
maintainers)
- broadcom misc driver addition
- speakup driver updates
- soundwire driver updates
- fpga driver updates
- amba driver updates
- mei driver updates
- vfio driver updates
- greybus driver updates
- nvmeem driver updates
- phy driver updates
- mhi driver updates
- interconnect driver udpates
- fsl-mc bus driver updates
- random driver fix
- some small misc driver updates (rtsx, pvpanic, etc.)
All of these have been in linux-next for a while, with the only reported
issue being a merge conflict in include/linux/mod_devicetable.h that you
will hit in your tree due to the dfl_device_id addition from the fpga
subsystem in here. The resolution should be simple.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCYDZf9w8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yk3xgCcCEN+pCJTum+uAzSNH3YKs/onaDgAnRSVwOUw
tNW6n1JhXLYl9f5JdhvS
=MOHs
-----END PGP SIGNATURE-----
Merge tag 'char-misc-5.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver updates from Greg KH:
"Here is the large set of char/misc/whatever driver subsystem updates
for 5.12-rc1. Over time it seems like this tree is collecting more and
more tiny driver subsystems in one place, making it easier for those
maintainers, which is why this is getting larger.
Included in here are:
- coresight driver updates
- habannalabs driver updates
- virtual acrn driver addition (proper acks from the x86 maintainers)
- broadcom misc driver addition
- speakup driver updates
- soundwire driver updates
- fpga driver updates
- amba driver updates
- mei driver updates
- vfio driver updates
- greybus driver updates
- nvmeem driver updates
- phy driver updates
- mhi driver updates
- interconnect driver udpates
- fsl-mc bus driver updates
- random driver fix
- some small misc driver updates (rtsx, pvpanic, etc.)
All of these have been in linux-next for a while, with the only
reported issue being a merge conflict due to the dfl_device_id
addition from the fpga subsystem in here"
* tag 'char-misc-5.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (311 commits)
spmi: spmi-pmic-arb: Fix hw_irq overflow
Documentation: coresight: Add PID tracing description
coresight: etm-perf: Support PID tracing for kernel at EL2
coresight: etm-perf: Clarify comment on perf options
ACRN: update MAINTAINERS: mailing list is subscribers-only
regmap: sdw-mbq: use MODULE_LICENSE("GPL")
regmap: sdw: use no_pm routines for SoundWire 1.2 MBQ
regmap: sdw: use _no_pm functions in regmap_read/write
soundwire: intel: fix possible crash when no device is detected
MAINTAINERS: replace my with email with replacements
mhi: Fix double dma free
uapi: map_to_7segment: Update example in documentation
uio: uio_pci_generic: don't fail probe if pdev->irq equals to IRQ_NOTCONNECTED
drivers/misc/vmw_vmci: restrict too big queue size in qp_host_alloc_queue
firewire: replace tricky statement by two simple ones
vme: make remove callback return void
firmware: google: make coreboot driver's remove callback return void
firmware: xilinx: Use explicit values for all enum values
sample/acrn: Introduce a sample of HSM ioctl interface usage
virt: acrn: Introduce an interface for Service VM to control vCPU
...
Device Feature List (DFL) is a linked list of feature headers within the
device MMIO space. It is used by FPGA to enumerate multiple sub features
within it. Each feature can be uniquely identified by DFL type and
feature id, which can be read out from feature headers.
A dfl bus helps DFL framework modularize DFL device drivers for
different sub features. The dfl bus matches its devices and drivers by
DFL type and feature id.
This patch adds dfl bus support to MODULE_DEVICE_TABLE() by adding info
about struct dfl_device_id in devicetable-offsets.c and add a dfl entry
point in file2alias.c.
Acked-by: Wu Hao <hao.wu@intel.com>
Signed-off-by: Xu Yilun <yilun.xu@intel.com>
Signed-off-by: Wu Hao <hao.wu@intel.com>
Signed-off-by: Matthew Gerlach <matthew.gerlach@linux.intel.com>
Signed-off-by: Russ Weight <russell.h.weight@intel.com>
Signed-off-by: Moritz Fischer <mdf@kernel.org>
Link: https://lore.kernel.org/r/20210107043714.991646-6-mdf@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Surface Aggregator EC provides varying functionality, depending on
the Surface device. To manage this functionality, we use dedicated
client devices for each subsystem or virtual device of the EC. While
some of these clients are described as standard devices in ACPI and the
corresponding client drivers can be implemented as platform drivers in
the kernel (making use of the controller API already present), many
devices, especially on newer Surface models, cannot be found there.
To simplify management of these devices, we introduce a new bus and
client device type for the Surface Aggregator subsystem. The new device
type takes care of managing the controller reference, essentially
guaranteeing its validity for as long as the client device exists, thus
alleviating the need to manually establish device links for that purpose
in the client driver (as has to be done with the platform devices).
Signed-off-by: Maximilian Luz <luzmaximilian@gmail.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20201221183959.1186143-7-luzmaximilian@gmail.com
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Add support for the Auxiliary Bus, auxiliary_device and auxiliary_driver.
It enables drivers to create an auxiliary_device and bind an
auxiliary_driver to it.
The bus supports probe/remove shutdown and suspend/resume callbacks.
Each auxiliary_device has a unique string based id; driver binds to
an auxiliary_device based on this id through the bus.
Co-developed-by: Kiran Patil <kiran.patil@intel.com>
Co-developed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Co-developed-by: Fred Oh <fred.oh@linux.intel.com>
Co-developed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Kiran Patil <kiran.patil@intel.com>
Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Signed-off-by: Fred Oh <fred.oh@linux.intel.com>
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Shiraz Saleem <shiraz.saleem@intel.com>
Reviewed-by: Parav Pandit <parav@mellanox.com>
Reviewed-by: Dan Williams <dan.j.williams@intel.com>
Reviewed-by: Martin Habets <mhabets@solarflare.com>
Link: https://lore.kernel.org/r/20201113161859.1775473-2-david.m.ertman@intel.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Link: https://lore.kernel.org/r/160695681289.505290.8978295443574440604.stgit@dwillia2-desk3.amr.corp.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The SoundWire 1.2 specification adds new capabilities that were not
present in previous version, such as the class ID.
