After commit d12544fb2a ("PM: runtime: Remove link state checks in
rpm_get/put_supplier()") nothing prevents the consumer device's
runtime PM from acquiring additional references to the supplier
device after pm_runtime_clean_up_links() has run (or even while it
is running), so calling this function from __device_release_driver()
may be pointless (or even harmful).
Moreover, it ignores stateless device links, so the runtime PM
handling of managed and stateless device links is inconsistent
because of it, so better get rid of it entirely.
Fixes: d12544fb2a ("PM: runtime: Remove link state checks in rpm_get/put_supplier()")
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Cc: 5.1+ <stable@vger.kernel.org> # 5.1+
Tested-by: Xiang Chen <chenxiang66@hisilicon.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
While removing a device link, drop the supplier device's runtime PM
usage counter as many times as needed to drop all of the runtime PM
references to it from the consumer in addition to dropping the
consumer's link count.
Fixes: baa8809f60 ("PM / runtime: Optimize the use of device links")
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Cc: 5.1+ <stable@vger.kernel.org> # 5.1+
Tested-by: Xiang Chen <chenxiang66@hisilicon.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
To support runtime PM for hisi SAS driver (the driver is in directory
drivers/scsi/hisi_sas), we add device link between scsi_device->sdev_gendev
(consumer device) and hisi_hba->dev(supplier device) with flags
DL_FLAG_PM_RUNTIME | DL_FLAG_RPM_ACTIVE.
After runtime suspended consumers and supplier, unload the dirver which
causes a hung.
We found that it called function device_release_driver_internal() to
release the supplier device (hisi_hba->dev), as the device link was
busy, it set the device link state to DL_STATE_SUPPLIER_UNBIND, and
then it called device_release_driver_internal() to release the consumer
device (scsi_device->sdev_gendev).
Then it would try to call pm_runtime_get_sync() to resume the consumer
device, but because consumer-supplier relation existed, it would try
to resume the supplier first, but as the link state was already
DL_STATE_SUPPLIER_UNBIND, so it skipped resuming the supplier and only
resumed the consumer which hanged (it sends IOs to resume scsi_device
while the SAS controller is suspended).
Simple flow is as follows:
device_release_driver_internal -> (supplier device)
if device_links_busy ->
device_links_unbind_consumers ->
...
WRITE_ONCE(link->status, DL_STATE_SUPPLIER_UNBIND)
device_release_driver_internal (consumer device)
pm_runtime_get_sync -> (consumer device)
...
__rpm_callback ->
rpm_get_suppliers ->
if link->state == DL_STATE_SUPPLIER_UNBIND -> skip the action of resuming the supplier
...
pm_runtime_clean_up_links
...
Correct suspend/resume ordering between a supplier device and its consumer
devices (resume the supplier device before resuming consumer devices, and
suspend consumer devices before suspending the supplier device) should be
guaranteed by runtime PM, but the state checks in rpm_get_supplier() and
rpm_put_supplier() break this rule, so remove them.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
[ rjw: Subject and changelog edits ]
Cc: All applicable <stable@vger.kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The kerneldoc comment of pm_runtime_get_if_active() doesn't list the
second argument of the function properly, so fix that and while at it
clarify that comment somewhat and add some markup to it.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Sakari Ailus <sakari.ailus@linux.intel.com>
rpm_suspend() simple bails out when conditions are wrong. But this is not
immediately obvious from the code. Make it clear what we do when conditions
are wrong in rpm_suspend().
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
pm_runtime_get_if_in_use() bumps up the PM-runtime usage count if it
is not equal to zero and the device's PM-runtime status is 'active'.
This works for drivers that do not use autoidle, but for those that
do, the function returns zero even when the device is active.
In order to maintain sane device state while the device is powered on
in the hope that it'll be needed, pm_runtime_get_if_active(dev, true)
returns a positive value if the device's PM-runtime status is 'active'
when it is called, in which case it also increments the device's usage
count.
If the second argument of pm_runtime_get_if_active() is 'false', the
function behaves just like pm_runtime_get_if_in_use(), so redefine
the latter as a wrapper around the former.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
[ rjw: Changelog ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Add tracepoints to remaining places where device's power.usage_count
is changed.
This helps debugging where and why autosuspend is prevented.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Here is the big driver core update for 5.4-rc1.
There was a bit of a churn in here, with a number of core and OF
platform patches being added to the tree, and then after much discussion
and review and a day-long in-person meeting, they were decided to be
reverted and a new set of patches is currently being reviewed on the
mailing list.
Other than that churn, there are two "persistent" branches in here that
other trees will be pulling in as well during the merge window. One
branch to add support for drivers to have the driver core automatically
add sysfs attribute files when a driver is bound to a device so that the
driver doesn't have to manually do it (and then clean it up, as it
always gets it wrong).
There's another branch in here for generic lookup helpers for the driver
core that lots of busses are starting to use. That's the majority of
the non-driver-core changes in this patch series.
There's also some on-going debugfs file creation cleanup that has been
slowly happening over the past few releases, with the goal to hopefully
get that done sometime next year.
All of these have been in linux-next for a while now with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXYIVHA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymEVwCfRPxQHQplI6ZR6h0jPscLSaZnaFIAn1a+rjO2
EFuuXJ5Ip72F5Ch9AW3G
=r8lH
-----END PGP SIGNATURE-----
Merge tag 'driver-core-5.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg Kroah-Hartman:
"Here is the big driver core update for 5.4-rc1.
There was a bit of a churn in here, with a number of core and OF
platform patches being added to the tree, and then after much
discussion and review and a day-long in-person meeting, they were
decided to be reverted and a new set of patches is currently being
reviewed on the mailing list.
Other than that churn, there are two "persistent" branches in here
that other trees will be pulling in as well during the merge window.
One branch to add support for drivers to have the driver core
automatically add sysfs attribute files when a driver is bound to a
device so that the driver doesn't have to manually do it (and then
clean it up, as it always gets it wrong).
There's another branch in here for generic lookup helpers for the
driver core that lots of busses are starting to use. That's the
majority of the non-driver-core changes in this patch series.
There's also some on-going debugfs file creation cleanup that has been
slowly happening over the past few releases, with the goal to
hopefully get that done sometime next year.
All of these have been in linux-next for a while now with no reported
issues"
[ Note that the above-mentioned generic lookup helpers branch was
already brought in by the LED merge (commit 4feaab05dc) that had
shared it.
