Граф коммитов

2669 Коммитов

Автор SHA1 Сообщение Дата
Tejun Heo 867974fc09 ahci_imx: depend on CONFIG_MFD_SYSCON
ahci_imx makes use of regmap but the dependency wasn't specified in
Kconfig leading build failures if CONFIG_AHCI_IMX is enabled but
CONFIG_MFD_SYSCON is not.  Add the Kconfig dependency.

Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
2013-07-26 08:57:56 -04:00
Richard Zhu 9e54eae23b ahci_imx: add ahci sata support on imx platforms
imx6q contains one Synopsys AHCI SATA controller, But it can't share
ahci_platform driver with other controllers because there are some
misalignments of the generic AHCI controller - the bits definitions of
the HBA registers, the Vendor Specific registers, the AHCI PHY clock
and the AHCI signals adjustment window(GPR13 register).

 - CAP_SSS(bit20) of the HOST_CAP is writable, default value is '0',
   should be configured to be '1'

 - bit0 (only one AHCI SATA port on imx6q) of the HOST_PORTS_IMPL
   should be set to be '1'.(default 0)

 - One Vendor Specific register HOST_TIMER1MS(offset:0xe0) should be
   configured regarding to the frequency of AHB bus clock.

 - Configurations of the AHCI PHY clock, and the signal parameters of
   the GPR13

Setup its own ahci sata driver, contained the imx6q specific
initialized codes, re-use the generic ahci_platform driver, and keep
the generic ahci_platform driver clean as much as possible.

tj: patch description reformatted

Signed-off-by: Richard Zhu <r65037@freescale.com>
Reviewed-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Tejun Heo <tj@kernel.org>
2013-07-24 12:29:08 -04:00
Xiaotian Feng c91bc6ccd1 ahci: fix Null pointer dereference in achi_host_active()
commit b29900e6 (AHCI: Make distinct names for ports in /proc/interrupts)
introuded a regression, which resulted Null pointer dereference for achi
host with dummy ports. For ahci ports, when the port is dummy port, its
private_data will be NULL, as ata_dummy_port_ops doesn't support ->port_start.

changes in v2: use pp to check dummy ports, update comments

Reported-and-tested-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Xiaotian Feng <xtfeng@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Alexander Gordeev <agordeev@redhat.com>
Cc: linux-ide@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
2013-07-23 10:25:32 -04:00
Tejun Heo bb96961928 libata: make it clear that sata_inic162x is experimental
sata_inic162x never reached a state where it's reliable enough for
production use and data corruption is a relatively common occurrence.
Make the driver generate warning about the issues and mark the Kconfig
option as experimental.

If the situation doesn't improve, we'd be better off making it depend
on CONFIG_BROKEN.  Let's wait for several cycles and see if the kernel
message draws any attention.

Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Martin Braure de Calignon <braurede@free.fr>
Reported-by: Ben Hutchings <ben@decadent.org.uk>
Reported-by: risc4all@yahoo.com
2013-07-22 17:11:14 -04:00
Jingoo Han 42b9ab7ab7 libata: replace strict_strtol() with kstrtol()
The usage of strict_strtol() is not preferred, because
strict_strtol() is obsolete. Thus, kstrtol() should be
used.

Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
2013-07-22 16:15:01 -04:00
Youquan Song eac27f04a7 ata: Fix DVD not dectected at some platform with Wellsburg PCH
There is a patch b55f84e2d5 "ata_piix: Fix DVD
 not dectected at some Haswell platforms" to fix an issue of DVD not
recognized on Haswell Desktop platform with Lynx Point.
Recently, it is also found the same issue at some platformas with Wellsburg PCH.

So deliver a similar patch to fix it by disables 32bit PIO in IDE mode.

Signed-off-by: Youquan Song <youquan.song@intel.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: stable@vger.kernel.org
2013-07-16 05:52:02 -06:00
Linus Torvalds d144746478 Merge branch 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus
Pull MIPS updates from Ralf Baechle:
 "MIPS updates:

   - All the things that didn't make 3.10.
   - Removes the Windriver PPMC platform.  Nobody will miss it.
   - Remove a workaround from kernel/irq/irqdomain.c which was there
     exclusivly for MIPS.  Patch by Grant Likely.
   - More small improvments for the SEAD 3 platform
   - Improvments on the BMIPS / SMP support for the BCM63xx series.
   - Various cleanups of dead leftovers.
   - Platform support for the Cavium Octeon-based EdgeRouter Lite.

  Two large KVM patchsets didn't make it for this pull request because
  their respective authors are vacationing"

* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (124 commits)
  MIPS: Kconfig: Add missing MODULES dependency to VPE_LOADER
  MIPS: BCM63xx: CLK: Add dummy clk_{set,round}_rate() functions
  MIPS: SEAD3: Disable L2 cache on SEAD-3.
  MIPS: BCM63xx: Enable second core SMP on BCM6328 if available
  MIPS: BCM63xx: Add SMP support to prom.c
  MIPS: define write{b,w,l,q}_relaxed
  MIPS: Expose missing pci_io{map,unmap} declarations
  MIPS: Malta: Update GCMP detection.
  Revert "MIPS: make CAC_ADDR and UNCAC_ADDR account for PHYS_OFFSET"
  MIPS: APSP: Remove <asm/kspd.h>
  SSB: Kconfig: Amend SSB_EMBEDDED dependencies
  MIPS: microMIPS: Fix improper definition of ISA exception bit.
  MIPS: Don't try to decode microMIPS branch instructions where they cannot exist.
  MIPS: Declare emulate_load_store_microMIPS as a static function.
  MIPS: Fix typos and cleanup comment
  MIPS: Cleanup indentation and whitespace
  MIPS: BMIPS: support booting from physical CPU other than 0
  MIPS: Only set cpu_has_mmips if SYS_SUPPORTS_MICROMIPS
  MIPS: GIC: Fix gic_set_affinity infinite loop
  MIPS: Don't save/restore OCTEON wide multiplier state on syscalls.
  ...
2013-07-13 14:52:21 -07:00
Linus Torvalds 9e220385c4 Merge branch 'for-3.11' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata
Pull libata updates from Tejun Heo:
 "Overview of changes:

   - The rest of maintainer email address updates.

   - Some core updates - more robust default behavior for port
     multipliers, better error reporting for SG_IO commands, and a way
     to better work around now ancient and probably pretty rare PATA ->
     SATA bridges with ATAPI devices.

   - sata_rcar stabilization.

   - Some hardware PCI ID additions and one-off low level driver
     updates."