To enable support for class drivers, and well as drivers that address
a specific version, all fields of the sdw_device_id structure need to
be exposed. For SoundWire 1.0 and 1.1 devices, a wildcard is used so
class and version information are ignored.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@linux.intel.com>
Reviewed-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20200608205436.2402-4-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Some vendors like HPe or Dell, encode the release version of their BIOS
in the "System BIOS {Major|Minor} Release" fields of Type 0.
This information is used to know which bios release actually runs.
It could be used for some quirks, debugging sessions or inventory tasks.
A typical output for a Dell system running the 65.27 bios is :
[root@t1700 ~]# cat /sys/devices/virtual/dmi/id/bios_release
65.27
[root@t1700 ~]#
Servers that have a BMC encode the release version of their firmware in the
"Embedded Controller Firmware {Major|Minor} Release" fields of Type 0.
This information is used to know which BMC release actually runs.
It could be used for some quirks, debugging sessions or inventory tasks.
A typical output for a Dell system running the 3.75 bmc release is :
[root@t1700 ~]# cat /sys/devices/virtual/dmi/id/ec_firmware_release
3.75
[root@t1700 ~]#
Signed-off-by: Erwan Velu <e.velu@criteo.com>
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Here is the big set of char/misc/other driver patches for 5.7-rc1.
Lots of things in here, and it's later than expected due to some reverts
to resolve some reported issues. All is now clean with no reported
problems in linux-next.
Included in here is:
- interconnect updates
- mei driver updates
- uio updates
- nvmem driver updates
- soundwire updates
- binderfs updates
- coresight updates
- habanalabs updates
- mhi new bus type and core
- extcon driver updates
- some Kconfig cleanups
- other small misc driver cleanups and updates
As mentioned, all have been in linux-next for a while, and with the last
two reverts, all is calm and good.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXodfvA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynzCQCfROhar3E8EhYEqSOP6xq6uhX9uegAnRgGY2rs
rN4JJpOcTddvZcVlD+vo
=ocWk
-----END PGP SIGNATURE-----
Merge tag 'char-misc-5.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver updates from Greg KH:
"Here is the big set of char/misc/other driver patches for 5.7-rc1.
Lots of things in here, and it's later than expected due to some
reverts to resolve some reported issues. All is now clean with no
reported problems in linux-next.
Included in here is:
- interconnect updates
- mei driver updates
- uio updates
- nvmem driver updates
- soundwire updates
- binderfs updates
- coresight updates
- habanalabs updates
- mhi new bus type and core
- extcon driver updates
- some Kconfig cleanups
- other small misc driver cleanups and updates
As mentioned, all have been in linux-next for a while, and with the
last two reverts, all is calm and good"
* tag 'char-misc-5.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (174 commits)
Revert "driver core: platform: Initialize dma_parms for platform devices"
Revert "amba: Initialize dma_parms for amba devices"
amba: Initialize dma_parms for amba devices
driver core: platform: Initialize dma_parms for platform devices
bus: mhi: core: Drop the references to mhi_dev in mhi_destroy_device()
bus: mhi: core: Initialize bhie field in mhi_cntrl for RDDM capture
bus: mhi: core: Add support for reading MHI info from device
misc: rtsx: set correct pcr_ops for rts522A
speakup: misc: Use dynamic minor numbers for speakup devices
mei: me: add cedar fork device ids
coresight: do not use the BIT() macro in the UAPI header
Documentation: provide IBM contacts for embargoed hardware
nvmem: core: remove nvmem_sysfs_get_groups()
nvmem: core: use is_bin_visible for permissions
nvmem: core: use device_register and device_unregister
nvmem: core: add root_only member to nvmem device struct
extcon: axp288: Add wakeup support
extcon: Mark extcon_get_edev_name() function as exported symbol
extcon: palmas: Hide error messages if gpio returns -EPROBE_DEFER
dt-bindings: extcon: usbc-cros-ec: convert extcon-usbc-cros-ec.txt to yaml format
...
Add uevent support to MHI bus so that the client drivers can be autoloaded
by udev when the MHI devices gets created. The client drivers are
expected to provide MODULE_DEVICE_TABLE with the MHI id_table struct so
that the alias can be exported.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Jeffrey Hugo <jhugo@codeaurora.org>
Tested-by: Jeffrey Hugo <jhugo@codeaurora.org>
Link: https://lore.kernel.org/r/20200220095854.4804-13-manivannan.sadhasivam@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since guid_t is the recommended data type for UUIDs in
kernel (and I guess uuid_le is meant to be ultimately
replaced with it), it should be made available here as
well.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Use MODULE_DEVICE_TABLE across several wmi drivers, keeping
wmi_device_id and MODULE_ALIAS() declarations in sync. Add several
Ideapad models to the no_hw_rfkill list. Add support for new Mellanox
platforms, including new fan and LED functionality. Address Dell
keyboard backlight change event and power button release issues. Update
dell_rbu to use appropriate memory allocation mechanisms. Several small
fixes and Ice Lake support for intel_pmc_core. Fix a suspend regression
for Cherry Trail based devices in intel_int0002_vgpio. A few other
routine fixes.
