Pull networking updates from David Miller:
"Another merge window, another pull full of stuff:
1) Support alternative names for network devices, from Jiri Pirko.
2) Introduce per-netns netdev notifiers, also from Jiri Pirko.
3) Support MSG_PEEK in vsock/virtio, from Matias Ezequiel Vara
Larsen.
4) Allow compiling out the TLS TOE code, from Jakub Kicinski.
5) Add several new tracepoints to the kTLS code, also from Jakub.
6) Support set channels ethtool callback in ena driver, from Sameeh
Jubran.
7) New SCTP events SCTP_ADDR_ADDED, SCTP_ADDR_REMOVED,
SCTP_ADDR_MADE_PRIM, and SCTP_SEND_FAILED_EVENT. From Xin Long.
8) Add XDP support to mvneta driver, from Lorenzo Bianconi.
9) Lots of netfilter hw offload fixes, cleanups and enhancements,
from Pablo Neira Ayuso.
10) PTP support for aquantia chips, from Egor Pomozov.
11) Add UDP segmentation offload support to igb, ixgbe, and i40e. From
Josh Hunt.
12) Add smart nagle to tipc, from Jon Maloy.
13) Support L2 field rewrite by TC offloads in bnxt_en, from Venkat
Duvvuru.
14) Add a flow mask cache to OVS, from Tonghao Zhang.
15) Add XDP support to ice driver, from Maciej Fijalkowski.
16) Add AF_XDP support to ice driver, from Krzysztof Kazimierczak.
17) Support UDP GSO offload in atlantic driver, from Igor Russkikh.
18) Support it in stmmac driver too, from Jose Abreu.
19) Support TIPC encryption and auth, from Tuong Lien.
20) Introduce BPF trampolines, from Alexei Starovoitov.
21) Make page_pool API more numa friendly, from Saeed Mahameed.
22) Introduce route hints to ipv4 and ipv6, from Paolo Abeni.
23) Add UDP segmentation offload to cxgb4, Rahul Lakkireddy"
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (1857 commits)
libbpf: Fix usage of u32 in userspace code
mm: Implement no-MMU variant of vmalloc_user_node_flags
slip: Fix use-after-free Read in slip_open
net: dsa: sja1105: fix sja1105_parse_rgmii_delays()
macvlan: schedule bc_work even if error
enetc: add support Credit Based Shaper(CBS) for hardware offload
net: phy: add helpers phy_(un)lock_mdio_bus
mdio_bus: don't use managed reset-controller
ax88179_178a: add ethtool_op_get_ts_info()
mlxsw: spectrum_router: Fix use of uninitialized adjacency index
mlxsw: spectrum_router: After underlay moves, demote conflicting tunnels
bpf: Simplify __bpf_arch_text_poke poke type handling
bpf: Introduce BPF_TRACE_x helper for the tracing tests
bpf: Add bpf_jit_blinding_enabled for !CONFIG_BPF_JIT
bpf, testing: Add various tail call test cases
bpf, x86: Emit patchable direct jump as tail call
bpf: Constant map key tracking for prog array pokes
bpf: Add poke dependency tracking for prog array maps
bpf: Add initial poke descriptor table for jit images
bpf: Move owner type, jited info into array auxiliary data
...
- On ARMv8 CPUs without hardware updates of the access flag, avoid
failing cow_user_page() on PFN mappings if the pte is old. The patches
introduce an arch_faults_on_old_pte() macro, defined as false on x86.
When true, cow_user_page() makes the pte young before attempting
__copy_from_user_inatomic().
- Covert the synchronous exception handling paths in
arch/arm64/kernel/entry.S to C.
- FTRACE_WITH_REGS support for arm64.
- ZONE_DMA re-introduced on arm64 to support Raspberry Pi 4
- Several kselftest cases specific to arm64, together with a MAINTAINERS
update for these files (moved to the ARM64 PORT entry).
- Workaround for a Neoverse-N1 erratum where the CPU may fetch stale
instructions under certain conditions.
- Workaround for Cortex-A57 and A72 errata where the CPU may
speculatively execute an AT instruction and associate a VMID with the
wrong guest page tables (corrupting the TLB).
- Perf updates for arm64: additional PMU topologies on HiSilicon
platforms, support for CCN-512 interconnect, AXI ID filtering in the
IMX8 DDR PMU, support for the CCPI2 uncore PMU in ThunderX2.
- GICv3 optimisation to avoid a heavy barrier when accessing the
ICC_PMR_EL1 register.
- ELF HWCAP documentation updates and clean-up.
- SMC calling convention conduit code clean-up.
- KASLR diagnostics printed during boot
- NVIDIA Carmel CPU added to the KPTI whitelist
- Some arm64 mm clean-ups: use generic free_initrd_mem(), remove stale
macro, simplify calculation in __create_pgd_mapping(), typos.
- Kconfig clean-ups: CMDLINE_FORCE to depend on CMDLINE, choice for
endinanness to help with allmodconfig.
-----BEGIN PGP SIGNATURE-----
iQIzBAABCgAdFiEE5RElWfyWxS+3PLO2a9axLQDIXvEFAl3YJswACgkQa9axLQDI
XvFwYg//aTGhNLew3ADgW2TYal7LyqetRROixPBrzqHLu2A8No1+QxHMaKxpZVyf
pt25tABuLtPHql3qBzE0ltmfbLVsPj/3hULo404EJb9HLRfUnVGn7gcPkc+p4YAr
IYkYPXJbk6OlJ84vI+4vXmDEF12bWCqamC9qZ+h99qTpMjFXFO17DSJ7xQ8Xic3A
HHgCh4uA7gpTVOhLxaS6KIw+AZNYwvQxLXch2+wj6agbGX79uw9BeMhqVXdkPq8B
RTDJpOdS970WOT4cHWOkmXwsqqGRqgsgyu+bRUJ0U72+0y6MX0qSHIUnVYGmNc5q
Dtox4rryYLvkv/hbpkvjgVhv98q3J1mXt/CalChWB5dG4YwhJKN2jMiYuoAvB3WS
6dR7Dfupgai9gq1uoKgBayS2O6iFLSa4g58vt3EqUBqmM7W7viGFPdLbuVio4ycn
CNF2xZ8MZR6Wrh1JfggO7Hc11EJdSqESYfHO6V/pYB4pdpnqJLDoriYHXU7RsZrc
HvnrIvQWKMwNbqBvpNbWvK5mpBMMX2pEienA3wOqKNH7MbepVsG+npOZTVTtl9tN
FL0ePb/mKJu/2+gW8ntiqYn7EzjKprRmknOiT2FjWWo0PxgJ8lumefuhGZZbaOWt
/aTAeD7qKd/UXLKGHF/9v3q4GEYUdCFOXP94szWVPyLv+D9h8L8=
=TPL9
-----END PGP SIGNATURE-----
Merge tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 updates from Catalin Marinas:
"Apart from the arm64-specific bits (core arch and perf, new arm64
selftests), it touches the generic cow_user_page() (reviewed by
Kirill) together with a macro for x86 to preserve the existing
behaviour on this architecture.
Summary:
- On ARMv8 CPUs without hardware updates of the access flag, avoid
failing cow_user_page() on PFN mappings if the pte is old. The
patches introduce an arch_faults_on_old_pte() macro, defined as
false on x86. When true, cow_user_page() makes the pte young before
attempting __copy_from_user_inatomic().
- Covert the synchronous exception handling paths in
arch/arm64/kernel/entry.S to C.
- FTRACE_WITH_REGS support for arm64.
- ZONE_DMA re-introduced on arm64 to support Raspberry Pi 4
- Several kselftest cases specific to arm64, together with a
MAINTAINERS update for these files (moved to the ARM64 PORT entry).
- Workaround for a Neoverse-N1 erratum where the CPU may fetch stale
instructions under certain conditions.
- Workaround for Cortex-A57 and A72 errata where the CPU may
speculatively execute an AT instruction and associate a VMID with
the wrong guest page tables (corrupting the TLB).
- Perf updates for arm64: additional PMU topologies on HiSilicon
platforms, support for CCN-512 interconnect, AXI ID filtering in
the IMX8 DDR PMU, support for the CCPI2 uncore PMU in ThunderX2.
- GICv3 optimisation to avoid a heavy barrier when accessing the
ICC_PMR_EL1 register.
- ELF HWCAP documentation updates and clean-up.
- SMC calling convention conduit code clean-up.
- KASLR diagnostics printed during boot
- NVIDIA Carmel CPU added to the KPTI whitelist
- Some arm64 mm clean-ups: use generic free_initrd_mem(), remove
stale macro, simplify calculation in __create_pgd_mapping(), typos.
- Kconfig clean-ups: CMDLINE_FORCE to depend on CMDLINE, choice for
endinanness to help with allmodconfig"
* tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux: (93 commits)
arm64: Kconfig: add a choice for endianness
kselftest: arm64: fix spelling mistake "contiguos" -> "contiguous"
arm64: Kconfig: make CMDLINE_FORCE depend on CMDLINE
MAINTAINERS: Add arm64 selftests to the ARM64 PORT entry
arm64: kaslr: Check command line before looking for a seed
arm64: kaslr: Announce KASLR status on boot
kselftest: arm64: fake_sigreturn_misaligned_sp
kselftest: arm64: fake_sigreturn_bad_size
kselftest: arm64: fake_sigreturn_duplicated_fpsimd
kselftest: arm64: fake_sigreturn_missing_fpsimd
kselftest: arm64: fake_sigreturn_bad_size_for_magic0
kselftest: arm64: fake_sigreturn_bad_magic
kselftest: arm64: add helper get_current_context
kselftest: arm64: extend test_init functionalities
kselftest: arm64: mangle_pstate_invalid_mode_el[123][ht]
kselftest: arm64: mangle_pstate_invalid_daif_bits
kselftest: arm64: mangle_pstate_invalid_compat_toggle and common utils
kselftest: arm64: extend toplevel skeleton Makefile
drivers/perf: hisi: update the sccl_id/ccl_id for certain HiSilicon platform
arm64: mm: reserve CMA and crashkernel in ZONE_DMA32
...
In order to use 128-bit integer arithmetic in C code, the architecture
needs to have declared support for it by setting ARCH_SUPPORTS_INT128,
and it requires a version of the toolchain that supports this at build
time. This is why all existing tests for ARCH_SUPPORTS_INT128 also test
whether __SIZEOF_INT128__ is defined, since this is only the case for
compilers that can support 128-bit integers.
Let's fold this additional test into the Kconfig declaration of
ARCH_SUPPORTS_INT128 so that we can also use the symbol in Makefiles,
e.g., to decide whether a certain object needs to be included in the
first place.
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
There are both positive and negative options about this feature.
At first, I thought it was a good idea, but actually Linus stated a
negative opinion (https://lkml.org/lkml/2019/9/29/227). I admit it
is ugly and annoying.
The baseline I'd like to keep is the compile-test of uapi headers.
(Otherwise, kernel developers have no way to ensure the correctness
of the exported headers.)
I will maintain a small build rule in usr/include/Makefile.
Remove the other header test functionality.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Drop various work-arounds we have for workqueues:
- We no longer need the async_list for tracking sequential IO.
- We don't have to maintain our own mm tracking/setting.
- We don't need a separate workqueue for buffered writes. This didn't
even work that well to begin with, as it was suboptimal for multiple
buffered writers on multiple files.
- We can properly cancel pending interruptible work. This fixes
deadlocks with particularly socket IO, where we cannot cancel them
when the io_uring is closed. Hence the ring will wait forever for
these requests to complete, which may never happen. This is different
from disk IO where we know requests will complete in a finite amount
of time.
- Due to being able to cancel work interruptible work that is already
running, we can implement file table support for work. We need that
for supporting system calls that add to a process file table.
- It gets us one step closer to adding async support for any system
call.
Signed-off-by: Jens Axboe <axboe@kernel.dk>
arm64 calls memblock_free() for the initrd area in its implementation of
free_initrd_mem(), but this call has no actual effect that late in the boot
process. By the time initrd is freed, all the reserved memory is managed by
the page allocator and the memblock.reserved is unused, so the only purpose
of the memblock_free() call is to keep track of initrd memory for debugging
and accounting.
Without the memblock_free() call the only difference between arm64 and the
generic versions of free_initrd_mem() is the memory poisoning.
Move memblock_free() call to the generic code, enable it there
for the architectures that define ARCH_KEEP_MEMBLOCK and use the generic
implementation of free_initrd_mem() on arm64.
Tested-by: Anshuman Khandual <anshuman.khandual@arm.com> #arm64
Reviewed-by: Anshuman Khandual <anshuman.khandual@arm.com>
Acked-by: Will Deacon <will@kernel.org>
Signed-off-by: Mike Rapoport <rppt@linux.ibm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Add a new virtual device named /dev/cifs (0xfe) to tell the kernel to
mount the root file system over the network by using SMB protocol.
cifs_root_data() will be responsible to retrieve the parsed
information of the new command-line option (cifsroot=) and then call
do_mount_root() with the appropriate mount options for cifs.ko.
Signed-off-by: Paulo Alcantara (SUSE) <pc@cjr.nz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull kernel lockdown mode from James Morris:
"This is the latest iteration of the kernel lockdown patchset, from
Matthew Garrett, David Howells and others.
From the original description:
This patchset introduces an optional kernel lockdown feature,
intended to strengthen the boundary between UID 0 and the kernel.
When enabled, various pieces of kernel functionality are restricted.
Applications that rely on low-level access to either hardware or the
kernel may cease working as a result - therefore this should not be
enabled without appropriate evaluation beforehand.
The majority of mainstream distributions have been carrying variants
of this patchset for many years now, so there's value in providing a
doesn't meet every distribution requirement, but gets us much closer
to not requiring external patches.
There are two major changes since this was last proposed for mainline:
- Separating lockdown from EFI secure boot. Background discussion is
covered here: https://lwn.net/Articles/751061/
- Implementation as an LSM, with a default stackable lockdown LSM
module. This allows the lockdown feature to be policy-driven,
rather than encoding an implicit policy within the mechanism.
The new locked_down LSM hook is provided to allow LSMs to make a
policy decision around whether kernel functionality that would allow
tampering with or examining the runtime state of the kernel should be
permitted.
The included lockdown LSM provides an implementation with a simple
policy intended for general purpose use. This policy provides a coarse
level of granularity, controllable via the kernel command line:
lockdown={integrity|confidentiality}
Enable the kernel lockdown feature. If set to integrity, kernel features
that allow userland to modify the running kernel are disabled. If set to
confidentiality, kernel features that allow userland to extract
confidential information from the kernel are also disabled.
This may also be controlled via /sys/kernel/security/lockdown and
overriden by kernel configuration.
New or existing LSMs may implement finer-grained controls of the
lockdown features. Refer to the lockdown_reason documentation in
include/linux/security.h for details.
The lockdown feature has had signficant design feedback and review
across many subsystems. This code has been in linux-next for some
weeks, with a few fixes applied along the way.
Stephen Rothwell noted that commit 9d1f8be5cf ("bpf: Restrict bpf
when kernel lockdown is in confidentiality mode") is missing a
Signed-off-by from its author. Matthew responded that he is providing
this under category (c) of the DCO"
* 'next-lockdown' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security: (31 commits)
kexec: Fix file verification on S390
security: constify some arrays in lockdown LSM
lockdown: Print current->comm in restriction messages
efi: Restrict efivar_ssdt_load when the kernel is locked down
tracefs: Restrict tracefs when the kernel is locked down
debugfs: Restrict debugfs when the kernel is locked down
kexec: Allow kexec_file() with appropriate IMA policy when locked down
lockdown: Lock down perf when in confidentiality mode
bpf: Restrict bpf when kernel lockdown is in confidentiality mode
lockdown: Lock down tracing and perf kprobes when in confidentiality mode
lockdown: Lock down /proc/kcore
x86/mmiotrace: Lock down the testmmiotrace module
lockdown: Lock down module params that specify hardware parameters (eg. ioport)
lockdown: Lock down TIOCSSERIAL
lockdown: Prohibit PCMCIA CIS storage when the kernel is locked down
acpi: Disable ACPI table override if the kernel is locked down
acpi: Ignore acpi_rsdp kernel param when the kernel has been locked down
ACPI: Limit access to custom_method when the kernel is locked down
x86/msr: Restrict MSR access when the kernel is locked down
x86: Lock down IO port access when the kernel is locked down
...
Pull integrity updates from Mimi Zohar:
"The major feature in this time is IMA support for measuring and
appraising appended file signatures. In addition are a couple of bug
fixes and code cleanup to use struct_size().
In addition to the PE/COFF and IMA xattr signatures, the kexec kernel
image may be signed with an appended signature, using the same
scripts/sign-file tool that is used to sign kernel modules.
Similarly, the initramfs may contain an appended signature.
This contained a lot of refactoring of the existing appended signature
verification code, so that IMA could retain the existing framework of
calculating the file hash once, storing it in the IMA measurement list
and extending the TPM, verifying the file's integrity based on a file
hash or signature (eg. xattrs), and adding an audit record containing
the file hash, all based on policy. (The IMA support for appended
signatures patch set was posted and reviewed 11 times.)
The support for appended signature paves the way for adding other
signature verification methods, such as fs-verity, based on a single
system-wide policy. The file hash used for verifying the signature and
the signature, itself, can be included in the IMA measurement list"
* 'next-integrity' of git://git.kernel.org/pub/scm/linux/kernel/git/zohar/linux-integrity:
ima: ima_api: Use struct_size() in kzalloc()
ima: use struct_size() in kzalloc()
sefltest/ima: support appended signatures (modsig)
ima: Fix use after free in ima_read_modsig()
MODSIGN: make new include file self contained
ima: fix freeing ongoing ahash_request
ima: always return negative code for error
ima: Store the measurement again when appraising a modsig
ima: Define ima-modsig template
ima: Collect modsig
ima: Implement support for module-style appended signatures
ima: Factor xattr_verify() out of ima_appraise_measurement()
ima: Add modsig appraise_type option for module-style appended signatures
integrity: Select CONFIG_KEYS instead of depending on it
PKCS#7: Introduce pkcs7_get_digest()
PKCS#7: Refactor verify_pkcs7_signature()
MODSIGN: Export module signature definitions
ima: initialize the "template" field with the default template
Replace open-coded bitmap array initialization of init_mm.cpu_bitmask with
neat CPU_BITS_NONE macro.
And, since init_mm.cpu_bitmask is statically set to zero, there is no way
to clear it again in start_kernel().
Link: http://lkml.kernel.org/r/1565703815-8584-1-git-send-email-rppt@linux.ibm.com
Signed-off-by: Mike Rapoport <rppt@linux.ibm.com>
Reviewed-by: Andrew Morton <akpm@linux-foundation.org>
Reviewed-by: David Hildenbrand <david@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Both pgtable_cache_init() and pgd_cache_init() are used to initialize kmem
cache for page table allocations on several architectures that do not use
PAGE_SIZE tables for one or more levels of the page table hierarchy.
Most architectures do not implement these functions and use __weak default
NOP implementation of pgd_cache_init(). Since there is no such default
for pgtable_cache_init(), its empty stub is duplicated among most
architectures.
Rename the definitions of pgd_cache_init() to pgtable_cache_init() and
drop empty stubs of pgtable_cache_init().
Link: http://lkml.kernel.org/r/1566457046-22637-1-git-send-email-rppt@linux.ibm.com
Signed-off-by: Mike Rapoport <rppt@linux.ibm.com>
Acked-by: Will Deacon <will@kernel.org> [arm64]
Acked-by: Thomas Gleixner <tglx@linutronix.de> [x86]
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Matthew Wilcox <willy@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Currently kmemleak uses a static early_log buffer to trace all memory
allocation/freeing before the slab allocator is initialised. Such early
log is replayed during kmemleak_init() to properly initialise the kmemleak
metadata for objects allocated up that point. With a memory pool that
does not rely on the slab allocator, it is possible to skip this early log
entirely.
In order to remove the early logging, consider kmemleak_enabled == 1 by
default while the kmem_cache availability is checked directly on the
object_cache and scan_area_cache variables. The RCU callback is only
invoked after object_cache has been initialised as we wouldn't have any
concurrent list traversal before this.
In order to reduce the number of callbacks before kmemleak is fully
initialised, move the kmemleak_init() call to mm_init().
[akpm@linux-foundation.org: coding-style fixes]
[akpm@linux-foundation.org: remove WARN_ON(), per Catalin]
Link: http://lkml.kernel.org/r/20190812160642.52134-4-catalin.marinas@arm.com
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: Michal Hocko <mhocko@kernel.org>
Cc: Qian Cai <cai@lca.pw>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Summary of modules changes for the 5.4 merge window:
- Introduce exported symbol namespaces.
This new feature allows subsystem maintainers to partition and
categorize their exported symbols into explicit namespaces. Module
authors are now required to import the namespaces they need.
Some of the main motivations of this feature include: allowing kernel
developers to better manage the export surface, allow subsystem
maintainers to explicitly state that usage of some exported symbols
should only be limited to certain users (think: inter-module or
inter-driver symbols, debugging symbols, etc), as well as more easily
limiting the availability of namespaced symbols to other parts of the
kernel. With the module import requirement, it is also easier to spot
the misuse of exported symbols during patch review. Two new macros are
introduced: EXPORT_SYMBOL_NS() and EXPORT_SYMBOL_NS_GPL(). The API is
thoroughly documented in Documentation/kbuild/namespaces.rst.
- Some small code and kbuild cleanups here and there.
-----BEGIN PGP SIGNATURE-----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=72Uy
-----END PGP SIGNATURE-----
Merge tag 'modules-for-v5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/jeyu/linux
Pull modules updates from Jessica Yu:
"The main bulk of this pull request introduces a new exported symbol
namespaces feature. The number of exported symbols is increasingly
growing with each release (we're at about 31k exports as of 5.3-rc7)
and we currently have no way of visualizing how these symbols are
"clustered" or making sense of this huge export surface.
Namespacing exported symbols allows kernel developers to more
explicitly partition and categorize exported symbols, as well as more
easily limiting the availability of namespaced symbols to other parts
of the kernel. For starters, we have introduced the USB_STORAGE
namespace to demonstrate the API's usage. I have briefly summarized
the feature and its main motivations in the tag below.
Summary:
- Introduce exported symbol namespaces.
This new feature allows subsystem maintainers to partition and
categorize their exported symbols into explicit namespaces. Module
authors are now required to import the namespaces they need.
Some of the main motivations of this feature include: allowing
kernel developers to better manage the export surface, allow
subsystem maintainers to explicitly state that usage of some
exported symbols should only be limited to certain users (think:
inter-module or inter-driver symbols, debugging symbols, etc), as
well as more easily limiting the availability of namespaced symbols
to other parts of the kernel.
With the module import requirement, it is also easier to spot the
misuse of exported symbols during patch review.