Also note that that common branch introduced an i2c bug due to a bad
conversion, which got fixed here. - Linus ]
* tag 'driver-core-5.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (49 commits)
coccinelle: platform_get_irq: Fix parse error
driver-core: add include guard to linux/container.h
sysfs: add BIN_ATTR_WO() macro
driver core: platform: Export platform_get_irq_optional()
hwmon: pwm-fan: Use platform_get_irq_optional()
driver core: platform: Introduce platform_get_irq_optional()
Revert "driver core: Add support for linking devices during device addition"
Revert "driver core: Add edit_links() callback for drivers"
Revert "of/platform: Add functional dependency link from DT bindings"
Revert "driver core: Add sync_state driver/bus callback"
Revert "of/platform: Pause/resume sync state during init and of_platform_populate()"
Revert "of/platform: Create device links for all child-supplier depencencies"
Revert "of/platform: Don't create device links for default busses"
Revert "of/platform: Fix fn definitons for of_link_is_valid() and of_link_property()"
Revert "of/platform: Fix device_links_supplier_sync_state_resume() warning"
Revert "of/platform: Disable generic device linking code for PowerPC"
devcoredump: fix typo in comment
devcoredump: use memory_read_from_buffer
of/platform: Disable generic device linking code for PowerPC
device.h: Fix warnings for mismatched parameter names in comments
...
This commit applies the consolidated hlist_for_each_entry_rcu() support
for lockdep conditions.
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Joel Fernandes (Google) <joel@joelfernandes.org>
Signed-off-by: Paul E. McKenney <paulmck@linux.ibm.com>
If device_link_add() is called for a consumer/supplier pair with an
existing device link between them and the existing link's type is
not in agreement with the flags passed to that function by its
caller, NULL will be returned. That is seriously inconvenient,
because it forces the callers of device_link_add() to worry about
what others may or may not do even if that is not relevant to them
for any other reasons.
It turns out, however, that this limitation can be made go away
relatively easily.
The underlying observation is that if DL_FLAG_STATELESS has been
passed to device_link_add() in flags for the given consumer/supplier
pair at least once, calling either device_link_del() or
device_link_remove() to release the link returned by it should work,
but there are no other requirements associated with that flag. In
turn, if at least one of the callers of device_link_add() for the
given consumer/supplier pair has not passed DL_FLAG_STATELESS to it
in flags, the driver core should track the status of the link and act
on it as appropriate (ie. the link should be treated as "managed").
This means that DL_FLAG_STATELESS needs to be set for managed device
links and it should be valid to call device_link_del() or
device_link_remove() to drop references to them in certain
sutiations.
To allow that to happen, introduce a new (internal) device link flag
called DL_FLAG_MANAGED and make device_link_add() set it automatically
whenever DL_FLAG_STATELESS is not passed to it. Also make it take
additional references to existing device links that were previously
stateless (that is, with DL_FLAG_STATELESS set and DL_FLAG_MANAGED
unset) and will need to be managed going forward and initialize
their status (which has been DL_STATE_NONE so far).
Accordingly, when a managed device link is dropped automatically
by the driver core, make it clear DL_FLAG_MANAGED, reset the link's
status back to DL_STATE_NONE and drop the reference to it associated
with DL_FLAG_MANAGED instead of just deleting it right away (to
allow it to stay around in case it still needs to be released
explicitly by someone).
With that, since setting DL_FLAG_STATELESS doesn't mean that the
device link in question is not managed any more, replace all of the
status-tracking checks against DL_FLAG_STATELESS with analogous
checks against DL_FLAG_MANAGED and update the documentation to
reflect these changes.
While at it, make device_link_add() reject flags that it does not
recognize, including DL_FLAG_MANAGED.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Saravana Kannan <saravanak@google.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Review-by: Saravana Kannan <saravanak@google.com>
Link: https://lore.kernel.org/r/2305283.AStDPdUUnE@kreacher
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dev_pm_qos_read_value() will soon need to support more constraint types
(min/max frequency) and will have another argument to it, i.e. type of
the constraint. While that is fine for the existing users of
dev_pm_qos_read_value(), but not that optimal for the callers of
__dev_pm_qos_read_value() and dev_pm_qos_raw_read_value() as all the
callers of these two routines are only looking for resume latency
constraint.
Lets make these two routines care only about the resume latency
constraint and rename them to __dev_pm_qos_resume_latency() and
dev_pm_qos_raw_resume_latency().
Suggested-by: Rafael J. Wysocki <rjw@rjwysocki.net>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
There were a few files in the driver core power code that did not have
SPDX identifiers on them, so fix that up. At the same time, remove the
"free form" text that specified the license of the file, as that is
impossible for any tool to properly parse.
Cc: "Rafael J. Wysocki" <rafael@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
- Fix registration of new cpuidle governors partially broken during
the 5.0 development cycle by mistake (Rafael Wysocki).
- Avoid integer overflows in the menu cpuidle governor by making
it discard the overflowing data points upfront (Rafael Wysocki).
- Fix minor mistake in the recent update of the iowait boost
computation in the intel_pstate driver (Rafael Wysocki).
- Drop incorrect __init annotation from one function in the pxa2xx
cpufreq driver (Arnd Bergmann).
- Fix the operating performance points (OPP) framework
initialization for devices in multiple power domains if
only one of them is scalable (Rajendra Nayak).
- Fix mistake in dev_pm_opp_set_rate() which causes it to skip
updating the performance state if the new frequency is the same
as the old one (Viresh Kumar).
- Rework the cancellation of wakeup source timers to avoid
potential issues with it and do some cleanups unlocked by
that change (Viresh Kumar, Rafael Wysocki).
- Clean up the code computing the active/suspended time of devices
in the PM-runtime framework after recent changes (Ulf Hansson).
- Make the power management infrastructure code use pr_fmt()
consistently (Joe Perches).
- Clean up the generic power domains (genpd) framework somewhat
(Aisheng Dong).
- Improve kerneldoc comments for two functions in the cpufreq core
(Rafael Wysocki).
- Fix typo in a PM QoS file description comment (Aisheng Dong).
- Update the handling of CPU boost frequencies in the cpupower
utility (Abhishek Goel).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=fHRq
-----END PGP SIGNATURE-----
Merge tag 'pm-5.1-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull more power management updates from Rafael Wysocki:
"These are mostly fixes and cleanups on top of the previously merged
power management material for 5.1-rc1 with one cpupower utility update
that wasn't pushed earlier due to unfortunate timing.
Specifics:
- Fix registration of new cpuidle governors partially broken during
the 5.0 development cycle by mistake (Rafael Wysocki).
