This checks if the DMA address is bigger than what the controller can manage.
It will reallocate the buffers in the GFP_DMA zone in that case.
The patch by Michael Buesch has been ported to b43legacy.
Thanks to Matti Viljanen for reporting this.
Cc: Matti Viljanen <viljanen.matti@gmail.com>
Signed-off-by: Stefano Brivio <stefano.brivio@polimi.it>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Value of count is used to decide when to replenish rx buffers. If it is
equal or above 8 we replenish the buffers. Ensure there is no starvation
by initializing count to 8 - thus forcing replenish at first iteration.
This is helpful when rx receives batches of buffers smaller than 8.
Signed-off-by: Mohamed Abbas <mabbas@linux.intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch prevents sending host commands when rfkill is on
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The geos information is set up during probe and should only
be removed during pci_remove, not during _down.
This is a temporary fix until the setting of the status bits
have been cleaned up (to explicitly match all setting with
clearing of status bits).
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Enable workaround for poor link stalls by link quality instead of link
speed. Using link speed caused workaround be active always on 802.11b
networks which reduced performance and not even catch all stalls.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
when setting up the tx descriptors for the hardware we must account for any
padding between the header and the data we might have added previously. frame
len is the length of the frame in the air (including FCS but no padding) and
buffer len is the length of the buffer (including padding, but without FCS).
changing the way ah_setup_tx_desc is called: now excluding the FCS, since it's
easier to add that in the function where we need it.
before this fix we sent trailing zero bytes after the packet (because frame len
included the padding) which was not a big problem without WEP, but with WEP
this resultes in a wrong WEP checksum and the packet is discarded - which is
how i noticed at all ;)
an easy way to run into header padding problems, btw, is to connect to a QoS
(WME) enabled access point (eg. madwifi) - QoS data frames are 2 byte longer
and will require padding.
this patch applies on top of luis latest patch series from 04.02.2008.
drivers/net/wireless/ath5k/base.c: Changes-licensed-under: 3-Clause-BSD
drivers/net/wireless/ath5k/hw.c: Changes-licensed-under: ISC
Signed-off-by: Bruno Randolf <bruno@thinktube.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
With assists from Russell King <rmk+kernel@arm.linux.org.uk> and
Andrew Morton <akpm@linux-foundation.org>...
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Users reported that ARP's were lost with e1000e. The problem
is fixed by not enabling this manageability configuration
bit.
None of the release_manageability code is actually needed as the
normal device reset during a shutdown returns everthing to
the right condition automatically.
Signed-off-by: David Graham <david.graham@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Users reported that ARP's were lost with igb. The problem
is fixed by not enabling this manageability configuration
bit.
None of the release_manageability code is actually needed as the
normal device reset during a shutdown returns everthing to
the right condition automatically.
Signed-off-by: David Graham <david.graham@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
In reply to "RE: [Fwd: [PATCH 2.6.25] ixgbe/igb: correctly obtain protocol
information on transmit]" from Andy Gospodarek:
The driver was incorrectly looking at socket headers for
protocol information, needed for checksumming offload. Fix
this by not looking at the socket but frame headers instead.
This disregards extension headers but it's unclear that linux
generates those anyway.
Tested by Andy Gospodarek.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
CRC stripping was only correctly enabled for packet split recieves
which is used when receiving jumbo frames. Correctly enable SECRC
also for normal buffer packet receives.
Tested by Andy Gospodarek and Johan Andersson, see bugzilla #9940.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
According to one of OOPSes reported by Jann softirq can break
while skb is prepared for netif_rx. The report isn't complete,
so the real reason of the later bug could be different, but
IMHO this locking break in ax_bump is unsafe and unnecessary.
Reported-and-tested-by: Jann Traschewski <jann@gmx.de>
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Megahertz EM1144 PCMCIA ethernet adapter needs special handling
because it has two VERS_1 tuples and the station address is in
the second one. Conversion to generic handling of these fields
broke it. Reverting that fixes the device.
https://bugzilla.redhat.com/show_bug.cgi?id=233255
Thanks go to Jon Stanley for not giving up on this one until the
problem was found.
Signed-off-by: Chuck Ebbert <cebbert@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (82 commits)
[NET]: Make sure sockets implement splice_read
netconsole: avoid null pointer dereference at show_local_mac()
[IPV6]: Fix reversed local_df test in ip6_fragment
[XFRM]: Avoid bogus BUG() when throwing new policy away.
[AF_KEY]: Fix bug in spdadd
[NETFILTER] nf_conntrack_proto_tcp.c: Mistyped state corrected.
net: xfrm statistics depend on INET
[NETFILTER]: make secmark_tg_destroy() static
[INET]: Unexport inet_listen_wlock
[INET]: Unexport __inet_hash_connect
[NET]: Improve cache line coherency of ingress qdisc
[NET]: Fix race in dev_close(). (Bug 9750)
[IPSEC]: Fix bogus usage of u64 on input sequence number
[RTNETLINK]: Send a single notification on device state changes.
[NETLABLE]: Hide netlbl_unlabel_audit_addr6 under ifdef CONFIG_IPV6.
[NETLABEL]: Don't produce unused variables when IPv6 is off.
[NETLABEL]: Compilation for CONFIG_AUDIT=n case.
[GENETLINK]: Relax dances with genl_lock.
[NETLABEL]: Fix lookup logic of netlbl_domhsh_search_def.
[IPV6]: remove unused method declaration (net/ndisc.h).
...
The CRYPTO_DEV_HIFN_795X_RNG ifdefs are missing the CONFIG_ prefix.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This patch avoids a null pointer dereference when we read local_mac
for netconsole in configfs and shows default local mac address
value.
A null pointer dereference occurs when we call show_local_mac() via
local_mac entry in configfs before we setup the content of netpoll
using netpoll_setup().
Signed-off-by: Keiichi KII <k-keiichi@bx.jp.nec.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
HID: add USB IDs for MacBook 3rd generation
HID: add LCSPEC from VERNIER to quirk list
HID: fix processing of event quirks
HID: Blacklist new GTCO CalComp USB device PIDs
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6:
ACPI: DMI: quirk for FSC ESPRIMO Mobile V5505
ACPI: DMI blacklist updates
pnpacpi: __initdata is not an identifier
ACPI: static acpi_chain_head
ACPI: static acpi_find_dsdt_initrd()
ACPI: static acpi_no_initrd_override_setup()
thinkpad_acpi: static
ACPI suspend: Execute _WAK with the right argument
cpuidle: Add Documentation
ACPI, cpuidle: Clarify C-state description in sysfs
ACPI: fix suspend regression due to idle update
* git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6: (46 commits)
sh: Fix multiple UTLB hit on UP SH-4.
sh: fix pci io access for r2d boards
sh: fix ioreadN_rep and iowriteN_rep
sh: use ctrl_in/out for on chip pci access
sh: Kill off more dead symbols.
sh: __uncached_start only on sh32.
sh: asm/irq.h needs asm/cpu/irq.h.
serial: sh-sci: Fix up SH-5 build.
sh: Get SH-5 caches working again post-unification.
maple: Fix up maple build failure.
sh: Kill off bogus SH_SDK7780_STANDALONE symbol.
sh: asm/tlb.h needs linux/pagemap.h for CONFIG_SWAP=n.
sh: Tidy include/asm-sh/hp6xx.h
maple: improve detection of attached peripherals
sh: Shut up some trivial build warnings.
sh: Update SH-5 flush_cache_sigtramp() for API changes.
sh: Fix up set_fixmap_nocache() for SH-5.
sh: Fix up pte_mkhuge() build breakage for SH-5.
sh: Disable big endian for SH-5.
sh: Handle SH7366 CPU in check_bugs().
...