The following is an automated git shortlog grouped by driver:
ACPI / scan:
- Create platform device for BSG2150 ACPI nodes
Documentation/ABI:
- Add new attribute for mlxreg-io sysfs interfaces
- Correct mlxreg-io KernelVersion for 5.0
MAINTAINERS:
- Include mlxreg.h in Mellanox Platform Driver files
asus-wmi:
- Allow loading on systems without the Asus Management GUID
dell-smbios-wmi:
- use MODULE_DEVICE_TABLE() instead of MODULE_ALIAS()
dell-wmi:
- use MODULE_DEVICE_TABLE() instead of MODULE_ALIAS()
- Ignore new keyboard backlight change event
dell-wmi-descriptor:
- use MODULE_DEVICE_TABLE() instead of MODULE_ALIAS()
dell_rbu:
- fix lock imbalance in img_update_realloc
- stop abusing the DMA API
huawei-wmi:
- use MODULE_DEVICE_TABLE() instead of MODULE_ALIAS()
ideapad-laptop:
- Add ideapad 330-15ICH to no_hw_rfkill
- Add S130-14IGM to no_hw_rfkill list
- Add Ideapad 530S-14ARR to no_hw_rfkill list
- Add Yoga C930 to no_hw_rfkill_list
- Add Y530-I5ICH-1060 to no_hw_rfkill list
- Fix no_hw_rfkill_list for Lenovo RESCUER R720-15IKBN
intel-hid:
- Missing power button release on some Dell models
intel-wmi-thunderbolt:
- use MODULE_DEVICE_TABLE() instead of MODULE_ALIAS()
intel_int0002_vgpio:
- Only implement irq_set_wake on Bay Trail
intel_pmc_core:
- Quirk to ignore XTAL shutdown
- Add Package cstates residency info
- Add ICL platform support
- Convert to INTEL_CPU_FAM6 macro
- Avoid a u32 overflow
- Include Reserved IP for LTR
- Fix file permissions for ltr_show
- Fix PCH IP name
- Fix PCH IP sts reading
- Handle CFL regmap properly
leds:
- mlxreg: Add support for capability register
mlx-platform:
- Fix access mode for fan_dir attribute
- Add UID LED for the next generation systems
- Add extra CPLD for next generation systems
- Add support for new VMOD0007 board name
- Add support for fan capability registers
- Add support for fan direction register
modpost:
- file2alias: define size of alias
platform/mellanox:
- mlxreg-hotplug: Fix KASAN warning
platform_data/mlxreg:
- Add capability field to core platform data
- Document fixes for core platform data
touchscreen_dmi:
- Add info for the CHUWI Hi10 Air tablet
- Add info for the Chuwi Hi8 Air tablet
- Add info for the PoV Wintab P1006w (v1.0) tablet
wmi:
- add WMI support to MODULE_DEVICE_TABLE()
- move struct wmi_device_id to mod_devicetable.h
- fix potential null pointer dereference
wmi-bmof:
- use MODULE_DEVICE_TABLE() instead of MODULE_ALIAS()
x86/CPU:
- Add Icelake model number
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEE9M1dh6j+oEL41EZIXFIlAfdBhuEFAlyCu1EACgkQXFIlAfdB
huFASAf/d0Y6uqhLD3G7cL2kXjOWoTE9ouWUwv19bBpnohGmD3OMMap4y1lb6nRR
thCJRhpmX4ObS2adAC4otiOxTzmVoYGsuS9kfBwhKIby2VYHCCxxaTUs6bzMdOfV
GsbaMA+vfb29bU4DcWlRtYZIz2FC5oyjW4ZmcMA6KtuBGjG9K1fG5zANQe4H8I0e
zCdcrXhpDGIBJgaJR2N42EUCJruPoEXYfHa1G4B/QKvuW0CXHAdSE0YrN4ju+S3e
Ew9ZXhoxRaqlu+ZB7H5Kyy6Mg3ZGMzbeYyQFLk5f2yiKSTFNiqwTEJl1aE2JSpy3
g8Im+6E44/4G8QOL40g5XwmrxHw5mA==
=Bx4o
-----END PGP SIGNATURE-----
Merge tag 'platform-drivers-x86-v5.1-1' of git://git.infradead.org/linux-platform-drivers-x86
Pull x86 platform driver updates from Darren Hart:
- use MODULE_DEVICE_TABLE across several wmi drivers, keeping
wmi_device_id and MODULE_ALIAS() declarations in sync
- add several Ideapad models to the no_hw_rfkill list
- add support for new Mellanox platforms, including new fan and LED
functionality
- address Dell keyboard backlight change event and power button release
issues
- update dell_rbu to use appropriate memory allocation mechanisms
- several small fixes and Ice Lake support for intel_pmc_core
- fix a suspend regression for Cherry Trail based devices in
intel_int0002_vgpio
- a few other routine fixes
* tag 'platform-drivers-x86-v5.1-1' of git://git.infradead.org/linux-platform-drivers-x86: (50 commits)
MAINTAINERS: Include mlxreg.h in Mellanox Platform Driver files
platform/x86: ideapad-laptop: Add S130-14IGM to no_hw_rfkill list
platform/x86: mlx-platform: Fix access mode for fan_dir attribute
platform/x86: mlx-platform: Add UID LED for the next generation systems
platform/x86: mlx-platform: Add extra CPLD for next generation systems
platform/x86: wmi-bmof: use MODULE_DEVICE_TABLE() instead of MODULE_ALIAS()
platform/x86: intel-wmi-thunderbolt: use MODULE_DEVICE_TABLE() instead of MODULE_ALIAS()
platform/x86: huawei-wmi: use MODULE_DEVICE_TABLE() instead of MODULE_ALIAS()
platform/x86: dell-wmi: use MODULE_DEVICE_TABLE() instead of MODULE_ALIAS()
platform/x86: dell-wmi-descriptor: use MODULE_DEVICE_TABLE() instead of MODULE_ALIAS()
platform/x86: dell-smbios-wmi: use MODULE_DEVICE_TABLE() instead of MODULE_ALIAS()
platform/x86: wmi: add WMI support to MODULE_DEVICE_TABLE()
platform/x86: wmi: move struct wmi_device_id to mod_devicetable.h
modpost: file2alias: define size of alias
platform/x86: touchscreen_dmi: Add info for the CHUWI Hi10 Air tablet
platform/x86: ideapad-laptop: Add Ideapad 530S-14ARR to no_hw_rfkill list
platform/x86: ideapad-laptop: Add Yoga C930 to no_hw_rfkill_list
platform/x86: intel_pmc_core: Quirk to ignore XTAL shutdown
platform/x86: intel_pmc_core: Add Package cstates residency info
platform/x86: intel_pmc_core: Add ICL platform support
...
