Usage is as follows:
myled=ledname
tty=ttyS0
echo tty > /sys/class/leds/$myled/trigger
echo $tty > /sys/class/leds/$myled/ttyname
. When this new trigger is active it periodically checks the tty's
statistics and when it changed since the last check the led is flashed
once.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20210113173018.bq2fkea2o3yp6rf6@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds a new LED trigger for coupling the audio mixer change
with the LED on laptops or other devices. Currently there are two
trigger types, "audio-mute" and "audio-micmute".
The audio driver triggers the LED brightness change via
ledtrig_audio_set() call with the proper type (either mute or
mic-mute). OTOH, the consumers may call ledtrig_audio_get() for the
initial brightness value that may have been set by the audio driver
beforehand.
This new stuff will be used by HD-audio codec driver and some platform
drivers (thinkpad_acpi and dell-laptop, also upcoming huawei-wmi).
Acked-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Acked-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch adds a new LED trigger that LED device can configure
to employ software or hardware pattern engine.
Consumers can write 'pattern' file to enable the software pattern
which alters the brightness for the specified duration with one
software timer.
Moreover consumers can write 'hw_pattern' file to enable the hardware
pattern for some LED controllers which can autonomously control
brightness over time, according to some preprogrammed hardware
patterns.
Signed-off-by: Raphael Teysseyre <rteysseyre@gmail.com>
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
This commit introduces a NETDEV trigger for named device
activity. Available triggers are link, rx, and tx.
Signed-off-by: Ben Whitten <ben.whitten@gmail.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=T2rn
-----END PGP SIGNATURE-----
Merge tag 'leds_for_4.15rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/j.anaszewski/linux-leds
Pull LED updates from Jacek Anaszewski:
"New LED class driver:
- add a driver for PC Engines APU/APU2 LEDs
New LED trigger:
- add a system activity LED trigger
LED core improvements:
- replace flags bit shift with BIT() macros
Convert timers to use timer_setup() in:
- led-core
- ledtrig-activity
- ledtrig-heartbeat
- ledtrig-transient
LED class drivers fixes:
- lp55xx: fix spelling mistake: 'cound' -> 'could'
- tca6507: Remove unnecessary reg check
- pca955x: Don't invert requested value in pca955x_gpio_set_value()
LED documentation improvements:
- update 00-INDEX file"
* tag 'leds_for_4.15rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/j.anaszewski/linux-leds:
leds: Add driver for PC Engines APU/APU2 LEDs
leds: lp55xx: fix spelling mistake: 'cound' -> 'could'
leds: Convert timers to use timer_setup()
Documentation: leds: Update 00-INDEX file
leds: tca6507: Remove unnecessary reg check
leds: ledtrig-heartbeat: Convert timers to use timer_setup()
leds: Replace flags bit shift with BIT() macros
leds: pca955x: Don't invert requested value in pca955x_gpio_set_value()
leds: ledtrig-activity: Add a system activity LED trigger
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The "activity" trigger was inspired by the heartbeat one, but aims at
providing instant indication of the immediate CPU usage. Under idle
condition, it flashes 10ms every second. At 100% usage, it flashes
90ms every 100ms. The blinking frequency increases from 1 to 10 Hz
until either the load is high enough to saturate one CPU core or 50%
load is reached on a single-core system. Then past this point only the
duty cycle increases from 10 to 90%.
This results in a very visible activity reporting allowing one to
immediately tell whether a machine is under load or not, making it
quite suitable to be used in clusters.
Signed-off-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
This patch converts the IDE specific LED trigger to a generic disk
activity LED trigger. The libata core is now a trigger source just
like before the IDE disk driver. It's merely a replacement of the
string ide by disk.
The patch is taken from http://dev.gentoo.org/~josejx/ata.patch and is
widely used by any ibook/powerbook owners with great satisfaction.
Likewise, it is very often used successfully on different ARM platforms.
Unlike the original patch, the existing 'ide-disk' trigger is still
available for backward compatibility. That reduce the amount of patches
in affected device trees out of the mainline kernel. For further
development, the new name 'disk-activity' should be used.
Cc: Joseph Jezak <josejx@gentoo.org>
Cc: Jörg Sommer <joerg@alea.gnuu.de>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Stephan Linz <linz@li-pro.net>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
This commit introduces a MTD trigger for flash (NAND/NOR) device
activity. The implementation is copied from IDE disk.
This trigger deprecates the "nand-disk" LED trigger, but for backwards
compatibility, we still keep the "nand-disk" trigger around.
The motivation for deprecating the "nand-disk" LED trigger is that
it only works for NAND drivers, whereas the "mtd" LED trigger
is more generic (in fact, "nand-disk" currently only works for
certain NAND drivers).
Signed-off-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
This commit introduces a new LED trigger which allows to configure
a LED to blink on a kernel panic (through panic_blink).
Notice that currently the Openmoko FreeRunner (GTA02) mach code
sets panic_blink to blink a hard-coded LED. The new trigger is
meant to introduce a generic mechanism to achieve this.
Signed-off-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Some LED devices support flash/torch functionality through the LED subsystem.
This patch enables direct LED trigger controls by the driver.
Flash on/off and torch on/off can be done simply by other driver space.
Two trigger APIs are added, ledtrig_flash_ctrl() and ledtrig_torch_ctrl().
Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
For better driver management, new subdirectory, 'trigger' is created.
All LED trigger drivers are moved into this directory.
Internal header, 'leds.h' is included in each LED trigger drivers.
Fix the location of header file, "leds.h" -> "../leds.h" in driver files.
One exception is here, 'ledtrig-timer.c'.
There is no need to include 'leds.h'. so '#include "leds.h"' line was removed.
Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
Uwe Kleine-König
Takashi Iwai
Baolin Wang
Ben Whitten
Linus Torvalds
Greg Kroah-Hartman
Willy Tarreau
Stephan Linz
Ezequiel Garcia
Kim, Milo