- Avoid integer overflows in the menu cpuidle governor by making it
discard the overflowing data points upfront (Rafael Wysocki).
- Fix minor mistake in the recent update of the iowait boost
computation in the intel_pstate driver (Rafael Wysocki).
- Drop incorrect __init annotation from one function in the pxa2xx
cpufreq driver (Arnd Bergmann).
- Fix the operating performance points (OPP) framework initialization
for devices in multiple power domains if only one of them is
scalable (Rajendra Nayak).
- Fix mistake in dev_pm_opp_set_rate() which causes it to skip
updating the performance state if the new frequency is the same as
the old one (Viresh Kumar).
- Rework the cancellation of wakeup source timers to avoid potential
issues with it and do some cleanups unlocked by that change (Viresh
Kumar, Rafael Wysocki).
- Clean up the code computing the active/suspended time of devices in
the PM-runtime framework after recent changes (Ulf Hansson).
- Make the power management infrastructure code use pr_fmt()
consistently (Joe Perches).
- Clean up the generic power domains (genpd) framework somewhat
(Aisheng Dong).
- Improve kerneldoc comments for two functions in the cpufreq core
(Rafael Wysocki).
- Fix typo in a PM QoS file description comment (Aisheng Dong).
- Update the handling of CPU boost frequencies in the cpupower
utility (Abhishek Goel)"
* tag 'pm-5.1-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
cpuidle: governor: Add new governors to cpuidle_governors again
cpufreq: intel_pstate: Fix up iowait_boost computation
PM / OPP: Update performance state when freq == old_freq
PM / wakeup: Drop wakeup_source_drop()
PM / wakeup: Rework wakeup source timer cancellation
PM / domains: Remove one unnecessary blank line
PM / Domains: Return early for all errors in _genpd_power_off()
PM / Domains: Improve warn for multiple states but no governor
OPP: Fix handling of multiple power domains
PM / QoS: Fix typo in file description
cpufreq: pxa2xx: remove incorrect __init annotation
PM-runtime: Call pm_runtime_active|suspended_time() from sysfs
PM-runtime: Consolidate code to get active/suspended time
PM: Add and use pr_fmt()
cpufreq: Improve kerneldoc comments for cpufreq_cpu_get/put()
cpuidle: menu: Avoid overflows when computing variance
tools/power/cpupower: Display boost frequency separately
Avoid the open-coding of the accounted time acquisition in
runtime_active|suspend_time_show() and make them call
pm_runtime_active|suspended_time() instead.
Note that this change also indirectly avoids holding dev->power.lock
around the do_div() computation and the sprintf() call which is an
additional improvement.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
[ rjw: Changelog ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
In a step to consolidate the code for fetching the PM-runtime
active/suspended time for a device, add a common function for that
and make the existing pm_runtime_suspended_time() call it.
Also add a corresponding pm_runtime_active_time() calling the new
common function.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
[ rjw: Changelog, function rename ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Here is the big driver core patchset for 5.1-rc1
More patches than "normal" here this merge window, due to some work in
the driver core by Alexander Duyck to rework the async probe
functionality to work better for a number of devices, and independant
work from Rafael for the device link functionality to make it work
"correctly".
Also in here is:
- lots of BUS_ATTR() removals, the macro is about to go away
- firmware test fixups
- ihex fixups and simplification
- component additions (also includes i915 patches)
- lots of minor coding style fixups and cleanups.
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXH+euQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynyTgCfbV8CLums843sBnT8NnWrTMTdTCcAn1K4re0m
ep8g+6oRLxJy414hogxQ
=bLs2
-----END PGP SIGNATURE-----
Merge tag 'driver-core-5.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg KH:
"Here is the big driver core patchset for 5.1-rc1
More patches than "normal" here this merge window, due to some work in
the driver core by Alexander Duyck to rework the async probe
functionality to work better for a number of devices, and independant
work from Rafael for the device link functionality to make it work
"correctly".
Also in here is:
- lots of BUS_ATTR() removals, the macro is about to go away
- firmware test fixups
- ihex fixups and simplification
- component additions (also includes i915 patches)
- lots of minor coding style fixups and cleanups.
All of these have been in linux-next for a while with no reported
issues"
* tag 'driver-core-5.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (65 commits)
driver core: platform: remove misleading err_alloc label
platform: set of_node in platform_device_register_full()
firmware: hardcode the debug message for -ENOENT
driver core: Add missing description of new struct device_link field
driver core: Fix PM-runtime for links added during consumer probe
drivers/component: kerneldoc polish
async: Add cmdline option to specify drivers to be async probed
driver core: Fix possible supplier PM-usage counter imbalance
PM-runtime: Fix __pm_runtime_set_status() race with runtime resume
driver: platform: Support parsing GpioInt 0 in platform_get_irq()
selftests: firmware: fix verify_reqs() return value
Revert "selftests: firmware: remove use of non-standard diff -Z option"
Revert "selftests: firmware: add CONFIG_FW_LOADER_USER_HELPER_FALLBACK to config"
device: Fix comment for driver_data in struct device
kernfs: Allocating memory for kernfs_iattrs with kmem_cache.
sysfs: remove unused include of kernfs-internal.h
driver core: Postpone DMA tear-down until after devres release
driver core: Document limitation related to DL_FLAG_RPM_ACTIVE
PM-runtime: Take suppliers into account in __pm_runtime_set_status()
device.h: Add __cold to dev_<level> logging functions
...
When rpm_resume() desactivates the autosuspend timer, it should only
try to cancel hrtimer but not wait for the handler to finish, because
both rpm_resume() and pm_suspend_timer_fn() take the power.lock.
A deadlock is possible as follows:
CPU0 CPU1
rpm_resume()
spin_lock_irqsave
pm_suspend_timer_fn()
spin_lock_irqsave
pm_runtime_deactivate_timer()
hrtimer_cancel()
It is sufficient to call hrtimer_try_to_cancel() from
pm_runtime_deactivate_timer(), because dev->power.timer_expires
reset to 0 by it, so use that function instead of hrtimer_cancel().