Two new macros are introduced: EXPORT_SYMBOL_NS() and
EXPORT_SYMBOL_NS_GPL(). The API is thoroughly documented in
Documentation/kbuild/namespaces.rst.
- Some small code and kbuild cleanups here and there"
* tag 'modules-for-v5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/jeyu/linux:
module: Remove leftover '#undef' from export header
module: remove unneeded casts in cmp_name()
module: move CONFIG_UNUSED_SYMBOLS to the sub-menu of MODULES
module: remove redundant 'depends on MODULES'
module: Fix link failure due to invalid relocation on namespace offset
usb-storage: export symbols in USB_STORAGE namespace
usb-storage: remove single-use define for debugging
docs: Add documentation for Symbol Namespaces
scripts: Coccinelle script for namespace dependencies.
modpost: add support for generating namespace dependencies
export: allow definition default namespaces in Makefiles or sources
module: add config option MODULE_ALLOW_MISSING_NAMESPACE_IMPORTS
modpost: add support for symbol namespaces
module: add support for symbol namespaces.
export: explicitly align struct kernel_symbol
module: support reading multiple values per modinfo tag
- virtio support
- Fixes for our new time travel mode
- Various improvements to make lockdep and kasan work better
- SPDX header updates
-----BEGIN PGP SIGNATURE-----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=oxpp
-----END PGP SIGNATURE-----
Merge tag 'for-linus-5.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rw/uml
Pull UML updates from Richard Weinberger:
- virtio support
- fixes for our new time travel mode
- various improvements to make lockdep and kasan work better
- SPDX header updates
* tag 'for-linus-5.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rw/uml: (25 commits)
um: irq: Fix LAST_IRQ usage in init_IRQ()
um: Add SPDX headers for files in arch/um/include
um: Add SPDX headers for files in arch/um/os-Linux
um: Add SPDX headers to files in arch/um/kernel/
um: Add SPDX headers for files in arch/um/drivers
um: virtio: Implement VHOST_USER_PROTOCOL_F_REPLY_ACK
um: virtio: Implement VHOST_USER_PROTOCOL_F_SLAVE_REQ
um: drivers: Add virtio vhost-user driver
um: Use real DMA barriers
um: Don't use generic barrier.h
um: time-travel: Restrict time update in IRQ handler
um: time-travel: Fix periodic timers
um: Enable CONFIG_CONSTRUCTORS
um: Place (soft)irq text with macros
um: Fix VDSO compiler warning
um: Implement TRACE_IRQFLAGS_SUPPORT
um: Remove misleading #define ARCh_IRQ_ENABLED
um: Avoid using uninitialized regs
um: Remove sig_info[SIGALRM]
um: Error handling fixes in vector drivers
...
gcc 9+ (and gcc 8.3, 7.5) provides a way to override the otherwise
crude heuristic that gcc uses to estimate the size of the code
represented by an asm() statement. From the gcc docs
If you use 'asm inline' instead of just 'asm', then for inlining
purposes the size of the asm is taken as the minimum size, ignoring
how many instructions GCC thinks it is.
For compatibility with older compilers, we obviously want a
#if [understands asm inline]
#define asm_inline asm inline
#else
#define asm_inline asm
#endif
But since we #define the identifier inline to attach some attributes,
we have to use an alternate spelling of that keyword. gcc provides
both __inline__ and __inline, and we currently #define both to inline,
so they all have the same semantics. We have to free up one of
__inline__ and __inline, and the latter is by far the easiest.
The two x86 changes cause smaller code gen differences than I'd
expect, but I think we do want the asm_inline thing available sooner
or later, so this is just to get the ball rolling.
-----BEGIN PGP SIGNATURE-----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=+BVw
-----END PGP SIGNATURE-----
Merge tag 'compiler-attributes-for-linus-v5.4' of git://github.com/ojeda/linux
Pull asm inline support from Miguel Ojeda:
"Make use of gcc 9's "asm inline()" (Rasmus Villemoes):
gcc 9+ (and gcc 8.3, 7.5) provides a way to override the otherwise
crude heuristic that gcc uses to estimate the size of the code
represented by an asm() statement. From the gcc docs
If you use 'asm inline' instead of just 'asm', then for inlining
purposes the size of the asm is taken as the minimum size, ignoring
how many instructions GCC thinks it is.
For compatibility with older compilers, we obviously want a
#if [understands asm inline]
#define asm_inline asm inline
#else
#define asm_inline asm
#endif
But since we #define the identifier inline to attach some attributes,
we have to use an alternate spelling of that keyword. gcc provides
both __inline__ and __inline, and we currently #define both to inline,
so they all have the same semantics.
We have to free up one of __inline__ and __inline, and the latter is
by far the easiest.
The two x86 changes cause smaller code gen differences than I'd
expect, but I think we do want the asm_inline thing available sooner
or later, so this is just to get the ball rolling"
* tag 'compiler-attributes-for-linus-v5.4' of git://github.com/ojeda/linux:
x86: bug.h: use asm_inline in _BUG_FLAGS definitions
x86: alternative.h: use asm_inline for all alternative variants
compiler-types.h: add asm_inline definition
compiler_types.h: don't #define __inline
lib/zstd/mem.h: replace __inline by inline
staging: rtl8723bs: replace __inline by inline
- add modpost warn exported symbols marked as 'static' because 'static'
and EXPORT_SYMBOL is an odd combination
- break the build early if gold linker is used
- optimize the Bison rule to produce .c and .h files by a single
pattern rule
- handle PREEMPT_RT in the module vermagic and UTS_VERSION
- warn CONFIG options leaked to the user-space except existing ones
- make single targets work properly
- rebuild modules when module linker scripts are updated
- split the module final link stage into scripts/Makefile.modfinal
- fix the missed error code in merge_config.sh
- improve the error message displayed on the attempt of the O= build
in unclean source tree
- remove 'clean-dirs' syntax
- disable -Wimplicit-fallthrough warning for Clang
- add CONFIG_CC_OPTIMIZE_FOR_SIZE_O3 for ARC
- remove ARCH_{CPP,A,C}FLAGS variables
- add $(BASH) to run bash scripts
- change *CFLAGS_<basetarget>.o to take the relative path to $(obj)
instead of the basename
- stop suppressing Clang's -Wunused-function warnings when W=1
- fix linux/export.h to avoid genksyms calculating CRC of trimmed
exported symbols
- misc cleanups
-----BEGIN PGP SIGNATURE-----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=VGqV
-----END PGP SIGNATURE-----
Merge tag 'kbuild-v5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild
Pull Kbuild updates from Masahiro Yamada:
- add modpost warn exported symbols marked as 'static' because 'static'
and EXPORT_SYMBOL is an odd combination
- break the build early if gold linker is used
- optimize the Bison rule to produce .c and .h files by a single
pattern rule
- handle PREEMPT_RT in the module vermagic and UTS_VERSION
- warn CONFIG options leaked to the user-space except existing ones
- make single targets work properly
- rebuild modules when module linker scripts are updated
- split the module final link stage into scripts/Makefile.modfinal
- fix the missed error code in merge_config.sh
- improve the error message displayed on the attempt of the O= build in
unclean source tree
- remove 'clean-dirs' syntax
- disable -Wimplicit-fallthrough warning for Clang
- add CONFIG_CC_OPTIMIZE_FOR_SIZE_O3 for ARC
- remove ARCH_{CPP,A,C}FLAGS variables
- add $(BASH) to run bash scripts
- change *CFLAGS_<basetarget>.o to take the relative path to $(obj)
instead of the basename
- stop suppressing Clang's -Wunused-function warnings when W=1
- fix linux/export.h to avoid genksyms calculating CRC of trimmed
exported symbols
- misc cleanups
* tag 'kbuild-v5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild: (63 commits)
genksyms: convert to SPDX License Identifier for lex.l and parse.y
modpost: use __section in the output to *.mod.c
modpost: use MODULE_INFO() for __module_depends
export.h, genksyms: do not make genksyms calculate CRC of trimmed symbols
export.h: remove defined(__KERNEL__), which is no longer needed
kbuild: allow Clang to find unused static inline functions for W=1 build
kbuild: rename KBUILD_ENABLE_EXTRA_GCC_CHECKS to KBUILD_EXTRA_WARN
kbuild: refactor scripts/Makefile.extrawarn
merge_config.sh: ignore unwanted grep errors
kbuild: change *FLAGS_<basetarget>.o to take the path relative to $(obj)
modpost: add NOFAIL to strndup
modpost: add guid_t type definition
kbuild: add $(BASH) to run scripts with bash-extension
kbuild: remove ARCH_{CPP,A,C}FLAGS
kbuild,arc: add CONFIG_CC_OPTIMIZE_FOR_PERFORMANCE_O3 for ARC
kbuild: Do not enable -Wimplicit-fallthrough for clang for now
kbuild: clean up subdir-ymn calculation in Makefile.clean
kbuild: remove unneeded '+' marker from cmd_clean
kbuild: remove clean-dirs syntax
kbuild: check clean srctree even earlier
...
Pull misc mount API conversions from Al Viro:
"Conversions to new API for shmem and friends and for mount_mtd()-using
filesystems.
As for the rest of the mount API conversions in -next, some of them
belong in the individual trees (e.g. binderfs one should definitely go
through android folks, after getting redone on top of their changes).
I'm going to drop those and send the rest (trivial ones + stuff ACKed
by maintainers) in a separate series - by that point they are
independent from each other.
Some stuff has already migrated into individual trees (NFS conversion,
for example, or FUSE stuff, etc.); those presumably will go through
the regular merges from corresponding trees."
* 'work.mount2' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
vfs: Make fs_parse() handle fs_param_is_fd-type params better
vfs: Convert ramfs, shmem, tmpfs, devtmpfs, rootfs to use the new mount API
shmem_parse_one(): switch to use of fs_parse()
shmem_parse_options(): take handling a single option into a helper
shmem_parse_options(): don't bother with mpol in separate variable
shmem_parse_options(): use a separate structure to keep the results
make shmem_fill_super() static
make ramfs_fill_super() static
devtmpfs: don't mix {ramfs,shmem}_fill_super() with mount_single()
vfs: Convert squashfs to use the new mount API
mtd: Kill mount_mtd()
vfs: Convert jffs2 to use the new mount API
vfs: Convert cramfs to use the new mount API
vfs: Convert romfs to use the new mount API
vfs: Add a single-or-reconfig keying to vfs_get_super()
Pull core timer updates from Thomas Gleixner:
"Timers and timekeeping updates:
- A large overhaul of the posix CPU timer code which is a preparation
for moving the CPU timer expiry out into task work so it can be
properly accounted on the task/process.
An update to the bogus permission checks will come later during the
merge window as feedback was not complete before heading of for
travel.
- Switch the timerqueue code to use cached rbtrees and get rid of the
homebrewn caching of the leftmost node.
- Consolidate hrtimer_init() + hrtimer_init_sleeper() calls into a
single function
- Implement the separation of hrtimers to be forced to expire in hard
interrupt context even when PREEMPT_RT is enabled and mark the
affected timers accordingly.
- Implement a mechanism for hrtimers and the timer wheel to protect
RT against priority inversion and live lock issues when a (hr)timer
which should be canceled is currently executing the callback.
Instead of infinitely spinning, the task which tries to cancel the
timer blocks on a per cpu base expiry lock which is held and
released by the (hr)timer expiry code.
- Enable the Hyper-V TSC page based sched_clock for Hyper-V guests
resulting in faster access to timekeeping functions.
- Updates to various clocksource/clockevent drivers and their device
tree bindings.
- The usual small improvements all over the place"
* 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (101 commits)
posix-cpu-timers: Fix permission check regression
posix-cpu-timers: Always clear head pointer on dequeue
hrtimer: Add a missing bracket and hide `migration_base' on !SMP
posix-cpu-timers: Make expiry_active check actually work correctly
posix-timers: Unbreak CONFIG_POSIX_TIMERS=n build
tick: Mark sched_timer to expire in hard interrupt context
hrtimer: Add kernel doc annotation for HRTIMER_MODE_HARD
x86/hyperv: Hide pv_ops access for CONFIG_PARAVIRT=n
posix-cpu-timers: Utilize timerqueue for storage
posix-cpu-timers: Move state tracking to struct posix_cputimers
posix-cpu-timers: Deduplicate rlimit handling
posix-cpu-timers: Remove pointless comparisons
posix-cpu-timers: Get rid of 64bit divisions
posix-cpu-timers: Consolidate timer expiry further
posix-cpu-timers: Get rid of zero checks
rlimit: Rewrite non-sensical RLIMIT_CPU comment
posix-cpu-timers: Respect INFINITY for hard RTTIME limit
posix-cpu-timers: Switch thread group sampling to array
posix-cpu-timers: Restructure expiry array
posix-cpu-timers: Remove cputime_expires
...
Pull scheduler updates from Ingo Molnar:
- MAINTAINERS: Add Mark Rutland as perf submaintainer, Juri Lelli and
Vincent Guittot as scheduler submaintainers. Add Dietmar Eggemann,
Steven Rostedt, Ben Segall and Mel Gorman as scheduler reviewers.
As perf and the scheduler is getting bigger and more complex,
document the status quo of current responsibilities and interests,
and spread the review pain^H^H^H^H fun via an increase in the Cc:
linecount generated by scripts/get_maintainer.pl. :-)
- Add another series of patches that brings the -rt (PREEMPT_RT) tree
closer to mainline: split the monolithic CONFIG_PREEMPT dependencies
into a new CONFIG_PREEMPTION category that will allow the eventual
introduction of CONFIG_PREEMPT_RT. Still a few more hundred patches
to go though.
- Extend the CPU cgroup controller with uclamp.min and uclamp.max to
allow the finer shaping of CPU bandwidth usage.
- Micro-optimize energy-aware wake-ups from O(CPUS^2) to O(CPUS).
- Improve the behavior of high CPU count, high thread count
applications running under cpu.cfs_quota_us constraints.
- Improve balancing with SCHED_IDLE (SCHED_BATCH) tasks present.
- Improve CPU isolation housekeeping CPU allocation NUMA locality.
- Fix deadline scheduler bandwidth calculations and logic when cpusets
rebuilds the topology, or when it gets deadline-throttled while it's
being offlined.
- Convert the cpuset_mutex to percpu_rwsem, to allow it to be used from
setscheduler() system calls without creating global serialization.
Add new synchronization between cpuset topology-changing events and
the deadline acceptance tests in setscheduler(), which were broken
before.
- Rework the active_mm state machine to be less confusing and more
optimal.
- Rework (simplify) the pick_next_task() slowpath.
- Improve load-balancing on AMD EPYC systems.
- ... and misc cleanups, smaller fixes and improvements - please see
the Git log for more details.
* 'sched-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (53 commits)
sched/psi: Correct overly pessimistic size calculation
sched/fair: Speed-up energy-aware wake-ups
sched/uclamp: Always use 'enum uclamp_id' for clamp_id values
sched/uclamp: Update CPU's refcount on TG's clamp changes
sched/uclamp: Use TG's clamps to restrict TASK's clamps
sched/uclamp: Propagate system defaults to the root group
sched/uclamp: Propagate parent clamps
sched/uclamp: Extend CPU's cgroup controller
sched/topology: Improve load balancing on AMD EPYC systems
arch, ia64: Make NUMA select SMP
sched, perf: MAINTAINERS update, add submaintainers and reviewers
sched/fair: Use rq_lock/unlock in online_fair_sched_group
cpufreq: schedutil: fix equation in comment
sched: Rework pick_next_task() slow-path
sched: Allow put_prev_task() to drop rq->lock
sched/fair: Expose newidle_balance()
sched: Add task_struct pointer to sched_class::set_curr_task
sched: Rework CPU hotplug task selection
sched/{rt,deadline}: Fix set_next_task vs pick_next_task
sched: Fix kerneldoc comment for ia64_set_curr_task
...
We do need to call the constructors for *modules*, and
at least for KASAN in the future, we must call even the
kernel constructors only later when the kernel has been
initialized.
Instead of relying on libc to call them, emit an empty
section for libc and let the kernel's CONSTRUCTORS code
do the rest of the job.
Tested that it indeed doesn't work in modules, and does
work after the fixes in both, with a few functions with
__attribute__((constructor)) in both dynamic and static
builds.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
This adds an asm_inline macro which expands to "asm inline" [1] when
the compiler supports it. This is currently gcc 9.1+, gcc 8.3
and (once released) gcc 7.5 [2]. It expands to just "asm" for other
compilers.
Using asm inline("foo") instead of asm("foo") overrules gcc's
heuristic estimate of the size of the code represented by the asm()
statement, and makes gcc use the minimum possible size instead. That
can in turn affect gcc's inlining decisions.
I wasn't sure whether to make this a function-like macro or not - this
way, it can be combined with volatile as
asm_inline volatile()
but perhaps we'd prefer to spell that
asm_inline_volatile()
anyway.
The Kconfig logic is taken from an RFC patch by Masahiro Yamada [3].
[1] Technically, asm __inline, since both inline and __inline__
are macros that attach various attributes, making gcc barf if one
literally does "asm inline()". However, the third spelling __inline is
available for referring to the bare keyword.
[2] https://lore.kernel.org/lkml/20190907001411.GG9749@gate.crashing.org/
[3] https://lore.kernel.org/lkml/1544695154-15250-1-git-send-email-yamada.masahiro@socionext.com/
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Miguel Ojeda <miguel.ojeda.sandonis@gmail.com>
Convert the ramfs, shmem, tmpfs, devtmpfs and rootfs filesystems to the new
internal mount API as the old one will be obsoleted and removed. This
allows greater flexibility in communication of mount parameters between
userspace, the VFS and the filesystem.
See Documentation/filesystems/mount_api.txt for more information.
Note that tmpfs is slightly tricky as it can contain embedded commas, so it
can't be trivially split up using strsep() to break on commas in
generic_parse_monolithic(). Instead, tmpfs has to supply its own generic
parser.
However, if tmpfs changes, then devtmpfs and rootfs, which are wrappers
around tmpfs or ramfs, must change too - and thus so must ramfs, so these
had to be converted also.
[AV: rewritten]
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Hugh Dickins <hughd@google.com>
cc: linux-mm@kvack.org
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
When CONFIG_MODULES is disabled, CONFIG_UNUSED_SYMBOLS is pointless,
thus it should be invisible.
Instead of adding "depends on MODULES", I moved it to the sub-menu
"Enable loadable module support", which is a better fit. I put it
close to TRIM_UNUSED_KSYMS because it depends on !UNUSED_SYMBOLS.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Jessica Yu <jeyu@kernel.org>
These are located in the 'if MODULES' ... 'endif' block.
Remove the redundant dependencies.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Jessica Yu <jeyu@kernel.org>
If MODULE_ALLOW_MISSING_NAMESPACE_IMPORTS is enabled (default=n), the
requirement for modules to import all namespaces that are used by
the module is relaxed.
Enabling this option effectively allows (invalid) modules to be loaded
while only a warning is emitted.
Disabling this option keeps the enforcement at module loading time and
loading is denied if the module's imports are not satisfactory.
Reviewed-by: Martijn Coenen <maco@android.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Matthias Maennich <maennich@google.com>
Signed-off-by: Jessica Yu <jeyu@kernel.org>
arch/arc/Makefile overrides -O2 with -O3. This is the only user of
ARCH_CFLAGS. There is no user of ARCH_CPPFLAGS or ARCH_AFLAGS.
My plan is to remove ARCH_{CPP,A,C}FLAGS after refactoring the ARC
Makefile.
Currently, ARC has no way to enable -Wmaybe-uninitialized because both
-O3 and -Os disable it. Enabling it will be useful for compile-testing.
This commit allows allmodconfig (, which defaults to -O2) to enable it.
Add CONFIG_CC_OPTIMIZE_FOR_PERFORMANCE_O3=y to all the defconfig files
in arch/arc/configs/ in order to keep the current config settings.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Vineet Gupta <vgupta@synopsys.com>
The cgroup CPU bandwidth controller allows to assign a specified
(maximum) bandwidth to the tasks of a group. However this bandwidth is
defined and enforced only on a temporal base, without considering the
actual frequency a CPU is running on. Thus, the amount of computation
completed by a task within an allocated bandwidth can be very different
depending on the actual frequency the CPU is running that task.
The amount of computation can be affected also by the specific CPU a
task is running on, especially when running on asymmetric capacity
systems like Arm's big.LITTLE.
With the availability of schedutil, the scheduler is now able
to drive frequency selections based on actual task utilization.
Moreover, the utilization clamping support provides a mechanism to
bias the frequency selection operated by schedutil depending on
constraints assigned to the tasks currently RUNNABLE on a CPU.
Giving the mechanisms described above, it is now possible to extend the
cpu controller to specify the minimum (or maximum) utilization which
should be considered for tasks RUNNABLE on a cpu.
This makes it possible to better defined the actual computational
power assigned to task groups, thus improving the cgroup CPU bandwidth
controller which is currently based just on time constraints.
Extend the CPU controller with a couple of new attributes uclamp.{min,max}
which allow to enforce utilization boosting and capping for all the
tasks in a group.
Specifically:
- uclamp.min: defines the minimum utilization which should be considered
i.e. the RUNNABLE tasks of this group will run at least at a
minimum frequency which corresponds to the uclamp.min
utilization
- uclamp.max: defines the maximum utilization which should be considered
i.e. the RUNNABLE tasks of this group will run up to a
maximum frequency which corresponds to the uclamp.max
utilization
These attributes:
a) are available only for non-root nodes, both on default and legacy
hierarchies, while system wide clamps are defined by a generic
interface which does not depends on cgroups. This system wide
interface enforces constraints on tasks in the root node.
b) enforce effective constraints at each level of the hierarchy which
are a restriction of the group requests considering its parent's
effective constraints. Root group effective constraints are defined
by the system wide interface.
This mechanism allows each (non-root) level of the hierarchy to:
- request whatever clamp values it would like to get
- effectively get only up to the maximum amount allowed by its parent
c) have higher priority than task-specific clamps, defined via
sched_setattr(), thus allowing to control and restrict task requests.
Add two new attributes to the cpu controller to collect "requested"
clamp values. Allow that at each non-root level of the hierarchy.
Keep it simple by not caring now about "effective" values computation
and propagation along the hierarchy.
Update sysctl_sched_uclamp_handler() to use the newly introduced
uclamp_mutex so that we serialize system default updates with cgroup
relate updates.