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
RDMA/cma: Do not issue MRA if user rejects connection request
mlx4_core: Move table_find from fmr_alloc to fmr_enable
IB/mlx4: mlx4_ib_fmr_alloc() should call mlx4_fmr_enable()
IPoIB: Remove unused struct ipoib_cm_tx.ibwc member
IPoIB: On P_Key change event, reset state properly
IB/mthca: Convert to use be16_add_cpu()
RDMA/cxgb3: Fail loopback connections
IB/cm: Fix infiniband_cm class kobject ref counting
IB/cm: Remove debug printk()s that snuck upstream
IB/mthca: Add missing sg_init_table() in mthca_map_user_db()
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc:
[POWERPC] Remove unused CONFIG_WANT_DEVICE_TREE
[POWERPC] Cell RAS: Remove DEBUG, and add license and copyright
[POWERPC] hvc_rtas_init() must be __init
[POWERPC] free_property() must not be __init
[POWERPC] vdso_do_func_patch{32,64}() must be __init
[POWERPC] Remove generated files on make clean
[POWERPC] Fix arch/ppc compilation - add typedef for pgtable_t
[POWERPC] Wire up new timerfd syscalls
[POWERPC] PS3: Update sys-manager button events
[POWERPC] PS3: Sys-manager code cleanup
[POWERPC] PS3: Use system reboot on restart
[POWERPC] PS3: Fix bootwrapper hang bug
[POWERPC] PS3: Fix reading pm interval in logical performance monitor
[POWERPC] PS3: Fix setting bookmark in logical performance monitor
[POWERPC] Fix DEBUG_PREEMPT warning when warning
d_path() is used on a <dentry,vfsmount> pair. Lets use a struct path to
reflect this.
[akpm@linux-foundation.org: fix build in mm/memory.c]
Signed-off-by: Jan Blunck <jblunck@suse.de>
Acked-by: Bryan Wu <bryan.wu@analog.com>
Acked-by: Christoph Hellwig <hch@infradead.org>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: "J. Bruce Fields" <bfields@fieldses.org>
Cc: Neil Brown <neilb@suse.de>
Cc: Michael Halcrow <mhalcrow@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
seq_path() is always called with a dentry and a vfsmount from a struct path.
Make seq_path() take it directly as an argument.
Signed-off-by: Jan Blunck <jblunck@suse.de>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: "J. Bruce Fields" <bfields@fieldses.org>
Cc: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
get_dcookie() is always called with a dentry and a vfsmount from a struct
path. Make get_dcookie() take it directly as an argument.
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Jan Blunck <jblunck@suse.de>
Acked-by: Christoph Hellwig <hch@infradead.org>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: "J. Bruce Fields" <bfields@fieldses.org>
Cc: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* Add path_put() functions for releasing a reference to the dentry and
vfsmount of a struct path in the right order
* Switch from path_release(nd) to path_put(&nd->path)
* Rename dput_path() to path_put_conditional()
[akpm@linux-foundation.org: fix cifs]
Signed-off-by: Jan Blunck <jblunck@suse.de>
Signed-off-by: Andreas Gruenbacher <agruen@suse.de>
Acked-by: Christoph Hellwig <hch@lst.de>
Cc: <linux-fsdevel@vger.kernel.org>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Steven French <sfrench@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is the central patch of a cleanup series. In most cases there is no good
reason why someone would want to use a dentry for itself. This series reflects
that fact and embeds a struct path into nameidata.
Together with the other patches of this series
- it enforced the correct order of getting/releasing the reference count on
<dentry,vfsmount> pairs
- it prepares the VFS for stacking support since it is essential to have a
struct path in every place where the stack can be traversed
- it reduces the overall code size:
without patch series:
text data bss dec hex filename
5321639 858418 715768 6895825 6938d1 vmlinux
with patch series:
text data bss dec hex filename
5320026 858418 715768 6894212 693284 vmlinux
This patch:
Switch from nd->{dentry,mnt} to nd->path.{dentry,mnt} everywhere.
[akpm@linux-foundation.org: coding-style fixes]
[akpm@linux-foundation.org: fix cifs]
[akpm@linux-foundation.org: fix smack]
Signed-off-by: Jan Blunck <jblunck@suse.de>
Signed-off-by: Andreas Gruenbacher <agruen@suse.de>
Acked-by: Christoph Hellwig <hch@lst.de>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Casey Schaufler <casey@schaufler-ca.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The sound drivers and the pnpbios core test for current->root != NULL. This
test seems to be unnecessary since we always have rootfs mounted before
initializing the drivers.
Signed-off-by: Jan Blunck <jblunck@suse.de>
Acked-by: Christoph Hellwig <hch@lst.de>
Cc: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: Jaroslav Kysela <perex@suse.cz>
Acked-by: Takashi Iwai <tiwai@suse.de>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The current pmac32_defconfig fails to build with the following error:
Building modules, stage 2.
ERROR: "check_media_bay" [drivers/block/swim3.ko] undefined!
WARNING: modpost: Found 23 section mismatch(es).
To see full details build your kernel with:
'make CONFIG_DEBUG_SECTION_MISMATCH=y'
make[2]: *** [__modpost] Error 1
This patch fixes that.
Signed-off-by: Tony Breeds <tony@bakeyournoodle.com>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Acked-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Cc: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There's an undesirable interaction with issuing MRA requests to
increase connection timeouts and the listen backlog.
When the rdma_cm receives a connection request, it queues an MRA with
the ib_cm. (The ib_cm will send an MRA if it receives a duplicate
REQ.) The rdma_cm will then create a new rdma_cm_id and give that to
the user, which in this case is the rdma_user_cm.
If the listen backlog maintained in the rdma_user_cm is full, it
destroys the rdma_cm_id, which in turns destroys the ib_cm_id. The
ib_cm_id generates a REJ because the state of the ib_cm_id has changed
to MRA sent, versus REQ received. When the backlog is full, we just
want to drop the REQ so that it is retried later.
Fix this by deferring queuing the MRA until after the user of the
rdma_cm has examined the connection request.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
mlx4_table_find (for FMR MPTs) requires that ICM memory already be
mapped. Before this fix, FMR allocation depended on ICM memory
already being mapped for the MPT entry. If all currently mapped
entries are taken, the find operation fails (even if the MPT ICM table
still had more entries, which were just not mapped yet).
This fix moves the mpt find operation to fmr_enable, to guarantee that
any required ICM memory mapping has already occurred.
Found by Oren Duer of Mellanox.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Currently mlx4_ib_fmr_alloc() calls mlx4_mr_enable() instead of
mlx4_fmr_enable(). The two functions are equivalent at the moment, but
this is not really correct (and the change is needed to fix a bug).
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
struct ipoib_cm_tx.ibwc is unused since commit 1b524963 ("IPoIB/cm:
Use common CQ for CM send completions"), so remove it.
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
In P_Key event handling, if the old P_Key is no longer available, the
driver must call ipoib_ib_dev_stop() -- just as it does when the P_Key
is still available (see procedure __ipoib_ib_dev_flush()).
When a P_Key becomes available, the driver will perform ipoib_open(),
which assumes that the QP is in RESET, the cm_id has been
destroyed/deleted, etc. If ipoib_ib_dev_stop() is not called as
described above, then these assumptions will be false, and the attempt
to bring the interface up will fail.
Found by Mellanox QA.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This fixes the following section mismatch:
<-- snip -->
...
WARNING: vmlinux.o(.text+0x2fbca8): Section mismatch in reference from the function .hvc_rtas_init() to the function .devinit.text:.hvc_alloc()
...
<-- snip -->
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
PS3 firmware 1.94 added the source of power and reset events to the
payload of the system manager POWER_PRESSED and RESET_PRESSED events.
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
General code cleanups for PS3 system-manager:
o Move all MODULE_ macros to bottom.
o Correct PS3_SM_WAKE_P_O_R value.
o Enhance comment on wakeup source values.
