This patch applies customized PCI_DEVICE_ macros to specify the pci_ids
instead of open-coding them within the sdhci-pci driver.
By introducing device specific macros the pci_ids table becomes much
shorter and easier to comprehend than it would be possible using the
generic version of the PCI_DEVICE_ macros.
Signed-off-by: Matthias Kraemer <matthiasmartinsson@gmail.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The SDHCI_QUIRK_NO_MULTIBLOCK quirk was used as a workaround for the
ENGcm07207 erratum. However, it caused excruciatingly slow SD transfers
(300 kB/s on average), and this erratum actually does not imply that
multiple-block transfers are not supported, so this was overkill.
The suggested workaround for this erratum is to set SYSCTL.RSTA, but the
simple DAT line software reset (which resets the DMA circuit among
others) triggered by sdhci_finish_data() in case of errors seems to be
sufficient. Indeed, generating errors in a controlled manner on i.MX25
using the FEVT register right in the middle of read data transfers
without this quirk shows that nothing is written to the buffer by the
eSDHC past CMD12, and no extra Auto CMD12 is sent with AC12EN set, so
the data transfers on AHB are properly aborted. For write data
transfers, neither extra data nor extra Auto CMD12 is sent, as expected.
Moreover, after intensive stress tests on i.MX25, removing
SDHCI_QUIRK_NO_MULTIBLOCK seems to be safe.
SDHCI_QUIRK_BROKEN_ADMA has nothing to do with ENGcm07207, so set
ESDHC_FLAG_ERR004536 for the devices that had ESDHC_FLAG_ENGCM07207 set
in order to continue getting SDHCI_QUIRK_BROKEN_ADMA.
Signed-off-by: Benoît Thébaudeau <benoit@wsystem.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
On i.MX, SYSCTL.SDCLKFS may always be set to 0 in order to make the SD
clock frequency prescaler divide by 1 in SDR mode, even with the eSDHC.
The previous minimum prescaler value of 2 in SDR mode with the eSDHC was
a code remnant from PowerPC, which actually has this limitation on
earlier revisions.
In DDR mode, the prescaler can divide by up to 512.
The maximum SD clock frequency in High Speed mode is 50 MHz. On i.MX25,
this change makes it possible to get 48 MHz from the USB PLL
(240 MHz / 5 / 1) instead of only 40 MHz from the USB PLL
(240 MHz / 3 / 2) or 33.25 MHz from the AHB clock (133 MHz / 2 / 2).
Signed-off-by: Benoît Thébaudeau <benoit@wsystem.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
On i.MX25, the eSDHC DAT line software reset (SYSCTL.RSTD) unexpectedly
clears at least the data transfer width (PROCTL.DTW), which then results
in data CRC errors. This behavior is not documented, but it has actually
been observed. Consequently, the DAT line software resets triggered by
sdhci.c in case of errors caused unrecoverable errors.
Fix this by making sure that the DAT line software reset does not alter
the Host Control register. This behavior being undocumented, it may also
be present on other i.MX SoCs, so apply this fix for the whole i.MX
family.
Signed-off-by: Benoît Thébaudeau <benoit@wsystem.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The eSDHC can only DMA from 32-bit-aligned addresses.
This fixes the following test cases of mmc_test:
11: Badly aligned write
12: Badly aligned read
13: Badly aligned multi-block write
14: Badly aligned multi-block read
Signed-off-by: Benoît Thébaudeau <benoit@wsystem.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Fix various English mistakes and typos in comments and in printed
strings.
Signed-off-by: Benoît Thébaudeau <benoit@wsystem.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Null check at line 1165: if (mrq->cmd), implies that mrq->cmd might
be NULL.
Add null checks before dereferencing pointer mrq->cmd in order to avoid
any potential NULL pointer dereference.
Addresses-Coverity-ID: 1408740
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
It is 'R-Car', not 'RCar'. No code or binding changes, only descriptive text.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Using the device_property interfaces allows mmc drivers to work
on platforms which run on either device tree or ACPI.
Signed-off-by: David Woods <dwoods@mellanox.com>
Reviewed-by: Chris Metcalf <cmetcalf@mellanox.com>
Cc: stable@vger.linux.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Using the device_property interfaces allows the dw_mmc driver to work
on platforms which run on either device tree or ACPI.
Signed-off-by: David Woods <dwoods@mellanox.com>
Reviewed-by: Chris Metcalf <cmetcalf@mellanox.com>
Cc: stable@vger.linux.org
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
clk_prepare_enable() may fail, so we should better check its return value
and propagate it in the case of error.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The only reason to why the mmc block device driver needs to implements its
own version of how to get the status of the card, is that it needs to
specify a different amount of retries.
Therefore add a new exported function which allows the caller to specify
the number of retries and convert everybody to use it, as this simplifies
the code.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
This moves the boot partition lock command (issued from sysfs)
into a custom block layer request, just like the ioctl()s,
getting rid of yet another instance of mmc_get_card().
Since we now have two operations issuing special DRV_OP's, we
rename the result variable ->drv_op_result.
Tested by locking the boot partition from userspace:
> cd /sys/devices/platform/soc/80114000.sdi4_per2/mmc_host/mmc3/
mmc3:0001/block/mmcblk3/mmcblk3boot0
> echo 1 > ro_lock_until_next_power_on
[ 178.645324] mmcblk3boot1: Locking boot partition ro until next power on
[ 178.652221] mmcblk3boot0: Locking boot partition ro until next power on
Also tested this with a huge dd job in the background: it
is now possible to lock the boot partitions on the card even
under heavy I/O.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
We will need to access static functions above the pure block layer
operations in the file, so move the driver operations issue
function down so we can see all non-blocklayer symbols.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
We will expand the DRV_OP usage, so we need to know which
operation we're performing. Tag the operations with an
enum:ed type and rename the function so it is clear that
it deals with any command and put a switch statement in
it. Currently only ioctls are supported.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Just as we can use blk_mq_rq_from_pdu() to get the per-request
tag we can use blk_mq_rq_to_pdu() to get a request from a tag.
Introduce a static inline helper so we are on the clear what
is happening.
Suggested-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Plain code move with no changes. Needed for refactoring. Also, looks
nicer if request and finish_request are next to each other.