Signed-off-by: Patrick Bellasi <patrick.bellasi@arm.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Michal Koutny <mkoutny@suse.com>
Acked-by: Tejun Heo <tj@kernel.org>
Cc: Alessio Balsini <balsini@android.com>
Cc: Dietmar Eggemann <dietmar.eggemann@arm.com>
Cc: Joel Fernandes <joelaf@google.com>
Cc: Juri Lelli <juri.lelli@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Morten Rasmussen <morten.rasmussen@arm.com>
Cc: Paul Turner <pjt@google.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Quentin Perret <quentin.perret@arm.com>
Cc: Rafael J . Wysocki <rafael.j.wysocki@intel.com>
Cc: Steve Muckle <smuckle@google.com>
Cc: Suren Baghdasaryan <surenb@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Todd Kjos <tkjos@google.com>
Cc: Vincent Guittot <vincent.guittot@linaro.org>
Cc: Viresh Kumar <viresh.kumar@linaro.org>
Link: https://lkml.kernel.org/r/20190822132811.31294-2-patrick.bellasi@arm.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
CONFIG_CC_OPTIMIZE_FOR_SIZE was originally an independent boolean
option, but commit 877417e6ff ("Kbuild: change CC_OPTIMIZE_FOR_SIZE
definition") turned it into a choice between _PERFORMANCE and _SIZE.
The phrase "If unsure, say N." sounds like an independent option.
Reword the help text to make it appropriate for the choice menu.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Add CONFIG_ASM_MODVERSIONS. This allows to remove one if-conditional
nesting in scripts/Makefile.build.
scripts/Makefile.build is run every time Kbuild descends into a
sub-directory. So, I want to avoid $(wildcard ...) evaluation
where possible although computing $(wildcard ...) is so cheap that
it may not make measurable performance difference.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
This reverts commit 71c67a31f0.
Commit 117acf5c29 ("powerpc/Makefile: Always pass --synthetic to nm if
supported") removed the only conditional definition of $(NM), so we can
revert our temporary bodge to avoid Kconfig recursion and go back to
passing $(NM) through to the 'tools-support-relr.sh' when detecting
support for RELR relocations.
Signed-off-by: Will Deacon <will@kernel.org>
If the kernel is locked down, require that all modules have valid
signatures that we can verify.
I have adjusted the errors generated:
(1) If there's no signature (ENODATA) or we can't check it (ENOPKG,
ENOKEY), then:
(a) If signatures are enforced then EKEYREJECTED is returned.
(b) If there's no signature or we can't check it, but the kernel is
locked down then EPERM is returned (this is then consistent with
other lockdown cases).
(2) If the signature is unparseable (EBADMSG, EINVAL), the signature fails
the check (EKEYREJECTED) or a system error occurs (eg. ENOMEM), we
return the error we got.
Note that the X.509 code doesn't check for key expiry as the RTC might not
be valid or might not have been transferred to the kernel's clock yet.
[Modified by Matthew Garrett to remove the IMA integration. This will
be replaced with integration with the IMA architecture policy
patchset.]
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Matthew Garrett <matthewgarrett@google.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Cc: Jessica Yu <jeyu@kernel.org>
Signed-off-by: James Morris <jmorris@namei.org>
The lockdown module is intended to allow for kernels to be locked down
early in boot - sufficiently early that we don't have the ability to
kmalloc() yet. Add support for early initialisation of some LSMs, and
then add them to the list of names when we do full initialisation later.
Early LSMs are initialised in link order and cannot be overridden via
boot parameters, and cannot make use of kmalloc() (since the allocator
isn't initialised yet).
(Fixed by Stephen Rothwell to include a stub to fix builds when
!CONFIG_SECURITY)
Signed-off-by: Matthew Garrett <mjg59@google.com>
Acked-by: Kees Cook <keescook@chromium.org>
Acked-by: Casey Schaufler <casey@schaufler-ca.com>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: James Morris <jmorris@namei.org>
Update the build scripts and the version magic to reflect when
CONFIG_PREEMPT_RT is enabled in the same way as CONFIG_PREEMPT is treated.
The resulting version strings:
Linux m 5.3.0-rc1+ #100 SMP Fri Jul 26 ...
Linux m 5.3.0-rc1+ #101 SMP PREEMPT Fri Jul 26 ...
Linux m 5.3.0-rc1+ #102 SMP PREEMPT_RT Fri Jul 26 ...
The module vermagic:
5.3.0-rc1+ SMP mod_unload modversions
5.3.0-rc1+ SMP preempt mod_unload modversions
5.3.0-rc1+ SMP preempt_rt mod_unload modversions
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Commit 5cf896fb6b ("arm64: Add support for relocating the kernel with
RELR relocations") introduced CONFIG_TOOLS_SUPPORT_RELR, which checks
for RELR support in the toolchain as part of the kernel configuration.
During this procedure, "$(NM)" is invoked to see if it supports the new
relocation format, however PowerPC conditionally overrides this variable
in the architecture Makefile in order to pass '--synthetic' when
targetting PPC64.
This conditional override causes Kconfig to recurse forever, since
CONFIG_TOOLS_SUPPORT_RELR cannot be determined without $(NM) being
defined, but that in turn depends on CONFIG_PPC64:
$ make ARCH=powerpc CROSS_COMPILE=powerpc-linux-gnu-
scripts/kconfig/conf --syncconfig Kconfig
scripts/kconfig/conf --syncconfig Kconfig
scripts/kconfig/conf --syncconfig Kconfig
[...]
In this particular case, it looks like PowerPC may be able to pass
'--synthetic' unconditionally to nm or even drop it altogether. While
that is being resolved, let's just bodge the RELR check by picking up
$(NM) directly from the environment in whatever state it happens to be
in.
Cc: Peter Collingbourne <pcc@google.com>
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Suggested-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Will Deacon <will@kernel.org>
IMA will use the module_signature format for append signatures, so export
the relevant definitions and factor out the code which verifies that the
appended signature trailer is valid.
Also, create a CONFIG_MODULE_SIG_FORMAT option so that IMA can select it
and be able to use mod_check_sig() without having to depend on either
CONFIG_MODULE_SIG or CONFIG_MODULES.
s390 duplicated the definition of struct module_signature so now they can
use the new <linux/module_signature.h> header instead.
Signed-off-by: Thiago Jung Bauermann <bauerman@linux.ibm.com>
Acked-by: Jessica Yu <jeyu@kernel.org>
Reviewed-by: Philipp Rudo <prudo@linux.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Mimi Zohar <zohar@linux.ibm.com>
RELR is a relocation packing format for relative relocations.
The format is described in a generic-abi proposal:
https://groups.google.com/d/topic/generic-abi/bX460iggiKg/discussion
The LLD linker can be instructed to pack relocations in the RELR
format by passing the flag --pack-dyn-relocs=relr.
This patch adds a new config option, CONFIG_RELR. Enabling this option
instructs the linker to pack vmlinux's relative relocations in the RELR
format, and causes the kernel to apply the relocations at startup along
with the RELA relocations. RELA relocations still need to be applied
because the linker will emit RELA relative relocations if they are
unrepresentable in the RELR format (i.e. address not a multiple of 2).
Enabling CONFIG_RELR reduces the size of a defconfig kernel image
with CONFIG_RANDOMIZE_BASE by 3.5MB/16% uncompressed, or 550KB/5%
compressed (lz4).
Signed-off-by: Peter Collingbourne <pcc@google.com>
Tested-by: Nick Desaulniers <ndesaulniers@google.com>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Will Deacon <will@kernel.org>
CONFIG_PREEMPTION is selected by CONFIG_PREEMPT and by
CONFIG_PREEMPT_RT. Both PREEMPT and PREEMPT_RT require the same
functionality which today depends on CONFIG_PREEMPT.
Switch the preemption code, scheduler and init task over to use
CONFIG_PREEMPTION.
That's the first step towards RT in that area. The more complex changes are
coming separately.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Paul E. McKenney <paulmck@linux.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Link: http://lkml.kernel.org/r/20190726212124.117528401@linutronix.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Pull vfs mount updates from Al Viro:
"The first part of mount updates.
Convert filesystems to use the new mount API"
* 'work.mount0' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (63 commits)
mnt_init(): call shmem_init() unconditionally
constify ksys_mount() string arguments
don't bother with registering rootfs
init_rootfs(): don't bother with init_ramfs_fs()
vfs: Convert smackfs to use the new mount API
vfs: Convert selinuxfs to use the new mount API
vfs: Convert securityfs to use the new mount API
vfs: Convert apparmorfs to use the new mount API
vfs: Convert openpromfs to use the new mount API
vfs: Convert xenfs to use the new mount API
vfs: Convert gadgetfs to use the new mount API
vfs: Convert oprofilefs to use the new mount API
vfs: Convert ibmasmfs to use the new mount API
vfs: Convert qib_fs/ipathfs to use the new mount API
vfs: Convert efivarfs to use the new mount API
vfs: Convert configfs to use the new mount API
vfs: Convert binfmt_misc to use the new mount API
convenience helper: get_tree_single()
convenience helper get_tree_nodev()
vfs: Kill sget_userns()
...
Merge more updates from Andrew Morton:
"VM:
- z3fold fixes and enhancements by Henry Burns and Vitaly Wool
- more accurate reclaimed slab caches calculations by Yafang Shao
- fix MAP_UNINITIALIZED UAPI symbol to not depend on config, by
Christoph Hellwig
- !CONFIG_MMU fixes by Christoph Hellwig
- new novmcoredd parameter to omit device dumps from vmcore, by
Kairui Song
- new test_meminit module for testing heap and pagealloc
initialization, by Alexander Potapenko
- ioremap improvements for huge mappings, by Anshuman Khandual
- generalize kprobe page fault handling, by Anshuman Khandual
- device-dax hotplug fixes and improvements, by Pavel Tatashin
- enable synchronous DAX fault on powerpc, by Aneesh Kumar K.V
- add pte_devmap() support for arm64, by Robin Murphy
- unify locked_vm accounting with a helper, by Daniel Jordan
- several misc fixes
core/lib:
- new typeof_member() macro including some users, by Alexey Dobriyan
- make BIT() and GENMASK() available in asm, by Masahiro Yamada
- changed LIST_POISON2 on x86_64 to 0xdead000000000122 for better
code generation, by Alexey Dobriyan
- rbtree code size optimizations, by Michel Lespinasse
- convert struct pid count to refcount_t, by Joel Fernandes
get_maintainer.pl:
- add --no-moderated switch to skip moderated ML's, by Joe Perches
misc:
- ptrace PTRACE_GET_SYSCALL_INFO interface
- coda updates
- gdb scripts, various"
[ Using merge message suggestion from Vlastimil Babka, with some editing - Linus ]
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (100 commits)
fs/select.c: use struct_size() in kmalloc()
mm: add account_locked_vm utility function
arm64: mm: implement pte_devmap support
mm: introduce ARCH_HAS_PTE_DEVMAP
mm: clean up is_device_*_page() definitions
mm/mmap: move common defines to mman-common.h
mm: move MAP_SYNC to asm-generic/mman-common.h
device-dax: "Hotremove" persistent memory that is used like normal RAM
mm/hotplug: make remove_memory() interface usable
device-dax: fix memory and resource leak if hotplug fails
include/linux/lz4.h: fix spelling and copy-paste errors in documentation
ipc/mqueue.c: only perform resource calculation if user valid
include/asm-generic/bug.h: fix "cut here" for WARN_ON for __WARN_TAINT architectures
scripts/gdb: add helpers to find and list devices
scripts/gdb: add lx-genpd-summary command
drivers/pps/pps.c: clear offset flags in PPS_SETPARAMS ioctl
kernel/pid.c: convert struct pid count to refcount_t
drivers/rapidio/devices/rio_mport_cdev.c: NUL terminate some strings
select: shift restore_saved_sigmask_unless() into poll_select_copy_remaining()
select: change do_poll() to return -ERESTARTNOHAND rather than -EINTR
...
This fixes a couple typos I noticed in the slab Kconfig:
sacrifies -> sacrifices
accellerate -> accelerate
Seeing as no other instances of these typos are found elsewhere in the
kernel and that I originally added one of the two, I can only assume
working on slab must have caused damage to the spelling centers of my
brain.
Link: http://lkml.kernel.org/r/201905292203.CD000546EB@keescook
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Rename the accounting documentation files to ReST, add an
index for them and adjust in order to produce a nice html
output via the Sphinx build system.
At its new index.rst, let's add a :orphan: while this is not linked to
the main index.rst file, in order to avoid build warnings.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
- remove headers_{install,check}_all targets
- remove unreasonable 'depends on !UML' from CONFIG_SAMPLES
- re-implement 'make headers_install' more cleanly
- add new header-test-y syntax to compile-test headers
- compile-test exported headers to ensure they are compilable in
user-space
- compile-test headers under include/ to ensure they are self-contained
- remove -Waggregate-return, -Wno-uninitialized, -Wno-unused-value flags
- add -Werror=unknown-warning-option for Clang
- add 128-bit built-in types support to genksyms
- fix missed rebuild of modules.builtin
- propagate 'No space left on device' error in fixdep to Make
- allow Clang to use its integrated assembler
- improve some coccinelle scripts
- add a new flag KBUILD_ABS_SRCTREE to request Kbuild to use absolute
path for $(srctree).
- do not ignore errors when compression utility is missing
- misc cleanups
-----BEGIN PGP SIGNATURE-----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=E2Rz
-----END PGP SIGNATURE-----
Merge tag 'kbuild-v5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild
Pull Kbuild updates from Masahiro Yamada:
- remove headers_{install,check}_all targets
- remove unreasonable 'depends on !UML' from CONFIG_SAMPLES
- re-implement 'make headers_install' more cleanly
- add new header-test-y syntax to compile-test headers
- compile-test exported headers to ensure they are compilable in
user-space
- compile-test headers under include/ to ensure they are self-contained
- remove -Waggregate-return, -Wno-uninitialized, -Wno-unused-value
flags
- add -Werror=unknown-warning-option for Clang
- add 128-bit built-in types support to genksyms
- fix missed rebuild of modules.builtin
- propagate 'No space left on device' error in fixdep to Make
- allow Clang to use its integrated assembler
- improve some coccinelle scripts
- add a new flag KBUILD_ABS_SRCTREE to request Kbuild to use absolute
path for $(srctree).
- do not ignore errors when compression utility is missing
- misc cleanups
* tag 'kbuild-v5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild: (49 commits)
kbuild: use -- separater intead of $(filter-out ...) for cc-cross-prefix
kbuild: Inform user to pass ARCH= for make mrproper
kbuild: fix compression errors getting ignored
kbuild: add a flag to force absolute path for srctree
kbuild: replace KBUILD_SRCTREE with boolean building_out_of_srctree
kbuild: remove src and obj from the top Makefile
scripts/tags.sh: remove unused environment variables from comments
scripts/tags.sh: drop SUBARCH support for ARM
kbuild: compile-test kernel headers to ensure they are self-contained
kheaders: include only headers into kheaders_data.tar.xz
kheaders: remove meaningless -R option of 'ls'
kbuild: support header-test-pattern-y
kbuild: do not create wrappers for header-test-y
kbuild: compile-test exported headers to ensure they are self-contained
init/Kconfig: add CONFIG_CC_CAN_LINK
kallsyms: exclude kasan local symbols on s390
kbuild: add more hints about SUBDIRS replacement
coccinelle: api/stream_open: treat all wait_.*() calls as blocking
coccinelle: put_device: Add a cast to an expression for an assignment
coccinelle: put_device: Adjust a message construction
...
Print the currently enabled stack and heap initialization modes.
Stack initialization is enabled by a config flag, while heap
initialization is configured at boot time with defaults being set in the
config. It's more convenient for the user to have all information about
these hardening measures in one place at boot, so the user can reason
about the expected behavior of the running system.
The possible options for stack are:
- "all" for CONFIG_INIT_STACK_ALL;
- "byref_all" for CONFIG_GCC_PLUGIN_STRUCTLEAK_BYREF_ALL;
- "byref" for CONFIG_GCC_PLUGIN_STRUCTLEAK_BYREF;
- "__user" for CONFIG_GCC_PLUGIN_STRUCTLEAK_USER;
- "off" otherwise.
Depending on the values of init_on_alloc and init_on_free boottime options
we also report "heap alloc" and "heap free" as "on"/"off".
In the init_on_free mode initializing pages at boot time may take a while,
so print a notice about that as well. This depends on how much memory is
installed, the memory bandwidth, etc. On a relatively modern x86 system,
it takes about 0.75s/GB to wipe all memory:
[ 0.418722] mem auto-init: stack:byref_all, heap alloc:off, heap free:on
[ 0.419765] mem auto-init: clearing system memory may take some time...
[ 12.376605] Memory: 16408564K/16776672K available (14339K kernel code, 1397K rwdata, 3756K rodata, 1636K init, 11460K bss, 368108K reserved, 0K cma-reserved)
Link: http://lkml.kernel.org/r/20190617151050.92663-3-glider@google.com
Signed-off-by: Alexander Potapenko <glider@google.com>
Suggested-by: Kees Cook <keescook@chromium.org>
Acked-by: Kees Cook <keescook@chromium.org>
Cc: Christoph Lameter <cl@linux.com>
Cc: Dmitry Vyukov <dvyukov@google.com>
Cc: James Morris <jmorris@namei.org>
Cc: Jann Horn <jannh@google.com>
Cc: Kostya Serebryany <kcc@google.com>
Cc: Laura Abbott <labbott@redhat.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: Nick Desaulniers <ndesaulniers@google.com>
Cc: Randy Dunlap <rdunlap@infradead.org>
Cc: Sandeep Patil <sspatil@android.com>
Cc: "Serge E. Hallyn" <serge@hallyn.com>
Cc: Souptick Joarder <jrdr.linux@gmail.com>
Cc: Marco Elver <elver@google.com>
Cc: Kaiwan N Billimoria <kaiwan@kaiwantech.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- A fair pile of RST conversions, many from Mauro. These create more
than the usual number of simple but annoying merge conflicts with other
trees, unfortunately. He has a lot more of these waiting on the wings
that, I think, will go to you directly later on.
- A new document on how to use merges and rebases in kernel repos, and one
on Spectre vulnerabilities.
- Various improvements to the build system, including automatic markup of
function() references because some people, for reasons I will never
understand, were of the opinion that :c:func:``function()`` is
unattractive and not fun to type.
- We now recommend using sphinx 1.7, but still support back to 1.4.
- Lots of smaller improvements, warning fixes, typo fixes, etc.
-----BEGIN PGP SIGNATURE-----
iQFDBAABCAAtFiEEIw+MvkEiF49krdp9F0NaE2wMflgFAl0krAEPHGNvcmJldEBs
d24ubmV0AAoJEBdDWhNsDH5Yg98H/AuLqO9LpOgUjF4LhyjxGPdzJkY9RExSJ7km
gznyreLCZgFaJR+AY6YDsd4Jw6OJlPbu1YM/Qo3C3WrZVFVhgL/s2ebvBgCo50A8
raAFd8jTf4/mGCHnAqRotAPQ3mETJUk315B66lBJ6Oc+YdpRhwXWq8ZW2bJxInFF
3HDvoFgMf0KhLuMHUkkL0u3fxH1iA+KvDu8diPbJYFjOdOWENz/CV8wqdVkXRSEW
DJxIq89h/7d+hIG3d1I7Nw+gibGsAdjSjKv4eRKauZs4Aoxd1Gpl62z0JNk6aT3m
dtq4joLdwScydonXROD/Twn2jsu4xYTrPwVzChomElMowW/ZBBY=
=D0eO
-----END PGP SIGNATURE-----
Merge tag 'docs-5.3' of git://git.lwn.net/linux
Pull Documentation updates from Jonathan Corbet:
"It's been a relatively busy cycle for docs:
- A fair pile of RST conversions, many from Mauro. These create more
than the usual number of simple but annoying merge conflicts with
other trees, unfortunately. He has a lot more of these waiting on
the wings that, I think, will go to you directly later on.
- A new document on how to use merges and rebases in kernel repos,
and one on Spectre vulnerabilities.
- Various improvements to the build system, including automatic
markup of function() references because some people, for reasons I
will never understand, were of the opinion that
:c:func:``function()`` is unattractive and not fun to type.
- We now recommend using sphinx 1.7, but still support back to 1.4.
- Lots of smaller improvements, warning fixes, typo fixes, etc"
* tag 'docs-5.3' of git://git.lwn.net/linux: (129 commits)
docs: automarkup.py: ignore exceptions when seeking for xrefs
docs: Move binderfs to admin-guide
Disable Sphinx SmartyPants in HTML output
doc: RCU callback locks need only _bh, not necessarily _irq
docs: format kernel-parameters -- as code
Doc : doc-guide : Fix a typo
platform: x86: get rid of a non-existent document
Add the RCU docs to the core-api manual
Documentation: RCU: Add TOC tree hooks
Documentation: RCU: Rename txt files to rst
Documentation: RCU: Convert RCU UP systems to reST
Documentation: RCU: Convert RCU linked list to reST
Documentation: RCU: Convert RCU basic concepts to reST
docs: filesystems: Remove uneeded .rst extension on toctables
scripts/sphinx-pre-install: fix out-of-tree build
docs: zh_CN: submitting-drivers.rst: Remove a duplicated Documentation/
Documentation: PGP: update for newer HW devices
Documentation: Add section about CPU vulnerabilities for Spectre
Documentation: platform: Delete x86-laptop-drivers.txt
docs: Note that :c:func: should no longer be used
...
-----BEGIN PGP SIGNATURE-----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=VSYT
-----END PGP SIGNATURE-----
Merge tag 'for-5.3/block-20190708' of git://git.kernel.dk/linux-block
Pull block updates from Jens Axboe:
"This is the main block updates for 5.3. Nothing earth shattering or
major in here, just fixes, additions, and improvements all over the
map. This contains:
- Series of documentation fixes (Bart)
- Optimization of the blk-mq ctx get/put (Bart)
- null_blk removal race condition fix (Bob)
- req/bio_op() cleanups (Chaitanya)
- Series cleaning up the segment accounting, and request/bio mapping
(Christoph)
- Series cleaning up the page getting/putting for bios (Christoph)
- block cgroup cleanups and moving it to where it is used (Christoph)
- block cgroup fixes (Tejun)
- Series of fixes and improvements to bcache, most notably a write
deadlock fix (Coly)
- blk-iolatency STS_AGAIN and accounting fixes (Dennis)
- Series of improvements and fixes to BFQ (Douglas, Paolo)
- debugfs_create() return value check removal for drbd (Greg)
- Use struct_size(), where appropriate (Gustavo)
- Two lighnvm fixes (Heiner, Geert)
- MD fixes, including a read balance and corruption fix (Guoqing,
Marcos, Xiao, Yufen)
- block opal shadow mbr additions (Jonas, Revanth)
- sbitmap compare-and-exhange improvemnts (Pavel)
- Fix for potential bio->bi_size overflow (Ming)
- NVMe pull requests:
- improved PCIe suspent support (Keith Busch)
- error injection support for the admin queue (Akinobu Mita)
- Fibre Channel discovery improvements (James Smart)
- tracing improvements including nvmetc tracing support (Minwoo Im)
- misc fixes and cleanups (Anton Eidelman, Minwoo Im, Chaitanya
Kulkarni)"
- Various little fixes and improvements to drivers and core"
* tag 'for-5.3/block-20190708' of git://git.kernel.dk/linux-block: (153 commits)
blk-iolatency: fix STS_AGAIN handling
block: nr_phys_segments needs to be zero for REQ_OP_WRITE_ZEROES
blk-mq: simplify blk_mq_make_request()
blk-mq: remove blk_mq_put_ctx()
sbitmap: Replace cmpxchg with xchg
block: fix .bi_size overflow
block: sed-opal: check size of shadow mbr
block: sed-opal: ioctl for writing to shadow mbr
block: sed-opal: add ioctl for done-mark of shadow mbr
block: never take page references for ITER_BVEC
direct-io: use bio_release_pages in dio_bio_complete
block_dev: use bio_release_pages in bio_unmap_user
block_dev: use bio_release_pages in blkdev_bio_end_io
iomap: use bio_release_pages in iomap_dio_bio_end_io
block: use bio_release_pages in bio_map_user_iov
block: use bio_release_pages in bio_unmap_user
block: optionally mark pages dirty in bio_release_pages
block: move the BIO_NO_PAGE_REF check into bio_release_pages
block: skd_main.c: Remove call to memset after dma_alloc_coherent
block: mtip32xx: Remove call to memset after dma_alloc_coherent
...