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The PS3 Other OS boot flag is not checked when an LPAR reboot is done,
so the ps3-boot-game-os utility fails to reboot the system into the
Game OS. This fix changes the PS3 restart handler from requesting an
PS3_SM_NEXT_OP_LPAR_REBOOT to requesting an PS3_SM_NEXT_OP_SYS_REBOOT.
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
ps3_read_pm (pm_interval) should return an actual HW register value
because the pm_interval register is a counter register.
This removes the shadow pm_interval register.
Signed-off-by: Takashi Yamamoto <TakashiA.Yamamoto@jp.sony.com>
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Fix the ps3_set_bookmark() routine of the PS3 logical performance
monitor driver.
To properly set a performance monitor bookmark the Cell processor
requires no instruction branches near the setting of the bookmark
SPR. Testing showed that the use of the db10cyc instruction did
not work correctly. This change replaces the db10cyc instruction
with 10 nop instructions.
Signed-off-by: Takashi Yamamoto <TakashiA.Yamamoto@jp.sony.com>
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Acer Extensa 5220 -- OSI(Linux) is a NOP
Dell OptiPlex 755 -- OSI(Linux) turns GUSB into a NOP
Dell PowerEdge 1950 -- OSI(Linux) is a NOP
Dell Precision 690 -- OSI(Linux) touches USB (skips GUSB)
FSC ESPRIMO Mobile V5505 -- OSI(Linux) is a NOP
Lenovo LENOVO3000 V100 -- OSI(Linux) is a NOP
Lenovo X61x -- OSI(Linux) enables Linux specific AML
Sony Vaio VGN-NR11S_S - OSI(Linux) is a NOP
Signed-off-by: Len Brown <len.brown@intel.com>
sparse complains at drivers/pnp/pnpacpi/core.c:39 with the error:
Trying to use reserved word '__attribute__' as identifier
Expected ) in function declarator, got ".init.data"
and at drivers/pnp/pnpacpi/core.c:49:38 with the error:
undefined identifier 'excluded_id_list'
With the patch below these sparse complaints do not occur
Signed-off-by: Roel Kluin <12o3l@tiscali.nl>
Signed-off-by: Len Brown <len.brown@intel.com>
The _WAK global ACPI control method has to be called with the
argument representing the sleep state being exited. Make it happen.
Special thanks to Mirco Tischler <mt-ml@gmx.de> for reporting the
problem and debugging.
Reported-by: Mirco Tischler <mt-ml@gmx.de>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
asm/hardware.h doesn't exist any more, and the definitions sh-sci.h
depended on are provided through asm/cpu/addrspace.h these days.
Kill off the bogus include.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Improve device detection for maple through longer delay
Experience suggests that a much longer delay in setting up the Maple bus
on the Dreamcast leads to better hardware detection.
Signed-off-by: Adrian McMenamin <adrian@mcmen.demon.co.uk>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds sh7366 cpu supports. Just the most basic things like interrupt
controller, clocks and serial port are included at this point.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Replacement second-in-series patch:
This patch fixes up memory leaks and, by delaying initialisation, makes
device detection more robust.
It also makes clearer the difference between struct maple_device and
struct device, as well as cleaning up the interrupt request code
(without changing its function in any way).
Also now removes redundant registration checking.
Signed-off-by: Adrian McMenamin <adrian@mcmen.demon.co.uk>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch is fundamentally about fixing up the whitespace problems
introduced by my previous patch (that brought the code into mainline). A
second patch will follow that will fix memory leaks. The two need to be
applied sequentially.
Signed-off-by: Adrian McMenamin <adrian@mcmen.demon.co.uk>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add a new sysfs entry under cpuidle states. desc - can be used by driver to
communicate to userspace any specific information about the state.
This helps in identifying the exact hardware C-states behind the ACPI C-state
definition.
Idea is to export this through powertop, which will help to map the C-state
reported by powertop to actual hardware C-state.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Earlier patch (bc71bec91f) broke
suspend resume on many laptops. The problem was reported by
Carlos R. Mafra and Calvin Walton, who bisected the issue to above patch.
The problem was because, C2 and C3 code were calling acpi_idle_enter_c1
directly, with C2 or C3 as state parameter, while suspend/resume was in
progress. The patch bc71bec started making use of that state information,
assuming that it would always be referring to C1 state. This caused the
problem with suspend-resume as we ended up using C2/C3 state indirectly.
Fix this by adding acpi_idle_suspend check in enter_c1.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
ipwireless (added by 099dc4fb62) is clearly
a net device:
drivers/built-in.o: In function `ipwireless_ppp_start_xmit':
/home/pmundt/devel/git/sh-2.6.25/drivers/char/pcmcia/ipwireless/network.c:165: undefined reference to `skb_under_panic'
/home/pmundt/devel/git/sh-2.6.25/drivers/char/pcmcia/ipwireless/network.c:165: undefined reference to `kfree_skb'
drivers/built-in.o: In function `ipwireless_network_packet_received':
/home/pmundt/devel/git/sh-2.6.25/drivers/char/pcmcia/ipwireless/network.c:377: undefined reference to `__alloc_skb'
/home/pmundt/devel/git/sh-2.6.25/drivers/char/pcmcia/ipwireless/network.c:377: undefined reference to `skb_over_panic'
drivers/built-in.o: In function `ppp_shutdown_interface':
/home/pmundt/devel/git/sh-2.6.25/drivers/net/ppp_generic.c:2517: undefined reference to `unregister_netdev'
/home/pmundt/devel/git/sh-2.6.25/drivers/net/ppp_generic.c:2517: undefined reference to `free_netdev'
[ ... and many more ... ]
select strikes again. ipwireless selects PPP which in turn tries to select
SLHC, both of which are technically "protected" by an if NETDEVICES
in drivers/net/Kconfig. This leads to .config hilarity, with net suddenly
ending up in the SCSI menu:
#
# SCSI device support
#
# CONFIG_SCSI_DMA is not set
# CONFIG_SCSI_NETLINK is not set
CONFIG_PPP=y
# CONFIG_PHONE is not set
Curiously the SLHC select from PPP doesn't seem to happen, as there's no
CONFIG_SLHC=y (only CONFIG_PPP=y gets set) -- Kconfig bug? Caught with a
randconfig.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Acked-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix section warning for parport_ECP_supported(); it's called from a routine
exported to modules, so it can't be removed with __devinit section pruning.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
All users are gone, remove definitions and comments referring
to them.
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Acked-by: David Howells <dhowells@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The raw_pci_read() interface (as the raw_pci_ops->read() before it)
unconditionally fills in a 32-bit integer return value regardless of the
size of the operation requested.
So claiming to take a "void *" is wrong, as is passing in a pointer to
just a byte variable.
Noticed by pageexec when enabling -fstack-protector (which needs other
patches too to actually work, but that's a separate issue).
Acked-by: Len Brown <len.brown@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
test_and_set_bit() on address of uint32_t is a Bad Idea(tm)...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
replace:
big_endian_variable = cpu_to_beX(beX_to_cpu(big_endian_variable) +
expression_in_cpu_byteorder);
with:
beX_add_cpu(&big_endian_variable, expression_in_cpu_byteorder);
Generated with a semantic patch.
Signed-off-by: Marcin Slusarz <marcin.slusarz@gmail.com>
Cc: Sean Hefty <sean.hefty@intel.com>
Cc: Hal Rosenstock <hal.rosenstock@gmail.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The cxgb3 HW and driver don't support loopback RDMA connections. So
fail any connection attempt where the destination address is local.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Fix compilation warning in gdth.c, which was using the deprecated
pci_find_device.
drivers/scsi/gdth.c:645: warning: 'pci_find_device' is deprecated (declared at include/linux/pci.h:495)
Changing it to use pci_get_device, instead.