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The obviously wrong comment was added in 2011 with commit df3ef2d3c9
("mmc: protect the tmio_mmc driver against a theoretical race") but
already obsoleted half a year later with commit b9269fdd4f ("mmc:
tmio: fix recursive spinlock, don't schedule with interrupts disabled").
Fixes: b9269fdd4f ("mmc: tmio: fix recursive spinlock, don't schedule with interrupts disabled")
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Split handling mrq into a seperate function. We need to call it from
another place soon.
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This part confused me and I had to read it twice until I got it. Let's
follow the standard pattern to bail out if something is wrong and keep
in the body of the function when everything is as expected.
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
commit cdf8a6fb48
"mmc: block: Introduce queue semantics"
deleted the last user of mmc_req_is_special() and it was
a horrible hack to classify requests as "special" or
"not special" to begin with, so delete the helper.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This switches also the multiple-command ioctl() call to issue
all ioctl()s through the block layer instead of going directly
to the device.
We extend the passed argument with an argument count and loop
over all passed commands in the ioctl() issue function called
from the block layer.
By doing this we are again loosening the grip on the big host
lock, since two calls to mmc_get_card()/mmc_put_card() are
removed.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Avri Altman <Avri.Altman@sandisk.com>
This wraps single ioctl() commands into block requests using
the custom block layer request types REQ_OP_DRV_IN and
REQ_OP_DRV_OUT.
By doing this we are loosening the grip on the big host lock,
since two calls to mmc_get_card()/mmc_put_card() are removed.
We are storing the ioctl() in/out argument as a pointer in
the per-request struct mmc_blk_request container. Since we
now let the block layer allocate this data, blk_get_request()
will allocate it for us and we can immediately dereference
it and use it to pass the argument into the block layer.
We refactor the if/else/if/else ladder in mmc_blk_issue_rq()
as part of the job, keeping some extra attention to the
case when a NULL req is passed into this function and
making that pipeline flush more explicit.
Tested on the ux500 with the userspace:
mmc extcsd read /dev/mmcblk3
resulting in a successful EXTCSD info dump back to the
console.
This commit fixes a starvation issue in the MMC/SD stack
that can be easily provoked in the following way by
issueing the following commands in sequence:
> dd if=/dev/mmcblk3 of=/dev/null bs=1M &
> mmc extcs read /dev/mmcblk3
Before this patch, the extcsd read command would hang
(starve) while waiting for the dd command to finish since
the block layer was holding the card/host lock.
After this patch, the extcsd ioctl() command is nicely
interpersed with the rest of the block commands and we
can issue a bunch of ioctl()s from userspace while there
is some busy block IO going on without any problems.
Conversely userspace ioctl()s can no longer starve
the block layer by holding the card/host lock.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Avri Altman <Avri.Altman@sandisk.com>
The variable is_rpmb is clearly a bool and even assigned true
and false, yet declared as an int.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The mmc_queue_req is a per-request state container the MMC core uses
to carry bounce buffers, pointers to asynchronous requests and so on.
Currently allocated as a static array of objects, then as a request
comes in, a mmc_queue_req is assigned to it, and used during the
lifetime of the request.
This is backwards compared to how other block layer drivers work:
they usally let the block core provide a per-request struct that get
allocated right beind the struct request, and which can be obtained
using the blk_mq_rq_to_pdu() helper. (The _mq_ infix in this function
name is misleading: it is used by both the old and the MQ block
layer.)
The per-request struct gets allocated to the size stored in the queue
variable .cmd_size initialized using the .init_rq_fn() and
cleaned up using .exit_rq_fn().
The block layer code makes the MMC core rely on this mechanism to
allocate the per-request mmc_queue_req state container.
Doing this make a lot of complicated queue handling go away. We only
need to keep the .qnct that keeps count of how many request are
currently being processed by the MMC layer. The MQ block layer will
replace also this once we transition to it.
Doing this refactoring is necessary to move the ioctl() operations
into custom block layer requests tagged with REQ_OP_DRV_[IN|OUT]
instead of the custom code using the BigMMCHostLock that we have
today: those require that per-request data be obtainable easily from
a request after creating a custom request with e.g.:
struct request *rq = blk_get_request(q, REQ_OP_DRV_IN, __GFP_RECLAIM);
struct mmc_queue_req *mq_rq = req_to_mq_rq(rq);
And this is not possible with the current construction, as the request
is not immediately assigned the per-request state container, but
instead it gets assigned when the request finally enters the MMC
queue, which is way too late for custom requests.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
[Ulf: Folded in the fix to drop a call to blk_cleanup_queue()]
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Heiner Kallweit <hkallweit1@gmail.com>
This option is activated by all multiplatform configs and what
not so we almost always have it turned on, and the memory it
saves is negligible, even more so moving forward. The actual
bounce buffer only gets allocated only when used, the only
thing the ifdefs are saving is a little bit of code.
It is highly improper to have this as a Kconfig option that
get turned on by Kconfig, make this a pure runtime-thing and
let the host decide whether we use bounce buffers. We add a
new property "disable_bounce" to the host struct.
Notice that mmc_queue_calc_bouncesz() already disables the
bounce buffers if host->max_segs != 1, so any arch that has a
maximum number of segments higher than 1 will have bounce
buffers disabled.
The option CONFIG_MMC_BLOCK_BOUNCE is default y so the
majority of platforms in the kernel already have it on, and
it then gets turned off at runtime since most of these have
a host->max_segs > 1. The few exceptions that have
host->max_segs == 1 and still turn off the bounce buffering
are those that disable it in their defconfig.