The headers in include/ are globally used in the kernel source tree
to provide common APIs. They are included from external modules, too.
It will be useful to make as many headers self-contained as possible
so that we do not have to rely on a specific include order.
There are more than 4000 headers in include/. In my rough analysis,
70% of them are already self-contained. With efforts, most of them
can be self-contained.
For now, we must exclude more than 1000 headers just because they
cannot be compiled as standalone units. I added them to header-test-.
The blacklist was mostly generated by a script, so the reason of the
breakage should be checked later.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Tested-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Joel Fernandes (Google) <joel@joelfernandes.org>
Pull cgroup updates from Tejun Heo:
"Documentation updates and the addition of cgroup_parse_float() which
will be used by new controllers including blk-iocost"
* 'for-5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup:
docs: cgroup-v1: convert docs to ReST and rename to *.rst
cgroup: Move cgroup_parse_float() implementation out of CONFIG_SYSFS
cgroup: add cgroup_parse_float()
Pull scheduler updates from Ingo Molnar:
- Remove the unused per rq load array and all its infrastructure, by
Dietmar Eggemann.
- Add utilization clamping support by Patrick Bellasi. This is a
refinement of the energy aware scheduling framework with support for
boosting of interactive and capping of background workloads: to make
sure critical GUI threads get maximum frequency ASAP, and to make
sure background processing doesn't unnecessarily move to cpufreq
governor to higher frequencies and less energy efficient CPU modes.
- Add the bare minimum of tracepoints required for LISA EAS regression
testing, by Qais Yousef - which allows automated testing of various
power management features, including energy aware scheduling.
- Restructure the former tsk_nr_cpus_allowed() facility that the -rt
kernel used to modify the scheduler's CPU affinity logic such as
migrate_disable() - introduce the task->cpus_ptr value instead of
taking the address of &task->cpus_allowed directly - by Sebastian
Andrzej Siewior.
- Misc optimizations, fixes, cleanups and small enhancements - see the
Git log for details.
* 'sched-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (33 commits)
sched/uclamp: Add uclamp support to energy_compute()
sched/uclamp: Add uclamp_util_with()
sched/cpufreq, sched/uclamp: Add clamps for FAIR and RT tasks
sched/uclamp: Set default clamps for RT tasks
sched/uclamp: Reset uclamp values on RESET_ON_FORK
sched/uclamp: Extend sched_setattr() to support utilization clamping
sched/core: Allow sched_setattr() to use the current policy
sched/uclamp: Add system default clamps
sched/uclamp: Enforce last task's UCLAMP_MAX
sched/uclamp: Add bucket local max tracking
sched/uclamp: Add CPU's clamp buckets refcounting
sched/fair: Rename weighted_cpuload() to cpu_runnable_load()
sched/debug: Export the newly added tracepoints
sched/debug: Add sched_overutilized tracepoint
sched/debug: Add new tracepoint to track PELT at se level
sched/debug: Add new tracepoints to track PELT at rq level
sched/debug: Add a new sched_trace_*() helper functions
sched/autogroup: Make autogroup_path() always available
sched/wait: Deduplicate code with do-while
sched/topology: Remove unused 'sd' parameter from arch_scale_cpu_capacity()
...
Pull locking updates from Ingo Molnar:
"The main changes in this cycle are:
- rwsem scalability improvements, phase #2, by Waiman Long, which are
rather impressive:
"On a 2-socket 40-core 80-thread Skylake system with 40 reader
and writer locking threads, the min/mean/max locking operations
done in a 5-second testing window before the patchset were:
40 readers, Iterations Min/Mean/Max = 1,807/1,808/1,810
40 writers, Iterations Min/Mean/Max = 1,807/50,344/151,255
After the patchset, they became:
40 readers, Iterations Min/Mean/Max = 30,057/31,359/32,741
40 writers, Iterations Min/Mean/Max = 94,466/95,845/97,098"
There's a lot of changes to the locking implementation that makes
it similar to qrwlock, including owner handoff for more fair
locking.
Another microbenchmark shows how across the spectrum the
improvements are:
"With a locking microbenchmark running on 5.1 based kernel, the
total locking rates (in kops/s) on a 2-socket Skylake system
with equal numbers of readers and writers (mixed) before and
after this patchset were:
# of Threads Before Patch After Patch
------------ ------------ -----------
2 2,618 4,193
4 1,202 3,726
8 802 3,622
16 729 3,359
32 319 2,826
64 102 2,744"
The changes are extensive and the patch-set has been through
several iterations addressing various locking workloads. There
might be more regressions, but unless they are pathological I
believe we want to use this new implementation as the baseline
going forward.
- jump-label optimizations by Daniel Bristot de Oliveira: the primary
motivation was to remove IPI disturbance of isolated RT-workload
CPUs, which resulted in the implementation of batched jump-label
updates. Beyond the improvement of the real-time characteristics
kernel, in one test this patchset improved static key update
overhead from 57 msecs to just 1.4 msecs - which is a nice speedup
as well.
- atomic64_t cross-arch type cleanups by Mark Rutland: over the last
~10 years of atomic64_t existence the various types used by the
APIs only had to be self-consistent within each architecture -
which means they became wildly inconsistent across architectures.
Mark puts and end to this by reworking all the atomic64
implementations to use 's64' as the base type for atomic64_t, and
to ensure that this type is consistently used for parameters and
return values in the API, avoiding further problems in this area.
- A large set of small improvements to lockdep by Yuyang Du: type
cleanups, output cleanups, function return type and othr cleanups
all around the place.
- A set of percpu ops cleanups and fixes by Peter Zijlstra.
- Misc other changes - please see the Git log for more details"
* 'locking-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (82 commits)
locking/lockdep: increase size of counters for lockdep statistics
locking/atomics: Use sed(1) instead of non-standard head(1) option
locking/lockdep: Move mark_lock() inside CONFIG_TRACE_IRQFLAGS && CONFIG_PROVE_LOCKING
x86/jump_label: Make tp_vec_nr static
x86/percpu: Optimize raw_cpu_xchg()
x86/percpu, sched/fair: Avoid local_clock()
x86/percpu, x86/irq: Relax {set,get}_irq_regs()
x86/percpu: Relax smp_processor_id()
x86/percpu: Differentiate this_cpu_{}() and __this_cpu_{}()
locking/rwsem: Guard against making count negative
locking/rwsem: Adaptive disabling of reader optimistic spinning
locking/rwsem: Enable time-based spinning on reader-owned rwsem
locking/rwsem: Make rwsem->owner an atomic_long_t
locking/rwsem: Enable readers spinning on writer
locking/rwsem: Clarify usage of owner's nonspinaable bit
locking/rwsem: Wake up almost all readers in wait queue
locking/rwsem: More optimal RT task handling of null owner
locking/rwsem: Always release wait_lock before waking up tasks
locking/rwsem: Implement lock handoff to prevent lock starvation
locking/rwsem: Make rwsem_spin_on_owner() return owner state
...
Multiple people have suggested compile-testing UAPI headers to ensure
they can be really included from user-space. "make headers_check" is
obviously not enough to catch bugs, and we often leak unresolved
references to user-space.
Use the new header-test-y syntax to implement it. Please note exported
headers are compile-tested with a completely different set of compiler
flags. The header search path is set to $(objtree)/usr/include since
exported headers should not include unexported ones.
We use -std=gnu89 for the kernel space since the kernel code highly
depends on GNU extensions. On the other hand, UAPI headers should be
written in more standardized C, so they are compiled with -std=c90.
This will emit errors if C++ style comments, the keyword 'inline', etc.
are used. Please use C style comments (/* ... */), '__inline__', etc.
in UAPI headers.
There is additional compiler requirement to enable this test because
many of UAPI headers include <stdlib.h>, <sys/ioctl.h>, <sys/time.h>,
etc. directly or indirectly. You cannot use kernel.org pre-built
toolchains [1] since they lack <stdlib.h>.
I reused CONFIG_CC_CAN_LINK to check the system header availability.
The intention is slightly different, but a compiler that can link
userspace programs provide system headers.
For now, a lot of headers need to be excluded because they cannot
be compiled standalone, but this is a good start point.
[1] https://mirrors.edge.kernel.org/pub/tools/crosstool/index.html
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Currently, scripts/cc-can-link.sh is run just for BPFILTER_UMH, but
defining CC_CAN_LINK will be useful in other places.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
No point having two call sites (earlier in init_rootfs() from
mnt_init() in case we are going to use shmem-style rootfs,
later from do_basic_setup() unconditionally), along with the
logics in shmem_init() itself to make the second call a no-op...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
init_mount_tree() can get to rootfs_fs_type directly and that simplifies
a lot of things. We don't need to register it, we don't need to look
it up *and* we don't need to bother with preventing subsequent userland
mounts. That's the way we should've done that from the very beginning.
There is a user-visible change, namely the disappearance of "rootfs"
from /proc/filesystems. Note that it's been unmountable all along
and it didn't show up in /proc/mounts; however, it *is* a user-visible
change and theoretically some script might've been using its presence
in /proc/filesystems to tell 2.4.11+ from earlier kernels.
*IF* any complaints about behaviour change do show up, we could fake
it in /proc/filesystems. I very much doubt we'll have to, though.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
the only thing done by the latter is making ramfs visible
to mount(2); we don't need it there - rootfs is separate
and, in fact, made visible to mount(2) in the same init_rootfs().
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
With gcc-4.6.3:
WARNING: vmlinux.o(.text.unlikely+0x140): Section mismatch in reference from the function populate_initrd_image() to the variable .init.ramfs.info:__initramfs_size
The function populate_initrd_image() references
the variable __init __initramfs_size.
This is often because populate_initrd_image lacks a __init
annotation or the annotation of __initramfs_size is wrong.
WARNING: vmlinux.o(.text.unlikely+0x14c): Section mismatch in reference from the function populate_initrd_image() to the function .init.text:unpack_to_rootfs()
The function populate_initrd_image() references
the function __init unpack_to_rootfs().
This is often because populate_initrd_image lacks a __init
annotation or the annotation of unpack_to_rootfs is wrong.
WARNING: vmlinux.o(.text.unlikely+0x198): Section mismatch in reference from the function populate_initrd_image() to the function .init.text:xwrite()
The function populate_initrd_image() references
the function __init xwrite().
This is often because populate_initrd_image lacks a __init
annotation or the annotation of xwrite is wrong.
Indeed, if the compiler decides not to inline populate_initrd_image(), a
warning is generated.
Fix this by adding the missing __init annotations.
Link: http://lkml.kernel.org/r/20190617074340.12779-1-geert@linux-m68k.org
Fixes: 7c184ecd26 ("initramfs: factor out a helper to populate the initrd image")
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Utilization clamping allows to clamp the CPU's utilization within a
[util_min, util_max] range, depending on the set of RUNNABLE tasks on
that CPU. Each task references two "clamp buckets" defining its minimum
and maximum (util_{min,max}) utilization "clamp values". A CPU's clamp
bucket is active if there is at least one RUNNABLE tasks enqueued on
that CPU and refcounting that bucket.
When a task is {en,de}queued {on,from} a rq, the set of active clamp
buckets on that CPU can change. If the set of active clamp buckets
changes for a CPU a new "aggregated" clamp value is computed for that
CPU. This is because each clamp bucket enforces a different utilization
clamp value.
Clamp values are always MAX aggregated for both util_min and util_max.
This ensures that no task can affect the performance of other
co-scheduled tasks which are more boosted (i.e. with higher util_min
clamp) or less capped (i.e. with higher util_max clamp).
A task has:
task_struct::uclamp[clamp_id]::bucket_id
to track the "bucket index" of the CPU's clamp bucket it refcounts while
enqueued, for each clamp index (clamp_id).
A runqueue has:
rq::uclamp[clamp_id]::bucket[bucket_id].tasks
to track how many RUNNABLE tasks on that CPU refcount each
clamp bucket (bucket_id) of a clamp index (clamp_id).
It also has a:
rq::uclamp[clamp_id]::bucket[bucket_id].value
to track the clamp value of each clamp bucket (bucket_id) of a clamp
index (clamp_id).
The rq::uclamp::bucket[clamp_id][] array is scanned every time it's
needed to find a new MAX aggregated clamp value for a clamp_id. This
operation is required only when it's dequeued the last task of a clamp
bucket tracking the current MAX aggregated clamp value. In this case,
the CPU is either entering IDLE or going to schedule a less boosted or
more clamped task.
The expected number of different clamp values configured at build time
is small enough to fit the full unordered array into a single cache
line, for configurations of up to 7 buckets.
Add to struct rq the basic data structures required to refcount the
number of RUNNABLE tasks for each clamp bucket. Add also the max
aggregation required to update the rq's clamp value at each
enqueue/dequeue event.
Use a simple linear mapping of clamp values into clamp buckets.
Pre-compute and cache bucket_id to avoid integer divisions at
enqueue/dequeue time.
Signed-off-by: Patrick Bellasi <patrick.bellasi@arm.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Alessio Balsini <balsini@android.com>
Cc: Dietmar Eggemann <dietmar.eggemann@arm.com>
Cc: Joel Fernandes <joelaf@google.com>
Cc: Juri Lelli <juri.lelli@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Morten Rasmussen <morten.rasmussen@arm.com>
Cc: Paul Turner <pjt@google.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Quentin Perret <quentin.perret@arm.com>
Cc: Rafael J . Wysocki <rafael.j.wysocki@intel.com>
Cc: Steve Muckle <smuckle@google.com>
Cc: Suren Baghdasaryan <surenb@google.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Todd Kjos <tkjos@google.com>
Cc: Vincent Guittot <vincent.guittot@linaro.org>
Cc: Viresh Kumar <viresh.kumar@linaro.org>
Link: https://lkml.kernel.org/r/20190621084217.8167-2-patrick.bellasi@arm.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
This option is entirely bfq specific, give it an appropinquate name.
Also make it depend on CONFIG_BFQ_GROUP_IOSCHED in Kconfig, as all
the functionality already does so anyway.
Acked-by: Tejun Heo <tj@kernel.org>
Acked-by: Paolo Valente <paolo.valente@linaro.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Sometimes it's useful to be able to explicitly ensure certain headers
remain self-contained, i.e. that they are compilable as standalone
units, by including and/or forward declaring everything they depend on.
Add special target header-test-y where individual Makefiles can add
headers to be tested if CONFIG_HEADER_TEST is enabled. This will
generate a dummy C file per header that gets built as part of extra-y.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
In order to prepare to add them to the Kernel API book,
convert the files to ReST format.
The conversion is actually:
- add blank lines and identation in order to identify paragraphs;
- fix tables markups;
- add some lists markups;
- mark literal blocks;
- adjust title markups.
At its new index.rst, let's add a :orphan: while this is not linked to
the main index.rst file, in order to avoid build warnings.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Convert the cgroup-v1 files to ReST format, in order to
allow a later addition to the admin-guide.
The conversion is actually:
- add blank lines and identation in order to identify paragraphs;
- fix tables markups;
- add some lists markups;
- mark literal blocks;
- adjust title markups.
At its new index.rst, let's add a :orphan: while this is not linked to
the main index.rst file, in order to avoid build warnings.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Tejun Heo <tj@kernel.org>
Here are some small char and misc driver fixes for 5.2-rc4 to resolve a
number of reported issues.
The most "notable" one here is the kernel headers in proc^Wsysfs fixes.
Those changes move the header file info into sysfs and fixes the build
issues that you reported.
Other than that, a bunch of small habanalabs driver fixes, some fpga
driver fixes, and a few other tiny driver fixes.
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXPuEVg8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yma0QCfVPa7r1rHqljz1UgvjKJTzVg8g9wAn1W1mddx
MIlG+0+ZnBdaPzyzoY1O
=0LJD
-----END PGP SIGNATURE-----
Merge tag 'char-misc-5.2-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver fixes from Greg KH:
"Here are some small char and misc driver fixes for 5.2-rc4 to resolve
a number of reported issues.
The most "notable" one here is the kernel headers in proc^Wsysfs
fixes. Those changes move the header file info into sysfs and fixes
the build issues that you reported.
Other than that, a bunch of small habanalabs driver fixes, some fpga
driver fixes, and a few other tiny driver fixes.
All of these have been in linux-next for a while with no reported
issues"
* tag 'char-misc-5.2-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
habanalabs: Read upper bits of trace buffer from RWPHI
habanalabs: Fix virtual address access via debugfs for 2MB pages
fpga: zynqmp-fpga: Correctly handle error pointer
habanalabs: fix bug in checking huge page optimization
habanalabs: Avoid using a non-initialized MMU cache mutex
habanalabs: fix debugfs code
uapi/habanalabs: add opcode for enable/disable device debug mode
habanalabs: halt debug engines on user process close
test_firmware: Use correct snprintf() limit
genwqe: Prevent an integer overflow in the ioctl
parport: Fix mem leak in parport_register_dev_model
fpga: dfl: expand minor range when registering chrdev region
fpga: dfl: Add lockdep classes for pdata->lock
fpga: dfl: afu: Pass the correct device to dma_mapping_error()
fpga: stratix10-soc: fix use-after-free on s10_init()
w1: ds2408: Fix typo after 49695ac468 (reset on output_write retry with readback)
kheaders: Do not regenerate archive if config is not changed
kheaders: Move from proc to sysfs
lkdtm/bugs: Adjust recursion test to avoid elision
lkdtm/usercopy: Moves the KERNEL_DS test to non-canonical
Chain keys are computed using Jenkins hash function, which needs an initial
hash to start with. Dedicate a macro to make this clear and configurable. A
later patch changes this initial chain key.
Signed-off-by: Yuyang Du <duyuyang@gmail.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: bvanassche@acm.org
Cc: frederic@kernel.org
Cc: ming.lei@redhat.com
Cc: will.deacon@arm.com
Link: https://lkml.kernel.org/r/20190506081939.74287-9-duyuyang@gmail.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Despite that there is a lockdep_init_task() which does nothing, lockdep
initiates tasks by assigning lockdep fields and does so inconsistently. Fix
this by using lockdep_init_task().
Signed-off-by: Yuyang Du <duyuyang@gmail.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: bvanassche@acm.org
Cc: frederic@kernel.org
Cc: ming.lei@redhat.com
Cc: will.deacon@arm.com
Link: https://lkml.kernel.org/r/20190506081939.74287-8-duyuyang@gmail.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
In commit:
4b53a3412d ("sched/core: Remove the tsk_nr_cpus_allowed() wrapper")
the tsk_nr_cpus_allowed() wrapper was removed. There was not
much difference in !RT but in RT we used this to implement
migrate_disable(). Within a migrate_disable() section the CPU mask is
restricted to single CPU while the "normal" CPU mask remains untouched.
As an alternative implementation Ingo suggested to use:
struct task_struct {
const cpumask_t *cpus_ptr;
cpumask_t cpus_mask;
};
with
t->cpus_ptr = &t->cpus_mask;
In -RT we then can switch the cpus_ptr to:
t->cpus_ptr = &cpumask_of(task_cpu(p));
in a migration disabled region. The rules are simple:
- Code that 'uses' ->cpus_allowed would use the pointer.
- Code that 'modifies' ->cpus_allowed would use the direct mask.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: https://lkml.kernel.org/r/20190423142636.14347-1-bigeasy@linutronix.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation version 2 of the license this program
is distributed in the hope that it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details you should have received a copy of the gnu general
public license along with this program if not write to the free
software foundation inc 59 temple place suite 330 boston ma 02111
1307 usa
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 83 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070034.021731668@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The kheaders archive consisting of the kernel headers used for compiling
bpf programs is in /proc. However there is concern that moving it here
will make it permanent. Let us move it to /sys/kernel as discussed [1].
[1] https://lore.kernel.org/patchwork/patch/1067310/#1265969
Suggested-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Joel Fernandes (Google) <joel@joelfernandes.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add SPDX license identifiers to all Make/Kconfig files which:
- Have no license information of any form
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add SPDX license identifiers to all files which:
- Have no license information of any form
- Have EXPORT_.*_SYMBOL_GPL inside which was used in the
initial scan/conversion to ignore the file
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commit 54c7a8916a ("initramfs: free initrd memory if opening
/initrd.image fails"), the kernel has unconditionally attempted to free
the initrd even if it doesn't exist.
In the non-existent case this causes a boot-time splat if
CONFIG_DEBUG_VIRTUAL is enabled due to a call to virt_to_phys() with a
NULL address.
Instead we should check that the initrd actually exists and only attempt
to free it if it does.
Link: http://lkml.kernel.org/r/20190516143125.48948-1-steven.price@arm.com
Fixes: 54c7a8916a ("initramfs: free initrd memory if opening /initrd.image fails")
Signed-off-by: Steven Price <steven.price@arm.com>
Reported-by: Mark Rutland <mark.rutland@arm.com>
Tested-by: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: Mike Rapoport <rppt@linux.ibm.com>
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Patch series "mm: Randomize free memory", v10.
This patch (of 3):
Randomization of the page allocator improves the average utilization of
a direct-mapped memory-side-cache. Memory side caching is a platform
capability that Linux has been previously exposed to in HPC
(high-performance computing) environments on specialty platforms. In
that instance it was a smaller pool of high-bandwidth-memory relative to
higher-capacity / lower-bandwidth DRAM. Now, this capability is going
to be found on general purpose server platforms where DRAM is a cache in
front of higher latency persistent memory [1].
