Adding avx512 gen_syndrome and recovery functions so as to allow code to
be compiled and tested successfully in userspace.
This patch is tested in userspace and improvement in performace is
observed.
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Jim Kukunas <james.t.kukunas@linux.intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: Megha Dey <megha.dey@linux.intel.com>
Signed-off-by: Gayatri Kammela <gayatri.kammela@intel.com>
Reviewed-by: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: Shaohua Li <shli@fb.com>
Optimize RAID6 recovery functions to take advantage of
the 512-bit ZMM integer instructions introduced in AVX512.
AVX512 optimized recovery functions, which is simply based
on recov_avx2.c written by Jim Kukunas
This patch was tested and benchmarked before submission on
a hardware that has AVX512 flags to support such instructions
Cc: Jim Kukunas <james.t.kukunas@linux.intel.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: Megha Dey <megha.dey@linux.intel.com>
Signed-off-by: Gayatri Kammela <gayatri.kammela@intel.com>
Reviewed-by: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: Shaohua Li <shli@fb.com>
Optimize RAID6 gen_syndrom functions to take advantage of
the 512-bit ZMM integer instructions introduced in AVX512.
AVX512 optimized gen_syndrom functions, which is simply based
on avx2.c written by Yuanhan Liu and sse2.c written by hpa.
The patch was tested and benchmarked before submission on
a hardware that has AVX512 flags to support such instructions
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Jim Kukunas <james.t.kukunas@linux.intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: Megha Dey <megha.dey@linux.intel.com>
Signed-off-by: Gayatri Kammela <gayatri.kammela@intel.com>
Reviewed-by: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: Shaohua Li <shli@fb.com>
The XC instruction can be used to improve the speed of the raid6
recovery. The loops now operate on blocks of 256 bytes.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The enable_kernel_*() functions leave the relevant MSR bits enabled
until we exit the kernel sometime later. Create disable versions
that wrap the kernel use of FP, Altivec VSX or SPE.
While we don't want to disable it normally for performance reasons
(MSR writes are slow), it will be used for a debug boot option that
does this and catches bad uses in other areas of the kernel.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
- Disable the 32-bit vdso when building LE, so we can build with a 64-bit only
toolchain.
- EEH fixes from Gavin & Richard.
- Enable the sys_kcmp syscall from Laurent.
- Sysfs control for fastsleep workaround from Shreyas.
- Expose OPAL events as an irq chip by Alistair.
- MSI ops moved to pci_controller_ops by Daniel.
- Fix for kernel to userspace backtraces for perf from Anton.
- Merge pseries and pseries_le defconfigs from Cyril.
- CXL in-kernel API from Mikey.
- OPAL prd driver from Jeremy.
- Fix for DSCR handling & tests from Anshuman.
- Powernv flash mtd driver from Cyril.
- Dynamic DMA Window support on powernv from Alexey.
- LLVM clang fixes & workarounds from Anton.
- Reworked version of the patch to abort syscalls when transactional.
- Fix the swap encoding to support 4TB, from Aneesh.
- Various fixes as usual.
- Freescale updates from Scott: Highlights include more 8xx optimizations, an
e6500 hugetlb optimization, QMan device tree nodes, t1024/t1023 support, and
various fixes and cleanup.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=d9Wh
-----END PGP SIGNATURE-----
Merge tag 'powerpc-4.2-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mpe/linux
Pull powerpc updates from Michael Ellerman:
- disable the 32-bit vdso when building LE, so we can build with a
64-bit only toolchain.
- EEH fixes from Gavin & Richard.
- enable the sys_kcmp syscall from Laurent.
- sysfs control for fastsleep workaround from Shreyas.
- expose OPAL events as an irq chip by Alistair.
- MSI ops moved to pci_controller_ops by Daniel.
- fix for kernel to userspace backtraces for perf from Anton.
- merge pseries and pseries_le defconfigs from Cyril.
- CXL in-kernel API from Mikey.
- OPAL prd driver from Jeremy.
- fix for DSCR handling & tests from Anshuman.
- Powernv flash mtd driver from Cyril.