Those are the following:
arch/arm/configs/colibri_pxa300_defconfig
arch/arm/configs/zeus_defconfig
- Uses MMC_PXA, drivers/mmc/host/pxamci.c
- Sets host->max_segs = NR_SG, which is 1
- This needs its bounce buffer deactivated so we set
host->disable_bounce to true in the host driver
arch/arm/configs/davinci_all_defconfig
- Uses MMC_DAVINCI, drivers/mmc/host/davinci_mmc.c
- This driver sets host->max_segs to MAX_NR_SG, which is 16
- That means this driver anyways disabled bounce buffers
- No special action needed for this platform
arch/arm/configs/lpc32xx_defconfig
arch/arm/configs/nhk8815_defconfig
arch/arm/configs/u300_defconfig
- Uses MMC_ARMMMCI, drivers/mmc/host/mmci.[c|h]
- This driver by default sets host->max_segs to NR_SG,
which is 128, unless a DMA engine is used, and in that case
the number of segments are also > 1
- That means this driver already disables bounce buffers
- No special action needed for these platforms
arch/arm/configs/sama5_defconfig
- Uses MMC_SDHCI, MMC_SDHCI_PLTFM, MMC_SDHCI_OF_AT91, MMC_ATMELMCI
- Uses drivers/mmc/host/sdhci.c
- Normally sets host->max_segs to SDHCI_MAX_SEGS which is 128 and
thus disables bounce buffers
- Sets host->max_segs to 1 if SDHCI_USE_SDMA is set
- SDHCI_USE_SDMA is only set by SDHCI on PCI adapers
- That means that for this platform bounce buffers are already
disabled at runtime
- No special action needed for this platform
arch/blackfin/configs/CM-BF533_defconfig
arch/blackfin/configs/CM-BF537E_defconfig
- Uses MMC_SPI (a simple MMC card connected on SPI pins)
- Uses drivers/mmc/host/mmc_spi.c
- Sets host->max_segs to MMC_SPI_BLOCKSATONCE which is 128
- That means this platform already disables bounce buffers at
runtime
- No special action needed for these platforms
arch/mips/configs/cavium_octeon_defconfig
- Uses MMC_CAVIUM_OCTEON, drivers/mmc/host/cavium.c
- Sets host->max_segs to 16 or 1
- Setting host->disable_bounce to be sure for the 1 case
arch/mips/configs/qi_lb60_defconfig
- Uses MMC_JZ4740, drivers/mmc/host/jz4740_mmc.c
- This sets host->max_segs to 128 so bounce buffers are
already runtime disabled
- No action needed for this platform
It would be interesting to come up with a list of the platforms
that actually end up using bounce buffers. I have not been
able to infer such a list, but it occurs when
host->max_segs == 1 and the bounce buffering is not explicitly
disabled.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Make renesas_sdhi_sys_dmac.c a top-level module file that makes use of
library code supplied by renesas_sdhi_core.c
This is in order to facilitate adding other variants of SDHI;
in particular SDHI using different DMA controllers.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
[Arnd: Fixed module build error]
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Rename the source file SDHI. A follow-up patch will make it a library
file used by a different top-level module file.
The name "renesas" is chosen as the SDHI driver is applicable to a wider
range of SoCs than SH-Mobile it seems to be a more appropriate name.
However, the SDHI driver source itself, is left as sh_mobile_sdhi to
avoid unnecessary churn.
the name "core" was chosen to reflect the desired role of this file,
to provide core functionality to the sdhi driver. A follow-up patch will
move the file into that role.
Internal symbols have also been renamed to reflect the filename change.
The .name member of struct platform_driver and parameter to
MODULE_ALIAS() have not been changed in order to avoid the complication
of potentially breaking SH SoCs which still use platform drivers.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Rename the source file for DMA for SDHI as a follow-up to attaching
DMA code to the SDHI driver rather than the tmio_core driver.
The name "renesas" is chosen as the SDHI driver is applicable to a wider
range of SoCs than SH-Mobile it seems to be a more appropriate name.
However, the SDHI driver source itself, is left as sh_mobile_sdhi to
avoid unnecessary churn.
The name sys_dmac was chosen to reflect the type of DMA used.
Internal symbols have also been renamed to reflect the filename change.
A follow-up patch will re-organise the SDHI driver removing
the need for renesas_sdhi_get_dma_ops().
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Rename tmio_mmc_pio.c to tmio_mmc_core.c to more accurately reflect its
function: to provide core code for the tmio-mmc and sh-mobole-sdhi drivers.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Refactor DMA support to allow it to be provided by a set of call-backs
that are provided by a host driver. The motivation is to allow multiple
DMA implementations to be provided and instantiated at run-time.
Instantiate the existing DMA implementation from the sh_mobile_sdhi driver
which appears to match the current use-case. This has the side effect
of moving the DMA code from the tmio_core to the sh_mobile_sdhi driver.
A follow-up patch will change the source file for the SDHI DMA
implementation accordingly. Another follow-up patch will re-organise the
SDHI driver removing the need for tmio_mmc_get_dma_ops().
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reshuffle the comment at the top of the source
dropping filenames and moving up human readable strings.
This seems to be somewhat more useful information to start the
source file with. It is also less fragile, f.e. to file renames.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This reverts commit a6db2c8603 ("mmc: dw_mmc: Don't allow Runtime PM for
SDIO cards")'
As dw_mmc now is capable of preventing runtime PM suspend while SDIO IRQs
are enabled, let's drop the less fine-grained method, which is preventing
runtime PM suspend for all SDIO cards - no matter of whether SDIO IRQs are
being enabled or not.
In this way we don't keep the host runtime PM resumed, unless it's really
needed, thus avoiding to waste power.
Especially when SDIO IRQs is supported via a separate out-of-band IRQ line,
which isn't defined by the SDIO standard, typically the SDIO func driver
doesn't enable SDIO IRQs via sdio_claim_irq(). So, for these cases we can
now allow the dwmmc device to be runtime PM suspended in-between requests.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
To be able to handle SDIO IRQs the dw_mmc device needs to be powered and
providing clock to the SDIO card. Therefore, we must not allow the device
to be runtime PM suspended while SDIO IRQs are enabled.
To fix this, let's increase the runtime PM usage count while the mmc core
enables SDIO IRQs. Later when the mmc core tells dw_mmc to disable SDIO
IRQs, we drop the usage count to again allow runtime PM suspend.
This now becomes the default behaviour for dw_mmc. In cases where SDIO IRQs
can be re-routed as GPIO wake-ups during runtime PM suspend, one could
potentially allow runtime PM suspend. However, that will have to be
addressed as a separate change on top of this one.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Convert to use the more lightweight method for processing SDIO IRQs, which
involves the following changes:
- Enable MMC_CAP2_SDIO_IRQ_NOTHREAD when SDIO IRQ is supported and use
sdio_signal_irq() instead of mmc_signal_sdio_irq().
- Mask the SDIO IRQ before signaling a new one to be processed.
