Add a new entry to 'enum mem_type' and a new string to 'edac_mem_types[]'
for HBM2 (High Bandwidth Memory Gen 2) new memory type.
Reviewed-by: Yazen Ghannam <yazen.ghannam@amd.com>
Signed-off-by: Muralidhara M K <muralimk@amd.com>
Signed-off-by: Naveen Krishna Chatradhi <nchatrad@amd.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Link: https://lore.kernel.org/r/20210630152828.162659-4-nchatrad@amd.com
Add a new entry to 'enum mem_type' and a new string to
'edac_mem_types[]' for DDR5 new memory type.
Signed-off-by: Qiuxu Zhuo <qiuxu.zhuo@intel.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
There are {Low-Power DDR3/4, WIO2} types of memory.
Add new entries to 'enum mem_type' and new strings to
'edac_mem_types[]' for the new types.
Signed-off-by: Qiuxu Zhuo <qiuxu.zhuo@intel.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
When acpi_extlog was added, we were worried that the same error would
be reported more than once by different subsystems. But in the ensuing
years I've seen complaints that people could not find an error log
(because this mechanism suppressed the log they were looking for).
Rip it all out. People are smart enough to notice the same address from
different reporting mechanisms.
Signed-off-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Tested-by: Tony Luck <tony.luck@intel.com>
Link: https://lkml.kernel.org/r/20200214222720.13168-8-tony.luck@intel.com
Looking at how mci->{ue,ce}_per_layer[EDAC_MAX_LAYERS] is used, it
turns out that only the leaves in the memory hierarchy are consumed
(in sysfs), but not the intermediate layers, e.g.:
count = dimm->mci->ce_per_layer[dimm->mci->n_layers-1][dimm->idx];
These unused counters only add complexity, remove them. The error
counter values are directly stored in struct dimm_info now.
Signed-off-by: Robert Richter <rrichter@marvell.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Acked-by: Aristeu Rozanski <aris@redhat.com>
Link: https://lkml.kernel.org/r/20200123090210.26933-11-rrichter@marvell.com
Many functions carry the enable_per_layer_report argument. This is a
bool value indicating the error information contains some location
data where the error occurred. This can easily being determined by
checking the pos[] array for values. Negative values indicate there is
no location available. So if the top layer is negative, the error
location is unknown.
Just check if the top layer is negative and remove
enable_per_layer_report as function argument and also from struct
edac_raw_error_desc.
[ bp: Reflow comments to 80 columns, while at it. ]
Signed-off-by: Robert Richter <rrichter@marvell.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Acked-by: Aristeu Rozanski <aris@redhat.com>
Link: https://lkml.kernel.org/r/20200123090210.26933-8-rrichter@marvell.com
Store the error type in struct edac_raw_error_desc. This makes the
type parameter of edac_raw_mc_handle_error() obsolete.
[ kernel-doc typo ]
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Robert Richter <rrichter@marvell.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Acked-by: Aristeu Rozanski <aris@redhat.com>
Link: https://lkml.kernel.org/r/20200123090210.26933-4-rrichter@marvell.com
There never has been such function edac_raw_error_desc_clean() and in
function ghes_edac_report_mem_error() the whole struct is zero'ed
including the string arrays. Remove that comment.
Signed-off-by: Robert Richter <rrichter@marvell.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Cc: "linux-edac@vger.kernel.org" <linux-edac@vger.kernel.org>
Cc: James Morse <james.morse@arm.com>
Cc: Tony Luck <tony.luck@intel.com>
Link: https://lkml.kernel.org/r/20191106093239.25517-9-rrichter@marvell.com
Introduce an mci_for_each_dimm() iterator. It returns a pointer to
a struct dimm_info. This makes the declaration and use of an index
obsolete and avoids access to internal data of struct mci (direct array
access etc).