Signed-off-by: Sergio Luis <sergio@larces.uece.br>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The patch: "gdth: switch to modern scsi host registration"
missed one simple fact when moving a way from scsi_module.c.
That is to call scsi_scan_host() on the probed host.
With this the gdth driver from 2.6.24 is again able to
see drives and boot.
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Tested-by: Joerg Dorchain <joerg@dorchain.net>
Tested-by: Stefan Priebe <s.priebe@allied-internet.ag>
Tested-by: Jon Chelton <jchelton@ffpglobal.com>
Cc: Stable Tree <stable@kernel.org>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Apparently these drivers now need uaccess.h
Signed-off-by: Robert Reif <reif@earthlink.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Arjan:
With the help of kerneloops.org I've spotted a nice little interaction
between the TTY layer and the bluetooth code, however the tty layer is not
something I'm all too familiar with so I rather ask than brute-force fix the
code incorrectly.
The raw details are at:
http://www.kerneloops.org/search.php?search=uart_flush_buffer
What happens is that, on closing the bluetooth tty, the tty layer goes
into the release_dev() function, which first does a bunch of stuff, then
sets the file->private_data to NULL, does some more stuff and then calls the
ldisc close function. Which in this case, is hci_uart_tty_close().
Now, hci_uart_tty_close() calls hci_uart_close() which clears some
internal bit, and then calls hci_uart_flush()... which calls back to the
tty layers' uart_flush_buffer() function. (in drivers/bluetooth/hci_tty.c
around line 194) Which then WARN_ON()'s because that's not allowed/supposed
to be called this late in the shutdown of the port....
Should the bluetooth driver even call this flush function at all??
David:
This seems to be what happens: Hci_uart_close() flushes using
hci_uart_flush(). Subsequently, in hci_dev_do_close(), (one step in
hci_unregister_dev()), hci_uart_flush() is called again. The comment in
uart_flush_buffer(), relating to the WARN_ON(), indicates you can't flush
after the port is closed; which sounds reasonable. I think hci_uart_close()
should set hdev->flush to NULL before returning. Hci_dev_do_close() does
check for this. The code path is rather involved and I'm not entirely clear
of all steps, but I think that's what should be done.
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 9af57b7a ("IB/cm: Add basic performance counters") introduced a
bug in how the reference count for cm_class.subsys.kobj was handled:
the path that released a device did a kobject_put() on that kobject, but
there was no kobject_get() in the path the handles adding a device. So
the reference count ended up too low, which leads to bad things. Fix up
and simplify the reference counting to avoid this.
(Actually, I introduced the bug when fixing the patch up to match some
of Greg's kobject changes, but who's counting)
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Usually harmless, since the scatterlist is always hard-coded to a length
of 1, but it triggers a BUG() if CONFIG_DEBUG_SG=y, so we better fix it.
This fixes <http://bugzilla.kernel.org/show_bug.cgi?id=9934>.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
It looks like there's been a bug in the module parameter setup forever.
The upshot doesn't really matter, because even if no parameters are ever
set, we just call sym53c416_setup() three times, but the zero values in
the arrays eventually cause nothing to happen. Unfortunately gcc has
started to notice this now too:
drivers/scsi/sym53c416.c: In function 'sym53c416_detect':
drivers/scsi/sym53c416.c:624: warning: the address of 'sym53c416' will always evaluate as 'true'
drivers/scsi/sym53c416.c:630: warning: the address of 'sym53c416_1' will always evaluate as 'true'
drivers/scsi/sym53c416.c:636: warning: the address of 'sym53c416_2' will always evaluate as 'true'
drivers/scsi/sym53c416.c:642: warning: the address of 'sym53c416_3' will always evaluate as 'true'
So fix this longstanding bug to keep gcc quiet.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Even if we don't want to register the WMI driver, we should initialize
the wmi_blocks list to be empty, since we don't want the wmi helper
functions to oops just because that basic list has not even been set up.
With this, "find_guid()" will happily return "not found" rather than
oopsing all over the place, and the callers will then just automatically
return false or AE_NOT_FOUND as appropriate.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'upstream-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
sata_mv: platform driver allocs dma without create
pata_ninja32: setup changes
pata_legacy: typo fix
pata_amd: Note in the module description it handles Nvidia
sata_mv: fix loop with last port
libata: ignore deverr on SETXFER if mode is configured
pata_via: fix SATA cable detection on cx700
Update lpfc driver version to 8.2.5
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Miscellaneous fixes:
- Fix ERRATT flag which was overlapping
- Allow RESTART mbx commands through when stopped.
- Accept incoming PLOGI when connected to an N_Port.
- Fix NPort to NPort pt2pt problems: ADISC and reg_vpi issues
- Fix vport unloading error that erroneously cleaned up RSCN buffers
- Fix memory leak during repeated unloads - in mbox handling
- Fix link bounce vs FLOGI race conditions
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Correct ndlp referencing issues:
- Fix ndlp kref issues due to race conditions between threads
- Fix cancel els delay retry event which missed an ndlp reference count
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Commit 313abe55 ("mlx4_core: For 64-bit systems, vmap() kernel queue
buffers") caused this to pop up on powerpc allyesconfig, looks like a
missing include file:
drivers/net/mlx4/alloc.c: In function 'mlx4_buf_alloc':
drivers/net/mlx4/alloc.c:162: error: implicit declaration of function 'vmap'
drivers/net/mlx4/alloc.c:162: error: 'VM_MAP' undeclared (first use in this function)
drivers/net/mlx4/alloc.c:162: error: (Each undeclared identifier is reported only once
drivers/net/mlx4/alloc.c:162: error: for each function it appears in.)
drivers/net/mlx4/alloc.c:162: warning: assignment makes pointer from integer without a cast
drivers/net/mlx4/alloc.c: In function 'mlx4_buf_free':
drivers/net/mlx4/alloc.c:187: error: implicit declaration of function 'vunmap'
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
It's easy to oversee this issue when working with this card
as evrything will work OK but performance is severely limited
(something like 1.5gbit on a x1 link) if the pci-express
slot does not offer more bandwidth.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
A logic mishap caused the adapter to keep link while we can
disable it due to WoL not being active, and vice versa.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
We're already starting to see reports from users still
using e1000 where they should be using e1000e now that this is
actually possible. Just to prevent some of this thrash, add
a big warning on load on these devices that people should
switch to e1000e.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add ethtool support to tsi108_eth network driver.
Signed-off-by: Alexandre Bounine <alexandreb@tundra.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Bug fix for tsi108_eth network driver.
This patch fixes a problem with link recovery after connection was lost.
Signed-off-by: Alexandre Bounine <alexandreb@tundra.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Code clean-up for tsi108_eth network driver.
This patch removes not needed dummy read and the corresponding comment.
The PHY logic requires two reads from the status register to get
current link status. This is done correctly inside mii_check_media().
Signed-off-by: Alexandre Bounine <alexandreb@tundra.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Bug fix for tsi108_eth network driver.
This patch fixes a problem with detection of 1000Mb speed.
Signed-off-by: Alexandre Bounine <alexandreb@tundra.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
include/scsi/scsi.h as a definition:
#define ABORT_TASK 0x0d
on the other hand drivers/scsi/aic94xx/aic94xx_sas.h has:
#define ABORT_TASK 0x03
rename the latter to SCB_ABORT_TASK
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
When the sata_mv driver is used as a platform driver,
mv_create_dma_pools() is never called so it fails when trying
to alloc in mv_pool_start().
Signed-off-by: Byron Bradley <byron.bbradley@gmail.com>
Acked-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Forcibly set more of the configuration at init time. This seems to fix at
least one problem reported. We don't know what most of these bits do, but
we do know what windows stuffs there.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Some controllers (VIA CX700) raise device error on SETXFER even after
mode configuration succeeded. Update ata_dev_set_mode() such that
device error is ignored if transfer mode is configured correctly. To
implement this, device is revalidated even after device error on
SETXFER.