- Implement the ->ack_sdio_irq() callback to unmask the SDIO IRQ.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
For hosts not supporting MMC_CAP2_SDIO_IRQ_NOTHREAD but MMC_CAP_SDIO_IRQ,
the SDIO IRQs are processed from a dedicated kernel thread. For these
cases, the host calls mmc_signal_sdio_irq() from its ISR to signal a new
SDIO IRQ.
Signaling an SDIO IRQ makes the host's ->enable_sdio_irq() callback to be
invoked to temporary disable the IRQs, before the kernel thread is woken up
to process it. When processing of the IRQs are completed, they are
re-enabled by the kernel thread, again via invoking the host's
->enable_sdio_irq().
The observation from this, is that the execution path is being unnecessary
complex, as the host driver already knows that it needs to temporary
disable the IRQs before signaling a new one. Moreover, replacing the kernel
thread with a work/workqueue would not only greatly simplify the code, but
also make it more robust.
To address the above problems, let's continue to build upon the support for
MMC_CAP2_SDIO_IRQ_NOTHREAD, as it already implements SDIO IRQs to be
processed without using the clumsy kernel thread and without the ping-pong
calls of the host's ->enable_sdio_irq() callback for each processed IRQ.
Therefore, let's add new API sdio_signal_irq(), which enables hosts to
signal/process SDIO IRQs by using a work/workqueue, rather than using the
kernel thread.
Add also a new host callback ->ack_sdio_irq(), which the work invokes when
the SDIO IRQs have been processed. This informs the host about when it
shall re-enable the SDIO IRQs. Potentially, we could re-use the existing
->enable_sdio_irq() callback instead of adding a new one, however it has
turned out that it's more convenient for hosts to get this information via
a separate callback.
Hosts that wants to use this new method to signal/process SDIO IRQs, must
enable MMC_CAP2_SDIO_IRQ_NOTHREAD and implement the ->ack_sdio_irq()
callback.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
In cases when MMC_CAP2_SDIO_IRQ_NOTHREAD is set, there is a minor window
for when the mmc host could call sdio_run_irqs(), while in fact an SDIO
func driver could have decided to released the SDIO IRQ via a call to
sdio_release_irq(). In this scenario, processing of the SDIO IRQs are done
even if there is none IRQ claimed, which is not what we want.
To prevent this from happen, close the window by validating that at least
one SDIO IRQs is claimed, before deciding to process them.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
In case if a pwrseq-emmc has been bound to the host, a call to
mmc_power_up() triggers an eMMC HW reset via the pwrseq_emmc's
->post_power_on() callback. This isn't really what we want, as
mmc_power_up() is called each time when resuming the card.
As a matter of fact, the current approach may also violate the eMMC spec,
as the involved delays managed in pwrseq_emmc assumes both VCC and VCCQ has
been turned on, which isn't the case for VCCQ, unless the regulator is
always on.
Fix this behaviour by aligning to the same procedure used when the mmc host
implements the ->hw_reset() callback and has the MMC_CAP_HW_RESET flag set.
In this way the eMMC HW reset is issued at card detection scan, to cope
with bogus bootloaders and in the error recovery path via the mmc specific
bus_ops->reset() callback.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
The ->reset() callback is needed to implement a better support for eMMC HW
reset. The following changes will take advantage of the new callback.
Suggested-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Add the missing endianness conversions when printing the USB
device-descriptor idVendor and idProduct fields during probe.
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
AVR32 is gone. Now it's time to clean up the driver by removing
leftovers that was used by AVR32 related code.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
At the end of either of the read or write loops len is always zero
and hence the non-zero check on len and return of -EIO is redundant
and can be removed.
Detected by CoverityScan, CID#114293 ("Logically dead code")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
ret is signed however is printed as unsigned fix the same.
If printed as a negative number the result is easier to read.
No functional change.
Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The guid intel_dsm_guid does not need to be in global scope, so make it
static.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
There have been reports about SDIO failing with certain WiFi chips in
descriptor chain mode. SD / eMMC are working fine.
So let's fall back to bounce buffer mode for command SD_IO_RW_EXTENDED.
This was reported to fix the error.
Fixes: 79ed05e329 "mmc: meson-gx: add support for descriptor chain mode"
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Currently we use nornal Linux errno values in the block layer, and while
we accept any error a few have overloaded magic meanings. This patch
instead introduces a new blk_status_t value that holds block layer specific
status codes and explicitly explains their meaning. Helpers to convert from
and to the previous special meanings are provided for now, but I suspect
we want to get rid of them in the long run - those drivers that have a
errno input (e.g. networking) usually get errnos that don't know about
the special block layer overloads, and similarly returning them to userspace
will usually return somethings that strictly speaking isn't correct
for file system operations, but that's left as an exercise for later.
For now the set of errors is a very limited set that closely corresponds
to the previous overloaded errno values, but there is some low hanging
fruite to improve it.
blk_status_t (ab)uses the sparse __bitwise annotations to allow for sparse
typechecking, so that we can easily catch places passing the wrong values.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
acpi_evaluate_dsm() and friends take a pointer to a raw buffer of 16
bytes. Instead we convert them to use guid_t type. At the same time we
convert current users.
acpi_str_to_uuid() becomes useless after the conversion and it's safe to
get rid of it.
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Cc: Borislav Petkov <bp@suse.de>
Acked-by: Dan Williams <dan.j.williams@intel.com>
Cc: Amir Goldstein <amir73il@gmail.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Cc: Ben Skeggs <bskeggs@redhat.com>
Acked-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Joerg Roedel <jroedel@suse.de>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: Yisen Zhuang <yisen.zhuang@huawei.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Hikey board. Together with a couple of DTS updates for the Hikey board we have
also extended the mmc pwrseq_simple, to support a new power-off-delay-us DT
property, as that was required to enable a graceful power off sequence for the
WiFi chip.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=ECeh
-----END PGP SIGNATURE-----
Merge tag 'mmc-v4.12-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc
Pull MMC fixes from Ulf Hansson:
"This contains fixes to make the WiFi work again for the ARM64 Hikey
board.
