There are 1 action and 1 qdisc that may process IPv4 TCP GSO packets
and access iph->tot_len, replace them with skb_ip_totlen() and
iph_totlen() accordingly.
Note that we don't need to replace the one in tcf_csum_ipv4(), as it
will return for TCP GSO packets in tcf_csum_ipv4_tcp().
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When the default qdisc is cake, if the qdisc of dev_queue fails to be
inited during mqprio_init(), cake_reset() is invoked to clear
resources. In this case, the tins is NULL, and it will cause gpf issue.
The process is as follows:
qdisc_create_dflt()
cake_init()
q->tins = kvcalloc(...) --->failed, q->tins is NULL
...
qdisc_put()
...
cake_reset()
...
cake_dequeue_one()
b = &q->tins[...] --->q->tins is NULL
The following is the Call Trace information:
general protection fault, probably for non-canonical address
0xdffffc0000000000: 0000 [#1] PREEMPT SMP KASAN
KASAN: null-ptr-deref in range [0x0000000000000000-0x0000000000000007]
RIP: 0010:cake_dequeue_one+0xc9/0x3c0
Call Trace:
<TASK>
cake_reset+0xb1/0x140
qdisc_reset+0xed/0x6f0
qdisc_destroy+0x82/0x4c0
qdisc_put+0x9e/0xb0
qdisc_create_dflt+0x2c3/0x4a0
mqprio_init+0xa71/0x1760
qdisc_create+0x3eb/0x1000
tc_modify_qdisc+0x408/0x1720
rtnetlink_rcv_msg+0x38e/0xac0
netlink_rcv_skb+0x12d/0x3a0
netlink_unicast+0x4a2/0x740
netlink_sendmsg+0x826/0xcc0
sock_sendmsg+0xc5/0x100
____sys_sendmsg+0x583/0x690
___sys_sendmsg+0xe8/0x160
__sys_sendmsg+0xbf/0x160
do_syscall_64+0x35/0x80
entry_SYSCALL_64_after_hwframe+0x46/0xb0
RIP: 0033:0x7f89e5122d04
</TASK>
Fixes: 046f6fd5da ("sched: Add Common Applications Kept Enhanced (cake) qdisc")
Signed-off-by: Zhengchao Shao <shaozhengchao@huawei.com>
Acked-by: Toke Høiland-Jørgensen <toke@toke.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
The prandom_u32() function has been a deprecated inline wrapper around
get_random_u32() for several releases now, and compiles down to the
exact same code. Replace the deprecated wrapper with a direct call to
the real function. The same also applies to get_random_int(), which is
just a wrapper around get_random_u32(). This was done as a basic find
and replace.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Yury Norov <yury.norov@gmail.com>
Reviewed-by: Jan Kara <jack@suse.cz> # for ext4
Acked-by: Toke Høiland-Jørgensen <toke@toke.dk> # for sch_cake
Acked-by: Chuck Lever <chuck.lever@oracle.com> # for nfsd
Acked-by: Jakub Kicinski <kuba@kernel.org>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com> # for thunderbolt
Acked-by: Darrick J. Wong <djwong@kernel.org> # for xfs
Acked-by: Helge Deller <deller@gmx.de> # for parisc
Acked-by: Heiko Carstens <hca@linux.ibm.com> # for s390
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
use tc_qdisc_stats_dump() in qdisc.
Signed-off-by: Zhengchao Shao <shaozhengchao@huawei.com>
Reviewed-by: Victor Nogueira <victor@mojatatu.com>
Tested-by: Victor Nogueira <victor@mojatatu.com>
Acked-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Currently, the change function can be called by two ways. The one way is
that qdisc_change() will call it. Before calling change function,
qdisc_change() ensures tca[TCA_OPTIONS] is not empty. The other way is
that .init() will call it. The opt parameter is also checked before
calling change function in .init(). Therefore, it's no need to check the
input parameter opt in change function.
Signed-off-by: Zhengchao Shao <shaozhengchao@huawei.com>
Acked-by: Toke Høiland-Jørgensen <toke@toke.dk>
Link: https://lore.kernel.org/r/20220829071219.208646-1-shaozhengchao@huawei.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Documentation incorrectly stated that CS1 is equivalent to LE for
diffserv8. But when LE was added to the table, CS1 was pushed into tin
1, leaving only LE in tin 0.