* 'for-3.11' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata: (22 commits)
  AHCI: use ATA_BUSY
  libata-zpodd: must use ata_tf_init()
  ahci: AHCI-mode SATA patch for Intel Coleto Creek DeviceIDs
  ata_piix: IDE-mode SATA patch for Intel Coleto Creek DeviceIDs
  libata: cleanup SAT error translation
  ahci: sata: add support for exynos5440 sata
  libata: skip SRST for all SIMG [34]7x port-multipliers
  ahci: remove pmp link online check in FBS EH
  sata highbank: add bit-banged SGPIO driver support
  ahci: make ahci_transmit_led_message into a function pointer
  sata_rcar: fix compilation warning in sata_rcar_thaw()
  sata_highbank: increase retry count but shorten duration for Calxeda controller
  ata: use pci_get_drvdata()
  ipr: qc_fill_rtf() method should not store alternate status register
  sata_rcar: add 'base' local variable to some functions
  sata_rcar: correct 'sata_rcar_sht'
  sata_rcar: kill superfluous code in sata_rcar_bmdma_fill_sg()
  libata: do not limit R-Car SATA driver to shmobile
  ata: use platform_{get,set}_drvdata()
  AHCI: Make distinct names for ports in /proc/interrupts
  ...
2013-07-03 19:49:46 -07:00
Linus Torvalds 862f001254 PCI changes for the v3.11 merge window:
PCI device hotplug
     - Add pci_alloc_dev() interface (Gu Zheng)
     - Add pci_bus_get()/put() for reference counting (Jiang Liu)
     - Fix SR-IOV reference count issues (Jiang Liu)
     - Remove unused acpi_pci_roots list (Jiang Liu)
 
   MSI
     - Conserve interrupt resources on x86 (Alexander Gordeev)
 
   AER
     - Force fatal severity when component has been reset (Betty Dall)
     - Reset link below Root Port as well as Downstream Port (Betty Dall)
     - Fix "Firmware first" flag setting (Bjorn Helgaas)
     - Don't parse HEST for non-PCIe devices (Bjorn Helgaas)
 
   ASPM
     - Warn when we can't disable ASPM as driver requests (Bjorn Helgaas)
 
   Miscellaneous
     - Add CircuitCo PCI IDs (Darren Hart)
     - Add AMD CZ SATA and SMBus PCI IDs (Shane Huang)
     - Work around Ivytown NTB BAR size issue (Jon Mason)
     - Detect invalid initial BAR values (Kevin Hao)
     - Add pcibios_release_device() (Sebastian Ott)
     - Fix powerpc & sparc PCI_UNKNOWN power state usage (Bjorn Helgaas)
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1.4.11 (GNU/Linux)
 
 iQIcBAABAgAGBQJR0dhDAAoJEFmIoMA60/r8AUoP/RrKOXC2GGZCqUIKjUyxaCU+
 NXwaNhjfRuge5lZHE8fUAnYVveFTv0iNo8if/md866/pS4il3vxaMWRhZrBddXqe
 juyxPUGaOb5NmI2C+g5ebQ1xHhnOU6kWrgQ5kQk5GmJdm6BpiWDCFaalyioYj27v
 FoN/25IG+5EtJjP6kRdQGFZq+RYOqlBfQp4fdFmY5bDsQiCLREH6YWHeNSkH+t1I
 Eh84WESqGzgaZyCb9QKM2AcU/HMKLux4VXAYp9idVr3tH1j9b/klQI7xNW7sPnkY
 LIzKTcfF89iXkhxc7zrF0O/n5rC5Cp7LQpiFMV6yCT3w25yWpq9itOwqcZ/nfCv6
 fje8P1B2lwGrizkwKKLcosTzWkJewvfLkVye90WS3g0i3zlijF4pfEiw3a2ujA91
 MP9/JmX+ZZ5QeGyPuFmYJyMlInH4vtSdegl9jtaeuX4cOnuMP+Ouxnxc+mH2bOfl
 Z5/K1OSCYLfb27uWM7od2lgb+GFHLMP+RMy073h0ZMpDvM6EnZy5iu1zU9+yJO4S
 8/aRhBz4h+YEBinnXOJvHzMfu3wQQ7UvXZqEspgsug2Z5xHvxhMLhrJQgpVUSdsW
 Nrdm1dNdACV/cvt/lWzUE7SmUaOua/r/cVmViF2ryeRET7t65in+5NHXmXP8ET+r
 1WA7pbykfegC9uY84PaK
 =X3Lo
 -----END PGP SIGNATURE-----

Merge tag 'pci-v3.11-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci

Pull PCI changes from Bjorn Helgaas:
 "PCI device hotplug
    - Add pci_alloc_dev() interface (Gu Zheng)
    - Add pci_bus_get()/put() for reference counting (Jiang Liu)
    - Fix SR-IOV reference count issues (Jiang Liu)
    - Remove unused acpi_pci_roots list (Jiang Liu)

  MSI
    - Conserve interrupt resources on x86 (Alexander Gordeev)

  AER
    - Force fatal severity when component has been reset (Betty Dall)
    - Reset link below Root Port as well as Downstream Port (Betty Dall)
    - Fix "Firmware first" flag setting (Bjorn Helgaas)
    - Don't parse HEST for non-PCIe devices (Bjorn Helgaas)

  ASPM
    - Warn when we can't disable ASPM as driver requests (Bjorn Helgaas)

  Miscellaneous
    - Add CircuitCo PCI IDs (Darren Hart)
    - Add AMD CZ SATA and SMBus PCI IDs (Shane Huang)
    - Work around Ivytown NTB BAR size issue (Jon Mason)
    - Detect invalid initial BAR values (Kevin Hao)
    - Add pcibios_release_device() (Sebastian Ott)
    - Fix powerpc & sparc PCI_UNKNOWN power state usage (Bjorn Helgaas)"