Together with a couple of DTS updates for the Hikey board we have also
extended the mmc pwrseq_simple, to support a new power-off-delay-us DT
property, as that was required to enable a graceful power off sequence
for the WiFi chip"
* tag 'mmc-v4.12-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc:
arm64: dts: hikey: Fix WiFi support
arm64: dts: hi6220: Move board data from the dwmmc nodes to hikey dts
arm64: dts: hikey: Add the SYS_5V and the VDD_3V3 regulators
arm64: dts: hi6220: Move the fixed_5v_hub regulator to the hikey dts
arm64: dts: hikey: Add clock for the pmic mfd
mfd: dts: hi655x: Add clock binding for the pmic
mmc: pwrseq_simple: Parse DTS for the power-off-delay-us property
mmc: dt: pwrseq-simple: Invent power-off-delay-us
If the optional power-off-delay-us property is found, insert the
corresponding delay after asserting the GPIO during power off. This enables
a graceful shutdown sequence for some devices.
Cc: linux-mmc@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
The stingray SDHCI hardware supports ACMD12 and automatically
issues after multi block transfer completed.
If ACMD12 in SDHCI is disabled, spurious tx done interrupts are seen
on multi block read command with below error message:
Got data interrupt 0x00000002 even though no data
operation was in progress.
This patch uses SDHCI_QUIRK_MULTIBLOCK_READ_ACMD12 to enable
ACM12 support in SDHCI hardware and suppress spurious interrupt.
Signed-off-by: Srinath Mannam <srinath.mannam@broadcom.com>
Reviewed-by: Ray Jui <ray.jui@broadcom.com>
Reviewed-by: Scott Branden <scott.branden@broadcom.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Fixes: b580c52d58 ("mmc: sdhci-iproc: add IPROC SDHCI driver")
Cc: <stable@vger.kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
If the regulator probing is not yet finished this driver
might catch a -EPROBE_DEFER. Returning after this condition
did not remove the created platform device. On a repeated
call to the probe function the of_platform_device_create
fails.
Calling of_platform_device_destroy after EPROBE_DEFER resolves
this bug.
Signed-off-by: Jan Glauber <jglauber@cavium.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In case the DT specifies neither a regulator nor a gpio
for the shared power the driver will crash accessing the regulator.
Prevent the crash by checking the regulator before use.
Use mmc_regulator_get_supply() instead of open coding the same
logic.
Signed-off-by: Jan Glauber <jglauber@cavium.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Now that the JZ4740 and similar SoCs have a pinctrl driver, we rely on
the pins being properly configured before the driver probes.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The devm_gpiod_get_optional() function appends a "-gpios" to the
string passed to it, so if we want to find the "power-gpios" signal,
we must pass "power" to this function.
Fixes: 01d9584333 ("mmc: cavium: Add MMC support for Octeon SOCs.")
Signed-off-by: David Daney <david.daney@cavium.com>
[jglauber@cavium.com: removed point after subject line]
Signed-off-by: Jan Glauber <jglauber@cavium.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
OCTEON SoCs with CIU3 do not have interrupt masking local to the MMC
bus interface. Unfortunately, some even have a diagnostic register at
the same address of the enable register, which causes the interrupts
to fire immediately if stored to, thus breaking the driver. The proper
action on these SoCs is not to touch this register.
Fixes: 01d9584333 ("mmc: cavium: Add MMC support for Octeon SOCs.")
Signed-off-by: David Daney <david.daney@cavium.com>
[jglauber@cavium.com: removed point after subject line]
Signed-off-by: Jan Glauber <jglauber@cavium.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Currently, the xenon_clean_phy() is only used for freeing phy_params.
The phy_params is allocated by devm_kzalloc(), there's no need to free
is explicitly.
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Acked-by: Hu Ziji <huziji@marvell.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
-----BEGIN PGP SIGNATURE-----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=lbS7
-----END PGP SIGNATURE-----
Merge tag 'hwparam-20170420' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs
Pull hw lockdown support from David Howells:
"Annotation of module parameters that configure hardware resources
including ioports, iomem addresses, irq lines and dma channels.
This allows a future patch to prohibit the use of such module
parameters to prevent that hardware from being abused to gain access
to the running kernel image as part of locking the kernel down under
UEFI secure boot conditions.
Annotations are made by changing:
module_param(n, t, p)
module_param_named(n, v, t, p)
module_param_array(n, t, m, p)
to:
module_param_hw(n, t, hwtype, p)
module_param_hw_named(n, v, t, hwtype, p)
module_param_hw_array(n, t, hwtype, m, p)
where the module parameter refers to a hardware setting
hwtype specifies the type of the resource being configured. This can
be one of:
ioport Module parameter configures an I/O port
iomem Module parameter configures an I/O mem address
ioport_or_iomem Module parameter could be either (runtime set)
irq Module parameter configures an I/O port
dma Module parameter configures a DMA channel
dma_addr Module parameter configures a DMA buffer address
other Module parameter configures some other value
Note that the hwtype is compile checked, but not currently stored (the
lockdown code probably won't require it). It is, however, there for
future use.
A bonus is that the hwtype can also be used for grepping.
The intention is for the kernel to ignore or reject attempts to set
annotated module parameters if lockdown is enabled. This applies to
options passed on the boot command line, passed to insmod/modprobe or
direct twiddling in /sys/module/ parameter files.
The module initialisation then needs to handle the parameter not being
set, by (1) giving an error, (2) probing for a value or (3) using a
reasonable default.
What I can't do is just reject a module out of hand because it may
take a hardware setting in the module parameters. Some important
modules, some ipmi stuff for instance, both probe for hardware and
allow hardware to be manually specified; if the driver is aborts with
any error, you don't get any ipmi hardware.
Further, trying to do this entirely in the module initialisation code
doesn't protect against sysfs twiddling.
[!] Note that in and of itself, this series of patches should have no
effect on the the size of the kernel or code execution - that is
left to a patch in the next series to effect. It does mark
annotated kernel parameters with a KERNEL_PARAM_FL_HWPARAM flag in
an already existing field"
* tag 'hwparam-20170420' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs: (38 commits)
Annotate hardware config module parameters in sound/pci/
Annotate hardware config module parameters in sound/oss/
Annotate hardware config module parameters in sound/isa/
Annotate hardware config module parameters in sound/drivers/
Annotate hardware config module parameters in fs/pstore/
Annotate hardware config module parameters in drivers/watchdog/
Annotate hardware config module parameters in drivers/video/
Annotate hardware config module parameters in drivers/tty/
Annotate hardware config module parameters in drivers/staging/vme/
Annotate hardware config module parameters in drivers/staging/speakup/
Annotate hardware config module parameters in drivers/staging/media/
Annotate hardware config module parameters in drivers/scsi/
Annotate hardware config module parameters in drivers/pcmcia/
Annotate hardware config module parameters in drivers/pci/hotplug/
Annotate hardware config module parameters in drivers/parport/
Annotate hardware config module parameters in drivers/net/wireless/
Annotate hardware config module parameters in drivers/net/wan/
Annotate hardware config module parameters in drivers/net/irda/
Annotate hardware config module parameters in drivers/net/hamradio/
Annotate hardware config module parameters in drivers/net/ethernet/
...