Also "TOS1" no longer exists, as that is the same codepoint as LE.
Make other tweaks properly distinguishing codepoints from classes and
putting current Diffserve codepoints ahead of legacy ones.
Signed-off-by: Kevin Bracey <kevin@bracey.fi>
Acked-by: Toke Høiland-Jørgensen <toke@toke.dk>
Link: https://lore.kernel.org/r/20220106215637.3132391-1-kevin@bracey.fi
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When adding support for using the skb->hash value as the flow hash in CAKE,
I accidentally introduced a logic error that broke the host-only isolation
modes of CAKE (srchost and dsthost keywords). Specifically, the flow_hash
variable should stay initialised to 0 in cake_hash() in pure host-based
hashing mode. Add a check for this before using the skb->hash value as
flow_hash.
Fixes: b0c19ed608 ("sch_cake: Take advantage of skb->hash where appropriate")
Reported-by: Pete Heist <pete@heistp.net>
Tested-by: Pete Heist <pete@heistp.net>
Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
currently, only 'ingress' and 'clsact ingress' qdiscs store the tc 'chain
id' in the skb extension. However, userspace programs (like ovs) are able
to setup egress rules, and datapath gets confused in case it doesn't find
the 'chain id' for a packet that's "recirculated" by tc.
Change tcf_classify() to have the same semantic as tcf_classify_ingress()
so that a single function can be called in ingress / egress, using the tc
ingress / egress block respectively.
Suggested-by: Alaa Hleilel <alaa@nvidia.com>
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Reviewed-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit b8392808eb ("sch_cake: add RFC 8622 LE PHB support to CAKE
diffserv handling") added the LE mark to the Bulk tin. Update the
comments to reflect the change.
Signed-off-by: Tyson Moore <tyson@tyson.me>
Acked-by: Toke Høiland-Jørgensen <toke@toke.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
The TCP option parser in cake qdisc (cake_get_tcpopt and
cake_tcph_may_drop) could read one byte out of bounds. When the length
is 1, the execution flow gets into the loop, reads one byte of the
opcode, and if the opcode is neither TCPOPT_EOL nor TCPOPT_NOP, it reads
one more byte, which exceeds the length of 1.
This fix is inspired by commit 9609dad263 ("ipv4: tcp_input: fix stack
out of bounds when parsing TCP options.").
v2 changes:
Added doff validation in cake_get_tcphdr to avoid parsing garbage as TCP
header. Although it wasn't strictly an out-of-bounds access (memory was
allocated), garbage values could be read where CAKE expected the TCP
header if doff was smaller than 5.
Cc: Young Xiao <92siuyang@gmail.com>
Fixes: 8b7138814f ("sch_cake: Add optional ACK filter")
Signed-off-by: Maxim Mikityanskiy <maximmi@nvidia.com>
Acked-by: Toke Høiland-Jørgensen <toke@toke.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking updates from David Miller:
1) Support 6Ghz band in ath11k driver, from Rajkumar Manoharan.
2) Support UDP segmentation in code TSO code, from Eric Dumazet.
3) Allow flashing different flash images in cxgb4 driver, from Vishal
Kulkarni.
4) Add drop frames counter and flow status to tc flower offloading,
from Po Liu.
5) Support n-tuple filters in cxgb4, from Vishal Kulkarni.
6) Various new indirect call avoidance, from Eric Dumazet and Brian
Vazquez.
7) Fix BPF verifier failures on 32-bit pointer arithmetic, from
Yonghong Song.
8) Support querying and setting hardware address of a port function via
devlink, use this in mlx5, from Parav Pandit.
9) Support hw ipsec offload on bonding slaves, from Jarod Wilson.
10) Switch qca8k driver over to phylink, from Jonathan McDowell.
11) In bpftool, show list of processes holding BPF FD references to
maps, programs, links, and btf objects. From Andrii Nakryiko.
12) Several conversions over to generic power management, from Vaibhav
Gupta.
13) Add support for SO_KEEPALIVE et al. to bpf_setsockopt(), from Dmitry
Yakunin.