This fixes kernel bugzilla bug 8563.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Use new scsi_eh_prep/restor_cmnd() for synchronous REQUEST_SENSE
invocation. This also converts the driver to the new accessor based
scatterlist implementation.
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Tested-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
fix leaking with scomp leaking when failing. Also free page10 on
driver removal and remove one extra space.
Signed-off-by: Yinghai Lu <yinghai.lu@sun.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Some sysfs problems reported. The serial number on late model
controllers was truncated. Non-DASD devices (tapes and CDROMs) were
showing up as JBOD in the level report on the physical channel.
Signed-off-by: Mark Salyzyn <aacraid@adaptec.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This patch modifies the I/O resource allocation behavior of FUSION
driver. The current version of driver allocates the I/O resources
even if they are not required and this creates trouble in low resource
environments. This driver now uses
pci_enable_device_mem/pci_enable_device functions to differentiate the
resource allocations.
Signed-off-by: Sathya Prakash <sathya.prakash@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The Adapter's Ignore Reset flag and insmod parameter boolean polarity
is incorrect in the driver.
Signed-off-by: Mark Salyzyn <aacraid@adaptec.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Added support for MSI utilizing the aacraid.msi=1 parameter. This
patch adds some localized or like-minded janitor fixes. Since the
default is disabled, there is no impact on the code paths unless the
customer wishes to experiment with the MSI performance.
Signed-off-by: Mark Salyzyn <aacraid@adaptec.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This patch sets the IOC pointer in drvrdata of pcidev before adding
the IOC into the list of IOCs. Without this patch the driver oops when
the mptsas and mptctl modules are loaded in parallel.
Signed-off-by: Sathya Prakash <sathya.prakash@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The MegaRAID driver's common management module (megaraid_mm.c) creates a
char device used by the management tool "megarc" from LSI Logic (and
possibly other management tools).
In 2.6 with udev, this device doesn't get created because it is not
registered in sysfs.
I first fixed this by registering a class "megaraid_mm", but realized that
this should probably be moved to misc devices, instead of taking up a char
major. This is because only 1 device is used, even if there are multiple
adapters - the minor is never used (the adapter info is in the ioctl block
sent to the driver, not detected based on the minor number as one might
think). So it is a complete waste to have an entire major taken by this.
So it now uses a misc device which I named "megadev0" (the name that megarc
expects), and has a dynamic minor (previoulsy a dynamic major was used).
I have tested this on my own system with the megarc tool, and it works just
as fine as before (only now the device gets created correctly by udev).
Acked-by: "Patro, Sumant" <Sumant.Patro@lsi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
struct asc_dvc_var needs overrun buffer to be placed on an 8 byte
boundary. advansys defines struct asc_dvc_var:
struct asc_dvc_var {
...
uchar overrun_buf[ASC_OVERRUN_BSIZE] __aligned(8);
The problem is that struct asc_dvc_var is placed on
shost->hostdata. So if the hostdata is not on an 8 byte boundary, the
advansys crashes. The hostdata is placed on a sizeof(unsigned long)
boundary so the 8 byte boundary is not garanteed with x86_32.
With 2.6.23 and 2.6.24, the hostdata is on an 8 byte boundary by
chance, but with the current git, it's not.
This patch removes overrun_buf static array and use kzalloc.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This patch fixes a use-after-free introduced by
commit a79d8e93d3 and spotted by the
Coverity checker.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Fix following warnings:
WARNING: drivers/net/sis190.o(.text+0x103): Section mismatch in reference from the function sis190_get_mac_addr() to the function .devinit.text:sis190_get_mac_addr_from_apc()
WARNING: drivers/net/sis190.o(.text+0x10e): Section mismatch in reference from the function sis190_get_mac_addr() to the function .devinit.text:sis190_get_mac_addr_from_eeprom()
Annotate sis190_get_mac_addr() with __devinit.
Signed-off-by: Sergio Luis <sergio@uece.br>
sis190.c | 3 ++-
1 file changed, 2 insertions(+), 1 deletion(-)
Signed-off-by: Jeff Garzik <jeff@garzik.org>
additional check of s390dbf level results in better performance
if the default low debugging level is active.
Signed-off-by: Peter Tiedemann <ptiedem@de.ibm.com>
Signed-off-by: Ursula Braun <braunu@de.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Since lcs makes use of 1 debug area only, the number of debug areas
is reduced, while the number of pages per area is increased.
Signed-off-by: Peter Tiedemann <ptiedem@de.ibm.com>
Signed-off-by: Ursula Braun <braunu@de.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Dummy NOP actions for fsm-statemachines have to be defined
separately for every using module of fsm-statemachines.
Thus the generic name fsm_action_nop is replaced by
module specific name netiucv_action_nop.
Signed-off-by: Ursula Braun <braunu@de.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Volatile variables queme_switch and pk_delay are not used anyway.
They are just a left over from an unused timer based packing logic.
Signed-off-by: Ursula Braun <braunu@de.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
New chipsets introduced variant Rx FIFO sizes that need to be taken into
account when setting up the tx pause watermarks. This patch introduces
the new device feature flags based on a version and implements the new
watermarks.
Signed-off-by: Ayaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch supports a new fix in hardware regarding tx collisions. In
the cases where we are in autoneg mode and the link partner is in forced
mode, we need to setup the tx deferral register differently in order to
reduce collisions on the wire.
Signed-off-by: Ayaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
When ARP completes due to a request rather than a reply the neighbor is
marked NUD_STALE instead of reachable (see arp_process()). The handler
for the resulting netevent needs to check also for NUD_STALE.
Failure to use the arp entry can cause RDMA connection failures.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Acked-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Show whether the MAC address was read from the EEPROM or
the onboard PAR registers.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Reading the ID register does not always return the correct ID
from the device, so we retry several times to see if we get
a correct value.
These failures seem to be excaserbated by the speed of the
access to the chip (possibly time between issuing the address
and then the data cycle).
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add entry to handle the MII ioctl() calls via the
generic_mii_ioctl call.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Allow the platform data to specify to the DM9000 driver
that there is no posibility of an attached EEPROM on the
device, so default all reads to 0xff and ignore any
write operations.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The writing of the data should implicitly truncate
the data to 8bits, so do not bother with the ands
in the code.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Remove the cal_CRC as this is basically wrappering the
ether_crc_le function, and is only being used by the
multicast hash table functions.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The code was using a delay of 8ms, when it should have been
using the EEPROM status flag from the device to indicate the
EEPROM transaction had finished.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Use the netif_msg_*() macros to enable the debugging based
on the board's msg_enable field. The output still goes via
the dev_dbg() macros, so will be tagged and output as
appropriate.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
We have a perfectly good version control system, so we do not
need to duplicate change comments in the header for this code.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Ensure we hold the spinlock whilst the registers and being
modified even though we hold the overall lock. This should
protect against an interrupt happening whilst we are using
the device.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Remove the old hack to program an initial EEPROM setting
into the DM9000 as we now have ethtool support for reading
and writing the EEPROM.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Allow the msg_enable value to be read and written by
the ethtool interface.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add ethtool support to access the configuration EEPROM
connected to the DM9000.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add a mutex to serialise access to the chip functions from
entries such as the ethtool and the MII code. This should
reduce the amount of time the spinlock is held to protect
the address register.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The srom array in the board data is only being used in the device probe
routines. The probe also only uses the first 6 bytes of an array
we spend 512ms reading 128 bytes from. Change to reading the
MAC area directly to the MAC address structure.
As a side product, we rename the read_srom_word to dm9000_read_eeprom
to bring it into line with the rest of the driver. No change is made
to the delay in this function, which will be dealt with in a later
patch.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
We can use sleeping functions when reading and writing the
PHY registers, so let us sleep instead of busy waiting for
the PHY.