- Continue to re-factor code to prepare for eMMC CMDQ and blkmq support
- Introduce queue semantics to prepare for eMMC CMDQ and blkmq support
- Add helper functions to manage temporary enable/disable of eMMC CMDQ
- Improve wait-busy detection for SDIO
MMC host:
- cavium: Add driver to support Cavium controllers
- cavium: Extend Cavium driver to support Octeon SOCs and ThunderX SOCs
- bcm2835: Add new driver for Broadcom BCM2835 controller
- sdhci-xenon: Add driver to support Marvell Xenon SDHCI controller
- sdhci-tegra: Add support for the Tegra186 variant
- sdhci-of-esdhc: Support for UHS-I SD cards
- sdhci-of-esdhc: Support for eMMC HS200 cards
- sdhci-cadence: Add eMMC HS400 enhanced strobe support
- sdhci-esdhc-imx: Reset tuning circuit when needed
- sdhci-pci: Modernize and clean-up some PM related code
- sdhci-pci: Avoid re-tuning at runtime PM for some Intel devices
- sdhci-pci|acpi: Use aggressive PM for some Intel BYT controllers
- sdhci: Re-factoring and modernizations
- sdhci: Optimize delay loops
- sdhci: Improve register dump print format
- sdhci: Add support for the Command Queue Engine
- meson-gx: Various improvements and clean-ups
- meson-gx: Add support for CMD23
- meson-gx: Basic tuning support to avoid CRC errors
- s3cmci: Enable probing via DT
- mediatek: Improve tuning support for eMMC HS200 and HS400 mode
- tmio: Improve DMA support
- tmio: Use correct response for CMD12
- dw_mmc: Minor improvements and clean-ups
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=p+Hb
-----END PGP SIGNATURE-----
Merge tag 'mmc-v4.12' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc
Pull MMC updates from Ulf Hansson:
"MMC core:
- Continue to re-factor code to prepare for eMMC CMDQ and blkmq support
- Introduce queue semantics to prepare for eMMC CMDQ and blkmq support
- Add helper functions to manage temporary enable/disable of eMMC CMDQ
- Improve wait-busy detection for SDIO
MMC host:
- cavium: Add driver to support Cavium controllers
- cavium: Extend Cavium driver to support Octeon and ThunderX SOCs
- bcm2835: Add new driver for Broadcom BCM2835 controller
- sdhci-xenon: Add driver to support Marvell Xenon SDHCI controller
- sdhci-tegra: Add support for the Tegra186 variant
- sdhci-of-esdhc: Support for UHS-I SD cards
- sdhci-of-esdhc: Support for eMMC HS200 cards
- sdhci-cadence: Add eMMC HS400 enhanced strobe support
- sdhci-esdhc-imx: Reset tuning circuit when needed
- sdhci-pci: Modernize and clean-up some PM related code
- sdhci-pci: Avoid re-tuning at runtime PM for some Intel devices
- sdhci-pci|acpi: Use aggressive PM for some Intel BYT controllers
- sdhci: Re-factoring and modernizations
- sdhci: Optimize delay loops
- sdhci: Improve register dump print format
- sdhci: Add support for the Command Queue Engine
- meson-gx: Various improvements and clean-ups
- meson-gx: Add support for CMD23
- meson-gx: Basic tuning support to avoid CRC errors
- s3cmci: Enable probing via DT
- mediatek: Improve tuning support for eMMC HS200 and HS400 mode
- tmio: Improve DMA support
- tmio: Use correct response for CMD12
- dw_mmc: Minor improvements and clean-ups"
* tag 'mmc-v4.12' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc: (148 commits)
mmc: sdhci-of-esdhc: limit SD clock for ls1012a/ls1046a
mmc: sdhci-of-esdhc: poll ESDHC_CLOCK_STABLE bit with udelay
mmc: sdhci-xenon: Fix default value of LOGIC_TIMING_ADJUST for eMMC5.0 PHY
mmc: sdhci-xenon: Fix the work flow in xenon_remove().
MIPS: Octeon: cavium_octeon_defconfig: Enable Octeon MMC
mmc: sdhci-xenon: Remove redundant dev_err call in get_dt_pad_ctrl_data()
mmc: cavium: Use module_pci_driver to simplify the code
mmc: cavium: Add MMC support for Octeon SOCs.
mmc: cavium: Fix detection of block or byte addressing.
mmc: core: Export API to allow hosts to get the card address
mmc: sdio: Fix sdio wait busy implement limitation
mmc: sdhci-esdhc-imx: reset tuning circuit when power on mmc card
clk: apn806: fix spelling mistake: "mising" -> "missing"
mmc: sdhci-of-esdhc: add delay between tuning cycles
mmc: sdhci: Control the delay between tuning commands
mmc: sdhci-of-esdhc: add tuning support
mmc: sdhci-of-esdhc: add support for signal voltage switch
mmc: sdhci-of-esdhc: add peripheral clock support
mmc: sdhci-pci: Allow for 3 bytes from Intel DSM
mmc: cavium: Fix a shift wrapping bug
...
Pull block layer updates from Jens Axboe:
- Add BFQ IO scheduler under the new blk-mq scheduling framework. BFQ
was initially a fork of CFQ, but subsequently changed to implement
fairness based on B-WF2Q+, a modified variant of WF2Q. BFQ is meant
to be used on desktop type single drives, providing good fairness.
From Paolo.
- Add Kyber IO scheduler. This is a full multiqueue aware scheduler,
using a scalable token based algorithm that throttles IO based on
live completion IO stats, similary to blk-wbt. From Omar.
- A series from Jan, moving users to separately allocated backing
devices. This continues the work of separating backing device life
times, solving various problems with hot removal.