The kernel provides the macro MODULE_DEVICE_TABLE() where driver authors
can specify their device type and their array of device_ids and thereby
trigger the generation of the appropriate MODULE_ALIAS() output. This is
opposed to having to specify one MODULE_ALIAS() for each device. The WMI
device type is currently not supported.
While using MODULE_DEVICE_TABLE() does increase the complexity as well
as spreading out the implementation across the kernel, it does come with
some benefits too;
* It makes different drivers look more similar; if you can specify the
array of device_ids any device type specific input to MODULE_ALIAS()
will automatically be generated for you.
* It helps each driver avoid keeping multiple versions of the same
information in sync. That is, both the array of device_ids and the
potential multitude of MODULE_ALIAS()'s.
Add WMI support to MODULE_DEVICE_TABLE() by adding info about struct
wmi_device_id in devicetable-offsets.c and add a WMI entry point in
file2alias.c.
The type argument for MODULE_DEVICE_TABLE(type, name) is wmi.
Suggested-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Mattias Jacobsson <2pi@mok.nu>
Acked-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>
In preparation for adding WMI support to MODULE_DEVICE_TABLE() move the
definition of struct wmi_device_id to mod_devicetable.h and inline
guid_string in the struct.
Changing guid_string to an inline char array changes the loop conditions
when looping over an array of struct wmi_device_id. Therefore update
wmi_dev_match()'s loop to check for an empty guid_string instead of a
NULL pointer.
Signed-off-by: Mattias Jacobsson <2pi@mok.nu>
[dvhart: Move UUID_STRING_LEN define to this patch]
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>
The size of the variable alias provided to do_entry functions are
currently not readily available. Thus hindering do_entry functions to
perform bounds checking.
Define the macro ALIAS_SIZE containing the size of the variable alias.
Signed-off-by: Mattias Jacobsson <2pi@mok.nu>
Acked-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>
Introduce a generic TEE bus driver concept for TEE based kernel drivers
which would like to communicate with TEE based devices/services. Also
add support in module device table for these new TEE based devices.
In this TEE bus concept, devices/services are identified via Universally
Unique Identifier (UUID) and drivers register a table of device UUIDs
which they can support.
So this TEE bus framework registers following apis:
- match(): Iterates over the driver UUID table to find a corresponding
match for device UUID. If a match is found, then this particular device
is probed via corresponding probe api registered by the driver. This
process happens whenever a device or a driver is registered with TEE
bus.
- uevent(): Notifies user-space (udev) whenever a new device is registered
on this bus for auto-loading of modularized drivers.
Also this framework allows for device enumeration to be specific to
corresponding TEE implementation like OP-TEE etc.
Signed-off-by: Sumit Garg <sumit.garg@linaro.org>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Reviewed-by: Bhupesh Sharma <bhsharma@redhat.com>
Signed-off-by: Jens Wiklander <jens.wiklander@linaro.org>
Use specific prototype instead of an opaque pointer so that the
compiler can catch function prototype mismatch.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Mathieu Malaterre <malat@debian.org>
Commit e49ce14150 ("modpost: use linker section to generate table.")
was not so cool as we had expected first; it ended up with ugly section
hacks when commit dd2a3acaec ("mod/file2alias: make modpost compile
on darwin again") came in.
Given a certain degree of unknowledge about the link stage of host
programs, I really want to see simple, stupid table lookup so that
this works in the same way regardless of the underlying executable
format.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Mathieu Malaterre <malat@debian.org>
Create DEF_FIELD_ADDR_VAR as a more generic version of the DEF_FIELD_ADD
macro, allowing usage of a variable name other than the struct element name.
Also, sets DEF_FIELD_ADDR as a specific usage of DEF_FILD_ADDR_VAR in which
the var name is the same as the struct element name.
Then, makes use of DEF_FIELD_ADDR_VAR to create a variable of another name,
in order to avoid variable shadowing.
Signed-off-by: Leonardo Bras <leobras.c@gmail.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Blackfin and metag were the only architectures that prefix symbols with
an underscore. They were removed by commit 4ba66a9760 ("arch: remove
blackfin port"), commit bb6fb6dfcc ("metag: Remove arch/metag/"),
respectively.
It is no longer necessary to handle <prefix> part of module device
table symbols.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Introducing a simple bus for the alternate modes. Bus allows
binding drivers to the discovered alternate modes the
partners support.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Tested-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Due to missing a missing entry in file2alias.c MODULE_DEVICE_TABLE() are
not generating the proper module aliases. Add the needed entry here.
Fixes: bcabbccabf ("rpmsg: add virtio-based remote processor messaging bus")
Reported-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This adds the base SoundWire bus type, bus and driver registration.
along with changes to module device table for new SoundWire
device type.
Signed-off-by: Sanyog Kale <sanyog.r.kale@intel.com>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Acked-By: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Several conflicts here.
NFP driver bug fix adding nfp_netdev_is_nfp_repr() check to
nfp_fl_output() needed some adjustments because the code block is in
an else block now.
Parallel additions to net/pkt_cls.h and net/sch_generic.h
A bug fix in __tcp_retransmit_skb() conflicted with some of
the rbtree changes in net-next.
The tc action RCU callback fixes in 'net' had some overlap with some
of the recent tcf_block reworking.
Signed-off-by: David S. Miller <davem@davemloft.net>
The commit 8724ecb072 ("Input: allow matching device IDs on property
bits") started using property bits when generating module aliases for input
handlers, but did not adjust the generation of MODALIAS attribute on input
device uevents, breaking automatic module loading. Given that no handler
currently uses property bits in their module tables, let's revert this part
of the commit for now.
Reported-by: Damien Wyart <damien.wyart@gmail.com>
Tested-by: Damien Wyart <damien.wyart@gmail.com>
Fixes: 8724ecb072 ("Input: allow matching device IDs on property bits")
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
There were quite a few overlapping sets of changes here.
Daniel's bug fix for off-by-ones in the new BPF branch instructions,
along with the added allowances for "data_end > ptr + x" forms
collided with the metadata additions.