* tag 'pci-v3.11-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (51 commits)
  MAINTAINERS: Add ACPI folks for ACPI-related things under drivers/pci
  PCI: Add CircuitCo vendor ID and subsystem ID
  PCI: Use pdev->pm_cap instead of pci_find_capability(..,PCI_CAP_ID_PM)
  PCI: Return early on allocation failures to unindent mainline code
  PCI: Simplify IOV implementation and fix reference count races
  PCI: Drop redundant setting of bus->is_added in virtfn_add_bus()
  unicore32/PCI: Remove redundant call of pci_bus_add_devices()
  m68k/PCI: Remove redundant call of pci_bus_add_devices()
  PCI / ACPI / PM: Use correct power state strings in messages
  PCI: Fix comment typo for pcie_pme_remove()
  PCI: Rename pci_release_bus_bridge_dev() to pci_release_host_bridge_dev()
  PCI: Fix refcount issue in pci_create_root_bus() error recovery path
  ia64/PCI: Clean up pci_scan_root_bus() usage
  PCI/AER: Reset link for devices below Root Port or Downstream Port
  ACPI / APEI: Force fatal AER severity when component has been reset
  PCI/AER: Remove "extern" from function declarations
  PCI/AER: Move AER severity defines to aer.h
  PCI/AER: Set dev->__aer_firmware_first only for matching devices
  PCI/AER: Factor out HEST device type matching
  PCI/AER: Don't parse HEST table for non-PCIe devices
  ...
2013-07-03 16:31:35 -07:00
Tejun Heo 5a0a6a4f17 Merge branch 'libata/for-3.10-fixes' into libata/for-3.11
libata/for-3.10-fixes never got submitted during v3.10 cycle.  Merge
it into for-3.11 so that it can be routed together with other changes
scheduled for v3.11.

Three trivial conflicts in drivers/ata/sata_rcar.c.  All are caused by
1b20f6a9ad ("sata_rcar: add 'base' local variable to some functions")
conflicting with logic updates in for-3.10-fixes.  The offending
commit simply adds local variable @base on functions which
dereferences sata_rcar_priv->base multiple times.  The resolutions are
trivial - applying s/priv->base/base/ in the conflicting logic
updates.

Signed-off-by: Tejun Heo <tj@kernel.org>
2013-07-02 19:54:16 -07:00
Rafael J. Wysocki e52cff8bdd Merge branch 'pm-assorted'
* pm-assorted:
  PM / QoS: Add pm_qos and dev_pm_qos to events-power.txt
  PM / QoS: Add dev_pm_qos_request tracepoints
  PM / QoS: Add pm_qos_request tracepoints
  PM / QoS: Add pm_qos_update_target/flags tracepoints
  PM / QoS: Update Documentation/power/pm_qos_interface.txt
  PM / Sleep: Print last wakeup source on failed wakeup_count write
  PM / QoS: correct the valid range of pm_qos_class
  PM / wakeup: Adjust messaging for wake events during suspend
  PM / Runtime: Update .runtime_idle() callback documentation
  PM / Runtime: Rework the "runtime idle" helper routine
  PM / Hibernate: print physical addresses consistently with other parts of kernel
2013-06-28 13:01:40 +02:00
Sergei Shtylyov 9bbb1b0e2a AHCI: use ATA_BUSY
ahci_hardreset() and ahci_p5wdh_hardreset() use bare numbers for the
BSY bit of the ATA status register, despite it's #define'd in
<linux/ata.h>.

Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
2013-06-24 16:29:31 -07:00
Aaron Lu 44521527be libata-acpi: add back ACPI based hotplug functionality
Commit 30dcf76acc "libata: migrate ACPI code over to new bindings"
mistakenly dropped the code to register hotplug notificaion handler
for ATA port/devices, causing regression for people using ATA bay,
as kernel bug #59871 shows.

Fix this by adding back the hotplug notification handler registration
code.  Since this code has to be run once and notification needs to
be installed on every ATA port/devices handle no matter if there is
actual device attached, we can't do this in binding time for ATA
device ACPI handle, as the binding only occurs when a SCSI device is
created, i.e. there is device attached.  So introduce the
ata_acpi_hotplug_init() function to loop scan all ATA ACPI handles
and if it is available, install the notificaion handler for it during
ATA init time.

With the ATA ACPI handle binding to SCSI device tree, it is possible
now that when the SCSI hotplug work removes the SCSI device, the ACPI
unbind function will find that the corresponding ACPI device has
already been deleted by dock driver, causing a scaring message like:
[  128.263966] scsi 4:0:0:0: Oops, 'acpi_handle' corrupt
Fix this by waiting for SCSI hotplug task finish in our notificaion
handler, so that the removal of ACPI device done in ACPI unbind
function triggered by the removal of SCSI device is run earlier when
ACPI device is still available.

[rjw: Rebased]
References: https://bugzilla.kernel.org/show_bug.cgi?id=59871
Reported-bisected-and-tested-by: Dirk Griesbach <spamthis@freenet.de>
Signed-off-by: Aaron Lu <aaron.lu@intel.com>
Acked-by: Tejun Heo <tj@kernel.org>
Cc: 3.6+ <stable@vger.kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2013-06-25 00:51:33 +02:00
Sergei Shtylyov d0887c43f5 libata-zpodd: must use ata_tf_init()
There are  some SATA controllers which have both devices 0 and 1 but this module
just zeroes out taskfile and sets then ATA_TFLAG_DEVICE (not sure that's needed)
which could  lead to a wrong device being selected just before issuing command.
Thus we should  call ata_tf_init()  which sets  up the device register value
properly, like  all other users of ata_exec_internal() do...

Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: stable@vger.kernel.org
2013-06-24 15:45:28 -07:00
Seth Heasley 1cfc7df3de ahci: AHCI-mode SATA patch for Intel Coleto Creek DeviceIDs
This patch adds the AHCI-mode SATA DeviceIDs for the Intel Coleto Creek PCH.

Signed-off-by: Seth Heasley <seth.heasley@intel.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: stable@vger.kernel.org
2013-06-21 11:40:58 -07:00
Seth Heasley c7e8695bfa ata_piix: IDE-mode SATA patch for Intel Coleto Creek DeviceIDs
This patch adds the IDE-mode SATA DeviceIDs for the Intel Coleto Creek PCH.

Signed-off-by: Seth Heasley <seth.heasley@intel.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: stable@vger.kernel.org
2013-06-21 11:40:30 -07:00
Gwendal Grignou 78062c50d1 libata: cleanup SAT error translation
- Remove duplicate Medium Error Entry.

- Fix translations to match SAT2 translation table.

- Remove warning messages when translation is not found when decoding
  error or status register.

- Goes through status register decoding when only ABRT bit is set in
  error register.

Tested: When a disk fails, it sets

  Status = 0x71 [DRDY DF ERR] , Error = 0x4 [ABRT]

This patch will make the sense key HARDWARE_ERROR instead.

When there is a simple command syntax error:

  Status = 0x51 [DRDY ERR] , Error = 0x4 [ABRT]

The sense key remains ABORTED_COMMAND.

tj: Some updates to the description and comments.

Signed-off-by: Gwendal Grignou <gwendal@google.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
2013-06-18 11:35:30 -07:00
Girish K S 1e8f5f761c ahci: sata: add support for exynos5440 sata
This patch adds the compatible string of the exynos5440 sata controller
compliant with the ahci 1.3 and sata 3.0 specification.

changes in v2:
		changed the compatible string by adding the actual IP
owners name instead of the SoC vendor name.