Fixes: 8234f6734c ("PM-runtime: Switch autosuspend over to using hrtimers")
Reported-by: Sunzhaosheng Sun(Zhaosheng) <sunzhaosheng@hisilicon.com>
Signed-off-by: Vincent Guittot <vincent.guittot@linaro.org>
[ rjw: Changelog ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Commit 4c06c4e6cf ("driver core: Fix possible supplier PM-usage
counter imbalance") introduced a regression that causes suppliers
to be suspended prematurely for device links added during consumer
driver probe if the initial PM-runtime status of the consumer is
"suspended" and the consumer is resumed after adding the link and
before pm_runtime_put_suppliers() is called. In that case,
pm_runtime_put_suppliers() will drop the rpm_active refcount for
the link by one and (since rpm_active is equal to two after the
preceding consumer resume) the supplier's PM-runtime usage counter
will be decremented, which may cause the supplier to suspend even
though the consumer's PM-runtime status is "active".
For this reason, partially revert commit 4c06c4e6cf as the problem
it tried to fix needs to be addressed somewhat differently, and
change pm_runtime_get_suppliers() and pm_runtime_put_suppliers() so
that the latter only drops rpm_active references acquired by the
former. [This requires adding a new field to struct device_link,
but I coulnd't find a cleaner way to address the issue that would
work in all cases.]
This causes pm_runtime_put_suppliers() to effectively ignore device
links added during consumer probe, so device_link_add() doesn't need
to worry about ensuring that suppliers will remain active after
pm_runtime_put_suppliers() for links created with DL_FLAG_RPM_ACTIVE
set and it only needs to bump up rpm_active by one for those links,
so pm_runtime_active_link() is not necessary any more.
Fixes: 4c06c4e6cf ("driver core: Fix possible supplier PM-usage counter imbalance")
Reported-by: Jon Hunter <jonathanh@nvidia.com>
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Tested-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If a stateless device link to a certain supplier with
DL_FLAG_PM_RUNTIME set in the flags is added and then removed by the
consumer driver's probe callback, the supplier's PM-runtime usage
counter will be nonzero after that which effectively causes the
supplier to remain "always on" going forward.
Namely, device_link_add() called to add the link invokes
device_link_rpm_prepare() which notices that the consumer driver is
probing, so it increments the supplier's PM-runtime usage counter
with the assumption that the link will stay around until
pm_runtime_put_suppliers() is called by driver_probe_device(),
but if the link goes away before that point, the supplier's
PM-runtime usage counter will remain nonzero.
To prevent that from happening, first rework pm_runtime_get_suppliers()
and pm_runtime_put_suppliers() to use the rpm_active refounts of device
links and make the latter only drop rpm_active and the supplier's
PM-runtime usage counter for each link by one, unless rpm_active is
one already for it. Next, modify device_link_add() to bump up the
new link's rpm_active refcount and the suppliers PM-runtime usage
counter by two, to prevent pm_runtime_put_suppliers(), if it is
called subsequently, from suspending the supplier prematurely (in
case its PM-runtime usage counter goes down to 0 in there).
Due to the way rpm_put_suppliers() works, this change does not
affect runtime suspend of the consumer ends of new device links (or,
generally, device links for which DL_FLAG_PM_RUNTIME has just been
set).
Fixes: e2f3cd831a ("driver core: Fix handling of runtime PM flags in device_link_add()")
Reported-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 4080ab0830 ("PM-runtime: Take suppliers into account in
__pm_runtime_set_status()") introduced a race condition that may
trigger if __pm_runtime_set_status() is used incorrectly (that is,
if it is called when PM-runtime is enabled for the target device
and working).
In that case, if the original PM-runtime status of the device is
RPM_SUSPENDED, a runtime resume of the device may occur after
__pm_runtime_set_status() has dropped its power.lock spinlock
and before deactivating its suppliers, so the suppliers may be
deactivated while the device is PM-runtime-active which may lead
to functional issues.
To avoid that, modify __pm_runtime_set_status() to check whether
or not PM-runtime is enabled for the device before activating its
suppliers (if the new status is RPM_ACTIVE) and either return an
error if that's the case or increment the device's disable_depth
counter to prevent PM-runtime from being enabled for it while
the remaining part of the function is running (disable_depth is
then decremented on the way out).
Fixes: 4080ab0830 ("PM-runtime: Take suppliers into account in __pm_runtime_set_status()")
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the target device has any suppliers, as reflected by device links
to them, __pm_runtime_set_status() does not take them into account,
which is not consistent with the other parts of the PM-runtime
framework and may lead to programming mistakes.
Modify __pm_runtime_set_status() to take suppliers into account by
activating them upfront if the new status is RPM_ACTIVE and
deactivating them on exit if the new status is RPM_SUSPENDED.
If the activation of one of the suppliers fails, the new status
will be RPM_SUSPENDED and the (remaining) suppliers will be
deactivated on exit (the child count of the device's parent
will be dropped too then).
Of course, adding device links locking to __pm_runtime_set_status()
means that it cannot be run fron interrupt context, so make it use
spin_lock_irq() and spin_unlock_irq() instead of spin_lock_irqsave()
and spin_unlock_irqrestore(), respectively.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Update the accounting_timestamp field only when PM runtime is enabled
and don't forget to account the last state before disabling it.
Suggested-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Vincent Guittot <vincent.guittot@linaro.org>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
[ rjw: Minor cleanups ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Similar to what happened whith autosuspend, a deadlock has been
reported with PM-runtime accounting in the call path:
change_clocksource
...
write_seqcount_begin
...
timekeeping_update
...
sh_cmt_clocksource_enable
...
rpm_resume
update_pm_runtime_accounting
ktime_get
do
read_seqcount_begin
while read_seqcount_retry
....
write_seqcount_end
Make PM-runtime accounting use ktime_get_mono_fast_ns() to avoid this
problem.
With ktime_get_mono_fast_ns(), the timestamp is not guaranteed to be
monotonic across an update of timekeeping and as a result time can go
backward. Add a test to skip accounting for such situation which should
stay exceptional.
Fixes: a08c2a5a31 ("PM-runtime: Replace jiffies-based accounting with ktime-based accounting")
Reported-by: Biju Das <biju.das@bp.renesas.com>
Signed-off-by: Vincent Guittot <vincent.guittot@linaro.org>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
[ rjw: Subject, changelog, comment cleanup ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
pm_runtime_autosuspend_expiration calls ktime_get_mono_fast_ns()
even when its returned value may be unused. Therefore get the
current time later and remove gotos while there.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Vincent Guittot <vincent.guittot@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Calling rpm_put_suppliers() from pm_runtime_drop_link() is excessive
as it affects all suppliers of the consumer device and not just the
one pointed to by the device link being dropped. Worst case it may
cause the consumer device to stop working unexpectedly. Moreover, in
principle it is racy with respect to runtime PM of the consumer
device.