Note, this also fixes a bug reading the PHY where only 100uS
was being used instead of 150uS
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The phy read and write routines call udelay() with the board
lock held, and with the posibility of IRQs being disabled. Since
these delays can be up to 500usec, and are only required as we
have to save the chip's address register.
To improve the behaviour, hold the lock whilst we are writing
and then restore the state before the delay and then repeat
the process once the delay has happened.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Remove the timer based MII phy polling, as this is
currently broken with the new EEPROM code that now
uses mutexes to protect the phy access.
This will need to be replaced in the future by some
form of mutex safe mechanism for reading the MII
phy status.
The replacement has not been done here as changing
this patch, which is early in the sequence has quite
a knock-on effect. Once this series is merged, then
a new presentation of an patch to poll the MII link
status can be added.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Use the flags in the IRQ resource to specify the type of
IRQ being requested, so that systems which do not have
level-based interrupts, or change the interrupt in some
other way can specify this without making an #ifdef mess
in the driver.
This is specifically designed to undo the change in commit
4e4fc05a2b which hardwires the
type for everyone but blackfin to IRQT_RISING, which breaks
all a number of Simtec boards which use (and setup in the
bootloader) active low IRQs.
Note, although there where originally objections due to
the use of IORESOURCE_IRQ and IRQT_ flags not sharing the
same definition, at least <include/linux/interrupt.h> notes
these are the same.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
CC: Daniel Mack <daniel@caiaq.de>
CC: Bryan Wu <bryan.wu@analog.com>
CC: Alex Landau <landau.alex@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Change the debug macros to use the compiler to elide any
unnecessary debug level, and to allow device configurable
debug control.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Move to using dev_dbg() and friends for the output of
information to the user.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Patch from: Laurent Pinchart <laurentp@cse-semaphore.com>
This patch adds a flag to the DM9000 platform data which, when set,
configures the device to use an external PHY.
Signed-off-by: Laurent Pinchart <laurentp@cse-semaphore.com>
Signed-off-by: Ben Dooks <ben-linuy@fluff.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Patch from: Laurent Pinchart <laurentp@cse-semaphore.com>
This patch splits the receive status in 8bit wide fields and convert the
packet length from little endian to CPU byte order.
Signed-off-by: Laurent Pinchart <laurentp@cse-semaphore.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
1. Add common code for stopping queue.
2. No need to call netif_stop_queue followed by netif_wake_queue (and
infact a netif_start_queue could have been used instead), instead
call stop_queue if required, and remove code under USE_GTS macro.
3. There is no need to check for netif_queue_stopped, as the network
core guarantees that for us (I am sure every driver could remove
that check, eg e1000 - I have tested that path a few billion times
with about a few hundred thousand qstops but the condition never
hit even once).
Signed-off-by: Krishna Kumar <krkumar2@in.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The e1000 driver stores the content of the PCI resources into
unsigned long's before ioremapping. This breaks on 32 bits
platforms that support 64 bits MMIO resources such as ppc 44x.
This fixes it by removing those temporary variables and passing
directly the result of pci_resource_start/len to ioremap.
The side effect is that I removed the assignments to the netdev
fields mem_start, mem_end and base_addr, which are totally useless
for PCI devices.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
--
drivers/net/e1000/e1000_main.c | 18 +++++-------------
1 file changed, 5 insertions(+), 13 deletions(-)
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Masakazu Mokuno <mokuno@sm.sony.co.jp>
Acked-by: Dan Williams <dcbw@redhat.com>
Acked-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add support for dual network (net_device) interface so that ethernet
and wireless can own separate ethX interfaces.
V2
- Fix the bug that bringing down and up the interface keeps rx
disabled.
- Make 'gelic_net_poll_controller()' extern , as David Woodhouse
pointed out at the previous submission.
- Fix weird usage of member names for the rx descriptor chain
V1
- Export functions which are convenient for both interfaces
- Move irq allocation/release code to driver probe/remove handlers
because interfaces share interrupts.
- Allocate skbs by using dev_alloc_skb() instead of netdev_alloc_skb()
as the interfaces share the hardware rx queue.
- Add gelic_port struct in order to abstract dual interface handling
- Change handlers for hardware queues so that they can handle dual
{source,destination} interfaces.
- Use new NAPI functions
This is a prerequisite for the new PS3 wireless support.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add support for interrupt driven port link status detection.
Signed-off-by: Masakazu Mokuno <mokuno@sm.sony.co.jp>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Remove some ethtool handlers, which duplicate functionality that was already
provided by the common ethtool handlers.
Signed-off-by: Masakazu Mokuno <mokuno@sm.sony.co.jp>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Code cleanup:
- Use appropriate prefixes for names instead of fixed 'gelic_net'
so that objects of the functions, variables and constants can be estimated.
- Remove definitions for IPSec offload to the gelic hardware. This
functionality is never supported on PS3.
- Group constants with enum.
- Use bitwise constants for interrupt status, instead of bit numbers to
eliminate shift operations.
- Style fixes.
Signed-off-by: Masakazu Mokuno <mokuno@sm.sony.co.jp>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Mark the members of the structure for DMA descriptors with proper endian
annotations and use the appropriate accessor macros.
As the gelic driver works only on PS3, all these macros will be
expanded to null.
Signed-off-by: Masakazu Mokuno <mokuno@sm.sony.co.jp>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The device id for lv1_net_set_interrupt_status_indicator() is wrong.
This path would be invoked only in the case of an initialization failure.
Signed-off-by: Masakazu Mokuno <mokuno@sm.sony.co.jp>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Updates the 8139too driver to work with recently added
(a724605cb7) declared coherent memory
patch for the Dreamcast.
Signed-off-by: Adrian McMenamin <adrian@mcmen.demon.co.uk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
To kill the volatiles also switch it to stop poking ISA memory directly
without going through readb and friends.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Change hard coded 2 to NET_IP_ALIGN. Added new #define with comments.
Tested amd_64
Signed-off-by: Don Fry <pcnet32@verizon.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
We need to blacklist this device, as it should be handled by
ldusb driver.
Reported-by: stephen <stephen.ware@eqware.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The old code (before move) stopped further processing of the
event after it has been already processed by the quirk handler.
The new code didn't propagate the return value properly, and
therefore the processing always proceeded, which was wrong.
This patch fixes it. Pointed out in kernel.org bugzilla #9842
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Adds new GTCO CalComp USB device PIDs to the blacklist.
Signed-off-by: Jeremy A. Roberson <jroberson@gtcocalcomp.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
commit 813a0eb233
Author: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Date: Fri Jan 25 22:17:10 2008 +0100
ide: switch idedisk_prepare_flush() to use REQ_TYPE_ATA_TASKFILE requests
...
broke flush requests.
Allocating IDE command structure on the stack for flush requests is not
a very brilliant idea:
- idedisk_prepare_flush() only prepares the request and it doesn't wait
for it to be completed
- there are can be multiple flush requests queued in the queue
Fix the problem (per hints from James Bottomley) by:
- dynamically allocating ide_task_t instance using kmalloc(..., GFP_ATOMIC)
- adding new taskfile flag (IDE_TFLAG_DYN)
- calling kfree() in ide_end_drive_command() if IDE_TFLAG_DYN is set
(while at it rename 'args' to 'task' and fix whitespace damage)
[ This will be fixed properly before 2.6.25 but this bug is rather
critical and the proper solution requires some more work + testing. ]
Thanks to Sebastian Siewior and Christoph Hellwig for reporting the
problem and testing patches (extra thanks to Sebastian for bisecting
it to the guilty commmit).