Robert offered an explanation of the state of the art of Linux
interactions with memory-side-caches [2], and I copy it here:
It's been a problem in the HPC space:
http://www.nersc.gov/research-and-development/knl-cache-mode-performance-coe/
A kernel module called zonesort is available to try to help:
https://software.intel.com/en-us/articles/xeon-phi-software
and this abandoned patch series proposed that for the kernel:
https://lkml.kernel.org/r/20170823100205.17311-1-lukasz.daniluk@intel.com
Dan's patch series doesn't attempt to ensure buffers won't conflict, but
also reduces the chance that the buffers will. This will make performance
more consistent, albeit slower than "optimal" (which is near impossible
to attain in a general-purpose kernel). That's better than forcing
users to deploy remedies like:
"To eliminate this gradual degradation, we have added a Stream
measurement to the Node Health Check that follows each job;
nodes are rebooted whenever their measured memory bandwidth
falls below 300 GB/s."
A replacement for zonesort was merged upstream in commit cc9aec03e5
("x86/numa_emulation: Introduce uniform split capability"). With this
numa_emulation capability, memory can be split into cache sized
("near-memory" sized) numa nodes. A bind operation to such a node, and
disabling workloads on other nodes, enables full cache performance.
However, once the workload exceeds the cache size then cache conflicts
are unavoidable. While HPC environments might be able to tolerate
time-scheduling of cache sized workloads, for general purpose server
platforms, the oversubscribed cache case will be the common case.
The worst case scenario is that a server system owner benchmarks a
workload at boot with an un-contended cache only to see that performance
degrade over time, even below the average cache performance due to
excessive conflicts. Randomization clips the peaks and fills in the
valleys of cache utilization to yield steady average performance.
Here are some performance impact details of the patches:
1/ An Intel internal synthetic memory bandwidth measurement tool, saw a
3X speedup in a contrived case that tries to force cache conflicts.
The contrived cased used the numa_emulation capability to force an
instance of the benchmark to be run in two of the near-memory sized
numa nodes. If both instances were placed on the same emulated they
would fit and cause zero conflicts. While on separate emulated nodes
without randomization they underutilized the cache and conflicted
unnecessarily due to the in-order allocation per node.
2/ A well known Java server application benchmark was run with a heap
size that exceeded cache size by 3X. The cache conflict rate was 8%
for the first run and degraded to 21% after page allocator aging. With
randomization enabled the rate levelled out at 11%.
3/ A MongoDB workload did not observe measurable difference in
cache-conflict rates, but the overall throughput dropped by 7% with
randomization in one case.
4/ Mel Gorman ran his suite of performance workloads with randomization
enabled on platforms without a memory-side-cache and saw a mix of some
improvements and some losses [3].
While there is potentially significant improvement for applications that
depend on low latency access across a wide working-set, the performance
may be negligible to negative for other workloads. For this reason the
shuffle capability defaults to off unless a direct-mapped
memory-side-cache is detected. Even then, the page_alloc.shuffle=0
parameter can be specified to disable the randomization on those systems.
Outside of memory-side-cache utilization concerns there is potentially
security benefit from randomization. Some data exfiltration and
return-oriented-programming attacks rely on the ability to infer the
location of sensitive data objects. The kernel page allocator, especially
early in system boot, has predictable first-in-first out behavior for
physical pages. Pages are freed in physical address order when first
onlined.
Quoting Kees:
"While we already have a base-address randomization
(CONFIG_RANDOMIZE_MEMORY), attacks against the same hardware and
memory layouts would certainly be using the predictability of
allocation ordering (i.e. for attacks where the base address isn't
important: only the relative positions between allocated memory).
This is common in lots of heap-style attacks. They try to gain
control over ordering by spraying allocations, etc.
I'd really like to see this because it gives us something similar
to CONFIG_SLAB_FREELIST_RANDOM but for the page allocator."
While SLAB_FREELIST_RANDOM reduces the predictability of some local slab
caches it leaves vast bulk of memory to be predictably in order allocated.
However, it should be noted, the concrete security benefits are hard to
quantify, and no known CVE is mitigated by this randomization.
Introduce shuffle_free_memory(), and its helper shuffle_zone(), to perform
a Fisher-Yates shuffle of the page allocator 'free_area' lists when they
are initially populated with free memory at boot and at hotplug time. Do
this based on either the presence of a page_alloc.shuffle=Y command line
parameter, or autodetection of a memory-side-cache (to be added in a
follow-on patch).
The shuffling is done in terms of CONFIG_SHUFFLE_PAGE_ORDER sized free
pages where the default CONFIG_SHUFFLE_PAGE_ORDER is MAX_ORDER-1 i.e. 10,
4MB this trades off randomization granularity for time spent shuffling.
MAX_ORDER-1 was chosen to be minimally invasive to the page allocator
while still showing memory-side cache behavior improvements, and the
expectation that the security implications of finer granularity
randomization is mitigated by CONFIG_SLAB_FREELIST_RANDOM. The
performance impact of the shuffling appears to be in the noise compared to
other memory initialization work.
This initial randomization can be undone over time so a follow-on patch is
introduced to inject entropy on page free decisions. It is reasonable to
ask if the page free entropy is sufficient, but it is not enough due to
the in-order initial freeing of pages. At the start of that process
putting page1 in front or behind page0 still keeps them close together,
page2 is still near page1 and has a high chance of being adjacent. As
more pages are added ordering diversity improves, but there is still high
page locality for the low address pages and this leads to no significant
impact to the cache conflict rate.
[1]: https://itpeernetwork.intel.com/intel-optane-dc-persistent-memory-operating-modes/
[2]: https://lkml.kernel.org/r/AT5PR8401MB1169D656C8B5E121752FC0F8AB120@AT5PR8401MB1169.NAMPRD84.PROD.OUTLOOK.COM
[3]: https://lkml.org/lkml/2018/10/12/309
[dan.j.williams@intel.com: fix shuffle enable]
Link: http://lkml.kernel.org/r/154943713038.3858443.4125180191382062871.stgit@dwillia2-desk3.amr.corp.intel.com
[cai@lca.pw: fix SHUFFLE_PAGE_ALLOCATOR help texts]
Link: http://lkml.kernel.org/r/20190425201300.75650-1-cai@lca.pw
Link: http://lkml.kernel.org/r/154899811738.3165233.12325692939590944259.stgit@dwillia2-desk3.amr.corp.intel.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Qian Cai <cai@lca.pw>
Reviewed-by: Kees Cook <keescook@chromium.org>
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Keith Busch <keith.busch@intel.com>
Cc: Robert Elliott <elliott@hpe.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Various architectures including x86 poison the freed init memory. Do the
same in the generic free_initmem implementation and switch sparc32
architecture that is identical to the generic code over to it now.
Link: http://lkml.kernel.org/r/1550515285-17446-4-git-send-email-rppt@linux.ibm.com
Signed-off-by: Mike Rapoport <rppt@linux.ibm.com>
Reviewed-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Palmer Dabbelt <palmer@sifive.com>
Cc: Richard Kuo <rkuo@codeaurora.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Patch series "provide a generic free_initmem implementation", v2.
Many architectures implement free_initmem() in exactly the same or very
similar way: they wrap the call to free_initmem_default() with sometimes
different 'poison' parameter.
These patches switch those architectures to use a generic implementation
that does free_initmem_default(POISON_FREE_INITMEM).
This was inspired by Christoph's patches for free_initrd_mem [1] and I
shamelessly copied changelog entries from his patches :)
[1] https://lore.kernel.org/lkml/20190213174621.29297-1-hch@lst.de/
This patch (of 2):
For most architectures free_initmem just a wrapper for the same
free_initmem_default(-1) call. Provide that as a generic implementation
marked __weak.
Link: http://lkml.kernel.org/r/1550515285-17446-2-git-send-email-rppt@linux.ibm.com
Signed-off-by: Mike Rapoport <rppt@linux.ibm.com>
Reviewed-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Palmer Dabbelt <palmer@sifive.com>
Cc: Richard Kuo <rkuo@codeaurora.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Various architectures including x86 poison the freed initrd memory. Do
the same in the generic free_initrd_mem implementation and switch a few
more architectures that are identical to the generic code over to it now.
Link: http://lkml.kernel.org/r/20190213174621.29297-9-hch@lst.de
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Mike Rapoport <rppt@linux.ibm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com> [arm64]
Cc: Geert Uytterhoeven <geert@linux-m68k.org> [m68k]
Cc: Steven Price <steven.price@arm.com>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: Guan Xuetao <gxt@pku.edu.cn>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
For most architectures free_initrd_mem just expands to the same
free_reserved_area call. Provide that as a generic implementation marked
__weak.
Link: http://lkml.kernel.org/r/20190213174621.29297-8-hch@lst.de
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org> [m68k]
Acked-by: Mike Rapoport <rppt@linux.ibm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com> [arm64]
Cc: Steven Price <steven.price@arm.com>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: Guan Xuetao <gxt@pku.edu.cn>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
No need to handle the freeing disable in arch code when we already have a
core hook (and a different name for the option) for it.
Link: http://lkml.kernel.org/r/20190213174621.29297-7-hch@lst.de
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Catalin Marinas <catalin.marinas@arm.com> [arm64]
Acked-by: Mike Rapoport <rppt@linux.ibm.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org> [m68k]
Cc: Steven Price <steven.price@arm.com>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: Guan Xuetao <gxt@pku.edu.cn>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The code for kernels that support ramdisks or not is mostly the same.
Unify it by using an IS_ENABLED for the info message, and moving the error
message into a stub for populate_initrd_image.
[cai@lca.pw: fix a compilation error]
Link: http://lkml.kernel.org/r/20190328014806.36375-1-cai@lca.pw
Link: http://lkml.kernel.org/r/20190213174621.29297-6-hch@lst.de
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Qian Cai <cai@lca.pw>
Acked-by: Mike Rapoport <rppt@linux.ibm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com> [arm64]
Cc: Geert Uytterhoeven <geert@linux-m68k.org> [m68k]
Cc: Steven Price <steven.price@arm.com>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: Guan Xuetao <gxt@pku.edu.cn>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This will allow for cleaner code sharing in the caller.
Link: http://lkml.kernel.org/r/20190213174621.29297-5-hch@lst.de
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Mike Rapoport <rppt@linux.ibm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com> [arm64]
Cc: Geert Uytterhoeven <geert@linux-m68k.org> [m68k]
Cc: Steven Price <steven.price@arm.com>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: Guan Xuetao <gxt@pku.edu.cn>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Factor the kexec logic into a separate helper, and then inline the rest of
free_initrd into the only caller.
Link: http://lkml.kernel.org/r/20190213174621.29297-4-hch@lst.de
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Mike Rapoport <rppt@linux.ibm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com> [arm64]
Cc: Geert Uytterhoeven <geert@linux-m68k.org> [m68k]
Cc: Steven Price <steven.price@arm.com>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: Guan Xuetao <gxt@pku.edu.cn>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Patch series "initramfs tidyups".
I've spent some time chasing down behavior in initramfs and found
plenty of opportunity to improve the code. A first stab on that is
contained in this series.
This patch (of 7):
We free the initrd memory for all successful or error cases except for the
case where opening /initrd.image fails, which looks like an oversight.
Steven said:
: This also changes the behaviour when CONFIG_INITRAMFS_FORCE is enabled
: - specifically it means that the initrd is freed (previously it was
: ignored and never freed). But that seems like reasonable behaviour and
: the previous behaviour looks like another oversight.
Link: http://lkml.kernel.org/r/20190213174621.29297-3-hch@lst.de
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Steven Price <steven.price@arm.com>
Acked-by: Mike Rapoport <rppt@linux.ibm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com> [arm64]
Cc: Geert Uytterhoeven <geert@linux-m68k.org> [m68k]
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Guan Xuetao <gxt@pku.edu.cn>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
trust the CPU's RNG on NUMA systems; other miscellaneous cleanups and
fixes.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEK2m5VNv+CHkogTfJ8vlZVpUNgaMFAlzSEyoACgkQ8vlZVpUN
gaPJKAf/cBOEU9Zn0PzdCiybl6IT88A/EcL2FPPFbMrRI/aUDZ6jBURsa2Ds0+Rb
XiMjElnxMGSv03P+MTo0SPTVwYLGPpvNgplL25I4HMfKUPbpAdxk5UZS9pUllv2T
3ftQfGgdDalewlT8BH0K5EY9E8Whe9ODrLgGq6jXgXHm2sssDzPF+pB2ySuDRvsA
W/6rF+PW4n/2n3An6h9jc/0cShurarpHjvWzuFWY3Mevgrl53r8SppIt085/5K6A
tsSdXIqIBvhCp9OvXBHzEDCEPpdVBlL81XauIu6uMSlJ/oofOqjJs2Ib1k04Xx9z
dp4/7REfm/HFMyT9MNAYPmhmXruiiQ==
=56QI
-----END PGP SIGNATURE-----
Merge tag 'random_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/random
Pull randomness updates from Ted Ts'o:
- initialize the random driver earler
- fix CRNG initialization when we trust the CPU's RNG on NUMA systems
- other miscellaneous cleanups and fixes.
* tag 'random_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/random:
random: add a spinlock_t to struct batched_entropy
random: document get_random_int() family
random: fix CRNG initialization when random.trust_cpu=1
random: move rand_initialize() earlier
random: only read from /dev/random after its pool has received 128 bits
drivers/char/random.c: make primary_crng static
drivers/char/random.c: remove unused stuct poolinfo::poolbits
drivers/char/random.c: constify poolinfo_table
Here is the "big" set of driver core patches for 5.2-rc1
There are a number of ACPI patches in here as well, as Rafael said they
should go through this tree due to the driver core changes they
required. They have all been acked by the ACPI developers.
There are also a number of small subsystem-specific changes in here, due
to some changes to the kobject core code. Those too have all been acked
by the various subsystem maintainers.
As for content, it's pretty boring outside of the ACPI changes:
- spdx cleanups
- kobject documentation updates
- default attribute groups for kobjects
- other minor kobject/driver core fixes
All have been in linux-next for a while with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXNHDbw8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynDAgCfbb4LBR6I50wFXb8JM/R6cAS7qrsAn1unshKV
8XCYcif2RxjtdJWXbjdm
=/rLh
-----END PGP SIGNATURE-----
Merge tag 'driver-core-5.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core/kobject updates from Greg KH:
"Here is the "big" set of driver core patches for 5.2-rc1
There are a number of ACPI patches in here as well, as Rafael said
they should go through this tree due to the driver core changes they
required. They have all been acked by the ACPI developers.
There are also a number of small subsystem-specific changes in here,
due to some changes to the kobject core code. Those too have all been
acked by the various subsystem maintainers.
As for content, it's pretty boring outside of the ACPI changes:
- spdx cleanups
- kobject documentation updates
- default attribute groups for kobjects
- other minor kobject/driver core fixes
All have been in linux-next for a while with no reported issues"
* tag 'driver-core-5.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (47 commits)
kobject: clean up the kobject add documentation a bit more
kobject: Fix kernel-doc comment first line
kobject: Remove docstring reference to kset
firmware_loader: Fix a typo ("syfs" -> "sysfs")
kobject: fix dereference before null check on kobj
Revert "driver core: platform: Fix the usage of platform device name(pdev->name)"
init/config: Do not select BUILD_BIN2C for IKCONFIG
Provide in-kernel headers to make extending kernel easier
kobject: Improve doc clarity kobject_init_and_add()
kobject: Improve docs for kobject_add/del
driver core: platform: Fix the usage of platform device name(pdev->name)
livepatch: Replace klp_ktype_patch's default_attrs with groups
cpufreq: schedutil: Replace default_attrs field with groups
padata: Replace padata_attr_type default_attrs field with groups
irqdesc: Replace irq_kobj_type's default_attrs field with groups
net-sysfs: Replace ktype default_attrs field with groups
block: Replace all ktype default_attrs with groups
samples/kobject: Replace foo_ktype's default_attrs field with groups
kobject: Add support for default attribute groups to kobj_type
driver core: Postpone DMA tear-down until after devres release for probe failure
...
-----BEGIN PGP SIGNATURE-----
iQIzBAABCgAdFiEE7btrcuORLb1XUhEwjrBW1T7ssS0FAlzReuoACgkQjrBW1T7s
sS1uvBAA16pgnhRNxNTrp3LYft6lUWmF4n0baOTVtQNLhPjpwaOxHIrCBugkQCJB
QcQ9IQSOvIkaEW0XAQoPBaeLviiKhHOFw1Fv89OtW6xUidSfSV15lcI9f1F2pCm2
4yCL/8XvL6M0NhxiwftJAkWOXeDNLfjFnLwyLxBfgg3EeyqMgUB8raeosEID0ORR
gm2/g8DYS2r+KNqM/F4xvMSgabfi2bGk+8BtAaVnftJfstpRNrqKwWnSK3Wspj1l
5gkb8gSsiY6ns3V6RgNHrFlhevFg8V+VjcJt7FR+aUEjOkcoiXas/PhvamMzdsn/
FM1F/A0pM8FSybIUClhnnnxNPc+p8ZN/71YQAPs+Mnh3xvbtKea2lkhC+Xv4OpK3
edutSZWFaiIery82Rk00H3vqiSF1+kRIXSpZSS4mElk4FsVljkyH+nSP7rbmE2MR
EQe+kKnZl8QzWrVbnODC+EVvvVpA2bXDvENJmvKqus+t2G0OdV7Iku3F5E3KjF8k
S5RRV1zuBF3ugqnjmYrVmJtpEA8mxClmqvg6okru+qW6ngO5oOgVpPLjWn1CXcdj
wcuQ6Pe1QwAHS54e9WSWgCHVssLvm9nCdCqypdNaoyGWmbTWntwlrY7Y0JUQnAbB
6/G/DQQiCWY9y8bMZlTEydhIpgcsdROuPYv+oHF5+eQQthsWwHc=
=LH11
-----END PGP SIGNATURE-----
Merge tag 'pidfd-v5.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/brauner/linux
Pull pidfd updates from Christian Brauner:
"This patchset makes it possible to retrieve pidfds at process creation
time by introducing the new flag CLONE_PIDFD to the clone() system
call. Linus originally suggested to implement this as a new flag to
clone() instead of making it a separate system call.
After a thorough review from Oleg CLONE_PIDFD returns pidfds in the
parent_tidptr argument. This means we can give back the associated pid
and the pidfd at the same time. Access to process metadata information
thus becomes rather trivial.
As has been agreed, CLONE_PIDFD creates file descriptors based on
anonymous inodes similar to the new mount api. They are made
unconditional by this patchset as they are now needed by core kernel
code (vfs, pidfd) even more than they already were before (timerfd,
signalfd, io_uring, epoll etc.). The core patchset is rather small.
The bulky looking changelist is caused by David's very simple changes
to Kconfig to make anon inodes unconditional.
A pidfd comes with additional information in fdinfo if the kernel
supports procfs. The fdinfo file contains the pid of the process in
the callers pid namespace in the same format as the procfs status
file, i.e. "Pid:\t%d".
To remove worries about missing metadata access this patchset comes
with a sample/test program that illustrates how a combination of
CLONE_PIDFD and pidfd_send_signal() can be used to gain race-free
access to process metadata through /proc/<pid>.
Further work based on this patchset has been done by Joel. His work
makes pidfds pollable. It finished too late for this merge window. I
would prefer to have it sitting in linux-next for a while and send it
for inclusion during the 5.3 merge window"
* tag 'pidfd-v5.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/brauner/linux:
samples: show race-free pidfd metadata access
signal: support CLONE_PIDFD with pidfd_send_signal
clone: add CLONE_PIDFD
Make anon_inodes unconditional
-----BEGIN PGP SIGNATURE-----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=WZfC
-----END PGP SIGNATURE-----
Merge tag 'printk-for-5.2' of git://git.kernel.org/pub/scm/linux/kernel/git/pmladek/printk
Pull printk updates from Petr Mladek:
- Allow state reset of printk_once() calls.
- Prevent crashes when dereferencing invalid pointers in vsprintf().
Only the first byte is checked for simplicity.
- Make vsprintf warnings consistent and inlined.
- Treewide conversion of obsolete %pf, %pF to %ps, %pF printf
modifiers.
- Some clean up of vsprintf and test_printf code.
* tag 'printk-for-5.2' of git://git.kernel.org/pub/scm/linux/kernel/git/pmladek/printk:
lib/vsprintf: Make function pointer_string static
vsprintf: Limit the length of inlined error messages
vsprintf: Avoid confusion between invalid address and value
vsprintf: Prevent crash when dereferencing invalid pointers
vsprintf: Consolidate handling of unknown pointer specifiers
vsprintf: Factor out %pO handler as kobject_string()
vsprintf: Factor out %pV handler as va_format()
vsprintf: Factor out %p[iI] handler as ip_addr_string()
vsprintf: Do not check address of well-known strings
vsprintf: Consistent %pK handling for kptr_restrict == 0
vsprintf: Shuffle restricted_pointer()
printk: Tie printk_once / printk_deferred_once into .data.once for reset
treewide: Switch printk users from %pf and %pF to %ps and %pS, respectively
lib/test_printf: Switch to bitmap_zalloc()
Poking-mm initialization might require to duplicate the PGD in early
stage. Initialize the PGD cache earlier to prevent boot failures.
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Nadav Amit <namit@vmware.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Rick Edgecombe <rick.p.edgecombe@intel.com>
Cc: Rik van Riel <riel@surriel.com>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Thomas Gleixner <tglx@linutronix.de>
Fixes: 4fc19708b1 ("x86/alternatives: Initialize temporary mm for patching")
Link: http://lkml.kernel.org/r/20190505011124.39692-1-namit@vmware.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
To prevent improper use of the PTEs that are used for text patching, the
next patches will use a temporary mm struct. Initailize it by copying
the init mm.
The address that will be used for patching is taken from the lower area
that is usually used for the task memory. Doing so prevents the need to
frequently synchronize the temporary-mm (e.g., when BPF programs are
installed), since different PGDs are used for the task memory.
Finally, randomize the address of the PTEs to harden against exploits
that use these PTEs.
Suggested-by: Andy Lutomirski <luto@kernel.org>
Tested-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Nadav Amit <namit@vmware.com>
Signed-off-by: Rick Edgecombe <rick.p.edgecombe@intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Rik van Riel <riel@surriel.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: akpm@linux-foundation.org
Cc: ard.biesheuvel@linaro.org
Cc: deneen.t.dock@intel.com
Cc: kernel-hardening@lists.openwall.com
Cc: kristen@linux.intel.com
Cc: linux_dti@icloud.com
Cc: will.deacon@arm.com
Link: https://lkml.kernel.org/r/20190426232303.28381-8-nadav.amit@gmail.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Since commit 13610aa908 ("kernel/configs: use .incbin directive to
embed config_data.gz"), IKCONFIG no longer uses BUILD_BIN2C so prevent
it from being selected in Kconfig.
Reviewed-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Joel Fernandes (Google) <joel@joelfernandes.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Introduce in-kernel headers which are made available as an archive
through proc (/proc/kheaders.tar.xz file). This archive makes it
possible to run eBPF and other tracing programs that need to extend the
kernel for tracing purposes without any dependency on the file system
having headers.