To avoid these problems drop runtime PM references on the particular
supplier pointed to by the link in question only and do that after
the link has been dropped from the consumer device's list of links to
suppliers, which is in device_link_free().
Fixes: a0504aecba ("PM / runtime: Drop usage count for suppliers at device link removal")
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After commit ead18c23c2 ("driver core: Introduce device links
reference counting"), if there is a link between the given supplier
and the given consumer already, device_link_add() will refcount it
and return it unconditionally without updating its flags. It is
possible, however, that the second (or any subsequent) caller of
device_link_add() for the same consumer-supplier pair will pass
DL_FLAG_PM_RUNTIME, possibly along with DL_FLAG_RPM_ACTIVE, in flags
to it and the existing link may not behave as expected then.
First, if DL_FLAG_PM_RUNTIME is not set in the existing link's flags
at all, it needs to be set like during the original initialization of
the link.
Second, if DL_FLAG_RPM_ACTIVE is passed to device_link_add() in flags
(in addition to DL_FLAG_PM_RUNTIME), the existing link should to be
updated to reflect the "active" runtime PM configuration of the
consumer-supplier pair and extra care must be taken here to avoid
possible destructive races with runtime PM of the consumer.
To that end, redefine the rpm_active field in struct device_link
as a refcount, initialize it to 1 and make rpm_resume() (for the
consumer) and device_link_add() increment it whenever they acquire
a runtime PM reference on the supplier device. Accordingly, make
rpm_suspend() (for the consumer) and pm_runtime_clean_up_links()
decrement it and drop runtime PM references to the supplier
device in a loop until rpm_active becones 1 again.
Fixes: ead18c23c2 ("driver core: Introduce device links reference counting")
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Replace jiffies-based accounting for runtime_active_time and
runtime_suspended_time with ktime-based accounting. This makes the
runtime debug counters inline with genpd and other PM subsytems which
use ktime-based accounting.
Timekeeping is initialized before driver_init(). It's only at that time
that PM-runtime can be enabled.
Signed-off-by: Thara Gopinath <thara.gopinath@linaro.org>
[switch from ktime to raw nsec]
Signed-off-by: Vincent Guittot <vincent.guittot@linaro.org>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Initializing accounting_timestamp to something different from 0 during
pm_runtime_init() doesn't make sense and puts an artificial ordering
constraint between timekeeping_init() and pm_runtime_init().
PM-runtime should start time accounting only when it is enabled and
discard the period when disabled.
Set accounting_timestamp to now when enabling PM-runtime.
Suggested-by: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Signed-off-by: Vincent Guittot <vincent.guittot@linaro.org>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
[ rjw: Subject & changelog ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
A deadlock has been seen when swicthing clocksources which use
PM-runtime. The call path is:
change_clocksource
...
write_seqcount_begin
...
timekeeping_update
...
sh_cmt_clocksource_enable
...
rpm_resume
pm_runtime_mark_last_busy
ktime_get
do
read_seqcount_begin
while read_seqcount_retry
....
write_seqcount_end
Although we should be safe because we haven't yet changed the
clocksource at that time, we can't do that because of seqcount
protection.
Use ktime_get_mono_fast_ns() instead which is lock safe for such
cases.
With ktime_get_mono_fast_ns, the timestamp is not guaranteed to be
monotonic across an update and as a result can goes backward.
According to update_fast_timekeeper() description: "In the worst
case, this can result is a slightly wrong timestamp (a few
nanoseconds)". For PM-runtime autosuspend, this means only that
the suspend decision may be slightly suboptimal.
Fixes: 8234f6734c ("PM-runtime: Switch autosuspend over to using hrtimers")
Reported-by: Biju Das <biju.das@bp.renesas.com>
Signed-off-by: Vincent Guittot <vincent.guittot@linaro.org>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Some drivers (like i915/drm) needs to get the accounted suspended time.
pm_runtime_suspended_time() will return the suspended accounted time
in ns unit.
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Vincent Guittot <vincent.guittot@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Cast autosuspend_delay to u64 to make sure that the full computation
of 'expires' or slack will be done in u64, even on 32bits arch.
Otherwise, any delay greater than 2^31 nsec can overflow if signed
32bits is used when converting delay from msec to nsec.
Fixes: 8234f6734c (PM-runtime: Switch autosuspend over to using hrtimers)
Reported-by: Tony Lindgren <tony@atomide.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Vincent Guittot <vincent.guittot@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
PM-runtime now uses the hrtimers infrastructure for autosuspend, however
comments still reference 'jiffies'.
Fixes: 8234f6734c (PM-runtime: Switch autosuspend over to using hrtimers)
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
PM-runtime uses the timer infrastructure for autosuspend. This implies
that the minimum time before autosuspending a device is in the range
of 1 tick included to 2 ticks excluded
-On arm64 this means between 4ms and 8ms with default jiffies
configuration
-And on arm, it is between 10ms and 20ms
These values are quite high for embedded systems which sometimes want
the duration to be in the range of 1 ms.
It is possible to switch autosuspend over to using hrtimers to get
finer granularity for short durations and take advantage of slack to
retain some margins and get long timeouts with minimum wakeups.
On an arm64 platform that uses 1ms for autosuspending timeout of its
GPU, idle power is reduced by 10% with hrtimer.
The latency impact on arm64 hikey octo cores is:
- mark_last_busy: from 1.11 us to 1.25 us
- rpm_suspend: from 15.54 us to 15.38 us
[Only the code path of rpm_suspend() that starts hrtimer has been
measured.]
arm64 image (arm64 default defconfig) decreases by around 3KB
with following details:
$ size vmlinux-timer
text data bss dec hex filename
12034646 6869268 386840 19290754 1265a82 vmlinux
$ size vmlinux-hrtimer
text data bss dec hex filename
12030550 6870164 387032 19287746 1264ec2 vmlinux
The latency impact on arm 32bits snowball dual cores is :
- mark_last_busy: from 0.31 us usec to 0.77 us
- rpm_suspend: from 6.83 us to 6.67 usec
The increase of the image for snowball platform that I used for
testing performance impact, is neglictable (244B).