Along with those three changes came veritifer test cases, which in
their final form I tried to group together properly. If I had just
trimmed GIT's conflict tags as-is, this would have split up the
meta tests unnecessarily.
In the socketmap code, a set of preemption disabling changes
overlapped with the rename of bpf_compute_data_end() to
bpf_compute_data_pointers().
Changes were made to the mv88e6060.c driver set addr method
which got removed in net-next.
The hyperv transport socket layer had a locking change in 'net'
which overlapped with a change of socket state macro usage
in 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
Let's allow matching input devices on their property bits, both in-kernel
and when generating module aliases.
Tested-by: Roderick Colenbrander <roderick.colenbrander@sony.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
When two hosts are connected over a Thunderbolt cable, there is a
protocol they can use to communicate capabilities supported by the host.
The discovery protocol uses automatically configured control channel
(ring 0) and is build on top of request/response transactions using
special XDomain primitives provided by the Thunderbolt base protocol.
The capabilities consists of a root directory block of basic properties
used for identification of the host, and then there can be zero or more
directories each describing a Thunderbolt service and its capabilities.
Once both sides have discovered what is supported the two hosts can
setup high-speed DMA paths and transfer data to the other side using
whatever protocol was agreed based on the properties. The software
protocol used to communicate which DMA paths to enable is service
specific.
This patch adds support for the XDomain discovery protocol to the
Thunderbolt bus. We model each remote host connection as a Linux XDomain
device. For each Thunderbolt service found supported on the XDomain
device, we create Linux Thunderbolt service device which Thunderbolt
service drivers can then bind to based on the protocol identification
information retrieved from the property directory describing the
service.
This code is based on the work done by Amir Levy and Michael Jamet.
Signed-off-by: Michael Jamet <michael.jamet@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Yehezkel Bernat <yehezkel.bernat@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the definition of fsl_mc_device_id to its proper location in
mod_devicetable.h, and add fsl-mc bus support to devicetable-offsets.c
and file2alias.c to enable device table matching. With this patch udev
based module loading of fsl-mc drivers is supported.
Signed-off-by: Stuart Yoder <stuart.yoder@nxp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Because of an improper dereference, a stray 'C' character was output to
the modalias when no 'compatible' was specified. This is the case for
some old PowerMac drivers which only set the 'name' property. Fix it to
let them match again.
Reported-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Tested-by: Mathieu Malaterre <malat@debian.org>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Cc: Andreas Schwab <schwab@linux-m68k.org>
Fixes: 6543becf26 ("mod/file2alias: make modalias generation safe for cross compiling")
Cc: stable@vger.kernel.org # v3.9+
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Since the wildcard at the end of OF module aliases is gone, autoloading
of modules that don't match a device's last (most generic) compatible
value fails.
For example the CODA960 VPU on i.MX6Q has the SoC specific compatible
"fsl,imx6q-vpu" and the generic compatible "cnm,coda960". Since the
driver currently only works with knowledge about the SoC specific
integration, it doesn't list "cnm,cod960" in the module device table.
This results in the device compatible
"of:NvpuT<NULL>Cfsl,imx6q-vpuCcnm,coda960" not matching the module alias
"of:N*T*Cfsl,imx6q-vpu" anymore, whereas before commit 2f632369ab
("modpost: don't add a trailing wildcard for OF module aliases") it
matched the module alias "of:N*T*Cfsl,imx6q-vpu*".
This patch adds two module aliases for each compatible, one without the
wildcard and one with "C*" appended.
$ modinfo coda | grep imx6q
alias: of:N*T*Cfsl,imx6q-vpuC*
alias: of:N*T*Cfsl,imx6q-vpu
Fixes: 2f632369ab ("modpost: don't add a trailing wildcard for OF module aliases")
Link: http://lkml.kernel.org/r/1462203339-15340-1-git-send-email-p.zabel@pengutronix.de
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Cc: Javier Martinez Canillas <javier@osg.samsung.com>
Cc: Brian Norris <computersforpeace@gmail.com>
Cc: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: <stable@vger.kernel.org> [4.5+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit ac55182899 ("modpost: i2c aliases need no trailing wildcard")
removed the wildcard at the end of the I2C module aliases because I2C
devices have no IDs so the aliases are just arbitrary device names.
This is also true for OF modaliases since a compatible string is used to
define a specific IP hardware block. So the modalias should match a
specific compatible string and not attempt to match a compatible string
whose name matches the beginning of another one.
For example, the following driver module:
$ modinfo cros_ec_keyb | grep alias
alias: platform:cros-ec-keyb
alias: of:N*T*Cgoogle,cros-ec-keyb*
will be tried to be loaded for an alias of:N*T*Cgoogle,cros-ec-keyb-v2
but there could be a different driver that supports the device for that
compatible string so it's better to remove the trailing wildcard for OF.
Also, remove the word "always" from the add_wildcard() function comment
since that was carried from the time where a wildcard was always added
at the end of the module alias for all the devices.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Suggested-by: Brian Norris <computersforpeace@gmail.com>
Reviewed-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Consistently use uuid_le type in the Hyper-V driver code.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here is the first batch of updates for sound system on 4.4-rc1.
Again at this time, the update looks fairly calm; no big changes in
either ALSA core or ASoC infrastructures, rather all small cleanups,
in addition to the new stuff as usual.
The biggest changes are about Firewire sound devices. It gained lots
of new device support, and MIDI functionality. Also there are updates
for a few still working-in-progress stuff (topology API and ASoC
skylake), too. But overall, this update should give no big surprise.