Tested-by: Sebastian Siewior <ide-bug@ml.breakpoint.cc>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
Cc: Tejun Heo <htejun@gmail.com>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Introduce new option CONFIG_BLK_DEV_IDEDMA_SFF for non-PCI SFF-8038i compatible
bus mastering IDE controllers (which there are a few known), thus fixing a hack
made for Palmchip BK3710 controller...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Anton Salnikov <asalnikov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
On Saturday 09 February 2008, Adrian Bunk wrote:
> Commit 9e016a7192 causes the following
> compile error:
>
> <-- snip -->
>
> ...
> CC drivers/ide/arm/bast-ide.o
> /home/bunk/linux/kernel-2.6/git/linux-2.6/drivers/ide/arm/bast-ide.c: In function 'bastide_register':
> /home/bunk/linux/kernel-2.6/git/linux-2.6/drivers/ide/arm/bast-ide.c:31: error: 'hwif' redeclared as different kind of symbol
> /home/bunk/linux/kernel-2.6/git/linux-2.6/drivers/ide/arm/bast-ide.c:29: error: previous definition of 'hwif' was here
> make[4]: *** [drivers/ide/arm/bast-ide.o] Error 1
>
> <-- snip -->
Remove 'ide_hwif_t **hwif' argument from bastide_register()
(together with write-only ifs[]).
Cc: Adrian Bunk <bunk@kernel.org>
Cc: Russell King <rmk@arm.linux.org.uk>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
rq->cmd[0] is never set to REQ_IDETAPE_READ_BUFFER so remove
REQ_IDETAPE_READ_BUFFER handling from idetape_create_write_cmd()
and the define itself.
Then remove no longer used idetape_create_read_buffer_cmd()
and IDETAPE_RETRIEVE_FAULTY_BLOCK define.
There should be no functional changes caused by this patch.
Cc: Borislav Petkov <petkovbb@gmail.com>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
On Thursday 03 January 2008, Robert Hancock wrote:
[...]
> How about getting rid of this stupid thing in drivers/ide/ide.c:
>
> #define REVISION "Revision: 7.00alpha2"
>
> which is used in:
>
> printk(KERN_INFO "Uniform Multi-Platform E-IDE driver " REVISION "\n");
>
> It's been 7.00alpha2 for god knows how long, so clearly this version
> number is not useful..
Cc: Robert Hancock <hancockr@shaw.ca>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Alan has noticed that distros always enabled burst mode
(+ datasheet confirms that it is the right thing to do).
Thus fix pdc202xx_old host driver to do it unconditionally
and remove no longer needed CONFIG_PDC202XX_BURST option.
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Probe port _after_ it is fully initialized.
Cc: Anton Salnikov <asalnikov@ru.mvista.com>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Don't set 'restore' flag for ide_unregister() when initializing new
interface.
[ identical change as done to bast-ide/ide-cs/delkin_cb host drivers
by commit 909f4369bc ]
Cc: Anton Salnikov <asalnikov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Convert palm_bk3710 host driver to use ide_device_add() instead of
ide_register_hw() (while at it drop doing "ide_unregister()" loop which
tries to unregister _all_ IDE interfaces if useable ide_hwifs[] slot
cannot be find).
[ identical change as done to bast-ide/ide-cs/delkin_cb host drivers
by commit 9e016a7192 ]
* Rename 'ide_ctlr_info' to 'hw' and 'index' to 'i' while at it.
Cc: Anton Salnikov <asalnikov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Replace the check for hwgroup->handler and printk(KERN_CRIT, ...) at the start
of __ide_set_handler() with mere BUG_ON() while removing such from the caller,
ide_execute_command(). Fix up the code formatting, while at it...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Remove stale comment from the cs5520 IDE driver.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
I have reviewed all blk-end-request patches again to confirm whether
there are any similar problems with the last week's ide-cd panic:
http://lkml.org/lkml/2008/1/29/140
And I found a possible similar bug in ide-io change:
ide_end_drive_cmd() could be called for blk_pc_request() which could
have bios. To complete such requests correctly, we need to pass
the actual size of the request.
Otherwise, __blk_end_request() returns 1 because the request still has
bios, and the system will BUG() unnecessarily.
The following patch fixes the bug and should be applied on top of
Linus' git.
Signed-off-by: Kiyoshi Ueda <k-ueda@ct.jp.nec.com>
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Cc: Borislav Petkov <petkovbb@googlemail.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
We want to allow different implementations of pci_raw_ops for standard
and extended config space on x86. Rather than clutter generic code with
knowledge of this, we make pci_raw_ops private to x86 and use it to
implement the new raw interface -- raw_pci_read() and raw_pci_write().
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
gcc-3.4.4 on powerpc:
drivers/net/starfire.c:219: error: version causes a section type conflict
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
From: Andrew Morton <akpm@linux-foundation.org>
gcc-3.4.4 on powerpc:
drivers/net/via-velocity.c:443: error: chip_info_table causes a section type conflict
on this one I had to remove the __devinitdata too. Don't know why.
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
gcc-3.4.4 on powerpc:
drivers/net/natsemi.c:245: error: natsemi_pci_info causes a section type conflict
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
gcc-3.4.4 on powerpc:
drivers/net/typhoon.c:137: error: version causes a section type conflict
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix following warnings:
WARNING: drivers/isdn/hisax/built-in.o(.text+0x19723): Section mismatch in reference from the function ISACVersion() to the variable .devinit.data:ISACVer
WARNING: drivers/isdn/hisax/built-in.o(.text+0x2005b): Section mismatch in reference from the function setup_avm_a1_pcmcia() to the function .devinit.text:setup_isac()
ISACVer were only used from function annotated __devinit
so add same annotation to ISACVer.
One af the fererencing functions missed __devinit so add it
and kill an additional warning.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Acked-by: Karsten Keil <kkeil@suse.de>
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the following warnings:
WARNING: drivers/isdn/hisax/built-in.o(.text+0x722): Section mismatch in reference from the function hisax_cs_setup_card() to the function .devinit.text:setup_teles3()
WARNING: drivers/isdn/hisax/built-in.o(.text+0x72c): Section mismatch in reference from the function hisax_cs_setup_card() to the function .devinit.text:setup_s0box()
WARNING: drivers/isdn/hisax/built-in.o(.text+0x736): Section mismatch in reference from the function hisax_cs_setup_card() to the function .devinit.text:setup_telespci()
WARNING: drivers/isdn/hisax/built-in.o(.text+0x747): Section mismatch in reference from the function hisax_cs_setup_card() to the function .devinit.text:setup_avm_pcipnp()
WARNING: drivers/isdn/hisax/built-in.o(.text+0x74e): Section mismatch in reference from the function hisax_cs_setup_card() to the function .devinit.text:setup_elsa()
WARNING: drivers/isdn/hisax/built-in.o(.text+0x755): Section mismatch in reference from the function hisax_cs_setup_card() to the function .devinit.text:setup_diva()
WARNING: drivers/isdn/hisax/built-in.o(.text+0x75c): Section mismatch in reference from the function hisax_cs_setup_card() to the function .devinit.text:setup_sedlbauer()
WARNING: drivers/isdn/hisax/built-in.o(.text+0x763): Section mismatch in reference from the function hisax_cs_setup_card() to the function .devinit.text:setup_netjet_s()
WARNING: drivers/isdn/hisax/built-in.o(.text+0x76a): Section mismatch in reference from the function hisax_cs_setup_card() to the function .devinit.text:setup_hfcpci()
WARNING: drivers/isdn/hisax/built-in.o(.text+0x771): Section mismatch in reference from the function hisax_cs_setup_card() to the function .devinit.text:setup_hfcsx()
WARNING: drivers/isdn/hisax/built-in.o(.text+0x778): Section mismatch in reference from the function hisax_cs_setup_card() to the function .devinit.text:setup_niccy()
WARNING: drivers/isdn/hisax/built-in.o(.text+0x77f): Section mismatch in reference from the function hisax_cs_setup_card() to the function .devinit.text:setup_bkm_a4t()
WARNING: drivers/isdn/hisax/built-in.o(.text+0x786): Section mismatch in reference from the function hisax_cs_setup_card() to the function .devinit.text:setup_sct_quadro()
WARNING: drivers/isdn/hisax/built-in.o(.text+0x78d): Section mismatch in reference from the function hisax_cs_setup_card() to the function .devinit.text:setup_gazel()
WARNING: drivers/isdn/hisax/built-in.o(.text+0x794): Section mismatch in reference from the function hisax_cs_setup_card() to the function .devinit.text:setup_w6692()
WARNING: drivers/isdn/hisax/built-in.o(.text+0x79b): Section mismatch in reference from the function hisax_cs_setup_card() to the function .devinit.text:setup_netjet_u()
WARNING: drivers/isdn/hisax/built-in.o(.text+0x7a2): Section mismatch in reference from the function hisax_cs_setup_card() to the function .devinit.text:setup_enternow_pci()
checkcard() are the only user of hisax_cs_setup_card().