A github PR is sent for the corresponding BCC patch at:
https://github.com/iovisor/bcc/pull/2312
On Android and embedded systems, it is common to switch kernels but not
have kernel headers available on the file system. Further once a
different kernel is booted, any headers stored on the file system will
no longer be useful. This is an issue even well known to distros.
By storing the headers as a compressed archive within the kernel, we can
avoid these issues that have been a hindrance for a long time.
The best way to use this feature is by building it in. Several users
have a need for this, when they switch debug kernels, they do not want to
update the filesystem or worry about it where to store the headers on
it. However, the feature is also buildable as a module in case the user
desires it not being part of the kernel image. This makes it possible to
load and unload the headers from memory on demand. A tracing program can
load the module, do its operations, and then unload the module to save
kernel memory. The total memory needed is 3.3MB.
By having the archive available at a fixed location independent of
filesystem dependencies and conventions, all debugging tools can
directly refer to the fixed location for the archive, without concerning
with where the headers on a typical filesystem which significantly
simplifies tooling that needs kernel headers.
The code to read the headers is based on /proc/config.gz code and uses
the same technique to embed the headers.
Other approaches were discussed such as having an in-memory mountable
filesystem, but that has drawbacks such as requiring an in-kernel xz
decompressor which we don't have today, and requiring usage of 42 MB of
kernel memory to host the decompressed headers at anytime. Also this
approach is simpler than such approaches.
Reviewed-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Joel Fernandes (Google) <joel@joelfernandes.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Right now rand_initialize() is run as an early_initcall(), but it only
depends on timekeeping_init() (for mixing ktime_get_real() into the
pools). However, the call to boot_init_stack_canary() for stack canary
initialization runs earlier, which triggers a warning at boot:
random: get_random_bytes called from start_kernel+0x357/0x548 with crng_init=0
Instead, this moves rand_initialize() to after timekeeping_init(), and moves
canary initialization here as well.
Note that this warning may still remain for machines that do not have
UEFI RNG support (which initializes the RNG pools during setup_arch()),
or for x86 machines without RDRAND (or booting without "random.trust=on"
or CONFIG_RANDOM_TRUST_CPU=y).
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
When a module option, or core kernel argument, toggles a static-key it
requires jump labels to be initialized early. While x86, PowerPC, and
ARM64 arrange for jump_label_init() to be called before parse_args(),
ARM does not.
Kernel command line: rdinit=/sbin/init page_alloc.shuffle=1 panic=-1 console=ttyAMA0,115200 page_alloc.shuffle=1
------------[ cut here ]------------
WARNING: CPU: 0 PID: 0 at ./include/linux/jump_label.h:303
page_alloc_shuffle+0x12c/0x1ac
static_key_enable(): static key 'page_alloc_shuffle_key+0x0/0x4' used
before call to jump_label_init()
Modules linked in:
CPU: 0 PID: 0 Comm: swapper Not tainted
5.1.0-rc4-next-20190410-00003-g3367c36ce744 #1
Hardware name: ARM Integrator/CP (Device Tree)
[<c0011c68>] (unwind_backtrace) from [<c000ec48>] (show_stack+0x10/0x18)
[<c000ec48>] (show_stack) from [<c07e9710>] (dump_stack+0x18/0x24)
[<c07e9710>] (dump_stack) from [<c001bb1c>] (__warn+0xe0/0x108)
[<c001bb1c>] (__warn) from [<c001bb88>] (warn_slowpath_fmt+0x44/0x6c)
[<c001bb88>] (warn_slowpath_fmt) from [<c0b0c4a8>]
(page_alloc_shuffle+0x12c/0x1ac)
[<c0b0c4a8>] (page_alloc_shuffle) from [<c0b0c550>] (shuffle_store+0x28/0x48)
[<c0b0c550>] (shuffle_store) from [<c003e6a0>] (parse_args+0x1f4/0x350)
[<c003e6a0>] (parse_args) from [<c0ac3c00>] (start_kernel+0x1c0/0x488)
Move the fallback call to jump_label_init() to occur before
parse_args().
The redundant calls to jump_label_init() in other archs are left intact
in case they have static key toggling use cases that are even earlier
than option parsing.
Link: http://lkml.kernel.org/r/155544804466.1032396.13418949511615676665.stgit@dwillia2-desk3.amr.corp.intel.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Reported-by: Guenter Roeck <groeck@google.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Mike Rapoport <rppt@linux.ibm.com>
Cc: Russell King <rmk@armlinux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Make the anon_inodes facility unconditional so that it can be used by core
VFS code and pidfd code.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
[christian@brauner.io: adapt commit message to mention pidfds]
Signed-off-by: Christian Brauner <christian@brauner.io>
Add panic() calls if memblock_alloc() returns NULL.
The panic() format duplicates the one used by memblock itself and in
order to avoid explosion with long parameters list replace open coded
allocation size calculations with a local variable.
Link: http://lkml.kernel.org/r/1548057848-15136-18-git-send-email-rppt@linux.ibm.com
Signed-off-by: Mike Rapoport <rppt@linux.ibm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Christophe Leroy <christophe.leroy@c-s.fr>
Cc: Christoph Hellwig <hch@lst.de>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Dennis Zhou <dennis@kernel.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Greentime Hu <green.hu@gmail.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Guan Xuetao <gxt@pku.edu.cn>
Cc: Guo Ren <guoren@kernel.org>
Cc: Guo Ren <ren_guo@c-sky.com> [c-sky]
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Juergen Gross <jgross@suse.com> [Xen]
Cc: Mark Salter <msalter@redhat.com>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Max Filippov <jcmvbkbc@gmail.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Paul Burton <paul.burton@mips.com>
Cc: Petr Mladek <pmladek@suse.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Rich Felker <dalias@libc.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Rob Herring <robh@kernel.org>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Stafford Horne <shorne@gmail.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- do not generate unneeded top-level built-in.a
- let git ignore O= directory entirely
- optimize scripts/kallsyms slightly
- exclude DWARF info from *.s regardless of config options
- fix GCC toolchain search path for Clang to prepare ld.lld support
- do not generate modules.order when CONFIG_MODULES is disabled
- simplify single target rules and remove VPATH for external module build
- allow to add optional flags to dpkg-buildpackage when building deb-pkg
- move some compiler option tests from Makefile to Kconfig
- various Makefile cleanups
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=y9YG
-----END PGP SIGNATURE-----
Merge tag 'kbuild-v5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild
Pull Kbuild updates from Masahiro Yamada:
- do not generate unneeded top-level built-in.a
- let git ignore O= directory entirely
- optimize scripts/kallsyms slightly
- exclude DWARF info from *.s regardless of config options
- fix GCC toolchain search path for Clang to prepare ld.lld support
- do not generate modules.order when CONFIG_MODULES is disabled
- simplify single target rules and remove VPATH for external module
build
- allow to add optional flags to dpkg-buildpackage when building
deb-pkg
- move some compiler option tests from Makefile to Kconfig
- various Makefile cleanups
* tag 'kbuild-v5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild: (40 commits)
kbuild: remove scripts/basic/% build target
kbuild: use -Werror=implicit-... instead of -Werror-implicit-...
kbuild: clean up scripts/gcc-version.sh
kbuild: remove cc-version macro
kbuild: update comment block of scripts/clang-version.sh
kbuild: remove commented-out INITRD_COMPRESS
kbuild: move -gsplit-dwarf, -gdwarf-4 option tests to Kconfig
kbuild: [bin]deb-pkg: add DPKG_FLAGS variable
kbuild: move ".config not found!" message from Kconfig to Makefile
kbuild: invoke syncconfig if include/config/auto.conf.cmd is missing
kbuild: simplify single target rules
kbuild: remove empty rules for makefiles
kbuild: make -r/-R effective in top Makefile for old Make versions
kbuild: move tools_silent to a more relevant place
kbuild: compute false-positive -Wmaybe-uninitialized cases in Kconfig
kbuild: refactor cc-cross-prefix implementation
kbuild: hardcode genksyms path and remove GENKSYMS variable
scripts/gdb: refactor rules for symlink creation
kbuild: create symlink to vmlinux-gdb.py in scripts_gdb target
scripts/gdb: do not descend into scripts/gdb from scripts
...
Pull timer fix from Thomas Gleixner:
"A single fix to prevent a unmet dependencies warning in Kconfig"
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
time: Make VIRT_CPU_ACCOUNTING_GEN depend on GENERIC_CLOCKEVENTS
-----BEGIN PGP SIGNATURE-----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=p78E
-----END PGP SIGNATURE-----
Merge tag 'io_uring-2019-03-06' of git://git.kernel.dk/linux-block
Pull io_uring IO interface from Jens Axboe:
"Second attempt at adding the io_uring interface.
Since the first one, we've added basic unit testing of the three
system calls, that resides in liburing like the other unit tests that
we have so far. It'll take a while to get full coverage of it, but
we're working towards it. I've also added two basic test programs to
tools/io_uring. One uses the raw interface and has support for all the
various features that io_uring supports outside of standard IO, like
fixed files, fixed IO buffers, and polled IO. The other uses the
liburing API, and is a simplified version of cp(1).
This adds support for a new IO interface, io_uring.
io_uring allows an application to communicate with the kernel through
two rings, the submission queue (SQ) and completion queue (CQ) ring.
This allows for very efficient handling of IOs, see the v5 posting for
some basic numbers:
https://lore.kernel.org/linux-block/20190116175003.17880-1-axboe@kernel.dk/
Outside of just efficiency, the interface is also flexible and
extendable, and allows for future use cases like the upcoming NVMe
key-value store API, networked IO, and so on. It also supports async
buffered IO, something that we've always failed to support in the
kernel.
Outside of basic IO features, it supports async polled IO as well.
This particular feature has already been tested at Facebook months ago
for flash storage boxes, with 25-33% improvements. It makes polled IO
actually useful for real world use cases, where even basic flash sees
a nice win in terms of efficiency, latency, and performance. These
boxes were IOPS bound before, now they are not.
This series adds three new system calls. One for setting up an
io_uring instance (io_uring_setup(2)), one for submitting/completing
IO (io_uring_enter(2)), and one for aux functions like registrating
file sets, buffers, etc (io_uring_register(2)). Through the help of
Arnd, I've coordinated the syscall numbers so merge on that front
should be painless.
Jon did a writeup of the interface a while back, which (except for
minor details that have been tweaked) is still accurate. Find that
here:
https://lwn.net/Articles/776703/
Huge thanks to Al Viro for helping getting the reference cycle code
correct, and to Jann Horn for his extensive reviews focused on both
security and bugs in general.
There's a userspace library that provides basic functionality for
applications that don't need or want to care about how to fiddle with
the rings directly. It has helpers to allow applications to easily set
up an io_uring instance, and submit/complete IO through it without
knowing about the intricacies of the rings. It also includes man pages
(thanks to Jeff Moyer), and will continue to grow support helper
functions and features as time progresses. Find it here:
git://git.kernel.dk/liburing
Fio has full support for the raw interface, both in the form of an IO
engine (io_uring), but also with a small test application (t/io_uring)
that can exercise and benchmark the interface"
* tag 'io_uring-2019-03-06' of git://git.kernel.dk/linux-block:
io_uring: add a few test tools
io_uring: allow workqueue item to handle multiple buffered requests
io_uring: add support for IORING_OP_POLL
io_uring: add io_kiocb ref count
io_uring: add submission polling
io_uring: add file set registration
net: split out functions related to registering inflight socket files
io_uring: add support for pre-mapped user IO buffers
block: implement bio helper to add iter bvec pages to bio
io_uring: batch io_kiocb allocation
io_uring: use fget/fput_many() for file references
fs: add fget_many() and fput_many()
io_uring: support for IO polling
io_uring: add fsync support
Add io_uring IO interface
Merge more updates from Andrew Morton:
- some of the rest of MM
- various misc things
- dynamic-debug updates
- checkpatch
- some epoll speedups
- autofs
- rapidio
- lib/, lib/lzo/ updates
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (83 commits)
samples/mic/mpssd/mpssd.h: remove duplicate header
kernel/fork.c: remove duplicated include
include/linux/relay.h: fix percpu annotation in struct rchan
arch/nios2/mm/fault.c: remove duplicate include
unicore32: stop printing the virtual memory layout
MAINTAINERS: fix GTA02 entry and mark as orphan
mm: create the new vm_fault_t type
arm, s390, unicore32: remove oneliner wrappers for memblock_alloc()
arch: simplify several early memory allocations
openrisc: simplify pte_alloc_one_kernel()
sh: prefer memblock APIs returning virtual address
microblaze: prefer memblock API returning virtual address
powerpc: prefer memblock APIs returning virtual address
lib/lzo: separate lzo-rle from lzo
lib/lzo: implement run-length encoding
lib/lzo: fast 8-byte copy on arm64
lib/lzo: 64-bit CTZ on arm64
lib/lzo: tidy-up ifdefs
ipc/sem.c: replace kvmalloc/memset with kvzalloc and use struct_size
ipc: annotate implicit fall through
...
-----BEGIN PGP SIGNATURE-----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=57/1
-----END PGP SIGNATURE-----
Merge tag 'audit-pr-20190305' of git://git.kernel.org/pub/scm/linux/kernel/git/pcmoore/audit
Pull audit updates from Paul Moore:
"A lucky 13 audit patches for v5.1.
Despite the rather large diffstat, most of the changes are from two
bug fix patches that move code from one Kconfig option to another.
Beyond that bit of churn, the remaining changes are largely cleanups
and bug-fixes as we slowly march towards container auditing. It isn't
all boring though, we do have a couple of new things: file
capabilities v3 support, and expanded support for filtering on
filesystems to solve problems with remote filesystems.
All changes pass the audit-testsuite. Please merge for v5.1"
* tag 'audit-pr-20190305' of git://git.kernel.org/pub/scm/linux/kernel/git/pcmoore/audit:
audit: mark expected switch fall-through
audit: hide auditsc_get_stamp and audit_serial prototypes
audit: join tty records to their syscall
audit: remove audit_context when CONFIG_ AUDIT and not AUDITSYSCALL
audit: remove unused actx param from audit_rule_match
audit: ignore fcaps on umount
audit: clean up AUDITSYSCALL prototypes and stubs
audit: more filter PATH records keyed on filesystem magic
audit: add support for fcaps v3
audit: move loginuid and sessionid from CONFIG_AUDITSYSCALL to CONFIG_AUDIT
audit: add syscall information to CONFIG_CHANGE records
audit: hand taken context to audit_kill_trees for syscall logging
audit: give a clue what CONFIG_CHANGE op was involved
Moving the CONTEXT_TRACKING Kconfig option into kernel/time/Kconfig added
an implicit dependency on the surrounding GENERIC_CLOCKEVENTS option, but
this is not always enabled when it is possible to select
VIRT_CPU_ACCOUNTING_GEN:
WARNING: unmet direct dependencies detected for CONTEXT_TRACKING
Depends on [n]: GENERIC_CLOCKEVENTS [=n]
Selected by [y]:
- VIRT_CPU_ACCOUNTING_GEN [=y] && <choice> && HAVE_CONTEXT_TRACKING [=y] && HAVE_VIRT_CPU_ACCOUNTING_GEN [=y]
Platforms without GENERIC_CLOCKEVENTS are rare enough so that corner case
can be just ignored. Make it a dependency for VIRT_CPU_ACCOUNTING_GEN to
simplify the configuration.
Fixes: a4cffdad73 ("time: Move CONTEXT_TRACKING to kernel/time/Kconfig")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: "Paul E . McKenney" <paulmck@linux.ibm.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Link: https://lkml.kernel.org/r/20190304200202.1163250-1-arnd@arndb.de
Merge misc updates from Andrew Morton:
- a few misc things
- ocfs2 updates
- most of MM
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (159 commits)
tools/testing/selftests/proc/proc-self-syscall.c: remove duplicate include
proc: more robust bulk read test
proc: test /proc/*/maps, smaps, smaps_rollup, statm
proc: use seq_puts() everywhere
proc: read kernel cpu stat pointer once
proc: remove unused argument in proc_pid_lookup()
fs/proc/thread_self.c: code cleanup for proc_setup_thread_self()
fs/proc/self.c: code cleanup for proc_setup_self()
proc: return exit code 4 for skipped tests
mm,mremap: bail out earlier in mremap_to under map pressure
mm/sparse: fix a bad comparison
mm/memory.c: do_fault: avoid usage of stale vm_area_struct
writeback: fix inode cgroup switching comment
mm/huge_memory.c: fix "orig_pud" set but not used
mm/hotplug: fix an imbalance with DEBUG_PAGEALLOC
mm/memcontrol.c: fix bad line in comment
mm/cma.c: cma_declare_contiguous: correct err handling
mm/page_ext.c: fix an imbalance with kmemleak
mm/compaction: pass pgdat to too_many_isolated() instead of zone
mm: remove zone_lru_lock() function, access ->lru_lock directly
...
Pull scheduler updates from Ingo Molnar:
"The main changes in this cycle were:
- refcount conversions
- Solve the rq->leaf_cfs_rq_list can of worms for real.
- improve power-aware scheduling
- add sysctl knob for Energy Aware Scheduling
- documentation updates
- misc other changes"
* 'sched-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (34 commits)
kthread: Do not use TIMER_IRQSAFE
kthread: Convert worker lock to raw spinlock
sched/fair: Use non-atomic cpumask_{set,clear}_cpu()
sched/fair: Remove unused 'sd' parameter from select_idle_smt()
sched/wait: Use freezable_schedule() when possible
sched/fair: Prune, fix and simplify the nohz_balancer_kick() comment block
sched/fair: Explain LLC nohz kick condition
sched/fair: Simplify nohz_balancer_kick()
sched/topology: Fix percpu data types in struct sd_data & struct s_data
sched/fair: Simplify post_init_entity_util_avg() by calling it with a task_struct pointer argument
sched/fair: Fix O(nr_cgroups) in the load balancing path
sched/fair: Optimize update_blocked_averages()
sched/fair: Fix insertion in rq->leaf_cfs_rq_list
sched/fair: Add tmp_alone_branch assertion
sched/core: Use READ_ONCE()/WRITE_ONCE() in move_queued_task()/task_rq_lock()
sched/debug: Initialize sd_sysctl_cpus if !CONFIG_CPUMASK_OFFSTACK
sched/pelt: Skip updating util_est when utilization is higher than CPU's capacity
sched/fair: Update scale invariance of PELT
sched/fair: Move the rq_of() helper function
sched/core: Convert task_struct.stack_refcount to refcount_t
...
Patch series "Replace all open encodings for NUMA_NO_NODE", v3.
All these places for replacement were found by running the following
grep patterns on the entire kernel code. Please let me know if this
might have missed some instances. This might also have replaced some
false positives. I will appreciate suggestions, inputs and review.
1. git grep "nid == -1"
2. git grep "node == -1"
3. git grep "nid = -1"
4. git grep "node = -1"
This patch (of 2):
At present there are multiple places where invalid node number is
encoded as -1. Even though implicitly understood it is always better to
have macros in there. Replace these open encodings for an invalid node
number with the global macro NUMA_NO_NODE. This helps remove NUMA
related assumptions like 'invalid node' from various places redirecting
them to a common definition.
Link: http://lkml.kernel.org/r/1545127933-10711-2-git-send-email-anshuman.khandual@arm.com
Signed-off-by: Anshuman Khandual <anshuman.khandual@arm.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> [ixgbe]
Acked-by: Jens Axboe <axboe@kernel.dk> [mtip32xx]
Acked-by: Vinod Koul <vkoul@kernel.org> [dmaengine.c]
Acked-by: Michael Ellerman <mpe@ellerman.id.au> [powerpc]
Acked-by: Doug Ledford <dledford@redhat.com> [drivers/infiniband]
Cc: Joseph Qi <jiangqi903@gmail.com>
Cc: Hans Verkuil <hverkuil@xs4all.nl>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Now that the Kconfig is the only user of this script, we can drop
unneeded code.
Remove the -p option, and stop prepending the output with zero,
so that Kconfig can directly use the output from this script.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The submission queue (SQ) and completion queue (CQ) rings are shared
between the application and the kernel. This eliminates the need to
copy data back and forth to submit and complete IO.
IO submissions use the io_uring_sqe data structure, and completions
are generated in the form of io_uring_cqe data structures. The SQ
ring is an index into the io_uring_sqe array, which makes it possible
to submit a batch of IOs without them being contiguous in the ring.
The CQ ring is always contiguous, as completion events are inherently
unordered, and hence any io_uring_cqe entry can point back to an
arbitrary submission.
Two new system calls are added for this:
io_uring_setup(entries, params)
Sets up an io_uring instance for doing async IO. On success,
returns a file descriptor that the application can mmap to
gain access to the SQ ring, CQ ring, and io_uring_sqes.
io_uring_enter(fd, to_submit, min_complete, flags, sigset, sigsetsize)
Initiates IO against the rings mapped to this fd, or waits for
them to complete, or both. The behavior is controlled by the
parameters passed in. If 'to_submit' is non-zero, then we'll
try and submit new IO. If IORING_ENTER_GETEVENTS is set, the
kernel will wait for 'min_complete' events, if they aren't
already available. It's valid to set IORING_ENTER_GETEVENTS
and 'min_complete' == 0 at the same time, this allows the
kernel to return already completed events without waiting
for them. This is useful only for polling, as for IRQ
driven IO, the application can just check the CQ ring
without entering the kernel.
With this setup, it's possible to do async IO with a single system
call. Future developments will enable polled IO with this interface,
and polled submission as well. The latter will enable an application
to do IO without doing ANY system calls at all.
For IRQ driven IO, an application only needs to enter the kernel for
completions if it wants to wait for them to occur.
Each io_uring is backed by a workqueue, to support buffered async IO
as well. We will only punt to an async context if the command would
need to wait for IO on the device side. Any data that can be accessed
directly in the page cache is done inline. This avoids the slowness
issue of usual threadpools, since cached data is accessed as quickly
as a sync interface.
Sample application: http://git.kernel.dk/cgit/fio/plain/t/io_uring.c
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Since -Wmaybe-uninitialized was introduced by GCC 4.7, we have patched
various false positives:
- commit e74fc973b6 ("Turn off -Wmaybe-uninitialized when building
with -Os") turned off this option for -Os.
- commit 815eb71e71 ("Kbuild: disable 'maybe-uninitialized' warning
for CONFIG_PROFILE_ALL_BRANCHES") turned off this option for
CONFIG_PROFILE_ALL_BRANCHES
- commit a76bcf557e ("Kbuild: enable -Wmaybe-uninitialized warning
for "make W=1"") turned off this option for GCC < 4.9
Arnd provided more explanation in https://lkml.org/lkml/2017/3/14/903
I think this looks better by shifting the logic from Makefile to Kconfig.