14) Various https url conversions, from Alexander A. Klimov.
15) Timestamping and PHC support for mscc PHY driver, from Antoine
Tenart.
16) Support bpf iterating over tcp and udp sockets, from Yonghong Song.
17) Support 5GBASE-T i40e NICs, from Aleksandr Loktionov.
18) Add kTLS RX HW offload support to mlx5e, from Tariq Toukan.
19) Fix the ->ndo_start_xmit() return type to be netdev_tx_t in several
drivers. From Luc Van Oostenryck.
20) XDP support for xen-netfront, from Denis Kirjanov.
21) Support receive buffer autotuning in MPTCP, from Florian Westphal.
22) Support EF100 chip in sfc driver, from Edward Cree.
23) Add XDP support to mvpp2 driver, from Matteo Croce.
24) Support MPTCP in sock_diag, from Paolo Abeni.
25) Commonize UDP tunnel offloading code by creating udp_tunnel_nic
infrastructure, from Jakub Kicinski.
26) Several pci_ --> dma_ API conversions, from Christophe JAILLET.
27) Add FLOW_ACTION_POLICE support to mlxsw, from Ido Schimmel.
28) Add SK_LOOKUP bpf program type, from Jakub Sitnicki.
29) Refactor a lot of networking socket option handling code in order to
avoid set_fs() calls, from Christoph Hellwig.
30) Add rfc4884 support to icmp code, from Willem de Bruijn.
31) Support TBF offload in dpaa2-eth driver, from Ioana Ciornei.
32) Support XDP_REDIRECT in qede driver, from Alexander Lobakin.
33) Support PCI relaxed ordering in mlx5 driver, from Aya Levin.
34) Support TCP syncookies in MPTCP, from Flowian Westphal.
35) Fix several tricky cases of PMTU handling wrt. briding, from Stefano
Brivio.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (2056 commits)
net: thunderx: initialize VF's mailbox mutex before first usage
usb: hso: remove bogus check for EINPROGRESS
usb: hso: no complaint about kmalloc failure
hso: fix bailout in error case of probe
ip_tunnel_core: Fix build for archs without _HAVE_ARCH_IPV6_CSUM
selftests/net: relax cpu affinity requirement in msg_zerocopy test
mptcp: be careful on subflow creation
selftests: rtnetlink: make kci_test_encap() return sub-test result
selftests: rtnetlink: correct the final return value for the test
net: dsa: sja1105: use detected device id instead of DT one on mismatch
tipc: set ub->ifindex for local ipv6 address
ipv6: add ipv6_dev_find()
net: openvswitch: silence suspicious RCU usage warning
Revert "vxlan: fix tos value before xmit"
ptp: only allow phase values lower than 1 period
farsync: switch from 'pci_' to 'dma_' API
wan: wanxl: switch from 'pci_' to 'dma_' API
hv_netvsc: do not use VF device if link is down
dpaa2-eth: Fix passing zero to 'PTR_ERR' warning
net: macb: Properly handle phylink on at91sam9x
...
Using uninitialized_var() is dangerous as it papers over real bugs[1]
(or can in the future), and suppresses unrelated compiler warnings
(e.g. "unused variable"). If the compiler thinks it is uninitialized,
either simply initialize the variable or make compiler changes.
In preparation for removing[2] the[3] macro[4], remove all remaining
needless uses with the following script:
git grep '\buninitialized_var\b' | cut -d: -f1 | sort -u | \
xargs perl -pi -e \
's/\buninitialized_var\(([^\)]+)\)/\1/g;
s:\s*/\* (GCC be quiet|to make compiler happy) \*/$::g;'
drivers/video/fbdev/riva/riva_hw.c was manually tweaked to avoid
pathological white-space.
No outstanding warnings were found building allmodconfig with GCC 9.3.0
for x86_64, i386, arm64, arm, powerpc, powerpc64le, s390x, mips, sparc64,
alpha, and m68k.