$ size vmlinux-timer
text data bss dec hex filename
7157961 2119580 264120 9541661 91981d build-ux500/vmlinux
size vmlinux-hrtimer
text data bss dec hex filename
7157773 2119884 264248 9541905 919911 vmlinux-hrtimer
And arm 32bits image (multi_v7_defconfig) increases by around 1.7KB
with following details:
$ size vmlinux-timer
text data bss dec hex filename
13304443 6803420 402768 20510631 138f7a7 vmlinux
$ size vmlinux-hrtimer
text data bss dec hex filename
13304299 6805276 402768 20512343 138fe57 vmlinux
Signed-off-by: Vincent Guittot <vincent.guittot@linaro.org>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Revert commit 1e83786198 (PM / runtime: Fixup reference counting of
device link suppliers at probe), as it has introduced a regression
and the condition it was designed to address should be covered by the
existing code.
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
In the case consumer device is runtime resumed, while the link to the
supplier is removed, the earlier call to pm_runtime_get_sync() made from
rpm_get_suppliers() does not get properly balanced with a corresponding
call to pm_runtime_put(). This leads to that suppliers remains to be
runtime resumed forever, while they don't need to.
Let's fix the behaviour by calling rpm_put_suppliers() when dropping a
device link. Not that, since rpm_put_suppliers() checks the
link->rpm_active flag, we can correctly avoid to call pm_runtime_put() in
cases when we shouldn't.
Reported-by: Todor Tomov <todor.tomov@linaro.org>
Fixes: 21d5c57b37 (PM / runtime: Use device links)
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
In the driver core, before it invokes really_probe() it runtime resumes the
suppliers for the device via calling pm_runtime_get_suppliers(), which also
increases the runtime PM usage count for each of the available supplier.
This makes sense, as to be able to allow the consumer device to be probed
by its driver. However, if the driver decides to add a new supplier link
during ->probe(), hence updating the list of suppliers, the following call
to pm_runtime_put_suppliers(), invoked after really_probe() in the driver
core, we get into trouble.
More precisely, pm_runtime_put() gets called also for the new supplier(s),
which is wrong as the driver core, didn't trigger pm_runtime_get_sync() to
be called for it in the first place. In other words, the new supplier may
be runtime suspended even in cases when it shouldn't.
Fix this behaviour, by runtime resume suppliers according to the same
conditions as managed by the runtime PM core, when runtime resume callbacks
are being invoked.
Additionally, don't try to runtime suspend any of the suppliers after
really_probe(), but instead rely on that to happen via the consumer device,
when it becomes runtime suspended.
Fixes: 21d5c57b37 (PM / runtime: Use device links)
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The pm_runtime_force_suspend|resume() helpers currently requires the device
to at some level (PM domain, bus, etc), have the ->runtime_suspend|resume()
callbacks assigned for it, else -ENOSYS is returned as an error.
However, there are no reason for this requirement, so let's simply remove
it by allowing these callbacks to be NULL.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Modify pm_runtime_need_not_resume() to make it avoid taking
power.child_count for devices with power.ignore_children which
is consistent with the runtime PM usage of these fields.
Suggested-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
One of the limitations of pm_runtime_force_suspend/resume() is that
if a parent driver wants to use these functions, all of its child
drivers generally have to do that too because of the parent usage
counter manipulations necessary to get the correct state of the parent
during system-wide transitions to the working state (system resume).
However, that limitation turns out to be artificial, so remove it.
Namely, pm_runtime_force_suspend() only needs to update the children
counter of its parent (if there's is a parent) when the device can
stay in suspend after the subsequent system resume transition, as
that counter is correct already otherwise. Now, if the parent's
children counter is not updated, it is not necessary to increment
the parent's usage counter in that case any more, as long as the
children counters of devices are checked along with their usage
counters in order to decide whether or not the devices may be left
in suspend after the subsequent system resume transition.
Accordingly, modify pm_runtime_force_suspend() to only call
pm_runtime_set_suspended() for devices whose usage and children
counters are at the "no references" level (the runtime PM status
of the device needs to be updated to "suspended" anyway in case
this function is called once again for the same device during the
transition under way), drop the parent usage counter incrementation
from it and update pm_runtime_force_resume() to compensate for these
changes.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Prevent rpm_get_suppliers() from returning an error code if runtime
PM is disabled for one or more of the supplier devices it wants to
runtime-resume, so as to make runtime PM work for devices with links
to suppliers that don't use runtime PM (such links may be created
during device enumeration even before it is known whether or not
runtime PM will be enabled for the devices in question, for example).
Fixes: 21d5c57b37 (PM / runtime: Use device links)
Reported-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Lukas Wunner <lukas@wunner.de>
Tested-by: Adrian Hunter <adrian.hunter@intel.com>
The check for "active" children in __pm_runtime_set_status(), when
trying to set the parent device status to "suspended", doesn't
really make sense, because in fact it is not invalid to set the
status of a device with runtime PM disabled to "suspended" in any
case. It is invalid to enable runtime PM for a device with its
status set to "suspended" while its child_count reference counter
is nonzero, but the check in __pm_runtime_set_status() doesn't
really cover that situation.
For this reason, drop the children check from __pm_runtime_set_status()
and add a check against child_count reference counters of "suspended"
devices to pm_runtime_enable().
Fixes: a8636c8964 (PM / Runtime: Don't allow to suspend a device with an active child)
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Johan Hovold <johan@kernel.org>
- Relocate the OPP (Operating Performance Points) framework to its
own directory under drivers/ and add support for power domain
performance states to it (Viresh Kumar).
- Modify the PM core, the PCI bus type and the ACPI PM domain to
support power management driver flags allowing device drivers to
specify their capabilities and preferences regarding the handling
of devices with enabled runtime PM during system suspend/resume
and clean up that code somewhat (Rafael Wysocki, Ulf Hansson).
- Add frequency-invariant accounting support to the task scheduler
on ARM and ARM64 (Dietmar Eggemann).
- Fix PM QoS device resume latency framework to prevent "no
restriction" requests from overriding requests with specific
requirements and drop the confusing PM_QOS_FLAG_REMOTE_WAKEUP
device PM QoS flag (Rafael Wysocki).
- Drop legacy class suspend/resume operations from the PM core
and drop legacy bus type suspend and resume callbacks from
ARM/locomo (Rafael Wysocki).
- Add min/max frequency support to devfreq and clean it up
somewhat (Chanwoo Choi).
- Rework wakeup support in the generic power domains (genpd)
framework and update some of its users accordingly (Geert
Uytterhoeven).
- Convert timers in the PM core to use timer_setup() (Kees Cook).
- Add support for exposing the SLP_S0 (Low Power S0 Idle)
residency counter based on the LPIT ACPI table on Intel
platforms (Srinivas Pandruvada).
- Add per-CPU PM QoS resume latency support to the ladder cpuidle
governor (Ramesh Thomas).
