Implement the suspend/resume procedure for the Broadcom AC131 and BCM5241 type
of PHYs (10/100 only) by entering the standard power down followed by the
proprietary standby mode in the auxiliary mode 4 shadow register. On resume,
the PHY software reset is enough to make it come out of standby mode so we can
utilize brcm_fet_config_init() as the resume hook.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for BCM53128 internal PHYs. These support interrupts as well as
statistics. Therefore, enable the Broadcom PHY driver for them.
Tested on BCM53128 switch using the mainline b53 DSA driver.
Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
7712 is a 16nm process SoC with a 10/100 integrated Ethernet PHY,
utilize the recently defined 16nm EPHY macro to configure that PHY.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
An extraneous number was added during the inclusion of that change,
correct that such that we use a single bit as is expected by the PHY
driver.
Reported-by: Justin Chen <justinpopo6@gmail.com>
Fixes: d6da08ed14 ("net: phy: broadcom: Add IDDQ-SR mode")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for putting the PHY into IDDQ Soft Recovery mode by setting
the TOP_MISC register bits accordingly. This requires us to implement a
custom bcm54xx_suspend() routine which diverges from genphy_suspend() in
order to configure the PHY to enter IDDQ with software recovery as well
as avoid doing a read/modify/write on the BMCR register.
Doing a read/modify/write on the BMCR register means that the
auto-negotation bit may remain which interferes with the ability to put
the PHY into IDDQ-SR mode. We do software reset upon suspend in order to
put the PHY back into its state prior to suspend as recommended by the
datasheet.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
72165 is a 16nm process SoC with a 10/100 integrated Ethernet PHY,
create a new macro and set of functions for this different process type.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20210917181551.2836036-1-f.fainelli@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Enable the DAC early wake when then link operates at 10BaseT allows
power savings in the hundreds of milli Watts by shutting down the
transmitter. A number of errata have been issued for various Gigabit
PHYs and the recommendation is to enable both the early and forced DAC
wake to be on the safe side. This needs to be done dynamically based
upon the link state, which is why a link_change_notify callback is
utilized.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20210916212742.1653088-1-f.fainelli@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The tg3 driver tried to communicate towards the PHY driver whether it
wanted RGMII in-band signaling enabled or disabled however there is
nothing that looks at those flags in drivers/net/phy/broadcom.c so this
does do not anything.
Suggested-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
BCM54210E/BCM50212E has been verified to work correctly with the
auto-power down configuration done by bcm54xx_adjust_rxrefclk(), add it
to the list of PHYs working.
While we are at it, provide an appropriate name for the bit we are
changing which disables the RXC and TXC during auto-power down when
there is no energy on the cable.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We have a number of unused flags defined today and since we are scarce
on space and may need to introduce new flags in the future remove and
shift every existing flag down into a contiguous assignment.
PHY_BCM_FLAGS_MODE_1000BX was only used internally for the BCM54616S
PHY, so we allocate a driver private structure instead to store that
flag instead of canibalizing one from phydev->dev_flags for that
purpose.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
BCM72116 features a 28nm integrated EPHY, add an entry to match this PHY
OUI.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20210106170944.1253046-1-f.fainelli@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
BCM72113 features a 28nm integrated EPHY, add an entry to the driver for
it.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The BCM54811 PHY shares many similarities with the already supported BCM54810
PHY but additionally requires some semi-unique configuration.
Signed-off-by: Kevin Lo <kevlo@kevlo.org>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Most modern broadcom PHYs support ECD (enhanced cable diagnostics). Add
support for it in the bcm-phy-lib so they can easily be used in the PHY
driver.
There are two access methods for ECD: legacy by expansion registers and
via the new RDB registers which are exclusive. Provide functions in two
variants where the PHY driver can choose from. To keep things simple for
now, we just switch the register access to expansion registers in the
RDB variant for now. On the flipside, we have to keep a bus lock to
prevent any other non-legacy access on the PHY.
The results of the intra-pair tests are inconclusive (at least for the
BCM54140). Most of the times half the length is reported but sometimes
the length is correct.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This PHY has two PHY IDs depending on its mode. Adjust the mask so that
it includes both IDs.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Broadcom BCM54140 is a Quad SGMII/QSGMII Copper/Fiber Gigabit
Ethernet transceiver.
This also adds support for tunables to set and get downshift and
energy detect auto power-down.
The PHY has four ports and each port has its own PHY address.
There are per-port registers as well as global registers.