[1] https://lore.kernel.org/lkml/20200603174714.192027-1-glider@google.com/
[2] https://lore.kernel.org/lkml/CA+55aFw+Vbj0i=1TGqCR5vQkCzWJ0QxK6CernOU6eedsudAixw@mail.gmail.com/
[3] https://lore.kernel.org/lkml/CA+55aFwgbgqhbp1fkxvRKEpzyR5J8n1vKT1VZdz9knmPuXhOeg@mail.gmail.com/
[4] https://lore.kernel.org/lkml/CA+55aFz2500WfbKXAx8s67wrm9=yVJu65TpLgN_ybYNv0VEOKA@mail.gmail.com/
Reviewed-by: Leon Romanovsky <leonro@mellanox.com> # drivers/infiniband and mlx4/mlx5
Acked-by: Jason Gunthorpe <jgg@mellanox.com> # IB
Acked-by: Kalle Valo <kvalo@codeaurora.org> # wireless drivers
Reviewed-by: Chao Yu <yuchao0@huawei.com> # erofs
Signed-off-by: Kees Cook <keescook@chromium.org>
There are a couple of places in net/sched/ that check skb->protocol and act
on the value there. However, in the presence of VLAN tags, the value stored
in skb->protocol can be inconsistent based on whether VLAN acceleration is
enabled. The commit quoted in the Fixes tag below fixed the users of
skb->protocol to use a helper that will always see the VLAN ethertype.
However, most of the callers don't actually handle the VLAN ethertype, but
expect to find the IP header type in the protocol field. This means that
things like changing the ECN field, or parsing diffserv values, stops
working if there's a VLAN tag, or if there are multiple nested VLAN
tags (QinQ).
To fix this, change the helper to take an argument that indicates whether
the caller wants to skip the VLAN tags or not. When skipping VLAN tags, we
make sure to skip all of them, so behaviour is consistent even in QinQ
mode.
To make the helper usable from the ECN code, move it to if_vlan.h instead
of pkt_sched.h.
v3:
- Remove empty lines
- Move vlan variable definitions inside loop in skb_protocol()
- Also use skb_protocol() helper in IP{,6}_ECN_decapsulate() and
bpf_skb_ecn_set_ce()
v2:
- Use eth_type_vlan() helper in skb_protocol()
- Also fix code that reads skb->protocol directly
- Change a couple of 'if/else if' statements to switch constructs to avoid
calling the helper twice
Reported-by: Ilya Ponetayev <i.ponetaev@ndmsystems.com>
Fixes: d8b9605d26 ("net: sched: fix skb->protocol use in case of accelerated vlan path")
Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A following patch introduces qevents, points in qdisc algorithm where
packet can be processed by user-defined filters. Should this processing
lead to a situation where a new packet is to be enqueued on the same port,
holding the root lock would lead to deadlocks. To solve the issue, qevent
handler needs to unlock and relock the root lock when necessary.
To that end, add the root lock argument to the qdisc op enqueue, and
propagate throughout.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Minor overlapping changes in xfrm_device.c, between the double
ESP trailing bug fix setting the XFRM_INIT flag and the changes
in net-next preparing for bonding encryption support.
Signed-off-by: David S. Miller <davem@davemloft.net>
Change tin mapping on diffserv3, 4 & 8 for LE PHB support, in essence
making LE a member of the Bulk tin.
Bulk has the least priority and minimum of 1/16th total bandwidth in the
face of higher priority traffic.
NB: Diffserv 3 & 4 swap tin 0 & 1 priorities from the default order as
found in diffserv8, in case anyone is wondering why it looks a bit odd.
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
[ reword commit message slightly ]
Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I spotted a few nits when comparing the in-tree version of sch_cake with
the out-of-tree one: A redundant error variable declaration shadowing an
outer declaration, and an indentation alignment issue. Fix both of these.
Fixes: 046f6fd5da ("sched: Add Common Applications Kept Enhanced (cake) qdisc")
Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As a further optimisation of the diffserv parsing codepath, we can skip it
entirely if CAKE is configured to neither use diffserv-based
classification, nor to zero out the diffserv bits.