- Fix a deadlock between the wakeup notify handler and the
notifier removal in the ACPI core (Ville Syrjälä).
- Fix a cpufreq schedutil governor issue causing it to use
stale cached frequency values sometimes (Viresh Kumar).
- Fix an issue in the system suspend core support code causing
wakeup events detection to fail in some cases (Rajat Jain).
- Fix the generic power domains (genpd) framework to prevent
the PM core from using the direct-complete optimization with
it as that is guaranteed to fail (Ulf Hansson).
- Fix a minor issue in the cpuidle core and clean it up a bit
(Gaurav Jindal, Nicholas Piggin).
- Fix and clean up the intel_idle and ARM cpuidle drivers (Jason
Baron, Len Brown, Leo Yan).
- Fix a couple of minor issues in the OPP framework and clean it
up (Arvind Yadav, Fabio Estevam, Sudeep Holla, Tobias Jordan).
- Fix and clean up some cpufreq drivers and fix a minor issue in
the cpufreq statistics code (Arvind Yadav, Bhumika Goyal, Fabio
Estevam, Gautham Shenoy, Gustavo Silva, Marek Szyprowski, Masahiro
Yamada, Robert Jarzmik, Zumeng Chen).
- Fix minor issues in the system suspend and hibernation core, in
power management documentation and in the AVS (Adaptive Voltage
Scaling) framework (Helge Deller, Himanshu Jha, Joe Perches,
Rafael Wysocki).
- Fix some issues in the cpupower utility and document that Shuah
Khan is going to maintain it going forward (Prarit Bhargava,
Shuah Khan).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQIcBAABCAAGBQJaCg2eAAoJEILEb/54YlRxGhAP/26D5TvfQ65wtf2W0Gas/tsP
+24SzCLQO2GWalhbOXZbXhnBn/eCovKB6T8VB0V7Bff0VcUOK9szmBu9hOBJfXGN
ec2oYKtWPwqzkgPfbqjZhQTp5EXg/dmWYOhAMA7HLMv7oVZqoRZ/MNOJPooXAmQj
NEVWj3Eap0anic0ZgGMN4FaIMF6CHP2rAheqWQVXihhXpjIOWrJCjEoPZfbH1bFC
+zd9Batd3rq+eZ5dYxg+znpYcZi69kmPw+KASYsaWTJzNjYbR+VLOxqzx7Icdgbz
4glwWNe7lZGCAj+BIKGaHN5CR/fAXqkPvJ8csn6qISyUJ1Gph6otRfvuUaK58F4T
1Rmcj+mGXgJBcjaQGmVQIITKD6drBW/l50MJlze5JUM4A7VM2Di/cctgoWmOJsnO
2f6D6PYGuW0Fe8uUVGki/ddApXvoTGbEx+ncQ5+At+mLMKJwYfND9h2stOkCcrTy
k4Pr+XpVU9hXwYVX3a1Au41bFQiXYwguxD1TH1LaY3liAWXvo0qNc/Ib6mW8e7pL
wqPoe2/yxgVw5rsQPcKxVxAFFgjAAIdU3Xw44ETTPN315CLOoiuZgWkeTrnYCdix
DaBWu1VN9tU5U6FWBlWXDb06i5qvSo3aYzLnSBC6fm7qX2SuDxGiQTcyOQ7H1NiQ
d1wzhgObW98N7rZRaByu
=QTnx
-----END PGP SIGNATURE-----
Merge tag 'pm-4.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management updates from Rafael Wysocki:
"There are no real big ticket items here this time.
The most noticeable change is probably the relocation of the OPP
(Operating Performance Points) framework to its own directory under
drivers/ as it has grown big enough for that. Also Viresh is now going
to maintain it and send pull requests for it to me, so you will see
this change in the git history going forward (but still not right
now).
Another noticeable set of changes is the modifications of the PM core,
the PCI subsystem and the ACPI PM domain to allow of more integration
between system-wide suspend/resume and runtime PM. For now it's just a
way to avoid resuming devices from runtime suspend unnecessarily
during system suspend (if the driver sets a flag to indicate its
readiness for that) and in the works is an analogous mechanism to
allow devices to stay suspended after system resume.
In addition to that, we have some changes related to supporting
frequency-invariant CPU utilization metrics in the scheduler and in
the schedutil cpufreq governor on ARM and changes to add support for
device performance states to the generic power domains (genpd)
framework.
The rest is mostly fixes and cleanups of various sorts.
Specifics:
- Relocate the OPP (Operating Performance Points) framework to its
own directory under drivers/ and add support for power domain
performance states to it (Viresh Kumar).
- Modify the PM core, the PCI bus type and the ACPI PM domain to
support power management driver flags allowing device drivers to
specify their capabilities and preferences regarding the handling
of devices with enabled runtime PM during system suspend/resume and
clean up that code somewhat (Rafael Wysocki, Ulf Hansson).
- Add frequency-invariant accounting support to the task scheduler on
ARM and ARM64 (Dietmar Eggemann).
- Fix PM QoS device resume latency framework to prevent "no
restriction" requests from overriding requests with specific
requirements and drop the confusing PM_QOS_FLAG_REMOTE_WAKEUP
device PM QoS flag (Rafael Wysocki).
- Drop legacy class suspend/resume operations from the PM core and
drop legacy bus type suspend and resume callbacks from ARM/locomo
(Rafael Wysocki).
- Add min/max frequency support to devfreq and clean it up somewhat
(Chanwoo Choi).
- Rework wakeup support in the generic power domains (genpd)
framework and update some of its users accordingly (Geert
Uytterhoeven).
- Convert timers in the PM core to use timer_setup() (Kees Cook).
- Add support for exposing the SLP_S0 (Low Power S0 Idle) residency
counter based on the LPIT ACPI table on Intel platforms (Srinivas
Pandruvada).
- Add per-CPU PM QoS resume latency support to the ladder cpuidle
governor (Ramesh Thomas).
- Fix a deadlock between the wakeup notify handler and the notifier
removal in the ACPI core (Ville Syrjälä).
- Fix a cpufreq schedutil governor issue causing it to use stale
cached frequency values sometimes (Viresh Kumar).
- Fix an issue in the system suspend core support code causing wakeup
events detection to fail in some cases (Rajat Jain).
- Fix the generic power domains (genpd) framework to prevent the PM
core from using the direct-complete optimization with it as that is
guaranteed to fail (Ulf Hansson).