Link: https://github.com/ClangBuiltLinux/linux/issues/350
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Nathan Chancellor <natechancellor@gmail.com>
Tested-by: Nick Desaulniers <ndesaulniers@google.com>
Revert ff1522bb7d ("initramfs: cleanup incomplete rootfs").
Andy reports
: This breaks my setup where I have U-boot provided more size of initramfs
: than needed. This allows a bit of flexibility to increase or decrease
: initramfs compressed image without taking care of bootloader. The proper
: solution is to do this if we sure that we didn't get enough memory,
: otherwise I can't consider the error fatal to clean up rootfs.
Fixes: ff1522bb7d ("initramfs: cleanup incomplete rootfs")
Reported-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Tested-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: David Engraf <david.engraf@sysgo.com>
Cc: Dominik Brodowski <linux@dominikbrodowski.net>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Philippe Ombredanne <pombredanne@nexb.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Luc Van Oostenryck <luc.vanoostenryck@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This reverts commit fe53ca5427 ("mm: use early_pfn_to_nid in
page_ext_init").
When booting a system with "page_owner=on",
start_kernel
page_ext_init
invoke_init_callbacks
init_section_page_ext
init_page_owner
init_early_allocated_pages
init_zones_in_node
init_pages_in_zone
lookup_page_ext
page_to_nid
The issue here is that page_to_nid() will not work since some page flags
have no node information until later in page_alloc_init_late() due to
DEFERRED_STRUCT_PAGE_INIT. Hence, it could trigger an out-of-bounds
access with an invalid nid.
UBSAN: Undefined behaviour in ./include/linux/mm.h:1104:50
index 7 is out of range for type 'zone [5]'
Also, kernel will panic since flags were poisoned earlier with,
CONFIG_DEBUG_VM_PGFLAGS=y
CONFIG_NODE_NOT_IN_PAGE_FLAGS=n
start_kernel
setup_arch
pagetable_init
paging_init
sparse_init
sparse_init_nid
memblock_alloc_try_nid_raw
It did not handle it well in init_pages_in_zone() which ends up calling
page_to_nid().
page:ffffea0004200000 is uninitialized and poisoned
raw: ffffffffffffffff ffffffffffffffff ffffffffffffffff ffffffffffffffff
raw: ffffffffffffffff ffffffffffffffff ffffffffffffffff ffffffffffffffff
page dumped because: VM_BUG_ON_PAGE(PagePoisoned(p))
page_owner info is not active (free page?)
kernel BUG at include/linux/mm.h:990!
RIP: 0010:init_page_owner+0x486/0x520
This means that assumptions behind commit fe53ca5427 ("mm: use
early_pfn_to_nid in page_ext_init") are incomplete. Therefore, revert
the commit for now. A proper way to move the page_owner initialization
to sooner is to hook into memmap initialization.
Link: http://lkml.kernel.org/r/20190115202812.75820-1-cai@lca.pw
Signed-off-by: Qian Cai <cai@lca.pw>
Acked-by: Michal Hocko <mhocko@kernel.org>
Cc: Pasha Tatashin <Pavel.Tatashin@microsoft.com>
Cc: Mel Gorman <mgorman@techsingularity.net>
Cc: Yang Shi <yang.shi@linaro.org>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
atomic_t variables are currently used to implement reference
counters with the following properties:
- counter is initialized to 1 using atomic_set()
- a resource is freed upon counter reaching zero
- once counter reaches zero, its further
increments aren't allowed
- counter schema uses basic atomic operations
(set, inc, inc_not_zero, dec_and_test, etc.)
Such atomic variables should be converted to a newly provided
refcount_t type and API that prevents accidental counter overflows
and underflows. This is important since overflows and underflows
can lead to use-after-free situation and be exploitable.
The variable task_struct.stack_refcount is used as pure reference counter.
Convert it to refcount_t and fix up the operations.
** Important note for maintainers:
Some functions from refcount_t API defined in lib/refcount.c
have different memory ordering guarantees than their atomic
counterparts.
The full comparison can be seen in
https://lkml.org/lkml/2017/11/15/57 and it is hopefully soon
in state to be merged to the documentation tree.
Normally the differences should not matter since refcount_t provides
enough guarantees to satisfy the refcounting use cases, but in
some rare cases it might matter.
Please double check that you don't have some undocumented
memory guarantees for this variable usage.
For the task_struct.stack_refcount it might make a difference
in following places:
- try_get_task_stack(): increment in refcount_inc_not_zero() only
guarantees control dependency on success vs. fully ordered
atomic counterpart
- put_task_stack(): decrement in refcount_dec_and_test() only
provides RELEASE ordering and control dependency on success
vs. fully ordered atomic counterpart
Suggested-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Elena Reshetova <elena.reshetova@intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: David Windsor <dwindsor@gmail.com>
Reviewed-by: Hans Liljestrand <ishkamiel@gmail.com>
Reviewed-by: Andrea Parri <andrea.parri@amarulasolutions.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: akpm@linux-foundation.org
Cc: viro@zeniv.linux.org.uk
Link: https://lkml.kernel.org/r/1547814450-18902-6-git-send-email-elena.reshetova@intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
atomic_t variables are currently used to implement reference
counters with the following properties:
- counter is initialized to 1 using atomic_set()
- a resource is freed upon counter reaching zero
- once counter reaches zero, its further
increments aren't allowed
- counter schema uses basic atomic operations
(set, inc, inc_not_zero, dec_and_test, etc.)
Such atomic variables should be converted to a newly provided
refcount_t type and API that prevents accidental counter overflows
and underflows. This is important since overflows and underflows
can lead to use-after-free situation and be exploitable.
The variable task_struct.usage is used as pure reference counter.
Convert it to refcount_t and fix up the operations.
** Important note for maintainers:
Some functions from refcount_t API defined in lib/refcount.c
have different memory ordering guarantees than their atomic
counterparts.
The full comparison can be seen in
https://lkml.org/lkml/2017/11/15/57 and it is hopefully soon
in state to be merged to the documentation tree.
Normally the differences should not matter since refcount_t provides
enough guarantees to satisfy the refcounting use cases, but in
some rare cases it might matter.
Please double check that you don't have some undocumented
memory guarantees for this variable usage.
For the task_struct.usage it might make a difference
in following places:
- put_task_struct(): decrement in refcount_dec_and_test() only
provides RELEASE ordering and control dependency on success
vs. fully ordered atomic counterpart
Suggested-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Elena Reshetova <elena.reshetova@intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: David Windsor <dwindsor@gmail.com>
Reviewed-by: Hans Liljestrand <ishkamiel@gmail.com>
Reviewed-by: Andrea Parri <andrea.parri@amarulasolutions.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: akpm@linux-foundation.org
Cc: viro@zeniv.linux.org.uk
Link: https://lkml.kernel.org/r/1547814450-18902-5-git-send-email-elena.reshetova@intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
atomic_t variables are currently used to implement reference
counters with the following properties:
- counter is initialized to 1 using atomic_set()
- a resource is freed upon counter reaching zero
- once counter reaches zero, its further
increments aren't allowed
- counter schema uses basic atomic operations
(set, inc, inc_not_zero, dec_and_test, etc.)
Such atomic variables should be converted to a newly provided
refcount_t type and API that prevents accidental counter overflows
and underflows. This is important since overflows and underflows
can lead to use-after-free situation and be exploitable.
The variable signal_struct.sigcnt is used as pure reference counter.
Convert it to refcount_t and fix up the operations.
** Important note for maintainers:
Some functions from refcount_t API defined in lib/refcount.c
have different memory ordering guarantees than their atomic
counterparts.
The full comparison can be seen in
https://lkml.org/lkml/2017/11/15/57 and it is hopefully soon
in state to be merged to the documentation tree.
Normally the differences should not matter since refcount_t provides
enough guarantees to satisfy the refcounting use cases, but in
some rare cases it might matter.
Please double check that you don't have some undocumented
memory guarantees for this variable usage.
For the signal_struct.sigcnt it might make a difference
in following places:
- put_signal_struct(): decrement in refcount_dec_and_test() only
provides RELEASE ordering and control dependency on success
vs. fully ordered atomic counterpart
Suggested-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Elena Reshetova <elena.reshetova@intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: David Windsor <dwindsor@gmail.com>
Reviewed-by: Hans Liljestrand <ishkamiel@gmail.com>
Reviewed-by: Andrea Parri <andrea.parri@amarulasolutions.com>
Reviewed-by: Oleg Nesterov <oleg@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: akpm@linux-foundation.org
Cc: viro@zeniv.linux.org.uk
Link: https://lkml.kernel.org/r/1547814450-18902-3-git-send-email-elena.reshetova@intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The current help text caused some confusion in online forums about
whether or not to default-enable or default-disable psi in vendor
kernels. This is because it doesn't communicate the reason for why we
made this setting configurable in the first place: that the overhead is
non-zero in an artificial scheduler stress test.
Since this isn't representative of real workloads, and the effect was
not measurable in scheduler-heavy real world applications such as the
webservers and memcache installations at Facebook, it's fair to point
out that this is a pretty cautious option to select.
Link: http://lkml.kernel.org/r/20190129233617.16767-1-hannes@cmpxchg.org
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Reviewed-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Mel Gorman <mgorman@techsingularity.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
loginuid and sessionid (and audit_log_session_info) should be part of
CONFIG_AUDIT scope and not CONFIG_AUDITSYSCALL since it is used in
CONFIG_CHANGE, ANOM_LINK, FEATURE_CHANGE (and INTEGRITY_RULE), none of
which are otherwise dependent on AUDITSYSCALL.
Please see github issue
https://github.com/linux-audit/audit-kernel/issues/104
Signed-off-by: Richard Guy Briggs <rgb@redhat.com>
[PM: tweaked subject line for better grep'ing]
Signed-off-by: Paul Moore <paul@paul-moore.com>
When building using GCC 4.7 or older, -ffunction-sections & the -pg flag
used by ftrace are incompatible. This causes warnings or build failures
(where -Werror applies) such as the following:
arch/mips/generic/init.c:
error: -ffunction-sections disabled; it makes profiling impossible
This used to be taken into account by the ordering of calls to cc-option
from within the top-level Makefile, which was introduced by commit
90ad4052e8 ("kbuild: avoid conflict between -ffunction-sections and
-pg on gcc-4.7"). Unfortunately this was broken when the
CONFIG_LD_DEAD_CODE_DATA_ELIMINATION cc-option check was moved to
Kconfig in commit e85d1d65cd ("kbuild: test dead code/data elimination
support in Kconfig"), because the flags used by this check no longer
include -pg.
Fix this by not allowing CONFIG_LD_DEAD_CODE_DATA_ELIMINATION to be
enabled at the same time as ftrace/CONFIG_FUNCTION_TRACER when building
using GCC 4.7 or older.
Signed-off-by: Paul Burton <paul.burton@mips.com>
Fixes: e85d1d65cd ("kbuild: test dead code/data elimination support in Kconfig")
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Nicholas Piggin <npiggin@gmail.com>
Cc: stable@vger.kernel.org # v4.19+
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Currently, CONFIG_JUMP_LABEL just means "I _want_ to use jump label".
The jump label is controlled by HAVE_JUMP_LABEL, which is defined
like this:
#if defined(CC_HAVE_ASM_GOTO) && defined(CONFIG_JUMP_LABEL)
# define HAVE_JUMP_LABEL
#endif
We can improve this by testing 'asm goto' support in Kconfig, then
make JUMP_LABEL depend on CC_HAS_ASM_GOTO.
Ugly #ifdef HAVE_JUMP_LABEL will go away, and CONFIG_JUMP_LABEL will
match to the real kernel capability.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Michael Ellerman <mpe@ellerman.id.au> (powerpc)
Tested-by: Sedat Dilek <sedat.dilek@gmail.com>
Pull vfs mount API prep from Al Viro:
"Mount API prereqs.
Mostly that's LSM mount options cleanups. There are several minor
fixes in there, but nothing earth-shattering (leaks on failure exits,
mostly)"
* 'mount.part1' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (27 commits)
mount_fs: suppress MAC on MS_SUBMOUNT as well as MS_KERNMOUNT
smack: rewrite smack_sb_eat_lsm_opts()
smack: get rid of match_token()
smack: take the guts of smack_parse_opts_str() into a new helper
LSM: new method: ->sb_add_mnt_opt()
selinux: rewrite selinux_sb_eat_lsm_opts()
selinux: regularize Opt_... names a bit
selinux: switch away from match_token()
selinux: new helper - selinux_add_opt()
LSM: bury struct security_mnt_opts
smack: switch to private smack_mnt_opts
selinux: switch to private struct selinux_mnt_opts
LSM: hide struct security_mnt_opts from any generic code
selinux: kill selinux_sb_get_mnt_opts()
LSM: turn sb_eat_lsm_opts() into a method
nfs_remount(): don't leak, don't ignore LSM options quietly
btrfs: sanitize security_mnt_opts use
selinux; don't open-code a loop in sb_finish_set_opts()
LSM: split ->sb_set_mnt_opts() out of ->sb_kern_mount()
new helper: security_sb_eat_lsm_opts()
...
Unpacking an external initrd may fail e.g. not enough memory. This
leads to an incomplete rootfs because some files might be extracted
already. Fixed by cleaning the rootfs so the kernel is not using an
incomplete rootfs.
Link: http://lkml.kernel.org/r/20181030151805.5519-1-david.engraf@sysgo.com
Signed-off-by: David Engraf <david.engraf@sysgo.com>
Cc: Dominik Brodowski <linux@dominikbrodowski.net>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Philippe Ombredanne <pombredanne@nexb.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Luc Van Oostenryck <luc.vanoostenryck@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We get a warning when building kernel with W=1:
kernel/fork.c:167:13: warning: no previous prototype for `arch_release_thread_stack' [-Wmissing-prototypes]
kernel/fork.c:779:13: warning: no previous prototype for `fork_init' [-Wmissing-prototypes]
Add the missing declaration in head file to fix this.
Also, remove arch_release_thread_stack() completely because no arch
seems to implement it since bb9d81264 (arch: remove tile port).
Link: http://lkml.kernel.org/r/1542170087-23645-1-git-send-email-wang.yi59@zte.com.cn
Signed-off-by: Yi Wang <wang.yi59@zte.com.cn>
Acked-by: Michal Hocko <mhocko@suse.com>
Acked-by: Mike Rapoport <rppt@linux.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Initcall names should not be changed.
Link: http://lkml.kernel.org/r/20181124091829.GD10969@avx2
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Reviewed-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull Devicetree updates from Rob Herring:
"The biggest highlight here is the start of using json-schema for DT
bindings. Being able to validate bindings has been discussed for years
with little progress.
- Initial support for DT bindings using json-schema language. This is
the start of converting DT bindings from free-form text to a
structured format.
- Reworking of initrd address initialization. This moves to using the
phys address instead of virt addr in the DT parsing code. This
rework was motivated by CONFIG_DEV_BLK_INITRD causing unnecessary
rebuilding of lots of files.
- Fix stale phandle entries in phandle cache
- DT overlay validation improvements. This exposed several memory
leak bugs which have been fixed.
- Use node name and device_type helper functions in DT code
- Last remaining conversions to using %pOFn printk specifier instead
of device_node.name directly
- Create new common RTC binding doc and move all trivial RTC devices
out of trivial-devices.txt.
- New bindings for Freescale MAG3110 magnetometer, Cadence Sierra
PHY, and Xen shared memory
- Update dtc to upstream version v1.4.7-57-gf267e674d145"
* tag 'devicetree-for-4.21' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (68 commits)
of: __of_detach_node() - remove node from phandle cache
of: of_node_get()/of_node_put() nodes held in phandle cache
gpio-omap.txt: add reg and interrupts properties
dt-bindings: mrvl,intc: fix a trivial typo
dt-bindings: iio: magnetometer: add dt-bindings for freescale mag3110
dt-bindings: Convert trivial-devices.txt to json-schema
dt-bindings: arm: mrvl: amend Browstone compatible string
dt-bindings: arm: Convert Tegra board/soc bindings to json-schema
dt-bindings: arm: Convert ZTE board/soc bindings to json-schema
dt-bindings: arm: Add missing Xilinx boards
dt-bindings: arm: Convert Xilinx board/soc bindings to json-schema
dt-bindings: arm: Convert VIA board/soc bindings to json-schema
dt-bindings: arm: Convert ST STi board/soc bindings to json-schema
dt-bindings: arm: Convert SPEAr board/soc bindings to json-schema
dt-bindings: arm: Convert CSR SiRF board/soc bindings to json-schema
dt-bindings: arm: Convert QCom board/soc bindings to json-schema
dt-bindings: arm: Convert TI nspire board/soc bindings to json-schema
dt-bindings: arm: Convert TI davinci board/soc bindings to json-schema
dt-bindings: arm: Convert Calxeda board/soc bindings to json-schema
dt-bindings: arm: Convert Altera board/soc bindings to json-schema
...
Merge misc updates from Andrew Morton:
- large KASAN update to use arm's "software tag-based mode"
- a few misc things
- sh updates
- ocfs2 updates
- just about all of MM
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (167 commits)
kernel/fork.c: mark 'stack_vm_area' with __maybe_unused
memcg, oom: notify on oom killer invocation from the charge path
mm, swap: fix swapoff with KSM pages
include/linux/gfp.h: fix typo
mm/hmm: fix memremap.h, move dev_page_fault_t callback to hmm
hugetlbfs: Use i_mmap_rwsem to fix page fault/truncate race
hugetlbfs: use i_mmap_rwsem for more pmd sharing synchronization
memory_hotplug: add missing newlines to debugging output
mm: remove __hugepage_set_anon_rmap()
include/linux/vmstat.h: remove unused page state adjustment macro
mm/page_alloc.c: allow error injection
mm: migrate: drop unused argument of migrate_page_move_mapping()
blkdev: avoid migration stalls for blkdev pages
mm: migrate: provide buffer_migrate_page_norefs()
mm: migrate: move migrate_page_lock_buffers()
mm: migrate: lock buffers before migrate_page_move_mapping()
mm: migration: factor out code to compute expected number of page references
mm, page_alloc: enable pcpu_drain with zone capability
kmemleak: add config to select auto scan
mm/page_alloc.c: don't call kasan_free_pages() at deferred mem init
...
-----BEGIN PGP SIGNATURE-----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=TRdW
-----END PGP SIGNATURE-----
Merge tag 'for-4.21/block-20181221' of git://git.kernel.dk/linux-block
Pull block updates from Jens Axboe:
"This is the main pull request for block/storage for 4.21.
Larger than usual, it was a busy round with lots of goodies queued up.
Most notable is the removal of the old IO stack, which has been a long
time coming. No new features for a while, everything coming in this
week has all been fixes for things that were previously merged.
This contains:
- Use atomic counters instead of semaphores for mtip32xx (Arnd)
- Cleanup of the mtip32xx request setup (Christoph)
- Fix for circular locking dependency in loop (Jan, Tetsuo)
- bcache (Coly, Guoju, Shenghui)
* Optimizations for writeback caching
* Various fixes and improvements
- nvme (Chaitanya, Christoph, Sagi, Jay, me, Keith)
* host and target support for NVMe over TCP
* Error log page support
* Support for separate read/write/poll queues
* Much improved polling
* discard OOM fallback
* Tracepoint improvements
- lightnvm (Hans, Hua, Igor, Matias, Javier)
* Igor added packed metadata to pblk. Now drives without metadata
per LBA can be used as well.
* Fix from Geert on uninitialized value on chunk metadata reads.
* Fixes from Hans and Javier to pblk recovery and write path.
* Fix from Hua Su to fix a race condition in the pblk recovery
code.
* Scan optimization added to pblk recovery from Zhoujie.
* Small geometry cleanup from me.
- Conversion of the last few drivers that used the legacy path to
blk-mq (me)
- Removal of legacy IO path in SCSI (me, Christoph)
- Removal of legacy IO stack and schedulers (me)
- Support for much better polling, now without interrupts at all.
blk-mq adds support for multiple queue maps, which enables us to
have a map per type. This in turn enables nvme to have separate
completion queues for polling, which can then be interrupt-less.
Also means we're ready for async polled IO, which is hopefully
coming in the next release.
- Killing of (now) unused block exports (Christoph)
- Unification of the blk-rq-qos and blk-wbt wait handling (Josef)
- Support for zoned testing with null_blk (Masato)
- sx8 conversion to per-host tag sets (Christoph)
- IO priority improvements (Damien)
- mq-deadline zoned fix (Damien)
- Ref count blkcg series (Dennis)
- Lots of blk-mq improvements and speedups (me)
- sbitmap scalability improvements (me)
- Make core inflight IO accounting per-cpu (Mikulas)
- Export timeout setting in sysfs (Weiping)
- Cleanup the direct issue path (Jianchao)
- Export blk-wbt internals in block debugfs for easier debugging
(Ming)
- Lots of other fixes and improvements"
* tag 'for-4.21/block-20181221' of git://git.kernel.dk/linux-block: (364 commits)
kyber: use sbitmap add_wait_queue/list_del wait helpers
sbitmap: add helpers for add/del wait queue handling
block: save irq state in blkg_lookup_create()
dm: don't reuse bio for flushes
nvme-pci: trace SQ status on completions
nvme-rdma: implement polling queue map
nvme-fabrics: allow user to pass in nr_poll_queues
nvme-fabrics: allow nvmf_connect_io_queue to poll
nvme-core: optionally poll sync commands
block: make request_to_qc_t public
nvme-tcp: fix spelling mistake "attepmpt" -> "attempt"
nvme-tcp: fix endianess annotations
nvmet-tcp: fix endianess annotations
nvme-pci: refactor nvme_poll_irqdisable to make sparse happy
nvme-pci: only set nr_maps to 2 if poll queues are supported
nvmet: use a macro for default error location
nvmet: fix comparison of a u16 with -1
blk-mq: enable IO poll if .nr_queues of type poll > 0
blk-mq: change blk_mq_queue_busy() to blk_mq_queue_inflight()
blk-mq: skip zero-queue maps in blk_mq_map_swqueue
...
The current value of the early boot static pool size, 1024 is not big
enough for systems with large number of CPUs with timer or/and workqueue
objects selected. As the results, systems have 60+ CPUs with both timer
and workqueue objects enabled could trigger "ODEBUG: Out of memory.
ODEBUG disabled".
Some debug objects are allocated during the early boot. Enabling some
options like timers or workqueue objects may increase the size required
significantly with large number of CPUs. For example,
CONFIG_DEBUG_OBJECTS_TIMERS:
No. CPUs x 2 (worker pool) objects:
start_kernel
workqueue_init_early
init_worker_pool
init_timer_key
debug_object_init
plus No. CPUs objects (CONFIG_HIGH_RES_TIMERS):
sched_init
hrtick_rq_init
hrtimer_init
CONFIG_DEBUG_OBJECTS_WORK:
No. CPUs objects:
vmalloc_init
__init_work
plus No. CPUs x 6 (workqueue) objects:
workqueue_init_early
alloc_workqueue
__alloc_workqueue_key
alloc_and_link_pwqs
init_pwq
Also, plus No. CPUs objects:
perf_event_init
__init_srcu_struct
init_srcu_struct_fields
init_srcu_struct_nodes
__init_work
However, none of the things are actually used or required before
debug_objects_mem_init() is invoked, so just move the call right before
vmalloc_init().