Fixes: c87b4ecdbe ("sch_cake: Make sure we can write the IP header before changing DSCP bits")
Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
cake_handle_diffserv() tries to linearize mac and network header parts of
skb and to make it writable unconditionally. In some cases it leads to full
skb reallocation, which reduces throughput and increases CPU load. Some
measurements of IPv4 forward + NAPT on MIPS router with 580 MHz single-core
CPU was conducted. It appears that on kernel 4.9 skb_try_make_writable()
reallocates skb, if skb was allocated in ethernet driver via so-called
'build skb' method from page cache (it was discovered by strange increase
of kmalloc-2048 slab at first).
Obtain DSCP value via read-only skb_header_pointer() call, and leave
linearization only for DSCP bleaching or ECN CE setting. And, as an
additional optimisation, skip diffserv parsing entirely if it is not needed
by the current configuration.
Fixes: c87b4ecdbe ("sch_cake: Make sure we can write the IP header before changing DSCP bits")
Signed-off-by: Ilya Ponetayev <i.ponetaev@ndmsystems.com>
[ fix a few style issues, reflow commit message ]
Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While the other fq-based qdiscs take advantage of skb->hash and doesn't
recompute it if it is already set, sch_cake does not.
This was a deliberate choice because sch_cake hashes various parts of the
packet header to support its advanced flow isolation modes. However,
foregoing the use of skb->hash entirely loses a few important benefits:
- When skb->hash is set by hardware, a few CPU cycles can be saved by not
hashing again in software.
- Tunnel encapsulations will generally preserve the value of skb->hash from
before the encapsulation, which allows flow-based qdiscs to distinguish
between flows even though the outer packet header no longer has flow
information.
It turns out that we can preserve these desirable properties in many cases,
while still supporting the advanced flow isolation properties of sch_cake.
This patch does so by reusing the skb->hash value as the flow_hash part of
the hashing procedure in cake_hash() only in the following conditions:
- If the skb->hash is marked as covering the flow headers (skb->l4_hash is
set)
AND
- NAT header rewriting is either disabled, or did not change any values
used for hashing. The latter is important to match local-origin packets
such as those of a tunnel endpoint.
The immediate motivation for fixing this was the recent patch to WireGuard
to preserve the skb->hash on encapsulation. As such, this is also what I
tested against; with this patch, added latency under load for competing
flows drops from ~8 ms to sub-1ms on an RRUL test over a WireGuard tunnel
going through a virtual link shaped to 1Gbps using sch_cake. This matches
the results we saw with a similar setup using sch_fq_codel when testing the
WireGuard patch.
Fixes: 046f6fd5da ("sched: Add Common Applications Kept Enhanced (cake) qdisc")
Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a straight-forward conversion case for the new function, keeping
the flow of the existing code as intact as possible.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ungrafting from PRIO bug fixes in net, when merged into net-next,
merge cleanly but create a build failure. The resolution used here is
from Petr Machata.
Signed-off-by: David S. Miller <davem@davemloft.net>
The variables 'window_interval' is u64 and do_div()
truncates it to 32 bits, which means it can test
non-zero and be truncated to zero for division.
The unit of window_interval is nanoseconds,
so its lower 32-bit is relatively easy to exceed.
Fix this issue by using div64_u64() instead.
Fixes: 7298de9cd7 ("sch_cake: Add ingress mode")
Signed-off-by: Wen Yang <wenyang@linux.alibaba.com>
Cc: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Cc: Toke Høiland-Jørgensen <toke@redhat.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Cong Wang <xiyou.wangcong@gmail.com>
Cc: cake@lists.bufferbloat.net
Cc: netdev@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Acked-by: Toke Høiland-Jørgensen <toke@toke.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Turns out tin_quantum_prio isn't used anymore and is a leftover from a
previous implementation of diffserv tins. Since the variable isn't used
in any calculations it can be eliminated.
Drop variable and places where it was set. Rename remaining variable
and consolidate naming of intermediate variables that set it.
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Acked-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This field has never been checked since introduction in mainline kernel
Signed-off-by: Victorien Molle <victorien.molle@wifirst.fr>
Signed-off-by: Florent Fourcot <florent.fourcot@wifirst.fr>
Fixes: 2db6dc2662 "sch_cake: Make gso-splitting configurable from userspace"
Acked-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We currently have two levels of strict validation:
1) liberal (default)
- undefined (type >= max) & NLA_UNSPEC attributes accepted
- attribute length >= expected accepted
- garbage at end of message accepted
2) strict (opt-in)
- NLA_UNSPEC attributes accepted
- attribute length >= expected accepted
Split out parsing strictness into four different options:
* TRAILING - check that there's no trailing data after parsing
attributes (in message or nested)
* MAXTYPE - reject attrs > max known type
* UNSPEC - reject attributes with NLA_UNSPEC policy entries
* STRICT_ATTRS - strictly validate attribute size
The default for future things should be *everything*.