- Fix a minor issue in the cpuidle core and clean it up a bit (Gaurav
Jindal, Nicholas Piggin).
- Fix and clean up the intel_idle and ARM cpuidle drivers (Jason
Baron, Len Brown, Leo Yan).
- Fix a couple of minor issues in the OPP framework and clean it up
(Arvind Yadav, Fabio Estevam, Sudeep Holla, Tobias Jordan).
- Fix and clean up some cpufreq drivers and fix a minor issue in the
cpufreq statistics code (Arvind Yadav, Bhumika Goyal, Fabio
Estevam, Gautham Shenoy, Gustavo Silva, Marek Szyprowski, Masahiro
Yamada, Robert Jarzmik, Zumeng Chen).
- Fix minor issues in the system suspend and hibernation core, in
power management documentation and in the AVS (Adaptive Voltage
Scaling) framework (Helge Deller, Himanshu Jha, Joe Perches, Rafael
Wysocki).
- Fix some issues in the cpupower utility and document that Shuah
Khan is going to maintain it going forward (Prarit Bhargava, Shuah
Khan)"
* tag 'pm-4.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (88 commits)
tools/power/cpupower: add libcpupower.so.0.0.1 to .gitignore
tools/power/cpupower: Add 64 bit library detection
intel_idle: Graceful probe failure when MWAIT is disabled
cpufreq: schedutil: Reset cached_raw_freq when not in sync with next_freq
freezer: Fix typo in freezable_schedule_timeout() comment
PM / s2idle: Clear the events_check_enabled flag
cpufreq: stats: Handle the case when trans_table goes beyond PAGE_SIZE
cpufreq: arm_big_little: make cpufreq_arm_bL_ops structures const
cpufreq: arm_big_little: make function arguments and structure pointer const
cpuidle: Avoid assignment in if () argument
cpuidle: Clean up cpuidle_enable_device() error handling a bit
ACPI / PM: Fix acpi_pm_notifier_lock vs flush_workqueue() deadlock
PM / Domains: Fix genpd to deal with drivers returning 1 from ->prepare()
cpuidle: ladder: Add per CPU PM QoS resume latency support
PM / QoS: Fix device resume latency framework
PM / domains: Rework governor code to be more consistent
PM / Domains: Remove gpd_dev_ops.active_wakeup() callback
soc: rockchip: power-domain: Use GENPD_FLAG_ACTIVE_WAKEUP
soc: mediatek: Use GENPD_FLAG_ACTIVE_WAKEUP
ARM: shmobile: pm-rmobile: Use GENPD_FLAG_ACTIVE_WAKEUP
...
* pm-core:
ACPI / PM: Take SMART_SUSPEND driver flag into account
PCI / PM: Take SMART_SUSPEND driver flag into account
PCI / PM: Drop unnecessary invocations of pcibios_pm_ops callbacks
PM / core: Add SMART_SUSPEND driver flag
PCI / PM: Use the NEVER_SKIP driver flag
PM / core: Add NEVER_SKIP and SMART_PREPARE driver flags
PM / core: Convert timers to use timer_setup()
PM / core: Fix kerneldoc comments of four functions
PM / core: Drop legacy class suspend/resume operations
The special value of 0 for device resume latency PM QoS means
"no restriction", but there are two problems with that.
First, device resume latency PM QoS requests with 0 as the
value are always put in front of requests with positive
values in the priority lists used internally by the PM QoS
framework, causing 0 to be chosen as an effective constraint
value. However, that 0 is then interpreted as "no restriction"
effectively overriding the other requests with specific
restrictions which is incorrect.
Second, the users of device resume latency PM QoS have no
way to specify that *any* resume latency at all should be
avoided, which is an artificial limitation in general.
To address these issues, modify device resume latency PM QoS to
use S32_MAX as the "no constraint" value and 0 as the "no
latency at all" one and rework its users (the cpuidle menu
governor, the genpd QoS governor and the runtime PM framework)
to follow these changes.
Also add a special "n/a" value to the corresponding user space I/F
to allow user space to indicate that it cannot accept any resume
latencies at all for the given device.
Fixes: 85dc0b8a40 (PM / QoS: Make it possible to expose PM QoS latency constraints)
Link: https://bugzilla.kernel.org/show_bug.cgi?id=197323
Reported-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Tested-by: Reinette Chatre <reinette.chatre@intel.com>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Tero Kristo <t-kristo@ti.com>
Reviewed-by: Ramesh Thomas <ramesh.thomas@intel.com>
Please do not apply this to mainline directly, instead please re-run the
coccinelle script shown below and apply its output.
For several reasons, it is desirable to use {READ,WRITE}_ONCE() in
preference to ACCESS_ONCE(), and new code is expected to use one of the
former. So far, there's been no reason to change most existing uses of
ACCESS_ONCE(), as these aren't harmful, and changing them results in
churn.
However, for some features, the read/write distinction is critical to
correct operation. To distinguish these cases, separate read/write
accessors must be used. This patch migrates (most) remaining
ACCESS_ONCE() instances to {READ,WRITE}_ONCE(), using the following
coccinelle script:
----
// Convert trivial ACCESS_ONCE() uses to equivalent READ_ONCE() and
// WRITE_ONCE()
// $ make coccicheck COCCI=/home/mark/once.cocci SPFLAGS="--include-headers" MODE=patch
virtual patch
@ depends on patch @
expression E1, E2;
@@
- ACCESS_ONCE(E1) = E2
+ WRITE_ONCE(E1, E2)
@ depends on patch @
expression E;
@@
- ACCESS_ONCE(E)
+ READ_ONCE(E)
----
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: davem@davemloft.net
Cc: linux-arch@vger.kernel.org
Cc: mpe@ellerman.id.au
Cc: shuah@kernel.org
Cc: snitzer@redhat.com
Cc: thor.thayer@linux.intel.com
Cc: tj@kernel.org
Cc: viro@zeniv.linux.org.uk
Cc: will.deacon@arm.com
Link: http://lkml.kernel.org/r/1508792849-3115-19-git-send-email-paulmck@linux.vnet.ibm.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly. Removes test of .data field, since
that will be going away.
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Bhaskar Chowdhury
Rafael J. Wysocki
Xiang Chen
Andy Shevchenko
Sakari Ailus
Michał Mirosław
Linus Torvalds
Joel Fernandes (Google)
Viresh Kumar
Greg Kroah-Hartman
Ulf Hansson
Vincent Guittot
Ladislav Michl
Thara Gopinath
Mark Rutland
Kees Cook