- A series of updates for lightnvm, mostly from Javier. Includes a
'pblk' target that exposes an open channel SSD as a physical block
device.
- A series of fixes and improvements for nbd from Josef.
- A series from Omar, removing queue sharing between devices on mostly
legacy drivers. This helps us clean up other bits, if we know that a
queue only has a single device backing. This has been overdue for
more than a decade.
- Fixes for the blk-stats, and improvements to unify the stats and user
windows. This both improves blk-wbt, and enables other users to
register a need to receive IO stats for a device. From Omar.
- blk-throttle improvements from Shaohua. This provides a scalable
framework for implementing scalable priotization - particularly for
blk-mq, but applicable to any type of block device. The interface is
marked experimental for now.
- Bucketized IO stats for IO polling from Stephen Bates. This improves
efficiency of polled workloads in the presence of mixed block size
IO.
- A few fixes for opal, from Scott.
- A few pulls for NVMe, including a lot of fixes for NVMe-over-fabrics.
From a variety of folks, mostly Sagi and James Smart.
- A series from Bart, improving our exposed info and capabilities from
the blk-mq debugfs support.
- A series from Christoph, cleaning up how handle WRITE_ZEROES.
- A series from Christoph, cleaning up the block layer handling of how
we track errors in a request. On top of being a nice cleanup, it also
shrinks the size of struct request a bit.
- Removal of mg_disk and hd (sorry Linus) by Christoph. The former was
never used by platforms, and the latter has outlived it's usefulness.
- Various little bug fixes and cleanups from a wide variety of folks.
* 'for-4.12/block' of git://git.kernel.dk/linux-block: (329 commits)
block: hide badblocks attribute by default
blk-mq: unify hctx delay_work and run_work
block: add kblock_mod_delayed_work_on()
blk-mq: unify hctx delayed_run_work and run_work
nbd: fix use after free on module unload
MAINTAINERS: bfq: Add Paolo as maintainer for the BFQ I/O scheduler
blk-mq-sched: alloate reserved tags out of normal pool
mtip32xx: use runtime tag to initialize command header
scsi: Implement blk_mq_ops.show_rq()
blk-mq: Add blk_mq_ops.show_rq()
blk-mq: Show operation, cmd_flags and rq_flags names
blk-mq: Make blk_flags_show() callers append a newline character
blk-mq: Move the "state" debugfs attribute one level down
blk-mq: Unregister debugfs attributes earlier
blk-mq: Only unregister hctxs for which registration succeeded
blk-mq-debugfs: Rename functions for registering and unregistering the mq directory
blk-mq: Let blk_mq_debugfs_register() look up the queue name
blk-mq: Register <dev>/queue/mq after having registered <dev>/queue
ide-pm: always pass 0 error to ide_complete_rq in ide_do_devset
ide-pm: always pass 0 error to __blk_end_request_all
..
The ls1046a datasheet specified that the max SD clock frequency
for eSDHC SDR104/HS200 was 167MHz, and the ls1012a datasheet
specified it's 125MHz for ls1012a. So this patch is to add the
limitation.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The loop to poll ESDHC_CLOCK_STABLE bit with mdelay would waste time
because the time to stabilize is much less than 1 ms. This patch is
to use udelay instead to avoid time wasting.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The default value of LOGIC_TIMING_ADJUST register in eMMC 5.0 PHY is
different from that in eMMC 5.1 PHY. Set the specific value for that
register in eMMC 5.0 PHY.
Signed-off-by: Hu Ziji <huziji@marvell.com>
Reported-by: Jisheng Zhang <jszhang@marvell.com>
Tested-by: Jisheng Zhang <jszhang@marvell.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
sdhci_remove_host() might execute SOFT_RESET_ALL. Inside xenon_remove(),
Xenon SDHC should be enabled during sdhci_remove_host().
Move xenon_sdhc_unprepare after sdhci_remove_host() such that Xenon SDHC is
disabled after sdhci_remove_host() completes.
Signed-off-by: Hu Ziji <huziji@marvell.com>
Reported-by: Jisheng Zhang <jszhang@marvell.com>
Tested-by: Jisheng Zhang <jszhang@marvell.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
There is a error message within devm_ioremap_resource
already, so remove the dev_err call to avoid redundant
error message.
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Use the module_pci_driver() macro to make the code simpler
by eliminating module_init and module_exit calls.
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-by: Jan Glauber <jglauber@cavium.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add platform driver for Octeon SOCs.
Signed-off-by: Steven J. Hill <Steven.Hill@cavium.com>
Signed-off-by: David Daney <david.daney@cavium.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Use the mmc_card_is_blockaddr() function to properly detect if the
card uses byte or block addressing.
Signed-off-by: Steven J. Hill <Steven.Hill@cavium.com>
Acked-by: David Daney <david.daney@cavium.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Some hosts controllers, like Cavium, needs to know whether the card
operates in byte- or block-address mode. Therefore export a new API,
mmc_card_is_blockaddr(), which provides this information.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Steven J. Hill <Steven.Hill@cavium.com>
Acked-by: David Daney <david.daney@cavium.com>
The host may issue an I/O abort by writing to the CCCR at any time
during I/O read operation via CMD52. And host may need suspend
transcation during write busy stage in SDIO suspend/resume scenario.
>From other side, a card may accept CMD52 during data transfer phase.
Previous implement would block issuing above command in busy stage.
It cause function driver can't implement as proper way and has no
opportunity to do some coverage in error case via I/O abort etc.
We need bypass some necessary operation during busy check stage.
Signed-off-by: Jiajie Hao <jiajie.hao@mediatek.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
USDHC tuning circuit should be reset before every time card enumeration
or re-enumeration.
SD3.0 card need tuning. For SDR104 card, when system suspend in standby
mode, and then resume back, the IO timing is still SDR104(tuned) which
may result in card re-enumeration fail in low card speed(400khz) for some
cards. And we did meet the issue that in certain probability, SDR104
card meet mmc command CRC/Timeout error when send CMD2 during mmc bus
resume.
This patch reset the tuning circuit when the ios timing is
MMC_TIMING_LEGACY/MMC_TIMING_MMC_HS/MMC_TIMING_SD_HS, which means both
mmc_power_up() and mmc_power_off() will reset the tuning circuit.