According to tglx, "the reason why the call is at this place in
start_kernel() is historical. It's because back in the days when
debugobjects were added the memory allocator was enabled way later than
today."
Link: http://lkml.kernel.org/r/20181126102407.1836-1-cai@gmx.us
Signed-off-by: Qian Cai <cai@gmx.us>
Suggested-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Waiman Long <longman@redhat.com>
Cc: Yang Shi <yang.shi@linux.alibaba.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
-----BEGIN PGP SIGNATURE-----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=PCHx
-----END PGP SIGNATURE-----
Merge tag 'audit-pr-20181224' of git://git.kernel.org/pub/scm/linux/kernel/git/pcmoore/audit
Pull audit updates from Paul Moore:
"In the finest of holiday of traditions, I have a number of gifts to
share today. While most of them are re-gifts from others, unlike the
typical re-gift, these are things you will want in and around your
tree; I promise.
This pull request is perhaps a bit larger than our typical PR, but
most of it comes from Jan's rework of audit's fanotify code; a very
welcome improvement. We ran this through our normal regression tests,
as well as some newly created stress tests and everything looks good.
Richard added a few patches, mostly cleaning up a few things and and
shortening some of the audit records that we send to userspace; a
change the userspace folks are quite happy about.
Finally YueHaibing and I kick in a few patches to simplify things a
bit and make the code less prone to errors.
Lastly, I want to say thanks one more time to everyone who has
contributed patches, testing, and code reviews for the audit subsystem
over the past year. The project is what it is due to your help and
contributions - thank you"
* tag 'audit-pr-20181224' of git://git.kernel.org/pub/scm/linux/kernel/git/pcmoore/audit: (22 commits)
audit: remove duplicated include from audit.c
audit: shorten PATH cap values when zero
audit: use current whenever possible
audit: minimize our use of audit_log_format()
audit: remove WATCH and TREE config options
audit: use session_info helper
audit: localize audit_log_session_info prototype
audit: Use 'mark' name for fsnotify_mark variables
audit: Replace chunk attached to mark instead of replacing mark
audit: Simplify locking around untag_chunk()
audit: Drop all unused chunk nodes during deletion
audit: Guarantee forward progress of chunk untagging
audit: Allocate fsnotify mark independently of chunk
audit: Provide helper for dropping mark's chunk reference
audit: Remove pointless check in insert_hash()
audit: Factor out chunk replacement code
audit: Make hash table insertion safe against concurrent lookups
audit: Embed key into chunk
audit: Fix possible tagging failures
audit: Fix possible spurious -ENOSPC error
...
Pull EFI updates from Ingo Molnar:
"The main changes in this cycle were:
- Allocate the E820 buffer before doing the
GetMemoryMap/ExitBootServices dance so we don't run out of space
- Clear EFI boot services mappings when freeing the memory
- Harden efivars against callers that invoke it on non-EFI boots
- Reduce the number of memblock reservations resulting from extensive
use of the new efi_mem_reserve_persistent() API
- Other assorted fixes and cleanups"
* 'efi-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/efi: Don't unmap EFI boot services code/data regions for EFI_OLD_MEMMAP and EFI_MIXED_MODE
efi: Reduce the amount of memblock reservations for persistent allocations
efi: Permit multiple entries in persistent memreserve data structure
efi/libstub: Disable some warnings for x86{,_64}
x86/efi: Move efi_<reserve/free>_boot_services() to arch/x86
x86/efi: Unmap EFI boot services code/data regions from efi_pgd
x86/mm/pageattr: Introduce helper function to unmap EFI boot services
efi/fdt: Simplify the get_fdt() flow
efi/fdt: Indentation fix
firmware/efi: Add NULL pointer checks in efivars API functions
Pull RCU updates from Ingo Molnar:
"The biggest RCU changes in this cycle were:
- Convert RCU's BUG_ON() and similar calls to WARN_ON() and similar.
- Replace calls of RCU-bh and RCU-sched update-side functions to
their vanilla RCU counterparts. This series is a step towards
complete removal of the RCU-bh and RCU-sched update-side functions.
( Note that some of these conversions are going upstream via their
respective maintainers. )
- Documentation updates, including a number of flavor-consolidation
updates from Joel Fernandes.
- Miscellaneous fixes.
- Automate generation of the initrd filesystem used for rcutorture
testing.
- Convert spin_is_locked() assertions to instead use lockdep.
( Note that some of these conversions are going upstream via their
respective maintainers. )
- SRCU updates, especially including a fix from Dennis Krein for a
bag-on-head-class bug.
- RCU torture-test updates"
* 'core-rcu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (112 commits)
rcutorture: Don't do busted forward-progress testing
rcutorture: Use 100ms buckets for forward-progress callback histograms
rcutorture: Recover from OOM during forward-progress tests
rcutorture: Print forward-progress test age upon failure
rcutorture: Print time since GP end upon forward-progress failure
rcutorture: Print histogram of CB invocation at OOM time
rcutorture: Print GP age upon forward-progress failure
rcu: Print per-CPU callback counts for forward-progress failures
rcu: Account for nocb-CPU callback counts in RCU CPU stall warnings
rcutorture: Dump grace-period diagnostics upon forward-progress OOM
rcutorture: Prepare for asynchronous access to rcu_fwd_startat
torture: Remove unnecessary "ret" variables
rcutorture: Affinity forward-progress test to avoid housekeeping CPUs
rcutorture: Break up too-long rcu_torture_fwd_prog() function
rcutorture: Remove cbflood facility
torture: Bring any extra CPUs online during kernel startup
rcutorture: Add call_rcu() flooding forward-progress tests
rcutorture/formal: Replace synchronize_sched() with synchronize_rcu()
tools/kernel.h: Replace synchronize_sched() with synchronize_rcu()
net/decnet: Replace rcu_barrier_bh() with rcu_barrier()
...
Only the mount namespace code that implements mount(2) should be using the
MS_* flags. Suppress them inside the kernel unless uapi/linux/mount.h is
included.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Reviewed-by: David Howells <dhowells@redhat.com>
The kernel commandline parameter named in CONFIG_PSI_DEFAULT_DISABLED
help text contradicts the documentation in kernel-parameters.txt, and
the code. Fix that.
Link: http://lkml.kernel.org/r/20181203213416.GA12627@cmpxchg.org
Fixes: e0c274472d ("psi: make disabling/enabling easier for vendor kernels")
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAlwEZdIeHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGAlQH/19oax2Za3IPqF4X
DM3lal5M6zlUVkoYstqzpbR3MqUwgEnMfvoeMDC6mI9N4/+r2LkV7cRR8HzqQCCS
jDfD69IzRGb52VSeJmbOrkxBWsR1Nn0t4Z3rEeLPxwaOoNpRc8H973MbAQ2FKMpY
S4Y3jIK1dNiRRxdh52NupVkQF+djAUwkBuVk/rrvRJmTDij4la03cuCDAO+Di9lt
GHlVvygKw2SJhDR+z3ArwZNmE0ceCcE6+W7zPHzj2KeWuKrZg22kfUD454f2YEIw
FG0hu9qecgtpYCkLSm2vr4jQzmpsDoyq3ZfwhjGrP4qtvPC3Db3vL3dbQnkzUcJu
JtwhVCE=
=O1q1
-----END PGP SIGNATURE-----
Merge tag 'v4.20-rc5' into for-4.21/block
Pull in v4.20-rc5, solving a conflict we'll otherwise get in aio.c and
also getting the merge fix that went into mainline that users are
hitting testing for-4.21/block and/or for-next.
* tag 'v4.20-rc5': (664 commits)
Linux 4.20-rc5
PCI: Fix incorrect value returned from pcie_get_speed_cap()
MAINTAINERS: Update linux-mips mailing list address
ocfs2: fix potential use after free
mm/khugepaged: fix the xas_create_range() error path
mm/khugepaged: collapse_shmem() do not crash on Compound
mm/khugepaged: collapse_shmem() without freezing new_page
mm/khugepaged: minor reorderings in collapse_shmem()
mm/khugepaged: collapse_shmem() remember to clear holes
mm/khugepaged: fix crashes due to misaccounted holes
mm/khugepaged: collapse_shmem() stop if punched or truncated
mm/huge_memory: fix lockdep complaint on 32-bit i_size_read()
mm/huge_memory: splitting set mapping+index before unfreeze
mm/huge_memory: rename freeze_page() to unmap_page()
initramfs: clean old path before creating a hardlink
kernel/kcov.c: mark funcs in __sanitizer_cov_trace_pc() as notrace
psi: make disabling/enabling easier for vendor kernels
proc: fixup map_files test on arm
debugobjects: avoid recursive calls with kmemleak
userfaultfd: shmem: UFFDIO_COPY: set the page dirty if VM_WRITE is not set
...
Pull RCU changes from Paul E. McKenney:
- Convert RCU's BUG_ON() and similar calls to WARN_ON() and similar.
- Replace calls of RCU-bh and RCU-sched update-side functions
to their vanilla RCU counterparts. This series is a step
towards complete removal of the RCU-bh and RCU-sched update-side
functions.
( Note that some of these conversions are going upstream via their
respective maintainers. )
- Documentation updates, including a number of flavor-consolidation
updates from Joel Fernandes.
- Miscellaneous fixes.
- Automate generation of the initrd filesystem used for
rcutorture testing.
- Convert spin_is_locked() assertions to instead use lockdep.
( Note that some of these conversions are going upstream via their
respective maintainers. )
- SRCU updates, especially including a fix from Dennis Krein
for a bag-on-head-class bug.
- RCU torture-test updates.
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Mel Gorman reports a hackbench regression with psi that would prohibit
shipping the suse kernel with it default-enabled, but he'd still like
users to be able to opt in at little to no cost to others.
With the current combination of CONFIG_PSI and the psi_disabled bool set
from the commandline, this is a challenge. Do the following things to
make it easier:
1. Add a config option CONFIG_PSI_DEFAULT_DISABLED that allows distros
to enable CONFIG_PSI in their kernel but leave the feature disabled
unless a user requests it at boot-time.
To avoid double negatives, rename psi_disabled= to psi=.
2. Make psi_disabled a static branch to eliminate any branch costs
when the feature is disabled.
In terms of numbers before and after this patch, Mel says:
: The following is a comparision using CONFIG_PSI=n as a baseline against
: your patch and a vanilla kernel
:
: 4.20.0-rc4 4.20.0-rc4 4.20.0-rc4
: kconfigdisable-v1r1 vanilla psidisable-v1r1
: Amean 1 1.3100 ( 0.00%) 1.3923 ( -6.28%) 1.3427 ( -2.49%)
: Amean 3 3.8860 ( 0.00%) 4.1230 * -6.10%* 3.8860 ( -0.00%)
: Amean 5 6.8847 ( 0.00%) 8.0390 * -16.77%* 6.7727 ( 1.63%)
: Amean 7 9.9310 ( 0.00%) 10.8367 * -9.12%* 9.9910 ( -0.60%)
: Amean 12 16.6577 ( 0.00%) 18.2363 * -9.48%* 17.1083 ( -2.71%)
: Amean 18 26.5133 ( 0.00%) 27.8833 * -5.17%* 25.7663 ( 2.82%)
: Amean 24 34.3003 ( 0.00%) 34.6830 ( -1.12%) 32.0450 ( 6.58%)
: Amean 30 40.0063 ( 0.00%) 40.5800 ( -1.43%) 41.5087 ( -3.76%)
: Amean 32 40.1407 ( 0.00%) 41.2273 ( -2.71%) 39.9417 ( 0.50%)
:
: It's showing that the vanilla kernel takes a hit (as the bisection
: indicated it would) and that disabling PSI by default is reasonably
: close in terms of performance for this particular workload on this
: particular machine so;
Link: http://lkml.kernel.org/r/20181127165329.GA29728@cmpxchg.org
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Tested-by: Mel Gorman <mgorman@techsingularity.net>
Reported-by: Mel Gorman <mgorman@techsingularity.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
efi_<reserve/free>_boot_services() are x86 specific quirks and as such
should be in asm/efi.h, so move them from linux/efi.h. Also, call
efi_free_boot_services() from __efi_enter_virtual_mode() as it is x86
specific call and ideally shouldn't be part of init/main.c
Signed-off-by: Sai Praneeth Prakhya <sai.praneeth.prakhya@intel.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Arend van Spriel <arend.vanspriel@broadcom.com>
Cc: Bhupesh Sharma <bhsharma@redhat.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: Eric Snowberg <eric.snowberg@oracle.com>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Joe Perches <joe@perches.com>
Cc: Jon Hunter <jonathanh@nvidia.com>
Cc: Julien Thierry <julien.thierry@arm.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Matt Fleming <matt@codeblueprint.co.uk>
Cc: Nathan Chancellor <natechancellor@gmail.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Sedat Dilek <sedat.dilek@gmail.com>
Cc: YiFei Zhu <zhuyifei1999@gmail.com>
Cc: linux-efi@vger.kernel.org
Link: http://lkml.kernel.org/r/20181129171230.18699-7-ard.biesheuvel@linaro.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Now that all RCU flavors have been consolidated, rcu_barrier_sched()
is but a synonym for rcu_barrier(). This commit therefore replaces
the former with the latter.
Signed-off-by: Paul E. McKenney <paulmck@linux.ibm.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: "Steven Rostedt (VMware)" <rostedt@goodmis.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: <linux-mm@kvack.org>
ARC, ARM, ARM64 and Unicore32 are all capable of parsing the "initrd="
command line parameter to allow specifying the physical address and size
of an initrd. Move that parsing into init/do_mounts_initrd.c such that
we no longer duplicate that logic.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Mike Rapoport <rppt@linux.ibm.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Make phys_initrd_start and phys_initrd_size global variables declared in
init/do_mounts_initrd.c such that we can later have generic code in
drivers/of/fdt.c populate those variables for us.
This requires both the ARM and unicore32 implementations to be properly
guarded against CONFIG_BLK_DEV_INITRD, and also initialize the variables
to the expected default values (unicore32).
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Mike Rapoport <rppt@linux.ibm.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Remove the CONFIG_AUDIT_WATCH and CONFIG_AUDIT_TREE config options since
they are both dependent on CONFIG_AUDITSYSCALL and force
CONFIG_FSNOTIFY.
Signed-off-by: Richard Guy Briggs <rgb@redhat.com>
Signed-off-by: Paul Moore <paul@paul-moore.com>
This removes a bunch of core and elevator related code. On the core
front, we remove anything related to queue running, draining,
initialization, plugging, and congestions. We also kill anything
related to request allocation, merging, retrieval, and completion.
Remove any checking for single queue IO schedulers, as they no
longer exist. This means we can also delete a bunch of code related
to request issue, adding, completion, etc - and all the SQ related
ops and helpers.
Also kill the load_default_modules(), as all that did was provide
for a way to load the default single queue elevator.
Tested-by: Ming Lei <ming.lei@redhat.com>
Reviewed-by: Omar Sandoval <osandov@fb.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
When a memblock allocation APIs are called with align = 0, the alignment
is implicitly set to SMP_CACHE_BYTES.
Implicit alignment is done deep in the memblock allocator and it can
come as a surprise. Not that such an alignment would be wrong even
when used incorrectly but it is better to be explicit for the sake of
clarity and the prinicple of the least surprise.
Replace all such uses of memblock APIs with the 'align' parameter
explicitly set to SMP_CACHE_BYTES and stop implicit alignment assignment
in the memblock internal allocation functions.
For the case when memblock APIs are used via helper functions, e.g. like
iommu_arena_new_node() in Alpha, the helper functions were detected with
Coccinelle's help and then manually examined and updated where
appropriate.
The direct memblock APIs users were updated using the semantic patch below:
@@
expression size, min_addr, max_addr, nid;
@@
(
|
- memblock_alloc_try_nid_raw(size, 0, min_addr, max_addr, nid)
+ memblock_alloc_try_nid_raw(size, SMP_CACHE_BYTES, min_addr, max_addr,
nid)
|
- memblock_alloc_try_nid_nopanic(size, 0, min_addr, max_addr, nid)
+ memblock_alloc_try_nid_nopanic(size, SMP_CACHE_BYTES, min_addr, max_addr,
nid)
|
- memblock_alloc_try_nid(size, 0, min_addr, max_addr, nid)
+ memblock_alloc_try_nid(size, SMP_CACHE_BYTES, min_addr, max_addr, nid)
|
- memblock_alloc(size, 0)
+ memblock_alloc(size, SMP_CACHE_BYTES)
|
- memblock_alloc_raw(size, 0)
+ memblock_alloc_raw(size, SMP_CACHE_BYTES)
|
- memblock_alloc_from(size, 0, min_addr)
+ memblock_alloc_from(size, SMP_CACHE_BYTES, min_addr)
|
- memblock_alloc_nopanic(size, 0)
+ memblock_alloc_nopanic(size, SMP_CACHE_BYTES)
|
- memblock_alloc_low(size, 0)
+ memblock_alloc_low(size, SMP_CACHE_BYTES)
|
- memblock_alloc_low_nopanic(size, 0)
+ memblock_alloc_low_nopanic(size, SMP_CACHE_BYTES)
|
- memblock_alloc_from_nopanic(size, 0, min_addr)
+ memblock_alloc_from_nopanic(size, SMP_CACHE_BYTES, min_addr)
|
- memblock_alloc_node(size, 0, nid)
+ memblock_alloc_node(size, SMP_CACHE_BYTES, nid)
)
[mhocko@suse.com: changelog update]
[akpm@linux-foundation.org: coding-style fixes]
[rppt@linux.ibm.com: fix missed uses of implicit alignment]
Link: http://lkml.kernel.org/r/20181016133656.GA10925@rapoport-lnx
Link: http://lkml.kernel.org/r/1538687224-17535-1-git-send-email-rppt@linux.vnet.ibm.com
Signed-off-by: Mike Rapoport <rppt@linux.vnet.ibm.com>
Suggested-by: Michal Hocko <mhocko@suse.com>
Acked-by: Paul Burton <paul.burton@mips.com> [MIPS]
Acked-by: Michael Ellerman <mpe@ellerman.id.au> [powerpc]
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Chris Zankel <chris@zankel.net>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Guan Xuetao <gxt@pku.edu.cn>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Richard Weinberger <richard@nod.at>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tony Luck <tony.luck@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Move remaining definitions and declarations from include/linux/bootmem.h
into include/linux/memblock.h and remove the redundant header.
The includes were replaced with the semantic patch below and then
semi-automated removal of duplicated '#include <linux/memblock.h>
@@
@@
- #include <linux/bootmem.h>
+ #include <linux/memblock.h>
[sfr@canb.auug.org.au: dma-direct: fix up for the removal of linux/bootmem.h]
Link: http://lkml.kernel.org/r/20181002185342.133d1680@canb.auug.org.au
[sfr@canb.auug.org.au: powerpc: fix up for removal of linux/bootmem.h]
Link: http://lkml.kernel.org/r/20181005161406.73ef8727@canb.auug.org.au
[sfr@canb.auug.org.au: x86/kaslr, ACPI/NUMA: fix for linux/bootmem.h removal]
Link: http://lkml.kernel.org/r/20181008190341.5e396491@canb.auug.org.au
Link: http://lkml.kernel.org/r/1536927045-23536-30-git-send-email-rppt@linux.vnet.ibm.com
Signed-off-by: Mike Rapoport <rppt@linux.vnet.ibm.com>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Chris Zankel <chris@zankel.net>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Greentime Hu <green.hu@gmail.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Guan Xuetao <gxt@pku.edu.cn>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "James E.J. Bottomley" <jejb@parisc-linux.org>
Cc: Jonas Bonn <jonas@southpole.se>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Ley Foon Tan <lftan@altera.com>
Cc: Mark Salter <msalter@redhat.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Palmer Dabbelt <palmer@sifive.com>
Cc: Paul Burton <paul.burton@mips.com>
Cc: Richard Kuo <rkuo@codeaurora.org>
Cc: Richard Weinberger <richard@nod.at>
Cc: Rich Felker <dalias@libc.org>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Serge Semin <fancer.lancer@gmail.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The alloc_bootmem(size) is a shortcut for allocation of SMP_CACHE_BYTES
aligned memory. When the align parameter of memblock_alloc() is 0, the
alignment is implicitly set to SMP_CACHE_BYTES and thus alloc_bootmem(size)
and memblock_alloc(size, 0) are equivalent.
The conversion is done using the following semantic patch:
@@
expression size;
@@
- alloc_bootmem(size)
+ memblock_alloc(size, 0)
Link: http://lkml.kernel.org/r/1536927045-23536-22-git-send-email-rppt@linux.vnet.ibm.com
Signed-off-by: Mike Rapoport <rppt@linux.vnet.ibm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Chris Zankel <chris@zankel.net>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Greentime Hu <green.hu@gmail.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Guan Xuetao <gxt@pku.edu.cn>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "James E.J. Bottomley" <jejb@parisc-linux.org>
Cc: Jonas Bonn <jonas@southpole.se>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Ley Foon Tan <lftan@altera.com>
Cc: Mark Salter <msalter@redhat.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Palmer Dabbelt <palmer@sifive.com>
Cc: Paul Burton <paul.burton@mips.com>
Cc: Richard Kuo <rkuo@codeaurora.org>
Cc: Richard Weinberger <richard@nod.at>
Cc: Rich Felker <dalias@libc.org>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Serge Semin <fancer.lancer@gmail.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds
Ard Biesheuvel
Masahiro Yamada
Jens Axboe
Mike Rapoport
Paulo Alcantara (SUSE)
Catalin Marinas
Ingo Molnar
Johannes Berg
Rasmus Villemoes
David Howells
Matthias Maennich
Al Viro
Patrick Bellasi
Thomas Gleixner
Will Deacon
Matthew Garrett
Thiago Jung Bauermann
Peter Collingbourne
Kees Cook
Mauro Carvalho Chehab
Alexander Potapenko
Geert Uytterhoeven
Christoph Hellwig
Jani Nikula
Yuyang Du
Sebastian Andrzej Siewior
Joel Fernandes (Google)
Steven Price
Dan Williams
Nadav Amit
Nadav Amit
Sakari Ailus
David Engraf
Arnd Bergmann
Anshuman Khandual
Andrew Morton
Qian Cai
Elena Reshetova
Johannes Weiner
Jonathan Neuschäfer
Richard Guy Briggs
Paul Burton
Yi Wang
Alexey Dobriyan
Qian Cai
Baruch Siach
Li Zhijian
Sai Praneeth Prakhya
Paul E. McKenney
Florian Fainelli
Mike Rapoport