[ bp: push the struct dimm_info *dimm; declaration into the
CONFIG_EDAC_DEBUG block. ]
Signed-off-by: Robert Richter <rrichter@marvell.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Cc: "linux-edac@vger.kernel.org" <linux-edac@vger.kernel.org>
Cc: James Morse <james.morse@arm.com>
Cc: Tony Luck <tony.luck@intel.com>
Link: https://lkml.kernel.org/r/20191106093239.25517-4-rrichter@marvell.com
The EDAC_DIMM_OFF() macro takes 5 arguments to get the DIMM's index.
Simplify this by storing the index in struct dimm_info to avoid its
calculation and remove the EDAC_DIMM_OFF() macro. The index can be
directly used then.
Another advantage is that edac_mc_alloc() could be used even if the
exact size of the layers is unknown. Only the number of DIMMs would be
needed.
Rename iterator variable to idx, while at it. The name is more handy,
esp. when searching for it in the code.
Signed-off-by: Robert Richter <rrichter@marvell.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Cc: "linux-edac@vger.kernel.org" <linux-edac@vger.kernel.org>
Cc: James Morse <james.morse@arm.com>
Cc: Tony Luck <tony.luck@intel.com>
Link: https://lkml.kernel.org/r/20191106093239.25517-3-rrichter@marvell.com
The EDAC_DIMM_PTR() macro takes 3 arguments from struct mem_ctl_info.
Clean up this interface to only pass the mci struct and replace this
macro with a new function edac_get_dimm().
Also introduce an edac_get_dimm_by_index() function for later use.
This allows it to get a DIMM pointer only by a given index. This can
be useful if the DIMM's position within the layers of the memory
controller or the exact size of the layers are unknown.
Small style changes made for some hunks after applying the semantic
patch.
Semantic patch used:
@@ expression mci, a, b,c; @@
-EDAC_DIMM_PTR(mci->layers, mci->dimms, mci->n_layers, a, b, c)
+edac_get_dimm(mci, a, b, c)
[ bp: Touchups. ]
Signed-off-by: Robert Richter <rrichter@marvell.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Cc: "linux-edac@vger.kernel.org" <linux-edac@vger.kernel.org>
Cc: James Morse <james.morse@arm.com>
Cc: Jason Baron <jbaron@akamai.com>
Cc: Qiuxu Zhuo <qiuxu.zhuo@intel.com>
Cc: Tero Kristo <t-kristo@ti.com>
Cc: Tony Luck <tony.luck@intel.com>
Link: https://lkml.kernel.org/r/20191106093239.25517-2-rrichter@marvell.com
Use of 'unsigned int' instead of bare use of 'unsigned'. Fix this for
edac_mc*, ghes and the i5100 driver as reported by checkpatch.pl.
While at it, struct member dev_ch_attribute->channel is always used as
unsigned int. Change type to unsigned int to avoid type casts.
[ bp: Massage. ]
Signed-off-by: Robert Richter <rrichter@marvell.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Cc: "linux-edac@vger.kernel.org" <linux-edac@vger.kernel.org>
Cc: James Morse <james.morse@arm.com>
Cc: Tony Luck <tony.luck@intel.com>
Link: https://lkml.kernel.org/r/20190902123216.9809-2-rrichter@marvell.com
... and use the single edac_subsys object returned from
subsys_system_register(). The idea is to have a single bus
and multiple devices on it.
Signed-off-by: Borislav Petkov <bp@suse.de>
Acked-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
CC: Aristeu Rozanski Filho <arozansk@redhat.com>
CC: Greg KH <gregkh@linuxfoundation.org>
CC: Justin Ernst <justin.ernst@hpe.com>
CC: linux-edac <linux-edac@vger.kernel.org>
CC: Mauro Carvalho Chehab <mchehab@kernel.org>
CC: Russ Anderson <rja@hpe.com>
Cc: Tony Luck <tony.luck@intel.com>
Link: https://lkml.kernel.org/r/20180926152752.GG5584@zn.tnic
We observe an oops in the skx_edac module during boot:
EDAC MC0: Giving out device to module skx_edac controller Skylake Socket#0 IMC#0
EDAC MC1: Giving out device to module skx_edac controller Skylake Socket#0 IMC#1
EDAC MC2: Giving out device to module skx_edac controller Skylake Socket#1 IMC#0
...