The current *_strict() is a combination of TRAILING and MAXTYPE,
and is renamed to _deprecated_strict().
The current regular parsing has none of this, and is renamed to
*_parse_deprecated().
Additionally it allows us to selectively set one of the new flags
even on old policies. Notably, the UNSPEC flag could be useful in
this case, since it can be arranged (by filling in the policy) to
not be an incompatible userspace ABI change, but would then going
forward prevent forgetting attribute entries. Similar can apply
to the POLICY flag.
We end up with the following renames:
* nla_parse -> nla_parse_deprecated
* nla_parse_strict -> nla_parse_deprecated_strict
* nlmsg_parse -> nlmsg_parse_deprecated
* nlmsg_parse_strict -> nlmsg_parse_deprecated_strict
* nla_parse_nested -> nla_parse_nested_deprecated
* nla_validate_nested -> nla_validate_nested_deprecated
Using spatch, of course:
@@
expression TB, MAX, HEAD, LEN, POL, EXT;
@@
-nla_parse(TB, MAX, HEAD, LEN, POL, EXT)
+nla_parse_deprecated(TB, MAX, HEAD, LEN, POL, EXT)
@@
expression NLH, HDRLEN, TB, MAX, POL, EXT;
@@
-nlmsg_parse(NLH, HDRLEN, TB, MAX, POL, EXT)
+nlmsg_parse_deprecated(NLH, HDRLEN, TB, MAX, POL, EXT)
@@
expression NLH, HDRLEN, TB, MAX, POL, EXT;
@@
-nlmsg_parse_strict(NLH, HDRLEN, TB, MAX, POL, EXT)
+nlmsg_parse_deprecated_strict(NLH, HDRLEN, TB, MAX, POL, EXT)
@@
expression TB, MAX, NLA, POL, EXT;
@@
-nla_parse_nested(TB, MAX, NLA, POL, EXT)
+nla_parse_nested_deprecated(TB, MAX, NLA, POL, EXT)
@@
expression START, MAX, POL, EXT;
@@
-nla_validate_nested(START, MAX, POL, EXT)
+nla_validate_nested_deprecated(START, MAX, POL, EXT)
@@
expression NLH, HDRLEN, MAX, POL, EXT;
@@
-nlmsg_validate(NLH, HDRLEN, MAX, POL, EXT)
+nlmsg_validate_deprecated(NLH, HDRLEN, MAX, POL, EXT)
For this patch, don't actually add the strict, non-renamed versions
yet so that it breaks compile if I get it wrong.
Also, while at it, make nla_validate and nla_parse go down to a
common __nla_validate_parse() function to avoid code duplication.
Ultimately, this allows us to have very strict validation for every
new caller of nla_parse()/nlmsg_parse() etc as re-introduced in the
next patch, while existing things will continue to work as is.
In effect then, this adds fully strict validation for any new command.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Even if the NLA_F_NESTED flag was introduced more than 11 years ago, most
netlink based interfaces (including recently added ones) are still not
setting it in kernel generated messages. Without the flag, message parsers
not aware of attribute semantics (e.g. wireshark dissector or libmnl's
mnl_nlmsg_fprintf()) cannot recognize nested attributes and won't display
the structure of their contents.
Unfortunately we cannot just add the flag everywhere as there may be
userspace applications which check nlattr::nla_type directly rather than
through a helper masking out the flags. Therefore the patch renames
nla_nest_start() to nla_nest_start_noflag() and introduces nla_nest_start()
as a wrapper adding NLA_F_NESTED. The calls which add NLA_F_NESTED manually
are rewritten to use nla_nest_start().