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Acked-by: Dong Aisheng <aisheng.dong@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
It's observed that eSDHC needed delay between tuning cycles for
HS200 successful tuning. This patch is to set 1ms delay for that.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The delay between tuning commands for SD cards is not part of the
specification. A driver that needs it probably needs it for eMMC
too, whereas most drivers would probably like to set it to 0. Make
it a host member (host->tuning_delay) that defaults to the existing
behaviour. Drivers can set it to zero to eliminate the delay, or
set it to a positive value to always have a delay.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
eSDHC uses tuning block for tuning procedure. So the tuning
block control register must be configured properly before tuning.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
eSDHC supports signal voltage switch from 3.3v to 1.8v by
eSDHC_PROCTL[VOLT_SEL] bit. This bit changes the value of output
signal SDHC_VS, and there must be a control circuit out of eSDHC
to change the signal voltage according to SDHC_VS output signal.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
eSDHC could select peripheral clock or platform clock as clock source by
the PCS bit of eSDHC Control Register, and this bit couldn't be reset by
software reset for all. In default, the platform clock is used. But we have
to use peripheral clock since it has a higher frequency to support eMMC
HS200 mode and SD UHS-I mode. This patch is to add peripheral clock support
and use it instead of platform clock if it's declared in eSDHC dts node.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The DSM used by some Intel controllers can return a 3 byte package. Allow
for that by using memcpy to copy the bytes.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
"dat" is a u64 and "shift" starts as 54 so this is a shift wrapping bug.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add a pointer check to prevent this smatch warning:
drivers/mmc/host/cavium.c:803 cvm_mmc_request()
error: we previously assumed 'cmd->data' could be null (see line 782)
This is a theoretical fix because MMC_CMD_ADTC seems to imply
that cmd->data is not null. Nevertheless checking cmd->data
before using it improves readability.
Signed-off-by: Jan Glauber <jglauber@cavium.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
So far a bounce buffer is used to serialize the scatterlist(s).
This overhead can be avoided by switching to descriptor chain mode.
As result the performance is drastically improved. On a Odroid-C2 with
a 128 GB eMMC module raw reads reach 140 MB/s.
Prerequisite for descriptor chain mode is that all scatterlist buffers
are 8 byte aligned for 64-bit DMA. That's not always the case, at least
the brcmfmac SDIO WiFi driver is known to cause problems.
Therefore, for each request, check upfront whether all scatterlist
buffers are 8 byte aligned and fall back to bounce buffer mode if
that's not the case.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch adds basic tuning which changes the rx clock phase only
until a working setting is found.
On a Odroid C2 with 128GB eMMC card and 200 MHz MMC clock only
180° rx clock phase make the system boot w/o CRC errors.
With other MMC devices / clock speeds this might be different,
therefore don't change the driver config in general.
When retuning skip the currently active parameter set. This avoids
the current problematic config to be chosen again if it causes CRC
errors just occasionally.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Introduce struct meson_tuning_params for storing the clock phase
configurations. There's no functional change because tx and rx
clock phase were implicitely set to CLK_PHASE_0 before.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Annotate big endian values correctly and make sparse happy.
In mmc_app_send_scr remove scr function parameter as it was
updating card->raw_scr anyway.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
devm_pinctrl_get() returns error pointers, it never returns NULL.
Fixes: 455e5cd6f7 ("mmc: omap_hsmmc: Pin remux workaround to support SDIO interrupt on AM335x")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Some SoCs have PHY PAD outside Xenon IP.
PHY PAD voltage should match signalling voltage in use.
Add generic SoC PHY PAD voltage control interface.
Implement Aramda-3700 SoC PHY PAD voltage control.
Signed-off-by: Hu Ziji <huziji@marvell.com>
Tested-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Marvell Xenon eMMC/SD/SDIO Host Controller contains PHY.
Multiple types of PHYs are supported.
Add support to multiple types of PHYs init and configuration.
Add register definitions of PHYs.
Xenon PHY cannot fit in kernel common PHY framework.
Xenon SDHC PHY register is a part of Xenon SDHC register set.
Besides, MMC initialization has to call several PHY functions to
complete timing setting.
Those PHY setting functions have to access SDHC registers and know
current MMC setting, such as bus width, clock frequency and
speed mode.
As a result, implement Xenon PHY in MMC host directory.
Signed-off-by: Hu Ziji <huziji@marvell.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add Xenon eMMC/SD/SDIO host controller core functionality.
Add Xenon specific initialization process.
Add Xenon specific mmc_host_ops APIs.
Add Xenon specific register definitions.
Add CONFIG_MMC_SDHCI_XENON support in drivers/mmc/host/Kconfig.
Marvell Xenon SDHC conforms to SD Physical Layer Specification
Version 3.01 and is designed according to the guidelines provided
in the SD Host Controller Standard Specification Version 3.00.
Signed-off-by: Hu Ziji <huziji@marvell.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Export sdhci_start_signal_voltage_switch() from sdhci.c.
Thus vendor sdhci driver can implement its own signal voltage
switch routine.
Signed-off-by: Hu Ziji <huziji@marvell.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Export sdhci_set_ios() in sdhci.c.
Thus vendor sdhci driver can implement its own set_ios() routine.
Signed-off-by: Hu Ziji <huziji@marvell.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add support for switching to DDR mode for eMMC devices.
Signed-off-by: Jan Glauber <jglauber@cavium.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add Support for the scatter-gather DMA available in the
ThunderX MMC units. Up to 16 DMA requests can be processed
together.
Signed-off-by: Jan Glauber <jglauber@cavium.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Matthias Kraemer
Benoît Thébaudeau
Phong LE
Gustavo A. R. Silva
Wolfram Sang
David Woods
Fabio Estevam
Wu Fengguang
Ulf Hansson
Linus Walleij
Markus Elfring
Simon Horman
Johan Hovold
Andy Shevchenko
Colin Ian King
Shubhrajyoti Datta
Christoph Hellwig
Heiner Kallweit
Linus Torvalds
Srinath Mannam
Jan Glauber
Paul Cercueil
David Daney
Jisheng Zhang
yangbo lu
Hu Ziji
Wei Yongjun
Steven J. Hill
jiajie.hao@mediatek.com
Haibo Chen
Adrian Hunter
Dan Carpenter
Winkler, Tomas
Piotr Sroka