Unfortunately, the global registers can only be accessed by reading
and writing from/to the PHY address of the first port. Further,
there is no way to find out what port you actually are by just
reading the per-port registers. We therefore, have to scan the
bus on the PHY probe to determine the port and thus what address
we need to access the global registers.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
RDB (Register Data Base) registers are used on newer Broadcom PHYs. Add
helper to read, write and modify these registers.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
BCM53125 has internal Gigabit PHYs which support interrupts as well as
statistics, make it possible to configure both of those features with a
PHY driver entry.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The BCM7XX PHY family requires special configuration to pass jumbo
frames. Do that during initial PHY setup.
Signed-off-by: Murali Krishna Policharla <murali.policharla@broadcom.com>
Reviewed-by: Scott Branden <scott.branden@broadcom.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The BCM54616S PHY cannot work properly in RGMII->1000Base-X mode, mainly
because genphy functions are designed for copper links, and 1000Base-X
(clause 37) auto negotiation needs to be handled differently.
This patch enables 1000Base-X support for BCM54616S by customizing 3
driver callbacks, and it's verified to be working on Facebook CMM BMC
platform (RGMII->1000Base-KX):
- probe: probe callback detects PHY's operation mode based on
INTERF_SEL[1:0] pins and 1000X/100FX selection bit in SerDES 100-FX
Control register.
- config_aneg: calls genphy_c37_config_aneg when the PHY is running in
1000Base-X mode; otherwise, genphy_config_aneg will be called.
- read_status: calls genphy_c37_read_status when the PHY is running in
1000Base-X mode; otherwise, genphy_read_status will be called.
Note: BCM54616S PHY can also be configured in RGMII->100Base-FX mode, and
100Base-FX support is not available as of now.
Signed-off-by: Tao Ren <taoren@fb.com>
Acked-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previously the green and amber LEDs on this quad PHY were solid, to
indicate an encoding of the link speed (10/100/1000).
This keeps the LEDs always on just as before, but now they flash on
Rx/Tx activity.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for BCM7255 EPHY.
Signed-off-by: Justin Chen <justinpopo6@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for the Broadcom Omega SoC internal Combo Ethernet
GPHY to the bcm7xxx phy driver.
Signed-off-by: Arun Parameswaran <arun.parameswaran@broadcom.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
BCM54612E have 4 multi-functional LED pins that can be configured
through register setting; the LED4 pin can be configured to a 125MHz
reference clock output by setting the spare register. Since the dedicated
CLK125 reference clock pin is not brought out on the 48-Pin MLP, the LED4
pin is the only pin to provide such function in this package, and therefore
it is beneficial to just enable the reference clock by default.
Signed-off-by: Kun Yi <kunyi@google.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It adds support for BCM89610 (Single-Port 10/100/1000BASE-T)
transceiver which is used in P3310 Tegra186 platform.
Signed-off-by: Bhadram Varka <vbhadram@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add an entry for the builtin PHYs present in the Broadcom BCM5395 switch. This
allows us to retrieve the PHY statistics among other things.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Chris Healy <cphealy@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Files removed in 'net-next' had their license header updated
in 'net'. We take the remove from 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some of Broadcom's PHYs run by default in slave mode with Automatic
Slave/Master configuration disabled. It stops them from working properly
with some devices.
So far it has been verified for BCM54210E and BCM50212E which don't
work well with Intel's I217-LM and I218-LM:
http://ark.intel.com/products/60019/Intel-Ethernet-Connection-I217-LMhttp://ark.intel.com/products/71307/Intel-Ethernet-Connection-I218-LM
I was told there is massive ping loss.
This commit adds support for a new flag which can be set by an ethernet
driver to fixup PHY setup.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit adds support for the internal fast ethernet 10/100 PHY
found in the BCM7260, BCM7268, and BCM7271 devices.
Signed-off-by: Doug Berger <opendmb@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the BCM74371 PHY ID to the list of supported chips. This is a 28nm
technology Gigabit PHY SoC.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's Broadcom PHY simply described as single-port
RGMII 10/100/1000BASE-T PHY. It requires disabling delay skew and GTXCLK
bits.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
1) Use 0x%02x format for register number. This follows some other
defines and makes it easier to distinct register from values.
2) Put register define above values and sort the values. It makes
reading header code easier.
3) Use 0x%04x format for all values. It's about consistency with other
values (and most of the header) not a personal preference.
4) Separate define for reading shift value with an extre empty line.
It's user for all AUXCTL registers in a bcm54xx_auxctl_read.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We had two defines for the same bit (both were used with the
MII_BCM54XX_AUXCTL_SHDWSEL_MISC register).