EDAC MC13: Giving out device to module skx_edac controller Skylake Socket#0 IMC#1
EDAC MC14: Giving out device to module skx_edac controller Skylake Socket#1 IMC#0
EDAC MC15: Giving out device to module skx_edac controller Skylake Socket#1 IMC#1
Too many memory controllers: 16
EDAC MC: Removed device 0 for skx_edac Skylake Socket#0 IMC#0
We observe there are two memory controllers per socket, with a limit
of 16. Raise the maximum number of memory controllers from 16 to 2 *
MAX_NUMNODES (1024).
[ bp: This is just a band-aid fix until we've sorted out the whole issue
with the bus_type association and handling in EDAC and can get rid of
this arbitrary limit. ]
Signed-off-by: Justin Ernst <justin.ernst@hpe.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Acked-by: Russ Anderson <russ.anderson@hpe.com>
Cc: Mauro Carvalho Chehab <mchehab@kernel.org>
Cc: linux-edac@vger.kernel.org
Link: https://lkml.kernel.org/r/20180925143449.284634-1-justin.ernst@hpe.com
There are now non-volatile versions of DIMMs. Add a new entry to "enum
mem_type" and a new string in edac_mem_types[].
Signed-off-by: Tony Luck <tony.luck@intel.com>
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Cc: Aristeu Rozanski <aris@redhat.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Jean Delvare <jdelvare@suse.com>
Cc: Len Brown <lenb@kernel.org>
Cc: Mauro Carvalho Chehab <mchehab@kernel.org>
Cc: Qiuxu Zhuo <qiuxu.zhuo@intel.com>
Cc: linux-acpi@vger.kernel.org
Cc: linux-edac <linux-edac@vger.kernel.org>
Cc: linux-nvdimm@lists.01.org
Link: http://lkml.kernel.org/r/20180312182430.10335-3-tony.luck@intel.com
Signed-off-by: Borislav Petkov <bp@suse.de>
It is a write-only variable so get rid of it.
Signed-off-by: Borislav Petkov <bp@suse.de>
Acked-by: Robert Richter <rric@kernel.org>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Thor Thayer <thor.thayer@linux.intel.com>
Acked-by: Tony Luck <tony.luck@intel.com>
Cc: Mark Gross <mark.gross@intel.com>
Cc: Tim Small <tim@buttersideup.com>
Cc: Ranganathan Desikan <ravi@jetztechnologies.com>
Cc: "Arvind R." <arvino55@gmail.com>
Cc: Jason Baron <jbaron@akamai.com>
Cc: "Sören Brinkmann" <soren.brinkmann@xilinx.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: David Daney <david.daney@cavium.com>
Cc: Loc Ho <lho@apm.com>
Cc: linux-edac@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-mips@linux-mips.org
Use mc_devices list instead to check whether we have EDAC driver
instances successfully registered with EDAC core.
Signed-off-by: Borislav Petkov <bp@suse.de>
Apparently, some machines used to report DRAM errors through a PCI SERR
NMI. This is why we have a call into EDAC in the NMI handler. See
c0d1217202 ("drivers/edac: add new nmi rescan").
From looking at the patch above, that's two drivers: e752x_edac.c and
e7xxx_edac.c. Now, I wanna say those are old machines which are probably
decommissioned already.
Tony says that "[t]the newest CPU supported by either of those drivers
is the Xeon E7520 (a.k.a. "Nehalem") released in Q1'2010. Possibly some
folks are still using these ... but people that hold onto h/w for 7
years generally cling to old s/w too ... so I'd guess it unlikely that
we will get complaints for breaking these in upstream."