Except for changes in include/net/netlink.h, the patch was generated using
this semantic patch:
@@ expression E1, E2; @@
-nla_nest_start(E1, E2)
+nla_nest_start_noflag(E1, E2)
@@ expression E1, E2; @@
-nla_nest_start_noflag(E1, E2 | NLA_F_NESTED)
+nla_nest_start(E1, E2)
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is not actually any guarantee that the IP headers are valid before we
access the DSCP bits of the packets. Fix this using the same approach taken
in sch_dsmark.
Reported-by: Kevin Darbyshire-Bryant <kevin@darbyshire-bryant.me.uk>
Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We shouldn't be using skb->protocol directly as that will miss cases with
hardware-accelerated VLAN tags. Use the helper instead to get the right
protocol number.
Reported-by: Kevin Darbyshire-Bryant <kevin@darbyshire-bryant.me.uk>
Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We initially interpreted the fwmark parameter as a flag that simply turned
on the feature, using the whole skb->mark field as the index into the CAKE
tin_order array. However, it is quite common for different applications to
use different parts of the mask field for their own purposes, each using a
different mask.
Support this use of subsets of the mark by interpreting the TCA_CAKE_FWMARK
parameter as a bitmask to apply to the fwmark field when reading it. The
result will be right-shifted by the number of unset lower bits of the mask
before looking up the tin.
In the original commit message we also failed to credit Felix Resch with
originally suggesting the fwmark feature back in 2017; so the Suggested-By
in this commit covers the whole fwmark feature.
Fixes: 0b5c7efdfc ("sch_cake: Permit use of connmarks as tin classifiers")
Suggested-by: Felix Resch <fuller@beif.de>
Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With more modes added the logic in cake_select_tin() was getting a bit
hairy, and it turns out we can actually simplify it quite a bit. This also
allows us to get rid of one of the two diffserv parsing functions, which
has the added benefit that already-zeroed DSCP fields won't get re-written.
Suggested-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add flag 'FWMARK' to enable use of firewall connmarks as tin selector.
The connmark (skbuff->mark) needs to be in the range 1->tin_cnt ie.
for diffserv3 the mark needs to be 1->3.
Background
Typically CAKE uses DSCP as the basis for tin selection. DSCP values
are relatively easily changed as part of the egress path, usually with
iptables & the mangle table, ingress is more challenging. CAKE is often
used on the WAN interface of a residential gateway where passthrough of
DSCP from the ISP is either missing or set to unhelpful values thus use
of ingress DSCP values for tin selection isn't helpful in that
environment.
An approach to solving the ingress tin selection problem is to use
CAKE's understanding of tc filters. Naive tc filters could match on
source/destination port numbers and force tin selection that way, but
multiple filters don't scale particularly well as each filter must be
traversed whether it matches or not. e.g. a simple example to map 3
firewall marks to tins:
MAJOR=$( tc qdisc show dev $DEV | head -1 | awk '{print $3}' )
tc filter add dev $DEV parent $MAJOR protocol all handle 0x01 fw action skbedit priority ${MAJOR}1
tc filter add dev $DEV parent $MAJOR protocol all handle 0x02 fw action skbedit priority ${MAJOR}2
tc filter add dev $DEV parent $MAJOR protocol all handle 0x03 fw action skbedit priority ${MAJOR}3
Another option is to use eBPF cls_act with tc filters e.g.
MAJOR=$( tc qdisc show dev $DEV | head -1 | awk '{print $3}' )
tc filter add dev $DEV parent $MAJOR bpf da obj my-bpf-fwmark-to-class.o
This has the disadvantages of a) needing someone to write & maintain
the bpf program, b) a bpf toolchain to compile it and c) needing to
hardcode the major number in the bpf program so it matches the cake
instance (or forcing the cake instance to a particular major number)
since the major number cannot be passed to the bpf program via tc
command line.
As already hinted at by the previous examples, it would be helpful
to associate tins with something that survives the Internet path and
ideally allows tin selection on both egress and ingress. Netfilter's
conntrack permits setting an identifying mark on a connection which
can also be restored to an ingress packet with tc action connmark e.g.
tc filter add dev eth0 parent ffff: protocol all prio 10 u32 \
match u32 0 0 flowid 1:1 action connmark action mirred egress redirect dev ifb1
Since tc's connmark action has restored any connmark into skb->mark,
any of the previous solutions are based upon it and in one form or
another copy that mark to the skb->priority field where again CAKE
picks this up.