Signed-off-by: Girish K S <ks.giri@samsung.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
2013-06-17 11:23:05 -07:00
Tejun Heo 7a87718d92 libata: skip SRST for all SIMG [34]7x port-multipliers
For some reason, a lot of port-multipliers have issues with softreset.
SIMG [34]7x series port-multipliers have been quite erratic in this
regard.  I recall that it was better with some firmware revisions and
the current list of quirks worked fine for a while.  I think it got
worse with later firmwares or maybe my test coverage wasn't good
enough.  Anyways, HPA is reporting that his 3726 setup suffers SRST
failures and then the PMP gets confused and fails to probe the last
port.

The hope was that we try to stick to the standard as much as possible
and soonish the PMPs and their firmwares will improve in quality, so
the quirk list was kept to minimum.  Well, it seems like that's never
gonna happen.

Let's set NO_SRST for all [34]7x PMPs so that whatever remaining
userbase of the device suffer the least.  Maybe we should do the same
for 57xx's but unfortunately I don't have any device left to test and
I'm not even sure 57xx's have ever been made widely available, so
let's leave those alone for now.

Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: "H. Peter Anvin" <hpa@zytor.com>
Cc: stable@vger.kernel.org
2013-06-11 00:14:34 -07:00
David Daney 9ddebc46e7 MIPS: OCTEON: Rename Kconfig CAVIUM_OCTEON_REFERENCE_BOARD to CAVIUM_OCTEON_SOC
CAVIUM_OCTEON_SOC most place we used to use CPU_CAVIUM_OCTEON.  This
allows us to CPU_CAVIUM_OCTEON in places where we have no OCTEON SOC.

Remove CAVIUM_OCTEON_SIMULATOR as it doesn't really do anything, we can
get the same configuration with CAVIUM_OCTEON_SOC.

Signed-off-by: David Daney <david.daney@cavium.com>
Cc: linux-mips@linux-mips.org
Cc: linux-ide@vger.kernel.org
Cc: linux-edac@vger.kernel.org
Cc: linux-i2c@vger.kernel.org
Cc: netdev@vger.kernel.org
Cc: spi-devel-general@lists.sourceforge.net
Cc: devel@driverdev.osuosl.org
Cc: linux-usb@vger.kernel.org
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Patchwork: https://patchwork.linux-mips.org/patch/5295/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2013-06-10 18:01:25 +02:00
Shane Huang 912b9ac683 ahci: remove pmp link online check in FBS EH
ata_link_online() check in ahci_error_intr() is unnecessary, it should
be removed otherwise may lead to lockup with FBS enabled PMP.
http://marc.info/?l=linux-ide&m=137050421603272&w=2

Reported-by: Yu Liu <liuyu.ac@gmail.com>
Signed-off-by: Shane Huang <shane.huang@amd.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: stable@vger.kernel.org
2013-06-09 14:54:32 -07:00
Mark Langsdorf d50b110f14 sata highbank: add bit-banged SGPIO driver support
Highbank supports SGPIO by bit-banging out the SGPIO signals over
three GPIO pins defined in the DTB. Add support for this SGPIO
functionality.

Signed-off-by: Mark Langsdorf <mark.langsdorf@calxeda.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
2013-06-06 14:05:24 -07:00
Mark Langsdorf 439d7a358f ahci: make ahci_transmit_led_message into a function pointer
Create a new ata_port_operations function pointer called
transmit_led_message and give it the default value of
ahci_transmit_led_message. This allows AHCI controllers with
non-standard LED interfaces to use the existing em_ interface.

Signed-off-by: Mark Langsdorf <mark.langsdorf@calxeda.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
2013-06-06 14:05:23 -07:00
Sergei Shtylyov 5ba59b59cb sata_rcar: fix compilation warning in sata_rcar_thaw()
When compiling the driver with gcc 4.8, it gives the following warning:

 drivers/ata/sata_rcar.c: In function `sata_rcar_thaw':
 drivers/ata/sata_rcar.c:183:2: warning: large integer implicitly truncated to unsigned type [-Woverflow]

Fix the warning by explicit cast of the 'unsigned long' value to 'u32'.

Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
2013-06-03 18:49:45 -07:00
Mark Langsdorf ddfef5de3d sata_highbank: increase retry count but shorten duration for Calxeda controller
Increase the retry count for the hard reset function to 100 but
shorten the time out period to 500 ms. See the comment for
ahci_highbank_hardreset for the reasons why those vaulues were
chosen.

Signed-off-by: Mark Langsdorf <mark.langsdorf@calxeda.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: stable@vger.kernel.org
2013-06-03 13:38:51 -07:00
Rafael J. Wysocki 45f0a85c82 PM / Runtime: Rework the "runtime idle" helper routine
The "runtime idle" helper routine, rpm_idle(), currently ignores
return values from .runtime_idle() callbacks executed by it.
However, it turns out that many subsystems use
pm_generic_runtime_idle() which checks the return value of the
driver's callback and executes pm_runtime_suspend() for the device
unless that value is not 0.  If that logic is moved to rpm_idle()
instead, pm_generic_runtime_idle() can be dropped and its users
will not need any .runtime_idle() callbacks any more.

Moreover, the PCI, SCSI, and SATA subsystems' .runtime_idle()
routines, pci_pm_runtime_idle(), scsi_runtime_idle(), and
ata_port_runtime_idle(), respectively, as well as a few drivers'
ones may be simplified if rpm_idle() calls rpm_suspend() after 0 has
been returned by the .runtime_idle() callback executed by it.

To reduce overall code bloat, make the changes described above.

Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Tested-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Kevin Hilman <khilman@linaro.org>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
2013-06-03 21:49:52 +02:00
Shane Huang fafe5c3d82 ahci: Add AMD CZ SATA device ID
To add AMD CZ SATA controller device ID of IDE mode.

[bhelgaas: drop pci_ids.h update]
Signed-off-by: Shane Huang <shane.huang@amd.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Tejun Heo <tj@kernel.org>
Cc: stable@vger.kernel.org
2013-06-03 13:02:45 -06:00
Linus Torvalds 338e33acd8 Merge branch 'for-3.10-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata
Pull libata changes from Tejun Heo:
 "Nothing too interesting.  PCI ID additions, some sata_rcar fixes and a
  fringe bug fix for DMADIR handling which shouldn't affect any device
  remotely modern."