So even if there is a small number still in use, we did load EDAC with
edac_op_state == EDAC_OPSTATE_POLL by default (we still do, in fact)
which means a default EDAC setup without any parameters supplied on the
command line or otherwise would never even log the error in the NMI
handler because we're polling by default:
inline int edac_handler_set(void)
{
if (edac_op_state == EDAC_OPSTATE_POLL)
return 0;
return atomic_read(&edac_handlers);
}
So, long story short, I'd like to get rid of that nastiness called
edac_stub.c and confine all the EDAC drivers solely to drivers/edac/. If
we ever have to do stuff like that again, it should be notifiers we're
using and not some insanity like this one.
Signed-off-by: Borislav Petkov <bp@suse.de>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Tony Luck <tony.luck@intel.com>
Add a description of the HW_EVENT_ERR_DEFERRED type that wasn't included
with commit d12a969ebb ("EDAC, amd64: Add Deferred Error type").
Signed-off-by: Yazen Ghannam <Yazen.Ghannam@amd.com>
Acked-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Instead of storing the concepts dictionary inside header file,
move it to the subsystem documentation.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
As this file was never added to the driver-api, the kernel-doc
markups there were never tested. Some of them have issues.
Fix them.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The edac_core.h header contain data structures and function
definitions for the 3 parts of EDAC: MC, PCI and device.
Let's move the PCI ones to a separate header file, as part
of a header reorganization.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Currently, deferred errors are classified as correctable in EDAC. Add a
new error type for deferred errors so that they are correctly reported
to the user.
Signed-off-by: Yazen Ghannam <Yazen.Ghannam@amd.com>
Cc: Aravind Gopalakrishnan <aravindksg.lkml@gmail.com>
Cc: linux-edac <linux-edac@vger.kernel.org>
Link: http://lkml.kernel.org/r/1479423463-8536-7-git-send-email-Yazen.Ghannam@amd.com
Signed-off-by: Borislav Petkov <bp@suse.de>
AMD Fam17h systems can support Load-Reduced DDR4 DIMMs. So add this new
type to edac.h in preparation for the Fam17h EDAC update. Also, let's
fix a format issue with the LRDDR3 line while we're here.
Signed-off-by: Yazen Ghannam <Yazen.Ghannam@amd.com>
Cc: Aravind Gopalakrishnan <aravindksg.lkml@gmail.com>
Cc: linux-edac <linux-edac@vger.kernel.org>
Link: http://lkml.kernel.org/r/1479423463-8536-3-git-send-email-Yazen.Ghannam@amd.com
Signed-off-by: Borislav Petkov <bp@suse.de>
This was really dumb - reference counting for the main EDAC sysfs
object. While we could've simply registered it as the first thing in the
module init path and then hand it around to what needs it.
Do that and rip out all the code around it, thus simplifying the whole
handling significantly.
Move the edac_subsys node back to edac_module.c.
Signed-off-by: Borislav Petkov <bp@suse.de>
Here's the "big" driver core updates for 4.4-rc1. Primarily a bunch of
debugfs updates, with a smattering of minor driver core fixes and
updates as well.
All have been in linux-next for a long time.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlY6ePQACgkQMUfUDdst+ymNTgCgpP0CZw57GpwF/Hp2L/lMkVeo
Kx8AoKhEi4iqD5fdCQS9qTfomB+2/M6g
=g7ZO
-----END PGP SIGNATURE-----
Merge tag 'driver-core-4.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg KH:
"Here's the "big" driver core updates for 4.4-rc1. Primarily a bunch
of debugfs updates, with a smattering of minor driver core fixes and
updates as well.
All have been in linux-next for a long time"
* tag 'driver-core-4.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
debugfs: Add debugfs_create_ulong()
of: to support binding numa node to specified device in devicetree
debugfs: Add read-only/write-only bool file ops
debugfs: Add read-only/write-only size_t file ops
debugfs: Add read-only/write-only x64 file ops
debugfs: Consolidate file mode checks in debugfs_create_*()
Revert "mm: Check if section present during memory block (un)registering"
driver-core: platform: Provide helpers for multi-driver modules
mm: Check if section present during memory block (un)registering
devres: fix a for loop bounds check
CMA: fix CONFIG_CMA_SIZE_MBYTES overflow in 64bit
base/platform: assert that dev_pm_domain callbacks are called unconditionally
sysfs: correctly handle short reads on PREALLOC attrs.