Some highlight is below:
Core:
- A few more Kconfig items for tinification; it's marked as EXPERT,
so normal user should't be bothered :)
- Refactoring with a new PCM hw_constraint helper
- Removal of unused transfer_ack_{begin,end} PCM callbacks
Firewire:
- Restructuring of code subtree, lots of refactoring
- Support AMDTP variants
- New driver for Digidesign 002/003 family
- Adds support for TASCAM FireOne to ALSA OXFW driver
- Add MIDI support to TASCAM and Digi00x devices
HD-Audio:
- Automated modalias generation for codec drivers, finally
- Improvement on heuristics for setting mixer name
- A few fixes for longstanding bugs on Creative CA0132 cards
- Addition of audio rate callback with i915 communication
- Fix suspend issue on recent Dell XPS
- Intel Lewisburg controller support
ASoC:
- Updates to the topology userspace interface
- Big updates to the Renesas support (rcar)
- More updates for supporting Intel Sky Lake systems
- New drivers for Asahi Kasei Microdevices AK4613, Allwinnner A10,
Cirrus Logic WM8998, Dialog DA7219, Nuvoton NAU8825, Rockchip
S/PDIF, and Atmel class D amplifier
USB-Audio:
- A fix for newer Roland MIDI devices
- Quirks and workarounds for Zoom R16/24 device
Misc:
- A few fixes for some old Cirrus CS46xx PCI sound boards
- Yet another fixes for some old ESS Maestro3 PCI sound boards
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=l9SO
-----END PGP SIGNATURE-----
Merge tag 'sound-4.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound updates from Takashi Iwai:
"Here is the first batch of updates for sound system on 4.4-rc1.
Again at this time, the update looks fairly calm; no big changes in
either ALSA core or ASoC infrastructures, rather all small cleanups,
in addition to the new stuff as usual.
The biggest changes are about Firewire sound devices. It gained lots
of new device support, and MIDI functionality. Also there are updates
for a few still working-in-progress stuff (topology API and ASoC
skylake), too. But overall, this update should give no big surprise.
Some highlights are below:
Core:
- A few more Kconfig items for tinification; it's marked as EXPERT,
so normal user should't be bothered :)
- Refactoring with a new PCM hw_constraint helper
- Removal of unused transfer_ack_{begin,end} PCM callbacks
Firewire:
- Restructuring of code subtree, lots of refactoring
- Support AMDTP variants
- New driver for Digidesign 002/003 family
- Adds support for TASCAM FireOne to ALSA OXFW driver
- Add MIDI support to TASCAM and Digi00x devices
HD-Audio:
- Automated modalias generation for codec drivers, finally
- Improvement on heuristics for setting mixer name
- A few fixes for longstanding bugs on Creative CA0132 cards
- Addition of audio rate callback with i915 communication
- Fix suspend issue on recent Dell XPS
- Intel Lewisburg controller support
ASoC:
- Updates to the topology userspace interface
- Big updates to the Renesas support (rcar)
- More updates for supporting Intel Sky Lake systems
- New drivers for Asahi Kasei Microdevices AK4613, Allwinnner A10,
Cirrus Logic WM8998, Dialog DA7219, Nuvoton NAU8825, Rockchip
S/PDIF, and Atmel class D amplifier
USB-Audio:
- A fix for newer Roland MIDI devices
- Quirks and workarounds for Zoom R16/24 device
Misc:
- A few fixes for some old Cirrus CS46xx PCI sound boards
- Yet another fixes for some old ESS Maestro3 PCI sound boards"
* tag 'sound-4.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (330 commits)
ALSA: hda - Add Intel Lewisburg device IDs Audio
ALSA: hda - Apply pin fixup for HP ProBook 6550b
ALSA: hda - Fix lost 4k BDL boundary workaround
ALSA: maestro3: Fix Allegro mute until master volume/mute is touched
ALSA: maestro3: Enable docking support for Dell Latitude C810
ALSA: firewire-digi00x: add another rawmidi character device for MIDI control ports
ALSA: firewire-digi00x: add MIDI operations for MIDI control port
ALSA: firewire-digi00x: rename identifiers of MIDI operation for physical ports
ALSA: cs46xx: Fix suspend for all channels
ALSA: cs46xx: Fix Duplicate front for CS4294 and CS4298 codecs
ALSA: DocBook: Add soc-ops.c and soc-compress.c
ALSA: hda - Add / fix kernel doc comments
ALSA: Constify ratden/ratnum constraints
ALSA: hda - Disable 64bit address for Creative HDA controllers
ALSA: hda/realtek - Dell XPS one ALC3260 speaker no sound after resume back
ALSA: hda/ca0132 - Convert leftover pr_info() and pr_err()
ASoC: fsl: Use #ifdef instead of #if for CONFIG_PM_SLEEP
ASoC: rt5645: Sort the order for register bit defines
ASoC: dwc: add check for master/slave format
ASoC: rt5645: Add the HWEQ for the speaker output
...
For generating modalias entries automatically, move the definition of
struct hda_device_id to linux/mod_devicetable.h and add the handling
of this record in file2alias helper. The new modalias is represented
with combination of vendor id, device id, and api version as
"hdaudio:vNrNaN".
This patch itself doesn't convert the existing modaliases. Since they
were added manually, this patch won't give any regression by itself at
this point.
[Modified the modalias format to adapt the api_version field, and drop
invalid ANY_ID definition by tiwai]
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Reviewed-by: Vinod Koul <vinod.koul@intel.com>
Tested-by: Subhransu S Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The device alias now looks like mei:S:uuid:N:*
In that way we can bind different drivers to clients with
different protocol versions if required.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
scripts/mod/file2alias.c:add_uuid() convert UUID into a single string
which does not conform to the standard little endian UUID formatting.
This patch changes add_uuid() to output same format as %pUL and modifies
the mei driver to match the change.
Signed-off-by: Prarit Bhargava <prarit@redhat.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Device drivers typically use ACPI _HIDs/_CIDs listed in struct device_driver
acpi_match_table to match devices. However, for generic drivers, we do not
want to list _HID for all supported devices. Also, certain classes of devices
do not have _CID (e.g. SATA, USB). Instead, we can leverage ACPI _CLS,
which specifies PCI-defined class code (i.e. base-class, subclass and
programming interface). This patch adds support for matching ACPI devices using
the _CLS method.