* 'for-3.10-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
  sata_rcar: fix interrupt handling
  ahci: add an observed PCI ID for Marvell 88se9172 SATA controller
  sata_rcar: clear STOP bit in bmdma_start() method
  libata: make ata_exec_internal_sg honor DMADIR
  ata_piix: add PCI IDs for Intel BayTail
  libata: update "Maintained by:" tags
2013-06-03 17:55:09 +09:00
Jingoo Han 0a86e1c857 ata: use pci_get_drvdata()
Use the wrapper function for getting the driver data using pci_dev
instead of using dev_get_drvdata() with &pdev->dev, so we can directly
pass a struct pci_dev.  This is a purely cosmetic change.

Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
2013-06-02 22:22:03 -07:00
Sergei Shtylyov 52a2a1087b sata_rcar: fix interrupt handling
The driver's interrupt handling code is too picky in deciding whether it should
handle an interrupt or not which causes completely unneeded spurious interrupts.
Thus make sata_rcar_{ata|serr}_interrupt() *void*; add ATA status register read
to sata_rcar_ata_interrupt() to clear an unexpected ATA interrupt -- it doesn't
get cleared by writing to the SATAINTSTAT register in the interrupt mode we use.

Also, in sata_rcar_ata_interrupt() we should check SATAINTSTAT register only for
enabled interrupts and we should clear  only those interrupts  that we have read
as active first time around, because else we have  a  race and risk clearing  an
interrupt that  can  occur between read  and write of the  SATAINTSTAT  register
and never registering it...

Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: stable@vger.kernel.org
2013-06-02 00:54:45 -07:00
George Spelvin fcce9a35f8 ahci: add an observed PCI ID for Marvell 88se9172 SATA controller
A third possible PCI ID, as personally observed, and found in the
pci.ids list.

Signed-off-by: George Spelvin <linux@horizon.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
2013-05-29 10:20:35 +09:00
Sergei Shtylyov 1b20f6a9ad sata_rcar: add 'base' local variable to some functions
The 'base' field of 'struct sata_rcar_priv' is used very often
throughout the driver, so it seems worth loading it into a local
variable if it's used more than once in a function.

While at it, put some unitialized variables after intialized ones for
aesthetic reasons. :-)

Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
2013-05-28 09:18:08 +09:00
Sergei Shtylyov 8bfbeed586 sata_rcar: correct 'sata_rcar_sht'
Using ATA_BMDMA_SHT() to intialize 'sata_rcar_sht' was suboptimal as
the R-Car descriptor table transfer counter is 28 bits wide (bit 1 to
bit 28), so that the 'dma_boundary' field of 0xFFFF is just too small,
as well as the 'sg_tablesize' field of 128.  Use ATA_BASE_SHT() to
initialize 'sata_rcar_sht' instead and give proper values to the
'dma_boundary' and 'sg_tablesize' fields explicitly.

Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
2013-05-28 09:18:08 +09:00
Sergei Shtylyov 333279c82b sata_rcar: kill superfluous code in sata_rcar_bmdma_fill_sg()
I've modified sata_rcar_bmdma_fill_sg() to take care of splitting long
scatter/ gather segments due to the descriptor table transfer counter
being only 28 bits wide (bit 1 to bit 28) but that was in vain as even
if 'sata_rcar_sht' specified a correct 'dma_boundary' field, the DMA
and block layers would have split the S/G segments on the necassary
boundaries. Since the driver uses ATA_BMDMA_SHT() to initilaize
'sata_rcar_sht', the boundary is much smaller, only 0xFFFF, so the
code I've added is even more useless, and it's better to just remove
it.

Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
2013-05-28 09:18:08 +09:00
Simon Horman 5c23341ff6 libata: do not limit R-Car SATA driver to shmobile
The motivation for this is to allow the driver to be
used with the r8a7790 SoC.

I believe that rather than adding another SoC to the list of allowed SoCs
it is better to simply remove the dependency of the driver on shmobile all
together.

Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Tejun Heo <tj@kernel.org>
2013-05-24 11:33:40 +09:00
Jingoo Han d89995db5f ata: use platform_{get,set}_drvdata()
Use the wrapper functions for getting and setting the driver data using
platform_device instead of using dev_{get,set}_drvdata() with &pdev->dev,
so we can directly pass a struct platform_device.

Also, unnecessary dev_set_drvdata() is removed, because the driver core
clears the driver data to NULL after device_release or on probe failure.

Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
2013-05-24 10:26:13 +09:00
Alexander Gordeev b29900e625 AHCI: Make distinct names for ports in /proc/interrupts
Currently all interrupts assigned to AHCI ports show up in
'/proc/interrupts' as 'ahci'. This fix adds port numbers as
suffixes and hence makes the descriptions distinct.

Reported-by: Jan Beulich <JBeulich@suse.com>
Signed-off-by: Alexander Gordeev <agordeev@redhat.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
2013-05-22 08:53:48 +09:00
Sergei Shtylyov df7e131f63 sata_rcar: clear STOP bit in bmdma_start() method
Iff bmdma_setup() has to stop a DMA transfer before starting a new
one, then the STOP bit in the ATAPI_CONTROL1 register will remain set
(it's only cleared when setting the START bit to 1) and then
bmdma_start() method will set both START and STOP bits simultaneously
which should abort the transfer being just started.  Avoid that by
explicitly clearing the STOP bit in bmdma_start() method (in this case
it will be ignored on write).

Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: stable@vger.kernel.org
2013-05-22 08:39:20 +09:00
Vincent Pelletier 966fbe193f libata: Add atapi_dmadir force flag
Some device require DMADIR to be enabled, but are not detected as such
by atapi_id_dmadir.  One such example is "Asus Serillel 2"
SATA-host-to-PATA-device bridge: the bridge itself requires DMADIR,
even if the bridged device does not.

As atapi_dmadir module parameter can cause problems with some devices
(as per Tejun Heo's memory), enabling it globally may not be possible
depending on the hardware.

This patch adds atapi_dmadir in the form of a "force" horkage value,
allowing global, per-bus and per-device control.

Signed-off-by: Vincent Pelletier <plr.vincent@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
2013-05-22 08:34:34 +09:00
Vincent Pelletier e771451c0a libata: make ata_exec_internal_sg honor DMADIR
libata honors DMADIR for regular commands, but not for internal commands
used (among other) during device initialisation.

This makes SATA-host-to-PATA-device bridges based on Silicon Image SiL3611
(such as "Abit Serillel 2") end up disabled when used with an ATAPI device
after a few tries.