- dynamic DMA Window support on powernv from Alexey.
- LLVM clang fixes & workarounds from Anton.
- reworked version of the patch to abort syscalls when transactional.
- fix the swap encoding to support 4TB, from Aneesh.
- various fixes as usual.
- Freescale updates from Scott: Highlights include more 8xx
optimizations, an e6500 hugetlb optimization, QMan device tree nodes,
t1024/t1023 support, and various fixes and cleanup.
* tag 'powerpc-4.2-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mpe/linux: (180 commits)
cxl: Fix typo in debug print
cxl: Add CXL_KERNEL_API config option
powerpc/powernv: Fix wrong IOMMU table in pnv_ioda_setup_bus_dma()
powerpc/mm: Change the swap encoding in pte.
powerpc/mm: PTE_RPN_MAX is not used, remove the same
powerpc/tm: Abort syscalls in active transactions
powerpc/iommu/ioda2: Enable compile with IOV=on and IOMMU_API=off
powerpc/include: Add opal-prd to installed uapi headers
powerpc/powernv: fix construction of opal PRD messages
powerpc/powernv: Increase opal-irqchip initcall priority
powerpc: Make doorbell check preemption safe
powerpc/powernv: pnv_init_idle_states() should only run on powernv
macintosh/nvram: Remove as unused
powerpc: Don't use gcc specific options on clang
powerpc: Don't use -mno-strict-align on clang
powerpc: Only use -mtraceback=no, -mno-string and -msoft-float if toolchain supports it
powerpc: Only use -mabi=altivec if toolchain supports it
powerpc: Fix duplicate const clang warning in user access code
vfio: powerpc/spapr: Support Dynamic DMA windows
vfio: powerpc/spapr: Register memory and define IOMMU v2
...
The -mabi=altivec option is not recognised on LLVM, so use call cc-option
to check for support.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
We already have fpu/types.h, move i387.h to fpu/api.h.
The file name has become a misnomer anyway: it offers generic FPU APIs,
but is not limited to i387 functionality.
Reviewed-by: Borislav Petkov <bp@alien8.de>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The second and (last) optimized XOR syndrome calculation. This version
supports right and left side optimization. All CPUs with architecture
older than Haswell will benefit from it.
It should be noted that SSE2 movntdq kills performance for memory areas
that are read and written simultaneously in chunks smaller than cache
line size. So use movdqa instead for P/Q writes in sse21 and sse22 XOR
functions.
Signed-off-by: Markus Stockhausen <stockhausen@collogia.de>
Signed-off-by: NeilBrown <neilb@suse.de>
Start the algorithms with the very basic one. It is left and right
optimized. That means we can avoid all calculations for unneeded pages
above the right stop offset. For pages below the left start offset we
still need the syndrome multiplication but without reading data pages.
Signed-off-by: Markus Stockhausen <stockhausen@collogia.de>
Signed-off-by: NeilBrown <neilb@suse.de>
It is always helpful to have a test tool in place if we implement
new data critical algorithms. So add some test routines to the raid6
checker that can prove if the new xor_syndrome() works as expected.
Run through all permutations of start/stop pages per algorithm and
simulate a xor_syndrome() assisted rmw run. After each rmw check if
the recovery algorithm still confirms that the stripe is fine.
Signed-off-by: Markus Stockhausen <stockhausen@collogia.de>
Signed-off-by: NeilBrown <neilb@suse.de>
v3: s-o-b comment, explanation of performance and descision for
the start/stop implementation
Implementing rmw functionality for RAID6 requires optimized syndrome
calculation. Up to now we can only generate a complete syndrome. The
target P/Q pages are always overwritten. With this patch we provide
a framework for inplace P/Q modification. In the first place simply
fill those functions with NULL values.
xor_syndrome() has two additional parameters: start & stop. These
will indicate the first and last page that are changing during a
rmw run. That makes it possible to avoid several unneccessary loops
and speed up calculation. The caller needs to implement the following
logic to make the functions work.
1) xor_syndrome(disks, start, stop, ...): "Remove" all data of source
blocks inside P/Q between (and including) start and end.