base: soc: siplify ida usage
kobject: move EXPORT_SYMBOL() macros next to corresponding definitions
kobject: explain what kobject's sd field is
debugfs: document that debugfs_remove*() accepts NULL and error values
debugfs: Pass bool pointer to debugfs_create_bool()
ACPI / EC: Fix broken 64bit big-endian users of 'global_lock'
Its a bit odd that debugfs_create_bool() takes 'u32 *' as an argument,
when all it needs is a boolean pointer.
It would be better to update this API to make it accept 'bool *'
instead, as that will make it more consistent and often more convenient.
Over that bool takes just a byte.
That required updates to all user sites as well, in the same commit
updating the API. regmap core was also using
debugfs_{read|write}_file_bool(), directly and variable types were
updated for that to be bool as well.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
... into a separate compilation unit and drop a couple of
CONFIG_EDAC_DEBUG ifdefferies. Rename edac_create_debug_nodes() to
edac_create_debugfs_nodes(), while at it.
No functionality change.
Cc: <linux-edac@vger.kernel.org>
Signed-off-by: Borislav Petkov <bp@suse.de>
Haswell memory controller can make use of DDR4 and Registered DDR4
Cc: tony.luck@intel.com
Signed-off-by: Aristeu Rozanski <aris@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This new parameter is used to control how to report HW error reporting,
especially for newer Intel platform, like Ivybridge-EX, which contains
an enhanced error decoding functionality in the firmware, i.e. eMCA.
Signed-off-by: Chen, Gong <gong.chen@linux.intel.com>
Acked-by: Tony Luck <tony.luck@intel.com>
Link: http://lkml.kernel.org/r/1386310630-12529-2-git-send-email-gong.chen@linux.intel.com
[ Boris: massage commit message. ]
Signed-off-by: Borislav Petkov <bp@suse.de>
In latest UEFI spec(by now it's 2.4) there are some new
fields for memory error reporting. Add these new fields for
ghes_edac interface.
Signed-off-by: Chen, Gong <gong.chen@linux.intel.com>
Cc: Mauro Carvalho Chehab <m.chehab@samsung.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Both mci.mem_is_per_rank and mci.csbased denote the same thing: the
memory controller is csrows based. Merge both fields into one.
There's no need for the driver to actually fill it, as the core detects
it by checking if one of the layers has the csrows type as part of the
memory hierarchy:
if (layers[i].type == EDAC_MC_LAYER_CHIP_SELECT)
per_rank = true;
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
We were filling the csrow size with a wrong value. 16a528ee39 ("EDAC:
Fix csrow size reported in sysfs") tried to address the issue. It fixed
the report with the old API but not with the new one. Correct it for the
new API too.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
[ make it a per-csrow accounting regardless of ->channel_count ]
Signed-off-by: Borislav Petkov <bp@suse.de>
The CPER spec defines a forth type of error: informational
logs. Add support for it at the edac API and at the
trace event interface.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The number of variables at the stack is too big.
Reduces the stack usage by using a pre-allocated error
buffer.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There are some cases where the memory controller layout is
completely hidden. This is the case of firmware-driven error
code, like the one provided by GHES. Add a new layer to be
used on such memory error report mechanisms.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There are no more embedded kobjects in struct mem_ctl_info. Remove a header and
a comment that does not reflect the code anymore.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Naveen Krishna Chatradhi
Borislav Petkov
Qiuxu Zhuo
Mauro Carvalho Chehab
Tony Luck
Robert Richter
Justin Ernst
Fan Wu
Alexander Alemayhu
Yazen Ghannam
Mauro Carvalho Chehab
Jim Snow
Linus Torvalds
Viresh Kumar
Aravind Gopalakrishnan
Aristeu Rozanski
Chen, Gong
Mauro Carvalho Chehab
Shaun Ruffell