To support loadable module, current design uses _HID or _CID to match device's
modalias. With the new way of matching with _CLS this would requires modification
to the current ACPI modalias key to include _CLS. This patch appends PCI-defined
class-code to the existing ACPI modalias as following.
acpi:<HID>:<CID1>:<CID2>:..:<CIDn>:<bbsspp>:
E.g:
# cat /sys/devices/platform/AMDI0600:00/modalias
acpi:AMDI0600:010601:
where bb is th base-class code, ss is te sub-class code, and pp is the
programming interface code
Since there would not be _HID/_CID in the ACPI matching table of the driver,
this patch adds a field to acpi_device_id to specify the matching _CLS.
static const struct acpi_device_id ahci_acpi_match[] = {
{ ACPI_DEVICE_CLASS(PCI_CLASS_STORAGE_SATA_AHCI, 0xffffff) },
{},
};
In this case, the corresponded entry in modules.alias file would be:
alias acpi*:010601:* ahci_platform
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Hanjun Guo <hanjun.guo@linaro.org>
Signed-off-by: Suravee Suthikulpanit <Suravee.Suthikulpanit@amd.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Here's the big USB patchset for 4.2-rc1. As is normal these days, the
majority of changes are in the gadget drivers, with a bunch of other
small driver changes.
All of these have been in linux-next with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlWNobIACgkQMUfUDdst+ylXtQCgwTnzFBzly+3h1Npa2CWkr/Lw
TWAAn31qEP28MLjm8iVJLNPwdVd2kt1w
=hrdz
-----END PGP SIGNATURE-----
Merge tag 'usb-4.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB updates from Greg KH:
"Here's the big USB patchset for 4.2-rc1. As is normal these days, the
majority of changes are in the gadget drivers, with a bunch of other
small driver changes.
All of these have been in linux-next with no reported issues"
* tag 'usb-4.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (175 commits)
usb: dwc3: Use ASCII space in Kconfig
usb: chipidea: add work-around for Marvell HSIC PHY startup
usb: chipidea: allow multiple instances to use default ci_default_pdata
dt-bindings: Consolidate ChipIdea USB ci13xxx bindings
phy: add Marvell HSIC 28nm PHY
phy: Add Marvell USB 2.0 OTG 28nm PHY
dt-bindings: Add Marvell PXA1928 USB and HSIC PHY bindings
USB: ssb: use devm_kzalloc
USB: ssb: fix error handling in ssb_hcd_create_pdev()
usb: isp1760: check for null return from kzalloc
cdc-acm: Add support of ATOL FPrint fiscal printers
usb: chipidea: usbmisc_imx: Remove unneeded semicolon
USB: usbtmc: add device quirk for Rigol DS6104
USB: serial: mos7840: Use setup_timer
phy: twl4030-usb: add ABI documentation
phy: twl4030-usb: remove incorrect pm_runtime_get_sync() in probe function.
phy: twl4030-usb: remove pointless 'suspended' test in 'suspend' callback.
phy: twl4030-usb: make runtime pm more reliable.
drivers:usb:fsl: Fix compilation error for fsl ehci drv
usb: renesas_usbhs: Don't disable the pipe if Control write status stage
...
A previous commit, c93b76b34b ("mei: bus: report also uuid in module
alias") caused a build error as I missed applying a needed patch to add
some macros to uapi/linux/uuid.h. Instead of those additional macros,
change the mei code to use the existing uuid structure directly.
Fixes: c93b76b34b
Cc: Tomas Winkler <tomas.winkler@intel.com>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In order to automate modules matching add device uuid
which is reported in client enumeration, keep also
the name that is needed in for nfc distinguishing radio vendor
Report mei:name:uuid
Cc: linux-api@vger.kernel.org
Cc: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
UTMI+ Low Pin Interface (ULPI) is a commonly used PHY
interface for USB 2.0. The ULPI specification describes a
standard set of registers which the vendors can extend for
their specific needs. ULPI PHYs provide often functions
such as charger detection and ADP sensing and probing.
There are two major issues that the bus type is meant to
tackle:
Firstly, ULPI registers are accessed from the controller.
The bus provides convenient method for the controller
drivers to share that access with the actual PHY drivers.
Secondly, there are already platforms that assume ULPI PHYs
are runtime detected, such as many Intel Baytrail based
platforms. They do not provide any kind of hardware
description for the ULPI PHYs like separate ACPI device
object that could be used to enumerate a device from.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: David Cohen <david.a.cohen@linux.intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Add MIPS Common Device Memory Map (CDMM) support in the form of a bus in
the standard Linux device model. Each device attached via CDMM is
discoverable via an 8-bit type identifier and may contain a number of
blocks of memory mapped registers in the CDMM region. IRQs are expected
to be handled separately.
Due to the per-cpu (per-VPE for MT cores) nature of the CDMM devices,
all the driver callbacks take place from workqueues which are run on the
right CPU for the device in question, so that the driver doesn't need to
be as concerned about which CPU it is running on. Callbacks also exist
for when CPUs are taken offline, so that any per-CPU resources used by
the driver can be disabled so they don't get forcefully migrated. CDMM
devices are created as children of the CPU device they are attached to.
Any existing CDMM configuration by the bootloader will be inherited,
however platforms wishing to enable CDMM should implement the weak
mips_cdmm_phys_base() function (see asm/cdmm.h) so that the bus driver
knows where it should put the CDMM region in the physical address space
if the bootloader hasn't already enabled it.
A mips_cdmm_early_probe() function is also provided to allow early boot
or particularly low level code to set up the CDMM region and probe for a
specific device type, for example early console or KGDB IO drivers for
the EJTAG Fast Debug Channel (FDC) CDMM device.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/9599/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
a staging driver; fix included. Greg KH said he'd take the patch
but hadn't as the merge window opened, so it's included here
to avoid breaking build.
Cheers,
Rusty.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=yzUO
-----END PGP SIGNATURE-----
Merge tag 'modules-next-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux
Pull module updates from Rusty Russell:
"Nothing major: the stricter permissions checking for sysfs broke a
staging driver; fix included. Greg KH said he'd take the patch but
hadn't as the merge window opened, so it's included here to avoid
breaking build"
* tag 'modules-next-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux:
staging: fix up speakup kobject mode
Use 'E' instead of 'X' for unsigned module taint flag.