2) modify any block with start <= block <= stop
3) xor_syndrome(disks, start, stop, ...): "Reinsert" all data of
source blocks into P/Q between (and including) start and end.
Pages between start and stop that won't be changed should be filled
with a pointer to the kernel zero page. The reasons for not taking NULL
pages are:
1) Algorithms cross the whole source data line by line. Thus avoid
additional branches.
2) Having a NULL page avoids calculating the XOR P parity but still
need calulation steps for the Q parity. Depending on the algorithm
unrolling that might be only a difference of 2 instructions per loop.
The benchmark numbers of the gen_syndrome() functions are displayed in
the kernel log. Do the same for the xor_syndrome() functions. This
will help to analyze performance problems and give an rough estimate
how well the algorithm works. The choice of the fastest algorithm will
still depend on the gen_syndrome() performance.
With the start/stop page implementation the speed can vary a lot in real
life. E.g. a change of page 0 & page 15 on a stripe will be harder to
compute than the case where page 0 & page 1 are XOR candidates. To be not
to enthusiatic about the expected speeds we will run a worse case test
that simulates a change on the upper half of the stripe. So we do:
1) calculation of P/Q for the upper pages
2) continuation of Q for the lower (empty) pages
Signed-off-by: Markus Stockhausen <stockhausen@collogia.de>
Signed-off-by: NeilBrown <neilb@suse.de>
Just like for AVX2 (which simply needs an #if -> #ifdef conversion),
SSSE3 assembler support should be checked for before using it.
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Cc: Jim Kukunas <james.t.kukunas@linux.intel.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: NeilBrown <neilb@suse.de>
Headline item is multithreading for RAID5 so that more
IO/sec can be supported on fast (SSD) devices.
Also TILE-Gx SIMD suppor for RAID6 calculations and an
assortment of bug fixes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)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=zLxh
-----END PGP SIGNATURE-----
Merge tag 'md/3.12' of git://neil.brown.name/md
Pull md update from Neil Brown:
"Headline item is multithreading for RAID5 so that more IO/sec can be
supported on fast (SSD) devices. Also TILE-Gx SIMD suppor for RAID6
calculations and an assortment of bug fixes"
* tag 'md/3.12' of git://neil.brown.name/md:
raid5: only wakeup necessary threads
md/raid5: flush out all pending requests before proceeding with reshape.
md/raid5: use seqcount to protect access to shape in make_request.
raid5: sysfs entry to control worker thread number
raid5: offload stripe handle to workqueue
raid5: fix stripe release order
raid5: make release_stripe lockless
md: avoid deadlock when dirty buffers during md_stop.
md: Don't test all of mddev->flags at once.
md: Fix apparent cut-and-paste error in super_90_validate
raid6/test: replace echo -e with printf
RAID: add tilegx SIMD implementation of raid6
md: fix safe_mode buglet.
md: don't call md_allow_write in get_bitmap_file.
-e is a non-standard echo option, echo output is
implementation-dependent when it is used. Replace echo -e with printf as
suggested by POSIX echo manual.
Cc: NeilBrown <neilb@suse.de>
Cc: Jim Kukunas <james.t.kukunas@linux.intel.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Yuanhan Liu <yuanhan.liu@linux.intel.com>
Acked-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
This change adds TILE-Gx SIMD instructions to the software raid
(md), modeling the Altivec implementation. This is only for Syndrome
generation; there is more that could be done to improve recovery,
as in the recent Intel SSE3 recovery implementation.
The code unrolls 8 times; this turns out to be the best on tilegx
hardware among the set 1, 2, 4, 8 or 16. The code reads one
cache-line of data from each disk, stores P and Q then goes to the
next cache-line.
The test code in sys/linux/lib/raid6/test reports 2008 MB/s data
read rate for syndrome generation using 18 disks (16 data and 2
parity). It was 1512 MB/s before this SIMD optimizations. This is
running on 1 core with all the data in cache.
This is based on the paper The Mathematics of RAID-6.
(http://kernel.org/pub/linux/kernel/people/hpa/raid6.pdf).