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Starting with commit 5b4e290051 ("net: phy: broadcom: add
bcm54xx_auxctl_read") we have a reading helper so use it and avoid code
duplication.
It also means we don't need MII_BCM54XX_AUXCTL_SHDWSEL_MISC define as
it's the same as MII_BCM54XX_AUXCTL_SHDWSEL_MISC just for reading needs
(same value shifted by 12 bits).
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for the BCM7278 28nm process Gigabit Ethernet PHY.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Broadcom PHYs expose a number of PHY error counters: receive errors,
false carrier sense, SerDes BER count, local and remote receive errors.
Add support code to allow retrieving these error counters. Since the
Broadcom PHY library code is used by several drivers, make it possible
for them to specify the storage for the software copy of the statistics.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Broadcom's Wirespeed feature allows us to configure how auto-negotiation
should behave with fewer working pairs of wires on a cable. Add support
code for retrieving and setting such downshift counters using the
recently added ethtool downshift tunables.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The BCM54810 PHY requires some semi-unique configuration, which results
in some additional configuration in addition to the standard config.
Also, some users of the BCM54810 require the PHY lanes to be swapped.
Since there is no way to detect this, add a device tree query to see if
it is applicable.
Inspired-by: Vikas Soni <vsoni@broadcom.com>
Signed-off-by: Jon Mason <jon.mason@broadcom.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a helper function to read the AUXCTL register for the BCM54xx. This
mirrors the bcm54xx_auxctl_write function already present in the code.
Signed-off-by: Jon Mason <jon.mason@broadcom.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This PHY has internal delays enabled after reset. This clears the
internal delay enables unless the interface specifically requests them.
Signed-off-by: Xo Wang <xow@google.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the RXD-to-RXC skew (delay) time bit in the Miscellaneous Control
shadow register and a mask for the shadow selector field.
Remove a re-definition of MII_BCM54XX_AUXCTL_SHDWSEL_AUXCTL.
Signed-off-by: Xo Wang <xow@google.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add PHY entries for the Broadcom BCM7346 and BCM7362 chips, these are
40nm generation Ethernet PHY.
Fixes: 815717d147 ("net: phy: bcm7xxx: Remove wildcard entries")
Signed-off-by: Jaedon Shin <jaedon.shin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a PHY entry for the Broadcom BCM7435 chips, this is a 40nm
generation Ethernet PHY which is analogous to its 7425 and 7429 counter
parts.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for the Broadcom Cygnus SoCs internal PHY's.
The PHYs are 1000M/100M/10M capable with support for 'EEE'
and 'APD' (Auto Power Down).
This driver supports the following Broadcom Cygnus SoCs:
- BCM583XX (BCM58300, BCM58302, BCM58303, BCM58305)
- BCM113XX (BCM11300, BCM11320, BCM11350, BCM11360)
The PHY's on these SoC's require some workarounds for
stable operation, both during configuration time and
during suspend/resume. This driver handles the
application of the workarounds.
Signed-off-by: Arun Parameswaran <arunp@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the Broadcom phy library to consolidate common
interfaces shared by Broadcom phy's.
Moved the common interfaces to the 'bcm-phy-lib.c' and updated
the Broadcom PHY drivers to use the new APIs.
Signed-off-by: Arun Parameswaran <arunp@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Define the pseudo-PHY address (30) which is used by all Broadcom
Ethernet switches in a shared header file.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We utilize inline functions from the PHY library, make sure that we do
include phy.h in brcmphy.h in order for the code including brcmphy.h not
to have to resolve this inclusion dependency.
Fixes: 705314797b ("net: phy: broadcom: move shadow 0x1C register accessors to brcmphy.h")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While adding support for 7425 PHY in the 7xxx PHY driver, the ID that
was used was actually coming from an external PHY: a BCM5461x. Fix this
by using the proper ID for the internal 7425 PHY and set the
PHY_IS_INTERNAL flag, otherwise consumers of this PHY driver would not
be able to properly identify it as such.
Fixes: d068b02cfd ("net: phy: add BCM7425 and BCM7429 PHYs")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Petri Gynther <pgynther@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Fainelli
Kurt Kanzenbach
Robert Hancock
Kevin Lo
Michael Walle
Murali Krishna Policharla
Tao Ren
Vladimir Oltean
Justin Chen
Arun Parameswaran
Kun Yi
Bhadram Varka
David S. Miller
Greg Kroah-Hartman
Rafał Miłecki
Doug Berger
Jon Mason
Xo Wang
Jaedon Shin
Arun Parameswaran