VERIFY_OCTAL_PERMISSIONS: stricter checking for sysfs perms.
kallsyms: fix percpu vars on x86-64 with relocation.
kallsyms: generalize address range checking
module: LLVMLinux: Remove unused function warning from __param_check macro
Fix: module signature vs tracepoints: add new TAINT_UNSIGNED_MODULE
module: remove MODULE_GENERIC_TABLE
module: allow multiple calls to MODULE_DEVICE_TABLE() per module
module: use pr_cont
Commit 78551277e4df5: "Input: i8042 - add PNP modaliases" had a bug, where the
second call to MODULE_DEVICE_TABLE() overrode the first resulting in not all
the modaliases being exposed.
This fixes the problem by including the name of the device_id table in the
__mod_*_device_table alias, allowing us to export several device_id tables
per module.
Suggested-by: Kay Sievers <kay@vrfy.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Tom Gundersen <teg@jklm.no>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
The x86 CPU feature modalias handling existed before it was reimplemented
generically. This patch aligns the x86 handling so that it
(a) reuses some more code that is now generic;
(b) uses the generic format for the modalias module metadata entry, i.e., it
now uses 'cpu:type:x86,venVVVVfamFFFFmodMMMM:feature:,XXXX,YYYY' instead of
the 'x86cpu:vendor:VVVV👪FFFF:model:MMMM:feature:,XXXX,YYYY' that was
used before.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Acked-by: H. Peter Anvin <hpa@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds support for advertising optional CPU features over udev
using the modalias, and for declaring compatibility with/dependency upon
such a feature in a module.
The mapping between feature numbers and actual features should be provided
by the architecture in a file called <asm/cpufeature.h> which exports the
following functions/macros:
- cpu_feature(FEAT), a preprocessor macro that maps token FEAT to a
numeric index;
- bool cpu_have_feature(n), returning whether this CPU has support for
feature #n;
- MAX_CPU_FEATURES, an upper bound for 'n' in the previous function.
The feature can then be enabled by setting CONFIG_GENERIC_CPU_AUTOPROBE
for the architecture.
For instance, a module that registers its module init function using
module_cpu_feature_match(FEAT_X, module_init_function)
will be probed automatically when the CPU's support for the 'FEAT_X'
feature is advertised over udev, and will only allow the module to be
loaded by hand if the 'FEAT_X' feature is supported.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit afe2dab4f6 ("USB: add hex/bcd detection to usb modalias generation")
changed the routine that generates alias ranges. Before that change, only
digits 0-9 were supported; the commit tried to fix the case when the range
includes higher values than 0x9.
Unfortunately, the commit didn't fix the case when the range includes both
0x9 and 0xA, meaning that the final range must look like [x-9A-y] where
x <= 0x9 and y >= 0xA -- instead the [x-9A-x] range was produced.
Modprobe doesn't complain as it sees no difference between no-match and
bad-pattern results of fnmatch().
Fixing this simple bug to fix the aliases.
Also changing the hardcoded beginning of the range to uppercase as all the
other letters are also uppercase in the device version numbers.
Fortunately, this affects only the dvb-usb-dib0700 module, AFAIK.
Signed-off-by: Jan Moskyto Matejka <mq@suse.cz>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull kbuild updates from Michal Marek:
- fix for make headers_install argv explosion with too long path
- scripts/setlocalversion does not call git update-index needlessly
- fix for the src.rpm produced by make rpm-pkg. The new make
image_name can be useful also for other packaging tools.
- scripts/mod/devicetable-offsets.o is not rebuilt during each make run
- make modules_install dependency fix
- scripts/sortextable portability fix
- fix for kbuild to generate the output directory for all object files
in subdirs.
- a couple of minor fixes
* 'kbuild' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild:
kbuild: create directory for dir/file.o
tools/include: use stdint types for user-space byteshift headers
Makefile: Fix install error with make -j option
Fix a build warning in scripts/mod/file2alias.c
improve modalias building
scripts/mod: Spelling s/DEVICEVTABLE/DEVICETABLE/
kbuild: fix error when building from src rpm
scripts/setlocalversion on write-protected source tree
Makefile.lib: align DTB quiet_cmd
kbuild: fix make headers_install when path is too long
Add RapidIO-specific modalias generation to enable udev notifications
about RapidIO-specific events.
The RapidIO modalias string format is shown below:
"rapidio:vNNNNdNNNNavNNNNadNNNN"
Where:
v - Device Vendor ID (16 bit),
d - Device ID (16 bit),
av - Assembly Vendor ID (16 bit),
ad - Assembly ID (16 bit),
as they are reported in corresponding Capability Registers (CARs)
of each RapidIO device.
Signed-off-by: Alexandre Bounine <alexandre.bounine@idt.com>
Cc: Matt Porter <mporter@kernel.crashing.org>
Cc: Li Yang <leoli@freescale.com>
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: Andre van Herk <andre.van.herk@Prodrive.nl>
Cc: Micha Nelissen <micha.nelissen@Prodrive.nl>
Cc: Stef van Os <stef.van.os@Prodrive.nl>
Cc: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds
Xu Yilun
Maximilian Luz
Dave Ertman
Pierre-Louis Bossart
Erwan Velu
Manivannan Sadhasivam
Boris Brezillon
Heikki Krogerus
Mattias Jacobsson
Sumit Garg
Masahiro Yamada
Leonardo Bras
Andrew F. Davis
Vinod Koul
David S. Miller
Dmitry Torokhov
Mika Westerberg
Stuart Yoder
Wolfram Sang
Philipp Zabel
Javier Martinez Canillas
K. Y. Srinivasan
Subhransu S. Prusty
Tomas Winkler
Prarit Bhargava
Suthikulpanit, Suravee
Greg Kroah-Hartman
James Hogan
Masahiro Yamada
Tom Gundersen
Ard Biesheuvel
Jan Moskyto Matejka
Alexandre Bounine