Signed-off-by: Ken Steele <ken@tilera.com>
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Rebased/reworked a patch contributed by Rob Herring that uses
NEON intrinsics to perform the RAID-6 syndrome calculations.
It uses the existing unroll.awk code to generate several
unrolled versions of which the best performing one is selected
at boot time.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Acked-by: Nicolas Pitre <nico@linaro.org>
Cc: hpa@linux.intel.com
sse and avx2 stuff only exist on x86 arch, and we don't need to build
altivec on x86. And we can do that at lib/raid6/Makefile.
Proposed-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Yuanhan Liu <yuanhan.liu@linux.intel.com>
Reviewed-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Jim Kukunas <james.t.kukunas@linux.intel.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Add AVX2 optimized gen_syndrom functions, which is simply based on
sse2.c written by hpa.
Signed-off-by: Yuanhan Liu <yuanhan.liu@linux.intel.com>
Reviewed-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Jim Kukunas <james.t.kukunas@linux.intel.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Optimize RAID6 recovery functions to take advantage of
the 256-bit YMM integer instructions introduced in AVX2.
The patch was tested and benchmarked before submission.
However hardware is not yet released so benchmark numbers
cannot be reported.
Acked-by: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: Jim Kukunas <james.t.kukunas@linux.intel.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Make the recovery functions static to fix the following sparse warnings:
lib/raid6/recov.c:25:6: warning: symbol 'raid6_2data_recov_intx1' was
not declared. Should it be static?
lib/raid6/recov.c:69:6: warning: symbol 'raid6_datap_recov_intx1' was
not declared. Should it be static?
lib/raid6/recov_ssse3.c:22:6: warning: symbol 'raid6_2data_recov_ssse3'
was not declared. Should it be static?
lib/raid6/recov_ssse3.c:197:6: warning: symbol 'raid6_datap_recov_ssse3'
was not declared. Should it be static?
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Jim Kukunas <james.t.kukunas@linux.intel.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Reorders functions in raid6_algos as well as the preference check
to reduce the number of functions tested on initialization.
Also, creates symmetry between choosing the gen_syndrome functions
and choosing the recovery functions.
Signed-off-by: Jim Kukunas <james.t.kukunas@linux.intel.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Test each combination of recovery and syndrome generation
functions.
Signed-off-by: Jim Kukunas <james.t.kukunas@linux.intel.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Add SSSE3 optimized recovery functions, as well as a system
for selecting the most appropriate recovery functions to use.
Originally-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Jim Kukunas <james.t.kukunas@linux.intel.com>
Signed-off-by: NeilBrown <neilb@suse.de>
<linux/module.h> drags in headers which are not visible to userspace,
thus breaking the build for the test program.
Signed-off-by: Jim Kukunas <james.t.kukunas@linux.intel.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Remove all #inclusions of asm/system.h preparatory to splitting and killing
it. Performed with the following command:
perl -p -i -e 's!^#\s*include\s*<asm/system[.]h>.*\n!!' `grep -Irl '^#\s*include\s*<asm/system[.]h>' *`
Signed-off-by: David Howells <dhowells@redhat.com>
Disintegrate asm/system.h for PowerPC.
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
cc: linuxppc-dev@lists.ozlabs.org
These files were getting the defines for EXPORT_SYMBOL because
device.h was including module.h. But we are going to put an
end to that. So add the proper export.h include now.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
A pending cleanup will mean that module.h won't be implicitly
everywhere anymore. Make sure the modular drivers in md dir
are actually calling out for <module.h> explicitly in advance.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
The files were renamed in commit cc4589ebf; fix the name in the file
itself.
Signed-off-by: Dan McGee <dpmcgee@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Gayatri Kammela
Martin Schwidefsky
Anton Blanchard
Ard Biesheuvel
Linus Torvalds
Ingo Molnar
Markus Stockhausen
Jan Beulich
Max Filippov
Ken Steele
Yuanhan Liu
Jim Kukunas
David Howells
Paul Gortmaker
Dan McGee
NeilBrown
David Woodhouse
David Woodhouse