This change cuts out at least one of the (less intuitive &
non-scalable) middlemen and permit direct access to skb->mark.
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
CAKE host fairness does not work well with TCP flows in dual-srchost and
dual-dsthost setup. The reason is that ACKs generated by TCP flows are
classified as sparse flows, and affect flow isolation from other hosts. Fix
this by calculating host_load based only on the bulk flows a host
generates. In a hash collision the host_bulk_flow_count values must be
decremented on the old hosts and incremented on the new ones *if* the queue
is in the bulk set.
Reported-by: Pete Heist <peteheist@gmail.com>
Signed-off-by: George Amanakis <gamanakis@gmail.com>
Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To ensure parent qdiscs have the same notion of the number of enqueued
packets even after splitting a GSO packet, update the qdisc tree with the
number of packets that was added due to the split.
Reported-by: Pete Heist <pete@heistp.net>
Tested-by: Pete Heist <pete@heistp.net>
Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts were easy to resolve using immediate context mostly,
except the cls_u32.c one where I simply too the entire HEAD
chunk.
Signed-off-by: David S. Miller <davem@davemloft.net>
As done treewide earlier, this catches several more open-coded
allocation size calculations that were added to the kernel during the
merge window. This performs the following mechanical transformations
using Coccinelle:
kvmalloc(a * b, ...) -> kvmalloc_array(a, b, ...)
kvzalloc(a * b, ...) -> kvcalloc(a, b, ...)
devm_kzalloc(..., a * b, ...) -> devm_kcalloc(..., a, b, ...)
Signed-off-by: Kees Cook <keescook@chromium.org>
An SKB is not on a list if skb->next is NULL.
Codify this convention into a helper function and use it
where we are dequeueing an SKB and need to mark it as such.
Signed-off-by: David S. Miller <davem@davemloft.net>
The TC filter flow mapping override completely skipped the call to
cake_hash(); however that meant that the internal state was not being
updated, which ultimately leads to deadlocks in some configurations. Fix
that by passing the overridden flow ID into cake_hash() instead so it can
react appropriately.
In addition, the major number of the class ID can now be set to override
the host mapping in host isolation mode. If both host and flow are
overridden (or if the respective modes are disabled), flow dissection and
hashing will be skipped entirely; otherwise, the hashing will be kept for
the portions that are not set by the filter.
Signed-off-by: Toke Høiland-Jørgensen <toke@toke.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove including <linux/version.h> that don't need it.
Signed-off-by: Yue Haibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In diffserv mode, CAKE stores tins in a different order internally than
the logical order exposed to userspace. The order remapping was missing
in the handling of 'tc filter' priority mappings through skb->priority,
resulting in bulk and best effort mappings being reversed relative to
how they are displayed.
Fix this by adding the missing mapping when reading skb->priority.
Fixes: 83f8fd69af ("sch_cake: Add DiffServ handling")
Signed-off-by: Toke Høiland-Jørgensen <toke@toke.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
At lower bandwidths, the transmission time of a single GSO segment can add
an unacceptable amount of latency due to HOL blocking. Furthermore, with a
software shaper, any tuning mechanism employed by the kernel to control the
maximum size of GSO segments is thrown off by the artificial limit on
bandwidth. For this reason, we split GSO segments into their individual
packets iff the shaper is active and configured to a bandwidth <= 1 Gbps.
Signed-off-by: Toke Høiland-Jørgensen <toke@toke.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Xin Long
Linus Torvalds
Zhengchao Shao
Jason A. Donenfeld
Kevin Bracey
Eric Dumazet
Jakub Kicinski
Toke Høiland-Jørgensen
Davide Caratti
Tyson Moore
Maxim Mikityanskiy
Gustavo A. R. Silva
Petr Machata
Kees Cook
David S. Miller
Kevin Darbyshire-Bryant
Ilya Ponetayev
Wen Yang
Victorien Molle
Johannes Berg
Michal Kubecek
Toke Høiland-Jørgensen
George Amanakis
Yue Haibing
Dave Taht