Log output of the bridge being hot-plugged with an ATAPI drive:

  [ 9631.212901] ata1: exception Emask 0x10 SAct 0x0 SErr 0x40c0000 action 0xe frozen
  [ 9631.212913] ata1: irq_stat 0x00000040, connection status changed
  [ 9631.212923] ata1: SError: { CommWake 10B8B DevExch }
  [ 9631.212939] ata1: hard resetting link
  [ 9632.104962] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
  [ 9632.106393] ata1.00: ATAPI: PIONEER DVD-RW  DVR-115, 1.06, max UDMA/33
  [ 9632.106407] ata1.00: applying bridge limits
  [ 9632.108151] ata1.00: configured for UDMA/33
  [ 9637.105303] ata1.00: qc timeout (cmd 0xa0)
  [ 9637.105324] ata1.00: failed to clear UNIT ATTENTION (err_mask=0x5)
  [ 9637.105335] ata1: hard resetting link
  [ 9638.044599] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
  [ 9638.047878] ata1.00: configured for UDMA/33
  [ 9643.044933] ata1.00: qc timeout (cmd 0xa0)
  [ 9643.044953] ata1.00: failed to clear UNIT ATTENTION (err_mask=0x5)
  [ 9643.044963] ata1: limiting SATA link speed to 1.5 Gbps
  [ 9643.044971] ata1.00: limiting speed to UDMA/33:PIO3
  [ 9643.044979] ata1: hard resetting link
  [ 9643.984225] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
  [ 9643.987471] ata1.00: configured for UDMA/33
  [ 9648.984591] ata1.00: qc timeout (cmd 0xa0)
  [ 9648.984612] ata1.00: failed to clear UNIT ATTENTION (err_mask=0x5)
  [ 9648.984619] ata1.00: disabled
  [ 9649.000593] ata1: hard resetting link
  [ 9649.939902] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
  [ 9649.955864] ata1: EH complete

With this patch, the drive enumerates correctly when libata is loaded with
atapi_dmadir=1:

  [ 9891.810863] ata1: exception Emask 0x10 SAct 0x0 SErr 0x40c0000 action 0xe frozen
  [ 9891.810874] ata1: irq_stat 0x00000040, connection status changed
  [ 9891.810884] ata1: SError: { CommWake 10B8B DevExch }
  [ 9891.810900] ata1: hard resetting link
  [ 9892.762105] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
  [ 9892.763544] ata1.00: ATAPI: PIONEER DVD-RW  DVR-115, 1.06, max UDMA/33, DMADIR
  [ 9892.763558] ata1.00: applying bridge limits
  [ 9892.765393] ata1.00: configured for UDMA/33
  [ 9892.786063] ata1: EH complete
  [ 9892.792062] scsi 0:0:0:0: CD-ROM            PIONEER  DVD-RW  DVR-115  1.06 PQ: 0 ANSI: 5
  [ 9892.798455] sr2: scsi3-mmc drive: 12x/12x writer dvd-ram cd/rw xa/form2 cdda tray
  [ 9892.798837] sr 0:0:0:0: Attached scsi CD-ROM sr2
  [ 9892.799109] sr 0:0:0:0: Attached scsi generic sg6 type 5

Based on a patch by Csaba Halász <csaba.halasz@gmail.com> on linux-ide:
http://marc.info/?l=linux-ide&m=136121147832295&w=2

tj: minor formatting changes.

Signed-off-by: Vincent Pelletier <plr.vincent@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: stable@vger.kernel.org
2013-05-22 08:31:48 +09:00
Chew, Chiau Ee fca8c90d51 ata_piix: add PCI IDs for Intel BayTail
Adds IDE-mode SATA Device IDs for the Intel BayTrail platform.

Signed-off-by: Chew, Chiau Ee <chiau.ee.chew@intel.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: stable@vger.kernel.org
2013-05-16 11:06:29 -07:00
David Milburn e628dc999e libata: export ata_port port_no attribute via /sys
While registering host controller track port number based upon number
of ports available on the controller, export port_no attribute through
/sys. This patch is needed by udev for composing persistent links in
/dev/disk/by-path.

/sys/devices/pci0000:00/0000:00:1f.2/ata8/ata_port/ata8
total 0
lrwxrwxrwx. 1 root root    0 Mar  6 12:43 device -> ../../../ata8
-r--r--r--. 1 root root 4096 Mar  6 12:43 idle_irq
-r--r--r--. 1 root root 4096 Mar  6 12:43 nr_pmp_links
-r--r--r--. 1 root root 4096 Mar  6 12:43 port_no
drwxr-xr-x. 2 root root    0 Mar  6 12:42 power
lrwxrwxrwx. 1 root root    0 Mar  6 12:41 subsystem -> ../../../../../../class/ata_port
-rw-r--r--. 1 root root 4096 Mar  6 12:40 uevent
1

Signed-off-by: David Milburn <dmilburn@redhat.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
2013-05-14 11:44:07 -07:00
Tejun Heo 8c3d3d4b12 libata: update "Maintained by:" tags
Jeff moved on to a greener pasture.

 s/Maintained by: Jeff Garzik/Maintained by: Tejun Heo/g

Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Jeff Garzik <jgarzik@pobox.com>
2013-05-14 11:13:04 -07:00
Wolfram Sang 29589f06d2 drivers/ata: don't check resource with devm_ioremap_resource
devm_ioremap_resource does sanity checks on the given resource. No need to
duplicate this in the driver.

Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2013-05-12 15:19:46 +02:00
Linus Torvalds 1bf25e78af ARM: arm-soc: late cleanups
These are cleanups and smaller changes that either depend on earlier
 feature branches or came in late during the development cycle.
 We normally try to get all cleanups early, so these are the exceptions:
 
 - A follow-up on the clocksource reworks, hopefully the last time
   we need to merge clocksource subsystem changes through arm-soc.
   A first set of patches was part of the original 3.10 arm-soc cleanup
   series because of interdependencies with timer drivers now moved out
   of arch/arm.
 
 - Migrating the SPEAr13xx platform away from using auxdata for DMA
   channel descriptions towards using information in device tree,
   based on the earlier SPEAr multiplatform series
 
 - A few follow-ups on the Atmel SAMA5 support and other changes
   for Atmel at91 based on the larger at91 reworks.
 