And checkcard is only used during init or when hot plugging
ISDN devices. So annotate hisax_cs_setup_card() with __devinit.
checkcard() is used by exported functions so it cannot be
annotated __devinit. Annotate it with __ref so modpost
ignore references to _devinit section.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Acked-by: Karsten Keil <kkeil@suse.de>
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the following warnings:
WARNING: drivers/isdn/hisax/built-in.o(.text+0x1b276): Section mismatch in reference from the function inithscxisac() to the function .devinit.text:clear_pending_isac_ints()
WARNING: drivers/isdn/hisax/built-in.o(.text+0x1b286): Section mismatch in reference from the function inithscxisac() to the function .devinit.text:initisac()
WARNING: drivers/isdn/hisax/built-in.o(.text+0x1fec7): Section mismatch in reference from the function AVM_card_msg() to the function .devinit.text:clear_pending_isac_ints()
WARNING: drivers/isdn/hisax/built-in.o(.text+0x21669): Section mismatch in reference from the function AVM_card_msg() to the function .devinit.text:clear_pending_isac_ints()
WARNING: drivers/isdn/hisax/built-in.o(.text+0x21671): Section mismatch in reference from the function AVM_card_msg() to the function .devinit.text:initisac()
WARNING: drivers/isdn/hisax/built-in.o(.text+0x2991e): Section mismatch in reference from the function Sedl_card_msg() to the function .devinit.text:clear_pending_isac_ints()
WARNING: drivers/isdn/hisax/built-in.o(.text+0x29936): Section mismatch in reference from the function Sedl_card_msg() to the function .devinit.text:initisac()
WARNING: drivers/isdn/hisax/built-in.o(.text+0x2993e): Section mismatch in reference from the function Sedl_card_msg() to the function .devinit.text:initisar()
WARNING: drivers/isdn/hisax/built-in.o(.text+0x2e026): Section mismatch in reference from the function NETjet_S_card_msg() to the function .devinit.text:clear_pending_isac_ints()
WARNING: drivers/isdn/hisax/built-in.o(.text+0x2e02e): Section mismatch in reference from the function NETjet_S_card_msg() to the function .devinit.text:initisac()
WARNING: drivers/isdn/hisax/built-in.o(.text+0x37813): Section mismatch in reference from the function BKM_card_msg() to the function .devinit.text:clear_pending_isac_ints()
WARNING: drivers/isdn/hisax/built-in.o(.text+0x37823): Section mismatch in reference from the function BKM_card_msg() to the function .devinit.text:initisac()
initisar(), initisac() and clear_pending_isac_ints()
were all used via a cardmsg fnction - which may be called
ouside __devinit context.
So remove the bogus __devinit annotation of the
above three functions to fix the warnings.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Acked-by: Karsten Keil <kkeil@suse.de>
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the following warning:
WARNING: drivers/isdn/hisax/built-in.o(.text+0x35818): Section mismatch in reference from the function hfcsx_card_msg() to the function .devinit.text:inithfcsx()
hfcsx_card_msg() may be called outside __devinit context.
Following the program logic is looks like the CARD_INIT branch
will only be taken under __devinit context but to be consistent
remove the __devinit annotation of inithfcsx() so we
do not mix non-__devinit and __devinit code.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Acked-by: Karsten Keil <kkeil@suse.de>
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/net/pppol2tp.c: In function `pppol2tp_seq_tunnel_show':
drivers/net/pppol2tp.c:2295: warning: long long unsigned int format, __u64 arg (arg 4)
drivers/net/pppol2tp.c:2295: warning: long long unsigned int format, __u64 arg (arg 5)
drivers/net/pppol2tp.c:2295: warning: long long unsigned int format, __u64 arg (arg 6)
drivers/net/pppol2tp.c:2295: warning: long long unsigned int format, __u64 arg (arg 7)
drivers/net/pppol2tp.c:2295: warning: long long unsigned int format, __u64 arg (arg 8)
drivers/net/pppol2tp.c:2295: warning: long long unsigned int format, __u64 arg (arg 9)
drivers/net/pppol2tp.c: In function `pppol2tp_seq_session_show':
drivers/net/pppol2tp.c:2328: warning: long long unsigned int format, __u64 arg (arg 5)
drivers/net/pppol2tp.c:2328: warning: long long unsigned int format, __u64 arg (arg 6)
drivers/net/pppol2tp.c:2328: warning: long long unsigned int format, __u64 arg (arg 7)
drivers/net/pppol2tp.c:2328: warning: long long unsigned int format, __u64 arg (arg 8)
drivers/net/pppol2tp.c:2328: warning: long long unsigned int format, __u64 arg (arg 9)
drivers/net/pppol2tp.c:2328: warning: long long unsigned int format, __u64 arg (arg 10)
Not all platforms implement u64 with unsigned long long. eg: powerpc.
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
gcc-3.4.4 on powerpc:
drivers/net/bnx2.c:67: error: version causes a section type conflict
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
From: Andrew Morton <akpm@linux-foundation.org>
gcc-3.4.4 on powerpc:
drivers/net/bnx2x.c:73: error: version causes a section type conflict
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stefano Brivio
Mohamed Abbas
Gregory Greenman
Reinette Chatre
Jussi Kivilinna
Bruno Randolf
John W. Linville
David Graham
Auke Kok
Al Viro
Jarek Poplawski
Chuck Ebbert
Linus Torvalds
Patrick McHardy
Keiichi KII
Jan Blunck
Tony Breeds
Sean Hefty
Jack Morgenstein
Eli Cohen
Adrian Bunk
Geoff Levand
Takashi Yamamoto
Len Brown
Roel Kluin
Rafael J. Wysocki
Paul Mundt
Adrian McMenamin
Magnus Damm
Venkatesh Pallipadi
David Brownell
Harvey Harrison
Tobias Mueller
Marcin Slusarz
Steve Wise
Sergio Luis
Boaz Harrosh
Robert Reif
David Newall
David S. Miller
Roland Dreier
James Bottomley
James Smart
Olof Johansson
Julia Lawall
Alex Bounine
Byron Bradley
Alan Cox
Yinghai Lu
Tejun Heo
Salyzyn, Mark
Prakash, Sathya
Thomas Horsten
FUJITA Tomonori
Sergio Luis
Peter Tiedemann
Ursula Braun
Cornelia Huck
Ayaz Abdulla
Jeff Garzik
Ben Dooks
Krishna Kumar
Benjamin Herrenschmidt
Masakazu Mokuno
Adrian McMenamin
Don Fry
Jiri Kosina
Jeremy Roberson
Bartlomiej Zolnierkiewicz
Sergei Shtylyov
Borislav Petkov
Kiyoshi Ueda
Matthew Wilcox
Andrew Morton
Sam Ravnborg
S.Çağlar Onur