 - Moving the armada irqchip implementation to drivers/irqchip
 
 - Several OMAP cleanups following up on the larger series already
   merged in 3.10.
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1.4.12 (GNU/Linux)
 
 iQIVAwUAUYj5U2CrR//JCVInAQLNIRAAvsCtYOmXTxkRBxdtNEUUbkEjx71Se7q0
 h9PR8vqlkbYwONkJ8a6j8pKq/WJDmLpHQWg/moBsvlGc6uEVBPBFhCWHs1+yGUzX
 GhnJOaIKh3+651hIoXccS+/YZ16e1EAzdCM7+1QegPTldsRGkTOiwXgmR51kmPrz
 6cZ8P5MFqMrWIy4XqWhOBbMDCY/An05IHMpniGIamUg2/uB921Z0wNFvDrnsg97u
 DsVEwimyCJ0j7aO4TH+fkvsjoGWnIhxPtpaIm8iff6TPRI49deRb3zYpnIONm+oG
 /cQrRf3BNW+aiTuRCTEjdBNGtcrYgN6CLWWjzgMhv1itSlX8swBcOhuNJRCGNQRI
 v3wL4aEBxUpPGGL8erc2GIW7pe29YC2UEYI2z1X/5MEzYO589zkkG2k+/3HQVUwp
 dnYpQxhjRMvh4mcodBJFRjzH1Z7agKUwtoKalAHRRH7r5gJDkpL3zLoMhYPTG5IZ
 OwU+aYf+dDxh2kKW0zs8a/qL97UTHjlTRUC9LPoumvJ7LlKeDfzEn7DHUm2gggiu
 dO9ye/NF/xEXoDXTl0Qp2wJ6/sbPSLyCYCIMdP/gJjWUiDDqqZ0VRaKL7vE/JWrd
 NJ7k5yunX8/kRgfqgRFLDdFnPj1JeYHlmexsq4l9TPbPstoIcbw8u1v9sr8aZF+Z
 agh9u4e7QU8=
 =HWfp
 -----END PGP SIGNATURE-----

Merge tag 'cleanup-for-linus-2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc

Pull ARM SoC late cleanups from Arnd Bergmann:
 "These are cleanups and smaller changes that either depend on earlier
  feature branches or came in late during the development cycle.  We
  normally try to get all cleanups early, so these are the exceptions:

   - A follow-up on the clocksource reworks, hopefully the last time we
     need to merge clocksource subsystem changes through arm-soc.

     A first set of patches was part of the original 3.10 arm-soc
     cleanup series because of interdependencies with timer drivers now
     moved out of arch/arm.

   - Migrating the SPEAr13xx platform away from using auxdata for DMA
     channel descriptions towards using information in device tree,
     based on the earlier SPEAr multiplatform series

   - A few follow-ups on the Atmel SAMA5 support and other changes for
     Atmel at91 based on the larger at91 reworks.

   - Moving the armada irqchip implementation to drivers/irqchip

   - Several OMAP cleanups following up on the larger series already
     merged in 3.10."

* tag 'cleanup-for-linus-2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (50 commits)
  ARM: OMAP4: change the device names in usb_bind_phy
  ARM: OMAP2+: Fix mismerge for timer.c between ff931c82 and da4a686a
  ARM: SPEAr: conditionalize SMP code
  ARM: arch_timer: Silence debug preempt warnings
  ARM: OMAP: remove unused variable
  serial: amba-pl011: fix !CONFIG_DMA_ENGINE case
  ata: arasan: remove the need for platform_data
  ARM: at91/sama5d34ek.dts: remove not needed compatibility string
  ARM: at91: dts: add MCI DMA support
  ARM: at91: dts: add i2c dma support
  ARM: at91: dts: set #dma-cells to the correct value
  ARM: at91: suspend both memory controllers on at91sam9263
  irqchip: armada-370-xp: slightly cleanup irq controller driver
  irqchip: armada-370-xp: move IRQ handler to avoid forward declaration
  irqchip: move IRQ driver for Armada 370/XP
  ARM: mvebu: move L2 cache initialization in init_early()
  devtree: add binding documentation for sp804
  ARM: integrator-cp: convert use CLKSRC_OF for timer init
  ARM: versatile: use OF init for sp804 timer
  ARM: versatile: add versatile dtbs to dtbs target
  ...
2013-05-07 11:22:14 -07:00
Linus Torvalds 20b4fb4852 Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull VFS updates from Al Viro,

Misc cleanups all over the place, mainly wrt /proc interfaces (switch
create_proc_entry to proc_create(), get rid of the deprecated
create_proc_read_entry() in favor of using proc_create_data() and
seq_file etc).

7kloc removed.

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (204 commits)
  don't bother with deferred freeing of fdtables
  proc: Move non-public stuff from linux/proc_fs.h to fs/proc/internal.h
  proc: Make the PROC_I() and PDE() macros internal to procfs
  proc: Supply a function to remove a proc entry by PDE
  take cgroup_open() and cpuset_open() to fs/proc/base.c
  ppc: Clean up scanlog
  ppc: Clean up rtas_flash driver somewhat
  hostap: proc: Use remove_proc_subtree()
  drm: proc: Use remove_proc_subtree()
  drm: proc: Use minor->index to label things, not PDE->name
  drm: Constify drm_proc_list[]
  zoran: Don't print proc_dir_entry data in debug
  reiserfs: Don't access the proc_dir_entry in r_open(), r_start() r_show()
  proc: Supply an accessor for getting the data from a PDE's parent
  airo: Use remove_proc_subtree()
  rtl8192u: Don't need to save device proc dir PDE
  rtl8187se: Use a dir under /proc/net/r8180/
  proc: Add proc_mkdir_data()
  proc: Move some bits from linux/proc_fs.h to linux/{of.h,signal.h,tty.h}
  proc: Move PDE_NET() to fs/proc/proc_net.c
  ...
2013-05-01 17:51:54 -07:00
Linus Torvalds 50528fabeb 1) More ACPI fixes, cleanups
2) Minor cleanups for sata_highbank, pata_at32, pata_octeon_cf,
    sata_rcar
 
 3) pata_legacy: small bug found in opti chipset code (untested fix,
    due to ancient h/w)
 
 4) sata_fsl: RX water mark config knob, some h/w needs it
 
 5) pata_imx: cleanups, DeviceTree support
 
 6) SCSI<->ATA translator: properly export translator version,
    not device firmware version
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1.4.13 (GNU/Linux)
 
 iQIVAwUAUYBD4SWzCDIBeCsvAQLMKQ/+II9KX8ztaPIil+mm/Uzg47J5p7AUjG6b
 hk/jnwJTn1M+yvyTe1D1D9LM+9j12XTOCT3Q3u/W7CSFdOc+nMLbI6upty/rHs6L
 5N2OvTAA2r4k0CmHe/pXzV0YMkWQE48KQh4S/GZV1wQOt7l4fcfqcx9sEWFPh1dc
 4uud+nfeF9P9JG8W6in1hzRqFV++qY/jo7+NQeED24JgjpwpoB/PiJpg6JE4F9/4
 WUxWlHQkJyiCar7gCnJGSBAaN3D8t19ptdSx375spzgi1NQZV2AfyuliX1p0vEQo
 Z8q+3hY6m2kNtj6ZVLmIJIj/k4LUbU4E9hbPV8eIGLeTU46GZVkqZ6th+amCJw40
 iHsAyDXuzgne8kvkM9tvzPALauAurbt8PPZFh7aPP05pjI4FXBEO+BMe78TlnevQ
 F+2VBhIh6C9D7Mo9BIOiMB6sU0mpwqtfH3xaaz39U+cs+xKPa9Ws2lyOVZXGEwTV
 WaChOpUrN9NNeH9EN3GFA6KY4ovkfYdmc7ahYIBy+xyuh2AiLcsZmyqmEhMyCAQ8
 16y0yIoYQNQnC9QooezsuCT9WUqNA0YI+ICQrESX+kviN/wO5LamKN1xI5k/QHR2
 6eFuIPat8acHhpa01obOo1HOdvbSuO+uXOtiBToPf+S+d9NFMvVw/j4RkHkTV+Fv
 xVTbSvP5+TQ=
 =kLMT
 -----END PGP SIGNATURE-----

Merge tag 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev

Pull libata update from Jeff Garzik:

 - More ACPI fixes, cleanups

 - Minor cleanups for sata_highbank, pata_at32, pata_octeon_cf,
   sata_rcar

 - pata_legacy: small bug found in opti chipset code (untested fix, due
   to ancient h/w)

 - sata_fsl: RX water mark config knob, some h/w needs it

 - pata_imx: cleanups, DeviceTree support

 - SCSI<->ATA translator: properly export translator version, not device
   firmware version

* tag 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
  sata_highbank: Rename proc_name to the module name
  ACPI/libata: Restore libata.noacpi support
  [libata] acpi: make ata_ap_acpi_handle not block
  [libata] SCSI: really use SATL version in VPD
  pata_imx: add devicetree support
  pata_imx: use void __iomem * for regs
  pata_imx: cleanup error path
  pata_imx: Use devm_clk_get
  sata_rcar: Convert to devm_ioremap_resource()
  fsl/sata: create a sysfs entry for rx water mark
  libata-acpi: remove redundent code for power resource handling
  sata_highbank: make ahci_highbank_pm_ops static
  pata_octeon_cf: Use resource_size function
  pata_legacy: bogus clock in opti82c46x_set_piomode()
  pata_at32: use module_platform_driver_probe()
2013-04-30 16:13:36 -07:00
Robert Richter 2cc1144a31 sata_highbank: Rename proc_name to the module name
mkinitrd looks at /sys/class/scsi_host/host$hostnum/proc_name to find
the module name of a disk driver. Current name is "highbank-ahci" but
the module is "sata_highbank". Rename it to match the module name.

Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Alexander Graf <agraf@suse.de>
Cc: <stable@vger.kernel.org> v3.7..
Signed-off-by: Robert Richter <robert.richter@calxeda.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2013-04-30 18:02:56 -04:00
Lv Zheng 19ccee765f ACPI/libata: Restore libata.noacpi support
This patch restores libata.noacpi support to libata-acpi.c.
There are broken optional control methods for ATA controller devices in the
real world.  The libata.noacpi has been used for a long time as a
workaround to deal with issues caused by the broken ASL codes.
1. The "noacpi" option is introduced by the following commit:
   commit 11ef697b37
   Date: Thu, 28 Sep 2006 11:29:01 -0700
   Subject: libata: ACPI and _GTF support
2. The "noacpi" option is renamed to "libata_noacpi" by the following
   commit:
   commit d7d0dad62a
   Date: Wed, 28 Mar 2007 01:57:37 -0400
   Subject: [libata] Disable ACPI by default; fix namespace problems
3. Some of its logics are changed over time - becomes relying on the
   "acpi_handle" bound to the ATA devices since this commit:
   commit fafbae87db
   Date: Tue, 15 May 2007 03:28:16 +0900
   Subject: libata-acpi: implement ata_acpi_associate()
4. The option is deleted by the following commit:
   commit 30dcf76acc
   Date: Mon, 25 Jun 2012 16:13:04 +0800
   Subject: libata: migrate ACPI code over to new bindings
But the libata.noacpi setup is still left in the kernel without codes to
implement it.  So the deletion introduces a regression to the Linux.
This patch disables ATA_ACPI support at runtime by stopping acpi binding
on the ATA devices to fix this regression.
This patch is tested by booting a SATA x86-64 kernel or a PATA x86 kernel
with or without "libata.noacpi=1" kernel command line argument.

Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Aaron Lu <aaron.lu@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2013-04-30 18:02:53 -04:00
Aaron Lu d66af4df08 [libata] acpi: make ata_ap_acpi_handle not block
Since commit 30dcf76acc, ata_ap_acpi_handle will always do a namespace
walk, which requires acquiring an acpi namespace mutex. This made it
impossible to be used when calling path has held a spinlock.

For example, it can occur in the following code path for pata_acpi:
ata_scsi_queuecmd (ap->lock is acquired)
  __ata_scsi_queuecmd
    ata_scsi_translate
      ata_qc_issue
        pacpi_qc_issue
          ata_acpi_stm
            ata_ap_acpi_handle
              acpi_get_child
                acpi_walk_namespace
                  acpi_ut_acquire_mutex (acquire mutex while holding lock)
This caused scheduling while atomic bug, as reported in bug #56781.

Actually, ata_ap_acpi_handle doesn't have to walk the namespace every
time it is called, it can simply return the bound acpi handle on the
corresponding SCSI host. The reason previously it is not done this way
is, ata_ap_acpi_handle is used in the binding function
ata_acpi_bind_host by ata_acpi_gtm when the handle is not bound to the
SCSI host yet. Since we already have the ATA port's handle in its
binding function, we can simply use it instead of calling
ata_ap_acpi_handle there. So introduce a new function __ata_acpi_gtm,
where it will receive an acpi handle param in addition to the ATA port
which is solely used for debug statement. With this change, we can make
ata_ap_acpi_handle simply return the bound handle for SCSI host instead
of walking the acpi namespace now.

Buglink: https://bugzilla.kernel.org/show_bug.cgi?id=56781
Reported-and-tested-by: <kenzopl@o2.pl>
Cc: <stable@vger.kernel.org>
Signed-off-by: Aaron Lu <aaron.lu@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2013-04-30 18:02:45 -04:00